Compressors for CAD/CAM milling systems -...
Transcript of Compressors for CAD/CAM milling systems -...
METASYS Medizintechnik GmbH | Florianistraße 3, 6063 Rum bei Innsbruck, Austria | Phone: +43 512 205420 | [email protected] | www.metasys.com
META CAM compressors
Conventional dental compressors within the standard pressure range of 5 to 7 bar are unable to satisfy the requirements of many dental milling machines. However, CAD/CAM milling systems require an operating pressure of up to 10 bar, in order to guarantee safety with a tool change for example. META CAM compressors have been designed specially for such systems, because they guarantee a pressure range of 8 to 10 bar in continuous operation. Equipped with membrane drying and a double filtering process, they ensure the supply of oil-free, dry and perfectly hygienic compressed air, which is decisive for the quality of the end products. The right compressor for many of the CAD/CAM systems available on the market can be found on the basis of the respective requirements profile (performance and output) of the milling system. All META CAM compressors are also available with a cover, to ensure quiet operation. In this way it is possible to reduce the noise level to 54 dB(A).
Compressors for CAD/CAM milling systems
Guarantee periodThe guarantee period for compressors is 12 months. If the prescribed “one-year maintenance” or the „3000 hours maintenance” works are performed, the guarantee period can be extended by 1 year, although by no more than 2 years in all. The maximum possible guarantee period is therefore 3 years.
Maintenance intervalsThe maintenance intervals are binding and must be adhered to. The following maintenance work is prescribed: the annual filter cartridge change (“filter cartridge replacement kit”) and the „3000 h kit + valve block” (compressor-dependent). Maintenance works performed must be documented in the device document (part of the installation, operating and maintenance instructions). METASYS reserves the right to inspect the maintenance records.
Optional sound proofing coverThe majority of META CAM compressors are optionally
available with a sound proofing cover.
High pressure range up to 10 barMETA CAM compressors operate within a pressure range of 7 to 10 bar
High quality components in the unitsMETA CAM units are equipped with specific components, in order to counter the loads within the high pressure range.
The right choiceWe are happy to assist you in choosing the right META CAM
compressor for your specific milling or grinding machine. You can find further information at www.metasys.com.
Flyer CAD/CAM EN 2017-03 70010061 ZK-55.332/00 Subject to printing and setting errors!
Tank capacity: 40 l
Dimensions: 770 x 710 x 410 mm
Weight: 50 kg
Noise level: 67 dB(A) / 54 dB(A)*
META CAM 150
Amann Girrbach ceramill® motion 2
Amann Girrbach ceramill® mikro
Planmeca PlanMill® 40
Planmeca PlanMill® 50
Sirona inLab MC X5
VHF CAM 5-S2 Impression
VHF CAM 4-K4 Impression
imes-icore CORiTEC 140i
imes-icore CORiTEC 245i
imes-icore CORiTEC 250i
...
META CAM 250
Wieland Zenotec® mini
Wieland Zenotec® select hybrid
Zirkonzahn Kompaktlinie M1
Zirkonzahn M3
Zirkonzahn M4 Wet Heavy Metal
Zirkonzahn M5 Heavy Metal
Zirkonzahn M6 Wet Heavy Metal
...
META CAM 450
Wieland Zenotec® select ion
...
META CAM 650
KaVo ARCTICA Engine
KaVo Everest Engine
...
*with noise insulation cover
Tank capacity: 40 l
Dimensions: 810 x 710 x 410 mm
Weight: 58 kg
Noise level: 65 dB(A) / 54 dB(A)*
Tank capacity: 90 l
Dimensions: 820 x 1100 x 630 mm
Weight: 118 kg
Noise level: 70 dB(A) / 56 dB(A)*
Suitable for
Tank capacity: 200 l
Dimensions: 900 x 1450 x 820 mm
Weight: 183 kg
Noise level: 72 dB(A)
Suitable for
Suitable for
Suitable for
META CAM compressorsThe right compressor for the milling machine
A compressed air requirement assessment must be carried out prior to selecting a META CAM compressor or the selection must be validated in conjunction with the milling machine following installation.