Consumables - DJ Blee -Supplying Optical Practices Since...
Transcript of Consumables - DJ Blee -Supplying Optical Practices Since...
E
Consumables
E 2 Lens Blocks and Adhesive Pads
E 8 Lens Protection and Anti-Torsion Foil
E 9 Anti-Foaming Agent
E 10 Abrasive Stones and Lens Marking Pens
E 12 Glues and Screw Securing
E 18 Oils and Cleaners
E 20 Dyes
E 21 Disinfectant Wipes
E 22 Tips & Tricks: Plasti Dip
E 24 Repair Colours and Repair Pens
E 27 Tips & Tricks: Polishing
E 28 Buffi ng Wheels and Brushes
E 30 Polishing and Grinding Wax
E 32 Abrasives
E 34 Solder and Flux
E2
12
3 4
1
2
3
4
NIDEK Lens Block Mini CupFlexible lens block for NIDEK machines with original NIDEK Mini pick up. For small and fl at shapes only.
Please use the matching B&S adhesive pad No. 2508 15 only!
Up to curve 6.
20 x 15 mm 10 pieces
NIDEK Lens Block Pliable CupFlexible lens block for NIDEK machines with original NIDEK pick up.
Due to the larger surface of the lens block the risk of axis distortion is reduced.
Please use the matching B&S adhesive pads No. 2502 17, 2503 17, 2506 17, 2507 17, 2508 17, 2510 17 or 2511 17 only!
Up to curve 8.
3710 17N
30 x 17 mm 10 pieces
Green (right lens) Mixed colours for right and left
lenses (5x red and 5x green)
Red (left lens)
3710 17R 3710 17G 3710 50
3711 17
For high curves from base 8.
30 x 17 mm 10 pieces
3714 15
Green (right lens) Mixed colours for right and left
lenses (5x red and 5x green)
Red (left lens)
3714 15R 3714 15G 3714 50
Lens Block
Adhesive Pad
Anti-Torsion Foil
Protection Foil (back of the lens)
E3
NIDEK Lens Block Nano CupFlexible lens block for NIDEK machine LEX 1000.
For very small and fl at shapes. To be used with the complete outer ring.
Please use the matching B&S adhesive pad No. 2503 13 only!
Up to curve 6.
30 x 17mm/18 x 13.5 mm 10 pieces
Green (right lens)Red (left lens)
3715 13R 3715 13G 3715 13
White
Flat curve
3700 20
25 x 20 mm
10 pieces
Red
For high plus lenses
3700 25
25 mm
25 pieces
White
Flat curve
Red
For high plus lenses
3701 20 3701 25
25 x 20 mm
10 pieces
25 mm
25 pieces
Mixed colours for right and left
lenses (5x red and 5x green)
Vario Block
Flexible plastic, for adhesive pads. Suitable for WECO-system.
E4
Adhesive Padsfor Super Hydrophobic Lenses
• Material: Ethyl vinyl acetate foam
• Including anti-torsion foil
• In a dispenser box 1 roll (500 pieces)0.9 mm
2511 17 2511 19 2511 22 2511 24
in mm
31 x 17
30 x 18
22
24
Order No.
2511 17
2511 19
2511 22
2511 24
Adhesive power Protection against axis slip Type for blocker
NIDEK
Universal
Universal
Universal
No. 3710 . . | 3711 17
very high, for
super hydrophobic lenses
very high, including
anti-torsion foil
• Material: Ethyl vinyl acetate foam
• Including anti-torsion foil
• In a dispenser box 1 roll (500 pieces)0.9 mm
2510 17 2510 18 2510 24
in mm
31 x 17
30 x 18
24
Order No.
2510 17
2510 18
2510 24
Adhesive power Protection against axis slip Type for blocker
NIDEK
Universal
Universal
No. 3710 . . | 3711 17
high, for
super hydrophobic lenses
high, including
anti-torsion foil
Adhesive pads should not be stored longer than 6–12 months
depending on the material. Storage should be at room tempe-
rature (approx. + 18 °C) and with a humidity of approx. 30 %.
For an optimum adhesive strength please store the adhesive
pads in your refrigerator and remove them 15 minutes before
using them!
E5
Adhesive Pads for Hydrophobic Lenses
• Material: Ethyl vinyl acetate foam
• In a dispenser box 1 roll (500 pieces)
in mm
21 x 14
31 x 17
30 x 18
22
24
Order No.
2507 14
2507 17
2507 18
2507 22
2507 24
Adhesive power Protection against axis slip Type for blocker
Universal
NIDEK
Universal
Universal
Universal
No. 3710 . . | 3711 17
very high, for
hydrophobic lensesvery high
2507 14
2507 22
2507 17
2507 24
2507 18
• Material: Polyurethane foam
• In a resealable polybag 10 strips (200 pieces)
in mm
22 x 15.5
31 x 17
18
24
Order No.
2508 15
2508 17
2508 18
2508 24
Adhesive power Protection against axis slip Type for blocker
NIDEK Mini-Cup
NIDEK
Universal
Universal
No. 3714 . .
No. 3710 . . | 3711 17high, for
hydrophobic lenseshigh
2508 15 2508 242508 17 2508 18
0.9 mm
0.9 mm
E6
2503 13 2503 17 2503 18 2503 26
2502 17 2502 18 2502 19
2502 24
• Material: PVC fi lm
• Comparable with 411 quality (thin very strong line)
• In a dispenser box
(pieces)in mm
32 x 17
18
28 x 18
30 x 21
24
Order No.
2502 17
2502 18
2502 19
2502 21
2502 24
Adhesive power Protection against axis slip Type for blocker
NIDEK
Universal
Universal
Universal
Universal
No. 3710 . . | 3711 17
high, for
standard lenseshigh
1 roll (1,000)
1 roll (1,000)
1 roll (500)
1 roll (500)
1 roll (1,000)
2502 21
0.38 mm
Adhesive Pads for Standard Lenses
• Material: Ethyl vinyl acetate foam
• 3M Leap III Adhesive Pads – the original 3M with double pull tabs
• In a dispenser box
• In a resealable polybag (2503 13) 0.8 mm
(pieces)in mm
31 x 17
18
26
2503 17
2503 18
2503 26
Adhesive power Protection against axis slip Type for blocker
NIDEK
Universal
Universal
No. 3710 . . | 3711 17very high, for
standard lensesvery high 1 roll (1,000)
1 roll (1,000)
1 roll (1,000)
Order No.
2503 13 31 x 17
18 x 13.5NIDEK Nano-Cup No. 3715 13 (two-piece) 5 strips (100)
see table
see table
E7
2506 17 2501 24
2500 24
2501 18
in mm
31 x 17
18
24
30 x 18
24
Order No.
2506 17
2501 18
2501 24
2500 19
2500 24
Adhesive power Protection against axis slip Type for blocker
NIDEK
Universal
Universal
Universal
Universal
No. 3710 . . | 3711 17
high, for
standard lenseshigh
Adhesive Pads for Standard Lenses
• Material: Polyolefi n foam (2501 . .), Polyethylene foam
• In a dispenser box 1 roll (1,000 pieces)0.8 mm0.9 mm (2501 18)
2500 19
E8
2560 352560 41
GECKOlensgrip
• Grip spray for lenses with hydrophobic and clean effect coatings
• Prevents axis slippage during the edging process
• Works additionally as a protective fi lm to reduce the possibility of scratches and can be applied
on the front and back side
• Can easily be removed with conventional cleaning agents
• Dries quickly and is economical in use
2561 00
(pieces)in mm Product information Field of application
To protect the front and back of the lens during the edging
process. This protection foil is especially made for lenses
with high-quality coatings. Storing period for adhesive
pads: 6 months.
To protect the front and back of the lens during the edging
process. This protection foil is especially made for lenses
with high-quality coatings. Storing period for adhesive
pads: 6 months.
For high curved lenses. To protect the front and back of
the lens during the edging process. This protection foil
is especially made for lenses with high-quality coatings.
Storing period for adhesive pads: 6 months.
To protect the front and back of the lens during the edging
process. The improved glue of the foil increases the
adhesive power on all lenses with super hydrophobic
coatings. Storing period for adhesive pads: 6 months.
To protect the back of the lens during the edging process.
1 roll (500)
1 roll (500)
1 roll (500)
1 roll (500)
1 roll (1,000)
Lens Protection and Anti-Torsion Foil
2560 312560 30 2560 32
Order No.
Anti-torsion foil
2560 30
2560 31
2560 32
2560 41
2560 35
40 x 28
40 x 26
40 x 26
40 x 26
35
For lenses with + 4.5 dpt.
on the front surface.
For lenses with + 4.5 dpt.
on the front surface.
Oval shape for better
handling!
For lenses with high base
curve.
Especially fl exible!
For lenses with + 4.5 dpt.
on the front surface and super
hydrophobic lenses. Oval
shape for better handling!
100 ml
Lens protection
100 x 13 x 25 mm
E9
Top Product
Anti-Foaming Agent
• Prevents foaming during grinding process
• Protects machine parts from corrosion
• Improves overall care of the machine
• Rapid decline of dirt particles
• Has minimal aerosol development
• Contains no hazardous substances, is physiologically safe
• Mixing ratio: 200 ml grinding additive for 20 litre water
Anti-Foaming Agent, blue
• Prevents foaming during grinding process
• Improves the grinding process
• Cools and protects machine parts from corrosion
• Improves overall care of the machine
• Reduces the grinding foam
• Rapid decline of dirt particles
• Has minimal aerosol development
• Contains no hazardous substances, is physiologically safe
• Very effi cient (100 ml grinding additive for 20 litre water)
3148 50
3149 00
500 ml
1 l
Bag Insert for Grinding Water Tank
Made of grey, tearproof plastic.
2900 51
10 pieces800 x 560 x 0.06 mm
Environmentally friendly Anti-Foaming Agent
The 100 % ecological compatibility of this item together with its high yield and effectiveness have earned it the B&S
title of Top Product. Proving itself with its fi rst use it does away with any annoying creation of foam during the grinding
process. Another positive effect is the reduced corrosion of machine parts. Especially recommended by the B&S goes
Green team.
To prevent chemical reactions we recommend changing the water
for the edger latest every second week.
E10
Replacement Leads
• Suitable for retractable graphite pencil No. 2624 02 and 2624 05
• In plastic box
Lens Marking Pen
• Especially for lenses with clean effect coatings
• Water resistant
• Remove colour with spirit alcohol
• In a patent-registered box
• Two types: fi ne and super fi ne
Retractable Graphite Pencil
• Applicable to foils, spectacle lenses and even surfaces
• White is recommended for dark materials, especially for tinted lenses
• Refi llable with leads No. 2624 22 and 2624 55
2625 01
2625 05
2627 01
4 pieces
4 pieces
4 pieces
Black, fi ne
2624 02
2624 05
2624 22
2624 55
12 pieces
12 pieces
Red, fi ne
Black, super fi ne
Red
White
Red
White
• Colour: White
• Type: Fine
• Granulation: 320
• Field of application: Diamond wheels of edgers
• Colour: Red
• Type: Rough
• Granulation: 120
• Field of application: Diamond wheels of edgers
• Colour: Light blue
• Type: Very fi ne
• Granulation: 1,500
• Field of application: Diamond polishing wheel
3419 00
3423 12
3422 12
3424 01
• Type: Fine
• Field of application: Diamond wheels, fi ne
Abrasive Stones
100 x 8 x 25 mm
100 x 13 x 25 mm
110 x 12 x 25 mm
100 x 13 x 25 mm
40 g
831 g
927 g
80 g
12 pieces
12 pieces
Whetstone for Hand Edger, green
Lens Marking Pen
• Especially for lenses with clean effect coatings
• Light, water and abrasion resistant ink
• Dries quickly and can be removed with spirit alcohol
• Stroke width: 0.8 mm
• Tip: round tip
2620 02 2 piecesWhite
E11
Universal Pen, Fine
• Waterproof for permanent marking
• With dry safe function – pen can stay open for hours
without running dry
• In a patent-registered box
2623 01
2623 05
4 pieces
4 pieces
Black
Red
Ink Remover Pen
The marking on lenses can be easily removed with this ink remover pen
and can be used on all types of lens material.
2630 00
Foil Pen
Water soluble, smudge-proof foil pen for occlusion foils,
lenses and prism foils.
2628 01 Black 2 pieces
E12
3184 10
3184 09
3184 03
UV Gel 3184 . .
Use for fi lling in drill holes accidentally drilled too large or incorrectly.
The gel cures fi rmly when exposed to the UV lamp.
• Glue cures through UV rays
• To use for fi tting rimless frames
• Also suitable for poly carb onate
• Transparent, dries very hard
• Glue can be drilled once completely hardened
Accessories: UV Gel Inverted Holder
• UV glue is always ready for use and can be used up to the last drop
• Stable and perfect for immediate use
• No air bubbles in the cannula
• Supplied without application bottle
a)UV Gel Applicator
• Perfect for delicate fi ttings
• Handy, convenient
• No air bubbles in the cannula
b)UV Gel Application Bottle
• Convenient application bottle
• Reclosable
• With application tip for precise dispensing
3184 03 3 ml
3184 10 10 ml 3184 09 40 x 65 x 50 mm
Available as:
You will fi nd our UV lamps No. 2430 20 and 2420 10 on page A 44.
Conical shape
for easier
dispensing
E13
3186 00
Proformic UV Glue
• Can be applied in several layers
• Cure with special developed and included LED
• Can be reworked in cured condition
• Color after cure is transparent to slightly yellowish
• Solvent-free
• Delivered in a metal case
Refi ll Cartridge
3186 01 4 g
4 g
E14
Loctite 4850
• Superglue especially for polycarbonate
and Trivex
• Stays fl exible after curing
• Colour: Transparent
Loctite 460
• Superglue
• Also suitable for poly carb onate
and Trivex lenses
• Colour: Transparent
3162 00 3162 10
3162 02
Instant Adhesive
Universal Adhesive
Loctite 454 Gel
• General purpose gel
• Ideal when non-drip application is required or for use
on vertical or overhead surfaces
• Stays correctable for several seconds
• Ideally suited for applying rhinestones
• Not suitable for polycarbonate and Trivex lenses
3162 30
Loctite 401
• All-purpose adhesive
• Also suitable for wood
• Not suitable for polycarbonate
and Trivex lenses
• Colour: Transparent
3162 20
3177 00
3163 00
Glass Adhesive
• To glue lenses into all types of frames, also to be applied
as a liquid lining
Loctite Glass Glue 3494
• Suitable for fi xing correction lenses in diving masks
• Solvent-free and crystal clear one-component glue
• For glass and UV permeable plastics
Glass Glues
B&S Silicone Adhesive
A must have for all rimless frames. Transparent special silicone with
a refraction index of 1.56 allows for the carefree bonding and padding
on drilled spectacles.
• Silicone is 100 % compatible with all materials
• Maintains its fl exibility
• Suitable for polycarbonate and Trivex
• Tested and recommended by “Flair Modellbrillen”
3181 30
20 g5 g
20 g
5 g 3 g
25 ml 10 ml
9 ml
E15Superglue Liquid
• Solvent-free
• Multi-use and economical
• Also suitable for polycarbonate
Plastic and all Purpose Glues
3183 02
Adhesive SICO MET 40
• Fast curing, solvent-free super glue
with high fl ow rate
• Sticks together in seconds
• Also suitable for polycarbonate
3185 30
3185 12
Solvent for glue
• Newly developed Pen-System which enables
pen positioning
• Easy application, clean processing and
improved dosing
• Solvent for all cyanoacrylate glues
• Short curing time
• Not suitable for polycarbonate and
Trivex lenses
3185 22
Super Glue
• Newly developed Pen-System which enables
pen positioning
• Easy application, clean processing and
improved dosing
• Area of application: plastics, rubber, metal,
balsa wood, leather
• Final strength after 24 hours
• Not suitable for polycarbonate and
Trivex lenses
Screw Grip
• To remove screws with a damaged head
• Immediate effectiveness (without curing)
• Simply wipe off after use
3168 00
12 g 30 g
20 g 3 ml
20 g
• The fi lling level of the glues can vary due to the production process
• The details of the fi rmness refer to the usage of frame screws and can therefore differ to the manufacturers information
E16
Loctite 221
• Low fi rmness
• Colour: Red
Loctite 243
• High fi rmness
• Colour: Blue
Loctite 259
• Low fi rmness
• Colour: Red
Screw Securing
Screw Fastener withPatented Dispenser Tip
• Low fi rmness
• Colour: Blue
3159 00
3161 15 3178 00
3161 00
3161 05
LOCK AN 302-21
• Newly developed Pen-System which enables
pen positioning
• Easy application, clean processing and
improved dosing
• Low fi rmness
• Colour: Red
Comparable with Loctite 221
3160 00
LOCK AN 302-43
• Newly developed Pen-System which enables
pen positioning
• Easy application, clean processing and
improved dosing
• High fi rmness
• Colour: Blue
Comparable with Loctite 243
3164 00
3164 05
10 ml
10 ml
50 ml
20 ml 10 ml
50 ml
50 ml 10 g
• The fi lling level of the glues can vary due to the production process
• The details of the fi rmness refer to the usage of frame screws and can therefore differ to the manufacturers information
E17
1406 00 1407 00
Stand for Mixing Mould Mixing Mould
6 pieces21 mm
Application Tips
• Short metal tip for easy dispensing of super glue
• Long, fl exible plastic tip can be shortened if tip becomes blocked
• Inner diameter: each with 0.84 and 0.25 mm
Application Tips made of Plastic
• For exact dispensing of screw fastener
• Inner diameter: 0.84; 0.5 and 0.41 mm
1405 10 1405 203 pieces 4 pieces
1488 03
Plastic Bottle
• Material: LDPE
• Capacity: 1 l
1486 00
Pipettes for Single Use
• Total length: 137 mm
• Capacity: 4.8 ml
• Material: LDPE (Polyethylene)
• Suitable to use with acetone and spirit
10 pieces
E18
1487 10
Fluid Dispenser
• Fluid dispenser for acetone, alcohol etc.
• Pump mechanism, can be used with one
hand, reduces odour, plastic HDPE, with
steel cover
• With pre-printed sticky labels
• Capacity: 125 ml
Fluid dispenser
• Fluid dispenser for acetone, alcohol etc.
• Pump mechanism, can be used with
one hand, reduces odour
• PP material with plastic cover
• Capacity: 120 ml
1489 00 3 pieces
Acetone
• To bond plastic frames
• To clean surfaces
• For plastic frames (no Optyl)
Special Cleaner forSpectacle Lenses
• Cleaner for polycarbonate, plastic and
Trivex lenses
• Ideal for removing residues of the B&S
silicone adhesive No. 3163 00
3173 00 3175 00
3175 10
Oil
• For spectacle hinges, high quality, non-acidic
3171 00
Drill Oil
• For cooling during drilling
3170 00
Oil Dropper
• Body made of aluminum
• With single drop release
• Use for acid-free oil and also alkali oil
• Capacity: 5 ml
2742 00 145 mm
100 ml 100 ml
1 l
20 ml 100 ml
E19
Compressed-Air Spray
Removes dust and fl uff quickly and reliably from sensitive surfaces and
parts which are not easily accessible.
Applications: Optics, instruments, medical technology, clock pieces,
keyboards, hi-fi , videos, electrical equipment and model making
3174 15
Silicone Care Spray
Cleans and protects automatic grinders, machinery and equipment.
Impregnates rubber, plastic and leather. Repels dirt and water, eases
friction parts. Protects against corrosion and oxidation.
Important!
Do not allow spray to come into contact with spectacle lenses.
3174 10
Cleaning Concentrate
Alkaline cleaning concentrate, 1:9 ratio; for extremely dirty metal frames,
jewellery and other metal parts, for ultrasonic cleaners. The ammonia
ingredient will brighten and freshen up the fi ne metals as well as
coloured metals in an optimal way. The cleaned parts should be rinsed
thoroughly under running water and then dried.
Do not use this cleaning solution on polycarbonate and Trivex
lenses or other coated plastic lenses.
OPTOCLEAN
Cleaning concentrate 1:20 for frames and lenses (also plastic lenses) in
combination with ultra sound. Dilute with 20 parts water, rinse clean parts
with running water and dry.
OPTOCLEAN is a very effective but mild cleaning solution which
is suitable for cleaning sensitive materials such as polycarbonate
and Trivex.
3157 00 1 l
3158 00
3157 25 2.5 l
1 l
400 ml
400 ml
You will fi nd our Ultrasonic baths on page A 8 to A 13.
E20
Lens Dye Packets
• Water soluble dye powder for tinting lenses
• Ready prepared for 1 litre tinting solution
• The powder bag dissolves completely when mixed with hot water 2615 . .
2615 29
Yellow
2615 26
Orange
2615 24
Red
2615 23
Fuchsia
2615 17
Blue
2615 16
Dark blue
2615 12
Green
2615 11
Dark green
2615 06
Brown
2615 04
Steel grey
2615 03
Grey blue
2615 02
Grey green (G-15)
2615 01
Black
10 g
You will fi nd our tinting unit Tinta 2 No. 2880 01 on page A 45.
E21
Disinfectant Wipes – Dispenser
• For cleaning and disinfecting of surfaces of refraction units,
autorefractometers, keratometers, etc.
• Effective spectrum against bacteria, fungus and viruses
(HCV, HIV, Infl uenza A&B, Polio)
• Skin friendly with a pH-value of 7.0
• 100 pieces: 180 x 125 mm
3154 01
Disinfectant Wipes – Refi ll Pack
• 100 pieces: 180 x 125 mm
3154 00
UV Filter Additive
• Water soluble powder
• To apply an UV fi lter on lenses
• UV-protection to 400 nm
• Ready prepared for 1 litre tinting solution
• The powder bag dissolves completely when mixed with hot water
2616 00
Heat Transfer Fluid
• Special oil, can be used instead of distilled water
• No loss of liquid by evaporation
• Especially suitable for frequent use
2617 00
Neutraliser
• Removes colour from tinted lenses
2618 00
35 g
1 l
1 l
E22
www.youtube.com/user/BreitfeldSchliekert
3
4
2
5
1
4 5 6
This is how it works
Option 1: Without thinner – for smooth surfaces (e.g. plier tips)
approx. 5–10 minutes
without drying period
Scratch Protection ina Twinkling of an Eye!
Plasti DipRubber Coating
Plasti Dip
No. 3169 20, 21, 22
Thinner
No. 3169 10
Container, syringe, stirring spoon
Tips & Tricks
Option 2: With thinner – for uneven surfaces (e.g. tip of the nose pad arm adjusting plier) | Repeat step 1–3
Cleaning Stirring
Drying
Decant undiluted
Dipping
Fill the syringe Mixing and dipping Drying
TIP: To avoid bubbles don't shake the Plasti Dip, stir carefully. Undiluted Plasti Dip can be refi lled into the Plasti Dip can.
Diluted Plasti Dip can be stored in a lidded can.
E23
Starter Set
Contains 3 colours (black, blue and red) and one bottle of thinner.
Plasti Dip
Plasti Dip Thinner
3169 . . 429 ml
3169 10 250 ml
3169 51
Plasti Dip – Professional Protection whilst Adjusting Frames
Protects, gives grip and stays fl exible
Plasti Dip – Multi-Purpose SyntheticRubber Coating
• Can be used on metal, glass, stone and wood
• Air drying synthetic rubber coating
• Easy to apply by dipping or brushing
• Food safe in cured condition
• 24 hours curing time
3169 20
3169 21
3169 22
Black
Blue
Red
E24
Repair Colours
Coloured quality lacquer for small repairs on frames, for example
re-colouring after soldering. The colours may be mixed. The clear
lacquer can be used for small repairs of protection lacquer and
to optimise the colours.
Repair Colour Set
Consisting of all 9 colours plus clear lacquer.
• Available in 9 colours plus clear lacquer:
2611 50
2611 . .
Order No.
2611 00
2611 01
2611 02
2611 03
2611 04
Colour
White
Black
Metallic silver
Metallic gold
Blue
Code Order No.
2611 05
2611 06
2611 07
2611 08
2611 09
Colour
Red
Yellow
Green
Brown
Clear Lacquer
Code
12 ml
• Thoroughly clean frame parts to be repaired
• Shake the bottle well, you must be able to hear the ball bearing
• Apply the colour to the desired area
• Allow 6 hours to dry
• If necessary apply an additional coat of clear lacquer
E25
Repair Pens
With repair pens you can successfully:
• Repair scratches
• Cover solder or welding traces
• Can also be used to cover corrosion caused by perspiration
Usable for metal and plastic frames.
Repair Pen Set
Consisting of 12 pens plus 1 corrector pen.
2612 . .
2612 50
• Available in 12 colours plus 1 corrector pen:
Order No.
2612 00
2612 01
2612 02
2612 03
2612 04
2612 05
2612 06
Colour
Gloss black
Matt black
Dark blue
Light blue
Rose gold
Yellow gold
Gunmetal
Code Order No.
2612 07
2612 08
2612 09
2612 10
2612 11
2612 12
Colour
Light silver
Light brown
Dark brown
Protective lacquer clear gloss
Protective lacquer clear matt
Corrector Pen
Code
• Thoroughly clean the frame part to be repaired
• Shake the pen and press the tip in several times until you see the colour come through
• Put the colour on the required area
• Leave to dry for 10 to 20 minutes. Use a frame heater to dry quicker
• A second coat of clear lacquer may be required
• Not appropriate for paint coats that have received heat treatment
E26
Lens Deco Pens
To colour lens edges and nylon threads.
For all materials including polycarbonate.
• One pen will colour over 300 lenses
• Air dry for only 20 minutes
• The colour can be removed with the corrector pen at any time,
no time limit
• Simply wipe off the colour with acetone or spirit with the exception
of polycarbonate lenses
• Available in 15 colours plus 1 corrector pen:
All included in No. 2610 51
Lens Deco Pen Set
• Consisting of 12 pens plus 1 corrector pen
• We reserve the right to change the assortment
2610 51
2610 . .
Order No.
2610 01
2610 02
2610 03
2610 04
2610 05
2610 06
2610 07
2610 08
Colour
Black
Violet
Ochre
Cognac
Fuchsia
Grey
Plum
Dark green
Code
4
5310
5315
5326
5328
5330
5331
5332
Code Order No.
2610 09
2610 10
2610 11
2610 12
2610 13
2610 14
2610 15
2610 00
Colour
Light turquoise
Rose
Bronze
Blue
Brown
Bordeaux
Light blue
Corrector Pen
Code
5341
5617
5634
5636
5340
5333
5339
Code
Clean the lens edge thoroughly with lens cleaner No. 3175 00 or with an ultrasonic cleaning unit before application.
For best results do not polish the lens edge. Shake the pen and gently push in the cartridge to fi ll with colour.
For easy application attach the lens to a lens groover. Use lens cleaner No. 3175 00 to clean lens after application.
Please screw cap on tightly after each use to prevent the pen from drying out.
E27
www.youtube.com/user/BreitfeldSchliekertTips & Tricks
Buffi ng Wheel?+ Polishing
Wax?= The Combinationis Important!
Perfectly Polished
This is how it works
BAKELITE, HORN, CAOUTCHOUC, METAL
ACETATE, OPTYL, CELLULOID, PROPIONATE
ROUGH POLISHING
Grinding wax
No. 3120 00
FINE POLISHING
Polishing wax
No. 3122 00, 3118 00
HIGH GLOSS POLISHING
Burnishing wax
No. 3125 00,
No. 3118 00
POLYCARBONATE
LENS POLISHING
Polishing past
No. 3127 00
CR 39, TRIVEX, PNX
ROUGH POLISHING
Polishing paste
No. 3128 00, 3129 01
FINE POLISHING
Polishing paste
No. 3128 00, 3129 01
STEEL, WHITE AND PRECIOUS METALS
ROUGH POLISHING
Polishing wax
No. 3144 00
FINE POLISHING
Polishing wax
No. 3143 00
without any wax
Buffi ng wheel
No. 3416 10, 3474 00
Buffi ng wheel
No. 3416 10, 3474 00
Buffi ng wheel, wool cone
No. 3470 01, 3471 00, 3472 00,
No. 3561 00, 3582 00, 3571 00
Felt cloth buff
No. 3457 00
Leather buffi ng wheel
No. 3462 00
Buffi ng wheels
No. 3471 00, 3470 01, 3472 00,
No. 3474 00, 3416 10
Buffi ng wheels
No. 3471 00, 3470 01, 3472 00,
No. 3474 00, 3416 10
Felt cloth buff
No. 3474 00, 3457 00
Felt discs
No. 3455 10, 3450 00, 3456 00
E28
Felt Disc, conical shaped Soft Set Felt
• Core: Centered
• Bore Ø: 8 mm
Felt Buffi ng Wheel
• Core: Plastic
• Bore Ø: Conical
Felt Discwith Groove
• Core: Centered
• Bore Ø: 8 mm
Felt Disc
• Core: Centered
• Bore Ø: 8 mm
Felt Cloth Bufffor Polycarbonate
To extend service life the red rings
can be separated individually.
The felt cloth buff in combination
with the polishing wax
No. 3127 00, is perfectly suited
for polishing Polycarbonate
lenses – optimum speed for the
treatment of Polycarbonate:
approx. 1,500 rpm.
• Core: Plastic
• Bore Ø: Conical
Leather Buffi ng Wheel
No. 3462 00 is especially suitable
for the fi nal polishing of metal
rubber, paladon, bakelite, horn etc.
Use the wheel dry without any
polishing compound.
• Core: Plastic
• Bore Ø: Conical
Muslin Buffi ng Wheel
• Core: Leather
• Bore Ø: 6 mm
Muslin Buffi ng Wheel
• Core: Leather
• Bore Ø: 6 mm
3418 00
100 mm 15 mm
3450 00
100 mm 20:5 mm
3455 10
100 mm 25 mm
3456 00
100 mm 25 mm
3457 00
80 mm 25 mm
3462 00
90 mm 6 mm
3470 01
125 mm 12 mm
3471 00
125 mm 24 mm
E29
Buffi ng Wheel
• Core: Plastic
• Bore Ø: 8 mm
Flannel Buffi ng Wheel
• Core: Leather
• Bore Ø: 6 mm
Wool Brush
• Core: Wood
• Bore Ø: 6 mm
Yarn Brush
• Core: Plastic
• Bore Ø: Conical
Buffi ng Wool Cone
The buffi ng wool cone is manu-
factured in such a way that it can
be mounted on a conical polishing
tip. A different kind of fi xing is not
available. Due to the length of the
axis unbalanced run may occur.
• Core: Wood
• Bore Ø: Conical
Wool Brush
• Core: Plastic
• Bore Ø: Conical
3474 00
125 mm 30 mm
3416 10
100 mm 10 mm
3561 00
70 mm 35 mm
3582 00
80 mm 25 mm
3575 00
90 mm 20 mm
3571 00
30:15 mm 70 mm
Silicone Impregnated Muslin Wheel
This silicone impregnated fabric
structure offers signifi cant advan-
tages: it increases the life of the
buffi ng wheel, due to elimination
of fl uff. They require less pressure
during the polishing process and
save 50 % on polishing paste.
• Core: Plastic
• Bore Ø: 6 mm
3472 00
100 mm 12 mm
To prevent polishing buffs from fraying these can be napped
before fi rst use using a sharp object. However due to the
properties of the material cotton cloth is not completely
free of fl uff.
For all buffi ng wheels with plastic core
Plastic cores have conical borings. While attaching
to the po lish ing tip, the cone of the tip and the boring
have to match.
Corresponding to the “European Safety Regulations
for the correct use of grinding wheels” the following
has to be observed:
1. Wheels with a total diameter of 100 mm or more
have to be fl anged ⅔ on both sides.
2. The maximum running speed has to be observed.
3. During operation safety goggles (see accessories catalogue)
have to be worn.
“Perfectly Polished”
(see page E 27)
To ensure the buffi ng wool cone No. 3571 00 runs safely it’s
necessary to check if the cone can be screwed onto the polishing
tip for at least 2 cm.
E30
3145 00
Polishing Paste
• Finest polishing compounds
• High amount of grease: smears
more easily and cools off faster
3128 00 3129 01
Poligreen
Buffi ng and smooth polishing:
Cloth buffi ng wheels
White metals
approx. 60 g
3144 00
Buffi ng and smooth polishing:
Cloth buffi ng wheels
Plastic and caoutchouc rubber
approx. 60 g
Applications with approx. 2,800 rpm:
Field of application:
Weight:
Poliblue
Chamois Polishing Paste
• Finest polishing compounds
• Grease free: has no cooling
effect during polishing
High gloss polishing:
Cloth buffi ng wheels
CR 39, precious metals
approx. 50 g
High gloss polishing:
Cloth buffi ng wheels, wool wheels
CR 39, precious metals
approx. 100 g
Applications with approx. 2,800 rpm:
Field of application:
Weight:
Polired
3143 00
Buffi ng and smooth polishing:
Cloth buffi ng wheels
Gold, steel
approx. 60 g
Applications with approx. 2,800 rpm:
Field of application:
Weight:
For No. 3128 00 and 3129 01
Finest polishing compounds contain an especially fi ne and treated polishing powder. The speed of the polishing machine should be very slow
and you should use felt discs.
Please take note of our small tools assortment including the silicone polisher No. 2240 57 on page C 33.
E31
3118 00
Grinding Wax, grey
Rough polishing: Cloth buffi ng wheels
(approx. 2,300 rpm)
Plastic
approx. 200 g
3120 00
Buffi ng and smooth polishing:
Wool wheels, cloth buffi ng wheels
Plastic, optyl
approx. 700 g
Applications with approx. 2,800 rpm:
Field of application:
Weight:
Polishing Wax, blue
3125 00
Burnishing Wax, beige
Smooth polishing: Wool wheels,
cloth buffi ng wheels
Plastic
approx. 200 g
3122 00
High glossing polishing: Wool wheels
Plastic
approx. 200 g
Applications with approx. 2,800 rpm:
Field of application:
Weight:
Burnishing Wax, beige
Polishing Wax, blue, for Polycarbonate
The polishing paste is a high gloss polishing paste with “Dia mantine” being perfectly suited for polishing
Poly carbonate lenses as well as for the materials Titanium, Platinum and Palladium. The best polishing
results will be achieved with the felt cloth No. 3457 00 which has a patented conical fl ange (refer to page
E 28).
3127 00
High gloss polishing: Felt cloth buffi ng wheel,
wool wheels
Polycarbonate, Titanium, Palladium, Platinum
approx. 100 g
Applications with approx. 2,800 rpm:
Field of application:
Weight:
You will fi nd our polishing motors
on page A 28 and A 29.
“Perfectly Polished”
(see page E 27)
E32
Abrasive Paper
Abrasive Rubber
To clean solder points, to dull metals and plastic.
3251 18
3251 24
3251 32
3251 40
3251 60
3251 80
Granulation: 180
Granulation: 240
Granulation: 320
Granulation: 400
Granulation: 600
Granulation: 800
3412 01
3412 02
3412 03
Granulation: Rough
Granulation: Medium
Granulation: Fine
3251 . .
3412 . .
Abrasive Bar, fl at
• Working area: 230 x 18 x 4 mm
3253 10
3253 22
3253 40
Granulation: 100
Granulation: 220
Granulation: 400
3253 . .
Abrasive Bar, triangular
• Working area: 230 x 11 mm
• Working angle: 60°
3254 10
3254 22
3254 40
Granulation: 100
Granulation: 220
Granulation: 400
3254 . .
Abrasive Bar, half-round
• Working area: 230 x 17 x 12 mm
3255 10
3255 22
3255 40
Granulation: 100
Granulation: 220
Granulation: 400
3255 . .
Assortment of Abrasive Bars
• Shapes: fl at, triangular, half round
• Granulation: 100, 220 and 400
3253 99
2 pieces 2 pieces
2 pieces
5 sheets
18 pieces (2 per granulation and shape)
230 x 280 mm
80 x 20 x 50 mm
E33
Diamond Tool Cleaner
Pencil shaped; a bundle of 1,500 fi nest steel wires guarantees
the cleaning of drill bits, millers and diamond drill bits. The grade
is adjustable.
Brass Cleaning Brush
• Core: Metal
• Bore Ø: Conical
Filing Brush
• Flat
• Coated surface: 105 mm
Marking Needle
• With hard metal tip
• Ball pen type
• Retracts for safety
• Black plastic grip to optimise the handling
• Spare tips available
Tips for Marking Needle
• Hard metal spare tips
Grinding Sponge Disc
• Granulation: 46
• Max. speed: 4,780 rpm
• Bore Ø: 8 mm
3506 00
50 mm 10 mm
3501 00 120 mm
3516 00
3426 10
100 mm 20 mm
2302 00 117 mm
2302 10 2 pieces
Graining Brush
• Core: Plastic
• Bore Ø: Conical
• Wire diameter: 0.6 mm
• Working speed: max. 2,800 rpm
To create a wood grain effect on acetate material.
3510 00 100 mm
25 g
260 g
250 x 35 mm
E34
Silver Palladium Wire
Only for use with spectacle frames with nickel
content, such as monel or German silver.
Material strength: 0.4 mm
Steel Wire
Only for use with stainless steel frames.
Material strength: 0.4 mm
Solder Dispenser
“Original Degussa”, for Degussa solder No. 3007 00.
Opening: 1.8 mm
3043 30 3043 10
2059 00
3043 20
20 g200 mm
1 x 50 cm
Titanium Wire
Only for use with titanium frames.
Material strength: 0.3 mm
1 x 50 cm 1 x 50 cm
Welding Wires for Laser or TIG Welding
Accessories for Soldering and Welding Units
Gas Cartridge
• For use with hand held solder unit
No. 2727 30 (discontinued)
• Butane gas
Oxygen Bottle
• For Micro Torch Set No. 2762 05 and
2762 00 (discontinued)
• Oxygen gas (no liquid gas)
Gas Cartridge
• For handheld soldering unit No. 2763 00
and Micro Torch Set No. 2762 05 and
2762 00 (discontinued)
• Liquid gas
• Burning duration: approx. 3.5 h
at low fl ame
2761 06 2737 01 2760 0270 ml 400 ml 13 g
This is not liquid gas.
The cartridge lasts for approx. 45 minutes.
Due to legal requirements gas and oxygen will be delivered
in separate packaging.
E35
3002 00white fl uid, fl ux included
Silver Solder, white fl uid
• For jewellery and frames
• To use without additional fl ux
• Metal contents: 56 % Ag
• Melting point: 650 °C
• Form: Paste in a dispensing cartridge
Braze Tec h 80 Flux
• For diffi cult to process materials, such as
stainless steel
• Leaves no residue on the soldered area
• Consistency: Paste
3114 00
Fluoron
• For high temperature soldering
• Consistency: Liquid
Braze Tec h Flux
• Consistency: Paste
3112 00
3112 05
3101 00
Heatstop
• Isolating paste for all types of soldering
• Prevents the distribution of heat in metal
• Consistency: Paste
3029 00
Electrolyte Flux
3198 00 800 ml 3199 01 1 l
100 g 100 ml
100 g
8 g
100 g
500 g
You will fi nd our soldering unit No. 2839 60
and further accessories on page A 36 to A 39.
If dried out, welding fl ux and heat stop can be sprayed
with distilled water.
E36
Hard Solder silver
Silver Solder Degussa 6002without Cd
Solder wire, white fl uid
Phantom Solder
Silver Solder Degussa 600 L 3
Bronze, nickel, stainless steel
60 % Ag without Cd
680 °C
3112 . . Braze Tec h
0.5 mm wire Ø
5 g
approx. 230 cm
3003 00 3007 00
Jewellery
60 % Ag without Cd
680 °C
3112 . . Braze Tec h
0.4 mm wire Ø in dispenser
2 g
approx. 110 cm
3010 003008 00
Field of application:
Metal contents:
Melting point:
Recommended Flux:
Form:
Sales unit:
Length:
For practice, also suitable
for nickel-free material
55 % Ag, Sn
660 °C
3112 . . Braze Tec h
0.5 mm wire Ø in dispenser
3 g
approx. 130 cm
All silver alloy over
800 ‰ fi neness
675 ‰ Au
710 °C
3112 . . Braze Tec h
0.4 mm wire Ø
3.5 g
approx. 230 cm
3014 00
Field of application:
Metal contents:
Melting point:
Recommended Flux:
Form:
Sales unit:
Length:
Jewellery
60 % Ag, 23 % Cu, 14.5 % Zn, 2.5 % Sn
680 °C
3112 . . Braze Tec h
0.5 mm wire Ø
5.3 g
approx. 280 cm
Field of application:
Metal contents:
Melting point:
Recommended Flux:
Form:
Sales unit:
Length:
Solder
E37
white fl uid, fl ux includedyellow fl uid, fl ux included
Gold Solder,8 Ct
Universal Solder,yellow fl uid
Universal Solder,white fl uid
gold fl uid, fl ux includedwhite fl uid, fl ux included
Pallarium – Universal Solder,white fl uid
Pallarium – Universal Solder,gold fl uid
Solder Wire,yellow fl uid
3016 00
Field of application:
Metal contents:
Melting point:
Recommended Flux:
Form:
Sales unit:
Length:
3020 03
Field of application:
Metal contents:
Melting point:
Recommended Flux:
Form:
Sales unit:
3022 03
All standard metals such as silver, nickel, chrome,
stainless steel, brass, etc.
40 % Ag
700 °C
Without fl ux
Tube 1 mm Ø
3 tubes at 150 mm each
3023 00 3023 01
Field of application:
Metal contents:
Melting point:
Recommended Flux:
Form:
Sales unit:
All standard metals such as nickel, silver, chrome,
stainless steel, gold, brass and others.
33 % Ag
580 °C
Without fl ux
Tube 1 mm Ø
12 rods at 150 mm each
Jewellery and metal frames
of gold alloy
333 ‰ Au
590 °C
3101 00 Fluoron
Wire 0.5 mm Ø
1 g
approx. 70 cm
All standard metals such as silver, nickel, chrome,
stainless steel, brass, etc.
50 % Ag
670 °C
Without fl ux
Tube 1 mm Ø
3 tubes at 150 mm each
All standard metals such as nickel, silver, chrome,
stainless steel, gold, brass and others
45 % Ag
580 °C
Without fl ux
Tube 1 mm Ø
12 rods at 150 mm each
3015 00
All standard metals such as silver, nickel, chrome,
stainless steel, brass, etc.
55 % Ag, 21 % Cu, 22 % Zn, 2 % Sn
660 °C
3101 00 Fluoron
Wire 0.4 mm Ø
5 g
approx. 75 cm