ComNet FDXT1E1M1A Instruction Manual
6
INS_FDXT1E1_REV– 11/07/12 PAGE 1 INSTALLATION AND OPERATION MANUAL FDXT1/E1(M,S)1(A,B) T1/E1 POINT-TO-POINT TRANSCEIVER FDXT1/E1(M,S)1(A,B)/R3 T1 POINT-TO-POINT TRANSCEIVER The ComNet™ FDXT1/E 1 data tr ansceivers are T1/E1 li nks that support AMI and B8ZS data signal s over one single mode or multimode optical fiber. The transceivers synchronize and regenerate data to eliminate jitter accumulated through the link. Models within this series are available for use with multimode or single mode optical f iber . Plug-and-play design ensures ease of installation requiring no electrical or optical adjustments. Each tr ansceiver incorporates a bi-color (Red/Green ) indicating LED for monitoring proper system operation. See Figure 6 on Page 5 for an explanation of LED indications. The FDXT1/E1 standard size units may be either wall or rack-mounted in a ComNet card cage, or may be installed in an IFS R3 rack with the selection of the corresponding model. See Figure A on Page 5 for mounting instructions. See Figures 1 – 6 for complete installation details. Please note that the FDXT1/E1/R3 IFS-compatible units support T1 links only.
-
Upload
jmac-supply -
Category
Documents
-
view
223 -
download
0
description
Buy the ComNet FDXT1E1M1A at JMAC Supply!https://www.jmac.com/ComNet_FDXT1_E1M1A_p/comnet-fdxt1e1m1a.htm?=scribd
Transcript of ComNet FDXT1E1M1A Instruction Manual
-
INS_FDXT1E1_REV11/07/12
PAGE 1
INSTALLATION AND OPERATION MANUAL
FDXT1/E1(M,S)1(A,B)T1/E1 PoINT-To-PoINT TRANScEIVER
FDXT1/E1(M,S)1(A,B)/R3T1 PoINT-To-PoINT TRANScEIVER
The comNet FDXT1/E1 data transceivers are T1/E1 links that support AMI and B8ZS data signals over one single mode or multimode optical fiber. The transceivers synchronize and regenerate data to eliminate jitter accumulated through the link. Models within this series are available for use with multimode or single mode optical fiber. Plug-and-play design ensures ease of installation requiring no electrical or optical adjustments.
Each transceiver incorporates a bi-color (Red/Green) indicating LED for monitoring proper system operation. See Figure 6 on Page 5 for an explanation of LED indications.
The FDXT1/E1 standard size units may be either wall or rack-mounted in a comNet card cage, or may be installed in an IFS R3 rack with the selection of the corresponding model. See Figure A on Page 5 for mounting instructions.
See Figures 1 6 for complete installation details.
Please note that the FDXT1/E1/R3 IFS-compatible units support T1 links only.
-
INS_FDXT1E1_REV11/07/12
PAGE 2
LED Indicators See Figure 8
FIGURE 1 FDXT1/E1 ComFit Units
INSTALLATION AND OPERATION MANUAL FDXT1/E1(M,S)1(A,B)
TEch SUPPORT: 1.888.678.9427
Multimode Or Single Mode Optical Fiber (Depending On Model)
E1 Connections
T1 Connections
BLACKBLACK WITH WHITE STRIPE
Power Supply:Surface Mount: 24 VAC @ 1.2W Rack Mount: From ComNet Rack
REAR PANELFRONT PANEL
SIDE VIEW
Data Format and Test Switches See Figure 7
GND
+Vin PWR
OPT
ICAL
FDXT1E1
S MA BT1/E1 CCITT
TRANSCEIVER
LINK
TX
RX
TEST
ON
1234
E1IN
E1OUT
T1
GND
+Vin PWR
OPT
ICAL
FDXT1E1
S MA BT1/E1 CCITT
TRANSCEIVER
LINK
TX
RX
TEST
ON
1234
E1IN
E1OUT
T1
GND
+Vin PWR
OPT
ICAL
FDXT1E1
S MA BT1/E1 CCITT
TRANSCEIVER
LINK
TX
RX
TEST
ON
1234
E1IN
E1OUT
T1
-
INS_FDXT1E1_REV11/07/12
PAGE 3
LED Indicators See Figure 8
FIGURE 2 FDXT1/E1/R3 IFS-Compatible R3 Units
Multimode Or Single Mode Optical Fiber (Depending On Model)
IFS R3 Rack Power Connections
REAR PANELFRONT PANEL
SIDE VIEW
Data Format and Test Switches See Figure 7
6-Pin Data Connector
DATA IN
DATA OUT
TEch SUPPORT: 1.888.678.9427
INSTALLATION AND OPERATION MANUAL FDXT1/E1(M,S)1(A,B)
-
INS_FDXT1E1_REV11/07/12
PAGE 4
FIGURE 3 FDXT1/E1 ComFit Unit Data Format Switch PositionsSwitches are located on front panel.
FIGURE 4 FDXT1/E1/R3 IFS-Compatible R3 Unit Data Format Switch PositionsSwitches are located on front panel.
TEch SUPPORT: 1.888.678.9427
INSTALLATION AND OPERATION MANUAL FDXT1/E1(M,S)1(A,B)
T1/E1 Mode
(Switch 1) Description
On T1 Mode
Off E1 Mode
Format (Switch 2) Description
On AMI Data Format
Off B8Zs Data Format
Test 0 (Switch 3)
Test 1 (Switch 4) Test Label Description
On On None N/A
Off On Optical Loopback (Analog) RX Fiber Input to TX Fiber Output Looped Back Internally through Analog Components
On Off Optical Loopback (Digital) RX Fiber Input to TX Fiber Output Looped Back Internally through Digital Components
Off Off Local Loopback (Analog) Loops Copper Received Data (P1, Pins 1 and 2) to Copper Transmit (P1, Pins 4 and 5)
Format (Switch 1) Description
On AMI Data Format
Off B8Zs Data Format
Test 0 (Switch 2)
Test 1 (Switch 3) Test Label Description
On On None N/A
Off On Optical Loopback (Analog) RX Fiber Input to TX Fiber Output Looped Back Internally through Analog Components
On Off Optical Loopback (Digital) RX Fiber Input to TX Fiber Output Looped Back Internally through Digital Components
Off Off Local Loopback (Analog) Loops Copper Received Data (P1, Pins 1 and 2) to Copper Transmit (P1, Pins 4 and 5)
GND
+Vin PWR
OPT
ICAL
FDXT1E1
S MA BT1/E1 CCITT
TRANSCEIVER
LINK
TX
RX
TEST
ON1234
E1IN
E1OUT
T1
T1/E1 Mode Select
Format Selection
Test 0
Test 1
Format Selection
Test 0
Test 1
-
INS_FDXT1E1_REV11/07/12
PAGE 5
FIGURE 5 T1/E1 DATA CONNECTIONS
CustomerEquipment FDXT1/E1A
CustomerEquipment
1 ST Fiber
FDXT1/E1B
Data Transmit
Data Receive
DIN()
DOUT()
DOUT()
DIN()
Data Receive
Data Transmit
TEch SUPPORT: 1.888.678.9427
INSTALLATION AND OPERATION MANUAL FDXT1/E1(M,S)1(A,B)
FIGURE 6 LED INDICATORS
LINK TX RX TEST
GREEN Unit In Sync Data Activity Data Activity Test Mode off (Normal operation)
RED Unit Not In Sync Test Mode on
oFF No Data Activity No Data Activity
-
INS_FDXT1E1_REV11/07/12
PAGE 6
INSTALLATION cONSIDERATIONS The comFit unit fiber-optic link is supplied as a Standalone/Rack module. Units should be installed in dry locations protected from extremes of temperature and humidity.
The R3 IFS-compatible unit fiber-optic link is supplied as a Rack module only, and should only be used in the IFS R3 rack. Units should be installed in dry locations protected from extremes of temperature and humidity.
c1-US, c1-EU, c1-AU OR c1-ch cARD cAgE RAckS cAUTION: Although the units are hot-swappable and may be installed without turning power off to the rack, comNet recommends that the power supply be turned off and that the rack power supply is disconnected from any power source. Note: Remove electrical connector before installing in card cage rack.
1. Make sure that the card is oriented right side up, and slide it into the card guides in the rack until the edge connector at the back of the card seats in the corresponding slot in the racks connector panel. Seating may require thumb pressure on the top and bottom of the cards front panel.
cAUTION: Take care not to press on any of the LEDs. 2. Tighten the two thumb screws on the card until the front panel of the card
is seated against the front of the rack.
WARNINg: Unit is to be used with a Listed class 2 power supply.
IMPORTANT SAFEgUARDS: A) Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly,
the operating ambient temperature of the rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) specified by the manufacturer.
B) Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment is not compromised.
MEchANIcAL INSTALLATION INSTRUcTIONS
2013 communications Networks corporation. All Rights Reserved. comNet and the comNet Logo are registered trademarks of communication Networks, LLc.
3 cORPORATE DRIvE | DANBURy, cT 06810 | USA T: 203.796.5300 | F: 203.796.5303 | TEch SUPPORT: 1.888.678.9427 | [email protected]
8 TURNBERRy PARk ROAD | gILDERSOME | MORLEy | LEEDS, Uk LS27 7LET: +44 (0)113 307 6400 | F: +44 (0)113 253 7462 | [email protected]
FIGURE ADimensions are for a standard ComNet one slot module
.156 [3.96 mm]
.313 [7.95 mm]
