4 - CONFIGURATION OF THE SERVICE PC

4-50LCT V5.0 - OMN

911-360/02A0500 - Issue 1, November 2003

4.2.3 Configuration of the dial-up connection in Windows XP

For the configuration of the dial-up connection, the following operations are required:

– installation of the direct connection via cable

– creation and configuration of the dial-up connection with the radio equipment

– configuration of the TCP/IP protocol.

4.2.3.1 Installation of the direct connection via cable

– In Control Panel click twice on Phone and Modem Options (Fig. 4.81). The

system displays the Phone and Modem Options window (Fig. 4.82). Select

Modems and then click on Add.

– The window Add Hardware Wizard - Install New Modem is displayed (Fig. 4.83).

Select the Don't detect my modem; I will select it from a list and click on Next.

– The window of Fig. 4.84 is displayed; click on Have Disk.

– The window of Fig. 4.85 is displayed. Insert the installation floppy-disk/CD-ROM

and click on Browse.

– The window Locate File is displayed (Fig. 4.86).

Select the drive of the installation floppy-disk/CD-ROM and search the directory

containing the “mdmitv01.inf” file; click on Open.

– The window of Fig. 4.87 is displayed again. Click on OK to copy the “mdmitv01.inf”

file.

– The window of Fig. 4.88 is displayed; click on Next to continue.

– The window of Fig. 4.89 is displayed. Select the communication port (usually: COM

1) and click on Next to continue.

– The window of Fig. 4.90 is displayed. click on Continue Anyway to continue.

– The window of Fig. 4.91 is displayed.

Click on Finish to end the installation procedure for direct connection.

– The window of Fig. 4.92 is displayed where Radio Equipment Windows NT

Direct Connection appears in the list of installed modems. Click on OK to end and

exit.

Under Windows XP the following software components must be installed on the

service PC:

– TCP/IP communication protocol.

Otherwise the software must be installed using the Windows XP CD-ROM.

The “mdmitv01.inf” file is on CD-ROM. In case of installation from floppy-disk, it

is necessary to copy the file on a floppy-disk..

4 - CONFIGURATION OF THE SERVICE PC

4-51LCT V5.0 - OMN

911-360/02A0500 - Issue 1, November 2003

Fig. 4.81 Installation of the direct connection in Windows XP (1/12)

Fig. 4.82 Installation of the direct connection in Windows XP (2/12)

4 - CONFIGURATION OF THE SERVICE PC

4-52LCT V5.0 - OMN

911-360/02A0500 - Issue 1, November 2003

Fig. 4.83 Installation of the direct connection in Windows XP (3/12)

Fig. 4.84 Installation of the direct connection in Windows XP (4/12)

Fig. 4.85 Installation of the direct connection in Windows XP (5/12)

4 - CONFIGURATION OF THE SERVICE PC

4-53LCT V5.0 - OMN

911-360/02A0500 - Issue 1, November 2003

Fig. 4.86 Installation of the direct connection in Windows XP (6/12)

Fig. 4.87 Installation of the direct connection in Windows XP (7/12)

Fig. 4.88 Installation of the direct connection in Windows XP (8/12)

4 - CONFIGURATION OF THE SERVICE PC

4-54LCT V5.0 - OMN

911-360/02A0500 - Issue 1, November 2003

Fig. 4.89 Installation of the direct connection in Windows XP (9/12)

Fig. 4.90 Installation of the direct connection in Windows XP (10/12)

Fig. 4.91 Installation of the direct connection in Windows XP (11/12)

4 - CONFIGURATION OF THE SERVICE PC

4-55LCT V5.0 - OMN

911-360/02A0500 - Issue 1, November 2003

Fig. 4.92 Installation of the direct connection in Windows XP (12/12)

4.2.3.2 Creation and configuration of the dial-up connection

– Click on Start and select: Settings → Network Connections. The system

displays the Network Connections window (Fig. 4.93). Select Create a New

Connection option.

– The system displays the New Connection Wizard window (Fig. 4.94). Click on

Next to continue.

– The system displays the window shown in Fig. 4.95. Select the Set up an

advanced connection option. Click on Next to continue.

– The system displays the window shown in Fig. 4.96. Select the Connect directly

to another computer option. Click on Next to continue.

– The system displays the window shown in Fig. 4.97. Select the Guest option. Click

on Next to continue.

– The system displays the window for the name selection of the connection

(Fig. 4.98). Type the name and click on Next to continue.

– The system displays the equipment selection window (Fig. 4.99).

– Select the Radio Equipment Windows NT Direct Connection option

(Fig. 4.100). Click on Next to continue.

– The system displays the window shown in Fig. 4.101. Click on Finish to complete

and to exit.

– In Control Panel, click twice on Phone and Modem Options (Fig. 4.102).

– The system displays the Phone and Modem Options window (Fig. 4.103). Select

Modems and then click on Properties.

– The system displays the window shown in Fig. 4.104. Click on Advanced

(Fig. 4.105) and then on Change Default References.

– The system displays the window shown in Fig. 4.106. Set the properties of the

connection as pointed out into the figure. Click on Advanced.

4 - CONFIGURATION OF THE SERVICE PC

4-56LCT V5.0 - OMN

911-360/02A0500 - Issue 1, November 2003

– The system displays the window shown in Fig. 4.107. Set the properties of the

connection as pointed out into the figure.

– Click on OK to end and confirm the settings. To close all the currently open

windows.

Fig. 4.93 Creation and configuration of the dial-up connection in Windows XP (1/15)

Fig. 4.94 Creation and configuration of the dial-up connection in Windows XP (2/15)

For the connection to the new equipment (as SRA 4, SRAL XD or MicroHop), it is

necessary to select 38400 as bit rate for the port.

4 - CONFIGURATION OF THE SERVICE PC

4-57LCT V5.0 - OMN

911-360/02A0500 - Issue 1, November 2003

Fig. 4.95 Creation and configuration of the dial-up connection in Windows XP (3/15)

Fig. 4.96 Creation and configuration of the dial-up connection in Windows XP (4/15)

Fig. 4.97 Creation and configuration of the dial-up connection in Windows XP (5/15)

4 - CONFIGURATION OF THE SERVICE PC

4-58LCT V5.0 - OMN

911-360/02A0500 - Issue 1, November 2003

Fig. 4.98 Creation and configuration of the dial-up connection in Windows XP (6/15)

Fig. 4.99 Creation and configuration of the dial-up connection in Windows XP (7/15)

Fig. 4.100 Creation and configuration of the dial-up connection in Windows XP (8/15)

4 - CONFIGURATION OF THE SERVICE PC

4-59LCT V5.0 - OMN

911-360/02A0500 - Issue 1, November 2003

Fig. 4.101 Creation and configuration of the dial-up connection in Windows XP (9/15)

Fig. 4.102 Creation and configuration of the dial-up connection in Windows XP (10/15)

4 - CONFIGURATION OF THE SERVICE PC

4-60LCT V5.0 - OMN

911-360/02A0500 - Issue 1, November 2003

Fig. 4.103 Creation and configuration of the dial-up connection in Windows XP (11/15)

Fig. 4.104 Creation and configuration of the dial-up connection in Windows XP (12/15)

4 - CONFIGURATION OF THE SERVICE PC

4-61LCT V5.0 - OMN

911-360/02A0500 - Issue 1, November 2003

Fig. 4.105 Creation and configuration of the dial-up connection in Windows XP (13/15)

Fig. 4.106 Creation and configuration of the dial-up connection in Windows XP (14/15)

For the connection to SRA 4, SRAL XD or MicroHop, set 38400.

4 - CONFIGURATION OF THE SERVICE PC

4-62LCT V5.0 - OMN

911-360/02A0500 - Issue 1, November 2003

Fig. 4.107 Creation and configuration of the dial-up connection in Windows XP (15/15)

4.3 Configuration of the Connection to LAN on

Ethernet Interface

The only operation required on the service PC is the TCP/IP protocol configuration for

the Ethernet NIC.

Under Windows, the Server PC must be equipped with the following software

components:

– Ethernet NIC and corresponding driver

– TCP/IP communication protocol.

Otherwise the software must be installed using the Windows CD-ROM and/or the

floppy-disk/CD-ROM with drivers for the NIC.

In case of connection via router, refer to the corresponding manual for the

operations on the router itself.

In case of connection through DualQ-Adapter, for the operations to be executed

on the DualQ-Adapter, refer to the relevant OMN Manual.