Compact Metric Cylinders

3

Metric Bimba Flat-1 Series

©1997 Bimba Manufacturing Company All Rights Reserved Printed in U.S.A.

Space savings without sacrificing quality means better performance and longer cylinder life.Flat-1 offers these quality features:

BIMBA Flat-1 cylinders were designed with space savings in mind.Five models offer five ways to save space.

• Flat-1, the original round cylinder

• Square Flat-1, for additional mounting variations

• Flat-II, the round, dual piston rod, nonrotating cylinder

• Square Flat-II, the square, dual piston rod, nonrotating cylinder

• FM2/FM3/FM4 for two, three, or four times the forcein a single cylinder

• FMP for three positions

• 4301 stainless steel (X5 CrNi 18.9) cylinder body with a mirror finish I.D.Stainless steel fights corrosion andscoring from dirt particles. The result islonger piston seal life.

• Oil impregnated bronze rod bushing isstandard in all models. No sacrifice ofbushing length to save space.

• Ground and polished 4305 stainless steel(X12 CrNi 18.8) piston rod.

• High strength piston to rod connection.

• Precision machined, anodized aluminumalloy heads.

BIMBA FLAT-1 FITS RIGHT IN!

4305 stainless steelpiston rod

Anodizedaluminum alloyheads

Oil impregnatedbronze rod bushing

Buna N "O" ringrod seal

4301 stainless steelcylinder body

Buna N "O" ringpiston seal

Approximate Power Factors(For all models except FM2, FM3, FM4)

14mm = 15 N/bar19mm = 28 N/bar27mm = 57 N/bar38mm = 113 N/bar50mm = 196 N/bar63mm = 311 N/bar76mm = 453 N/bar

101mm = 801 N/bar

For example, a 14mm boremodel FM-0225 will exert a forceof approximately 75N when thesupply pressure is 5 bar.

▼▼

▼

▼▼

▼

4

Bimba Flat-1 Series Metric

Model FM(Double Acting, Single End Rod)

Standard strokes3.2mm, 5, 10, 15, 20, 25, 30,40, 50, 80, 100mm

Model FMD(Double Acting, Double End Rod)

Standard strokes3.2mm, 5, 10, 15, 20, 25,30, 40, 50, 80, 100mm

Basic Models

Model FMS(Single Acting, Spring Return, Rod Normally Retracted)

Standard strokes3.2mm, 5, 10, 15, 20, 25, 30,40, 50mm

Model FMR(Reverse Acting, Spring Return, Rod Normally Extended)

Standard strokes3.2mm, 5, 10, 15, 20, 25, 30,40, 50mm

Ba + STROKE

F

K

3.2

DIA.ROD

TYP.

TYP.J

1

E

DD CLEARHOLES FORD SOCKET HEADCAP SCREW

C BOLTCIRCLE

L PORT AH

2

3

4LOCATION OF MTG. HOLES14mm BORE ONLY

Bb + STROKE

3.2

TYP.J

3.2 +STROKE

KTYP.

F DIA.ROD

LOCATION OF MTG. HOLES14mm BORE ONLY

DD CLEARHOLES FORD SOCKETHEAD CAPSCREW

1

E

C BOLTCIRCLE

L PORT AH

2

3

4

BC + STROKE

F

K

3.2

DIA.ROD

TYP.

TYP.J



1

E

C BOLTCIRCLE

L PORT AH

2

3

4

Bd + STROKE

3.2 +STROKE

F DIA.ROD

KTYP.

TYP.J



1

E

C BOLTCIRCLE

L PORT AH

2

3

4

Contact Distributor for price and dimensions over 50mm stroke. See page 8 for spring forces.

Contact Distributor for price and dimensions over 50mm stroke. See page 8 for spring forces.

5


Bore A Ba* Bb*Bc* Bd*

C DD D E Std.0-25mm 26-50mm 0-25mm 26-55mm

14mm (02) 28.5 14.3 17.4 20.6 34.9 27.0 41.3 22.5 2 M3 M4

19mm (04) 38.0 14.3 17.4 20.6 34.9 27.0 41.3 31.0 4 M3 M5

27mm (09) 50.6 22.2 23.8 22.2 38.1 34.9 50.8 43.0 4 M3 M8

38mm (17) 66.4 22.2 25.4 22.2 38.1 34.9 50.8 56.0 4 M5 M10

50mm (31) 79.1 23.8 27.0 23.8 39.7 36.5 52.4 68.0 4 M5 M12

63mm (50) 95.0 30.2 33.3 30.2 52.4 49.2 88.9 83.0 4 M6 M12

76mm (70) 107.7 31.8 34.9 31.8 54.0 50.8 73.0 96.0 4 M6 M16

101mm (125) 139.5 39.7 42.9 39.7 61.9 58.7 81.0 125.0 4 M8 M20

Bore E Fine E Depth F H J K L

14mm (02) M4x0.5 11.7 6.3 5.5 8.7 3.6 M5

19mm (04) M5x0.5 11.7 7.9 6.0 8.7 3.6 M5

27mm (09) M8x1.0 17.8 12.7 11.0 12.7 6.4 G 1/8

38mm (17) M10x1.25 17.8 15.9 12.0 12.7 6.4 G 1/8

50mm (31) M12x1.25 17.8 19.1 16.0 13.5 6.4 G 1/8

63mm (50) M12x1.25 17.8 19.1 16.0 16.7 8.3 G 1/8

76mm (70) M16x1.5 18.5 22.2 19.0 17.5 8.3 G 1/8

101mm (125) M20x1.5 20.3 25.4 22.0 21.4 10.7 G 1/4

Dimensions(mm)(Basic Model)

*See page 7 for length adders for options.

6


Mounting OptionsTrunnion Mount(rear or front)(-2F shown)Not available in 14mm bore.

Pivot Mount(-1 shown)Complete with bronze pivot bushing.Not available as an accessory.

N

P

M

P

TYP.90º

THREADEDD-DR HOLES

BOLT CIRCLECLOCATION OF MTG. HOLES14mm BORE ONLY

X

*

90°TYP.

4 THREADEDR HOLES

C BOLTCIRCLE

Threaded Mounting Holes(available either or both ends)(-3R shown)14mm Bore 19mm Bore and larger

Screw Clearance Holes(available either or both ends)(-4R shown)

AAAF

AE

3.2

AC

AB

AD

Nose Mount(available in FM, FMS, FMR)(-5 shown)Includes heavy duty rear head; see page 7

*43º-19mm Bore only 45º-all other bores

7


Bore AA AB AC AD AE AF

14mm (02) 1.52 24 Hex 9.65 M16 x 1.5 6g 12.70 6

19mm (04) 1.52 32 Hex 9.65 M22 x 1.5 6g 15.75 6

27mm (09) 3.30 46 Hex 19.05 M30 x 1.5 6g 25.40 8

38mm (17) 3.30 60 Hex 19.05 M38 x 1.5 6g 31.75 10

50mm (31) 4.83 70 Hex 22.35 M45 x 1.5 6g 35.05 10

63mm (50) 6.35 70 Hex 25.40 M45 x 1.5 6g 35.05 10

76mm (70) 6.35 80 Hex 25.40 M52 x 1.5 6g 35.05 12

101mm (125) 4.83 80 Hex 28.45 M52 x 1.5 6g 44.45 12

Bore M N P Q R S T U W X Y Z

14mm (02) N/A N/A N/A 5 M3 9.5 5 6.5 19 4.6 16 5

19mm (04) 8 3 4.5 5 M3 9.5 5 6.5 19 6 19 5

27mm (09) 13 6 6.5 5 M3 9.5 6.5 6.5 20.5 6 19 5

38mm (17) 13 6 6.5 10 M5 19 6.5 11.5 30 9 35 9.5

50mm (31) 13 6 6.5 10 M5 19 8 11 32 9 35 9.5

63mm (50) 16 8 8.5 10 M6 19 9.5 11 33.5 10.5 35 9.5

76mm (70) 16 8 8.5 16 M6 25.5 9.5 14 43 10.5 47.5 9.5

101mm (125) 19 10 10.5 16 M8 25.5 11 14.5 44.5 13.5 47.5 9.5

Bore

Length Adder

Low FrictionSeals (L)

Heavy DutyRear Head* (HD)

Magnetic Position Sensing**

FM, FMD FMS FMR

14mm (02) 6.4 3.2 22.2 15.9 9.5

19mm (04) 6.4 3.2 22.2 22.2 22.2

27mm (09) 9.5 4.8 22.2 22.2 22.2

38mm (17) 9.5 4.8 22.2 22.2 22.2

50mm (31) 9.5 4.8 22.2 22.2 22.2

63mm (50) 9.5 6.4 22.2 22.2 22.2

76mm (70) 12.7 6.4 22.2 22.2 22.2

101mm (125) 12.7 9.5 22.2 22.2 22.2

Dimensions(mm)(Nose Mount)

(Dimensional variations from standard as shown.)

(Mounting Options)

*Heavy duty rear head isrecommended for applicationswhere the cylinder is mounted onthe front face or trunnion-mounted, and impact loading (20or more cycles per minute)occurs between the piston andrear head. It increases the overalllength of the cylinder as shown.

**A minimum stroke of 9.5mm isrequired to sense extending end-of-stroke position. For lowfriction seals used in conjunctionwith magnetic position sensing,use M length adder only.

Options

NOTE: Exceedingrecommended torquemay cause mountingthreads to shear.

Bore Maximum Torque

14mm (02) 16

19mm (04) 38

27mm (09) 136

38mm (17) 163

50mm (31) 176

63mm (50) 176

76mm (70) 176

101mm (125) 203

Maximum Torque Recommendations (N-m)

8


Enclosed Spring Forces

FMD Hollow Rods (Option H)

Male Rod Ends (Option MT or MTF)Rod Wiper (Option W)

Options(mm)

4.8

9.5

WD

ETHREAD

LG

Bore WD

14mm (02) 14.3

19mm (04) 17.5

27mm (09) 22.2

38mm (17) 25.4

50mm (31) 63mm (50) 28.6

76mm (70) 31.8

101mm (125) 34.9

BoreE

LGMT MTF

14mm (02) M4 M4 x 0.5 10

19mm (04) M5 M5 x 0.5 10

27mm (09) M8 M8 x 1.0 12

38mm (17) M10 M10 x 1.25 12

50mm (31) 63mm (50) M12 M12 x 1.25 16

76mm (70) M16 M16 x 1.5 20

101mm (125) M20 M20 x 1.5 20

BoreHole Diameter

FemaleRod Threads

MaleRod Threads

14mm (02) 3.2 N/A

19mm (04) 3.6 2.4

27mm (09) 5.6 4.0

38mm (17) 7.1 4.8

50mm (31) 63mm (50) 9.5 6.4

76mm (70) 11.1 7.9

101mm (125) 12.7 9.5

BoreMaximum

Load

Spring Rate

1-25mm stroke

26-50mm stroke

14mm (02) 25N .74 N/mm .30 N/mm

19mm (04) 45N 1.05 N/mm .44 N/mm

27mm (09) 50N 1.05 N/mm .44 N/mm

38mm (17) 50mm (31) 57N .95 N/mm .39 N/mm

63mm (50) 76mm (70)

101mm (125) 110N 1.13 N/mm .48 N/mm

9


• Body — 4301 Stainless Steel

• Heads — Anodized Aluminum Alloy

• Piston Rod — Ground and Polished 4305 Stainless Steel

• Seals — Buna N (High temperature seals optional)

• Rod Bushing — Oil Impregnated Bronze

• Spring Forces — See Page 8

• Pressure Rating — 14 Bar Maximum (Air only)

• Temperature Rating — From -25°C to +65°C

Buna N seals with a temperature range of -25°C to +65°C are standard in all Bimba air cylinders. Fluoroelastomer seals rated forhigher temperature applications are available. If cylinders are oper-ated below -18°C for extended time periods, special modificationsmay be required. Special seal materials are available upon request.

How to OrderThe Model Number for all Flat-1 cylinders consists of three alphanumeric clusters. These designate type,bore size and stroke length, and mounting and special options. Please refer to the charts below for anexample of Model Number FM-1715-3V. This is a double acting, 38mm bore, 15mm stroke cylinder withthreaded mounting holes both ends and high temperature option.

FM - Double Acting, Single End RodFMD - Double Acting, Double End RodFMR - Reverse ActingFMS - Single Acting

02 - 14mm 31 - 50mm04 - 19mm 50 - 63mm09 - 27mm 70 - 76mm17 - 38mm 125 - 101mm

5 - 5mm40 - 40mm

100 - 100mmETC.

No Number - Basic model1 - Pivot mount

1N - Pivot mount 90° from standard2F* - Front trunnion mount2R* - Rear trunnion mount

3 - Threaded mounting holes, both ends3F - Threaded mounting holes, front3R - Threaded mounting holes, rear

4 - Screw clearance holes, both ends4F - Screw clearance holes, front4R - Screw clearance holes, rear

5 - Nose Mount**

*Not available in 14mm bore.**Available in FM, FMS and FMR models. Includes heavyduty rear head.

FTF - Fine female thread (see page 5)H - Hollow rod (double end models

only) (see page 8)HD - Heavy duty rear head (see page 7)

G - Magnalube® GMT - Male rod end (coarse thread) (see page 8)

MTF - Male rod end (fine thread) (see page 8)NT - Non-threaded rod

P2*, P3, P4* - Front port position #2, etc. (see page 4)L - Low friction seals (see page 7)

M, M1, M3, M4 - Magnetic position sensing (see page78)1

T1, T3, T4 - Additional switch mounting post located in position #1, 3 or 4

V - High temperature option (-18 to +205°C)W - Rod wiper (Buna N only) (see page 8)

Y - Moly-coat (MoS2 I.D. coating)

EE10 - 10mm extra rod extension, etc.EE50 - 50mm extra rod extension, etc.

*Not available in 14mm bore1 If magnetic position sensing is specified with Fluoroelastomer Seals, standard Buna-N based magnet will be provided. Magneticposition sensing is not reliable above 50°C.

(Enter in alphabetical order, except EE which is last)(Enter in numeric order)

FM-1715-3V

BORE SIZETYPE

OPTIONSMOUNTING OPTIONS

STROKE LENGTH

Magnalube® is a trademark of Carleton-Stuart Company.

10


Bore

Approximate Cylinder Weights (gms)

FM, FMS FMD FMR Nose Mount option

BaseAdder

per 5mm of stroke

BaseAdder

per 5mm of stroke

Adder per 5mm of

stroke for -H option

BaseAdder

per 5mm of stroke

Adder to base weight

14mm (02) 34 3.6 37 6.8 4.4 36.9 3.6 5

19mm (04) 54 4.4 60 9 6.8 56.7 4.4 10

27mm (09) 139 13.4 164 17.8 13.4 150.3 13.4 40

38mm (17) 272 17.8 318 26.7 22.3 297.7 17.8 70

50mm (31) 369 22.3 431 31.1 26.7 396.9 22.3 120

63mm (50) 635 26.7 794 35.5 31.1 708.7 26.7 130

76mm (70) 819 35.5 1077 49 40.1 921.4 35.5 180

101mm (125) 1579 44.6 2036 58 49 1752.0 44.6 210

Weights

Repair Parts

Basic Repair Kit (K-B-FO)*

Part No. Description Quantity

PF-1 Rod Seal 1

PF-2 Piston Seal 1

PF-3 Tube Seal 2

PF-4 Bushing 2

Wiper Option Basic Repair Kit (K-B-FO-W)*


PF-1 Rod Seal 1

PF-2 Piston Seal 1

PF-3 Tube Seal 2

PF-4 Bushing 1

PF-5 Wiper Bushing 1

PF-6 Wiper 1

Basic Repair Kit (K-B-FOD)*


PF-1 Rod Seal 2

PF-2 Piston Seal 1

PF-3 Tube Seal 2

PF-4 Bushing 2

Wiper Option Basic Repair Kit (K-B-FOD-W)*


PF-1 Rod Seal 2

PF-2 Piston Seal 1

PF-3 Tube Seal 2


PF-6 Wiper 2

*Must specify bore size when ordered. Contact your localBIMBA Distributor for pricing on kits and other repair parts.

Single End Rod Kits for Nose Mount Option

Basic Repair Kit (K-B-FO-N)


PF-1 Rod Seal 1

PF-2 Piston Seal 1

PF-3 Tube Seal 2

PF-4 Bushing 2

Wiper

D-63632 14mm (02) 1

D-63633 19mm (04) 1

D-63634 27mm (09) 1

D-63635 38mm (17) 1

D-63636 50mm (31), 63mm (50) 1

D-63637 76mm (70) 1

D-63638 101mm (125) 1

Mounting Nuts

Bore Part No.

14mm (02) D-62752

19mm (04) D-62753

27mm (09) D-62754

38mm (17) D-62755

50mm (31) D-62756

63mm (50) D-62756

76mm (70) D-62785

101mm (125) D-62785

Double End Rod KitsSingle End Rod Kits

11

Metric Bimba Square Flat-1 Series

The convenient alternative for horizontal and side mounting, with provisionsfor both a bottom flush or face mounting. The Square Flat-1 also minimizesthe centerline distance when cylinders are mounted side-by-side.






• Tie Rods — 4305 Stainless Steel

• Spring Forces — See Page 15

• Pressure Rating — Bore Sizes 19mm-50mm 14 Bar Maximum (Air only) Bore Sizes 63mm-101mm 10.34 Bar Maximum (Air only)

• Temperature Rating — From -25°C to +65°C. Buna N seals with atemperature range of -25°C to +65°C are standard in all Bimba aircylinders. Fluoroelastomer seals rated for higher temperature applica-tions are available. If cylinders are operated below -18°C for extendedtime periods, special modifications may be required. Special sealmaterials are available upon request.

50 - 63mm70 - 76mm125 - 101mm

The Model Number for all Square Flat-1 cylinders consists of three alphanumeric clusters. These designate type,bore size and stroke length, and options. Please refer to the charts below for an example of Model NumberFSMS-7040-V. This is a single acting, 76mm bore, 40mm stroke cylinder with high temperature option.

How to Order

FTF - Fine female thread (see page 13)G - Magnalube® GH - Hollow rod (double end models only)

(see page 15)L - Low friction seals (see page 14)

M, M1, M4 - Magnetic position sensing (see page 78)1

MT - Male rod end (coarse thread) (see page 14)MTF - Male rod end (fine thread) (see page 14)

NT - Non-threaded rodT1, T4 - Additional switch track located in position #1 or 4

V - High temperature option (-18 to +205°C)W - Rod wiper (Buna N only) (see page14)Y - Moly-coat (MoS2 I.D. coating)


1 If magnetic position sensing is specified with Fluoroelastomer Seals, standard Buna-N based magnet will be provided. Magnetic position sensing is not reliable above 50°C.

FSMS-7040-V

TYPE

FSM - Double Acting, Single End RodFSMD - Double Acting, Double End RodFSMR - Reverse ActingFSMS - Single Acting

STROKE LENGTH

5 - 5mm40 - 40mm

100 - 100mmETC.

BORE SIZE

04 - 19mm09 - 27mm17 - 38mm31 - 50mm

OPTIONS

(Enter in alphabetical order, except EE which is last)


12

Bimba Square Flat-1 Series Metric

Basic Models

Model FSM(Double Acting, SingleEnd Rod)Standard strokes

3.2mm, 5, 10, 15, 20, 25,30, 40, 50, 80, 100m

*For C and DD dimensionswith – M option, see page 22.

Model FSMD(Double Acting,Double End Rod)Standard strokes

3.2mm, 5, 10, 15, 20,25, 30, 40, 50, 80,100mm


Model FSMS(Single Acting, SpringReturn, Rod NormallyRetracted)Standard strokes

3.2mm, 5, 10, 15, 20,25, 30, 40, 50mmContact Distributor for priceand dimensions over 50mmstroke. See page 15 forspring forces.*For C and DD dimensionswith – M option, see page 22.

DD - 4 PLACES

CACA

Bc + STROKE

F RODDIA.

3.2

GKTYP.

J

LPORT

LLC*TYP.

C*TYP.

C*TYP.

C*TYP.

E

LPORT

A SQ.

LL

H

DD* -2 PLACESEACH END

C*TYP.

DD - 4 PLACES

CACA

Ba + STROKE

F RODDIA.

3.2

GKTYP.

J

LPORT

LLC*TYP.

C*TYP.

C*TYP.

E

A SQ.

LPORT

LL

H


DD - 4 PLACES

CACABa + STROKE

F ROD DIA.

G

J

LPORT

LLC*TYP.

C*TYP.

C*TYP.

C*TYP.

3.2+STROKE

3.2K

TYP.

ETYP.

A SQ.

LPORT

LLH


LPORT

C TYP

DD -4 PLACESEACH END

CTYP.LL

CTYP.

CTYP.

Ba + STROKE

J

CA

KTYP.

G

F ROD DIA.

3.2

CADD -4 PLACES

HLL

LPORT

Aw

Ah

E

Ba + STROKE

CA

DD -4 PLACES

CA

F ROD DIA.

0.13 +STROKE

J GKTYP.

3.2

ETYP

Aw

HLL

LPORT

Ah

C TYP

CTYP.


LPORT

LL

CTYP.

CTYP.

Bore sizes63mm, 76mm,

101mm

Bore sizes19mm, 27mm,38mm, 50mm


101mm



13


Bore E Standard E Fine E Depth F G H J K L LL

19mm (04) M5 x 0.8 M5 x 0.5 11.7 7.9 10.7 6.0 10.7 3.6 M5 7.5

27mm (09) M8 x 1.25 M8 x 1.0 17.8 12.7 14.9 11.0 12.7 6.4 G 1/8 12.8

38mm (17) M10 x 1.5 M10 x 1.25 17.8 15.9 14.6 12.0 12.7 6.4 G 1/8 17.5

50mm (31) M12 x 1.75 M12 x 1.25 17.8 19.1 15.7 16.0 15.7 6.4 G 1/8 19.6

63mm (50) M12 M12 x 1.25 17.8 19.1 21.4 16.0 21.4 10.7 G 1/8 19.7

76mm (70) M16 M16 x 1.5 18.5 22.2 22.2 19.0 22.2 11.1 G 1/8 24.9

101mm (125) M20 M20 x 1.5 20.3 25.4 25.4 22.0 25.4 12.7 G 1/4 31.8

Dimensions(mm)

Bore Aw Ah Ba*Bc* Bd*

C CA DD0-25mm 26-50mm 0-25mm 26-50mm

19mm (04) N/A 31.8 19.0 25.4 39.7 31.8 46.0 10.0 7.0 M4 x 0.7

27mm (09) N/A 38.1 31.8 31.8 47.6 44.4 60.3 12.5 9.4 M4 x 0.7

38mm (17) N/A 50.8 31.8 31.8 47.6 44.4 60.3 18.0 7.9 M5 x 0.8

50mm (31) N/A 63.5 33.4 33.4 49.2 46.0 61.9 22.0 9.7 M6 x 1.0

63mm (50) 83.3 82.6 42.2 42.2 64.5 60.7 83.1 30.0 10.7 M8 x 1.25

76mm (70) 96.0 95.3 43.4 43.4 65.5 62.0 84.1 36.5 11.1 M8 x 1.25

101mm (125) 128.0 127.0 50.8 50.8 73.2 69.8 92.0 46.0 12.7 M12 x 1.75

* See page 14 for length adders for options.

Basic Models

DD - 4 PLACES

CACA

Bd + STROKE

F RODDIA.

GKTYP.

J


LPORT

LLC*TYP.

C*TYP.

C*TYP.

C*TYP.

3.2 +STROKE

A SQ.

LPORT

LL

H

E

Model FSMR(Reverse Acting, SpringReturn, Rod NormallyExtended)Standard strokes

3.2mm, 5, 10, 15, 20,25, 30, 40, 50mm

Contact Distributor for priceand dimensions over 50mmstroke. See page 15 forspring forces.



LPORT

C TYP

CTYP.

LL

CTYP.

CTYP.

J

CABd + STROKE

DD -4 PLACESCA

GKTYP.

F ROD DIA.

3.2 +STROKE

HLL

Aw

Ah

E

LPORT


101mm


Model FSMS(Continued)

LPORT


C TYP

CTYP.

LL

CTYP.

CTYP.

Bc + STROKE

J

CADD -4 PLACESCA

GKTYP.

F ROD DIA.

3.2

HLL

Aw

Ah

E

LPORT


101mm

14


Bore WD

19mm (04) 17.5

27mm (09) 22.2

38mm (17) 25.4

50mm (31) 28.6

63mm (50) 28.6

76mm (70) 31.8

101mm (125) 34.9

Options(mm)

Male Rod Ends (Option MT or MTF)Rod Wiper (Option W)(Buna N standard,

not available in fluoroelastomer)

(Dimensional variations from standard as shown)

Bore

Length Adder

Low Friction Seals (L)

Magnetic Position Sensing* (M)

Low Friction Seals and Magnetic

Position Sensing

19mm (04) 6.4 19.1 19.1

27mm (09) 9.5 12.7 12.7

38mm (17) 9.5 15.9 15.9

50mm (31) 9.5 15.9 15.9

63mm (50) 9.5 22.2 22.2

76mm (70) 12.7 22.2 22.2

101mm (125) 12.7 22.2 22.2

*A minimum stroke of 9.5mm is required to sense extending end-of-stroke position.

BoreE

LGMT MTF

19mm (04) M5 M5 x 0.5 10

27mm (09) M8 M8 x 1.0 12

38mm (17) M10 M10 x 1.25 12

50mm (31) M12 M12 x 1.25 16

63mm (50) M12 M12 x 1.25 16

76mm (70) M16 M16 x 1.5 20

101mm (125) M20 M20 x 1.5 20

15


Options(mm)FSMD Hollow Rods (Option H)

BoreHole Diameter

FemaleRod Threads

MaleRod Threads

19mm (04) 3.6 2.4

27mm (09) 5.6 4.0

38mm (17) 7.1 4.8

50mm (31) 9.5 6.4

63mm (50) 9.5 6.4

76mm (70) 11.1 7.9

101mm (125) 12.7 9.5

Enclosed Spring Forces

BoreMaximum

Load

Spring Rate

1-25mm stroke 26-50mm stroke

19mm (04) 45N 1.05 N/mm .44 N/mm

27mm (09) 50N 1.05 N/mm .44 N/mm

38mm (17) 50mm (31) 57N 0.95 N/mm .39 N/mm

63mm (50)

110 N 1.13 N/mm .48 N/mm76mm (70)

101mm (125)

16


Repair Kits

Basic Repair Kit (K-B-FSD)*


PF-1 Rod Seal 2

PF-2 Piston Seal 1

PF-41 Tube Seal 2

PF-4** Bushing 3

Wiper Option Basic Repair Kit (K-B-FS-W)*


PF-1 Rod Seal 1

PF-2 Piston Seal 1

PF-41 Tube Seal 2

PF-4 Bushing 1


PF-6 Wiper 1

*Must specify bore size when ordered. Contact your local BIMBA Distributor for pricing on kits and other repair parts.**Note: On FSMD (Double Acting, Double End Rod) models, two bushings are provided on the head end with tie rod nuts.Opposite head end has one bushing.

Basic Repair Kit (K-B-FS)*


PF-1 Rod Seal 1

PF-2 Piston Seal 1

PF-41 Tube Seal 2

PF-4 Bushing 2

Double End Rod KitsSingle End Rod Kits

Wiper Option Basic Repair Kit (K-B-FSD-W)*


PF-1 Rod Seal 2

PF-2 Piston Seal 1

PF-41 Tube Seal 2

PF-4** Bushing 1


PF-6 Wiper 2

Weights

Bore


FSM, FSMS FSMD FSMR

BaseAdder per

5mm of stroke

BaseAdder per

5mm of stroke

Adder per 5mm of

stroke for -H option

BaseAdder per

5mm of stroke

19mm (04) 62 4.4 68 9 6.8 62 4.4

27mm (09) 145 9 162 17.8 13.4 155 9

38mm (17) 286 13.4 298 26.7 22.3 290 13.4

50mm (31) 403 17.8 454 35.5 26.7 425 17.8

63mm (50) 809 11.3 968 17 14.2 883 11.3

76mm (70) 1138 17 1395 25.5 19.8 1240 17

101mm (125) 2026 17 2482 25.5 19.8 2199 17

17

Metric Bimba Flat-II Series

Flat-II nonrotating, double-acting cylinder provides the answer to applicationswhere rotation cannot be tolerated and space is at a minimum. Nonrotation isachieved with dual piston rods and a rod end block that insures the rods workin tandem. Flat-II eliminates the need for external alignment devices, such asguides, rods and alignment posts or pins.

• Body — 4301 Stainless Steel• Heads — Anodized Aluminum Alloy• Piston Rod — Ground and Polished 4305 Stainless Steel• Piston Seals — Buna N Block V (High temperature seals optional)• Rod Bushing — Oil Impregnated Bronze• Rod Seals — Buna N O-ring (High temperature seals optional)• Tie Rods — 4305 Stainless Steel• Rod End Block — Anodized Aluminum Alloy • Pressure Rating — 14 Bar Maximum (Air only)• Temperature Rating — From -25°C to +65°C

Buna N seals with a temperature range of -25°C to +65°C are standard inall Bimba air cylinders. Fluoroelastomer seals rated for higher temperatureapplications are available. If cylinders are operated below -18°C forextended time periods, special modifications may be required. Specialseal materials are available upon request.

The model number for Flat-II consists of three alphanumeric clusters. These designate type, bore size and strokelength, and mounting and special options. Please refer to the charts below for an example of Model NumberFTM-0425-3CE. This is a nonrotating, double-acting, 19mm bore, 25mm stroke cylinder with threaded mountingholes both ends and counterbored mounting holes in the rod end block.

How to Order

FTM-0425-3 CE

TYPE STROKE LENGTH

5 - 5mm40 - 40mm

100 - 100mmETC.

FTM - Nonrotating, Double Acting

MOUNTING OPTIONS OPTIONS

(Enter in numeric order) (Enter in alphabetical order, except EE which is last)


1N - Pivot mount 90° from standard2F - Front trunnion mount2R - Rear trunnion mount

3 - Threaded mounting holes, both ends3F - Threaded mounting holes, front3R - Threaded mounting holes, rear


CE - Counterbored rod end block (see page 19)G - Magnalube® G

M, M1, M3, M4 - Magnetic position sensing (see page 78)1

P3 - Front port position (see page 18)T1, T3, T4 - Additional switch mounting post

located in position #1, 3 or 4V - High temperature seals (-18 to +205°C)Y - Moly-coat (MoS2 I.D. coating)


1 If magnetic position sensing is specified with FluoroelastomerSeals, standard Buna-N based magnet will be provided. Magnetic position sensing is not reliable above 50°C.


BORE SIZE

04 - 19mm09 - 27mm17 - 38mm31 - 50mm

18

Bimba Flat-II Series Metric

X

Basic Model

B + STROKE

VL

JJ J

KK K

1.6

V

A HRODDIA.F

C BOLTCIRCLE

4 CLEARANCEHOLES FORD SOCKET HEADCAP SCREW

VH

VE THREADED2 PLACES

L PORT

1

2

3

4

Model FTM(Nonrotating, double acting)

Standard strokes3.2mm, 5, 10, 15, 20, 25, 30,40, 50, 80, 100mmLonger strokes availableupon request

Mounting OptionsTrunnion Mount(rear or front)(-2R shown)

Pivot Mount(complete with bronze bushing)(-1 shown)

Threaded Mounting Holes(available either or both ends)(-3R shown)


*43° 19mm bore only. 45° all other bores.

M

PN

P

*

90°TYP.

4 THREADEDR HOLES

C BOLTCIRCLE

19

Metric Bimba Flat-II Series

Dimensions(mm)

Counterbored Rod End Block

Bore J JJ K KK L M N P Q R

19mm (04) 8.7 11.9 3.6 6.8 M5 8 3 4.5 5 M3

27mm (09) 12.7 17.5 6.4 11.1 G 1/8 13 6 6.5 5 M3

38mm (17) 12.7 17.5 6.4 11.1 G 1/8 13 6 6.5 10 M5

50mm (31) 13.5 18.3 6.4 11.1 G 1/8 13 6 6.5 10 M5

Bore S T U V VT VL VH W X Y Z

19mm (04) 9.5 5 6.5 9.0 9.5 30.0 22.0 19 6 19 5

27mm (09) 9.5 6.5 6.5 9.0 9.5 37.0 27.0 20.5 6 19 5

38mm (17) 19 6.5 11.5 12.0 12.7 51.0 38.0 30 9 35 9.5

50mm (31) 19 8 11 15.0 15.9 64.0 48.0 32 9 35 9.5

* Magnetic Position Sensing Length Adder: 15.9mm. A minimum stroke of 9.5mm is required to sense extending end-of-stroke position.

Bore A B* C D E EC F H

19mm (04) 38.0 23.8 31.0 M3 M3 x 0.5 M3 4.8 8.4

27mm (09) 50.6 33.3 43.0 M3 M4 x 0.7 M4 6.4 10.7

38mm (17) 66.4 33.3 56.0 M5 M6 x 1.0 M6 9.5 14.3

50mm (31) 79.1 34.9 68.0 M5 M8 x 1.25 M8 12.7 19.1

VLVH

V

1.6

FORSOCKETHEAD CAPSCREWS(2 PLACES)

EC

20

Bimba Flat-II Series Metric

TL3

K

Nonrotation is achieved through the use of dual piston rods incorporated into the body of the Flat-IIcylinder. The rods are securely attached to the piston by our unique spin-riveting process. A rod endblock is used to insure the rods work in tandem—as a team. This end block also acts as a usefulsurface to easily accommodate any mounting attachments required to get the job done. For mount-ing convenience, the rod end block is provided with threaded mounting holes or optionalcounterbored holes.

As with any cylinder application, side loading should be avoided. The two smaller rods will havemore deflection due to side load than the one standard rod in a comparable Flat-1 model.

Where T = Torque (Cm.-Kg.)L = Length (see sketch below)K = Per chart aboveO = Angular deflection

O =

The Flat-II is intended to work satisfactorily against pure torsional loads.The maximum torsional load per bore size is shown in the following table:

Bore 19mm (04) 27mm (09) 38mm (17) 50mm (31)

Torque (cm-kg) 0.35 1.15 5.77 11.55

K 85.38 436.06 3914.1 22034

The amount of angular deflection, in degrees, can be approximated by the following formula:

Rotational Tolerance Deflection L Value

L

Bore Maximum Rotation19mm (04) ±1°

27mm (09) ±3/4°

38mm (17) ±1/2°

50mm (31) ±1/2°

Note: To prevent rod distortion, the rod end block must be fastened securely.

WeightsRepair Kits

*Must specify bore size when ordered.Contact your local BIMBA Distributor for pricingon kits and other repair parts.

Basic Repair Kit (K-B-FT)*


PF-29 Rod Seal 2

PF-30 Piston Seal 2

PF-3 Tube Seal 2

PF-31 Bushing 4

21

Metric Bimba Square Flat-II Series

CE - Counterbored EndblockG - Magnalube® GK - Endblock rotated 90 degrees (see page 24)L - Low Friction Seals (see page 23)

M, M1, M4 - Magnetic Position Sensing (see page 78)1

T1, T4 - Additional switch track located in position #1 or 4V - High temperature seals (-18°C to 205°C)Y - Moly-coat (MoS2 I.D. coating)


1 If magnetic position sensing is specified with Fluoroelastomer Seals, standardBuna-N based magnet will be provided. Magnetic position sensing is not reliableabove 50°C.

How to Order

FSTM-1740-V

TYPE STROKE LENGTHBORE SIZE

The Model Number for all Square Flat-II cylinders consists of three alphanumeric clusters. These designate type,bore size and stroke length and special options. Please refer to the charts below for an example of ModelNumber FSTM-1740-V. This is a nonrotating, double acting, 38mm bore, 40mm stroke cylinder, with hightemperature option.

FSTM - Nonrotating, Double Acting 04 - 19mm09 - 27mm17 - 38mm31 - 50mm

5 - 5mm40 - 40mm

100 - 100mmETC.

(Enter in alphabetical order, except EE which is last)

OPTIONS

Metric Square Flat-II nonrotating, double acting cylinder provides the answer to applications where rotationcannot be tolerated. Nonrotation is achieved with dual piston rods and a rod end block that insures the rods workin tandem. Square Flat-II eliminates the need for external alignment devices. It also provides a convenientalternative for horizontal and side mounting, with provisions for both bottom flush or face mounting. Centerlinedistances are minimized, facilitating side-by-side cylinder mounting.





• Piston Seals — Enhanced Lubricity Buna N (High temperature seals optional)

• Rod Bushing — Bronze

• Rod Seals — Buna N Block V (High temperature seals optional)

• Tie Rods — 4305 Stainless Steel

• Rod End Block — Anodized Aluminum Alloy



Buna N seals with a temperature range of -25°C to +65°C are standard in allBimba air cylinders. Fluoroelastomer seals rated for higher temperatureapplications are available. If cylinders are operated below -18°C for extendedtime periods, special modifications may be required. Special seal materialsare available upon request.

22

Bimba Square Flat-II Series Metric

C*#4 - 40 UNC - 2B x .141DPSWITCH TRACK MOUNTING

C*

C*

C*LPORT

M (TYP)

LLK

(TYP)

GJ

V

.062CA CA

B + STROKE

DD - 4 PLACES

DD* - 3 PLACES

A SQ.Ø ROD

F

THREADED2 - PLACES

E

H

Basic Model

1.6V

VH VL

EC FORSOCKET HEAD CAPSCREWS (2 - PLACES)

Bore A B C CA DD E EC F G H

19mm (04) 31.8 19 10.0 7.0 M4 x 0.7 M3 x 0.5 M3 4.8 10.7 8.4

27mm (09) 38.1 31.8 12.5 9.4 M4 x 0.7 M4 x 0.7 M4 6.4 14.9 10.7

38mm (17) 50.8 31.8 18.0 7.9 M5 x 0.8 M6 x 1.0 M6 9.5 14.6 14.3

50mm (31) 63.5 33.3 22.0 9.7 M6 x 1.0 M8 x 1.25 M8 12.7 15.7 19.1

Bore J K L LL M V VH VL

19mm (04) 10.7 4.8 M5 8.9 8.9 9.0 22.0 31.0

27mm (09) 12.7 6.4 G 1/8 10.7 8.2 9.0 27.0 37.0

38mm (17) 12.7 6.4 G 1/8 15.2 5.1 12.0 38.0 50.0

50mm (31) 15.7 6.4 G 1/8 19.3 4.7 15.0 48.0 63.0

A minimum stroke of 9.5mm is required to sense extending end-of-stroke position.See page 23 for length adders for magnet option.

Counterbored Rod End Block

Model FSTM(Nonrotating, doubleacting)

Standard strokes3.2mm, 5, 10, 15, 20, 25,30, 40, 50, 80, 100mm

Longer strokes availableupon request*Cand DD dimensions apply toSquare Flat-1 models with– M option in 19, 27,38, and 50mm bore sizes).

Dimensions (MM)

23

Metric Bimba Square Flat-II Series

Options

Repair KitsBasic Repair Kit (K-B-FSTM)*


PF-29-FSTM Rod Seal 2

PF-30-FSTM Piston Seal 1

PF-3-FSTM Tube Seal 2

BoreApproximate Cylinder Weights (grams)

Base Adder per 5mm

of stroke

19mm (04) 76 4.4

27mm (09) 181 22.3

38mm (17) 345 31.2

50mm (31) 467 40.0

Bore

Length Adder

Low Friction Seals (L)


Low Friction Seals and Magnetic

Position Sensing

19mm (04) 6.4 19 19

27mm (09) 9.7 12.7 12.7

38mm (17) 9.7 16 16

50mm (31) 9.7 16 16

Weights

Switch LocationFor the M Option, the switch mounting track will be located in Position 2.To locate the track in other positions, specify M1 or M4. To includeadditional track, specify T1 or T4.

Note: Dimension applies to all bore sizes.

Bimba Hall Effect SwitchesMagnetic position sensing is achieved by adding a magnet to an optional, modified piston. The switchmounting causes an extension outside of the cylinder diameter as shown.

3

9.3

4

1

2

Complete information on Bimba position sensing switches is available in Catalog SW. The followingswitches are available for Metric Square Flat-II cylinders:

Track-mounted Hall Effect Switches

HK HKQHC HCQ


24

Bimba Square Flat-II Series Metric

L = 1.6 + STROKE

L

Nonrotation is achieved through the use of dual piston rods incorporated into the body of the Flat-II cylinder. The rods are securely attached to the piston by our unique spin-riveting process. A rod end block isused to insure the rods work in tandem—as a team. This end block also acts as a useful surface to easilyaccommodate any mounting attachments required to get the job done. For mounting convenience, the rod endblock is provided with threaded mounting holes or optional counterbored holes.

As with any cylinder application, side loading should be avoided (see option K below). The two smaller rods willhave more deflection due to side load than the one standard rod in a comparable Flat-1 model.

Where T = Torque (Cm.-Kg.)L = Length (see sketch below)K = Per chart aboveØ = Angular deflection

The amount of angular deflection, in degrees, can be approximated by the following formula:

Rotational Tolerance Deflection L Value

Bore Maximum Rotation19mm (04) ±1°

27mm (09) ±3/4°

38mm (17) ±1/2°

50mm (31) ±1/2°

The Flat-II is intended to work satisfactorily against pure torsional loads.The maximum torsional load per bore size is shown in the following table:

Note: To prevent rod distortion, the rod end block must be fastened securely.

Ø = TL3

K

If side load cannot be avoided,the side load should be appliedperpendicular to the planeformed by the two piston rods.

Option K - Endblock Rotated 90°

25

Metric Bimba FM2, FM3, FM4 Series

Space-Saving Cylinders That Multiply Force OutputThe Bimba FM2, FM3, FM4 Series Flat-1 are double-acting, singleend rod cylinders that multiply the force output by supplying air tomultiple pistons on extension. They save space and eliminate theneed for a higher pressure system. Only one piston is powered onthe return stroke, saving air volume and operating costs.

• Body — 4301 Stainless Steel (X5 CrNi 18.9)


• Piston Rod — Ground and Polished 4305 Stainless Steel (X12 CrNi18.8)





Buna N seals with a temperature range of -25°C to +65°C arestandard in all Bimba air cylinders. Fluoroelastomer seals rated forhigher temperature applications are available. If cylinders are oper-ated below -18°C for extended time periods, special modificationsmay be required. Special seal materials are available upon request.

How it Works

AirExhaust

AirDrawn In

AirDrawn In

AirDrawn In

AirInlet

Retraction – air supplied to one piston only

Extension – air supplied to multiple pistons

AirInlet

AirExhaust

AirExhaust

AirExhaust

AirExhaust

Retraction-air supplied to one piston only

Extension-air supplied to multiple pistons

26

Bimba FM2, FM3, FM4 Series Metric

The model number for all FM2 Series Flat-1 cylinders consists of three alphanumeric clusters. These designate type,bore size and stroke length, and mounting and special options. Please refer to the charts below for our example ofModel Number FM2-5025-3M. This is a 63mm bore FM2 Series Flat-1 with 25mm stroke, threaded mounting holesin both ends, with the magnetic position sensing option.

How to Order

FM2-5025-3 M

TYPE STROKE LENGTH

5 - 5mm40 - 40mm

100 - 100mmETC.

BORE SIZE

50 - 63mm70 - 76mm125 - 101mm

FM2 - Two stage extend, single stage retractFM3 - Three stage extend, single stage retractFM4 - Four stage extend, single stage retract

MOUNTING OPTIONS OPTIONS

(Enter in numeric order) (Enter in alphabetical order, except EE which is last)

3 - Threaded mounting holes,both ends

3F - Threaded mounting holes, front3R - Threaded mounting holes, rear


Multiply the air line pressure by the power factor to get the approximateforce. For example, an FM2-5025-3 operated at 6 bars will exert a forceof 3636 N. on extension, and 1704 N. on retraction.

FTF - Fine female thread (see page 29)G - Magnalube® GL - Low friction seals (see page 27)


MTF - Male rod end (fine thread) (see page 27)MT - Male rod end (coarse thread) (see page 27)NT - Non-threaded rod

P2, P3, P4 - Front port position #2, etc. (see page 28)P6, P7, P8 - Rear port position #6, etc. (see page 28)T1, T3, T4 - Additional switch mounting post located

in position #1, 3 or 4V - High temperature seals (-18° to +205° C)

W - Rod wiper (Buna N only) (see page 27)Y - Moly-coat (MoS2 I.D. coating)


1 If magnetic position sensing is specified with Fluoroelastomer Seals, standard Buna-N based magnet will be provided. Magneticposition sensing is not reliable above 50°C.


27


(Dimensional variations from standard as shown)

Options(mm)


Rod Wiper (Option W)(Buna N standard, not available in Viton)

Male Rod Ends (Option MT or MTF)

Bore WD

63mm (50) 28.6

76mm (70) 31.8

101mm (125) 34.9

Bore MT MTF LG

63mm (50) M12 M12 x 1.25 16

76mm (70) M16 M16 x 1.5 20

101mm (125) M20 M20 x 1.5 20

ETHREAD

LG4.8

9.5

WD

Bore Type

Length Adder

Low Friction Seal (L)


Low Friction Seal & Magnetic Position

Sensing (LM)

63mm (50)

FM2 19.0

22.2

31.8

FM3 28.7 41.4

FM4 38.1 50.8

76mm (70)

FM2 25.4

22.2

35.1

FM3 38.1 47.8

FM4 50.8 60.5

101mm (125)

FM2 25.4

22.2

35.1

FM3 38.1 47.8

FM4 50.8 60.5

28


B + (3 x STROKE)*

PORT

VENTST

J (TYP)

3.2

PORTL PORT

FROD DIA.

C BOLTCIRCLE

2

1 3

4

E(4) CLEARHOLES FOR DSOCKET HEADCAP SCREW

H

A

KV

6

7 5

8

Z DIA. ADDITIONAL MOUNTINGHOLES FOR FM3 & FM4 76mm &101mm BORES ONLY

B + (4 x STROKE)*

PORT

VENTST

J (TYP)

3.2

PORTL PORT

FROD DIA.

C BOLTCIRCLE

2

1 3

4


H

A

KV

6

7 5

8

Z DIA. ADDITIONAL MOUNTINGHOLES FOR FM3 & FM4 76mm &101mm BORES ONLY

B + (2 x STROKE)*

PORT

VENTT

J (TYP)

3.2

PORTL PORT

FROD DIA.

C BOLTCIRCLE

2

1 3

4


H

A

KV

6

7 5

8

Basic Model Standard strokes3.2mm, 5mm, 10mm, 15mm, 20mm, 25mm, 30mm, 40mm, 50mm, 80mm, 100mmSpecial strokes available on request

Model FM2

Model FM3

Model FM4

29


Mounting OptionsThreaded Mounting Holes(available either or both ends)(-3R shown)

Dimensions(mm)

Bore AB**

C D E Std. E Fine E DepthFM2 FM3 FM4

63mm (50) 95.0 58.2 80.0 102.1 83.0 M6 M12 M12 x 1.25 17.8

76mm (70) 107.7 60.7 83.3 106.2 96.0 M6 M16 M16 x 1.5 18.5

101mm (125) 139.5 77.2 105.4 133.9 125 M8 M20 M20 x 1.5 20.3

Bore F H J K L R T V X Z

63mm (50) 19.1 16.0 16.7 8.3 R 1/8 M6 23.0 14.7 10.5 N/A

76mm (70) 22.2 19.0 17.5 8.3 R 1/8 M6 23.8 14.7 10.5 7.1

101mm (125) 25.4 22.0 21.4 10.7 R 1/4 M8 31.0 19.1 13.5 8.6


X

Bore Type

"B"

Stroke

3.175 6.350

63mm (50)

FM2 67.3 70.4

FM3 92.5 98.3

FM4 117.6 126.2

76mm (70)

FM2 69.9 73.2

FM3 95.8 101.9

FM4 121.7 130.8

101mm (125)

FM2 85.9 89.7

FM3 117.1 124.2

FM4 148.6 158.5

**For Strokes 3.2 and .5


30


Repair Kits

Weights

Basic Repair Kit (K-B-FM__)*

Part No. Description Quantity**

PF-1 Rod Seal 2, 3 or 4

PF-2 Piston Seal 2, 3 or 4

PF-3 Tube Seal 3, 4 or 5

PF-4 Bushing 3, 4 or 5

Wiper Option Repair Kit (K-B-FM__-W)*

Part No. Description Quantity**

PF-1 Rod Seal 2, 3 or 4

PF-2 Piston Seal 2, 3 or 4

PF-3 Tube Seal 3, 4 or 5

PF-4 Bushing 3, 4 or 5


PF-6 Wiper 1

Bore


Base Adder per 5mm of stroke

FM2 FM3 FM4 FM2 FM3 FM4

63mm (50) 1055 1511 1967 53.5 80.2 71.4

76mm (70) 1415 2013 2611 71.4 107.0 142.7

101mm (125) 2640 3793 4947 89.1 133.7 178.3

*Must specify model and bore size when ordered.**Quantities listed correspond with FM2, FM3 or FM4.

31

Metric Bimba FMP Series

The Bimba Metric Multiple Position FMP Flat-1 is a double-acting, single rod end cylinder that provides three positions withjust one cylinder.*

• Body — 4301 Stainless Steel (X5 CrNi 18.9)

• Heads—Anodized Aluminum Alloy

• Piston Rod — Ground and Polished 4305 Stainless Steel(X12 CrNi S18.8)





Buna N seals with a temperature range of -25°C to +65°Care standard in all Bimba air cylinders. Fluoroelastomerseals rated for higher temperature applications are available.If cylinders are operated at temperatures below -18°C forextended time periods, special modifications may berequired. Special seal materials are available on request.

*Other positions (4, 5, etc.) are available as specials. Contact your localBimba distributor for more information.

POSITION 1STROKE A EXTENDED

AIR INPORT 1

STROKE A

POSITION 3 FULLYRETRACTED

AIR INPORT 3

POSITION 2STROKE B EXTENDED

AIR INPORT 2

STROKE B

How it Works

Position 1Air is supplied toPort 1, cylinderextends strokelength A.

Position 3Cylinder is fullyretracted bysupplying air toPort 3.

Position 2Air is supplied toPort 2, cylinderextends strokelength B.

Note: For Magnetic Position Sensing option, magnet is mounted only on the piston of the Stroke B side.

32

Bimba FMP Series Metric

The model number for all Metric Multiple Position FMP Flat-1 cylinders consists of three alphanumeric clusters.The first cluster designates type, the second cluster bore size and stroke lengths A and B, and the third clusterdesignates mounting and special options. Please refer to the charts below for an example of Model NumberFMP-1750/25-1V. This is a 38mm bore multiple position FMP Flat-1 with a 50mm stroke for position A, plus anadditional stroke of 25mm for position B, with a pivot mount on the rear head and high temperature option.

How to Order

FMP-1750/25-1V

MOUNTING OPTIONS

TYPE BORE SIZE

02 - 14mm 31 - 50mm04 - 19mm 50 - 63mm09 - 27mm 70 - 76mm17 - 38mm 125 - 101mm

25 - 25mm50 - 50mm75 - 75mm

ETC.

STROKE LENGTH

FMP -Double acting multiple position,

single end rod

STROKE LENGTH

25 - 25mm50 - 50mm75 - 75mm

ETC.

OPTIONS

(Enter in alphabetical order, except EE which is last)(Enter in numeric order)


1N - Pivot mount 90° from standard3 - Threaded mounting holes, both ends

3F - Threaded mounting holes, front3R - Threaded mounting holes, rear


FTF - Fine female rod thread (see page 35)G - Magnalube® GL - Low friction seals (see table page 33)


MT - Male rod thread end (coarse thread) (see page 33)MTF - Male rod thread end (fine thread) (see page 33)

NT - Non-threaded rodP2*, P3, P4* - Front port position #2, etc. (see page 34)P6*, P7, P8* - Rear port position #6, etc. (see page 34)

T1, T3, T4 - Additional switch mounting postlocated in position #1, 3 or 4

V - High temperature seals (-18 to +205°C)W - Rod wiper (Buna-N only) (see page 33)Y - Moly-coat (MoS2 I.D. coating)


*Not available in 14mm bore1If magnetic position sensing is specified with Fluoroelastomer Seals, standard Buna-N based magnet will be provided. Magnetic position sensing is not reliable above 50°C.


33


Options(mm)(Dimensional variations from standard as shown.)


Length Adder

BoreLow Friction

Seals (L)Magnetic Position

Sensing* (M)Low Friction Seals and Magnetic

Position Sensing

14mm (02), 19mm (04) 12.7 22.2 28.6

27mm (09), 38mm (17), 50mm (31), 63mm (50) 19.1 22.2 31.8

76mm (70), 101mm (125) 25.4 22.2 34.9

ETHREAD

LG

BoreE

LGMT MTF

14mm (02) M4 M4 x 0.5 10

19mm (04) M5 M5 x 0.5 10

27mm (09) M8 M8 x 1.0 12

38mm (17) M10 M10 x 1.25 12

50mm (31) 63mm (50) M12 M12 x 1.25 16

76mm (70) M16 M16 x 1.5 20

101mm (125) M20 M20 x 1.5 20

Male Rod Ends (Option MT or MTF)

4.8

9.5

WD

Rod Wiper (Option W)(Buna N standard, not available in Viton)

Bore WD

14mm (02) 14.3

19mm (04) 17.5

27mm (09) 22.2

38mm (17) 25.4

50mm (31) 63mm (50) 28.6

76mm (70) 31.8

101mm (125) 34.9

14mm 19mm 27mm 38mm 50mm 63mm 76mm 101mm

BASE MODEL STROKE A 4.8 4.8 6.4 6.4 6.4 9.5 9.5 8.7

Minimum Stroke

No minimum for stroke B. No minimum for stroke A or B with low friction seal option.

BoreModel

34


Basic Model

Threaded Mounting Holes(available either or both ends)(-3R shown)14mm Bore

Pivot Mount(-1 shown) Complete with bronzepivot bushing. (Not available as anaccessory)

Screw Clearance Holes(available either or both ends)(-4R shown) Screw clearance holesstandard on all center sections

Mounting Options

19mm Bore and larger

X

THREADED2R HOLES

BOLT CIRCLECLOCATION OF MTG. HOLES14mm BORE ONLY

TYP.90º

*43° - 19mm BORE ONLY 90°TYP

4 THREADEDR HOLES

C BOLTCIRCLE

*

45° - ALL OTHER BORES

35


Dimensions(mm)

BoreE

DEPTHF G H J JJ K L

14mm (02) 11.7 6.3 8.7 5.5 11.9 6.8 3.6 M5

19mm (04) 11.7 7.9 8.7 6.0 11.9 6.8 3.6 M5

27mm (09) 17.8 12.7 12.7 11.0 17.5 11.1 6.4 G 1/8

38mm (17) 17.8 15.9 12.7 12.0 17.5 11.1 6.4 G 1/8

50mm (31) 17.8 19.1 13.5 16.0 18.3 11.1 6.4 G 1/8

63mm (50) 17.8 19.1 16.7 16.0 23.0 14.7 8.3 G 1/8

76mm (70) 18.5 22.2 17.5 19.0 23.8 14.7 8.3 G 1/8

101mm (125) 20.3 25.4 21.4 22.0 31.0 20.2 10.7 G 1/4

Bore Q R S T U W X Y Z

14mm (02) 5 M3 9.5 5 6.5 19 6 16 5

19mm (04) 5 M3 9.5 5 6.5 19 6 19 5

27mm (09) 5 M3 9.5 6.5 6.5 20.5 6 19 5

38mm (17) 10 M5 19 6.5 11.5 30 9 35 9.5

50mm (31) 10 M5 19 8 11 32 9 35 9.5

63mm (50) 10 M6 19 9.5 11 33.5 10.5 35 9.5

76mm (70) 16 M6 25.5 9.5 14 43 10.5 47.5 9.5

101mm (125) 16 M8 25.5 11 14.5 44.5 13.5 47.5 9.5


Bore Aa Ba* C DD DE E

(Std) (Fine)

14mm (02) 28.5 29.0 22.5 2 M3 M4 M4 x 0.5

19mm (04) 38.0 29.0 31.0 4 M3 M5 M5 x 0.5

27mm (09) 50.6 42.5 43.0 4 M3 M8 M8 x 1.0

38mm (17) 66.4 43.3 56.0 4 M5 M10 M10 x 1.25

50mm (31) 79.1 45.6 68.0 4 M5 M12 M12 x 1.25

63mm (50) 95.0 57.2 83.0 4 M6 M12 M12 x 1.25

76mm (70) 107.7 59.5 96.0 4 M6 M16 M16 x 1.5

101mm (125) 139.5 76.2 125.0 4 M8 M20 M20 x 1.5

36


Repair Kits

Basic Repair Kit (K-B FOP)*


PF-1 Rod Seal 2

PF-2 Piston Seal 2

PF-3 Tube Seal 3

PF-4 Bushing 3

Wiper Option Repair Kit (K-B-FOP-W)*


PF-1 Rod Seal 2

PF-2 Piston Seal 2

PF-3 Tube Seal 3

PF-4 Bushing 2


PF-6 Wiper 1

Weights

Bore


BaseAdder per

5mm of stroke

14mm (02) 94 7.1

19mm (04) 128 9

27mm (09) 281 26.7

38mm (17) 530 35.5

50mm (31) 695 44.6

63mm (50) 1170 53.4

76mm (70) 1500 71.4

101mm (125) 2912 89.1

*Must specify bore size when ordered. Contact your localBimba distributor for pricing on kits and other repair parts.

37


Accessories(mm)(All Models)

Model Bore LD MT Q S SH SD TH TL

BCM-114mm (02) 19mm (04) 27mm (09)

14.5 19 5 10 3 25.5 4 20

BCM-238mm (17) 50mm (31) 63mm (50)

24 35 10 19.5 4 44.5 5.5 34

BCM-3 76mm (70) 101mm (125) 32 50 16 26 6 63.5 6.5 46

Clevis BracketAnodized aluminum alloy, complete with chrome plated steel pin

Bracket intended to mount with either rod pivot or pivot mount, not directly to thecylinder rear head.

Trunnion Bracket (pair)Anodized aluminum alloy, complete with bronze pivot bushings

Model Bore BA BT HT LT M N NA NB

BTM-1 19mm (04) 14.5 4 15.5 28.5 8 3 8 5.5

BTM-227mm (09) 38mm (17) 50mm (31)

20.5 6 22 38 12.5 6 10 8

BTM-3 63mm (50) 76mm (70) 24 8 25 41.5 16 8 12 9.5

BTM-4 101mm (125) 27 10 31.5 47.5 19 10 14 11

Model Bore E LN MS NT Q S

RPM-1/2 14mm (02) M4 9.5 11.5 6.5 5 9.5

RPM-1 19mm (04) M5 9.5 11.5 6.5 5 9.5

RPM-2 27mm (09) M8 16 11.5 6.5 5 9.5

RPM-3 38mm (17) M10 16 18.5 11 10 19

RPM-4 50mm (31) 63mm (50) M12 19 18.5 11 10 19

RPM-5 76mm (70) M16 22.5 25.5 16 16 25.5

RPM-6 101mm (125) M20 22.5 25.5 16 16 25.5

Rod PivotZinc plated, high strength, heat treated alloy steel,complete with a bronze pivot bushing and nut

TLQ PIN DIA.

SDSQUARE

MTSQUARE

S

SHBOLTHOLE DIA.

THLD

Selection Guide

Accessory Flat-1Square Flat-1

Square Flat-II

Flat-II FM2 Series

FMP

Clevis Bracket X X X X N/A X

Trunnion Bracket X N/A N/A X N/A N/A

Rod Pivot X X N/A N/A X X

ETHREAD

NT

S

Q DIA. FORPIVOT PIN

MS

LN

S

78

Bimba Pneu-Turn Rotary Actuators Metric

Thin Disc(mounted on side through center)

R

A1

A1

Thin Rectangular Plate(centered & mounted on side)

Pneu-Turn Application Checklist

Fig. 1 Fig. 2

Fig. 3 Fig. 4

Fig. 5 Fig. 6

Fig. 7

Request Pneu-Turn model number recommended byEngineering? Yes No

If no, Pneu-Turn model number to be used in your application:Air Bar Hydraulic Bar

Torque Required:0 – 15 Nm 75 – 100 Nm

15 – 35 Nm 200 – 500 Nm35 – 75 Nm other:

Application closest to (circle one):Fig. 1 Fig. 2 Fig. 3 Fig. 4 Fig. 5 Fig. 6 Fig. 7

Dimensions applicable to your lever arm:Radius mm A1 mm

A2 mm B mm

Weight and material of lever arm and attachments:N N material:

Load to be moved by the lever arm:N N

Distance from the center of the load to the center ofthe shaft: mm

Shaft Mounted: (shaft, cylinders)

This checklist makes sizing and selecting Bimba actuators easier.Bimba's Engineering Department will assist you by providing adetailed analysis of your application and, based on theinformation in the application checklist, will help you choose theactuators best suited to your needs.

Step 1. Photocopy the sketch and checklist sheets.

Step 2. Complete the sketch and checklist.

Step 3. Mail or fax the sketch and checklist to your local stocking distributor.

Date:

Your Name:

Company:

Address:

Phone:

Fax:

Axial loading? Yes NoIf yes, direction with reference to pushing or pulling thestandard shaft:

Rotation of lever arm: degrees

Time needed to move load in one direction:secs. Opposite direction secs.

May cushions be used to slow the load at the endof stroke?Yes No

May external stops be used if deemed necessary?Yes No

(horiz., vert.) (horiz., horiz.) (vert. (up), horiz.) (vert. (down) horiz.)

79

Metric Bimba Ultran Rodless Cylinder

Description of Application

1. How will the cylinder be mounted?

■■ Horizontally ■■ Vertically

If horizontal, is load above or below the cylinder?

■■ Above ■■ Below

2. What is the required stroke length?

(mm)

3. What is the weight of the load being moved?

(kg.)

4. How fast will the cylinder be cycling?

(cycles/second)

5. How far is the center of the load from the center ofthe cylinder?

a. Ultran (mm)

b. Ultran Slide (mm)

(See page_____ moment arm)

6. What is the cylinder’s velocity at the end-of-stroke?

(m/second)

7. Do you need position sensing?

■■ Yes ■■ No

If yes:

■■ end of stroke (or) ■■ mid-stroke

8. Will the cylinder be used under harsh environmentalconditions?

If yes, please explain

Additional Notes:

Ultran Application Checklist

Date:

Your Name:

Company:

Address:

Phone:

Fax:

This checklist makes sizing and selecting Bimba actuatorseasier. Bimba's Engineering Department will assist you byproviding a detailed analysis of your application and, basedon the information in the application checklist, will help youchoose the actuators best suited to your needs.

Step 1. Photocopy the sketch and checklist sheets.

Step 2. Complete the sketch and checklist.

Step 3. Mail or fax the sketch and checklist to your local stocking distributor.

80

Bimba Switches Metric

Switch Application Selection Guide

Switch Selection ChartSwitch Type Pneu-

TurnUltran Flat-1

ReedSwitch

SolidState

Switch

MiniatureGMR

Switch

InductiveProximity

MRS-.087

MRS-.087-B

MRS-.087-BL

MRS-.087-PBL

MRS-1.5-B

RSU-1,RSUM-1

HSK

HSC

HK

HC

MSC

MSK

MR

PCMQ,PKMQ

R

1R1

2

2

2

X

XX

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X4

4

4

* Use resistor-capacitor protection** Minimum current= 100mA

1 Include Q and QC options where applicable for Quick Connect models

HC QCXFor Ultran Slide and Flat Series

Track Mount Solid State SwitchesHow to Order

24” (1.2m) pigtail leadHC-Current Sourcing (PNP)HK-Current Sinking (NPN)

X = Include if 144” (3.66m) pigtaillead needed (Not applicablewith Quick Connect)

SWITCH TYPE OPTIONAL Q = Quick Connect withoutcable

QC = 2 meter mating cableaccompanies switch

QCX = 5 meter mating cableaccompanies switch

OPTIONAL

HSK QCX - 04

24” (0.6m) pigtail leadHSC-Current Sourcing (PNP)HSK-Current Sinking (NPN)


Q = Quick Connectwithout cable



SWITCH TYPE OPTIONAL OPTIONAL

(See page 81)

BAND SIZE

Band Style Solid State Switches Used for Pneu-Turn*

To Order CableConnectors Separatly

81

Metric Bimba Switches

Specifying Band SizeMany of the Bimba Solid State switches are band-mounted to the actuator. For all band-styleswitches, a pre-sized band is ordered by adding a bore size designation as the last two or threedigits of the basic switch model number. For example, the current sourcing Solid State Switchmodel for a 1-1/16” bore MRS cylinder would be HSC-09.

Pneu-Turn Rotary Actuators:

Electrical SpecificationsHSK, HSC, HK, HC, Solid State Switches

(3 wire switches)Input Voltage:Load Current:

Sensor Element:Off-State Leakage:

Reverse Battery:Transient Protection:

Overvoltage Protection:Sensor Operation Indicator:

Turn-on Time:Turn-off Time:

“On” Voltage Drop:

Operational Temperature Range:

Insulation Resistance:

Flammability Rating:Packaging:

Vibration:Welding Field Immunity:

CE Mark:Cable:

Repeatability:

4.5 to 30 VDC150 mA, maximumSolid-State10 microamperes, maximum40 VDC, minimum500 Watts of peak power, minimum37 VDC maximum with up to 12 amperesRed LED for Sinking, Yellow LED for Sourcing1 microsecond1 microsecond0.4 VDC, maximum, for a Sinking Circuit1.5 VDC, maximum, for a Sourcing Circuit-20˚ F to +185˚ F25˚ C to 85˚ C100 megohms, lead to case with a 500 volt AC and or DC source

UL 94 VOIEC 529-1989, Category IP 67 TestsMil-Std-810E, Method 514.1, Category 10Immune to welding fields to 4000 amperes minimum, at a minimum

CE Compliance per engineering evaluation to certified circuits3 conductor, 24 to 26 AWG, Gray polyurethane outer jacket+/- .005"

Electrical Circuit Diagrams

POSITIVE

OUTPUT LOAD

GROUND/NEGATIVE

14

3

+

–LOAD

GROUND/NEGATIVE

14

3

OUTPUT

POSITIVE+

–

Positive+

(Vcc)

RED WHITE

SOURCINGSWITCH

BLACK Common

(Gnd)

(Gnd)

LOAD ORPLC INPUT

HSC, HC, MSC, (PNP)

Positive+

(Vcc)

RED WHITE

SINKINGSWITCH

BLACK Common

(Gnd)

Positive+

(Vcc)

LOAD ORPLC INPUT

HSK, HK, MSK (NPN)

HSCQ, HCQ, MSC

1. POSITIVE3. GROUND4. OUTPUT

431

HSKQ, HKQ, MSK

BROWN - POSITIVE

BLUE - GROUND

BLACK - OUTPUT

8mm Female Connector Face View of Male Connector

Pin and Wire Assignments for Quick Connect

Typical Solid State Sourcing Configuration Typical Solid State Sinking Configuration

Basic Circuit Layout for Programmable Logic Controllers (PLC)and Normally Off Relays and Solenoids

CAUTION: Shorting white wire to ground will damage switch

8mm Male ConnectorSourcing Solid State Switch

8mm Male ConnectorSinking Solid State Switch

Basic Circuit Layout for Programmable Logic Controllers (PLC)and Normally Off Relays and Solenoids

CAUTION: Shorting white wire to supply voltage will damage switch

distance of 0.25"

82


HC, HK Solid State Switches

Dimensions

24" (0.6m) JACKETED LEADS

.20(5.1)

.10(2.5)

.45(11.4)

1.10(27.9)

L.E.D.

CENTERLINEHALL EFFECTSENSOR

HSC, HSK 0.45(11.4)

1.10(27.9)

5(127)

1.33(33.8)

LED

0.28(7.1)

0.17(4.3)

0.20(5.1)

HSCQ, HSKQ

HSC, HSK Solid State Switches(inches shown, mm in parentheses)

24" (0.6M) JACKETED LEADS

CENTERLINESENSOR

0.53(13.5)

0.38(9.6)

0.58(14.7)

0.12(3.0)

L.E.D. L.E.D.

1.33(33.8)

0.28(7.1)

0.58(14.7)

5(127)0.53

(13.5)

0.17(4.3)

0.38(9.6) HCQ, HKQHC, HK

How to Order/List PricesFor Ultran Rodless Cylinders and Pneu-Turn Rotary Actuators

MRS - .087 -P B L QCX - 04

(See page 81)

BAND SIZE

BAND MOUNT

L = LEDOmit = No LED

LED

24” (0.6m) pigtail lead


SWITCH TYPE

OPTIONALQ = Include if Quick Connect

style needed



OPTIONAL

MRS-.087MRS-.087-B(2 wire switch)

Contacts ...................................................SPST Form A (Normally Open)

Contact Rating .....................................................................10 Watts max.

Switch Voltage........................................................200 Volts max. AC/DC

Maximum Current 500 mA max. (Resistive)

Initial Contact Resistance 0.10 ohms max.

Actuating Time Average.....................................................1.0 millisecond

MRS-.087-BLMRS-.087-BLQ(3 wire switch)


Contact Rating........................................................................9 Watts max.

Switch Voltage..........................................................................6 to 24 Volts

Maximum Current 500 mA max. (Resistive)


Actuating Time Average.....................................................1.0 millisecondLED Indicator

MRS-.087-BQ(2 wire switch)



Switch Voltage.............................................................120 Volts AC or DC

Maximum Current:........................................................500 mA (Resistive)


MRS-.087-PBLMRS-.087-PBLQ

(2 wire switch)


Contact Rating ....................................................................2.5 Watts max.

Switch Voltage.....................................................3 to 120 Volts AC or DC

Minimum Current..............................................................10mA AC or DC

Maximum Current............................................................20 mA AC or DC


Actuating Time Average.....................................................1.0 millisecondLED Indicatord

Electrical SpecificationsMRS-1.5 (1-1/16” to 2-1/2”)

MRS-1.5-S (9/16” to 3/4” bore)MRS-.1.5-B

(2 wire switch)


Voltage Rating.....................................................12 to 230 Volts (AC only)

Minimum Current..........................................................................0.1 amps

Maximum Current ................................................1.5 amps @ 50ºF(10ºC)0.5 amps @ 200ºF(93ºC)

Actuating Time Average...................................................2.0 milliseconds

RSU-1RSUM-1

(2 wire switch)



Switching Voltage..................................................200 Volts Max. AC/DC

Breakdown Voltage..............................................................250 Volts min.

Switching Current..................................................................500 mA max.

Initial Contact Resistance...................................................0.2 ohms max.


Magnetic Reed Switches

Magnetic Reed Switches

83


MRS-.087MRS-.087-B

RSUM-1

RED

BLACK

LOAD

MRS-.087-BQMRS-.087-PBLQ

8mm Male Connector

MRS-.087-BL MRS-.087-BLQ

8mm Male Connector

MRS-.087-PBL

MRS-1.5MRS-1.5-SMRS-1.5-B

Face View of Male Connector8mm Female Connector

Pin and Wire Assignments for Quick Connect

Electrical Circuit Diagrams

RED

BLACKLOAD

WHITE

+

–

RED

BLACK

LOAD

BROWN - POSITIVE

BLUE - GROUND

BLACK - OUTPUT

1. POSITIVE3. GROUND4. OUTPUT

431

RED

BLACK

LOAD

POSITIVE/HOT

OUTPUTLOAD

NEGATIVE/NEUTRAL

14

3

POSITIVE/HOTLOAD

NEGATIVE/NEUTRAL

14

3

24" (0.6m) JACKETED LEADS144" (3.66m) OPTIONAL

.12 MAX.(3.0)

1.31(33.3)

L.E.D.*

.59(15.0)

.62(15.8)

*NOTE: Only "BL" models include L.E.D.

Dimensions

MRS-.087-BQMRS-.087-BLQ

MRS-.087-PBLQ

MRS-.087

MRS-1.5

RSUM-1

1.06

.80

1.50

24" JACKETED LEADS

1.25(31.8)

.5(13.0)

1.50(38.1)

12" (.3m) LEADS

5/16" - 24 THD.(m8 x 1.25 THD.)

2X .19(4.8)

5(127)

1.31(33.3)

0.59(15.0)

1.33(33.8)

0.28(7.1)

0.17(4.3) 0.62

(15.8)

1.50 1.02

.76

24" JACKETED LEADS

(inches shown, mm in parentheses)

To order longer leads, specify D-7001-A-lead length in inches.Consult BIMBA distributor or factory for prices.

To order longer leads, specify D-7000-A-lead length in inches.Consult BIMBA distributor or factory for prices.

MRS-.087-B, MRS-.087-BLMRS-.087-PBL, MRS-1.5-B

84


Switch TypeMR- Magnetic Reed Switch

MSC- GMR Source (PNP)output

MSK- GMR Sink (NPN) outputMS- GMR auto-configure

OptionalX- Include if 144"

(3.6m) pigtail leadneeded (notapplicable withQuick Connect)

OptionalQ- 8mm Quick Connect without cable

QC- 2 meter mating cable accompaniesswitch

QCX- 5 meter mating cable accompaniesswitch

Miniature 4mm Round Reed and Solid State Switches for UltranRodless Cylinders and Pneu Turn Rotary Actuators

How to Order

Electrical Specifications

85


MS, MSX, MSQ

Note: On Quick Connect reed switch models, connect only the Blue and Brown wires on the mating cable and cut back the Black wire. Do Not connect switch to a mating cable that has been previously wired for a 3 wire solid state switch, as it will short the MRQ switch.

MS, MSX, MSQ

Color CodesBrown (+) PositiveBlack OutputBlue (-) Negative

MR, MRX, MRQ, MS, MSX, MSQ, MSC, MSCX, MSCQ, MSK, MSKX, MSKQ mm (in.)

Dimensions(mm)

Electrical Circuit DiagramMR, MRX, MRQ (Reed Switch)

MS, MSX, MSQ

MSK, MSKX, MSKQ(Sinking, Solid State)

MSC, MSCX, MSCQ(Sourcing, Solid State)

MS, MSX, MSQ(Sourcing Circuit)

LOAD

BLUE

BLACK

BROWN

CO

NFI

GU

REA

UTO

-

CIR

CU

IT

(Sinking Cicuit)

86


.51(13.0)

2.56(65.0)

M8 X 1THREADED/SNAP-ON

CONNECTOR

5/16-24 UNF

2X .16(4.0)

2X

(M8 X 1)

How to Order

Inductive Proximity SensorIntroducing Bimba Inductive Proximity Sensors for use on Ultran products. Use it on the Ultran productline for end of stroke detection where inductive solid state sensing is preferred. Refer to the UltranProduct section of the AP catalog for mounting details. The sensor can also be used on other applications where inductive proximity sensing is required.

Add C to the end of the part number to include a 2M mating cable and add CX to the end of the part number toinclude a 5M cable. For Example: PCQC includes a 2M mating cable with Proximity Sensor.

Specifications

DimensionsTo Order Mating Cables Separately

87

Notes

Bimba Manufacturing Warranty

WARRANTY

All Bimba products are warranted against defectsin workmanship or material under normal condi-tions and usage for a period of two years from thedate of shipment. Your exclusive remedy in theevent of such a defect is to return the product toour factory for repair, replacement or refund, ac-companied by our Returned Goods Form. ThisWarranty does not cover products which havebeen subject to misuse, negligence, accidents,misapplications or tampering in a way so as toaffect their normal performance. Bimba shall notbe liable for special, indirect or consequentialdamages.

Product enhancements resulting from our continuing quality improvement effort may necessitate changes in specifications without notice.All prices are F.O.B. Monee, Illinois, and are subject to change without notice.

BIMBA GIVES NO WARRANTY, EXPRESS ORIMPLIED, AS TO MERCHANTABILITY, FITNESSFOR PARTICULAR PURPOSE AS SOLD, DESCRIPTION, QUALITY OR ANY OTHERMATTER BEYOND THAT SPECIFIED ABOVE.BIMBA DOES NOT ASSUME, NOR AUTHORIZEANYONE ELSE TO ASSUME FOR IT, ANYOTHER OBLIGATION OR LIABILITY IN CON-NECTION WITH THE SALE OR USE OF ITSPRODUCTS.

Compact Metric Cylinders

Documents

Transcript of Compact Metric Cylinders