ColorGraze Powercore · install, letting you focus on the visual impact of your lighting design...

ColorGraze PowercoreLinear exterior LED wall grazing fixture with intelligent color light

ColorGraze Powercore Product Guide2

ColorGraze Powercore Linear exterior LED wall grazing fixture with intelligent color light

Easy to installWith flexible mounting options, multiple fixture length and beam angle options, integrated Powercore technology, and a discreet low-profile housing rated for use in outdoor locations, ColorGraze Powercore offers high performance and simple installation.

• Tailorlightoutputtospecificapplications— Available in three standard lengths, with standard 10º x 60º and 30º x 60º beam angles. Individually addressable 1 ft (305 mm) segments accommodate finecontrolofcolor-changingeffectsandpre-programmed light shows.

• High-performanceilluminationandbeamquality—ColorGrazePowercoredeliversupto368lumens of color-changing light per foot. Superior beamqualityoffersstriation-freesaturationasclose as 6 in (152 mm) from fixture placement with no visible light scalloping between fixtures.

• IntegratesPowercoretechnology—Powercoretechnologyrapidly,efficiently,andaccuratelycontrols power output to ColorGraze Powercore fixturesdirectlyfromlinevoltage.ThePhilipsData Enabler Pro merges line voltage with control anddeliversthemtothefixtureoverasinglestandard cable, dramatically simplifying installation and lowering total system cost.

• Versatileinstallationoptions—Constanttorquelocking hinges offer simple and consistent position controlfromvariousangles.Thelow-profilealuminum housing accommodates placement within most architectural niches.

• Superiorcolorconsistency—Optibin,aproprietary binning optimization process developed by Philips Color Kinetics, guarantees consistencyofhueacrossLEDs,fixtures,andmanufacturing runs.

• Industry-leadingcontrols—ColorGrazePowercore works seamlessly with the complete Philips line of controllers, including Light System Manager, iPlayer 3, and ColorDial Pro, as well as third-party controllers.

• Supportforinstallationsrequiringconduittofixtures—ColorGrazePowercoreConduitfixtureshaveflyingleadsandthreadedopeningsfor1/2inNPTconduittosupportinstallationsinNorthAmericawhereconduitisrequired.

• Customconfigurationsforspecialapplications— Standardconfigurationsusechannelsofred,green, and blue LED sources to produce a full range of RGB colors. You can create custom configurationstosupportspecialapplicationsby exchanging the LED sources in any channel. Optionsincludeeightcolortemperaturesrangingfrom a warm 2700 K to a cool 6500 K, Royal Blue, Blue, Green, Amber, and Red. Additional beam angles (including 9° x 9°, 10° x 30°, and 90° x 60°) are also available. See the ColorGraze Powercore OrderingInformationspecificationsheetforcomplete details.

ColorGraze Powercore linear LED lighting fixtures are optimized for surface grazing, wall-wash lighting, and efficientsignageillumination.Superiorlightqualityoffersuniformbeamsaturationascloseas6in(152mm).A compact, low-profile design combined with flexible mounting options allows for discreet placement within a wide range of architectural features. Intelligent, controllable fixtures are available in standard full-color configurations. Build-to-order configurations with additional beam angles and custom channels of white or color LEDs are also available to support special applications.

Photo Credits: Hedrich Blessing

ColorGraze Powercore Product Guide 3

Superior Grazing and Wall Washing — Inside and Outside

ColorGraze Powercore LED grazing fixtures from Philips Color Kinetics are easy to install, letting you focus on the visual impact of your lighting design rather than on setup and configuration. With ColorGraze Powercore, you can tailor light output to specificapplications—enhanceanareawithsmooth,wall-washinglight,orhighlighttextures by grazing textured surfaces such as brick and stucco. For added affect, you canuseacombinationofwall-washingandgrazingtechniquestodevelopavisuallytransitionalspace—drawinginterestfromtheinteriorofastructuretotheexterior,for example.

With a DMX- or Ethernet-based lighting controller such as ColorDial Pro, iPlayer 3, or Light System Manager, you can play pre-set effects or custom light shows at the touch of a button, or schedule light shows according to the day of the week, date, a recurring time, or an astronomical event such as sunrise or sunset.

Becauseoftheirlongsourcelife(80,000hoursormoreat50%lumenmaintenance),ColorGrazePowercorefixturesallowinstallationindifficult-to-accesslocations—crane-accessiblefeaturesonabuildingexterior,forexample—withoutthemaintenance concerns associated with traditional lighting sources.

Photo Credits: Hedrich Blessing


Versatile Installation OptionsColorGraze Powercore offers vibrant color and color-changing light ideal for surface grazing, wall washing, and signage lighting applications.

Philips offers a range of controllers to support installations from the simplest to the most complex. A simple installation might use twenty ColorGraze Powercore fixtures, an iPlayer 3 controller, and one Data Enabler Pro to illuminate a retail display with color-changing effects. A larger installation might use the Ethernet-based Light System Manager controller and multiple Data Enabler Pro devices to display light shows via hundreds of ColorGraze Powercore fixtures installed within a mix of interior and exterior architectural niches.

Regardless of the size and complexity of your installation, the planning time you spend up front can help streamline the installation and configuration of your fixtures. Keep these points in mind as you plan your installation:

• Createalightingdesignplanthatidentifiesandlocatesallfixtures,DataEnablerProdevices,andcontrollers.UsethisProductGuideandtheonlineConfigurationCalculatortodeterminewhethertoinstallfixturesinseriesorinparallel,howmanyfixturesyoucaninstallin a single run, and the maximum distances between DataEnablerProdevices,fixtures,andcontrollers.

• Forhigh-contrastsurfacegrazing—forexampletohighlightuniquetexturesorfeatures—place10ºx60ºfixtureswithin4in(102mm)ofawallorothersurface, with the light beam parallel with the wall or surfaceForsmoothwall-washinglightthatreflectsaglare-free ambient glow into the surrounding area, use 30ºx60ºfixturesandplacethematagreaterdistance from the wall or surface, with the light beam parallel with or at a small angle towards the wall or surface.

• Toaidinaddressingfixturesforcolor-changinglightshows,recordtheserialnumberofeachfixtureasyou assign it to your lighting design plan, and create a layout map that records the address or position of eachfixturewithinasequenceoffixtures.

• Determinewhethertoaddressfixturesandconfigureyourlightingsystemofflineorinteractively.Withofflineconfiguration,youstageandconfigureyoursystemoff-site,priortoinstallation.Offlineconfigurationcanbeconvenientwhenfixturesareto be installed in multiple locations or locations with difficultaccess.Interactiveconfigurationistypicallyperformedbyanexperiencedtechnician,afterfixtureshavebeeninstalled.Theinteractivemethodcansavetime,sinceyouconnectandtestyourfixturesonlyonce.

100 – 240 VAC

100 – 240 VAC

ControllerKeypad iPlayer 3

Controller

Data Enabler Pro

Serial Cable

DMX Data

JunctionBox

Data Enabler Pro

DMX installation with iPlayer 3 DMX-based installations typically feature multiple series of ColorGraze Powercore fixtures controlled by a DMX controller such as iPlayer 3. Data Enabler Pro devices are connected in series, then connected to an output port on the iPlayer 3. ColorGraze Powercore fixtures can be installed end-to-end or spaced apart to support virtually any lighting design.

Light System Manager Controller

100 – 240 VAC

EthernetController

Keypad EthernetSwitch

CAT 5e Cable

CAT 5e Cable

Ethernet Data

JunctionBox

Data Enabler Pro

Data Enabler Pro

Ethernet installation with Light System Manager Large-scale, Ethernet-based installations can include dozens or hundreds of series of ColorGraze Powercore fixtures connected to Light System Manager via Data Enabler Pro devices and other Ethernet hardware.


Center Beam fc Beam Width

4.0 ft

8.0 ft

12.0 ft

16.0 ft

20.0 ft

24.0 ft

151 fc

38 fc

17 fc

9 fc

6 fc

4 fc

0.7 ft

1,4 ft

2.1 ft

2.8 ft

3.5 ft

4.1 ft

5.5 ft

11.1 ft

16.6 ft

22.1 ft

27.6 ft

33.2 ft

�� Vert. Spread: 9.9º�� Horiz. Spread: 69.3º

Illuminance at DistanceColorGraze Powercore2 ft (610 mm), 10º x 60º beam angle Cd: 0

417

833

1,250

1,667

2,083

2,500VA: 0º 10º 20º 30º 40º

90º

80º

70º

60º

50º

� - 0º H � - 90º H

Candela Table

0.0 22.5 45.0 67.5 90.0 0 2408 2408 2408 2408 2408 5 1185 1284 1605 2118 2397 15 154 171 266 885 2297 25 68 78 114 278 1900 35 39 44 66 128 1174 45 19 23 39 78 449 55 8 11 22 46 115 65 4 4 11 23 42 75 3 2 4 9 16 85 1 1 1 2 2 90 1 1 1 1 0

Polar Candela Distribution

Effective Floor Cavity Reflectance: 20% RC 80 70 50 30 10 0 RW 70 50 30 10 70 50 30 10 50 30 10 50 30 10 50 30 10 0 0 119119119119 116116116116 111111111 106106106 102102102 100 1 113110107105 111108106103 104102100 100 99 97 97 96 94 93 2 107102 98 94 105100 96 93 97 94 91 94 91 89 91 89 87 85 3 101 95 89 85 99 93 88 85 91 87 83 88 85 82 86 83 81 79 4 96 88 83 78 94 87 82 78 85 80 77 83 79 76 81 78 75 73 5 91 83 77 72 90 82 76 72 80 75 71 78 74 71 77 73 70 68 6 87 78 72 67 85 77 71 67 75 70 66 74 69 66 73 69 66 64 7 83 73 67 63 81 73 67 63 71 66 62 70 65 62 69 65 62 60 8 79 69 63 59 78 69 63 59 68 62 59 67 62 58 66 61 58 57 9 75 66 60 56 74 65 60 56 64 59 56 63 59 55 63 58 55 54 10 72 63 57 53 71 62 57 53 61 56 53 61 56 53 60 56 52 51

Coefficients Of Utilization - Zonal Cavity MethodZonal Lumen Summary

ZONE LUMENS %FIXT 0- 30 485 64.9 0- 40 617 82.5 0- 60 723 96.8 0- 90 747 100.0 90-120 0 0.0 90-130 0 0.0 90-150 0 0.0 90-180 0 0.0 0-180 748 100.0

Zonal Lumen

PhotometricsPhotometricdataisbasedontestresultsfromanindependentNISTtraceabletestinglab. IES data is available at www.philipscolorkinetics.com/support/ies.

ColorGraze Powercore2 ft (610 mm), 30º x 60º beam angle

For lux multiply fc by 10.7

LED Lumens EfficacyRGB 748 16.7

LED Lumens EfficacyRGB 736 16.1

49 ft (14.9 m) 1 fc maximum distance

Center Beam fc Beam Width

4.0 ft

8.0 ft

12.0 ft

16.0 ft

20.0 ft

24.0 ft

73 fc

18 fc

8 fc

5 fc

3 fc

2 fc

2.0 ft

3.9 ft

5.9 ft

7.8 ft

9.8 ft

11.7 ft

5.0 ft

10.0 ft

15.0 ft

20.1 ft

25.1 ft

30.1 ft

�� Vert. Spread: 27.5º�� Horiz. Spread: 64.2º

Illuminance at DistanceCd: 0

200

400

600

800

1,000

1,200VA: 0º 10º 20º 30º 40º

90º

80º

70º

60º

50º

� - 0º H � - 90º H

Candela Table

0.0 22.5 45.0 67.5 90.0 0 1174 1174 1174 1174 1174 5 1079 1088 1118 1146 1160 15 515 565 721 936 1048 25 156 184 304 586 806 35 62 70 109 275 497 45 35 38 52 110 239 55 20 22 30 49 96 65 11 11 15 24 37 75 5 5 6 10 12 85 2 1 1 1 1 90 1 1 1 0 0

Polar Candela Distribution

Effective Floor Cavity Reflectance: 20%

RC 80 70 50 30 10 0 RW 70 50 30 10 70 50 30 10 50 30 10 50 30 10 50 30 10 0 0 119119119119 116116116116 111111111 106106106 102102102 100 1 113110107105 110108105103 104102100 100 98 97 96 95 94 92 2 107101 97 93 105100 96 92 96 93 90 93 91 88 91 88 87 85 3 101 94 89 84 99 93 88 84 90 86 82 88 84 81 85 82 80 78 4 96 88 82 77 94 86 81 77 84 80 76 82 78 75 80 77 74 72 5 91 82 76 71 89 81 75 71 79 74 70 77 73 70 76 72 69 67 6 86 77 70 66 85 76 70 66 74 69 65 73 68 65 72 68 64 63 7 82 72 66 62 80 72 66 61 70 65 61 69 64 61 68 64 60 59 8 78 68 62 58 77 68 62 58 66 61 57 65 61 57 64 60 57 55 9 74 65 58 54 73 64 58 54 63 58 54 62 57 54 61 57 54 52 10 71 61 55 51 70 61 55 51 60 55 51 59 54 51 58 54 51 50

Coefficients Of Utilization - Zonal Cavity MethodZonal Lumen Summary

ZONE LUMENS %FIXT 0- 30 488 66.3 0- 40 605 82.1 0- 60 708 96.1 0- 90 736 100.0 90-120 0 0.0 90-130 0 0.0 90-150 0 0.0 90-180 0 0.0 0-180 736 100.0

Zonal Lumen

34.3 ft (10.5 m) 1 fc maximum distance


SpecificationsDue to continuous improvements and innovations, specifications may change without notice.

Item Specification 1 ft (305 mm) 2 ft (610 mm) 3 ft (914 mm) 4 ft (1219 mm)

Output

Beam Angle 10° x 60° / 30° x 60°

Lumens* 374 (10° x 60°)368(30° x 60°)

748(10° x 60°)736 (30° x 60°)

1122 (10° x 60°) 1104 (30° x 60°)

1496 (10° x 60°) 1472 (30° x 60°)

LED Channels Red / Green / Blue

Mixing Distance 6 in (152 mm) to uniform beam saturation

Lumen Maintenance† 100,000 hours L50 @ 25° C 90,000 hours L50 @ 50° C

Electrical

InputVoltage 100–240VAC,auto-switching,50/60Hz

Power Consumption18Wmaximum at full output, steady state

35 W maximum at full output, steady state

52.5 W maximum at full output, steady state

70 W maximum at full output, steady state

ControlInterface Data Enabler Pro (DMX or Ethernet)

Fixturefirmwareaddressable8-or16-bitcontrol

Control System Philips full range of controllers, including Light System Manager, iPlayer 3, and ColorDial Pro, or third-party controllers

Physical

Dimensions (Height x Width x Depth)

2.7x12x2.8in (69 x 305 x 71 mm)

2.7x24x2.8in (69 x 610 x 71 mm)

2.7x36x2.8in (69 x 914 x 71 mm)

2.7x48x2.8in (69 x 1219 x 71 mm)

Weight 2.8lb(1.3 kg) 4.9 lb (2.2 kg) 8.1lb(3.6 kg) 10.8lb(4.9 kg)

Housing Extruded anodized aluminum

Lens Clear polycarbonate

Fixture Connectors Integral male / female waterproof connectors

Mounting Multi-positional,constanttorque,lockinghinges

Temperature-40° – 122° F (-40° – 50°C)Operating -4° – 122° F (-20° – 50° C) Startup -40°–176°F(-40°–80°C)Storage

Humidity 0–95%,non-condensing

Maximum Fixture Run Lengths†

37@100VAC43@120VAC56@220–240VAC

Configuration: 2 ft (610 mm) fixtures installed end-to-end, 20 A circuit, standard 50 ft (15.2 m) Leader Cable

Certificationand Safety

Certification UL / cUL, FCC Class A, CE, PSE, CCC

Environment Dry / Damp / Wet Location, IP66

10° 30° 60°

10° 30° 60°

E To calculate the number of fixtures your specific installation can support, download the Configuration Calculator from www.philipscolorkinetics.com/support/install_tool/

2.1 in(53 mm)

24 in (609 mm) / 36 in (914 mm) / 48 in (1219 mm)

17.4 in (442 mm) / 29.4 in (747 mm) / 41.4 in (1052 mm)

2.8 in(71 mm)

3.4 in(85 mm)

2.7 in(69 mm)

3.4 in(85 mm)

2.36 in(60 mm)

.38 in(9.5 mm)

1.38 in(35 mm)

.88 in(22 mm)

.38 in(9.5 mm)

.813 in(21 mm)

1.75 in(44 mm)

2.25 in(57 mm)

1.94 in(49 mm) 1.4 in

(39 mm)

.28 in (7.2 mm) x4Substrate

3.16 in(80 mm)

1.38 in(35 mm).88 in

(22 mm)

.38 in(9.5 mm) 2.36 in

(60 mm)

.22 in (5.5 mm) x6Fixture

12 in (305 mm)

*MeasurementscomplywithIESLM-79-08testingprocedures.† L50=50%lumenmaintenance(whenlightoutputdropsbelow50%ofinitialoutput).Ambientluminairetemperaturesspecified.Lumenmaintenancecalculationsarebased on lifetime prediction graphs supplied by LED source manufacturers. Calculations for white-light LEDfixturesarebasedonmeasurementsthatcomplywithIESLM-80-08testingprocedures.Refertowww.philipscolorkinetics.com/support/appnotes/lm-80-08.pdfformoreinformation.

‡Thesefigures,providedasaguideline,areaccurateforthisconfigurationonly.Changingtheconfigurationcan affect the fixture run lengths.


Item Type Size Item Number Philips 12NC

ColorGraze Powercore

10° x 60° beam angle

1 ft (305 mm) 123-000030-07 910503700880

ColorGrazePowercorefixtures

2 ft (610 mm) 123-000030-00 910503700308

3 ft (914 mm) 123-000030-01 910503700309

4 ft (1219 mm) 123-000030-02 910503700310


1 ft (305 mm) 123-000030-09 910503700882

2 ft (610 mm) 123-000030-03 910503700311

3 ft (914 mm) 123-000030-04 910503700312

4 ft (1219 mm) 123-000030-05 910503700313

ColorGraze Powercore Conduit

(UL / cUL only)


2 ft (610 mm) 123-000020-06 910503701833

3 ft (914 mm) 123-000020-11 910503701838

4 ft (1219 mm) 123-000020-16 910503701843


2 ft (610 mm) 123-000020-08 910503701835

3 ft (914 mm) 123-000020-13 910503701840

4 ft (1219 mm) 123-000020-18 910503701845

LeaderCablewithTerminatorUL / cUL 50 ft (15.2 m) 108-000042-00 910503700322

CE / PSE 50 ft (15.2 m) 108-000042-01 910503700323

Depending on the installation’s design, youmayneedJumperCablestoaddspacebetweenfixtures Jumper Cable

UL / cUL

End-to-End 108-000039-00 910503700314

1 ft (305 mm) 108-000039-01 910503700315

5 ft (1.5 m) 108-000039-02 910503700316

CE / PSE

End-to-End 108-000040-00 910503700317

1 ft (305 mm) 108-000040-01 910503700318

5 ft (1.5 m) 108-000040-02 910503700319

Glare Shield

1 ft (305 mm) 120-000081-00 910503700745

2 ft (610 mm) 120-000081-01 910503700746

3 ft (914 mm) 120-000081-02 910503700747

4 ft (1.2 m) 120-000081-03 910503700748

AdditionalTerminators Quantity 10 120-000074-00 910503700580

AdditionalHinge Quantity 1 120-000098-00 910503700772

Data Enabler Pro

3/4in/1/2inNPT (U.S. trade size conduit) 106-000004-00 910503701210

PG21 / PG13 (metric size conduit) 106-000004-01 910503701211

Use Item Number when ordering in North America

Fixtures and AccessoriesColorGraze Powercore fixtures are part of a complete system which includes:

• OneormoreDataEnablerProdevices

• AnyPhilipscontroller,includingLightSystemManager,iPlayer3,andColorDialPro, or a third-party controller

• Forstandardfixtures,LeaderCablestoconnectthefirstfixtureineachseriestoaData Enabler Pro

• Forstandardfixtures,optionalJumperCablestoaddspacebetweenfixturesinaseries, if necessary

• 4-conductorcopperwiretoconnecteachDataEnablerProtoacommonjunctionbox,ifinstallingfixturesinparallel,andtoconnectColorGrazePowercoreConduitfixturesinseries.Standard12AWG(2.05mm)strandedwireisrecommended.

Custom Configurations

Component AvailableNon-StandardOptionsColor Temperature

2700K, 3000 K, 3500 K, 4000 K, 5500 K, 6000 K, 6500 K

Color Royal Blue, Blue, Green, Amber, RedBeam Angle 9° x 9°, 15° x 30°, 60° x 30°, 90° x 60°

In addition to the standard configurations listed here, custom configurations are also available with non-standard options. SeetheColorGrazePowercoreOrderingInformationsheetat www.philipscolorkinetics.com/ls/rgb/graze/ for complete details.

3.1 in79 mm

.4 in10 mm


InstallationColorGraze Powercore offers vibrant grazing and wall-washing light. Powercore technology, which integrates LED power and data management within the fixture, eases installation by eliminating the need for external power supplies.

Owner / User Responsibilities It is the responsibility of the contractor, installer, purchaser, owner, and user to install, maintain, and operate ColorGraze Powercore fixtures in such a manner as to comply with all applicable codes, state and local laws, ordinances, and regulations. Consult with the appropriate electrical inspector to ensure compliance.

Installing in Damp or Wet LocationsWheninstallinginwetordamplocations,sealallDataEnablerProdevicesandjunctionboxeswithelectronics-gradeRTVsiliconesealantsothatwaterormoisturecannotenteror accumulate in wiring compartments, cables, or other electrical parts. Use suitable outdoor-ratedjunctionboxeswheninstallingindamporwetlocations.Additionally,usegaskets,clamps,andotherpartsrequiredforinstallationtocomplywithallapplicablelocal and national codes.

Prepare for the Installation1. Refer to the lighting design plan, architectural diagram, or other diagram that

shows the physical layout of the installation to identify the locations of all switches, controllers.DataEnablerProdevices,fixtures,andcables.

ColorGrazePowercorefixturescanbeinstalledinseriesorinparallel(wiredtoacommonjunctionbox).ThemaximumnumberoffixtureseachDataEnablerProcansupportdependsonspecificconfigurationdetailssuchasfixturelength,fixturespacing,circuit size, line voltage, and leader cable length. As an example, the table to the right liststhemaximumnumberoffixturesinasinglerunatvariousvoltages,assuming2ft(610mm)fixturesinstalledend-to-endona20Acircuit,usingastandard50ft(15.2m)LeaderCable.Thesefigures,providedasaguideline,areaccurateforthespecifiedconfigurationonly.Changingtheconfigurationcanaffectthefixturerunlengths.

Inadditiontomaximumfixturerunlengthsdeterminedbytheelectricalconfiguration,eachDataEnablerProimposesmaximumrunlengthsbasedondataintegrity.Toensure data integrity, maximum individual run lengths should not exceed 175 ft (53.3 m), and the total cable length per Data Enabler Pro should not exceed 400 ft (122 m).

•

ColorGrazePowercoreConduitfixturescanbeconnectedinarunusingthefixtures’6ft(1.2m)4-conductorflyingleadsandjunctionboxes.Ensurethatalljunctionboxesare suitable for the environment and sealed if necessary, and that all wiring between junctionboxescomplieswithlocalcodes.

37@110VAC43@120VAC56@220–240VAC

Fixture run lengths

Assuming 2 ft (610 mm) fixtures installed end-to-end on a 20 A circuit, using a standard 50 ft (15.2 m) Leader Cable

Fixtures

Fixtures

Data Enabler Pro

Data Enabler Pro

Fixtures

Fixtures

Data Enabler Pro

Data Enabler Pro

DataIntegrity—maximumindividuallength175ft(53.3m)

DataIntegrity—totallength400ft(122m)

E Refer to the ColorGraze Powercore Installation Instructions for specific warning and caution statements.

E For help calculating the number of fixtures your specific installation can support, download the Configuration Calculator from www.philipscolorkinetics.com/support/install_tool/, or consult Application Engineering Services at [email protected].

E Clean the lens with water and mild detergent using a soft cleaning cloth, and wipe dry. Because they will scratch, soften, pit, haze, yellow, mar, or crack the lens, do not use paper towels, abrasive cleaning products, window cleaners, or cleaning solutions containing chemicals such as ammonia, sodium hydroxide, and isopropyl alcohol.


Start the Installation1. Install all Data Enabler Pro devices, including any interfaces with controllers. Data

Enabler Pro devices and external controllers send power and control signals to thefixturesoverasinglefixturecable.Additionalcablingmayberequiredtoconnectfixturestogetherinparallelorinseries.

2. Verifythatalladditionalsupportingequipment(switches,controllers)isinplace.

3. Ensure that all additional parts and tools are available, including:

• Theincludedmountinghingesandhardware

• 2mm,2.5mm,and4mmhexkeywrenches

• 1/4in(5mm)socketcapfasteners,anchors,orscrewsforsurfacemounting

• Conduit,asneeded

• 4-conductorcopperwire,asneeded.Standard12AWG(2.05mm)strandedwire is recommended.

• Junctionboxes,asneeded,ratedforyourapplication.(Refertothemanufacturer’sliteratureforadditionalitemsrequiredformountingorsealing.)

• Electronics-graderoomtemperaturevulcanizing(RTV)siliconesealant,asneeded

Unpack and Prepare Fixtures 1. Carefully inspect the box containing ColorGraze Powercore and the contents for

any damage that may have occurred in transit.

2. ColorGrazePowercorefixturesareaddressablein1ft(305mm)segments.Thisfeatureallowsplaybackcontrollerstosenduniquelightoutputdatatoeachsegmentofeachfixturewithinyourinstallation.

Eachfixturesegment,orLEDnode,comepre-programmedwithauniqueserialnumber.Eachfixturehastwo,three,orfourserialnumbers,dependingonitslength.Asyouunpackthefixtures,recordtheserialnumbersinalayoutgrid(typically a spreadsheet or list) for easy reference and light addressing.

3. Assigneachfixturetoapositioninthelightingdesignplan.

4. Tostreamlineinstallationandaidinlightaddressprogramming,youcanaffixaweatherproof label identifying the order or placement in the installation to an inconspicuouslocationoneachfixture’shousing.

Included in the boxColorGrazePowercorefixture(1) or (2) Mounting hinges(2) or (4) M5, 15 mm stainless steel hex bolts for hinge installationInstallation Instructions

Record fixture Serial Numbers

E Refer to the Data Enabler Pro Installation Instructions or Product Guide for guidelines on configuring and positioning the Data Enabler Pro in relation to the controller.


.40 in(10.2 mm)

1.88 in(48 mm)

.91 in(23 mm)

14 AWG.07 in (1.85 mm)

.58 in(14.8 mm)

1.88 in(48 mm)

.91 in(23 mm)

12 AWG.08 in (2 mm)

UL / cUL

CE / PSE / CCC

.40 in(10.2 mm)

1.88 in(48 mm)

.91 in(23 mm)

14 AWG.07 in (1.85 mm)

.58 in(14.8 mm)

1.88 in(48 mm)

.91 in(23 mm)

12 AWG.08 in (2 mm)

UL / cUL

CE / PSE / CCC

Leader Cable Connector Dimensions

115°

3.937 in (100 mm)Swing radius

1.16 in (29 mm)

110°



1.16 in (29 mm)

68°

Jumper Cable End-to-End

Leader Cable 50 ft (15.2 m)

Jumper Cable 1 ft (305 m)

or 5 ft (1.5 m)

Terminator

C

Data EnablerPro

ColorGraze Powercore fixtures

2.1 in(53 mm)

24 in (609 mm) / 36 in (914 mm) / 48 in (1219 mm)

17.4 in (442 mm) / 29.4 in (747 mm) / 41.4 in (1052 mm)

2.8 in(71 mm)

3.4 in(85 mm)

2.7 in(69 mm)

3.4 in(85 mm)

2.36 in(60 mm)

.38 in(9.5 mm)

1.38 in(35 mm)

.88 in(22 mm)

.38 in(9.5 mm)

.813 in(21 mm)

1.75 in(44 mm)

2.25 in(57 mm)

1.94 in(49 mm) 1.4 in

(39 mm)

.28 in (7.2 mm) x4Substrate

3.16 in(80 mm)

1.38 in(35 mm).88 in

(22 mm)

.38 in(9.5 mm) 2.36 in

(60 mm)

.22 in (5.5 mm) x6Fixture

12 in (305 mm)

Mount and Connect FixturesMakesurethepowerisOFFbeforemountingandconnectingColorGrazePowercorefixtures.

Standard ColorGraze Powercore fixtures offer bulkhead connectors that accept the ColorGraze Powercore pre-configured Leader and Jumper Cables. Because they have a male connector on one end of the fixture and a female connector on the other end, ColorGraze Powercore fixtures are directional, and must all be oriented in the same direction.

Use ColorGraze Powercore Conduit in installations where local electrical codes requireyoutorunconduittothefixtures.ColorGrazePowercoreConduitfixtureshavethreadedopeningsthataccept1/2inNPTconduit.Becausebothendsarethesame, ColorGraze Powercore Conduit fixtures can be oriented in either direction.

Mount Fixtures

1. Usingtheincluded4mmhexhardware,attachtwohingestoeachfixture.Therearethreepossiblemethodsforattachinghingestothefixtures,eachmethodofferingdifferingdegreesofswingradiusandspace-efficiency.Selectthemethodmost suitable for your application.

2. IfinstallingColorGrazePowerConduitfixtures,orColorGrazePowercorefixturesinparallel,mountjunctionboxesinaccordancewiththelightingdesignplan.

ColorGrazePowercoreConduitfixturesrequireajunctionboxtomakeconnectionsbetweeneachpairoffixturesinaseries.Eachendofthefixturehasintegrated6ft(1.8m)flyingleadsoneachendforjunctionboxconnections.

3. When installing a linear series of ColorGraze Powercore fixtures, make sure that allfixturesareorientedinthesamedirection.TheLeaderCableconnectstothemale bulkhead connector on the first fixture in each series.


Because both ends of the fixture are the same, ColorGraze Powercore Conduit fixtures can be oriented in either direction.

Using1/4in(5mm)socketcapscrews,bolts,oranchors,mountthefixtureswith hinge assemblies directly to a wall or other mounting surface. Make sure the mountingsurfaceisflat,suitableforthemountinghardware,andclearofdebrisand other obstructions.

4. Rotatethefixturehingeassembliesintothedesiredpositions.Forconsistentposition control, use the indicators on the side of each hinge knuckle for reference. Use a 2 mm hex key wrench to loosen the set screws, as needed.

5. Toaccommodateinstallationfromvariousangles,eachhingehasfoursetscrewsdesigned to lock the hinge position. All four, or only two, of the set screws may be used, depending on the mounting method and swing radius you select for the hinge. For example, if the hinge leaves are to be fully closed, the interior set screws may not be accessible.

Do not lock the hinges positions at this time; the hinges have a built-in constant torquefeaturethatallowstemporarypositioning.Foroptimallightoutputperformance, aim and lock the hinges following installation.

Make Cable Connections (ColorGraze Powercore)

1. Ifinstallingfixturesinseries,runa50ft(15.2m)LeaderCablefromaDataEnablerProdevicetothefirstfixtureintheseries.Twisttheconnectorendstolock the Leader Cable into place.

2. Ifinstallingfixturesinparallel,run4-conductorcopperwirefromaDataEnablerProdevicetoacommonjunctionbox.

Run50ft(15.2m)LeaderCablesfromthecommonjunctionboxtothefirstfixtureineachseries.TwisttheconnectorendstolocktheLeaderCablesintoplace.

Withinthecommonjunctionbox,usewirenutstoconnectline,neutral,ground,anddatawires.Tuckwireconnectionsintothejunctionbox.

Securealljunctionboxcovers.Ifinstallinginadamporwetlocation,sealalljunctionboxesandpointsofentrywithcontractor-gradeRTVsiliconesealant.Usegaskets,clamps,andotherpartsandfittingsrequiredtocomplywith local outdoor wiring codes.

3.ConnectallJumperCablesbetweenfixtures.Twisttheconnector ends to lock.

4.Attachtheterminatortothelastfixtureineachseries.TerminatorsareprovidedwiththeColorGrazePowercore Leader Cables.

.125 in (3 mm) Minimum

115°


1.16 in (29 mm)

110°



1.16 in (29 mm)

68°

ColorGraze Powercore Conduit fixtures

Junction boxfor connecting

6ft(1.8m)fixture flying leads

Junction boxfor termination

Data EnablerPro

Junction boxfor connecting

6ft(1.8m)fixture flying leads

Fixture flying leads

Minimum distance between fixtures


Make Cable Connections (ColorGraze Powercore Conduit)

1. Ifinstallingfixturesinseries,run1/2inNPTconduitand4-conductorcopperwirefromaDataEnablerProdevicetothefirstfixtureintheseries.Usewirenutstoconnectline,neutral,ground,anddatawirestothefixture’sflyingleads.

2. Ifinstallingfixturesinparallel,run1/2inNPTconduitand4-conductorcopperwirefromaDataEnablerProdevicetoacommonjunctionbox.

Runtheintegrated6ft(1.2m)4-conductorflyingleadsand1/2inNPTconduitfromthethefirstfixtureineachseriestotjecommonjunctionbox.Withinthecommonjunctionbox,usewirenutstoconnectline,neutral,ground,anddatawires.Tuckwireconnectionsintothejunctionbox.

3. TomakeconnectionsbetweenColorGrazePowercoreConduitfixturesinaseries,runtheintegrated6ft(1.2m)4-conductorflyingleadsand1/2inNPTconduitfromtheoutputendofonefixtureandinputendofthenextfixtureintheseriestoajunctionbox.Withinthejunctionboxes,usewirenutstoconnectline,neutral,ground,anddatawires.Tuckwireconnectionsintothejunctionbox.

4. Terminatetherunbyrunning1/2inNPTconduitandtheflyingleadsfromtheoutputendofthelastColorGrazePowercoreConduitfixtureintheseriestoajunctionbox.Withinthejunctionbox,usewirenutstoconnectline,neutral,ground,anddatawires.Tuckwireconnectionsintothejunctionbox.

5. Securealljunctionboxcovers.Ifinstallinginadamporwetlocation,sealalljunctionboxesandpointsofentrywithcontractor-gradeRTVsiliconesealant.Usegaskets,clamps,andotherpartsandfittingsrequiredtocomplywithlocaloutdoor wiring codes.


Make Power ConnectionsOnceyou’vemadeallfixtureandjunctionboxconnections,connecttheflyingleadsfromaLeaderCable,4-conductorwirefromacommonjunctionbox,orthecablefrom the input end of the first ColorGraze Powercore Conduit fixture in a series to the fixture cable 4-wire PC terminal connector block inside the Data Enabler Pro Housing.

Address the FixturesMakesurethepowerisONbeforeaddressingandconfiguringfixtures.

Toallowafinelevelofcontrol,ColorGrazePowercorefixturesareaddressablein1ft (305 mm) segments, or nodes. ColorGraze Powercore fixtures have two, three, or fournodes,dependingonfixturelength,eachidentifiedbyauniqueserialnumber.

ColorGrazePowercorefixturesoperatein8-bitmodebydefault.YoucanconfigureColorGraze Powercore to operate in 16-bit mode, which increases fixture resolution for smoother dimming.

In8-bitmode,fixturesuseoneDMXaddressperLEDchannel(red,green,andblue).In16-bitmode,fixturesusetwoDMXaddressesperLEDchannel.ThefirstDMX address corresponds to the “coarse” data for that channel, and the second corresponds to the “fine” data. By using double the number of DMX addresses, 16-bit mode increases fixture resolution from 256 dimming steps to 65,536 (256 x 256) dimming steps.

Each 1 ft (305 mm) ColorGraze Powercore node comes factory-addressed with a starting DMX address of 1. For lighting designs where fixture nodes work in unison, all nodes can be assigned the same DMX addresses. Changes to the default addresses are not necessary, but if nodes were previously readdressed for use in other installations, you must reset them. For light show designs that show different colors ondifferentnodes,youmustassignuniqueDMXaddressestoyournodesandsortthem in a useful order.

Power / data output to fixtures

Mains voltage output

L N

L N

DMX

DMX

UL / cUL

UL / cUL

LN

CE / PSE

CE / PSE UL / cULCE / CQC

LN

UL / cUL CE / PSEL

NL

N

L N

L N L N

L N

UL / cUL CE / PSE

L N L N

UL / cUL CE / PSE

L N L N

L N

CE / PSE

L N

CE / CCC

L N

CE / Japan

L N

CE / PSE

L N

UL / cUL

UL / cUL

LN

CE / PSE

CE / PSE UL / cULCE / CQC

LN

UL / cUL CE / PSEL

NL

N

L N

L N L N

L N

UL / cUL CE / PSE

L N L N

UL / cUL CE / PSE

L N L N

L N

CE / PSE

L N

CE / CCC

L N

CE / Japan

L N

CE / PSE

L N

E Refer to the Data Enabler Pro Product Guide for comprehensive installation and configuration instructions. You can view or download the guide from www.colorkinetics.com/ls/pds/dataenablerpro

Data Enabler Pro

DMX Channel Assignments

8-BitMode1 2 3

Red Green Blue

16-Bit Mode1 2 3 4 5 6

Red Coarse Red Fine Green Coarse Green Fine Blue Coarse Blue Fine

E You can address fixtures and switch between 8-bit mode and 16-bit mode using QuickPlay Pro. You can download QuickPlay Pro from www.colorkinetics.com/support/addressing/


• InEthernetinstallations,youcanaddressandconfigurefixturenodesusingQuickPlay Pro with a computer connected to your lighting installation’s network. QuickPlayProcanautomaticallydiscoverallfixturenodes,controllers,andDataEnablerProdevicesforquickconfiguration.

• InDMXinstallations,youcanaddressandconfigurefixturenodesusingQuickPlayProwithiPlayer3orSmartJackPro.Youcanmanuallyenterfixturenodeserialnumbers,oryoucanimportaspreadsheetlistingeachfixturenode’sserialnumber and starting DMX address.

For details on addressing and configuring fixtures, controllers, and power / data supplies with QuickPlay Pro, refer to the Addressing and Configuration Guide, which you can view or download at www.philipscolorkinetics.com/support/addressing.

Aim and Lock the FixturesMakesurepowerisONbeforeaimingfixtures. Rotatethefixturestoachievetheoptimalangleforlightoutput.Forconsistentposition control, use the indicators on the side of each hinge knuckle as reference.

Forfinehorizontaladjustment,youcanchangethepositionofthehingemounting block located on the side of each fixture. Loosen the set screw with a 2.5 mm hex key, slide the mounting block to the desired position, then tighten the set screw.

Oncesatisfiedwithfixtureanglesandpositioning,usea 2 mm hex key wrench to tighten the hinge position set screws and lock each hinge.

Attach Glare Shields (Optional)Glare Shields, in 1 ft (305 mm), 2 ft (610 mm), 3 ft (914 mm), and 4 ft (1.2 m) lengths, can be inserted in the grooves in the ColorGraze Powercore housing. Glare Shields block unwanted spill light, and can shield the light sources from being directly visible in certain mounting situations.

1. Insert the Glare Shield’s triangular tab in the outer groove on the side of the ColorGraze Powercore housing.

2. Using a hex wrench, tighten the locking screws to hold the Glare Shield in place.

3. (Optional)AttachatethertotheknockoutintheGlareShield,andaffixthetether to a secure anchor point.

E You can download QuickPlay Pro from www.colorkinetics.com/support/addressing.

E You will need the layout grid that you created when you recorded the serial numbers of the light fixtures in your installation.

E Do not look directly into a fixture when aiming and locking.

E The hinge position set screws have factory applied thread lock. Confirm the fixture angle and positioning before locking each hinge.


2. Using a small screwdriver, hand-tighten all set screws. Using a 1.5 mm hex wrench,torquethesetscrewstoapproximately3.5in-lbs(4kgf/cm)tohold the Glare Shield in place.

3. (Optional)AttachatethertotheknockoutintheGlareShield,andaffixthe tether to a secure anchor point.

1.5 mm

Philips Color Kinetics3 Burlington Woods DriveBurlington, Massachusetts 01803 USATel 888.385.5472Tel 617.423.9999Fax 617.423.9998www.philipscolorkinetics.com

Copyright © 2008 – 2012 Philips Solid-State Lighting Solutions, Inc. All rights reserved. Chromacore, Chromasic, CK, the CK logo, Color Kinetics, the Color Kinetics logo, ColorBlast, ColorBlaze, ColorBurst, eW Fuse, ColorGraze, ColorPlay, ColorReach, iW Reach, eW Reach, DIMand, EssentialWhite, eW, iColor, iColor Cove, IntelliWhite, iW, iPlayer, Optibin, and Powercore are either registered trademarks or trademarks of Philips Solid-State Lighting Solutions, Inc. in the United States and / or other countries. All other brand or product names are trademarks or registered trademarks of their respective owners. Due to continuous improvements and innovations, specifications may change without notice. Cover Photo: Atlantic ocean residence, by John Brandon Miller DAS-000010-00 R08 05-12

ColorGraze Powercore · install, letting you focus on the visual impact of your lighting design...

Documents

Transcript of ColorGraze Powercore · install, letting you focus on the visual impact of your lighting design...