Com624 Manual

this document downloaded from

vulcanhammer.netSince 1997, your complete on-line resource for information geotecnical engineering and deep foundations:The Wave Equation Page for Piling

The historical site for Vulcan Iron Works Inc.

Online books on all aspects of soil mechanics, founda-tions and marine construc-tion

Free general engineering and geotechnical software

And much more...

All of the information, data and computer software (“information”) presented on this web site is for

general information only. While every effort will be made to insure its accuracy, this information should

not be used or relied on for any specific applica-tion without independent, competent professional

examination and verification of its accuracy, suitability and applicability by a licensed profes-

sional. Anyone making use of this information does so at his or her own risk and assumes

any and all liability resulting from such use. The entire risk as to quality or usability

of the information contained within is with the reader. In no event will

this web page or webmaster be held liable, nor does this web page or its webmaster provide insurance

against liability, for any damages including lost profits, lost savings or

any other incidental or consequential damages arising from the use or

inability to use the information contained within.

This site is not an official site of Prentice-Hall, Pile Buck, the Univer-

sity of Tennessee at Chattanooga, Vulcan Foundation Equipment or

Vulcan Iron Works Inc. (Tennessee Corporation). All references to

sources of software, equipment, parts, service or repairs do not

constitute an endorsement

Terms and Conditions of Use:

Visit our companion site

http://www.vulcanhammer.org

http://www.vulcanhammer.net/

http://vulcanhammer.org/

NOTICE

This document is disseminated under the sponsorship of the Department of Transportation in the interestof,information exchange. The United States Government assumes no liability for its contents or usethereof. The United States Government does not endorse products or manufacturers. Trademarks or _manufacturers’ names appear herein only because they are considered essential to the object of thisdocument.

CHAPTER 1. GENERAL

The documentation for Computer Program COM624P consists of

three documents: Part I, Users Guide; Part II, Engineering

Background; and Part III, Systems Maintenance.

PURPOSE OF TEE USERS GUIDE

The purpose of Part I of COM624P is to provide detailed

information to enable the user to employ the program conveniently

and effectively. The project was conducted under Contract DTHF61-

88-C-00101 from 1988-1989. The information is presented as

follows: Chapter 1 introduces the Users Guide and provides system

background; Chapter 2 summarizes the system in general; Chapter 3

provides a step-by-step operating procedure; Chapter 4 presents

input information, names of variables, and data structure for the

input files; and Chapter 5 presents input and output for examples

that were studied.

PROJECT REFERENCES

The technology on which the program is based has been widely

used for many years for the analysis of a variety of piles

subjected to lateral loads. The existing program, COM624, was

developed at the The University of Texas at Austin and has been

used on main-frame computers for several years. The project is to

upgrade COM624 and to develop a user-friendly version for running

on IBM XT's, AT's, and compatible microcomputers. The first

version of Program COM624P (Version 1.0) has been used and

distributed by FHWA since 1990. Because of a number of inquiries

by design engineers about the ultimate capacity of a pile in

bending, a subroutine has been added to the current version (2.0)

to compute the ultimate capacity in bending and the variation of

flexural rigidity with applied moment.

1

The information shown in the three parts of the documentation

is limited to that needed for the operation of the computer

program and to a brief introduction of the method of analysis.

The user is referred to two documents published by the Federal

Highway Administration for a relatively complete treatment of the

topic. The first one is entitled "Behavior of Piles and Pile Groups under Lateral Load" (FHWA/RD-85/106). The second one is entitled "Handbook on Design of Piles and Drilled Shafts Under

Lateral Load" (FHWA-IP-84-11).

SECURITY

This project is conducted under the sponsorship of the United

States Department of Transportation. Under the United States

Copyright Act of 1976, no part of this document or accompanying

software may be reproduced, translated, or distributed without the prior approval of the Department of Transportation.

No warranty, expressed or implied, is offered either by FHWA

or Ensoft, Inc., as to the accuracy of results from the program.

The program should not be used for design unless caution is

exercised in interpreting the results, and independent

calculations are available to verify the general correctness of

the results. The user is assumed to be knowledgeable of the

information in the documentation that accompanies the diskettes.

The user is assumed to recognize that the input parameters can

have a significant effect on the solution and must be chosen

carefully.

2

CHAPTER 2. SYSTEM SUMMARY AND PROGRAM STRUCTURE

SYSTEM APPLICATION

The design of driven piles and drilled shafts under lateral

loading is an important problem and one that is encountered

frequently in highway design. The principal use of piles or

drilled shafts in highway structures is for the support of

bridges, either to span water courses or to serve in interchanges.

Other applications using laterally-loaded piles on highways can be

seen in bridge abutments, overhead signs, pile-supported retaining

walls, and pile-stabilized slopes.

Computer program COM624P is used to analyze the behavior of

piles or drilled shafts which are subjected to lateral loads. The

method of analysis implemented in COM624P is the so-called p-y

method. The theoretical background about the p-y method of

analysis is described in Part II of this document. The digital

computer allows the deflected shape (lateral deflection) of a pile

to be computed rapidly and accurately by iteration even though the

soil reaction against the pile is a nonlinear function of pile

deflection. After the deflection is determined, the shear,

bending moment, and soil resistance along the pile can be computed

thereafter. With the availability of microcomputers, this program

makes it possible for highway engineers to employ the rational p-y

method for analysis of laterally-loaded piles and drilled shafts.

SYSTEM COMPONENTS

The package sent with COM624P, in general, contains three

5.25-inch double-sided, double-density floppy diskettes. The

first diskette contains the main program of COM624P.EXE and six

sample-data files: Example.INl through Example.ING. The engineer

may use the sample data to run COM624P and check the solutions

3

presented in Chapter 5. If there are significant discrepancies,

the user should report to FHWA immediately.

The second diskette contains the screen-editing files. The

files stored in this diskette are: C624EDIT.EXE., C624EDIT.HLP,

C624EDIT.CFG, PILEDATA.LIB, and INSTVIEW.EXE. The engineer may

use a preprocessor program named C624EDIT.EXE to create a new data

file, retrieve, and edit an existing data file.

The third diskette contains the graphics package. The files

stored in the diskette are C624VIEW.EXE., C624EDIT.CFG,

INSTVIEW.EXE, and EXAMl.PLT. The main graphics program is named

C624VIEW.EXE. The user may execute this program and assign the

data created by COM624P for graphics display.

SYSTEM PROCESSIWG

The system consists of three modules as described earlier. To

process the system, the user starts to load the Menu and selects

the preprocessor program C624EDIT.EXE to create an input-data

file. C624EDIT can also be used to retrieve an existing data file

and to edit the data entry. After the data file has been created

or corrected, the user should save the data file using the SAVE

command.

The second step of processing the system is to call the main

program COM624P. COM624P will process the data file that contains

the user's input data, and will create a text-output file and a

graphics-output file. The user may view the output data on the

monitor or print the output file to get a hard copy. If the user

prefers to have a graphics display, then the program C624VIEW

should be viewed. C624VIEW will display the graphics based on the

computed results, and the user can get a hard copy of graphics

from the installed HP plotter or dot-matrix printer. A flow chart

4

depicting data flow and showing the relationships of each module

is presented in Fig. 2.1.

SYSTEM CONFIGURATION

Program COM624P was develaped for the IBM-XT and IBM-AT or

for any microcomputer that is compatible with the IBM. The

program has been checked for conformance with ANSI FORTRAN77. The

Fortran Compiler from Microsoft, Inc., was used to compile the

source code and create the execution file.

The word length is important for convergence to a solution

of the nonlinear equations employed by this program. Therefore, a

double-precision real value, occupying 8 bytes of storage, was

used in the Fortran Code. The precision is approximately 15

decimal digits. If a value has more digits, only the first 15 are

significant.

The program requires at least 256k of RAM memory. The math

coprocessor is highly recommended but is not required. If a high-

speed, floating-point math coprocessor is installed, the execution

time for a normal problem is less than one minute. However, it

can take 3 to 7 minutes for the same problem, depending on the

type of microcomputer, if the math coprocessor is absent. The

operating system that is required to run the program should be MS-

DOS 2.1 or a later version.

The preprocessor for input data, C624EDIT; and the post-

processor for graphics display, C624VIEW, were developed in the

Pascal language to utilize fully the screen-control function

provided by most microcomputers. Two peripheral devices are

required to run C624VIEW. One is a graphics adapter which can

change the screen to the graphics mode for plotting output.

Currently, the program supports the following graphics adapters:

5

SYSTEM 0 Prepare Input Data

C624EDlT.EXE Create an Input File

Run Main Program COM624P.EXE

Create Text Output 81 Graphics Output

Send Text Output Process Graphics Data to C624VIEW.EXE

Printer Create Graphics Plots

6

CGA - IBM Color-Graphics Adapter Driver EGA - IBM Enhanced-Graphics Adapter Driver VGA - Video Graphics Array Adapter HERC - Hercules Driver AT&T - AT&T 400 Line Driver

The other peripheral equipment is a printer or plotter for

hard copies of graphics. The program supports HP plotters; the

IBM proprinter; Epson MX, FX, LX, LQ or Epson compatible printers

including Okidata, Panasonic, and Star printers.

MAIN PROGRAM STRUCTURE

The structure of the main program COM624P is shown in the

flow diagram Fig. 2.2. The function of each subprogram is

described in the following listing.

1. Main Program

Function: the main program COM624P inputs and outputs a small amount of data, but mainly controls the flow of logic by calling appropriate subroutines.

Calls: UNITSS, NODEM INPT, OPIN, NODE, .FLXRIG, DEFLEC, ESCALL, DISTR, MCALC, OPCHK, EQUIL, PYGEN, PMEIX

2. UNITSS

Function: to store table headings.

Called From: COM624P

Calls: none

7

START 4 CALL INPUT

t CALL OPIN

t

Figure 2.2. The flow chart of Main Program COM624P.

8

3. INPT

Function: this subroutine reads most of the technical data for the problem.


Calls: none

4. OPIN

Function: this subroutine outputs the data for a problem.


Calls: none

5. NODE

Function: this subroutine (1) calculates the coordinate for each node, (2) calculates the number of the node at the top and bottom of each layer of soil, and (3) initializes the array of soil moduli.


Calls: none

6. FLXRIG

Function: this subroutine calculates the flexural rigidity of the pile at each node.


Calls: none

9

7. DEFLEC

Function:

Called By:

Calls:

a. DISTR

Function:

Called By:

Calls:

9. MCALC

Function:

Called By:

Calls:

10. OPCHK

Function:

Called By:

subroutine DEFLEC calculates deflection at all points along the pile.

COM624P

none

this subroutine calculates distributed load relevant to each node.

COM624P

none

this subroutine computes the moment, soil reaction, and combined stress in the pile at each node along the pile.

COM624P

FUNCTION D

this routine calculates the imbalance in force and moment at a node.

COM624P

Calls: none

10

11. OUTPT

Function:

Called By:

Calls:

12. EQUIL

Function:

Called By:

Calls:

COM624P

none

13. INPY

Function: this subroutine computes values of soil modulus from input p-y curves.

Called By:

Calls:

ESCALL

none

14. FUNCTIONS C, D, GAM, E50, CAVG, AS, AC, SANDAB, PHI

subroutine OUTPT prints the information from final solution, including a table of depth, deflection, moment, maximum combined stress in the pile, distributed load, soil modulus, and flexural rigidity.

COM624P

none

this subroutine (1) computes boundary conditions and prints them to facilitate checking and (2) computes and prints overall force and moment imbalance.

Functions: these function subroutines do the following:

FUNCTION C computes the value of cohesion at any depth by linear interpolation from input data.

FUNCTION D computes the pile diameter at any depth.

FUNCTION GAM computes the average effective unit weight of soil above a point.

11

FUNCTION ES0 computes the & 50 (strain at a stress ratio of 50 percent) by linear interpolation from input data.

FUNCTION CAVG computes the average shear strength of soil above a point,

FUNCTION AS computes the coefficient A, for stiff clay below the water table.

FUNCTION AC computes the coefficient A, for stiff clay below the water table.

FUNCTION SANDAB computes coefficients A and B for sand.

FUNCTION PHI computes angle of internal friction at any depth.

Called By: these functions are called in the subroutines

that generate p-y curves (SOFTCL, STIFFA, STIFFB, and SAND).

Calls: none

15. PYGEN

Function: this subroutine reads information needed to generate p-y curves, stores data for each layer, and calls ESCALL to generate p-y curves.

Called By: COM624P

Calls: ESCALL

16. ESCALL

Function: subroutine ESCALL calls the appropriate subroutine for calculation of soil modulus or generation of p-y curves for verification purposes.

Called By: COM624P, PYGEN

Calls: SOFTCL, STIFFB, STIFFA, SAND, INPY

12

17. SOFTCL

Function: this subroutine generates p-y curves for output verification and calculates secant soil modulus at all nodes in soil with KSOIL = 1 (internally- generated p-y curves in soft clay with Matlock's (1970) recommendations).

Called I By: ESCALL

Calls: Functions D, C, GAM, ES0

18. STIFFB

Function: this subroutine generates p-y curves for verification of output and calculates secant soil modulus at all relevant nodes where KSOIL = 2 (stiff clay below the water table with criteria by Reese et al., 1975).

Called By: ESCALL

Calls: Functions D, C, CAVG, GAM, E50, AS, AC

19. SAND

Function: this subroutine generates p-y curves for verification of output and calculates secant soil modulus at all relevant nodes where KSOIL = 4 (internally-generated p-y curves in sand with criteria by Reese et al., 1974).

Called By: ESCALL

Calls: Functions D, GAM, PHI

13

20. STIFFA

Function: this subroutine generates p-y curves for verification of output and calculates secant soil modulus at all relevant nodes when KSOIL = 3.

Called By: ESCALL

Calls: Functions D, C, CAVG, GAM, and E50

21. ROCK

Function: this subroutine generates p-y curves for verification of output and calculates secant soil modulus at all relevant nodes where KSOIL = 6 (internally-generated p-y curves in rock with limestone criteria by Reese and Nyman, 1978).

Called By: ESCALL

Calls: Functions, D, C, CAVG, GAM, E50

22. LAYERS

Function: this subroutine calculates the equivalent thickness of soil layers for use in the theory for the behavior of layered soil.

Called By: SOFTCL, STIFFB, STIFFA SAND ,

Calls: none.

23. PMEIX

Function: this subroutine calculates the ultimate bending capacity and variation of flexural rigidity based on given data on cross section.

Called By: COM624P

Calls: SETUP, CSTRES, STEELP, SHELLP, SHELLM, COREP, COREM.

14

CHAPTER 3. GUIDE FOR EXECUTION OF COM624P ON A MICROCOMPUTER

COM624P was written with user-friendly features such as menu

input, free-field format, and screen editing. The output can be

sent to printers for hard-copy or sent to plotters for display Of

graphics. This section describes the step-by-step procedures t0

operate the system.

Operation of COM624P consists of three steps. The first step is the creation of input-data files using the user friendly input

menus or an ASCII input batch file using a text editor. After an input file has been created execute the program by selecting the

"Run w menu or typing COM624P.EXE for batch file execution. The procedures for each step are described in the following paragraphs.

BACKING UP AND RESTORING ORIGINAL DISKETTE

The user is assumed to have basic knowledge on how to use the

operating system (DOS) for selected microcomputers. Before

operating, a backup copy should be made for each original diskette

and the original diskettes should be stored in a safe place.

To make a backup of the entire diskette, the user can use the

following steps:

1. Format a regular blank floppy diskette using the FORMAT

command on the DOS operation system.

2. Insert the original diskette in Drive A, and the

formatted diskette in Drive B, then enter the following:

15

A:> COPY A:*.* B: <CR>

(Note: <CR> represents the enter or return key)

3. If the user has a hard disk installed in the computer,

use the following instructions to create a COM624P directory and

save all the files onto the hard disk:

c:> MD COM624P <CR>

(Note: create a directory)

C:> CD COM624P <CR>

(Note: change main directory to COM624P directory)

C:\COM624P>COPY A:*.* <CR>

(Note: copy files from the original diskette in Drive A to

the hard disk in Drive C)

GUIDE FOR INSTALLATION OF CONFIGURATION FILE

The program named INSTVIEW.EXE is used to create the

configuration file used for video attributes and graphics drivers.

The file produced by INSTVIEW is named C624EDIT.CFG. The

configuration file must be kept on the same disk directory that

contains C624EDIT.EXE and C624VIEW.EXE.

If these files are on Drive C, then enter the following:

C:\COM624P>INSTVIEW.EXE <CR>

16

INSTVIEW will begin and will ask the user to make selections

regarding units of data, graphics hardware, Graphics Mode, and

video attributes. The following sections discuss the information

requested by INSTVIEW.

The first input screen presented by INSTVIEW is the values

for control parameters denoted by COM624P. The default values are provided as shown in the following. The user can change the preset values, if it is necessary. For example, an input value of 2 for units will cause COM624P to display SI units instead of

English units When the user is satisfied with the selection, the

F8 key should be pressed to continue to the selection of the

graphics driver and Graphics Mode.

C624EDiT Configuration File Editor

-Units, 1 = lb&inch, 2 = metric, 3 = other p-y Curve Criteria: 0 = cyclic, 1 = static i Print full pile response: 0 = off, 1 = on Print p-y curves: 0 = off, 1 = on . . . . . . . . . i Iterations Limit for Analysis . . . . . . . . . . . . . 100 Convergence tolerance for pile analysis . . . 0.000100 Back-up data files: 0 = off, 1 = on . . . . . . 1 Pile Property Library Path & Name . . . . . . . . B:PILEDATA.LIB

A 1:DEF:Num 1

: Move Cell - ? : Help - F2 : Edit Cell - F8 : Continue - d

17

The second input screen presented by INSTVIEW is the menu

from which the graphics driver is selected. The graphics drivers that are supported are:

(1)

(2)

(3)

(4)

(5)

(6)

(7)

(8)

CGA

MCGA

EGA (256K memory version)

EGA (64K memory version)

EGA driving monochrome monitors

VGA

IBM 8514

AT&T

(9) Hercules monochrome

(10) IBM PC3270

Graphics Drivers

(1) Color Graphics Adapter (CGA) (2) MCGA (3) 16 Color Enhanced Graphics Adapter (4) 4-Color Enhanced Graphics Adapter (5) EGA driving Monochrome Display (6) IBM-8514 Graphics Card (7) Hercules Monochrome Graphics Adapter (8) AT&T 400-Line Graphics Adapter (9) Virtual Graphics Array (VGA) (10) IBM PC3270 Graphics

(11) Accept this selection

Current Selection is VGA

Enter new selection: 11

All of the above graphics drivers, with the exception of the

IBM PC3270 and Hercules monochrome, can be driven in a variety of

modes. After the graphics driver has been selected, a third input

18

screen is presented for the selection of the Graphics Mode. - The Graphics Mode controls the combination of pixel densities and

colors used by COM624P.

,

Graphics Modes for VGA

(1) 640x200 16-Color (2) 640x350 16-Color (3) 640x480 16-Color

(4) Accept this selection',

Current Selection is 0)

Enter new selection: 4

The next screen is to specify plotting-control values and the

printing device in the system, as shown below. It should be noted

that all the printer output will be sent to port LPTl. If the

setup in the system is different, the user can use DOS MODE

command to redirect the printer port.

I I Optional Plotting Control Values

Axis Title Character Size (IN) . . . . . . . . . . . . . . Plotting Symbol Size (IN) . . . . . . . . . . . . . . . . . . . Plotter Pen Number for Axis Titles . . . . . . . . . . Plotter ,Pen Number for Axis and Borders . . . . . Plotter Pen Number for Data Line & Symbols . . Type of Printer Used for Screen Dump . . . . . . . . Codes for printers: 1 = Epson MX, FX

:: = Epson LQ = Toshiba 24-pin

4 = HP LaserJet and DeskJet 5 = HP InkJet 6 = IBM Proprinter 7 = IBM Proprinter

0.15000 0.15000

i

t

All printer output is sent to LPTl. To redirect LPTl to COMl use the DOS MODE command.

A 1:DEF:Nwn I- 0.15000

: Move Cell - 7 : Help - F2 : Edit Cell - F8 : Continue -I

19

The final input screen presented by INSTVIEW is the

interactive selection of the video attributes used in the screen

menus. The user may use this feature to customize the colors used

by Menu to suit his or her personal tastes. Five video attributes

may be selected. They are the color schemes used on Menu

backgrounds, the highlighted letter choices, the current Menu

selections and the data-entry cells (both active and inactive).

This interactive section shows an example of the current

selections so that the user can appraise the selections and avoid

confusing combinations of color. Users running the program on systems with monochrome monitors have a smaller range of selections, but still have a wide variety of possible selections.

Selections for the video attributes are made by moving the

box to the desired combination of letter color and background

color, then by pressing the appropriate Function Key (Keys Fl

through F5). The user may change any of the selections as desired. The user then presses the Escape Key when satisfied with

the current selections for the video attributes.

The last step of the installation process is for the user to

indicate acceptance of the current configuration for COM624P. If

the user is satisfied, 'Y' or 'y' should be entered for yes. If a

'yes I response is given, COM624P will write the new version of

C624EDIT to the current directory and indicate that it has been

changed. If the user enters an answer other than 'yes', the

program exits without saving a new configuration file.

20

MENU STRUCTURE

COM624P, Version 2.0, uses the window feature and pull-down- menu interface for easy learning and operation. Figure 3.1 shows the complete structure of COM624P's Main Menu and its successive

pull-down menus.

The main function of the File Menu is for assigning files for

input, output, and graphical data. The "Input" Menu will call up Module C624EDIT which consists of four sub-menus. The sub-menu named "Analysis" in C624EDIT is for entering data that are needed

for computation of a pile under lateral loading. The sub-menu named "MuIt" is for entering data that are needed for computing

the ultimate bending moment and EI-values for the selected-pile

section. Because Module C624EDIT also can be used as a stand- alone program, the "File" sub-menu is provided for reading and

saving of the data files. The "Option" sub-menu mainly provides

the user an easy way for changing parameters on configuration.

The "Run" Menu will call up Module COM624P for execution,

using the specified files for input and output. The "Graphics"

Menu will call up Module C624VIEW, which consists of four sub-

menus. The sub-menu "File" under the Graphics Menu is needed only

if the Module C624VIEW is used as a stand-alone program. If a

file name for graphical data has been given earlier, the program

will automatically use that file for producing graphical results.

The sub-menu named "View" is for generating graphics on the screen

for preview. The sub-menu named "Plot" is for generating HP-GL

plotting files for high-quality pen plotters. The sub-menu

"Option" is provided for changing the parameters on configuration.

The detailed discussion of each menu will be presented later in

this chapter.

21

I F ile Input RU7 Graphics I

Input File output file Graphics file Changer Dir. Quit to DOS Main Menu

Option I

Read New Save Write Directory

ZiiZ%Z Main Mew

pile Properties soil PropertIes Lateral py Duta

=sZd3 Output Tables Main Menu

Cross-Section Axial Loads Strength of Mai Dimension r?t3t?t3tM~~g*

File V&W Plot Option

I I I

I I PY curves Response Curve! Ultimate Moment Interaction Dia. viewculves Main Menu

Ultimate Moment Interaction Dia. viewculves Main Menu

I

py c;urves Response Curves Ultimate Moment Interaction Dia.

Ei$Z

Figure 3.1. Main menu structure of COM624P.

22

GUIDE FOR USING MAINMENU

The MAINMENU.BAT file is a special batch file that will

integrate all the modules needed for operation of COM624P in the

DOS environment. The shell process was used so that the computer

will automatically transfer control to the appropriate module,

based on the given command.

To initiate the program, the user enters

C:\COM624P>MAINMENU <CR>

The program will quickly bring up the Main Menu on the Screen.

The Main Menu has four choices: File, Input, Run, and Graphics.

File Input Run Graphics

This program is developed especially for Design and analysis of piles under lateral loading. The current version is 2.0

The selection of the FILE menu allows the user to access a pull- down menu for file operations such as assigning input file, output file, and graphics file, reading in an existing file, creating a new data file, checking files in the directory, and similar operations.

The selection of INPUT menu allows the user to access Program C624EDIT to create a data file or to edit an existing data file.

The selection of the RUN menu allows the user to execute the program with the specified input and output files.

The selection of the GRAPHICS menu allows the user to view the soil and pile response curves directly on the screen. The system must have graphics adapters such as CGA, EGA, VGA, or monographics adapter in order to view the graphics.

Fl-Help Alt-X-Exit

Once the Main Menu has been called, an item can be selected

by pressing the key corresponding to the first letter in the name

of the menu. The arrow keys can also be used to move the

highlight bar and Enter can be pressed when the bar is at the

appropriate command.

23

The selection of the File Menu allows the user to access a

pull-down menu for file operations such as assigning an input

file, output file, and graphics file, reading an existing file, creating a new data file, checking files in the directory, and similar operations.

The selection of the Input Menu changes the screen from the

Main Menu to the Input Menu as shown in Figure 3.1. The selection of the Run Menu allows the user to execute the program with the

specified files for input and output. The selection of the Graphics Menu changes the screen from the Main Menu to the

Graphics Menu as shown in Fig. 3.1.

The first step is to select the File Menu. Once the File Menu has been pulled down, the hot keys for the Up arrow and the Down arrow can be used to highlight the desired command.

File Input Run Graphics

Graphic File

Fl-Help Alt-X-Exit

24

The user needs to specify a Input, Output, and Graphics file

before selecting the Input, Run or Graphics Menu. File Input Run Graphics

Read File Name EXAMPLE.INl

I

Fl-Help Alt-X-Exit

GUIDE FOR USING INPUT MENU

Once you select the "INPUT** from the Main Menu, the Input

Menu will be shown on the screen as in the following. File Analysis Mult Option

C624EDIT 2.0, Edit Variables:

This program is a preprocessor developed especially for users for preparation of input for the computer program COM624P. The main menu for this program is displayed as a bar at the top row of the screen. The main menu has four choices: FILE, ANALYSIS, MULT, and OPTION.

The selection of the FILE menu allows the user to access a pull- down menu for file operations such as reading in an existing file, creating a new data file, checking files in the directory, and similar operations. The selection of the ANALYSIS menu allows the user to enter required data for computing the response of the pile and soil, such as distributions of deflection, bending moment, shear, and soil resistance as a function of length along the pile. The selection of the MULT menu allows the user to enter data of a selected pile size for computing the ultimate bending moment and other design-related information. The OPTION menu is used for screen setting and it may not be needed for most computer systems.

Fl-Help Alt-X-Exit 25

The Input Menu has four submenus: File, Analysis, MULT, and

Option. The four menus allow the user to access file operations,

data editing, control of variables in the analysis, and program

options. If help is needed for data entry, the FI key is pressed

to access the help files.

The user can move from one choice to another by using either

the arrow keys or by typing the highlighted letter of the choice.

Thus, if the File selection is currently highlighted (and the File

pull-down menu is not shown), one may move to the Analysis

selection by either typing the right-arrow key twice or by typing

'A' or 'at for Analysis.

The File Submenu presented under the "Input" menu provides

additional access to the commands for the control of input files.

This menu controls reading of input files, creation of new input

files, saving of files, examining the contents of any subdirectory, changing of directories, and exiting the program at

the conclusion of use.

If the user has already specified the file name for the input

data under the Main Menu, they need not give the file name here;

however, if the input file was not specified previously, the

selection of llFile" will allow you to enter the file name again.

To access the file menu, you need to move the highlighted bar to

the "File" and press <Enter>. The options under the File submenu

will be shown on the screen as the following.

The File pull-down menu commands are:

Read - to read data files, New - to create a new data file, Save - to save the current data as a disk file,

26

Directory - to display disk directories, Change Dir - to switch subdirectories, Exit to DOS - to leave the program, and Main - to return to the Main Menu.

File Analysis

Read New Save

-n

Directory Change dir Quit to DOS Main Menu

Mult Option

Fl-Help Alt-X-Exit

For example, to retrieve an existing input file named EXAMPLE.IN6,

you can move the cursor to highlight "Read" on the submenu and

press <Enter>. The screen will have a window for the user to

enter the file name as shown below.

File Analyaio m1t option

New File Nanw New File Nanw EXAMPLE.INb EXAMPLE.INb

I I

Fl-Help Alt-X-Exit 27

Once the input file is found, the program will read line by line

from the file and the data will be echoed on the screen.

File Analysis Mult Option Reading EXAMPLE.IN6

Line #lo: 30.0000 30.0000 14906.0000 707.0000 Line X10: 160.0000 30.0000 47813.0000 707.0000 Line X11: 1 4 0.0000 360.0000 90.0000 Line #12: 0.0000 0.06900 Line #12: 360.0000 0.06900 Line #13: 0.0000 0.0000 38.0000 0.00000 Line #13: 360.0000 0.0000 38.0000 0.00000 Line #17: Line #18: 2~.0000 Line X18: 60.0000 Line #18: 100.0000 Line #18: 150.0000 Line #19: 1 Line #20: 1 60000.0000 0.0000 50000.0000 Line X21: Line #22: 5o;oo.o~ Line #23: 3500.00 60000.00 0.00 29000000.00 Line #24: 0.00 30.00 0.00 0.00 0.00 Line #25: 8 12 0 3.0000 Press any key to continue . . . . .

Fl-Help Alt-X-Exit

If there is an error in retrieving data, a message will be given

on the screen, The user should note the cause of the error and

press the <Enter> key to continue. Most of the errors have to do

with the format of input' data. The user should check the line

number and make the correction later on the Edit screen.

After the editing of the input data is completed, the user

needs to save the new data by moving the cursor to "Save" and

pressing <Enter> after the "Save" was highlighted. A window will

allow the user to give a file name for the new data as shown in

the following.

The user can press "M" and then <Enter> to return to the initial

Input Menu.

28

File Analysis Mult Option

Read 1 New Save

Save File Name EXAMPLE.IN7

!ain Menu I

]

Fl-Help Alt-X-Exit

The Analysis Submenu opens access to edit the various data

groups defining the problem. Variables that may be edited through

this submenu are title for the problem, pile properties, soil

properties, load-transfer data, data for loading, computation

control and output format.


Title Pile Properties Soil Properties Lateral p-y Data Data for Loading Computation Control Output Tables Main Menu

Fl-Help Alt-X-Exit

29

The Analysis pull-down menu commands are:

Title - to edit the program title, Pile Properties - to edit the pile properties (length,

diameter, cross-sectional area, and EI), Soil Properties - to edit the soil properties (layers,

strength parameters, unit weights, etc.), Load-Transfer - to edit the user-specified p-y curves, Data for Loading - to edit loads at the top of the pile and

the distributed load, Computation Control - to select the tolerance and iteration

numbers for computation, Output Tables - to select options for printing output data,

and Main - to return to Main Menu.

The user can select any one of the items shown in the

Analysis submenu to review, create, or change the data. Some of

the variables for input may use an abbreviated name because of the

limited space available on the editing window. However, all

variables will have a full, detailed explanation in the help file.

It should also be noted that all the x-coordinates described by

the program are based on the origin which is set at the top of the

pile. If help is needed for data entry, the user can press the

"Fl" key to access the help file, and press the "FS" to return to

the edit screen.

The screens that are used to create data for EXAMPLE.IN6 are

presented in the following to illustrate the usage of the Analysis

submenu.

30



This program is a preprocessor developed especially for users for preparation of input for the computer program coM624P. The main menu for this Program is displayed as a bar at the top row of the screen. The main menu has four choices: FILE, ANALYSIS, MULT, and OPTION.


I I Fl-Help Alt-X-Exit


Title -- Pile Properties Soil Properties Lateral p-y Data Data for Loading Computation Control Output Tables Main Menu

Fl-Help Alt-X-Exit

Move the cursor to "Title", then press <Enter> key; the following screen will appear.

31

File Analysis Mult Option EXAMPLE.IN6

Enter title for this data file (up to 72 characters long)

EXAMPLE 6 ANALYSES RELATED TO DESIGN OF CONCRETE PILES

A 1:DEF:Lab EXAMPLE 6 ANALYSES RELATED TO DESIGN OF CONCRETE PILES L : Move Cell - ? : Help - / : Edit Screen----- F8 : Continue - Fl-Help Alt-X-Exit

Press Command Key: [FBI l

File .C

/

1

Analysis Mult

Title Pile Properties- Soil Properties Lateral p-y Data Data for Loading Computation Control Output Tables Main Menu

Option

Fl-Help Alt-X-Exit

Move the cursor to "Pile Properties*', then press <Enter> key; the following screen will appear.

32


Editing Pile Dimensions

Number of increments (<= 300) ..................... 100 Distance from top of pile to ground surface - inches 0.0 Length of pile .............................. inches 360.00 Pile modulus ................................ psi 3200000 Slope of ground surface (degrees) ................. 0.0000

A 1:DEF:Num L 100

: Move Cell - Fl-Help Alt-X-Exit?

: Help - / : Edit Screen--- F8 : Continue -

Press Command Key: [F81.


Editing Pile Section Properties

Section Top Depth Diameter Mom. of Inert. Area

f inches inches inches**4 inches'

0.00 30.000 47813.0000 707.0000 2 30.00 30.000 14906.0000 707.0000 3 160.00 30.000 47813.0000 707.0000 4

ii 7 8 9

10

To access pile property library leave pile diameter blank.

A 1:DEF:Num 0.00000 L l Move Cell - Fl-Help'

? : Help - / : Edit Screen- F8 : Continue 1 Alt-X-Exit

Press Command Key [Fl] or "?" for help, the screen on next page will appear.

33

File Analysis Mult Option I I

Help Topics

Mult MENU Edit - Mult - Shape and Axial Loads

Computation Control Edit -

Mult - Mult -

&bar & Concrete Strength FILE MENU Output Tables

Section Dimension File - Read Mult - Rebar Arrangement File - New

EDIT MENU File - Save Edit - Title File - Write Edit - Pile Properties- File - Edit - Soil Properties

Directory File -

Edit - Soil - p-y Criteria Change Directory

File - Exit to DOS Edit - Soil - Edit

k for Clays MAIN MENU - Soil - k for Sands Main - Pull-down Menus

Edit - Soil - E50 Main - Edit - Soil -

Hot Keys OPTIONS MENU

Edit p-y Multipliers

- Soil - Unit Weights Edit

Options - Units - Lat. Load Trans.

Edit - Data for Loading ~',~::: - Pile Property Library - Save Config. File

Options - Auto-backup

Fl-Help Alt-X-Exit

Move the cursor to "Pile Properties" and press <Enter>; the following screen will appear.

File Analysis Mult Option *

The maximum number of increments allowed into which the pile is divided is 300. Typically the user will have selected the number of increments to be equal to some multiple of the overall pile length, so that the output values are calculated uniformly with depth.

Piles can have several different segments but each one is treated as a uniform cross section. For taper piles, the program allows the user to use up to 10 uniform segments to model the properties. "Top Depth" shown in Editing Pile Section Properties is the x-coord. (depth below the top of pile) of the top of a segment of pile with uniform cross section.

For frequent designers if the pile diameter is set equal to zero, the user gains access to a library file defining pile properties. L The pile property library is created separately by the user for his own use.

--I

If the units of the data in the pile property library are different from those set inside C624EDIT, a units conversion is performed

Fl : Help Index - PageUp PageDown - F8 : Return Fl-Help Alt-X-Exit

Press Command Key [F8] to return to the Edit Menu.

34



Section Top Depth Diameter Mom. Of Inert. Area

: inches inches inches**4 inches'

0.00 30.000 47813.0000 707.0000 2 30.00 30.000 14906.0000 707.0000 i 160.00 30.000 47813.0000 707.0000

: 7 8

1x


A 1:DEF:Num 0.00000 L : Move Cell - ? : Help - / : Edit Screen F8 : Continue 2 Fl-Help Alt-X-Exit

Press Command Key: fF81.

File Analysis Mult

Title Pile Properties Soil Properties4 Lateral p-y Data Data for Loading Computation Control Output Tables Main Menu

J

Option

Fl-Help Alt-X-Exit

Move the cursor to "Soil Properties", then press <Enter>; the following screen will appear.

35

File Analysis Mult Option EXAMFLE.IN6

Editing Soil Layer Information

Layer Criteria x-top X-bot k

r # inches inches lb/in3

0.00 360.00 90.00 2 i 360.00 540.00 500.00

: 5

4

i 10

p-y Curve Criteria = Soft Clay Criteria #3 =

Stiff clay Below Watertable Stiff Clay Above Watertable

= Sand = Interp. Between Input Curves :t = Vuggy Limestone

D 2:DEF:Num 500.00000 L : Move Cell - 3 : Help - / : Edit Screen- F8 : Continue - Fl-Help Alt-X-Exit

Press Command Key [F8] to continue.

File Analysis Mult Option FJ@MF'LE.IN6

Editing Effective Unit Weight Information

Point

r 2

:

z 7

i 10

Depth inches

0.00 360.00

360.00 540.00

Unit Weight lb/in3

0.069 0.069

0.034 0.034

A 4:DEF:Num 540.00000 L : Move Cell - ? : Help - / : Edit Screen- F8 : Continue - Fl-Help Alt-X-Exit


36


Editing Shear Strength Information

Layer Depth C n inches

ES0 psi de:. @ 50% of c

5 360.00 0.00 0.000 38.00 0.0000 0.000

3 38.00

360.00 0.0000

10.000 0.00 4 540.00

0.0050 10.000 0.00

5 0.0050

t

A 4:DEF:Num 540.00000

: Move Cell - ? : Help - / : Edit Screen- F8 : Continue - Fl-Help Alt-X-Exit

Press Command Key EF8l.

File Analysis Mult option

Title ,Pile Properties Soil Properties Lateral p-y Data Data for Loading Computation Control Output Tables Main Menu t

Fl-Help Alt-X-Exit

Move the cursor to "Data for Loading", then press <Enter>; the following screen will appear.

37


Editing Loading Information

Distributed lateral loading (y/n) 7 ............... n Is loading cyclic (y/n) ? ......................... n Boundary condition code (KBC) ..................... 1

KBC = 1 for shear and moment (free head) KBC = 2 for shear and slope (fixed head)

EE = 3 for shear and rotational restraint (partially fixed) = 4 for deflection and moment

A l:DEF:Lab n L : Move Cell - ? : Help - / : Edit Screen- F8 : Continue 1 Fl-Help Alt-X-Exit



Editing Pile-head Loading

KOP Shear Moment Axial Load pounds in-lbs pounds

1 20000.00 0.000 50000.00 1 40000.00 0.000 50000.00

KOP=O if only a summary output for this load to be printed =l if complete output is desired for this load

A ~:DEF:NuIII 1 L : Move Cell - ? : Help - / : Edit Scree v F8 : Continue - Fl-Help Alt-X-Exit

Press Command Key [F8],

38

File Analysis

r Mult Option

Title Pile Properties Soil Properties Lateral p-y Data Data for Loading Computation Control-ti Output Tables Main Menu

1. Maximum number of iterations allowed for analysis : 100 2. Tolerance on solution convergence, inches : 0.000010 3. Value of deflection considered to be excessive, inches : 147.0000 4. Computation using internally-generated cracked EI (Y/N : N Note: If the above answer is Y, remeber to enter the same

axial load and other parameters such as arrangement of rebar, concrete and rebar strength in the WJLT" menu later.

Fl-Help Alt-X-Exit

Move the cursor to "Computation Control", then press <Enter>; the following screen will appear.

File Analysis Mult Option EXAMPLE.IN6 I

I A 1:DEF:Num 100 J l- : Move Cell - ? : Help - / : Edit Screen- F8 : Continue -

Fl-Help Alt-X-Exit

Press Command Key [F8] (if needed, press the [F-l] key to access the Help File for an explanation of cracked/untracked EI) l

39

File Analysis Mult

Title Pile Properties Soil Properties Lateral p-y Data Data for Loading Computation Control Output Tables- Main Menu

Option

Fl-Help Alt-X-Exit

Move the cursor to "Output Tables," then press <Enter>; the following screen will appear.


Output Printing Options

I *** Lateral Load Analysis ***

Printing Increment (1 for every node, 2 for every other node, etc) 1 Print deflection, moment, shear over full length of pile (y/n) Y Print p-y curves for verification Y

A 1:DEF:Num 1 L : Move Cell - ? : Help - / : Edit Screen- F8 : Continue - Fl-Help Alt-X-Exit

Press Command Key: LF81.

The MULT Submenu opens access to the editing commands for

ultimate-bending moment computation. Variables edited through

this menu are the title for computation, cross-sectional shape,

axial loads, strength of materials, dimensions of cross section,

and rebar measurement. The user can pull down the MULT submenu by

moving the highlighted bar to "MULTW and press <Enter> after the

initial Input Menu is returned to the screen as shown below.


Title Cross Section Shipe Axial Loads . Strength of Materials Dimension of Cross SeCtiOn Rebar Arrangement Main Menu

Fl-Help Alt-X-Exit

The MULT pull-down menu commands are:

Title - to edit the program title, Cross-section Shape - to select the shape of the cross section, Axial Loads - to enter the values of axial loads that are

considered, Strength of Materials - to enter the yield strength and the

elastic modulus, Dimension of Cross Section - to enter the dimensions for

specified cross section, Rebar Arrangement - to enter the rebar size, rebar number and

arrangement, and Main - to return to Main Menu.

41

If the user would like to compute the ultimate bending moment

of the pile or ask the program to generate cracked/untracked

bending stiffness used for deflection computation, input data

should be provided for each item under the MULT submenu. If

cracked EI is chosen for the computation, the axial load entered

in the "Data for Loading" submenu of the "Analysis" menu should be

consistent with the axial load used in the "MultV1 submenu for each

case. If help is needed for data entry, the user can press "Fl"

key to access the help file and then press the "F8" key to return

to the previous screen.

The screens that are needed to create data for EXAMPLE.ING

are presented in the following screens to illustrate the usage of

the MULT menu.


Title Cross Section Shaped Axial Loads Strength of Materials Dimension of Cross Section Rebar Arrangement Main Menu

Fl-Help Alt-X-Exit Press Command Key: [Cl *

42


Identification number of the shape of cross section of the pile:

1: Rectangular or square; 2: Circular (without shell or core); 3: Circular (with shell but without core); 4: Circular (with shell and core); 5: Circular steel pipe;

Enter the number: 2

A l:DEF:Num L 2

: Move Cell - ? : Help - / : Edit Screen- FE : Continue - Fl-Help Alt-X-Exit

Press Command Key: [F81


Title Cross Section Shape Axial Loads- Strength of Materials Dimension of Cross Sectiol Rebar Arrangement Main Menu

EXAMPLE.IN6

Fl-Help Alt-X-Exit

press Command Key: [Al

43

Analysis Option EXAMPLE.IN6

Enter axial loads for cross section design:

Point Loads pounds

1 2

50000.00

If the cracked EI will be used in computation of the pile deflection, the field will show the same axial load given in the "Analysis" menu.

A 1:DEF:Num 50000.00000

: Move Cell - ? : Help - / : Edit Screen- F8 : Continue - Fl-Help Alt-X-Exit

Press Commar,d Key:

File Analysis

IF81

Mult Option EXAMPLE.IN6

Dimension of Cross Section Rebar Arrangement Main Menu

Fl-Help Alt-X-Exit

rress Command Key: Sl

44


I Enter strength parameters of materials ---------_----------------------------

Cylinder strength of concrete psi 3500.00000 Yield strength of reinforcement psi 60000.00000 yield strength of shell or core psi 0.00000 Modulus of elasticity of steel psi 29000000.00000

A ~:DEF:NuIII 3500.00000000 L : Move Cell - ? : Help - / : Edit Screen- F8 : Continue - Fl-Help Alt-X-Exit

Press Command Key: [F~I


Title Cross Section Shape Axial Loads * Strength of Materials Dimension of Cross Section Rebar Arrangement Main Menu

l J 1 RXAMPLE.IN6

Fl-Help Alt-X-Exit

Press Command Key: [Dl

45

File Analysis Mult Option EXAMPLE.INC

Enter cross-section dimension --------------_----_---------

Width of section (rectangular section only) inches 0.00000 Depth of section (rectangular section only) inches 0.00000 outer diameter (circular section only) inches 30.00000 Outer diameter of core (circular section only) inches 0.00000 Thickness of shell (circular section only) inches 0.00000 Thickness of core (circular section only) inches 0.00000

A 1:DEF:Num 0.00000000

: Move Cell - 3 : Help - I : Edit Screen- F8 : Continue 1 Fl-Help Alt-X-Exit

Press Command Key:

File Analysis

[F81

Mult Option EXAMPLE.IN6

Title Cross Section Shape Axial Loads * Strength of Materials Dimension of Cross Section Rebar Arrangement Main Menu

Fl-Help Alt-X-Exit

r.r e = .s command Key: LRJ

46


Rebar Arrangement

Size of the rebar (enter the bar number, 3, 5, 8, 9...) 8 Number of reinforcing bars 12 Number of rows of reinforcing bars (rectangular section only) 0 Cover of rebar (from center of rebar to outer edge 3.0000 of concrete) inches

A 1:DEF:Num 8 L : Move Cell - ? : Help - / : Edit Screen- F8 : Continue 1 Fl-Help Alt-X-Exit

Press Command Key: I~83


Title Cross Section Shape Axial Loads Strength of Materials Dimension of Cross SeCtiOn Rebar Arrangement Main Menu-

Fl-Help Alt-X-Exit

Press Command Key: [Ml

47

File Analysis Mult


Option

This program is a preprocessor developed especially for users for preparation of input for the computer program COM624P. main menu for this program is displayed as a bar at the top

The

row of the screen. The main menu has four choices: FILE, ANALYSIS, MULT, and OPTION.

The selection of the FILE menu allows the user to access a pull- down menu for file operations such as reading in an existing file, creating a new data file, checking files in the directory, and similar operations. The selection of the ANALYSIS menu allows the user to enter reguired data for computing the response of the pile and soil, such as distributions of deflection, bending moment, shear, and soil resistance as a function of length along the pile. The selection of the MULT menu allows the user to enter data of a selected pile size for computing the ultimate bending moment and other design-related information. The OPTION menu is used for screen setting and it may not be needed for most computer systems.

I Fl-Help Alt-X-Exit

Press Command Key: IF1


Fl-Help Alt-X-Exit

Press Command Key: [Sl

48

The Options Submenu provides a path for the user to the commands that control where C624EDIT looks for a library file, for

pile properties, and to save the current Analysis variables in the

configuration file. The procedure for accessing the Options pull-

down menu is no different than for the other menus. The user can move the cursor to "Options" and press <Enter>. The following

information will be shown on your screen.


?igggzq

Fl-Help Alt-X-Exit

The Options pull-down menu commands are:

Units - to select units for computation, Library Directory - to change the name of the subdirectory

containing the pile-properties library, Save Configuration File - to save the current values of the

Analysis and Options variables to the configuration file,

Auto Backup - a toggle switch to enable the automatic backing up of any file read by C624EDIT.EXE, so that the file may be saved under its original name. The backup-file name will be the original file name with a file extension of 'lBAK,ll and

Main - to return to the Main Menu.

49

COM624P can perform calculations in pounds and inches (Option l),

kilonewtons and meters (Option 2), or any consistent set on units

(Option 3) for force and length. The user should take care that all input values are entered in consistent units. The following screen will illustrate how to select the units that the user

requires.


Fl-Help Alt-X-Exit

In many cases, a user may want to try several different sizes

of piles, which can be a standard steel section or a non-standard

reinforced concrete section, for the preliminary studies. The

pile-library file is a data-base file in which the user can store

data for most commonly-used pile sections. This file will be

automatically loaded into the computer memory each time the user

calls the Input Menu.

The pile-library file is associated with the section for

editing pile properties in Module C624EDIT. The pile-library data

will be presented on the screen for selection if the user leaves

50

blank the entry fields for pile diameter, moment of inertia, and

area during the editing process.

The name of the file under which,C624EDIT looks for the pile

property library can have up to 42 characters. The user should be

sure to enter the full name of the pile property library file,

including the disk drive letter and path. The following screens

will illustrate how to select the new pile property library.

51

File Ana1ySi.S Mult Option

Editing Pile Section Properties I



0.00 2 240.00

:

2 7 8 9

10


A 2:DEF:Num 240.00000

: Move Cell - ? : Help - / : Edit Screen- F8 : Continue I 4 Fl-Help Alt-X-Exit

Leave blank for all fields except for "Top Depth", then press [F81 key.


Pile Section 1 - Top Depth = 0.00 inches

Select Appropriate Pile Type

HP 14x117, Axis x-x HP 14x117 Axis Y-Y HP 14x102, Axis X-X- HP 14x102, Axis Y-Y HP 14x89, Axis X-X HP 14x89, Axis Y-Y HP 14x73, Axis X-X HP 14x73, Axis Y-Y HP 12x74, Axis x-x HP 12x74, Axis Y-Y

FX=A FY=3 Page = 0 Library entry 3

I

Fl-Help Alt-X-Exit

Move the cursor to the selection for the first pile segment, then press <Enter>.

52


Pile Section 2 - Top Depth = 240.00 inches

Select Appropriate Pile Type

HP 14x117, Axis X-X HP 14x117 Axis Y-Y HP 14x102, Axis X-X HP 14x102, Axis Y-Y HP 14x89, Axis x-x HP 14x89, Axis Y-Y HP 14x73, Axis X-X- HP 14x73, Axis Y-Y HP 12x74, Axis X-X HP 12x74, Axis Y-Y

FX=A FY=7 Page = 0 Library entry 7

Fl-Help Alt-X-Exit

Move the cursor to the selection for the second segment, then press <Enter>.



Section

! 2 3

Top Depth Diameter Mom. of Inert. Area inches inches inches**4 inches'

0.00 14.030 1050.0000 30.0000 240.00 13.640 734.0000 21.5000

4 5

7" 8 9

10


A 1:DEF:Num 0.00000 L : Move Cell - 3 : Help - / : Edit Scrcen- F8 : Continue I Fl-Help Alt-X-Exit

The selection from the pile-library is shown on the above screen.

53

The format for pile-library data is quite straightforward.

There are two lines of input reserved for each size of pile. The

first line is used for the description of the pile section such as

"HP 14 x 73, Y-Y Axis". The second line consists of five entry

fields. The first entry is the I.D. for units. For English Units

"1" is entered, and "2" is entered for S.I. units. The second

entry on Line 2 is the diameter or width of the section

perpendicular to the direction of loading. The third entry on

Line 2 is the value of the moment of inertia. The fourth entry on

Line 2 is the cross-sectional area. The last entry is the modulus

of elasticity for the section. The free-field format is used for

the entry. The user can use any text editor to add or delete the

data in the pile-library file.

When a selection is made from the Analysis or Mult Submenus,

a data-entry-worksheet display appears on the screen. The data

that have been entered are shown in a spreadsheet-type

arrangement.

The data-entry worksheet screen, as shown in Fig. 3.2,

contains three main sections:

1. The top line of the screen display is the Main Menu with 'Edit' highlighted.

2. The data-entry worksheet section consists of two boxes, a large box about 18 lines high followed by a small box about two lines high.

3. The bottom two lines of the display contain a guide to some of the 'key assignments' for commands to use with the data-entry worksheet.

54

WI ul

File Analysis Mult option EXAMPLE.IN6 -Top Line


Layer Depth ES0 # inches PST de:. e 50% 0f c

2’ 360.00 0.00 0.000 0.000 38.00 38.00 0.0000 0.0000

:

: 7

i 10

A 1:DEF:Num 0.00000

: Move Cell - ? : Help - / : Edit Screen---- F8 : Continue - Fl-Help Alt-X-Exit

-Large box for data entry

Small box for -data entry

-Key Assignment

Figure 3.2. Data-entry worksheet.

The data-entry worksheet, Section 2, is the most important

part of the display, and the section where all of the data-entry

operations will take place.

The upper, and largest, box of the worksheet section of the

screen display contains the data that have been entered. These

data are in a spreadsheet-type arrangement; that is, in columns, designated alphabetically from left to right, and in rowsl

designated numerically from top to bottom. A location, designated

by a column letter and a row number, is called a cell and each

item of data is stored in one of these cells. By using the

cursor-movement commands, a highlight can be moved in any

direction from the upper left cell to the lower right cell. The

highlighted cell is called the 'working cell'. A cell must be

highlighted - the working cell - for data to be entered or edited. The data in an existing file, shown on the worksheet, can be

manipulated to some extent by using the Worksheet Edit commands

that will be described later.

The lower box of the worksheet section of the display is

where data are entered into the working cell, or the existing data

is edited. This box has two lines. The upper line shows the

following information for the working cell:

Location - column letter and row number, Status - UND means the cell is not defined as a part of

the data and DEF means the cell has been defined to contain data, and

Data - the data type [Num for numeric and Lab(labe1) for alphanumeric] followed by the existing data in the cell.

The bottom line of the lower box is the 'Entry Line' where

data entry or data editing are done. A blinking cursor is shown

on this line. Data are typed by moving the cursor to the right.

Only the Backspace key, however, may be used for corrections to

56

the typed data; the Backspace key is used to move the cursor back

(without canceling the typed symbols) to where a correction is to

be made, and then the correct data are overtyped. The Enter (Return) key is used to accept edited data as the data in the

working cell.

If the information in the working cell requires editing, two

methods may be used. The simplest way is merely to reenter the

data. The other way is to enter the Cell Edit Mode by pressing

the F2 key. Editing in this mode will be explained later. The

key assignments in the bottom two lines of the display, Section 3,

change to show Cell Edit commands. These commands are used to

make the desired modifications to the data in a cell. Pressing

Enter (Return) will exit the Edit Mode and also replace the

existing data in the working cell with the edited data.

There are three sets of commands to be used with a data-entry

worksheet. These are the Basic Worksheet Commands, the Cell Edit

Commands, and the Worksheet Edit Commands. The Basic Worksheet

Commands are in effect when a data-entry worksheet is entered.

The other two sets of commands are invoked from the Basic

Worksheet Commands. A key assignment in the form of '"(key)' may

be found in the command sets. To obtain this key assignment, the

'Cntl' and the second key are pressed at the same time. For

example, ^A is obtained by pressing <Cntl> and <A> at the same

time. The key assignments for the various sets of commands are

given in the following paragraphs.

These commands are in effect when a display of a data-entry

worksheet is on the screen, except when either of the other two

57

command sets has been invoked and is in use. The key assignments

for some, but not all, of these commands are shown in the bottom

two lines, Section 3, of the screen display. The key assignments

for the commands in this set are as follows:

Left Arrow Move highlight one cell to the left

Right Arrow Move highlight one cell to the right

Up Arrow Move highlight up one cell

Down Arrow Move highlight down one cell

Page Up Move up one page (if more than one page)

Page Down Move down one page (if more than one page)

F2

Return (Enter)

Enter Cell-Edit Mode

Accept data entered or edited, exit Cell- Edit Mode

/

FB

Enter Worksheet-Edit Mode

Return to Edit Menu or move to next worksheet for current menu item

End

? or Fl

Return to Main Menu

Enter Help Mode

The preceding commands are all self-explanatory except for “F2 II - Enter Cell - Edit Mode and V/I1 - Enter Worksheet - Edit

Mode, which will be described in detail in the next two sections.

58

The following screens illustrate the procedures for calling

the help file during data entry. It should be noted that the help

file is a simple text file to which the user can add his/her own

comments or notes at desirable locations. The user can open the

help file named C624EDID.HLP by using any available text editor.

The help file, however, always needs to stay in the same file

directory with C624EDIT.EXE.

File Analysis Mult Option E2CAMPLE.IN6


Layer Depth # inches p*: de;. *

ES0 e 50% of c

1 0.00 0.000 38.00 0.0000 I: 360.00 0.000 38.00 0.0000

4

z 7 8 9

10

4. 1:DEF:Num 0.00000

: Move Cell - 3 : Help - / : Edit Screen F8 : Continue + Fl-Help Alt-X-Exit

The help topics will be shown on the screen once the "Fl" or

"?I' keys have been pressed. You can move the cursor to the

desired topics and press <Enter> to bring the help instruction on

to the screen.

59


Help Topics

Mult MENU Mult - Shape and Axial Loads Mult - Mult -

Rebar & Concrete Strength Section Dimension

Mult - Rebar Arrangement EDIT MRNU

Edit - Title Edit - Pile Properties Edit - Soil Properties Edit - Soil - Edit

p-y Criteria - Soil -

Edit k for Clays

- Soil - k for Sands Edit - Soil - ESO- Edit - Soil - Edit

p-y Multipliers - Soil -

Edit - Unit Weights

Lat. Load Trans. Edit - Data for Loading

Edit - Computation Control Edit - Output Tables

FILE MRNU File - Read File - New File - Save File - Write File - Directory File - Change Directory File - Exit to DOS

MAIN MENU Main - Pull-down Menus Main - Hot Keys

OPTIONS MENU Options - Units Options - Pile Property Library Options - Save Config. File Options - Auto-backup

Fl-Help Alt-X-Exit

Move the cursor to the "E50", then press <Enter>.


Soil Strain Parameter ES0

Soft Clay, c = 1.74 to 3.47 psi 250 to 500 psf

12 to 24 KPa

Medium Clay, c = 3.47 to 6.94 psi 500 to 1000 psf

24 to 48 KPa

Stiff Clay, c = 6.94 to 13.9 psi 1000 to 2000 psf

48 to 96 KPa

Very Stiff Clay, c = 13.9 to 27.8 psi 2000 to 4000 psf

96 to 192 KPa

ES0 = 0.02

ES0 = 0.01

ES0 = 0.007

ES0 = 0.005

- Fl : Help Index - Fl-Help

PageUp PageDown - F8 Alt-X-Exit

: Return -

Press Command Key [F8] to return.

60

The Cell-Edit Mode is used to make changes and additions to

the data in the working cell, and is entered by typing the F2 key.

When this key is pressed, a highlighted bar will appear on the

line between the two worksheet boxes as shown in the following.




Edit Mode Overwrite R l:DEF:Lab EXAMPLE 6 ANALYSES RELATED TO DESIGN OF CONCRETE PILES EXAMPLE 6 #;LY$ES RELATED TO DESIGN OF CONCRETE PILES

F : Move Cursor Insert/Delete/-G A Fl-Help Alt-X-Exit

The highlighted bar contains 'Edit Mode' and an indication that

the data entry is in the 'Insert' or the 'Overwrite' condition.

Two general types of commands are available, cursor-movement

commands and data-change commands. The key assignments for the

Cell-Edit Mode are displayed in the bottom two lines, Section 3,

of the screen.

Left Arrow Move cursor on the entry line to the left

61

Right Arrow

"A

Move cursor on the entry line to the right

Move cursor to beginning of the entry line

^F Move cursor to end of the entry line

Insert Toggles between 'Insert' and 'Overtype' for data entry

Del Deletes character to the left of the cursor

^G Deletes character at the cursor

Return (Enter) Accepts data on the entry line and exits Cell-Edit Mode

The following screens illustrate how to use the above

commands for changing the data.




Edit Mode Insert On b 1:DEF:Lab EXAMPLE 6 ANALYSES RELATED TO DESIGN OF CONCRETE PILES XAMPLE 6 ANU$Y$ES RELATED TO DESIGN OF REINFORCED CONC- PILES

F : Move Cursor Insert/Delete/ G - Fl-Help Alt-X-Exit

Press the rrIns81 key to change to insert mode for the edited cell,

then add the word "Reinforced" before the word "Concrete" as shown

in the next screen.

62

File Analysis Mult optiori EXAMPLE.IN6

Enter title for this data file (UP to 72 characters long)

EXAMPLE 6 ANALYSES RELATED TO DESIGN OF REINFORCED CONCRETE PILES

A 1:DEF:Lab EXAMPLE 6 ANALYSES RELATED TO DESIGN OF REINFORCED CONCRETE PILES

: Move Cell - 7 : Help - / : Edit Screen- F8 : Continue " Fl-Help Alt-X-Exit

The Worksheet-Edit Mode is used to manipulate entire lines of

data in the worksheet. It is invoked by typing I/' from the

Basic-Worksheet-Command list. When the I/' is typed, a highlighted bar appears on the line between the two worksheet

boxes, and a list of possible operations appears in the

highlighted bar as shown in the following.





0.00 30.000 47813.0000 707.0000 2 30.00 30.000 14906.0000 707.0000 3 160.00 30.000 47813.0000 707.0000

ii 6 7

10


Blank Copy Delete Exchange Insert Move A 1:DEF:Num 0.00000

z Move Cell - 3 t Help - / : Edit Screen- F8 : Continue --L--- Fl-Help Alt-X-Exit

63

A I/' also appears on the entry line of the lower box. To

complete the command, the first letter of the choice from the list

of possible operations is typed on the entry line; in addition,

some answers to prompts on the entry line may have to be typed.

After the selected operation is complete, the program returns to

the Basic-Worksheet-Command Mode. The following operations are

available:

/B(lank)

/C(opy)

/D(elete)

/E(xchange)

/I(nsert)

/M(ove)

ESC(ape)

Erase current row and set all cells on the row to UND (undefined) status

Copies contents of first row specified to second row specified

Deletes current row and moves up following rows

Exchanges contents between first row specified and second row specified

Inserts blank row where specified and moves following rows down

Moves contents of first row specified to second row specified and adjusts contents of intermediate rows so no data are lost

Exits Worksheet-Edit Mode without performing any operation

The following screens are presented to illustrate the

procedures for copying and deleting one row of data. For copying

data, type "C" in the lower box of the edit screen, then tell the

program to copy data from Row 2 to Row 4 as shown below.

64



Section Top Depth Diameter Mom. of Inert. x inches

Area inches inches**4

; 30.00 0.00 inches'

30.000 30.000 47813.0000 707.0000 14906.0000

3 160.00 707.0000

30.000 47813.0000 4

707.0000

2 7 8 9


Blank Copy Delete Exchange Insert Move

Fl-Help : Help - / : Edit Screen- F8 :

Alt-X-Exit Continue -

Press <Enter> after the command is given, you will see the data

from Row 2 are also presented in Row 4.


Section

! 2 3

ii

! 8 9

10


Top Depth Diameter Mom. of Inert. Area inches inches inches**4 inches'

0.00 30.000 47813.0000 707.0000 30.00 30.000 14906.0000 707.0000

160.00 30.000 47813.0000 707.0000 30.00 30.000 14906.0000 707.0000


4 1:DEF:Num 0.00000

- : Move Cell - ? : Help - / : Edit Screen- F8 : Continue - Fl-Help Alt-X-Exit

65

If the user decides to erase Row 4, the user need to press the "/" key first, then type "D" in the lower box of the edit screen. The

screen will ask the user to specify a row number as shown below.




i! inches inches inches**4 inches'

0.00 30.000 47813.0000 707.0000 2 30.00 30.000 14906.0000 707.0000 3 160.00 30.000 47813.0000 707.0000 4 30.00 30.000 14906.0000 707.0000

65 7 8 9

10


Fl-Help I

Alt-X-Exit

Press the <Enter> key, the user will find data on Row 4 are removed as presented in the following screen.




i! inches inches inches**4 inches1

0.00 30.000 47813.0000 707.0000 2 30.00 30.000 14906.0000 707.0000 3 160.00 30.000 47813.0000 707.0000

:

4 8

1:



66

GUIDE FOR RUNNING MAIN PROGRAM (COM624P)

After an input file has been created and saved on the same

directory, press the <ALT> and <X> keys simultaneously to exit the

Input screen and return to the original Main Menu as shown below.

To execute the program, the user should move the cursor to "Run"

as shown on the top of the screen and press <Enter>. A normal run will end in less than one minute if a math-coprocessor is installed. The text output and graphics data will be created and

saved to the previously specified files, respectively. If an unexpected result is encountered, the program will stop running and an error message will be shown on the screen. Then, the user

should check the input data carefully. If Module COM624P is used as a stand-alone program, make sure to erase the file named

"COMFILE.DAT" if it exists in the same directory. This file is a temporary file to be used for the shell process.

File Input Run- Graphics






Fl-Help Alt-X-Exit

67

GUIDE FOR OPERATING GRAPHICS POSTPROCESSOR (C624VIEW)

After a successful run, the graphics data will be saved to the specified file. The user can move the cursor to "Graphics" shown on the top of the Main Menu and press <Enter> to open the

graphics window.

File Input Run Graphics +






Fl-Help Alt-X-Exit

The graphics window with pull-down menu is designed for C624VIEW. The configuration file, C624EDIT.CFG, must be on the same disk directory that contains C624VIEW.EXE. If there is no plot shown on the screen after the graphics data have been read

in, the user may need to again run the installation program

INSTVIEW.EXE, described in a previous section, to specify the

correct screen driver for the program. The detailed procedures

for using C624VIEW to obtain graphics will be presented in the

following section.

The driver supports the IBM color-graphics adapter (CGA), IBM

enhanced color-graphics adapter (EGA), Hercules graphics boards

and video-graphics array (VGA) . The graphics adapters and

68

printers supported by this graphics package are listed in Table

3.1. The distributor will not be responsible for modifying the

software for use on any graphics adapter or printer not listed or

not compatible to those listed in Table 3.1. The graphics program is easy to use and the procedures will be illustrated in this

section.

TABLE 3.1. DRIVER INFORMATION FOR GRAPHICS ADAPTERS AND PRINTERS

GRAPHICS ADAPTERS IBM Color-Graphics Adapter (CGA) IBM Enhanced-Graphics Adapter (EGA) IBM PC3270 Hercules Monochrome AT&T Indigenous Graphics Board IBM Video-Graphics Array (VGA)

PRINTERS Epson MX, FX, LX-80, 100, Okidata,

Panasonic, and Star Gemini Epson LQ IBM Proprinter Hewlett Packard Laser Jet and Desk Jet Hewlett Packard Pen Plotter

The Graphics Menu is displayed on the top line of the screen.

This menu has four submenus: File, Select, View, and Options. Any

of these selections may be chosen by highlighting the selection

using the cursor keys or by typing the first letter of the

selection ("V" for View, etc.)

When the Graphics Menu is active, a status report is

displayed on the screen below the Main Menu. This report shows

the number and size of any data sets stored currently in the

microcomputer's memory and indicates what data sets are currently

selected for viewing.

69

File View Plot Options

C624VIEW Version 2.0, Graphics Data: Number of p-y curves: NumPYcurve = 4 Number of load-response curves: NumCurves = 2 Number of point on load-response curves: Npts = 99 Units are Pounds & Inches p-y Curves selected for viewing

Response Curves selected for viewing

277520 bytes available Largest block contains 277520 bytes

The graphics data file is PLOTDATA

Alt-X Exit

70

The File Menu is used to read files of graphics data, show

the current subdirectory, change the logged subdirectory, or quit

the program and return to the disk-operating system. The selections in the File Menu are:

Read- to enter the name of the file to be read. If the file does not exist or is empty, a diagnostic message is displayed,

Directors - to display the directory of the current subdirectory,

- to change the logged subdirectory,

Quit- to quit UPVIEW and return to DOS, and


If the user has already specified in the Main Menu the file

name for the graphics data, the program will automatically read

and display it on the screen. However, if the user would like to

view the graphics under other file names, then the user can move

the cursor to "Readl@ and type the new file name as shown below.

71


Read Directory

-u

Change dir Quit to DOS Main Menu

Alt-X Exit

Move the cursor to the "Readgl, then press <Enter>.


Read File Name

Alt-X Exit

72

The View Menu is used to select the data sets to view under

the View option. The selections on the View Menu are:

g-v Curves - to select individual p-y curves for viewing. To select a p-y curve, the user tabs down to the desired curve using the cursor keys, then presses the space bar. An asterisk will mark any p-y curve to be displayed. Pressing the space bar a second time will turn off the selection. Finally, F8 is pressed to return to the Select Menu.

ResDonse Curves - to select individual curves for viewing that show the response of the pile. Pile-response curves are selected in the same manner as p-y curves,

Ultimate-Moment Curves - to select curves of moment versus curvature or curves of flexural rigidity (EI) versus moment for different axial-loading cases.

Interact'on Diagram - to select the interaction diagram (uliimate moment vs. axial load). In order to view the

diagram, the user must have selected at least three different axial loads for computation.

View Curves - to display the selected curves and to dump the graphics on the screen, and

Meu - to return to the Main Menu.

The user can type WIV1l or move the cursor to "View," then press the

<Enter> key to pull down the View Menu.

The p-y curves are displayed first (if selected), followed by

the pile-response curves for deflection, moment, shear, and soil

reaction, and followed by the moment-curvature curve, the EI-

moment curve, and the interaction diagram. The user clears the

display by pressing the <Enter> key.

73

File View Plot

p-y Curves Response Curves Ultimate Moment

El

Interaction Diagram View Curves Main Menu

Options

Alt-X Exit

A dump of the graphics from the screen is possible to any

Epson dot-matrix, IBM or HP laser jet, or any compatible printing

device. The dump is triggered by pressing the Control and "P"

keys simultaneously. The user can specify the type of printer

during installation or specify the printer in the Options submenu.

If no printer is connected or is turned off, the program will lock

until the printer is made available.

The following screens will illustrate the procedures to view

each graphic. Be sure to follow the instructional commands which

are printed directly below each screen for practice.

74

Option8 File View Plot

p-y Curves - Response Curves iUltimate Moment Interactive Diagram View Curves Main Menu

Alt-X Exit

Press Command Key: IPI l


Selection of p-y Curves for Viewing

Number Depth

ON 1 20.00 ON 2 60.00 ON 3 100.00 ON 4 150.00

Alt-X Exit

Toggle Viewing of Curves ON/off Using Space Bar-

F8 : Continue

Press Command Key: [I?81 l

75

Plot Options

Alt-X Exit Press Command Key: [RI l

File Vi8W Plot Options

Selection of Response Curves for Viewing

Number Deflection Nonmnt Shear Soil Reaction

1 ON ON off off

Toggle Viewing of Curves ON/off Using Space Bar+

F8 : Continue Alt-X Exit

Press Command Key: [FBI l

76

File view Plot

p-y Curves Response Curves Ultimate Moment +- Interactive Diagram View Curves Main Menu

ontions

Alt-X Exit Press Command Key: WI l


Selection of Moment, Curvature and EI Curves for Viewing

Number

t 3

Moment vs Curvature EI vs Moment

ON ON off off off off

Toggle Viewing of Curves ON/off Using Space Bar

L F8 : Continue Alt-X Exit

Press Command Key: LF81.

77

File view Plot OPtions

lp-y Curves ‘Responre Curves Ultimate Moment ,Interactive Diagram 'View Curves Main Menu c

Alt-X Exit Press Command Key: [II l


Selection of Curves Under Various Axial Loads for Viewing

Number Axial Load

ON 1 0.00 ON 2 100.00 ON 3 1000.00

Toggle Viewing of Curves ON/off Using Space Bar


Press commana hey: fF83.

78


Response Curves Ultimate Moment Interactive Diagram View Curves

AIC:-X Ex1.t

Press Command Key: WI l

0.0 0.5 1 .o 1.5 2.0 2.5 a.0 a.5

: : : : : : :

9.0 smo -.,.. i ..:... . . . ..I...................i.........i...................~........l.........~........~.........~........~.......

: ; : ; : : : f :

: : ; :

: : : : I : : : :

8.0 8.0 r . . ..i.............. ..:.,.......;.,..._ i i

. . . . . . . ..>....... :

i.........i.........~........,j,..,.....~.........;.........~......... : :

-::. : : : : : : .:. ,: : : : : : :

7.0 7.0 -.,......... . :. ..(_. . . . . . . . . . . . . . . ..L.........................~..................~.........~........~....... e : :

i : : : :

: : : : : :

i 1 J " Q

l 20 otiu .lUU v 150 PLOTDRTII Cnt1-P to Print Scrmn

79

-0.05 0.00 0.05 0.10

: : :

: : :

: i i i

__. . . j . . . ! . . ! .

: : : ;

:

4.0 5 :

i :

: : :

,,.,; ._._,..,.: . . . .._.... . . . . . . . . . . . . .._. i . . . . . . . . . . -:::: - : : : : ., ; -::I:::

4.5 5 : : : . . . . . . . . . . . . . . . . . . . . . ..~.........~........~.........~...... -:: j:;; -:.::

5.0 r : :

0.0

0.s

1.0

;

f

P.S

: 9.0

f a.s

PLOTOWl

Itmnsnt <Inch-Yios> <looo-s~

0.0 0.s 1.0

......

......

......

......

......

Cdl-P to prtnt term

Cdl-P to PrAnt tcrmal

80

1.00

curvrturr co. oool’ s>

2.00 2.00 4.00 s.00

2.4

20.0

18.0

16.0

14.0

12.0

cntn-P to Print term

1.0 2.0 2.0 4.0 5.0 6.0

: : : : 10.0 . . . ..-.....'....

: : :

8.0 1: ! . . . . . f : : : :

8.0 I...! . . . . . . . . . . . .

4.0

2.0

0.0

: : : : : : : f : : : : : : : : : : : :

Cdl-P to Print term

81

6.0 6.0 7.0 7.0 0.0 0.0 9.0 9.0

,,,:,,,,, ,,,,l,,,,

0.0

7.0

6.0

5.0

4.0

3.0

2.0

: : :

F+LOTOMA

- cdl-P to Print term

82

The Plot Submenu is used to select the sets of data and to

prepare the files on graphics for HP-plotters or plotter

emulators. The selections in the Plot Menu are:

p-y Cm - to select individual p-y curves for viewing. To select a p-y curve, the user tabs down to the desired curve using the cursor keys, then presses the space bar. An asterisk will mark any p-y curve to be displayed. If the space bar is pressed a second time, the selection will be eliminated. Returning to the Select Menu is accomplished by pressing F8.

Response CurveS - to select individual curves for viewing on the response of the pile. The curves are selected in the same manner as the p-y curves,

- to select curves of moment vs curvature or flexural rigidity (EI) vs moment for different axial-loading cases,

v - to select the interaction diagram (ultimate moment vs axial load). To view the interaction diagram, at least three different axial loads must have been used in the computations.

Generateal - to prepare the HD-LG-plot files and to select the pen speed, and


The pull-down menu shown below can be opened by pressing *'P@@

or moving the highlighted cursor to "Plot@@ followed by the <Enter> key. The following screen will be presented to illustrate the

procedures to create a HP-GL-PLOT file to send to the pen plotter.

83


.-

Alt-X Exit

Press Command Key: [RI .

File View Plot options

Selection of Responee Curves for Plotting

Number Deflection Moment Shear Soil Reaction

1 ON ON off off

Toggle Plotting of Curves ON/off Using Space Bar-


Press Command Key: IF81.

84


E&q

Alt-X Exit

Press Command Key: [Gl .


Preparing EiPGL plot file for p Enter file name for plotter fi Example. hpgw

p-y Curves Response Curves Ultimate Moment Interaction Diagram Generate Plots

e:

Select Pen speed (l=slowt38.1 for high quality, 100 for max speed SOW

A r1t-X Exit Press Command Key: [Enter].

85


C624VIRW Version 2.0, Graphics Data: Number of p-y curves: NumPYcurve = 0 Number of load-response curves: NumCurves = 0 Number of point on load-response curves: Npts = 0 Units are Pounds & Inches p-y Curves selected for viewing

Response Curves selected for viewing

212416 bytes available Largest block contains 212416 bytes

The graphics data file is D:PLOTDATA

Alt-X Exit Press Command Key: [ALTl [Xl l

86

After the HP-GL-plot files have been created, the user can

exit (Alt-x) to DOS and use the following DOS commands to get hard

copies from the HP-plotter.

C:> MODE COM1:9600,N,7,1,P <CR> (For DOS 4.01 or higher, using the following MODE COM1:9600,N,7,1,B <CR>)

C:> Print (HP-GL File-Name) <CR>

Some parameters used in the Mode command may vary with the

set-up of the hardware. The user should refer to the DOS Manual

for proper changes.

The Options selection of the Main Menu is used for several

options relating to the display of data on the screen. The user

can move the cursor to "Options" followed by the <Enter> key to

open the first window as shown below.

File View Plot options *

Optional Plotting Control Values - Screen 1 of 2

Symbol plotting increment .................... Upper y-value for p-y curves (in) ............ Limiting depth for response curve plots (in). Plotter X-coordinate for origin (in) ......... Plotter Y-coordinate for origin (in) ......... Plotter X-axis length (in) ................... Plotter Y-axis length (in) ...................

2.00: 600.000

1.750 1.500 8.000 5.000

Symbol plotting increment is 0 for no symbols, 1 for every symbol, 2 for every 2nd point, 3 for every 3rd point, and so on.

R 3:DEF:Num 6.0000000000E+02

: Move Cell -3 : Help - F2 : Edit Cell - F8 : Continue - Alt-X Exit

87

The first optional value is the increment used to mark individual

data sets with unique symbols. Any value of increment may be

used, including zero for no symbols at all. A legend defining the

Symbols used by UPVIEW is displayed on each graph.

The second optional value is the value of depth below which

no response of the pile is displayed. The program will normally

allow the user to view the curves showing the response of the pile

over the full length of the pile. By setting the length to

something less than the full length of the pile, the user may zoom

in on the area where the response is most often critical.

The third optional value is the y-value above which no p-y

data are displayed. This allows the user to zoom in on the p-y

values near the origin to examine the initial stiffness of the p-y

curves. The other options are for the format used by the pen

plotter. The most important option shown on the second window is

the selection of a printing device. The printer may already be

specified in the configuration file; however, the user may make a

change here. The code for printers must be set before the

command for "screen dump" can be sent.


Optional Plotting Control Values - Screen 2 of 2

Axis Title Character Size (in) . . . . . . . . . . . . . . 0.15000 Plotting Symbol Size (in) . . . . . . . . . . . . . . . . . . . 0.15000 Plotter Pen Number for Axis Titles . . . . . . . . . . 1 Plotter Pen Number for Axis and Borders . . . . . Plotter Pen Number for Data Line & Symbols . . : Type of Printer Used for Screen Dump . . . . . . . . 2 Codes for printers: 1 = Epson MX, FX

2 = Epson LQ 3 = Toshiba 24-pin 4 = HP LaserJet and DeskJet 5 = HP InkJet

= IBM Proprinter B = IBM Proprinter24.

All printer output is sent to LPTl. TO redirect LPTl to COMl use the DOS MODE command.

A 1:DEF:Num 1.5000000000E-01

: Move Cell - ? : Help - F2 : Edit Cell - F8 : Continue - Alt-X Exit

88

CHAPTER 4. INPUT INFORMATION AND DATA STRUCTURE

INTRODUCTION

A user-friendly, menu-input, preprocessor C624EDIT was

developed to create and edit input data for the computer program COM624P. C624EDIT is a full-screen editor and has an option t0

save and retrieve data files.

The user can also prepare an input file by following the

line-by-line input guide with any available text editor. The

structure of input data is presented in this chapter. It should

be noted that all the data entry is free-field format with a

maximum of 80 characters per line. Therefore, numerical data may

be entered in fixed, floating-point, or exponential format as

desired. A blank space is needed to separate two variables in the same line. The sequence of the line-by-line input format is

presented in Appendix A.

Data input is based on a coordinate system in which the pile

head (top of pile) is the origin and the positive x-direction is

downward (Fig. 4.1). The ground surface need not be at the

elevation of the pile head. Sign conventions are shown in Fig.

4.2.

Any convenient and consistent units of force and length can

be used. The program is set up to label the output in one of

three ways.

1. The user can designate that English units of inches and

pounds will be used, and output will be labeled accordingly.

89

Origin-b

X

Pile Head

-Y

Ground Surface

Tip of Pile

Figure 4.1. Coordinate system.

90

Load Diogrom

Shear Diagram

Positive Load

(0)

Positive Shear

(b)

Moment Dio gram

Poritive Moment

(cl

Slope Diagram Y

X

Positive Slope

(d)

Deflection Diagram

r Y vt II

X

Positive Deflection

(8)

Figure 4.2. Sign conventions.

91

2. The user can specify that SI units of kilonewtons and

meters will be used, and output will be labeled accordingly.

3. The user can use any other consistent units (the

computer does not need to know which ones) of force and length,

and output will be labeled in terms of forces and lengths (F and

L) l

Several default values may be used in data input. Where the

user desires to use a default value, the input should be left

blank for the relevant variable.

(In this section, the symbol 1tO1' denotes a capital letter 0;

the symbol "0" denotes the number zero.)

The following steps are recommended for preparation of input , of data.

1. Decide which units will be used for force and length.

2. Decide into how many increments the pile is to be

divided. Up to 300 increments are allowed. Be sure to satisfy

yourself that an adequate number of increments have been used to

obtain a satisfactory solution. Some trials will be helpful as

discussed in Part II on verification of results.

3. Decide whether p-y curves will be input or whether they

will be generated internally. If they are to be input, pick the

depth for each curve, pick the number of points to be input for

each depth, and tabulate the data. Up to 30 p-y curves are

allowed.

92

4. If p-y curves are to be generated internally, divide the

soil profile into from one to nine layers; decide which of the

following p-y criteria will be used for each layer:

l Matlock's (1970) criteria for soft clay;

l Reese et al. 's (1975) criteria for stiff clay below the water table;

l Welch and Reese's (1972) criteria for stiff clay above the water table;

l Reese et al. 1s (1974) criteria for sand; and/or

l Reese and Nyman's (1978) criteria for limestone.

Estimate undrained shear strength c and strain at 50 percent stress level E50 for clay layers; estimate the angle of internal

friction 4 for sand; and estimate the slope k of a plot of maximum

soil modulus Es versus depth x for all strata. Be sure to read the

background on any criteria that are used so that their basis and

limitations are thoroughly understood.

5. Select the length of the pile, the modulus of elasticity

of the pile material, and the x-coordinate of the ground surface

(x is equal to zero at the top of the pile).

6. Divide the pile into from one to 10 segments with

uniform cross-section. For each segment, tabulate the x-

coordinate of the top of the segment, the diameter of the segment,

the moment of inertia, and the pile cross-section area.

7. If there are any distributed lateral loads on the pile,

tabulate up to 10 points on a plot of distributed load versus

depth below top of pile.

93

8. Tabulate up to 10 points on a plot of effective unit

weight of soil versus depth. This step is not necessary if no p-y

curves are generated internally.

9. Tabulate up to 10 points on plots of c, Q, and &so versus

X. Skip this step if no p-y curves will be generated internally.

10. If p-y curves are generated internally in the program,

tabulate any depths for which p-y curves are to be printed.

Ordinarily, a few curves are printed for the purpose of verification.

11. Determine the loads to be applied to the top of the pile:

A. lateral load at pile head or lateral deflection at pile head;

B. second boundary condition at pile head, which can be either,

i. moment (&I,

ii. slope (St),

iii. rotational restraint (Mt/St); and

C. axial load (assumed to be uniform over full length of pile).

Up to 20 loading combinations can be input for each problem,

e.g., to generate a load-deflection curve.

94

SELECTION OF BOUNDARY CONDITIONS AT PILE HEAD

Four types of boundary conditions for the pile-head

connection are implemented in Program COM624P. These are

designated as Cases 1 through 4. The detailed information for modeling these boundary conditions is described in Chapter 2 of

Part II of this manual.

. Free to Rotatr DC=11

The lateral load (Pt), the bending moment (Mt), and the axial

load (Px) at the top of the pile are known. No rotational

restraint will be provided by the superstructure, and the rotation

at the top of the pile will depend only on the flexural rigidity

of the pile itself. If the above conditions are met, the user can

select this boundary condition for analysis. A typical example is

a pile that is used to support an overhead sign.

Frequently, the pile head is embedded into a monolithic

reinforced-concrete cap. Conceptually, if the flexural rigidity

of the pile cap is much stronger than that of a connected pile,

the rotation angle between the pile head and the monolithic cap is

unchanged with or without lateral bending. For such a case, the pile-head connection is defined as completely fixed and the

rotation of the pile head within the monolithic concrete cap is

assumed to be zero, in which case the slope (St) is set to zero.

However, if a small rotation at the pile-head connection is

allowed, the user can specify the slope (in radius) for the

computation. To apply the boundary condition in Case 2, the

lateral load (Pt), the slope or rotation (St) at the pile head, and

the axial load (Px) should be given.

95

The connection between the pile and the superstructure, such

as a steel frame, may not be always a perfectly rigid joint. If

the magnitude of the restraint between the pile and superstructure

can be estimated, and can be further expressed with a function of &/St (Mt and St are the bending moment and the slope angle at the

pile head, respectively), the elastically-restrained boundary

condition can be selected for use in Program COM624P. The elastic restraint Mt/St is largely affected by the stiffness of

superstructures. The superstructures are different in many ways;

therefore, the elastic restraint at each joint needs to be studied

by using a sound structural theory. If there is a nonlinear relationship between Mt and St, iteration may be required to

achieve compatibility. To apply this boundary condition, the lateral load (Pt), the elastic restraint (Mt/St), and the axial

load (Px) , at the top of the pile must be known.

If the pile-head deflection (yt), the bending moment (Mt), and

the axial load (Px) at the top of the pile are given, then the user

can use the boundary conditions in Case 4 for computation. The

deflection of the pile head can be restrained in either direction.

The reaction force at the pile head (restrained point) will be one

of the outputs of the program. This boundary condition can be

applied to piles which support a bridge abutment that has zero or

a very small allowable movement.

ITERATIONS OF COMPUTATIONS USING CRACXED/UNCRACICED EI GENERATED INTERNALLY BY SUBROUTINE PMEIX

A new feature of the second version of Program COM624P is

that the program will use a more rigorous approach to control the

96

use of cracked and untracked EI values during computation. The

subroutine PMEIX will compute the ultimate bending moment for the

selected section. For reinforced concrete sections, it will

compute the EI values for untracked sections and for cracked

sections. The user can manually input different EI values for

several sections after examining the computer curve for bending

moment and finding the length over which the moment distribution

to the cracked-section conditions will exist. Two or three

iterations may be required to achieve satisfactory results.

Program COM624P provides an option for the user to request the

computer to select values of EI internally for cracked or

untracked sections for use in the iterations.

Figure 4.3 shows the variation of bending moment and

associated cracked/untracked EI values. As it may be seen, only

the upper portion of the pile will be subjected to a large moment.

Because the upper portion of the pile needs greater stiffness, the

reinforcing steel can be enhanced only for that portion in order

to reduce the pile deflection.

97

160

,2 2 240

.3

o a20

480

! El, lb-in.2 x 10’

I 1 1 0 1’ 40 I 80 720

I 760 200 240

Moment, lb-in. x ,104-

D-30’ I

Steef Ratio-1.3% I

I I

Figure 4.3. Bending moment and flexural rigidity versus depth for a laterally-loaded pile.

98

CHAPTER 5. EXAMPLE STUDIES

INTRODUCTION

This chapter presents six examples that were studied by use

of COM624P. The first example is for a 14HP89 steel pile embedded in a single-layer deposit. The second example is for a

reinforced-concrete pile embedded in a multi-layer deposit. The

third example is for a pile embedded in a sloping abutment. The

fourth example is to illustrate the use of p-y curves entered by

the user. Examples 5 and 6 are included to illustrate the cases

in which the ultimate bending moment and design of reinforcement

are required.

The examples that follow are intended to demonstrate the

capability of the computer program and are not intended to be a

complete presentation of the design process. The publication

(FHWA-IP-84-11) entitled "Handbook on Design of Piles and Drilled

Shafts under Lateral Load" is highly recommended for engineers

seeking guidelines for design. There are a number of factors that

must be considered in design before and after the computer

execution.

A general procedure on proper use of the program was

developed by Christopher Dumas of FHWA during the design review

and analysis of a case study for pile-supported abutment. The

guidelines and procedures are presented in Appendix B.

The program gives output as follows:

Echo-print of input data,

Generated p-y curves,

99

Listing of pile deflection, bending moment, shear, soil resistance, and flexural rigidity along the length of the pile,

Summary results of pile-head deflection, maximum bending moment, and maximum shear force for various loading conditions, and

Listing of bending moment, EI, neutral axis, and concrete strain at each curvature.

From the variety of output that can be generated, the user should

be able to get all the needed information on the response of a

pile.

100

EXAMPLE 1, PILES IN A SINGLE LAYER OF SOIL

A 14HP89 H-pile is used for the foundation of a bridge

abutment. The width of the steel section is 14.7 in and the

length of the pile is 25 feet. The soil deposit is a uniform

stiff clay above the water table. The undrained cohesive strength

is 14 lb/sq in, the total unit weight is 0.069 lb/cu in, and the E50 is 0.007. The value of soil modulus (k) is assumed for

400/lb/cu inch. The user can estimate the value of k based on

Table 3.2 in Part 11 of this manual if k-values were not measured

for soils. The axial load is 39 kips and lateral loads at the

pile head are 40 kips and 20 kips respectively. The pile head is

assumed to be free to rotate.

This example was used by the Design Handbook (FHWA-IP-84-11)

in Section 3.5, Page 75. In regard to the aspects of design,

thorough discussions have been given in the handbook. The users

are encouraged to read that section. The strong axis of the pile

(Ix - 904 in4) will be used to resist the lateral load.

Therefore, the width (14.7 in) of the flange was used as the

equivalent diameter for the input required by Program COM624P.

The input file created by C624EDIT is presented on the next

page followed by a listing of the output data. The computed

maximum bending moment on the pile is less than the yield moment

(5.84 x lo3 in-kip) of the section. In this example the user can

increase the lateral load until the ultimate bending moment is * reached. The service load can be selected by dividing the maximum

lateral load, which creates the ultimate bending moment, with a

load factor. The load factor can be 2 to 2.5 depending on the

importance of the structure. The deflection under the service

load also needs to be satisfied by the design specifications. The

graphics display of p-y curves, pile-deflection curves, and

bending moment curves are also presented for verification.

101

The input and output data are shown in the following pages.

102

INPUT SCREENS FOR EXAMPLE 1

File- Analysis Mult Option




Fl-Help Alt-X-Exit


Read Read New New Save Save u u Directory Directory Change dir Change dir Quit to DOS Quit to DOS Main Menu Main Menu

I Fl-Help Fl-Help Alt-X-Exit Alt-X-Exit

105

File Analysis Mult

New File Name EXAMPLE.INl

Option EXAMPLE. IN1

1

Fl-Help Alt-X-Exit

File Analysis+ Mult Option


This Program is a preprocessor developed especially for users for Preparation of input for the computer program COM624P. The main menu for this program is displayed as a bar at the top row of the screen. The main menu has four choices: FILE, ANALYSIS, MULT, and OPTION.


Fl-Help Alt-X-Exit

106

File Analysis Mult

Title- Pile Properties Soil Properties Lateral p-y Data Data for Loading Computation Control Output Tables Main Menu

Fl-Help Alt-X-Exit

Option

File Analysis Mult Option EXAMPLE.INl

1 4 l:DEF:Lab EXAMPLE 1 PILES IN A SINGLE LAYER OF SOIL


EXAMPLE 1 PILES IN A SINGLE LAYER OF SOIL

: Move Cell - ? : Help - / : Edit Screen F8 : Continue - Fl-Help Alt-X-Exit

107

File Analysis Mult

Title Pile Properties+ Soil Properties Lateral p-y Data Data for Loading Computation Control output Tables Main Menu

Option

Fl-Help Alt-X-Exit

File Analysis Mult Option EXAMPLE. IN1


Number of increments (c= 3001 . . . . . . . . . . . . . . . . . . . . . Distance from top of pile to ground surface - inches Length of pile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pile modulus

inches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Psi

Slope of ground surface (degrees) . . . . . . . . . . . . . . . . .

120

300% 29000000

0.0000

i 1:DEF:Num 120

- : Move Cell - Fl-Help Alt-x-Exit?

: Help - / : Edit Screen- FE : Continue +

108



Section TOP Depth Diameter Mom. of Inert. Area # inches inches inches**4 inches= t 0.00 14.700 904.0000 26.1000

3 4

2 7 8 9

10


I A 1:DEF:Num 0.00000

: Move Cell - 7 : Help - / : Edit Screen----- FS : Continue - Fl-Help Alt-X-Exit


Title Pile Properties Soil Properties Lateral p-y Data Data for Loading Computation Control Output Tables Main Menu t

Fl-Help Alt-X-Exit

109


I Editing Soil Layer Information

Layer Criteria x-top X-bot k

! ! inches inches lb/in3

0.00 360.00 400.00 2 3 4

6" 7 8 9

10 p-y Curve Criteria

#1 = Soft Clay Criteria

:: = Stiff Clay Below Watertable ::

= stiff Clay Above Watertable = Sand

= Interp. Between Input Curves #6 = Vuggy Limestone

A 1:DEF:Num 3

1 : Move Cell - 3 : Help - / : Edit Screen- F8 : Continue - Fl-Help Alt-X-Exit



Point

: 2

:

2 7

: 10

Depth Unit Weight

inches 0.00 lb/in3 0.069 360.00 0.069

A 1:DEF:Nurn 0.00000

: Move Cell - : Help - / : Edit Screcv F8 : Continue - Fl-Help Alt-X-Exit?

110


I Editing Shear Strength Information I

Layer Depth ES0 # inches PST de:. e sob 0f c

1 0.00 14.000 0.00 0.0070 i 360.00 14.000 0.00 0.0070

4

z

l!

lo’

A 1:DEF:Num 0.00000

: Move Cell - 3 : Help - / : Edit Screen---- F8 : Continue 1 Fl-Help Alt-X-Exit

File Analysis Mult

Title Pile Properties Soil Properties Lateral p-y Data Data for Loading4 Computation Control Output Tables Main Menu

Option

Fl-Help Alt-X-Exit

111



Distributed lateral loading (y/n) ? ............... n Is loading cyclic (y/n) 7 ......................... n Boundary condition code (KBC) ..................... 1

KBC = 1 for shear and moment KBC = 2 for shear and slope KBC = 3 for shear and rotational restraint KBC = 4 for deflection and moment

A 1:DEF:Lab n L : Move Cell - ? : Help - / : Edit Screen- F8 : Continue - Fl-Help Alt-X-Exit



KOP

1 1

Shear Moment Axial Load pounds in-lbs pounds

20000.00 0.000 39000.00 40000.00 0.000 39000.00

I KOP=O if only a summary output for this load is to be printed =l if complete output is desired for this load

A 1:DEF:Nm 1 L : Move Cell - ? : Help - / : Edit Screen- F8 : Continue - Fl-Help Alt-X-Exit

112

File Analysis Mult

Title Pile Properties Soil Properties Lateral p-y Data Data for Loading Computation Control-4 Output Tables Main Menu

Option

Fl-Help Alt-X-Exit


Maximum number of iterations allowed for analysis : 100 Tolerance on solution convergence, inches : 0.000010 Value of deflection considered to be excessive, inches Computation using internal-generated cracked/untracked EIi N

147.0000

4 l:DEF:Num 100

- : Move Cell - ? : Help - / : Edit Screen- F8 : Continue /' Fl-Help Alt-X-Exit

113


~Title Pile Properties Soil Properties Lateral p-y Data Data for Loading Computation Control Output Tables4 Main Menu

&

Fl-Help Alt-X-Exit



*** Lateral Load Analysis l **

Printing Increment (1 for every node, 2 for every other node, etc) 2 Print deflection, moment, shear over full length of pile (y/n) Print p-y curves for verification ::

4 1:DEF:Num 2

- : Move Cell - 7 : Help - / : Edit Screen- F8 : Continue - Fl-Help Alt-X-Exit

114


Enter depths for which p-y curves are to be calculated for verification:

Point

i

: 5

;

i 10

Depth inches

20.00 60.00

100.00 150.00

A 1:DEF:Num 20.00000

F8 : Continue - Fl-Help

: Move Cell - ? : Help - / : Edit Screen- Alt-X-Exit

File Analysis Mult

Title Pile Properties Soil Properties Lateral p-y Data Data for Loading Computation Control Output Tables Main Menu-

Fl-Help Alt-X-Exit

Option

115


Save -

I

t

Fl-Help Alt-X-Exit

1

File Analysis Mult

Read New 1 Save

Save File Name EXAMPLE.INl

Option EXAMPLE.INl

?l-Help Alt-X-Exit

116

OUTPUT RESULTS FOR EXAMPLE 1


UNITS--ENGL

**************************************************u**********

PILE DEFLECTION, BENDING MOMENT, SHEAR & SOIL RESISTANCE *************************************************************

INPUT INFORMATION *********************************

TBE LOADING IS STATIC

PILE GEOMETRY AND PROPERTIES

PILE LENGTH = MODULUS OF ELASTICITY OF PILE =

1 SECTION(S)

X DIAMETER

IN IN .oo

14.700 300.00

SOILS INFORMATION

X-COORDINATE AT THE GROUND SURFACE

SLOPE ANGLE AT THE GROUND SURFACE

1 LAYER(S) OF SOIL

LAYER 1

=

I

.OO IN

.OO DEG.

THE LAYER IS A STIFF CLAY ABOVE THE WATER TABLE X AT TNE TOP OF THE LAYER s .OO IN XATTHEBOTTOMOFTHELAYER = 360.00 IN VARIATION OF SOIL MODULUS, k = .400E+03 LBS/IN**3

300.00 IN .2903+05 KIP/IN**2

MOMENT OF INERTIA

IN**4 IN**2

.9043+03 .261E+02

119

DISTRIBUTION OF EFFECTIVE UNIT WEIGHT WITH DEPTH 2 POINTS

X,IN WEIGHT,LBS/IN**3 .oo .69E-01

360.00 .69E-01

DISTRIBUTION OF STRENGTH PARAMETERS WITH DEPTH 2 POINTS

X,IN C,LBS/IN**2 PHI,DEGREES ES0 .oo .140E+02 ,000 .700E-02

360.00 .140E+02 .ooo .700E-02

FINITE DIFFERENCE PARAMETERS NUMBER OF PILE INCREMENTS = 120 TOLERANCE ON DETERMINATION OF DEFLECTIONS = .lOOE-04 IN MAXIMUM NUMBER OF ITERATIONS ALLOWED FOR PILE ANALYSIS = 100 MAXIMUM ALLOWABLE DEFLECTION = .15E+03 IN

INPUT CODES OUTPT = 1 KCYCL = 1 KBC =l KPYOP = 1 INC = 2


UNITS--ENGL

OUTPUT INFORMATION ***********************************

GENERATED P-Y CURVES

THENUMBEROF CURVE IS

THE NUMBEROF POINTS ON EACH CURVE

= 4

= 17

120

DEPTH BELOW GS DIAM

2200 1r700 LB&**2 LB;E**2 LB:%*3

E50

.lE+02 .lE+02 .7E-01 .700E-02 Y

X0 LB&

.ooo .274 395.168 .549 469.936 .823 520.070

1.098 558.852 1.372 590.914 1.646 618.471 1.921 642.771 2.195 664.590 2.470 684.451 2.744 702.719 3.018 719.664 3.293 735.490 3.567 750.356 3.842 764.387 4.116 777.686 5.145 777.686

DEPTH BELOW OS DIAM

6i:OO 1::700 LB&*'2 LB:%**2 LB:=*3

E50

.lE+02 .lE+OZ .7E-01 .700E-02 Y

.ZO LB&N

.ooo .274 558.061 .549 663.650 .823 734.449

1.098 789.217 1.372 834.496 1.646 873.412 1.921 907.729 2.195 938.543 2.470 966.590 2.744 992.388 3.018 1016.318 3.293 1038.668 3.567 1059.662 3.842 1079.477 4.116 1098.258 5.145 1098.258

121

DEPTH BELOW GS DIAM ES0

lo~:oo 1~~700 .lE+O2 .lE+02 .7E-01 .lOOE-02

Y P

.%O LBS/IN

.ooo .274 720.954 .549 857.364 .823 948.829

1.098 1019.583 1.372 1078.078 1.646 1128.354 1.921 1172.687 2.195 1212.495 2.470 1248.729 2.744 1282.058 3.018 1312.973 3.293 1341.847 3.567 1368.968 3.842 1394.568 4.116 1418.830 5.145 1418.830

DEPTH BELOW GS DIAM E50

15~:oo 1::700 LBS,:N**2 LB:%**2 LB:%*3

.lE+OZ .lE+02 .7E-01 .700E-02 Y

.ZO .274 .549 .823

1.098 1.372 1.646 1.921 2.195 2.470 2.744 3.018 3.293 3.567 3.842 4.116 5.145

LB&N ,000

924.570 1099.506 1216.803 1307.540 1382.555 1447.031 1503.885 1554.936 1601.403 1644.145 1683.791 1720.819 1755.601 1788.430 1819.545 1819.545

---------- *** -----e----

122

PILE LOADING CONDITION

LATERAL LOAD AT PILE HEAD APPLIED MOMENT AT PILE HEAD AXIAL LOAD AT PILE HEAD

= .200E+02 KIP = .OOOE+OO IN-KIP = .3903+02 KIP

.oo .145E+OO 5.00 .134E+OO

10.00 .123E+OO 15.00 .112E+OO 20.00 .lOlE+OO 25.00 .910E-01 30.00 .812E-01 35.00 .718E-01 40.00 .6293-01 45.00 .546E-01 50.00 .4683-01 55.00 .396E-01 60.00 .331E-01 65.00 .2723-01 70.00 .2193-01 75.00' .172E-01 80.00 .132E-01 85.00 .972E-02 90.00 .6823-02 95.00 .4443-02

100.00 .2553-02 105.00 .llOE-02 110.00 .3673-04 115.00 -.700E-03 120.00 -.117E-02 125.00 -.141E-02 130.00 -.150E-02 135.00 -.1453-02 140.00 -.132E-02 145.00 -.114E-02 150.00 -.938E-03 155.00 -.7293-03 160.00 -.5333-03 165.00 -.3633-03 170.00 -.2253-03 175.00 -.121E-03 180.00 -.511E-04 185.00 -.9933-05

X DEFLECTION MOMENT TOTAL SHEAR SOIL FLEXURAL STRESS RESIST RIGIDITY

IN IN IN-SUP LBS/IN**2 KIP LBS/IN KIP-IN**2 ***** ********** ********** ********** ********** ********** **********

.2623+08

.2623+08

.262E+08

.262E+08 .2623+08 .2623+08 .262E+08 .262E+08 .2623+08 .2623+08 .2623+08 .2623+08 .262E+08 .2623+08 .262E+08 .2623+08 .262E+08 .2623+08 .262E+08 .2623+08 .2623+08 .2623+08 .262E+08 .2623+08 .262E+08 .262E+08 .2623+08 .2623+08 .2623+08 .262E+08 .2623+08 .2623+08 .262E+08 .2623+08 .262E+08 .262E+08 .2623+08 .2623+08

.OOOE+OO

.9713+02

.1873+03

.2703+03

.3453+03

.413Iz+03

.4733+03

.524E+03

.5683+03

.6033+03

.630E+03

.6493+03

.6593+03

.6613+03

.6553+03 .6413+03 .6193+03 .5893+03 .553E+03 .5093+03 .4603+03 .4053+03 .3453+03 .2843+03 .227E+03 .1763+03 .130E+03 .8923+02 .546E+02 .2593+02 .287E+Ol

-.1463+02 -.2673+02 -.3393+02 -.3663+02 -.3533+02 -.3063+02 -.232E+02

.1493+04

.2283+04

.3023+04

.369E+04

.4303+04

.4853+04

.5343+04

.576E+04

.611E+04

.6403+04

.6623+04

.6773+04

.6853+04 .687E+04 .682E+04 .6703+04 .6523+04 .6293+04 .5993+04 .564E+04 .523E+04 .4793+04 .4303+04 .3803+04 .3343+04 .2923+04 .2553+04 .2223+04 .194E+04 .170E+04 .152E+04 .161E+04 .171E+04 .1773+04 .1793+04 .178E+04 .174E+04 .1683+04

.201E+02

.1863+02

.1723+02

.1573+02

.1423+02

.1273+02

.lllE+02

.9453+01

.781E+Ol

.615E+Ol

.4493+01

.283E+Ol .118E+ol

-.4563+00 -.206E+Ol -.3643+03 -.516E+Ol -.663E+Ol -.802E+Ol -.9323+01 -.105E+02 -.115E+02 -.1233+02 -.118E+02 -.108E+02 -.9783+01 -.8653+01 -.750E+Ol -.633E+Ol -.517E+Ol -.404E+Ol -.2953+01 -.192E+Ol -.9743+00 -.127E+OO

.613E+OO

.123E+Ol

.170E+Ol

.2673+03

.2793+03

.2903+03

.2993+03

.308E+O3

.3153+03

.3213+03

.3263+03

.3303+03

.3323+03

.3323+03

.332E+03

.329E+03

.3253+03

.3183+03 .310E+03 .2993+03 .286E+03 .270E+03 .250E+03 .224E+03 .1873+03 .805E+02

-.1763+03 -.2053+03 -.2211+03 -. 2293+03 -.2331+03 -.233E+03 -.2303+03 -.224E+03 -.2143+03 -.1983+03 -.180E+03 -.1593+03 -.1363+03 -.llOE+03 -.7293+02

123

190.00 .9253-05 195.00 .145E-04 200.00 .1243-04 205.00 .7723-05 210.00 .343E-05 215.00 .840E-06 220.00 -.529E-07 225.00 -.9813-07 230.00 -.127E-07 235.00 .6023-09 240.00 -.181E-13 245.00 .2893-18 250.00 -.4603-23 255.00 .732E-28 260.00 -.1163-32 265.00 .1853-37 270.00 -.2933-42 275.00 .4643-47 280.00 -.7333-52 285.00 .1163-56 290.00 -.183E-61 295.00 .2883-66 300.00 -.924E-71

-.145E+02 -.7553+01 -.257E+Ol

.4993+00

.186&+01

.184E+Ol

.857E+OO

.lOlE+OO -.967E-01 -.502E-02

.2743-04 -.4523-09

.7463-14 -.1233-18

.2033-23 -.3343-28

.5503-33 -.9053-38

.1493-42 -.245E-47

.4033-52 -.6633-57

.OOOE+OO

.161E+04

.1563+04

.152E+04

.150E+04

.151E+04

.151E+04

.150E+04

.150E+04

.150E+04

.1493+04

.1493+04

.1493+04

.1493+04

.1493+04

.149E+O4

.149E+O4

.1493+04 .149E*O4 .149E+04 .1491+04 .149E+O4 .1493+04 .149E+O4

.158E+Ol

.120E+Ol

.aolE+oo

.4373+00

.125E+OO -.113E+OO -.207E+OO -.921E-01

.1363-02

.107E-01 -. 4943-03

.lSOE-07 -.2393-12

.3813-17 -.6063-22 -.1333-28

.219E-33 -.361E-38

.5933-43 -.976E-48

.1613-52 -.2643-57

. OOOE+OO

.718E+O2

.8033+02

.7723+02

.6863+02

.5603+02

.3943+02 -.1963+02 -.2303+02 -.1393+02

.6543+01 -.512E+OO

.1573-04 -. 2503-09

.3963-14 -.6293-19

.9963-24 -.1573-28

.249E-33 -. 3933-38

.6183-43 -.9733-48

.1533-52 -.489E-57

.2623+08

.262E+08

.2623+08

.2623+08

.262E+08

.262E+08

.262E+08

.2623+08

.2623+08

.2623+08

.2623+08

.2623+08

.2623+08

.2623+08

.2623+08

.2623+08

.2623+08

.262E+08

.2623+08

.2623+08

.2623+08

.2623+08

.2623+08

COMPUTED LATERAL FORCE AT PILE HEAD COMPUTED MOMENT AT PILE HEAD COMPUTED SLOPE AT PILE HEAD

TBE OVERALL MOMENT IMmLANCE THE OVERALL LATERAL FORCE IMBALANCE

= .20000E+02 KIP = .OOOOOE+OO IN-KIP = -.221783-02

= .103E-09 IN-UP = .6123-08 LBS

OUTPUT SUMMARY

PILE HEAD DEFLECTION = .145E+OO IN MAXIMUM BENDING MOMENT = .6613+03 IN-UP MAXIMUMTOTAL STRESS = .6873+04 LBS/IN**2

NO. OF ITERATIONS = MAXIMUM DEFLECTION ERROR = .949E-:i IN

--------e- *** ---a------

PILE LOADING CONDITION

124

LATERAL LOAD AT PILE HEAD APPLIED MOMENT AT PILE HEAD AXIAL LOAD AT PILE HEAD

= .400E+02 KIP = .OOOE+OO IN-KIP = .390E+02 KIP

X DEFLECTION MOMENT TOTAL SHEAR SOIL FLEXURAL STRESS RESIST RIGIDITY

IN IN IN-RIP LBS/IN**2 KIP LBS/IN KIP-IN**2 ***** ********** ********** *It******** *******t** ********** **********

.oo .6233+00 5.00 .5863+00

10.00 .5493+00 15.00 .512E+OO 20.00 .4763+00 25.00 .441E+OO 30.00 .406E+OO 35.00 .372E+OO 40.00 .340E+OO 45.00 .308E+OO 50.00 .2783+00 55.00 .250E+OO 60.00 .2233+00 65.00 .197E+OO 70.00 .173E+OO 75.00 .lSOE+OO 80.00 .130E+OO 85.00 .lllE+OO 90.00 .931E-01 95.00 .7723-01

100.00 .630E-01 105.00 .504E-01 110.00 -3923-01 115.00 .2963-01 120'.00 .213E-01 125.00 .144E-01 130.00 .8673-02 135.00 .4053-02 140.00 .432E-03 145.00 -.230E-02 150.00 -.4283-02 155.00 -.5603-02 160.00 -.6393-02 165.00 -.6743-02 170.00 -.6733-02 175.00 -.6463-02 180.00 -.5993-02 185.00 -.5383-02 190.00 -.4703-02

.ooOE+OO .1493+04 .4033+02 .3a53+03 .262E+08

.197E+03 .3093+04 .3803+02 .4043+03 .2623+08

.3833+03 .4613+04 .360E+02 .4223+03 .245213+oa

.5593+03 .6043+04 .3383+02 .4383+03 .2623+08 .7243+03 .7383+04 .316E+02 .454E+03 .2623+08 .8783+03 .8633+04 .293E+02 .468E+O3 .2623+08 .102E+04 .9783+04 .2693+02 .481E+O3 .262E+08 .115E+04 .108E+05 .2453+02 4923+03 .1273+04 .118E+05 .2203+02 :503E+03

.262E+08

.262E+08 .1373+04 .126E+05 .1953+02 .512E+03 .2623+08 .146E+04 .1343+05 .1693+02 .519E+03 .2623+08 .154E+04 .140E+05 .1433+02 .5253+03 .262E+08 .161E+04 .1463+05 .116E+02 .530E+O3 .262E+08 .166E+04 .lSOE+OS .8973+01 .532E+03 .262E+08 .170E+04 .1533+05 .630E+Ol .5333+03 .262E+08 .1733+04 .1553+05 .3643+01 .5333+03 .2623+08 .1743+04 .1563+05 .9783+00 .5303+03 .2623+08 .1743+04 .156E+05 -.166E+ol .5263+03 .2623+08 .1723+04 .1553+05 -.4283+01 .5193+03 .2623+08 .170E+04 .1533+05 -.6853+01 .510E+03 .2623+08 .1663+04 .lSOE+OS -.9373+01 .4993+03 .262E+OB .160E+04 .1453+05 -.118E+02 .4853+03 .2623+08 .1543+04 .140E+05 -.1423+02 .468E+03 .2623+08 .1463+04 .1343+05 -.1653+02 .44aE+03 .2623+08 .1373+04 .1273+05 -.1873+02 .4243+03 .2623+08 .128E+04 .119E+05 -.2073+02 .3943+03 .2623+08 .117E+O4 .llOE+OS -.2263+02 .355E+03 .262E+O8 .105E+04 .lOOE+OS -.2433+02 .301E+03 .2623+08 .9253+03 .9023+04 -.2553+02 .176E+O3 .262E+08 .798E+03 .798E+O4 -.2483+02 -.2743+03 .262E+08 .6783+03 .700E+04 -.2333+02 -.3273+03 .262E+08 .5653+03 .6093*04 -.2163+02 -.3563+03 .2623+08 .4623+03 .525E+O4 -.1983+02 -.3683+03 .2623+08 .367E+03 .448E+04 -.180E+02 -.3733+03 .2623+08 .2a23+03 .3793+04 -.161E+02 -.3733+03 .2636+&2 .2063+03 .317E+04 -.1423+02 -.3693+03 .262E+OS .140E+03 .263E+04 -.1243+02 -.3623+03 .2623+08 .8223+02 .2163+04 -.106E+02 -.3523+03 .2623+08 .3343+02 .1773+04 -.889E+oi -.3403+03 .2623+08

125

195.00 -.398E-02 200.00 -.327E-02 205.00 -.2603-02 210.00 -. 198E-02 215.00 -.145E-02 220.00 - .994E-03 225.00 -.6313-03 230.00 -.3563-03 235.00 -.162E-03 240.00 -.3793-04 245.00 .311E-04 250.00 .6063-04 255.00 .6463-04 260.00 .5433-04 265.00 .3843-04 270.00 .2263-04 275.00 .104E-04 280.00 .310E-05 285.00 .1283-06 290.00 -.2453-06 295.00 -.153E-08 300.00 .5383-13

-.6823+01 -.3893+02 -.6323+02 -.802E+02 -. 9043+02 -. 942E+02 -.9223+02 -.850E+02 -.7353+02 -.5823+02 -.4133+02 -.2663+02 -.1473+02 -.580E+Ol

.332E+OO

.390E+Ol

.521E+Ol .466E+Ol .2753+01 .580E+OO

-.4463+00 .OOOE+OO

.1553+04

.181E+04

.201E+04

.2153+04

.2233+04

.2263+04

.2243+04

.2193+04

.2093+04

.1973+04

.1833+04

.171E+04

.161E+04

.1543+04

.150E+04

.153E+04

.1543+04

.1533+04 .152E+04 .150E+04 .150E+04 .1493+04

-.722E+Ol -.563E+Ol -.412E+Ol -.2693+01 -.137E+Ol -.163E+OO

.930E+OO

.189E+Ol

.271E+Ol

.3343+01

.32OE+Ol

.2663+01

.207E+Ol .150E+Ol .962E+OO .4793+00 .6573-01

-.260E+OO -. 459E+OO -.3323+00

.219E-01

.OOOE+OO

-.327E+03 -.311E+03 -. 2943+03 -.274E+03 -.2543+03 -.2313+03 -.2063+03 -.1793+03 -.1473+03 -.102E+03

.9693+02

.115E+03

.116E+O3

.lllE+03

.102E+O3

.8953+02

.7373+02 .5443+02 .2663+02

-.254E+02 .3293+01

-.517E-01

.2623+08

.2623+08

.2623+08

.2623+08

.2623+08

.2623+08

.2623+08

.2623+08

.2623+08

.2623+08

.2623+08

.2623+08

.2623+08

.2623+08

.262E+08

.2623+08

.262E+08

.2623+08 .2623+08 .262E+08 .2623+08 .2623+08

COMPUTED LATERAL FORCE AT PILE HEAD COMPUTED MOMENT AT PILE READ COMPUTED SLOPE AT PILE BEAD

THE OVERALL MOMENT IMBALANCE TRE OVERALL LATERAL FORCE IMBALANCE

= .40000E+02 KIP =: .OOOOOE+OO IN-ICIP = -.745023-02

= -.2783-07 IN-KIP = .5633-06 LBS

OUTPUT StlmARY

PILE READ DEFLECTION = .6233+00 IN MAXIMUM BENDING MOMENT = .1743+04 IN-KIP MAXIMUMTOTALSTRESS = .1563+05 LBS/IN**2

NO. OF ITERATIONS I 27 MAXIMUM DEFLECTION ERROR = .8803-05 IN

SUMMARY TABLE *************************

LATERAL BOUNDARY AXIAL MAX. MAX. LOAD CONDITION LOAD MOMENT STRESS

(KIP) BC2 (KIP) ( I::IN ) (IN-KIPI (LBS/IN**2 .200E+02 . OOOE+OO .3903+02 .145E+OO .400E+02 . OOOE+OO

-.2223-02 .3903+02

.661E+O3 .6233+00

.6873+04 -.7453-02 .1743+04 .1563+05

126

y (IndIes)

0.0 1.0 20.0 2.0 3.0 4.0 5.0 6.0 7.0

. . . . : 1*-o : : : : . : : : : : i i ; . . . . . . . . . . . . ..~........~........~........~........~........~ . . . . . . . . . . 16.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

&Fy? . . . . ~ . . . . . ~ . . . . ~ . . . . (

14.0

12.0

10.0

8.0

6.0

4.0

2.0

. . . . . . . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . .

. . .

. . .

. . .

. . . . . . . . . . .

. . . . . . . . . . .

. . . . . . . . . . .

. . . . . . . . . . .

. . . . . . . . . . . . . . .

. . - . . . . . . - . . . . . . . . . “ . . . . . . . . . . . . . . . . . . . . . . . . . . - . . . . . . . . . . . . . . . . . : . . . . . . . . . . . . . . . . . . . . . . . . . . - . . . . . . . ” . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . .

. . . . . . . . . . . . .

. . . . . . . . . . . . .

. . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . - . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - . . . . . . . “ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - . . . . . . .~ . . . . . . . .

. . . . . . . . . . . . .

c.-.... ..!........!........!........~..........................,.................~..................~ . . .

............. ............. ............. : : : : : : : : : : : : :

Depth

0 20 inches 0 60 inches

A 100 inches

'I 150 inches

4

p-y Curves.

127

Deflection (Inches)

‘; .

8 1

-0.5 0.0 0.5 1.0 1.5 0.1

1c1111 lllltllll ’ . . :

0.1 . . .

~.......+.......:*........,i........ . . . . . . . . . . . . . . . . .

1.0 i . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.5

17

; . . . . l . . . . . . . . . . . . . . . j . . . . . . . . i . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . : : :

. . . . .

* , . : : ; ; ; I

“ “ f . . . . . . . . . . . . . . . . ! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . .

1: f

. . . ; : . . . * . 2.5 . . . . . . . . . . . . . . . . . . . . . j . . . . . . . . j . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2,0 : : : ; ; i . . . ..“...... . . . . . . ..!........!.................*................. . . . . . . . 2.5

1.0

1.5

5.0

. . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . . . . . . “ . . . . . . . - . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - . . . . . . . ” . . . . . . .

. . . . . . . . . . * . . .

. : : : : : :

. . . . . . .

. . . . . . . . . . . - . . . . . . . - . . . . . . . . . . . . . . . . . . . . . . . . . . ~ . . . . . . . - . . . . . . . ” . . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

0 1 0 2

Pile Deflection vs. Depth.

128

Ploment C Inch-Kips) <1000’s)

-1.0 0.0 1.0 2.0 0.0 3.0 ,I ,,,,..,.. ._.._ I I I I.1 I I I

1’““;‘1’; “I 1”“‘:“” I”’ 0.5

P.

-q L.. 1 I I:

. . .;. . . . .;. . . . . :;-.\ .9’::---- i .“‘I I

: f ..y; ,.... ...I . . . . . . . . . I... . . . . . . -7 : I

1.0

I.5

2.0

2.5

. . . . .: . . . .

F . . . . 1. . . . . k....

3.0 b . . . . . . . . . . . . . . af . . . . . . . . . . . . . . . . . . . . . . .._.I . . . . . . . . . . . . . . . . . . . . . . . . . . . / 3.5 E- : : : : : : : : . . . . . . . . . . . . . ..‘.........~........I........C_................._i........ I

Bending Moment vs. Depth.

129

Shear-CKips)

2.5

I- : : : : 4.0 p . . . . . . . . . . . . . . . . . . . . . _ . . . . . . . . . . 4.5 1: i m 8 m; 8 . . . ..-.........~........-................._........~........._....... 5,0-. : : : : : : :

Shearing Force vs. Depth.

130

‘; . I rl V

f 8 0

Soi 1 Ihact im WamWIneh) MNNY L)

-0.5 0.0 0.5 1.0 1.5

1.0

. . .

. . . . f . . . . . . * . . ~ . . . . . . . . ~ . . . . . .

\ : . . .

. . . .

. . .

L-b :

. . . .

: : . . . . . . . * . . . . y . . . . . . . z . . . . . . .

. . . . . . ; . . *

. : : : : * . I

. . . . . . I . . . ..+.......+.......+....... . . . . . . . . . . . . . . ,.......;.........>.......+....... . .

1.5

2.0

2.5

3.0

1.0

1.5

5.0

....... .... . ...... ..~.................,.................* ................ .... .... : : :

. . . . . .

. . . . . . .

. . . . . . .

. . . . . . . . . . . . . . . . . . . . - . . . . . . . “ . . . . . . . . . . . . . . . . . . . . . . . . . . - . . . . . . . . . . . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . . . . . . . . . . . . . . . - . . . . . . . ~ . . . . . . . . . . . . . . . . . . . . . . . . . . - . . . . . . . ” . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

a 1 0 2

Soil Reaction vs. Depth.

131

EXAMPLE 2, CONCRETE PILES IN LAYERED SOIL WITH DISTRIBUTED LOAD

This example is included to illustrate a common case in which

a 36-in diameter, reinforced-concrete pile is subjected to both

horizontal and vertical forces at the top of the pile.

Distributed loads are also specified near the top portion of the

pile. The soil deposit is not uniform and, as shown in Fig. 5.1,

five different layers are encountered in this example.

The recommendations for p-y curves for layered soils are

presented in Chapter 3 of Part II of this manual. The computer

will calculate the equivalent thickness for each layer. If the

user wants to check the p-y curves generated by the computer, the

equivalent thickness should be taken into account. The p-y curves

for rock at the fifth layer were generated internally by the

computer. The only parameter that is needed for rock is the shear strength. The modulus k and &SO are only used for the initial

condition. It should be noted that the shear strength is half of

the uniaxial compression strength reported for most rock

specimens.

Layered-soil is commonly encountered in routine design. It

should be noted that there may be some uncertainty regarding the

theory used for conversion of layered soils. If soil layers do

not change their natural properties dramatically (for example,

sandy layers with differing angles of friction) then the best

approach for modeling the soil response is to use a lower number

of layers. However, care must be taken to characterize in detail

the strength variation profile in the input data.

The input and output data are shown in the following pages.

133

kips

20 in.1 -

Stiff Clay

Sand

Soft Clay

Stiff Clay

Limestone

Pile Length - 500 in. Pile Diameter - 36 in.

in-kip

c = 2000 lb/sq ft. y- 125 lb/cu ft.

E - 0.005 50

$- 30 deg

f- 60 lb/cu ft.

c - 800 lb/sq ft. f- 60 lb/cu ft.

e - 0.02 50

--

c * 3000 lb/sq ft.

Y,'I 60 lb/cu ft.

& - 0.005 50

?/- 60 lb/cu ft.

c = 408,816 lbhq ft.

6 Modulus of Elasticity - 3.1 X 10 lb/sq in.

60 in.

120 in.

60 in.

144 in.

Figure 5.1. Data for Example 2.

134

INPUT SCREENS FOR EXAMPLE 2

File+ Analysis Mult

C624EDIT 2.0, Edit variables:

Option



I I Fl-Help Alt-X-Exit


New -

Fl-Help Alt-X-Exit

137


ii?---] New File Name

RXAMPLE.IN2 I

Change dir Quit to DOS Main Menu I

Fl-Help Alt-X-Exit


L Fl-Help Alt-X-Exit

138

File Analysis+ Mult Option




Fl-Help Alt-X-Exit

File Analysis Mult

I

option

Title - Pile Properties

soil Properties Lateral p-y Data Data for Loading

lComputation Control IOutput Tables Main Menu

'l-Help Alt-X-Exit

139



EXAMPLE 2 CONCRETE PILES IN LAYEBED SOIL WITH DISTRIBUTED LOADS

I A 1:DEF:Lab EXAMPLE 2 CONCRETE PILES IN LAYERED SOIL WITH DISTRIBUTED LOADS

: Move Cell - 7 : Help - Fl-Help

/ : Edit Screen--- 18 Alt-X-Exit

: Continue -

File Analysis Mult

Title Pile Properties4 Soil Properties Lateral p-y Data Data for Loading Computation Control Output Tables Main Menu

Option

Fl-Help Alt-X-Exit

140

File Analysis Mult option EXAMPLE.IN2


Number of increments (<= 300) ..................... Distance from top of pile to ground surface - inches Length of pile .............................. inches Pile modulus ................................ slope of ground surface (degrees)

Psi .................

100 20.0

500.00 3100000

0.0000

A 1:DEF:Num 100

- : Move Cell - 7 : Help - / : Edit Screen- F8 : Continue I J Fl-Help Alt-X-Exit




r inches inches inches**4 inches2

0.00 36.000 82500.0000 1080.0000 2 300.00 36.000 61500.0000 1080.0000

: 5 6 7 8 9

10



141


Title Pile Properties4 Soil Properties Lateral p-y Data Data for Loading Computation Control Output Tables Main Menu

Fl-Help Alt-X-Exit

File Analysis Mult Option BXAMPLE.IN2

Editing Soil Layer Information

Layer Criteria x-top X-bot : 1 inches 20.00 inches 80.00 1000.00 lbFin3

2 : 80.00 200.00 60.00 :

ii

260.00 200.00 404.00 260.00 1200.00 200.00

2 404.00 600.00 2000.00

7

i 10

p-y Curve Criteria tl = Soft Clay Criteria #3 = Stiff Clay Above Watertable #2 = Stiff Clay Below Watertable #4=Sand 15 = Interp. Between Input Curves 16 = Vuggy Limestone

A 1:DEF:Num 3 L : Move Cell - Ah-X-Exit?

: Help - / : Edit Screen--- F8 : Continue Fl-Help

142

File Analysis Mult option ExAMPLE.IN2


Point

r :

:

;

"9 10

Depth inches

20.00 80.00 80.00

600.00

Unit Weight lb/in3

0.072 0.072 0.035 0.035

A l:DEF:Num 20.00000

: Move Cell - ? : Help - / : Edit Screen- F8 : Continue . Fl-Help Alt-X-Exit


Layer #

I

2'

: 5

;

ii 10

Depth C inches psi de:.

ES0 e 508 0f c

20.00 13.900 0.00 0.0050 80.00 13.900 0.00 0.0050 80.00 0.000 30.00 0.0000

200.00 0.000 30.00 0.0000 200.00 5.560 0.00 0.0200 260.00 5.560 0.00 0.0200 260.00 20.800 0.00 0.0050 404.00 20.800 0.00 0.0050 404.00 2839.000 0.00 0.0010 600.00 2839.000 0.00 0.0010


A 1:DEF:Num L 20.00000

: Move Cell - ? : Help - / : Edit Screen F8 : Continue - Fl-Help Alt-X-Exit

143

File Analysis Mult

Pile Properties Soil Properties Lateral p-y Data Data for Loading + Computation Control Output Tables

Option

1

Fl-Help Alt-X-Exit

File Analysis Mult Option EEAMPLE.INZ


Distributed lateral loading (y/n) 7 . . . ..*...**.... Is loading cyclic (y/n)

Y ? . . . . . . . . . . . . . . . . . . . . . . . . . n

Boundary condition code (ICBC) . . . . . . . . . . . . . . . . . . . . . 1

I

ii: = 1 for shear and moment = 2 for shear and slope

KBC = 3 for shear and rotational restraint ICBC = 4 for deflection and moment

A 1:DEF:Lab y L : Move Cell - Alt-X-Exit?

: Help - / : Edit Screen--- F8 : Continue I B Fl-Help

144

File Analysis Mult Option HXAMPLE.IN2

Editing Distributed Loading on Pile

Point Depth

r inches

Loading pounds/inches

2 0.00 50.00 3 10.00 100.00 4

2 7

8 10

A 1:DHF:Num 0.00000

- : Move Cell - ? : Help - / : Edit Screen---- F8 : Continue I Fl-Help Alt-X-Exit



KOP Shear Moment Axial Load pounds in-lbs pounds

1 50000.00 100000.000 100000.00

KOP-0 if only a summary output for this load is to be printed =l if complete output is desired for this load

A 1:DEF:Num 1

: Move Cell - ? : Help - / : Edit Screen- FS : Continue I Fl-Help Alt-X-Exit

145


Title Pile Properties Soil Properties Lateral p-y Data Data for Loading Computation Control Output Tables Main Menu

Fl-Help Alt-X-Exit

File Analysis Mult Option EXAMPLE.INZ

Maximum number of iterations allowed for analysis Tolerance on solution convergence, inches

: 100 :

Value of deflection considered to be excessive, inches 0.000010

Computation using internal-generated cracked/untracked III: N 360.0000

1

A 1:DEF:Num 100

: Move Cell - Fl-Help Alt-X-Exit?

: Help - / : Edit Screen- FE : Continue I

146


Title Pile Properties Soil Properties Lateral p-y Data Data for Loading Computation Control Output Tables4 Main Menu

Fl-Help Alt-X-Exit

File Analysis Mult Option B:EXAMPLE.IN?


*** Lateral Load Analysis ***

Printing Increment (1 for every node, 2 for every other node, etc) 2 Print deflection, moment, shear over full length of pile (y/n) Y Print p-y curves for verification Y

iA 1:DEF:Num 2

1 : Move Cell - ? : Help - / : Edit Screen- F8 : Continue - Fl-Help Alt-X-Exit

147

File Analysis Mult Option B:EXAMPLE.INZ

Enter depths for which p-y curves are to be calculated for verification:

Point Depth inches

1 2

60.00

3 120.00 240.00

4 360.00 5

4 8 9

10

A 1:DEF:Num L 60.00000

: Move Cell - 3 : Help - / Fl-Help

: Edit Screen--- F8 Alt-X-Exit

: Continue -

File Analysis Mult

Title Pile Properties Soil Properties Lateral p-y Data Data for Loading Computation Control Output Tables Main Menu+-

Option

Fl-Help Alt-X-Exit

148

File + Analysis Mult Option

I C624EDIT 2.0, Edit Variables: I This program is a preprocessor developed especially for users for preparation of input for the computer program COM624P. The main menu for this program is displayed as a bar at the top row of the screen. The main menu has .four choices: FILE, ANALYSIS, MULT, and OPTION.

The selection of the FILE menu allows the user to access a pull- down menu for file operations such as reading in an existing file, creating a new data file, checking files in the directory, and similar operations. The sele tion of the ANALYSIS menu allows the user to enter required data f 1 r computing the response of the pile and soil, such as distributions of deflebtion, bending moment, shear, and soil resistance as a function of length along the pile. The selection of the MULT menu allows the user to enter data of a selected pile siee .for computing the ultimate bending,moment and other design-related information. The OPTION menu is used for screen setting and it may not be needed 'for most computer systems.

I Fl-Help Alt-X-Exit

1 Fl-Help Alt-X-Exit

File Analysis

Read New Save - -c Directory Change dir Quit to DOS Main Menu

Mult Option

149

File Analysis Mult Option B:?ZXAMPLE.IN2

“2g-j

save File Name EXAMPLE.INZ

Main Menu 1

Fl-Help Alt-X-Exit

150

OUTPUT RESULTS FOR EXAMPLE 2

EXAMPLE 2 CONCRETE PILES IN LAYERED SOIL WITH DISTRIBUTED LOADS

UNITS--ENGL

**********************************t**************************** PILE DEFLECTION, BENDING MOMENT, SHEAR & SOIL RESISTANCE *************************************************~*********~~

INPUT INFORMATION *********************************

DISTRIBUTED LOAD CURVE 3 POINTS X,IN LOAD,LBS/IN

.oo .500E+02 10.00 .lOOE+03 20.00 .200E+03

THE LOADING IS STATIC

PILE GEOMETRY AND PROPERTIES

PILE LENGTH = 500.00 IN MODULUS OF ELASTICITY OF PILE = .310E+04 KIP/IN**2

2 SECTION(S)

X DIAMETER MOMENT OF INERTIA

IN IN IN**4 IN**2 .oo

36.000 .8253+05 .108E*04 300.00

36.000 .6153+05 .10m+04 500.00

SOILS INFORMATION

X-COORDINATE AT THE GROUND SURFACE = 20.00 IN

153

Com624 Manual

Documents

Transcript of Com624 Manual