Communication Lab Manual

Communication Lab Manual SSIT, Tumkur

COMMUNICATION LAB MANUALFOR

V SEMESTER B.E (E & C)(For private circulation only)

VISHVESHWARAIAH TECHNOLOGICAL UNIVERSITY

NAME: ___________________________

DEPARTMENT OF ELECTRONICS & COMMUNICATION


SRI SIDDHARTHA INSTITUTE OF TECHNOLOGY

MARLUR, TUMKUR-572105

CONTENTS

1. II-Order Low Pass and High Pass Active Filters

2. II –Order Band Pass and Band Elimination Filters

3. Attenuators

4. Collector Amplitude Modulation & Demodulation

5. Balanced Modulator

6. Class-C Tuned Amplifier

7. Frequency Modulation and Demodulation

8. Radio Receiver Characteristics

9. Pre & De – Emphasis Networks

10. AM IC Circuit-Modulation and Demodulation

11. Pulse Amplitude Modulation

12. Pulse Width Modulation

13. Pulse Position Modulation

14. Transistor Mixer


TESTING OF EQUIPMENTS BEFORE STARTING THECONDUCTION

1. OP AMP

Apply sine wave of amplitude 1

volt (1 kHz) as shown in ckt

diagram, if IC is good the output

be a square wave with peaks at +

VSAT and – Vsat.

2. 555 Timer :

If IC is good for the applied 5 V D.C supply as in

ckt diagram the voltage at pin no. 5 will be 2/3

Vcc (3.3 Volts)

3. Transistor

Identify emitter, base and collector of the

transistor, with DMM in diode position, if

transistor junctions are good it should indicate a

low resistance upon forward biasing emitter base junction or collector – base

junction and should indicate either OL or 1.(depending on DMM) upon

reverse biasing EB or CB junctions.

4. Source impedance of ASG:

1. Connect the DRB with the maximum resistance to ASG as in figure.

2. Adjust the amplitude of sine wave of 5V pp at 1 KHz.

3. Start reducing the resistance of DRB this reduces the output voltage also.

Source resistance Rs is that value of DRB resistance when the amplitude of

the output signal is half of the initial value. (2.5 V pp)

Rf

R

Communication Lab Manual

CIRCUIT DIAGRAM: -

II-Order Active Low Pass Filter

II-Order Active High Pass Filter

Design:- (LPF & HPF)

Assume Pass band gain AV = 2, Cutoff frequency fC = 5KHz

SSIT, Tumkur

1. Amplifier: AV = 1 + = 2, then Rf = R, choose Rf = R = 10KŸ

2. Filter Circuit : Cut off frequency fC =1

2R1C1= 5KHz

Choose C1 = 0.01Pf then R1 = 3.183 K � 3.3 K �

Rf = 10K, R� 1 = 3.3K, C� 1 = 0.01Pf, Op-amp =

1


Experiment No:

SSIT, Tumkur

DATE: __/__/____

II – Order Low Pass and High Pass Active Filters

AIM: - Design a second order Butterworth active low pass / high pass filter for a

given cut-off frequency fC = ______Hz. Conduct an experiment to draw frequency

response and verify the roll off.

PROCEDURE: -

1. Connections are made as shown in the circuit diagram.

2. Apply sine wave i/p signal of peak amplitude 5 volts.

3. Check the gain of non-inverting amplifier by keeping the frequency of the

input signal in the pass band of the filter. Note down the output voltage

VO max.

4. Keeping the input signal amplitude constant, vary the frequency until the

output voltage reduces to 0.707 Vo max, the corresponding frequency is

the cut-off frequency (fC) of the filter.

To find the Roll-off factor :-

1. For LPF :- Keeping the input signal amplitude constant, adjust the input

frequency at 10fC. Note down the output signal amplitude. The difference

in the gain of the filter at fC and 10fC gives the Roll-of factor.

2. For HPF :- Keeping the input signal amplitude constant, adjust the input

frequency at 0.1fC, note down the output signal amplitude. The difference

in the gain of the filter at fC and 0.1fC gives the Roll-of factor.

Conclusion:

2


Tabulation:

SSIT, Tumkur

High Pass Filter Vi p-p = Volts (Constant)

I/P frequency inHz

O/P VoltageVO P-P (volts)

Gain magnitude(Vo/Vi)

Gain magnitude in DB20log(Vo/Vi)

Roll off = - (G1 - G2) db/decade =

Frequency Response for High Pass Filter

3


Tabulation:

SSIT, Tumkur

Low Pass Filter Vi p-p = Volts (Constant)

I/P frequency inHz

O/P VoltageVO P-P (volts)

Gain magnitude(Vo/Vi)

Gain magnitude in DB20log(Vo/Vi)


Frequency Response for Low Pass Filter

Staff-in-charge:

4


CIRCUIT DIAGRAM: -

II-Order Active Band Pass Filter

II-Order Active Band Elimination Filter

Design:-

1. BPF : - R = 10K, R� f = 5.86 K, R� 1 = 1.989 K, R� 2 = 3.3 K,�C1 = 0.01Pf, C2 = 0.01Pf, Op-amp =

2. BSF : - R = 10K, R� f = 5.86 K, R� a = 3.3 K, R� b = 1.989 K,�C1 = 0.01Pf, C2 = 0.01Pf, Op-amp =

5


Experiment No:

SSIT, Tumkur

DATE: __/__/____

II – Order Band Pass and Band Elimination Active Filters

AIM: - Design a second order band pass and band stop active filter for a given

frequencies fC1 = ______Hz and fC2 = ______Hz. Conduct an experiment to draw

frequency response and verify the Roll off (Band Width = 3 to 5 KHz).

PROCEDURE: -


2. Apply sine wave i/p signal of peak amplitude 5 volts.

3. Check the gain of non-inverting amplifier by keeping the frequency of the

input signal in the pass band of the filter. Note down the output voltage

VO max.

4. Keeping the input signal amplitude constant, vary the frequency on either

side of pass band until the output voltage reduces to 0.707 Vo max, the

corresponding frequencies are the lower cut-off frequency (fL) and the

upper cut-off frequency (fH) of the filter.

To find the Roll-off factor :-

1. For LPF :- Keeping the input signal amplitude constant, adjust the input

frequency at 10fC, note down the output signal amplitude. The difference

in the gain of the filter at fC and 10fC gives the Roll-of factor.

2. For HPF :- Keeping the input signal amplitude constant, adjust the input

frequency at 0.1fC, note down the output signal amplitude. The difference

in the gain of the filter at fC and 0.1fC gives the Roll-of factor.

6


Design:

Specifications:

Pass band gain AV = 1.586, cut -off frequency fH = 5 KHz, fL=8 KHz, BW= 3 KHz

1. Amplifier:

Voltage gain AV = 1 + Rf / R = 1.586, choose R = 10K:,

Then Rf = 5.86 k: (use 5.6 k:+ 220 std value)

2. Filter:

Cut - off frequency fH= 1/2S R2C2= 5 KHz

Choose C2= 0.01Pf, then R2 = 3.183 k: (Select R2 = 3.3 k:)

Cut - off frequency fL = 1/2S R1 C1 = 8 k Hz

Choose C1= 0.01Pf, then R1= 1.989 k (Select R1 = (1.5 k: + 470:))

Tabulation:

Band Pass Filter Vi p-p = Volts (Constant)

FrequencyHz

O/P Voltage VO PP (volts) Gain (Vo/Vi)Gain in DB

20 log (Vo/Vi)Vomax =

fL = G1

0.1fL =10fH=

fH=

0.707 Vomax =

0.707 Vomax =

G2

G2’


Frequency Response for Band Pass Filter

7


Tabulation:

SSIT, Tumkur

Band Elimination Filter Vi p-p = Volts (Constant)

FrequencyHz

O/P Voltage VO PP (volts) Gain (Vo/Vi)Gain in DB

20 log (Vo/Vi)Vomax =

fL = G1

0.1fL =10fH=

fH=

0.707 Vomax =

0.707 Vomax =

G2

G2’


Frequency Response for Band Elimination Filter

Conclusion:

Staff-in-charge:

8


CIRCUIT DIAGRAM: -

T-Type Attenuator

Design:-

Specification: Vi = 5v, Vo = 2.5v, f = 1KHz

T- Type

SSIT, Tumkur

Attenuator

R1R O (N 1)

(N 1)R 2

R O 2N(N 2 -1)

RO =RS =600: (Assuming RS of ASG as 600:)

N = Attenuation factor = Vi / Vo = 2,

Therefore R1 = 200:, R2= 800:,

R1 = 200:, R2 = 800:, RL = 600:

Type

R1R O (N 2 1)

2NR 2

R O (N 1)(N -1)

RO=RS=600: (Assuming Rs. of ASG as 600:)

N = attenuation factor Vi / Vo = 2,

Therefore R1 = 450:, R2 = 1.8 K:.

R1 = 450:, R2 = 1.8 K:, RL = 600:

Type Vi volts VO volts N = Vi/VO

T-Type

9

R O

2R O 2


Experiment No:

SSIT, Tumkur

DATE: __/__/____

Attenuators – T, Lattice and O-Pad Types

AIM: - Design the attenuation circuits using T, O-Pad and Lattice type

networks to attenuate a given signal of amplitude _______volts and frequency

______Hz to be reduced to 50% of the amplitude. Test the circuit and record the

results.

PROCEDURE: -

1. Find the source resistance RS of ASG.


3. Adjust the amplitude of the input signal at 5VP-P at 1KHz.

4. Measure the amplitude of the output signal.

5. Find the attenuation factor N.

Design:-

1. T-Type attenuators:-

For N=2 and RS = RO = 600Ÿ, thenR1

R 2

(N -1)

(N 1)N

(N 1)

200

800

2. attenuators:-

For N=2 and RS = RO = 600 , thenR1

R 2

R O

R O

(N 2 -1)

2N

(N 1)

(N 1)

450

1.8K

10


Lattice-Type Attenuator

Design:-

Specification: Vi = 5v, Vo = 2.5v, f = 1KHz

Lattice- Type

SSIT, Tumkur

O-Pad Type Attenuator

R1R O (N 1)

(N 1)R 2

R O 2N(N 2 -1)

RO =RS =600: (Assuming RS of ASG as 600:)

N = Attenuation factor = Vi / Vo = 2,

Therefore R1 = 200:, R2= 800:,

R1 = 200:, R2 = 800:, RL = 600:

O-Pad Type

R1R O (N 2 1)

2NR 2

R O (N 1)(N -1)

RO=RS=600: (Assuming Rs. of ASG as 600:)

N = attenuation factor Vi / Vo = 2,

Therefore R1 = 450:, R2 = 1.8 K:.

R1 = 450:, R2 = 1.8 K:, RL = 600:

Type Vi volts VO volts N = Vi/VO

Lattice-Type

O-Pad Type

11

R O

2R O 2


Design:-

3. Lattice-Type attenuators:-

SSIT, Tumkur


R 2

(N -1)

(N 1)N

(N 1)

200

800

4. O-Pad Type attenuators:-


R 2

R O

R O

(N 2 -1)

2N

(N 1)

(N 1)

450

1.8K

Conclusion:-

Staff-in-charge:-

12


CIRCUIT DIAGRAM: -

Collector AM and Demodulation using Envelop Detector

Design:-

Specifications: -

Tuned frequency = fIFT, Assume fIFT = 455 KHz, t = 2.19

RC >> t, i.e., RC = 100 t = 0.219 msec

Choose C = 0.01 then R = 21.97 K, Select R = 22K (Std. value)� �

Envelope detector: -1

fm R1 C1

1

fc

Let R1C1 = 100 / fc ~ 0.219 msec

Choose C1 = 1 then R1 = 219:, Select R1 = 220 (std. value)

R1 = 220 C1 = 1 R = 22K:, C = 0.01Pf

Check point: -

Ensure that AFT is not loading the ASG.Check the transistor (See self checking)Adjust the carrier frequency exactly equal to fIFT.Observe the clamped signal at the base of the transistor.

13


Experiment No:

SSIT, Tumkur

DATE: __/__/____

Collector AM & Demodulation using Envelop Detector

AIM:- Conduct an experiment to generate an AM signal using collector

modulation for an fC = _______KHz and fm = _______Hz. Plot the variations of

modulating signal amplitude v/s modulation index.

PROCEDURE: -

1. Connections are made as shown in circuit diagram.

2. By switching off the modulating signal, find the tuned frequency of IFT by

varying the carrier signal frequency.

3. Keeping the carrier frequency the tuned frequency of IFT switch on the

modulating signal and observe the AM signal at the output of IFT.

4. Find the modulation index ‘m’, the amplitude of the carrier signal Vc and

the amplitude of the message signal Vm from the AM output by

measuring Vmax and Vmin.

Measure Vmax & Vmin

(i)

(ii)

from the AM o/p

from the Trapezoidal w/f

5. By varying amplitude of the modulating signal note down ‘m’, ‘Vm’, ‘Vc’

from Vmax and Vmin. Make sure that Vc is remaining constant.

6. Plot graph of Vm v/s % m.

7. Connect the envelope detector ckt to the IFT o/p and observe the

demodulated signal.

Note: To obtain the trapezoidal wave from, feed the modulating signal to

Channel ‘A’ and the modulated signal to channel ‘B’ of CRO and time / Div knob

in X via A position.

14

, ,


Tabulation:-

Modulation

Tuned frequency of IFT, fIFT = ____________KHz

SSIT, Tumkur

Sl.No Vmax (V) Vmin (V) m= Vmax - Vmin

Vmax Vmin

Vm = Vmax - Vmin

2 Vc = Vmax Vmin

2

Demodulation

Sl.No Vo (V) fo (Hz)

m (Vmax Vmin)(Vmax Vmin)

Vm (Vmax Vmin)2

Vc (Vmax Vmin)2

15

mL1 L2L1 L2


WAVE FORMS: -

(a) Carrier wave, (b) Sinusoidal wave, (c) Amplitude modulated signal.

Conclusion:-

Staff-in-charge:-

16


CIRCUIT DIAGRAM: -

Balanced Modulator (Using Diodes)

D1, D2, D3, D4 – OA79

Waveforms-

17

SSIT, Tumkur


Experiment No:

SSIT, Tumkur

DATE: __/__/____

Balanced Modulator (Using Diodes)

Aim:- Rig up a balanced modulator (Ring modulator) circuit. Test its operation

and record the waveforms.

Procedure: -


2. Apply the modulating signal (Sine wave) with frequency fm and the

carrier signal (square wave) with frequency fC (fC = 10 f m).

3. Observe the phase reversal of 1800 at each Zero crossing of modulating

signal in the output DSBSC signal.

Tabulation:-

Sl.No. VC Volts fC Hz Vm Volts fm Hz

Conclusion:-

Staff-in-charge:-

18

f


CIRCUIT DIAGRAM: -

Class-C Tuned Amplifier

SSIT, Tumkur

f Hz VO volts VDC volts IC mA RL ohms PAC

2VO

8R L

mWPDC VDC IC

mWPAC

PDC

Design:-

Specification:

Frequency f = 150 KHz, t = 6.66 usec

R1C1 >> t, i.e, R1C1 = 100 t

Choose C1 = 0.01Pf, the R1 = 66.6 K:.Select R1 = 68 K: (std value)

Tank ckt:

150KHz

If C = 0.001Pf, then L = 1.125 mH Then Factual = 159 KHz.

R1 = 68K:, C1 = 0.01Pf, C= 0.001Pf, L = 1mH

Check points: -Check the transistor (See self checking)Adjust i/p frequency exactly equal to tuned frequency.Observe the clamped signal at the base of the transistor.

19


Experiment No:

SSIT, Tumkur

DATE: __/__/____

Class-C Tuned Amplifier

Aim:- Design and test a Class-C Tuned amplifier to work at fO = ______KHz

(Center frequency). Find its maximum efficiency at optimum load.

Procedure: -

1. Connections are made as shown in circuit diagram.

2. Adjust the input frequency of the signal to get maximum output at theload.

3. For the applied DC voltage adjust the amplitude of input sine wave signalso that the output signal peak to peak amplitude is twice of the DC voltage(without any distortion).

4. Vary the load resistance RL around 10 KW.

5. Note Vo, VDC, IC and RL to find PAC and PDC hence the efficiency.

(Note: While measuring Vo, short the Ammeter connection)

Ideal graph:-

Conclusion :-

Staff-in-charge:-

20


Circuit Diagram: -

Frequency Modulation Circuit: -

Frequency Demodulation Circuit: -

SSIT, Tumkur

Sl.No fc Hz fm Hz Vm volts fcmax Hz fcmin Hz 1 Hz 2 Hz Hzf m

BT 2

1 f cmax - f c , 2 f c - f cmin , Max of 1 or 2

21


Experiment No:

SSIT, Tumkur

DATE: __/__/____

Frequency Modulation & Demodulation

Aim:- Design and conduct a suitable experiment to generate an FM wave using

IC8038. Find the modulation index and the bandwidth of operation BT. Display

the various waveforms.

Procedure: -


2. By switching off the modulating signal m(t), note down the carrier sine

wave of frequency of fC at pin 2 of IC 8038.

3. Apply the modulating signal m(t) with suitable amplitude to get

undistorted FM signal.

4. Note down maximum and minimum frequency of the carrier in FM signal

(i.e., fC max and fCmin)

5. Find the frequency deviation, modulation index & operation band width.

6. Test the demodulator circuit by giving FM output from IC8038 as an input

for the demodulator circuit.

22


Design-1: -

1. FM modulator circuit.

Let carrier frequency fC = 3 KHz, fC = 0.3/R Ct.

Choose R = 10KŸ = Ra = Rb, then Ct = 0.01Pf.

Take RL = 10KŸ, CC = 0.01Pf.

2. Demodulator using PLL.

Let fO = fC = 3 KHz, fO = 1.2/4R1C1.

Choose C1 = 0.001Pf, then R1 = 100KŸ.

Filter design: Let fm = 1 KHz = 1/2SRC

Choose C = 0.1Pf, then R = 1.59 KŸ 1.5 K �Design - 2: -

1. FM modulator circuit.

Let carrier frequency fC = 5 KHz, fC = 0.3/R Ct.

Choose R = 10K = R� a = Rb, then Ct = 0.001Pf.

Take RL = 10K, C� C = 0.01Pf.

2. Demodulator using PLL.

Let fO = fC = 3 KHz, fO = 1.2/4R1C1.

Choose C1 = 0.001Pf, then R1 = 100K.�Filter design: Let fm = 1 KHz = 1/2SRC

Choose C = 0.1Pf, then R = 1.59 K � 1.5 K �Wave Form: -

23


Design:-Specification:

Carrier frequency fC = 3 kHz, f c0.3

RC t

SSIT, Tumkur

Choose R= 10 KŸ, Ra = Rb, then Ct = 0.01Pf (use DCB)

Ra = Rb = 10 KŸ, RL = 10 KŸ, Ct = 0.01Pf (use DCB). R = 82 KŸ, CC = 0.01Pf.

Note: -Usually the carrier frequency of the FM signal is in the range of 100s ofKHz, but is chosen in terms of 1s of KHz to enable proper measurement of

frequency deviating

Check Points: -Ensure that a square wave and a triangular wave at pin 9 and 3 of IC 8038respective.

Conclusion :-

Staff-in-charge:-

24


Circuit Diagram: -

Radio Receiver: -

R = 10K:, C = 0.1Pf, RL = 100:

Selectivity: -

fm = _____Hz, %m = ______

SSIT, Tumkur

Sl.No fC Hz Vo volts

Fidility: -

fm = _____Hz, %m = ______

Sl.No fC Hz Vo volts

Sensitivity: -

fm = _____Hz, %m = ______

fC Hz Vi volts Vo volts

25


Experiment No:

SSIT, Tumkur

DATE: __/__/____

Radio Receiver CharacteristicsAim:- Plot the sensitivity/selectivity/fidelity graphs of a given AM Broadcast receiver inMW band by conducting suitable experiment.

Procedure: -


2. Ensure the Radio Receiver is in MW band.

3. Adjust the modulation index of AM signal at 30 % & fm = 400 Hz.

4. Let the receiver be tuned to 800 KHz. (can be anywhere between 540 KHz 1450KHz).

5. Keeping the carrier frequency of the AM signal at 800 KHz, observe thedemodulated signal and note down its amplitude.

Selectivity: -

1. Repeat the step 5 by changing the carrier frequency at 805, 810, 815 and 795,790, 785 KHz.

2. Plot a graph of carrier frequency of AM signal Vs the amplitude of the outputsignal (Vo Vs fc).

Sensitivity: -

1. Repeat the steps 1 to 5.

2. Vary the amplitude of the AM signal to get a standard value of output voltage(Volts). All the other parameters are kept constant (i.e., fc, fm, m). Note thechange in the amplitude of the output signal.

3. Repeat step 9 for different values of fc.

4. Plot a graph of amplitude of input signal v/s carrier frequency of AM signal (Viv/s fc).

Fidelity: -

1. Repeat the steps 1 to 5.

2. Vary the frequency of the modulating signal keeping all other parameters

constant (i.e., fc, VAM, m). Note the change in the amplitude of the output signal.

3. Plot a graph of amplitude of output signal Vs frequency of the modulating signal(Vo Vs fm).

Conclusion:-

Staff-in-charge:-

26


Circuit Diagram: -

Pre-emphasis

TABULATION: - Pre-Emphasis N/W

De-emphasis

SSIT, Tumkur

f Hz Vo volts GainVo

ViNormalized gain

Gain/GoNormalized Gain

In db

De-Emphasis N/W

f Hz Vo volts GainVo

ViNormalized gain

Gain/GoNormalized Gain

In db

27


Experiment No:

SSIT, Tumkur

DATE: __/__/____

Pre-emphasis and De-emphasis Networks

Aim:- Design and conduct an experiment to test a pre-emphasis and de-emphasis

circuit for 75Ps between 2.1KHz to 15KHz and record the results..

Procedure: -


2. Apply a sine wave of 5Vpp amplitude, vary the frequency and note down

the gain of the circuit.

3. Plot a graph of normalized gain Vs frequency.

Design: -

1. Pre-emphasis circuit.

Given f1 = 2.1 KHz, f2 = 15KHz.

f1 = 1/2SrC, f2 = 1/2SRC

Choose C = 0.1Pf then r = 820Ÿ and R = 100Ÿ.

Also r/R = Rf/R1, then R1 = 2.2KŸ and Rf = 15KŸ.

2. De-emphasis circuit.

fC = 1/2SRdCd.

Choose Cd = 0.1Pf and fC = f1 = 2.1KHz

Then Rd = 820Ÿ.

Conclusion :-

Staff-in-charge:-

28


Circuit Diagram: - AM Modulator using MC1496

AM Demodulator using MC1496

Tabulation:-

SSIT, Tumkur

Sl.No Vmax (V) Vmin (V) m=Vmax - Vmin

Vmax Vmin

Vm = Vmax - Vmin

2Vc = Vmax Vmin

2

29


Experiment No:

SSIT, Tumkur

DATE: __/__/____

AM – IC Circuit (Modulation & Demodulation)

Aim:- Using IC1496, rig up an AM modulation and Demodulation circuit. Test its

operation and record the waveforms.

Procedure: -

a) AM Modulation


2. Give the modulating signal of 2VPP (1KHz).

3. Give the carrier signal of 1VPP (600KHz).

4. Note down the AM modulated signal at pin 6 and also at the emitter of thebuffer (emitter follower).

5. Change the amplitude levels of the modulating signal, keeping fC and fm asconstant and find the depth of modulation.

b) AM Demodulation

1. Give the AM wave to pin1 of MC1496.

2. Also give the AM wave from the buffer o/p.

3. Note the demodulated signal at pin 12 of MC1496.

Design: -

Select Vdc = +12V, IC = 3mA. RL = + Vdc/ IC = 4KŸa3.9KŸ.

Vbe = 700mV, I = 160mA, Voltage at pin 5 = 1.7V.

Vbias = (-8+1.7) = -6.3V

RS = Vbias/I = 6.3/160mA = 7KŸa6.8KŸ

Conclusion :-

Staff-in-charge:-

30


Circuit Diagram: -

Pulse amplitude modulation and demodulation

Design: -

Specifications: -

IC = 1ma, hFE = 100, VCEsat = 0.3 V, VBEsat = 0.7v (assume), fm =

100hz.

SSIT, Tumkur

1. Biasing: -

2. Filter: -

Vm(t) = IC *RC + VCEsat ----- 1

Let Vm(t) = 2.5 v w.f peak + 3v DC shift = 5.5 V peak signal

Then Rc = 5.2 kŸ, select Rc = 4.7 k Ÿ(std. Value).

Vc (t) = IB*RB + VBEsat --------2

Let Vc(t) = 2 Vpp ( 1 V peak ) , Since IB = Ic / hFE = 10uA

Then RB = 30 k Ÿ

Select RB = 22 k Ÿ (Std. Value).

Cut off frequency of the filter fo >> fm

Choose fo = 500 Hz = 1 / 2 RC

Choose C = 0.1 f, then R = 3.3 k �Rc = 4.7 K R� B = 22k , R = 3.3k , C = 0.1Pf� �

Check Points: -

1. Ensure that square wave signal at the base of the transistor should haveamplitude > VJ.

2. Ensure that m (t) is having sufficient dc shift.

Tabulation: -

VC(pp) volts fC (Hz) Vm(pp) volts fm (Hz) Reconstructed output

31

VO volts fO (Hz)

1.

2.

3.

4.

5.

6.


Experiment No:

SSIT, Tumkur

DATE: __/__/____

Pulse Amplitude Modulation & DemodulationAim:- Conduct an experiment to generate PAM signal and also design a circuit todemodulate the obtained PAM signal and verify sampling theorem. Plot therelevant waveforms.

Procedure: -Connections are made as shown in the circuit diagram.

Apply the square wave carrier signal of 2V peak to peak amplitudewith frequency fc = 5 kHz.Apply sine wave modulating signal with frequency fm = 100 Hzwith 5 Vpp amplitude and 3 V DC shift (use function generator).

Observe the PAM output.

Observe the demodulated signal at the output of the low pass filter.

Repeat the steps 2 to 5 for fc = 2 fm & fc < 2 fm.

Waveforms:

Conclusion :-

Staff-in-charge:-

32


Circuit Diagram: -

Pulse Width modulation and demodulation

Pulse Width Demodulation

33

SSIT, Tumkur


Experiment No:

SSIT, Tumkur

DATE: __/__/____

Pulse Width Modulation & DemodulationAim:- Conduct an experiment to generate PAM signal and also design a circuit todemodulate the obtained PAM signal and verify sampling theorem. Plot therelevant waveforms.

Procedure: -


2. Keeping the modulating signal with minimum amplitude, observe theoutput of astable multivibrator with 50 % duty cycle at frequency fc.

3. Apply the modulating signal with frequency fm and the amplitude lessthan the critical amplitude observe the PWM signal.

4. Verify the variation of width of the pulses with respect to clampedmodulating signal (at point A).

To find the critical amplitude: -

As the amplitude of the modulating signal is increase the width of thepulses during the negative half of the modulating signal keeps on reducing andthat at the positive half of the modulating signal is increased the width of thepulses during the negative half of the modulating signal keeps on reducing andthat at the positive half of the modulating signal keeps on increasing.

34


Design: -

Specifications: -

Frequency fc = 1 KHz, duty cycle: 50 %

T = 1 ms, Ton = Tb= 0.5 ms

SSIT, Tumkur

I) Astable multivibrator: - Where RcH = charging resistance,

RDCH = Discharging Resistance,

Rf = Diode forward resistance

Ct = timing capacitor

TON = 0.69 (RCH + Rf ) Ct

Toff = 0.69 (RDCH + Rf) Ct

Ton = Toff = 0.5 ms

Choose Ct = 0.1 then (RCH + Rf) = (RDCH + Rf) = 7.246 k:

Assuming Rf of diode = 100:,

Then RCH = RDCH = 7.146 k: (use 6.8 k: + 330: std value)

II) Clamping ckt

Negative peak of the modulating signal clamped to zero

Rc >>1 /fm, fm = 100Hz

RC = 100 /fm, choose C= 10 f, then R = 100K.

RCH = RDCH = (6.8K + 330 ), R = 100K , Ct = 0.1 f, C = 10 f.

Check points: -With modulating signal zero, the voltage at pin 5 of 555 timer should be 2/3 VCC.

Ensure that modulating signal is clamped.

Tabulation: -

Unmodulated carrier PWM Output Demodulator

Tonms

Toffms fc Hz

Max.widthms

Min.widthms

Dynamicrangevolts

Modulatingfrequency

fm HzVO(V) fO(Hz)

35


Waveforms:-

Conclusion :-

Staff-in-charge:-

36

SSIT, Tumkur


Circuit Diagram: -

Pulse Position modulation and demodulation

Design:

m(t) = 1KHz, T = 1ms

T = RC, Let C = 0.01uf

Then R = 1 �

Pulse Position Demodulator

Design: -

Specifications: -

1. Monostable Multivibrator: -

PW = 1.1 Rch Ct

Choose Ct = 0.01 then Rch = 18.18 k (std. Value)

2. Differentiator : -

Rs * Cs <<1 / fc

Choose Rs * Cs = 0.01 ms, Choose Cs = 0.001Pf, then Rs = 10k

Rch = 18 k:. Ct = 0.01Pf, Rs = 10 k:, Cs = 0.001Pf

CHECK POINTS: -

With modulating signal zero, the voltage at pin 5 of 555 timer should be 2 /3 Vcc.

Ensure that wave form at pin 2 of 555 timer should have a trailing edge going below 1/3 Vcc.

37


Experiment No: DATE: __/__/____

SSIT, Tumkur

Pulse Position Modulation & DemodulationAim:- Conduct an experiment to generate PAM signal and also design a circuit todemodulate the obtained PAM signal and verify sampling theorem. Plot therelevant waveforms.

Procedure: -


2. Check the working of 555 timer as a monostable multivibrator by giving anunmodulated PWM signal. Verify the pulse width of output signal for thedesigned value.

3. By applying the PWM signal note the change in the position of the pulses i.e.PPM signal.

4. Critical amplitude of the modulating signal is that value of m(t) at which thepulse in PPM just disappears.

Waveforms:-

Conclusion:-

Staff-in-charge:-

38


Circuit Diagram: -

Transistor Mixer

Design: -

Specifications: -

VCC = 6V, VCE = 5V, assume IC = 1ma, hFE = 100, VBEsat = 0.6v.

VCC = VCE + IE * RE

Since IE ~ IC, then RE = 1 K:

Vb = IB * RB + VBEsat + IE * RE ------ (1)

Where Vb = VCC * R2 /R1 + R2, RB = R1 + R2, RB = R1 * R2 /R1 + R2

From eq (1) it can be found that R1 ~ 2.5 R2, Choose R2 = 18 K:, then R1 45 K:

R1 = 47 K:, R2 = 18 K:, RE = 1K:, CC = 0.1:f, CE = 10Pf

Check points: -

During the mixer operation under on circumstance the frequency of local oscillator or

frequency of the carrier should be kept at tuned frequency of IFT. (i.e., fLO = fIFT = fS)

Tabulation: -

fIFT = __________, Vmax = ___________, Vmin = _________, %m = __________

Operation fS Hz fLO Hz fO Hz fLO + fS Hz

Up Conversion

Down Conversion

39

1.

2.

3.

4.

5.

6.


Experiment No: DATE: __/__/____

SSIT, Tumkur

Transistor MixerAim:- Conduct an experiment to generate PAM signal and also design a circuit todemodulate the obtained PAM signal and verify sampling theorem. Plot therelevant waveforms.

Procedure: -

Connections are made as shown in the circuit diagram.

Keeping the amplitude of the local oscillator in minimum position, find the

tuned frequency of IFT (fIFT) by varying the carrier frequency (fs) of theinput AM signal.

Down conversion: -

Adjust the carrier frequency of the AM signal more than the tuned

frequency of IFT, now adjusting the local oscillator frequency (fLO = fs +

fIFT)

(Note: local oscillator amplitude 0). Observe the output AM signal with

carrier frequency at fIFT.

Repeat the step 3 for different carrier frequencies.

Up conversion: -

Adjust the carrier frequency of the AM signal less than the frequency of

IFT, now adjusting the local oscillator frequency (f LO = fS + f IFT) (Note :

local oscillator amplitude 0). Observe the output AM signal with carrierfrequency at f IFT.

Repeat the step 5 for different carrier frequencies.

Formulas: Zo = Vo rms/Io, gc = Vo rms/ (Vi rms.Zo)

Conclusion:-

Staff-in-charge:-

40

Communication Lab Manual

Documents

Transcript of Communication Lab Manual