Configure WLAN AP
Transcript of Configure WLAN AP
7/21/2019 Configure WLAN AP
http://slidepdf.com/reader/full/configure-wlan-ap 1/42
Copyright © 2011, Juniper Networks, Inc. MP Overview 3
Configuring Mobility Points
Configuring Mobility Points
MP Overview
Figure 1–1. Example of a Juniper Network Topology
Configuring MP Access Points
MP-372
Router
Router
Wiredauthentication
client
System IP address10.10.10.4
MP-372
Port1
Port2
Port4
MX1
10.10.40.19 /24
10.10.20.19 /24
10.10.30.19 /24
RADIUS
servers
10.10.70.20
10.10.70.40
10.10.60.18/24
10.10.60.19 /24
RingMaster
Port3
MP-372
Layer 2
MP-372 System IP address10.10.40.4
MX2
Layer 2
MP-372
10.10.10.19 /24
System IP address10.10.50.4
MX3
Port5
VLANs on MX1
VLAN 2 mgmt, port 5, 10.10.10.4/24VLAN 4 blue, port 5, tag 20, 10.10.20.2/24VLAN 3 red, port 5, tag 30
Layer 2
serial-id 0322199998
serial-id 0322199999
serial-id 0322199997
serial-id 0322199996
serial-id 032219999510.10.50.19 /24
external antennamodel ANT-1060
7/21/2019 Configure WLAN AP
http://slidepdf.com/reader/full/configure-wlan-ap 2/42
4 MP Overview Copyright © 2011, Juniper Networks, Inc.
Network Address Translation (NAT) Support
Country of Operation
Directly Connected MPs and Distributed MPs
Informational Note:
Informational Note:
7/21/2019 Configure WLAN AP
http://slidepdf.com/reader/full/configure-wlan-ap 3/42
Copyright © 2011, Juniper Networks, Inc. MP Overview 5
Configuring Mobility Points
Distributed MP Network Requirements
−
−
−
−
7/21/2019 Configure WLAN AP
http://slidepdf.com/reader/full/configure-wlan-ap 4/42
6 MP Overview Copyright © 2011, Juniper Networks, Inc.
Distributed MPs and Spanning Tree Protocol (STP)
Distributed MPs and DHCP Option 43
ip:ip-addr1,ip-addr2,...
host:hostname1,hostname2,...
Informational Note:
Informational Note:
Informational Note:
7/21/2019 Configure WLAN AP
http://slidepdf.com/reader/full/configure-wlan-ap 5/42
Copyright © 2011, Juniper Networks, Inc. MP Overview 7
Configuring Mobility Points
Boot Process for Distributed MPs
MP Boot Descriptions
Example of an MP Booting over a Layer 2 Network
7/21/2019 Configure WLAN AP
http://slidepdf.com/reader/full/configure-wlan-ap 6/42
8 MP Overview Copyright © 2011, Juniper Networks, Inc.
Figure 1–2. An MP Booting over a Layer 2 Network
7/21/2019 Configure WLAN AP
http://slidepdf.com/reader/full/configure-wlan-ap 7/42
Copyright © 2011, Juniper Networks, Inc. MP Overview 9
Configuring Mobility Points
Example of an MP Booting over a Layer 3 Network
Figure 1–3. An MP Booting over a Layer 3 Network
7/21/2019 Configure WLAN AP
http://slidepdf.com/reader/full/configure-wlan-ap 8/42
10 MP Overview Copyright © 2011, Juniper Networks, Inc.
Example of a Dual-Home MP Booting on the NetworkMP
Figure 1–4. A Dual-Homed MP Booting on the Network
Example of an MP with a Static IP Configuration Booting on the NetworkMP
7/21/2019 Configure WLAN AP
http://slidepdf.com/reader/full/configure-wlan-ap 9/42
Copyright © 2011, Juniper Networks, Inc. MP Overview 11
Configuring Mobility Points
Figure 1–5. MP Booting with a Static IP Address
Loading and Activating Operational Images
7/21/2019 Configure WLAN AP
http://slidepdf.com/reader/full/configure-wlan-ap 10/42
12 MP Overview Copyright © 2011, Juniper Networks, Inc.
Forcing an MP To Download an Operational Image from the WLC
set ap apnum force-image-download {enable | disable}
MP Parameters
Table 1. Global MP Parameters
Parameter Default Value Description
7/21/2019 Configure WLAN AP
http://slidepdf.com/reader/full/configure-wlan-ap 11/42
Copyright © 2011, Juniper Networks, Inc. MP Overview 13
Configuring Mobility Points
Resiliency and Dual-Homing Options for MPs
Bias
Informational Note:
Table 1. Global MP Parameters (continued)
Parameter Default Value Description
7/21/2019 Configure WLAN AP
http://slidepdf.com/reader/full/configure-wlan-ap 12/42
7/21/2019 Configure WLAN AP
http://slidepdf.com/reader/full/configure-wlan-ap 13/42
Copyright © 2011, Juniper Networks, Inc. MP Overview 15
Configuring Mobility Points
Figure 1–8. Dual-Homed Direct and Distributed Connections to MX Switches
Dual-Homed Distributed Connections to MX Switches on Both MP Ports
Figure 1–9. Dual-homed Distributed Connections to MX Switches on Both MP Ports
Dual-Homed Distributed Connections to MX Switches on One MP Port
7/21/2019 Configure WLAN AP
http://slidepdf.com/reader/full/configure-wlan-ap 14/42
7/21/2019 Configure WLAN AP
http://slidepdf.com/reader/full/configure-wlan-ap 15/42
Copyright © 2011, Juniper Networks, Inc. MP Overview 17
Configuring Mobility Points
Note:
Table 2. Defaults for Service Profile Parameters (continued)
Parameter Default Value Radio Behavior When Parameter Set To Default Value
7/21/2019 Configure WLAN AP
http://slidepdf.com/reader/full/configure-wlan-ap 16/42
18 MP Overview Copyright © 2011, Juniper Networks, Inc.
Note:
Table 2. Defaults for Service Profile Parameters (continued)
Parameter Default Value Radio Behavior When Parameter Set To Default Value
7/21/2019 Configure WLAN AP
http://slidepdf.com/reader/full/configure-wlan-ap 17/42
Copyright © 2011, Juniper Networks, Inc. MP Overview 19
Configuring Mobility Points
Public and Private SSIDs
Encryption
Note:
Informational Note:
Informational Note:
Table 2. Defaults for Service Profile Parameters (continued)
Parameter Default Value Radio Behavior When Parameter Set To Default Value
7/21/2019 Configure WLAN AP
http://slidepdf.com/reader/full/configure-wlan-ap 18/42
20 MP Overview Copyright © 2011, Juniper Networks, Inc.
Mixed Cipher Support
WLC#set service-profile profile-name wpa-ie cipher-tkip enable
WLC# set service-profile profile-name rsn-ie [ciper-ccmp | cipher-tkip]
enable
WLC#set service-profile profile-name psk-phrase psk-phrase
WLC# set service-profile profile-name [rsn-ie | wpa-ie] auth-psk enable
Radio Profiles
Informational Note:
Informational Note:
Informational Note:
Table 3. Defaults for Radio Profile Parameters
Parameter Default Value Radio Behavior When Parameter Set To Default Value
7/21/2019 Configure WLAN AP
http://slidepdf.com/reader/full/configure-wlan-ap 19/42
Copyright © 2011, Juniper Networks, Inc. MP Overview 21
Configuring Mobility Points
RF Auto-Tuning
Default Radio Profile
Radio-Specific Parameters
Note:
Table 4. Radio-Specific Parameters
Parameter Default Value Description
Note:
Table 3. Defaults for Radio Profile Parameters (continued)
Parameter Default Value Radio Behavior When Parameter Set To Default Value
7/21/2019 Configure WLAN AP
http://slidepdf.com/reader/full/configure-wlan-ap 20/42
22 Configuring MPs Copyright © 2011, Juniper Networks, Inc.
Configuring MPs
Note:
Table 4. Radio-Specific Parameters (continued)
Parameter Default Value Description
7/21/2019 Configure WLAN AP
http://slidepdf.com/reader/full/configure-wlan-ap 21/42
Copyright © 2011, Juniper Networks, Inc. Configuring MPs 23
Configuring Mobility Points
Specifying the Country of Operation
set system countrycode code
Informational Note:
Table 5. Country Codes
Country Code
7/21/2019 Configure WLAN AP
http://slidepdf.com/reader/full/configure-wlan-ap 22/42
24 Configuring MPs Copyright © 2011, Juniper Networks, Inc.
Table 5. Country Codes (continued)
Country Code
7/21/2019 Configure WLAN AP
http://slidepdf.com/reader/full/configure-wlan-ap 23/42
Copyright © 2011, Juniper Networks, Inc. Configuring MPs 25
Configuring Mobility Points
show system
Table 5. Country Codes (continued)
Country Code
7/21/2019 Configure WLAN AP
http://slidepdf.com/reader/full/configure-wlan-ap 24/42
26 Configuring MPs Copyright © 2011, Juniper Networks, Inc.
WLC# set system countrycode US
success: change accepted.WLC# show system
===========================================================================
====
Product Name: WLC
System Name: WLC
System Countrycode: US
System Location:
System Contact:
System IP: 30.30.30.2
System idle timeout:3600
System MAC: 00:0B:0E:02:76:F6
===========================================================================
====
Boot Time: 2003-05-07 08:28:39
Uptime: 0 days 04:00:07
===========================================================================
====
Fan status: fan1 OK fan2 OK fan3 OK
Temperature: temp1 ok temp2 ok temp3 ok PSU Status: Lower Power Supply DC ok AC ok Upper Power
Supply missing
Memory: 115.09/496.04 (23%)
Total POE Draw [W] : 32.000
===========================================================================
Configuring an Auto-AP Profile for Automatic MP Configuration
Informational Note:
7/21/2019 Configure WLAN AP
http://slidepdf.com/reader/full/configure-wlan-ap 25/42
7/21/2019 Configure WLAN AP
http://slidepdf.com/reader/full/configure-wlan-ap 26/42
28 Configuring MPs Copyright © 2011, Juniper Networks, Inc.
Configured MPs Have Precedence Over Unconfigured MPs
Configuring an Auto-AP Profile
WLC# set ap auto
success: change accepted.
WLC# show ap config
Ap auto: mode: disabled bias: high
fingerprint
boot-download-enable: YES
force-image-download: NO
Radio 1: type: 802.11g, mode: enabled, channel: dynamic
tx pwr: 15, profile: default
auto-tune max-power: default
Radio 2: type: 802.11a, mode: enabled, channel: dynamic
tx pwr: 11, profile: default
auto-tune max-power: default
Table 7. Configurable Profile Parameters for Distributed MPs
Parameter Default Value
7/21/2019 Configure WLAN AP
http://slidepdf.com/reader/full/configure-wlan-ap 27/42
Copyright © 2011, Juniper Networks, Inc. Configuring MPs 29
Configuring Mobility Points
Changing MP Parameter Values
MP Parameters:
set ap auto bias {high | low}
set ap auto blink {enable | disable}
set ap auto force-image-download {enable | disable}
set ap auto group name
set ap auto mode {enable | disable}
set ap auto persistent [apnum | all]
set ap auto upgrade-firmware {enable | disable}
Radio Parameters:
set ap auto radiotype {11a | 11b| 11g}
set ap auto radio {1 | 2} auto-tune max-power power-level
set ap auto radio {1 | 2} mode {enable | disable}
set ap auto radio {1 | 2} radio-profile name mode {enable | disable}
Table 7. Configurable Profile Parameters for Distributed MPs (continued)
Parameter Default Value
7/21/2019 Configure WLAN AP
http://slidepdf.com/reader/full/configure-wlan-ap 28/42
30 Displaying Status Information for MPs Configured by the Auto-AP Profile Copyright © 2011, Juniper Networks, Inc.
Enabling the Auto-AP Profile
WLC# set ap auto mode enable
success: change accepted.
Specifying the Radio Profile Used by the Auto-AP Profile
set ap auto radio {1 | 2}
radio-profile profile-name mode {enable | disable}
WLC# set ap auto radio 1 radio-profile autodap1
success: change accepted.
Displaying Status Information for MPs Configured by the Auto-AP Profile
WLC# show ap status auto
AP: 7, AP model: MP-252, manufacturer Trapeze, name: MP07
====================================================
State: operational (not encrypted)
CPU info: IBM:PPC speed=266666664 Hz version=405GPr
id= ram=33554432
s/n=0333703027 hw_rev=A3
Uptime: 18 hours, 36 minutes, 27 seconds
Radio 1 type: 802.11g, state: configure succeed [Enabled] (802.11b
protect)
operational channel: 1 operational power: 14
base mac: 00:0b:0e:00:d2:c0
bssid1: 00:0b:0e:00:d2:c0, ssid: public
bssid2: 00:0b:0e:00:d2:c2, ssid: employee-net
bssid3: 00:0b:0e:00:d2:c4, ssid: mycorp-tkip
Radio 2 type: 802.11a, state: configure succeed [Enabled]
operational channel: 64 operational power: 14
base mac: 00:0b:0e:00:d2:c1
Informational Note:
7/21/2019 Configure WLAN AP
http://slidepdf.com/reader/full/configure-wlan-ap 29/42
Copyright © 2011, Juniper Networks, Inc. Displaying Status Information for MPs Configured by the Auto-AP Profile 31
Configuring Mobility Points
bssid1: 00:0b:0e:00:d2:c1, ssid: public
bssid2: 00:0b:0e:00:d2:c3, ssid: employee-net bssid3: 00:0b:0e:00:d2:c5, ssid: mycorp-tkip
Converting an MP Configured by the Auto-AP Profile into a Permanent MP
set ap auto persistent {apnum | all}
Configuring MP Port Parameters
Table 8. Maximum MPs Supported Per WLC
WLC Model Maximum That Can Be Configured Maximum That Can Be Booted
7/21/2019 Configure WLAN AP
http://slidepdf.com/reader/full/configure-wlan-ap 30/42
32 Displaying Status Information for MPs Configured by the Auto-AP Profile Copyright © 2011, Juniper Networks, Inc.
Configuring an MP
set ap apnum serial-id serial-ID
model {2330 | 2330A | 2330B| 2332-A1| AP-EASYA| AP1602 | AP1602C |
AP2750 | AP3750 | AP3850 | AP9551| MP-371 | MP-371B | MP-372 | MP-372A |
MP-372B| | MP-422 | MP-422A | MP-422B | MP-422FB| MP-422F| | MP-432 |
MP-432F| WLA522 | WLA-522E | MP-620 | MP-620A | Mp-620B| MP-622 | MP-71
|
MP-82|}
[radiotype {11ng | 11a | 11b| 11g | 11na}]
WLC# set ap 1 serial-id 0322199999 model MP-620
success: change accepted.
Configuring Static IP Addresses on Distributed MPs
Specifying IP Information
set ap apnum boot-configuration ip ip-addr netmask mask-addr gateway
gateway-addr [mode {enable | disable}]
WLC# set ap 1 boot-configuration ip 172.16.0.42 netmask 255.255.255.0
gateway 172.16.0.20 mode enable
success: change accepted.
Informational Note:
apnum
Informational Note:
7/21/2019 Configure WLAN AP
http://slidepdf.com/reader/full/configure-wlan-ap 31/42
Copyright © 2011, Juniper Networks, Inc. Displaying Status Information for MPs Configured by the Auto-AP Profile 33
Configuring Mobility Points
Specifying the WLC Information
set ap apnum boot-configuration [switch-ip ip-addr ] [name name dns
ip-addr ] [mode {enable | disable}]
WLC# set ap 1 boot-configuration switch-ip 172.16.0.21 mode enable
success: change accepted.
WLC# set ap 1 boot-configuration switch name mxr2 dns 172.16.0.1 mode
enable
success: change accepted.
Specifying VLAN information
set ap apnum boot-configuration vlan vlan-tag tag-value [mode {enable
disable}]
WLC# set ap 1 boot-configuration vlan vlan-tag 100 mode enable
success: change accepted.
Clearing an MP from the Configuration
clear port type port-list
Warning:
7/21/2019 Configure WLAN AP
http://slidepdf.com/reader/full/configure-wlan-ap 32/42
34 Displaying Status Information for MPs Configured by the Auto-AP Profile Copyright © 2011, Juniper Networks, Inc.
clear ap apnum
Changing MP Names
set ap apnum name name
Changing Bias
set ap apnum bias {high | sticky | low}
WLC# set ap 1 bias low
success: change accepted.
Disabling or Reenabling Automatic Firmware Upgrades
set ap apnum upgrade-firmware {enable | disable}
Enabling LED Blink Mode
set ap apnum blink {enable | disable}
Informational Note:
7/21/2019 Configure WLAN AP
http://slidepdf.com/reader/full/configure-wlan-ap 33/42
Copyright © 2011, Juniper Networks, Inc. Displaying Status Information for MPs Configured by the Auto-AP Profile 35
Configuring Mobility Points
Configuring AP LED Control
set ap apnum led-mode {auto | static | off}
auto
static
Configuring AP Communication Time Out
set ap apnum time-out seconds
Configuring MP-WLC Security
Encryption Key Fingerprint
RSA
a:aaaa:aaaa:aaaa:
aaaa:aaaa:aaaa:aaaa
Encryption Options
Informational Note:
Informational Note:
7/21/2019 Configure WLAN AP
http://slidepdf.com/reader/full/configure-wlan-ap 34/42
36 Displaying Status Information for MPs Configured by the Auto-AP Profile Copyright © 2011, Juniper Networks, Inc.
Verifying an MP Fingerprint on an WLC
set ap fingerprint
Finding the Fingerprint
show ap status
WLC# show ap status 8
AP: 7, AP model: MP-252, manufacturer Trapeze, name: MP07
fingerprint: b4:f9:2a:52:37:58:f4:d0:10:75:43:2f:45:c9:52:c3
====================================================
State: operational (not encrypted)
CPU info: IBM:PPC speed=266666664 Hz version=405GPr
id=0x29f1886d447f111a ram=33554432
s/n=0424000779 hw_rev=A3
Uptime: 1 hours, 8 minutes, 17 seconds
Radio 1 type: 802.11g, state: configure succeed [Enabled]
operational channel: 1 operational power: 1
Table 9. MP Security Requirements
MP Security
Setting
MP Has
Fingerprint?
Fingerprint Verified
in MSS?
MP Can Establish
Management Session with
WLC?
7/21/2019 Configure WLAN AP
http://slidepdf.com/reader/full/configure-wlan-ap 35/42
Copyright © 2011, Juniper Networks, Inc. Displaying Status Information for MPs Configured by the Auto-AP Profile 37
Configuring Mobility Points
base mac: 00:0b:0e:0a:60:00
bssid1: 00:0b:0e:0a:60:00, ssid: public bssid2: 00:0b:0e:0a:60:02, ssid: trapeze
Radio 2 type: 802.11a, state: configure succeed [Enabled]
operational channel: 48 operational power: 11
base mac: 00:0b:0e:0a:60:01
bssid1: 00:0b:0e:0a:60:01, ssid: public
bssid2: 00:0b:0e:0a:60:03, ssid: trapeze
Verifying a Fingerprint on the WLC
set ap apnum fingerprint hex
WLC# set ap 8 fingerprint
b4:f9:2a:52:37:58:f4:d0:10:75:43:2f:45:c9:52:c3
success: change accepted.
Setting the MP Security Requirement on an WLC
set ap security {require | optional | none}
The following command configures an WLC to require Distributed MPs to
have encryption keys:
Informational Note:
Informational Note:
7/21/2019 Configure WLAN AP
http://slidepdf.com/reader/full/configure-wlan-ap 36/42
38 MP-432 Support and 802.11n Configuration Copyright © 2011, Juniper Networks, Inc.
WLC# set ap security require
Fingerprint Log Message
AP-HS:(secure optional)configure AP 0335301065 with fingerprint
c6:98:9c:41:32:ab:37:09:7e:93:79:a4:ca:dc:ec:fb
MP-432 Support and 802.11n Configuration
PoE Requirements
Radio Type Data Rate
7/21/2019 Configure WLAN AP
http://slidepdf.com/reader/full/configure-wlan-ap 37/42
Copyright © 2011, Juniper Networks, Inc. MP-432 Support and 802.11n Configuration 39
Configuring Mobility Points
set ap <apnum> power-mode <auto | high>
Glossary of Terms for 802.11n
Configuration Commands
WLC2# set ap apnum port portnum model {2330 | 2330A | AP2750 | AP3750|AP3850 | MP-352 | MP-371 | MP-372 | MP-372-JP | MP-372A | MP-372-CN
|MP-372-JP | MP-422 | MP-422A | MP-422F| MP-432 | MP-620 | MP-620A |
MP-71} poe {enable | disable} radiotype {11a| 11b|11g | 11na|11ng}
Frame Aggregation Commands
WLC2# set service-profile profile-name 11n a-mpdu-max-length [8K|
16K| 32K| 64K] a-msdu-max-length [4K | 8K] frame-aggregation
[msdu|mpdu|all|disable]
{ mode-na|mode-ng [enable|disable| required]}
short-guard-interval [enable|disable]
Data Rate CommandsWLC2# set service-profile profile-name transmit-rates 11ng mandatory
{1.0|2.0|5.5|6.0|9.0|11.0|12.0|18.0|24.0|36.0|48.0|54.0|m0|m1|m2|m3|m
4|m5|m6|m7|m8|m9|m10|m11|m12|m13|m14|m15} beacon-rate <radio-rate>
disabled multicast-rate
{auto|1.0|2.0|5.5|6.018.0|24.0|36.0|48.0|54.0|
m0|m1|m2|m3|m4|m5|m6|m7|m8|m9|m10|m11|m12|m13|m14|m15}
Table 10. 802.11n Terms
Term Definition
Informational Note:
Informational Note:
Informational Note:
Informational Note:
7/21/2019 Configure WLAN AP
http://slidepdf.com/reader/full/configure-wlan-ap 38/42
40 Displaying MP Information Copyright © 2011, Juniper Networks, Inc.
WLC2# set service-profile profile-name transmit-rates 11na mandatory
{6.0|9.0|12.0|18.0|24.0|36.0|48.0|54.0|m0|m1|m2|m3|m4|m5|m6|m7|m8|m9|
m10| m11|m12|m13|m14|m15} beacon-rate <radio-rate> disabled multicast-rate
{auto|6.0|9.0|12.0|18.0|24.0|36.0|48.0|54.0|m0|m1|m2|m3|m4|m5|m6|m7|m
8|m9|m10|m11|m12|m13|m14|m15}
11n Channel Commands
WLC2# set radio-profile profile-name 11n channel-width-na {20MHz |
40MHz}
Displaying MP Information
Displaying MP Configuration Information
show ap config [apnum [radio {1 | 2}]]
WLC# show ap config 4
AP 4 (AP04)
Model: MP-422
Mode:
Bias: high
7/21/2019 Configure WLAN AP
http://slidepdf.com/reader/full/configure-wlan-ap 39/42
Copyright © 2011, Juniper Networks, Inc. Displaying MP Information 41
Configuring Mobility Points
Power mode: auto
Options: upgrade-firmwareConnection: network
Serial number: 0675200557
Fingerprint:
Communication timeout: 25
Location:
Contact:
Vlan-profile: default
Radio 1 (802.11g)
Mode: sentry Radio profile: defaultChannel: dynamic Load balancing: YES
Tx power: 22 Load balancing group:
Autotune max power: default Force rebalance: NO
Antenna location: indoors Antenna type: INTERNAL
Service profiles:
Snoop filters on radio: none
Snoop filters on radio profile: none
Radio 2 (802.11a)
Mode: enabled Radio profile: mirunaMeshOneChannel: 36 Load balancing: YES
Tx power: 5 Load balancing group:
Auto tune max power: default Force rebalance: NO
Antenna location: indoors Antenna type: INTERNAL
Service profiles:
mirunaMeshOne (Mesh)
Snoop filters on radio: none
Snoop filters on radio profile: none
Displaying Connection Information for Distributed MPs
show ap global [apnum | serial-id serial-ID ]
Informational Note:
7/21/2019 Configure WLAN AP
http://slidepdf.com/reader/full/configure-wlan-ap 40/42
42 Displaying MP Information Copyright © 2011, Juniper Networks, Inc.
WLC# show ap global
Total number of entries: 8
AP Serial Id WLC IP Address Bias
--- ----------- --------------- ----
1 11223344 10.3.8.111 HIGH
- 11223344 10.4.3.2 LOW
2 332211 10.3.8.111 LOW
- 332211 10.4.3.2 HIGH
17 0322100185 10.3.8.111 HIGH
- 0322100185 10.4.3.2 LOW
18 0321500120 10.3.8.111 LOW
- 0321500120 10.4.3.2 HIGH
Displaying a List of Unconfigured Distributed MPs
show ap unconfigured
WLC# show ap unconfigured
Total number of entries: 1
Serial Id: 0333001287 Model: MP-422 IP Address: 10.2.2.1.1
Port: 5 Vlan: DAP Reason: No configuration
Informational Note:
7/21/2019 Configure WLAN AP
http://slidepdf.com/reader/full/configure-wlan-ap 41/42
Copyright © 2011, Juniper Networks, Inc. Displaying MP Information 43
Configuring Mobility Points
Displaying Active Connection Information for Distributed MPs
show ap connection [apnum | serial-id serial-ID]
7/21/2019 Configure WLAN AP
http://slidepdf.com/reader/full/configure-wlan-ap 42/42