COMBI 3000 10' Automated Slab Saw Stone Sawimerusa.com/pdf/COMBI_3000_14inch.pdfsystem delivers...
2
Quality Aircraft quality materials make for a rigid and light weight saw which will maintain its accuracy and finish for years to come. Power The 4 HP. motor, combined with the serpentine drive belt reduction system delivers plenty of cutting power - standard granite slabs are cut in 4 to 5 minutes! The 4 h.p. motor runs on 220v 20 amp single phase electrical power. The motor has a belt reduction system that is fully enclosed and self tensioning. The Water Tub The water tub is easy to access and clean after a day of fabrication. Just roll it out from under the saw and empty. COMBI 3000 10' Quick Specs Blade diameter 14" Blade shaft diameter 1" Maximum cutting length 10' Maximum cutting depth 90/45 degrees 4-3/4" / 2-1/3" Motor rating 4 h.p. Blade speed 2,250 r.p.m. Cutting table dimensions 10' x 2.5' Current required 220v, single phase, 20 amp Water pump flow 4 g.p.m. Water tub capacity 25 gals. Noise level 78 db(A) OPERATING (CRATED) DIMENSIONS Width 43" (48") Length 13'5" (13') Height 5'8" (5'8”) IMER’S COMBI 3000 is an affordable alternative to large stationary bridge saws which require a lengthy set-up procedure and cost thousands and thousands more than the COMBI 3000. It’s easy to set up, simple to operate, yet just as accurate and smooth cutting as the more Stone Saw Accuracy When cutting full-size slabs the protractor is just not enough to accurately position the stone. The COMBI 3000 has an addi- tional fence system that runs the length of the saw. This fence is fully adjustable and locks in place quickly and accurately. Laser Guide A laser cutting guide now comes standard with every COMBI 3000. Mark the line of your cut on the slab, line it up with the laser, clamp it down and go! COMBI 3000 10' Automated Slab Saw 10 Contractors Speak Up The Combi 3000 got me up and running in the slab fabrication business. In 4 years I have made enough to purchase a fully automated very sophisticated sawing system. I even sold my used 3000 for good money. The Combi 3000 is a fantastic start-up saw! – I.W. Seo, owner of Seo Tile & Marble, Beltsville, MD Clamping System Two high quality full size slab clamps come with each saw. Clamps are positioned at each end of the saw to ensure that the slab is locked down good n’tight.
Transcript of COMBI 3000 10' Automated Slab Saw Stone Sawimerusa.com/pdf/COMBI_3000_14inch.pdfsystem delivers...
QualityAircraft quality materials make for a rigid and light weight saw which will maintain its accuracy and fi nish for years to come.
PowerThe 4 HP. motor, combined with the serpentine drive belt reduction system delivers plenty of cutting power - standard granite slabs are cut in 4 to 5 minutes! The 4 h.p. motor runs on 220v 20 amp single phase electrical power. The motor has a belt reduction system that is fully enclosed and self tensioning.
The Water TubThe water tub is easy to access and clean after a day of fabrication. Just roll it out from under the saw and empty.
COMBI 3000 10' Quick Specs
Blade diameter 14"
Blade shaft diameter 1"
Maximum cutting length 10'
Maximum cutting depth 90/45 degrees 4-3/4" / 2-1/3"
Motor rating 4 h.p.
Blade speed 2,250 r.p.m.
Cutting table dimensions 10' x 2.5'
Current required 220v, single phase, 20 amp
Water pump flow 4 g.p.m.
Water tub capacity 25 gals.
Noise level 78 db(A)
OPERATING (CRATED) DIMENSIONS
Width 43" (48")
Length 13'5" (13')
Height 5'8" (5'8”)
IMER’S COMBI 3000 is an affordable alternative to large stationary bridge saws which require a lengthy set-up procedure and cost thousands and thousands more than the COMBI 3000. It’s easy to set up, simple to operate, yet just as accurate and smooth cutting as the more
Stone Saw
AccuracyWhen cutting full-size slabs the protractor is just not enough to accurately position the stone. The COMBI 3000 has an addi-tional fence system that runs the length of the saw. This fence is fully adjustable and locks in place quickly and accurately.
Laser GuideA laser cutting guide now comes standard with every COMBI 3000. Mark the line of your cut on the slab, line it up with the laser, clamp it down and go!
COMBI 3000 10' Automated Slab Saw
10
Contractors Speak UpThe Combi 3000 got me up and running in the slab fabrication business. In 4 years I have made enough to purchase a fully automated very sophisticated sawing system. I even sold my used 3000 for good money. The Combi 3000 is a fantastic start-up saw!– I.W. Seo, owner of Seo Tile & Marble, Beltsville, MD
Clamping SystemTwo high quality full size slab clamps come with each saw. Clamps are positioned at each end of the saw to ensure that the slab is locked down good n’tight.
The Combi 3000 arrives in a crate and is 99% assembled. If our trusty IMER Sales Reps can get it up and running in 2 hours… anyone can!
complicated stationary bridge saws. Built for the start-up shop, or a full size shop needing on site fabrication and a versatile complement to their existing shop saw, the COMBI 3000 is the perfect sawing system.
11
Gordon Comrie and Pete Thompson are all smiles after another smooth Coverings Show set-up at the Orlando Florida Convention Center.
Computer ControlledA computer for automated current control ensures that the speed of cut and motor amperage draw are always at optimal levels. The gear drive advancement system is the most reliable made. Fast, accurate, chip free cuts are automatic, pass after pass.
ReliabilityThe travel bar is built like a suspension bridge, with pre-tensioned bars anchored within it. This provides great reliability and accuracy, cut within a 1/32" over 10 feet.
Toughness & PortabilityThe COMBI 3000 is built extremely well. Use the forklift hoist slots to move the 3000 around the shop, or load it up and take it to the jobsite!
User FriendlyThe controls for a fully automated saw have never been more user friendly. Operating the COMBI 3000 is not rocket science - new operators can be trained and up to cutting speed in an hour or two.
Fully AutomatedThe COMBI 3000 has a computer on board which senses if the stone being cut becomes denser in certain spots. The computer will automatically ensure that additional amperage is sent to the motor, preventing stalling or pinching.
VersatilityThe saw head also has the ability to chop up and down, plunge cuts up to 4 3/4" are possible.
Handling SystemTwo roller tables are included with every saw. This makes handling the slabs much easier.
Cutting 45°Tilting to 45 degrees is easy, simply feather the hydraulic control lever and the saw gently rotates over to 45 degrees. To return the saw to 90 degrees, pump the hand lever 4 or 5 times. Simple, safe and accurate.
