Color coding

download Color coding

of 6

  • date post

    31-Oct-2014
  • Category

    Documents

  • view

    111
  • download

    3

Embed Size (px)

description

Color coding

Transcript of Color coding

Attachment 2- Color Coding and LabelingThe nature of the pipe contents shall be identified by means of a Three Band Colour Code Identification Band System , colors are as specified in Norsok DP-002 The outer bands, which will be the same color, are the Basic/Primary Identification Bands (PIB) and the middle band is the Safety/ Secondary Identification Band (SIB). The arrangement is shown in Figure 1.

Identification & Size The width requirements for the PIBs and SIB shall be the same for all pipe sizes over 6 diameter, with narrower band widths being used for pipe sizes varying from 2 to 6 diameter. The dimensions shall be as follows Table -1 Table -1

Pipe Diameter 2 to 6 inclusive Greater than 6

Each Basic/Primary Band 75 mm 150 mm

Safety/Secondary Band 50 mm 100 mm

Colour Coding Bands shall be provided on both sides of and adjacent to valves, tees, important fittings, wall entries and overpasses and outboard of flanges to and from equipment such as vessels, tanks, exchangers, compressors and pumps

Colour coding bands shall be provided at uniform intervals, not less than 30m and not more than 50m depending on the complexity and pipe run lengths, along horizontal and up vertical sections of pipework and at all feed points. Where multiple lines run close to each other, such as in common pipe racks, the line numbers and flow direction shall be located directly in line with one another at positions that are readily visible. For Valves, the full valve body shall be painted with the SIB for the relevant fluid group. The full Color code shall be applied both sides of the valve, to the adjacent pipework. For Control Valves, the valve bonnet and actuator or hand wheel /lever, shall be painted with one of the following two colours, to indicate whether the Control Valve is designed to fail open or fail closed as shown in figure 2 Fail Open Control Valves shall be painted Green, Fail Closed Control Valves shall be painted Red,

Content Labeling and Safety Warning Signs The additional use of Colored Labels giving the full or abbreviated product description, temperature, pressure, and other details necessary to identify any potential hazard, together with the appropriate visual aids and hazard pictorial symbols, is to be encouraged. Such labels and markings shall not, however, be considered as a substitute for the Color coding, whose application is considered mandatory. Where applied, labels shall be brief and informative and written in English. The text size for different pipe diameters shall be as specified in Table -2 The background colour of the label shall be similar to that of the appropriate PIB, ideally with appropriate SIB contrasting text colour,. The length of the labels shall vary from 200 to 800mm and they shall be applied adjacent to the CCIB locations. Labeling shall be in the form of painting or self-adhesive plastic labels. Plastic labels shall be of high performance type suitable for marine environment. Line Numbering In addition to being Colour Coded, each pipe system, pipeline and valve shall be individually identified by marking them in accordance with the BW Equipment Identification and Tag Numbering System, The required identification markings relate to pipe size, service, design, area code and ownership code. All characters used shall be in upper case. No separators, hyphens, punctuation marks or spaces are allowed. The line number and the flow direction shall be stenciled on each pipe section and pipeline together with the CCIB, to provide the pipework with unique traceability. The identification markings shall be stenciled on the pipe a distance of approximately 400 mm from the edge of the outer colour band. Letter size shall be equal to half of the pipe diameter for pipe between 2 and 12 diameter, with a minimum height of 1 for smaller pipe sizes and a maximum height of 6 for larger pipe sizes. Line identification markings shall be stenciled in black directly onto the light grey/white decorative background. Table -2 Size of Lettering Pipe Diameter 2 to 6 inclusive 6 to 50 inclusive Greater than 50 Width x Height 30 x 30mm 80 x 80mm 100 x 100mm 10 mm min. 25 mm min. 30 mm min. Spacing

Table -3 Shape and size of direction arrow shall be as follows: Pipe Diameter 2 to 6 inclusive 6 to 50 inclusive Greater than 50 10 40 50 W1(mm) 30 80 100 W2(mm) 45 90 150 L1(mm) 135 270 450 L2(mm)

Table 4 Colour Coding

Equipment Steelwork All Topsides Structural Steelwork Unless Otherwise Specified All Sub Structural Steelwork Tanks And Coated Exterior Wall Cladding Accommodation, Storerooms And Other Interior Living And Workroom Areas Firewalls (If Painted) Painted Floor Decks/Walkways Access/Escape Routes Overhead Obstructions Monorails/Hoists Handrails Ladder Cages Clean-Up Burner Piperacks Lifeboat Davits Gratings Pipe Supports HVAC Duct Conditioned Air Fresh Air Extract/Recirculated Air Exhaust Air Miscellaneous Crane Booms & l Cranes Lifeboats Tanks Caisson ESD Helideck (Perimeter of Landing Area, notations & markings, structural underside & walkways) Helideck Topside Lagging Walkways & Escape Routes Cladding (If Coated) Flare Tip Handling System Riser Turret Mooring Vessels Turbines, Pumps, Compressors Engines Heat Exchangers Air Compressors Minor Equipment Wellhead Fire Fighting Winches Control Valves Actuator Hand Lever and Wheel

Colour Description Grey Grey White Per Architectural Schedule White Grey Black With Yellow Stripes Yellow With Black Stripes Yellow Yellow Colour Of Structure Orange White White Brown Grey Red With Blue Bands Green Grey Brown With White Bands Orange Orange Light Colour White Orange White Green Aluminium Or Stainless Steel Jacket Unpainted. Colour Of Service Banded Only. Green with Yellow Strips on both sides White Yellow Yellow Off White Light Green Light Grey Off White Blue Light Grey Yellow Red Grey SIB Colour SIB Colour SIB Colour

Control Panels: Exterior Surfaces Interior Surfaces Plinths Electrical Equipment Exteriors: Switchgear, Lighting, Panels Etc. Transformers, Motors, Alternators Stainless Steel Terminal Boxes Pipe Piping Air Instrument Air Plant Chemical, Biocide Chemical, Catalyst Chemical, Scale Inhibitor Chemical, De-Mulsifier Or De-Foament Chemical, Surface Active Fluid Chemical, Glycol Chemical, Afff Corrosion Inhibitor Chemical, Oxygen Scavanger Chemical, Polyelectrolyte / Flokkulant Chemical, Sodium Hypochloryte Solution Wax Inhibitor Chemical, Glycol/Water ( Drain, Closed Drain, Mud Drain, Open Drain, Sewer/Sanitary Drain, Water/Storm Fuel, Jet Gas, Fire Fighting/Co2 Gas, Fuel Gas, Inert Gas, Waste/Flue Oil, Fuel (Diesel Oil) Oil, Hydraulic Oil, Lubricating Oil, Seal Process Blow Down Process Hydrocarbons Liquid Process Hydrocarbons Vapour Process Two Phase Produced Water Steam, Process Steam, Utility/Plant Vent, Atmospheric Vent, Flare Water, Sea Antiliquifaction Water, Sea, Ballast/Grout Water, Fresh/Glycol - Cooling Medium Water, Fresh, Potable Water, Sea, Fire Fighting Water, Grouting Systems Water, Fresh/Glycol - Heating Medium

Control Panels: Beige Semi Gloss White Gloss Black Semi Gloss Electrical Equipment Exteriors: Electrical Green Electrical Green Natural Finish Grey Colour up to 120 C, Aluminium above 120C Primary Secondary Identification Identification Band (PIB) Band(SIB) Light Blue White Light Blue White Violet Black Violet Violet Black Violet Black Violet Violet Orange Red Yellow Violet Violet Black Violet Black Violet Violet Black Violet Orange Black Blue Black Black Yellow Black Green Black Yellow Brown Violet Red Silver Gray Yellow Ochre White Yellow Ochre Silver Gray Yellow Ochre Brown Yellow Brown Blue Brown Brown Yellow Ochre Brown White Yellow Ochre Green Silver Silver Yellow Ochre Yellow Ochre Green Green Violet Green Red Green Violet Brown Brown Green Green Silver Gray Yellow Yellow Orange Blue White Yellow Orange

Water, Sea, Injection Water, Jet Water, Fresh, Raw Water, Fresh, Hot (Closed Circuit) Water, Sea RAL Equivalent for the Colours Colour Grey Black Yellow White Orange Blue Light Blue Green Electric Green Brown Silver Red Violet Yellow ochre Beige

Green Green Green Green Green

Yellow Yellow Green Violet White

RAL RAL 7001 RAL 9005 RAL 1021 RAL 9010 RAL 2003 RAL 5005 RAL 5012 RAL 6018 RAL 6037 RAL 8001 RAL 9006 RAL 3000 RAL 9010 RAL 1021 RAL 1001