COLD ROLLED SHEET PILES - escpilehk.com Bollard Catalogue.pdf · COLD ROLLED SHEET PILES 7...
Transcript of COLD ROLLED SHEET PILES - escpilehk.com Bollard Catalogue.pdf · COLD ROLLED SHEET PILES 7...
ESC Mooring Bollards
Marine mooring bollards provide a simple yet efficient method for
fulfilling mooring requirements to allow safe securing of vessels
next to jetties, wharves, berths and dolphins in ports and harbours.
ESC can offer a wide range of cast iron or steel bollards in various
sizes, grades and capacities.
ESC bollards are designed and manufactured in accordance to
various international standards such as BS 6349 pt 4 and PIANC
guidelines. Bollards are safety critical components and ESC strives
to provide bollards with superior service life and resistance to
physical and corrosive environments.
INTRODUCTION
ESC MOORING BOLLARDS
CLEAT
Section Rating (Tons)
10 15 20 25 30 35 50 75 80 100 150 200 250 300 70 5
T-Head
T-Horn
Kidney
Cleat
Double Bitt
Single Bitt
Pillar
T-Head Japanese Design
Pillar Japanese Design
T-HEAD T-HORN KIDNEY SINGLE BITT
PILLAR DOUBLE BITT T HEAD JAPANESE DESIGN PILLAR JAPANESE DESIGN
STANDARD RANGE
ESC offers a full range of Mooring Bollards
✓ Cast iron and steel bollards in a range of configurations.
✓ Up to 200 ton capacity
✓ Complete with anchoring sets
✓ Corrosion Protection Coating options—primer, epoxy coating,
galvanized, duplex (galvanized & painted)
✓ Fully customizable as bollards vary significantly between ports
and
countries.
STANDARD DESIGNS
TRICORN
COLD ROLLED SHEET PILES
3 ESC Mooring Bollards
ESC bollards are produced to the highest specifications.
The table gives indicative standards and grades but many
other options are available on request.
MATERIAL SPECIFICATION
BOLLARD SELECTION & LAYOUT
Bollards should be designed and laid out according to local standards. Some of the following aspects are to be considered in the design of the berth:
✓ Mooring patterns and line types, sizes and angles
✓ Changes in draft during loading/unloading of the vessel
✓ Wind and current forces
✓ Swell, wave and tidal forces
✓ Other abnormal environmental loadings
Mooring loads should be calculated where possible, but the following table can be used as an approximate guideline, also noting that if the berth is expected to experience adverse weather conditions, the bollard capacity should be increased by 25% or greater.
DISPLACEMENT APPROX. BOLLARD
RATING
Up to 2,000 tons 10 tons
2,000—10,000 tons 30 tons
10,000—20,000 tons 60 tons
20,000—50,000 tons 80 tons
50,000—100,000 tons 100 tons
100,000— 200,000 tons 150 tons
Over 200,000 tons 200 tons
MATERIALS STANDARD(S) GRADE (S)
Ductile Cast Iron BS EN 1563 ASTM A 536 GB/T 1348
EN-GJS-450 to 500 65-45-12 to 80-55-6 QT450-10 to QT-600-3
Cast Steel ASTM A148 IS 1030 GB/T 11352
65-35 to 80-50 230-450 to 340-570 ZG230-450 to ZG340-640
Anchor Bolts (galvanized) ISO 898 BS 3692 ASTM
Gr. 5.8 to 8.8 (galvanized) Gr. 5.8 to 8.8 (galvanized) ASTM F1554 Gr. 105 (galvanized)
ESC bollards can cope with horizontal angles of ± 900 (except for
pillar bollards which is in all horizontal angles) and vertical angles up
to 600 depending on bollard type.
Design codes recommend that bollards are frequently placed at 15-
30m intervals, often at the same spacing as fenders (either at the
same point as fenders or midway). Another approximate guide is 15%
of the length of the shortest ship.
COATING SYSTEMS
Bollards are supplied as factory standard with a protective coating
suitable for most projects. High performance epoxy or other specified
paint system can be factory applied on request in a choice of colours
and thicknesses. Standard available coatings include (uncoated, zinc
oxide primer or high performance epoxy).
The bollard bodies can also be supplied with Hot Dip Galvanizing
(HDG) on a special request basis. Wear and abrasion from ropes
means paint coatings need regular maintenance. Ductile iron bollards
are far less susceptible to corrosion than cast steel bollards, which
can rust quickly and will need frequent painting to retain full strength.
BOLLARD INSTALLATION
Bollards must be installed correctly for a long and trouble-free service life. Anchors should accurately be installed with a template of the bolting pattern, which ESC can supply on request. Once the grout has cured to full strength, anchors can be tightened to the design preload. A thread loosening compound is frequently applied to allow future removal for replacement. Where possible, recessing the bollard in the concrete is more beneficial than surface mounting.
Fixing options for bollards include:
✓ Surface Mounting
✓ Recess Mounting
✓ Retrofitting
✓ Through bolting
✓ Structural Steel Mounted
QUALITY ASSURANCE
Bollards are safety critical items and quality is paramount. Independent third party witnessing of test is available at additional cost on request. A typical quality documentation package will include:
• Dimensioned drawings of bollard and accessories
• Bollard and anchorage calculations (if required)
• Inspection and test plan
• Certificate of conformance
• Physical, chemical and material properties report for casting and anchorages
• Installation guidelines ANCHOR INSTALLATION
TEMPLATE
Dimension Units Bollard Capacity (Tonne-Force)
10 15 22.5 30 50 80 100 125 150 200 250 300
TB mm 32 40 40 40 50 70 80 80 90 90 120 155
HB mm 205 235 255 255 350 380 410 410 435 500 610 670
WB mm 220 340 350 350 500 550 600 600 700 800 930 980
WT mm 216 410 430 450 640 640 790 850 900 1000 1090 1200
D mm 236 335 355 375 540 550 640 700 750 850 915 925
øB mm 120 160 180 200 260 280 350 350 400 450 500 500
D1 mm 118 130 140 150 220 230 245 275 300 350 370 325
Bolts - M20 M24 M30 M30 M36 M42 M42 M48 M48 M56 M64 M64
Bolt Qty - 4 5 5 5 5 6 7 7 7 8 8 10
Bolt Length mm 450 500 500 500 500 800 800 900 1000 1000 1375 1550
ESC’s latest generation of T Head Bollards
provide a compact high strength bollard system
that can be utilised in a multitude of
configurations. ESC can offer T head bollards at
up to 300 ton capacity in either ductile cast iron
or cast steel materials.
T HEAD BOLLARD
WT
D
D1
Dimension Units Bollard Capacity (Tonne-Force)
15 30 50 80 100 125 150 200 250
TB mm 40 40 50 70 80 80 90 90 120
HB mm 370 410 500 520 570 595 585 660 690
WB mm 400 440 600 660 750 775 850 930 930
WT mm 410 480 640 650 800 820 920 1000 1000
D mm 335 405 540 560 650 670 770 850 850
øB mm 160 200 260 300 350 375 400 450 450
Bolts - M24 M30 M36 M42 M42 M48 M48 M56 M64
Bolt Qty - 5 5 5 6 7 7 7 8 8
Bolt Length mm 500 500 500 800 800 900 1000 1000 1375
T HORN BOLLARD
WT
D
WB
HB
øB
TB
ESC’s latest generation of T Horn Bollards
provide a compact high strength bollard
system that can be utilised in a multitude of
configurations. The main feature is that the
bollard may carry two mooring lines from
different vessels on the same bollard. They are
well suited to general purpose berths.
Note: Anchor Bolts omitted from illustration for clarity
WB
HB
øB
TB
COLD ROLLED SHEET PILES
5
Dimension Bollard Capacity (Tonne-Force)
Units
15 30 50 80 100 125 150 200
TB 40 40 50 70 70 80 80 90 mm
HB 260 280 320 330 350 375 405 435 mm
WB 340 370 480 530 550 640 728 800 mm
WT 320 360 540 560 590 680 760 1000 mm
D 320 360 540 460 490 580 660 850 mm
øB 160 200 260 280 300 325 400 450 mm
Bolts M24 M30 M36 M42 M42 M48 M48 M56 -
Bolt Qty 4 4 4 5 7 7 7 7 -
Bolt Length 500 500 500 800 800 1000 1000 1000 mm
KIDNEY BOLLARD
Kidney bollards are well suited for berths with
low tidal ranges. ESC’s range is for general
purpose applications up to 200 tons, from small
wharves to large vessel terminals. Kidney
bollards are not an optimum body shape for
steel line angles.
WT
D
WB
HB øB
TB
Dimension Units Bollard Capacity (Tonne-Force)
15 20 25 30 35
TB mm 30 40 45 45 50
HB mm 165 180 210 250 270
WB mm 510 665 810 960 1120
WT mm 410 510 610 660 840
D mm 220 280 310 310 400
Bolt - M20 M24 M24 M24 M30
Bolt Qty - 6 6 6 8 8
Bolt Length mm 350 460 460 460 460
CLEAT BOLLARD
Cleat bollards are a low profile bollard well
suited for mooring light commercial or
recreational vessels in small jetties or marinas.
ESC provides cleat bollards in ductile cast iron
or cast steel body materials.
WT
D
WB
HB
TB
ESC Mooring Bollards
Dimension Bollard Capacity (Tonne-Force)
20 30 50 75 100 125 150 200
TB mm 20 20 25 40 50 60 60 60
HB mm 300 350 420 510 600 700 750 840
WB mm 680 780 950 1140 1330 1535 1670 1860
WT mm 540 610 720 870 1020 1170 1270 1430
D mm 280 310 360 440 520 590 640 720
Bolt - M20 M22 M30 M36 M42 M42 M48 M56
Bolt Qty - 8 8 8 10 10 10 10 10
Bolt Length mm 300 300 450 500 600 750 850 1070
DOUBLE BITT BOLLARD
In some regions, referred to as twin horn
bollards, ESC’s double bitt bollards offer the
feature of accepting multiple mooring lines
simultaneously. Their narrow base profile is
also an advantageous feature for wharves
with limited work areas.
WT
D
WB
HB
TB
Dimension Units Bollard Capacity (Tonne-Force)
15 30 50 75 100 150 200
TB mm 45 60 70 80 80 100 110
HB mm 370 490 630 740 790 900 1000
WB mm 260 340 450 500 550 650 750
WT mm 360 420 530 650 760 900 990
D mm 315 380 480 580 685 810 890
D1 mm 145 160 260 285 325 380 465
D2 mm 220 260 340 390 415 460 530
øB mm 160 200 260 290 320 370 430
Bolt - M24 M30 M36 M42 M48 M56 M56
Bolt Qty - 4 5 6 6 7 7 8
Bolt Length mm 400 500 600 600 750 1000 1000
SINGLE BITT BOLLARD
Single Bitt Bollards are well suited for berths with
large tidal ranges and for steep mooring angles. This
configuration is especially popular in North America
and can be utilised simultaneously with multiple
mooring lines.
D
WT
WB
HB
TB
øB D1
D2
COLD ROLLED SHEET PILES
7
Dimension Bollard Capacity (Tonne-Force)
Units
10 15 30 50 75 100 150 200
TB 35 40 50 60 70 70 80 90 mm
HB 180 280 320 350 380 410 450 480 mm
WB 200 300 390 430 500 580 680 740 mm
øA 270 420 500 580 630 700 800 900 mm
øB 125 200 240 280 320 360 400 450 mm
Bolt M20 M24 M36 M36 M42 M48 M56 M64 -
Bolt Qty 4 4 4 4 7 7 8 8 -
Bolt Length 350 400 550 800 1000 1000 1000 1000 mm
PILLAR BOLLARD
Pillar Bollards are well suited for small tidal
range applications and jetties where vessels
can berth on both sides due to its capability
of handling loads in the full 360° horizontal
range.
øA
øB
WB
HB
TB
PILLAR BOLLARD—JAPANESE DESIGN
Dimension Units Bollard Capacity (Tonne-Force)
15 25 35 50 70 100 150 200
WT mm 600 720 720 840 960 1180 1440 1700
øB mm 250 300 300 350 400 450 550 650
WB mm 420 480 480 560 640 720 880 1040
HA mm 88 105 105 123 140 158 193 228
HB mm 438 525 525 613 700 833 1018 1203
HC mm 125 150 150 175 200 270 330 390
Bolt Length mm 750 1000 1000 1150 1300 1300 1600 1800
Bolts - M36 M48 M48 M56 M64 M64 M80 M90
Bolt Qty - 4 4 6 6 6 8 8 8
Recess mm 100 130 130 160 190 270 340 410
WT
WB
øB HB
HC
HA
TB
These pillar bollards follow a time tested design from the
1970s utilising a lower grade cast steel and anchor material
but a larger profile. They exhibit the same design features
as ESC’s modern pillar bollard design but they are to be
recessed underneath above the top of the anchor base (HC)
to reach their design capacity.
Recess
T-HEAD BOLLARD—JAPANESE DESIGN
Dimension Bollard Capacity (Tons)
Units 5 10 15 25 30 35 50 70 100 150 200
WT 360 480 600 720 810 810 945 1130 1365 1765 2250 mm
D 360 480 600 720 720 720 840 1000 1200 1600 2100 mm
WB 300 400 500 600 600 600 700 800 900 1100 1360 mm
WD 150 200 250 300 300 300 350 400 450 648 700 mm
TB 30 40 50 65 70 65 70 80 95 120 150 mm
HA 120 160 200 240 240 240 280 370 380 505 860 mm
HB 380 480 580 680 690 690 780 900 990 1260 1550 mm
WC 300 400 500 600 600 600 700 800 900 1100 1360 mm
Bolt length 450 600 700 850 850 850 1000 1150 1300 1500 2160 mm
Bolts M20 M27 M33 M42 M42 M42 M48 M56 M64 M72 M120 -
Bolt Qty 4 4 4 4 6 6 6 6 6 6 6 -
Recess 90 110 130 160 160 160 170 210 220 265 310 mm
WB
WD
TB
HB
HA
WT
D
WC
Recess
ESC has produced heavy duty T-Head bollards—
Japanese design for ports around Asia, as a time
tested robust design. They exhibit the same design
features as ESC’s modern T-Head bollard design but
they are to be recessed underneath above the top of
the anchor base (HC) to reach their design capacity.
The anchor bolts are also orientated at a 22 angle to
the vertical.
Dimension Units
Bollard Capacity (Tonne-Force)
Surface and Flush Mounted Flush Mounted
30 50 60 80 100 125 150 175 200 250 300
TB mm 50 60 60 70 70 80 90 90 100 120 135
HB mm 380 390 390 530 530 540 550 575 585 595 595
WB mm 200 325 325 365 365 365 365 450 450 450 450
WT mm 140 214 214 250 250 250 250 325 325 325 325
d mm 200 270 270 350 350 350 350 500 500 500 500
D mm 480 480 480 750 750 750 750 900 900 900 1100
Bolt - M30 M36 M39 M48 M52 M60 M64 M60 M60 M68 M68
Bolt Qty - 4 4 4 4 4 4 4 4 4 4 4
Bolt Length mm 500 600 650 720 800 920 1020 1050 1150 1300 1300
TRICORN BOLLARD
ESC Tricorn Bollards is ideal for any mooring
requirement, it is a unique triple-lobed Tricorn Bollard
that provides more holding power than any other
bollard in its class, even on line angles up to 70o. Its
generous trunk diameter reduces mooring line
stresses. Integrated load fuses and capacities for up
to 3000kN are available.
WB
HB d
TB
D
D
WT WB
COLD ROLLED SHEET PILES
9
INTRODUCTION
ESC STRUTTING SYSTEM
CONTACT DETAILS
ESC GLOBAL CONTACT LIST
Australia, New Zealand & PNG Brazil
ESC Asia Limited A 12/F Unit 19, Shatin Galleria, 18-24 Shan Mei Street, Fo Tan, Shatin, New Territories, Hong Kong E [email protected] T +852 3956 1868 W www.escpile.com
ESC Brazil A Sao Paulo, SP, Brazil E [email protected] T +55-11-3170-8598 W www.escpile.com.br
ESC Steel Engineering Sdn Bhd A F-1-2 Second Floor, Block F Suite 5 Setia Walk, Persiaran Wawasan, Pusat Bandar Puchong 47160 Puchong, Selangor, Malaysia E [email protected] T (Malaysia) +6012 428 5759
Mexico, Central & South America
Acerlum ESC SAPI de CV A Loma de la Cañada No. 4, Loma, Querétaro, México CP 76060 E [email protected] T +52 442 4711 500 W www.acerlum-esc.com
Middle East & Africa
ESC Middle East A P.O. Box 131355, Industrial Area City of Abu Dhabi, Mussafah Abu Dhabi, UAE E [email protected] E [email protected] T +971 2550 6188 F +971 2550 6112 W www.escpileuae.com
Netherlands
Europile B.V. A Dam Bustersstraat 7 NL 4651 Sj Steenbergen Netherlands E [email protected] E [email protected] T +31 167 534 747 F +31 167 534 850 W www.europile.com
Nigeria
ESC Nigeria Ltd A No.72, Apt 5, Lome Crescent, Wuse Zone 7, Abuja, Nigeria E [email protected] E [email protected] T +234 7050 8888 22 F +234 8067 3905 66
Russia
ESC-Beregstal Jsc A 20 Ulitsa Lotsmanskaya St Petersburg 190121 Russian Federation E [email protected] E [email protected] T +7812 495 0806 F +7812 325 9357
Ukraine
Mageba Ukraine LLC A Gagarina Str.55, off 466 Cherkasy, 18000 Ukraine E [email protected] E [email protected] T +38 472 503661 F +38 472 503662
Malaysia, South East Asia & South Asia
United States & Canada
Disclaimer The information provided within this Catalogue is for general information purposes only, without any warranty. ESC shall not be held responsible for any errors, omissions or misuse of any of the information provided. ESC disclaims any and all liability resulting from the ability or inability to use the information within this document. Anyone using the information contained does so at their own risk. ESC shall not be held liable for any damages which includes any financial losses or incidental or consequential damages arising from the use of this information. The product range contained is liable to change without notice.
Argentina, Paraguay & Uruguay
Cimtronic Design & Engineering A Vedia 144, 5th Floor, Office 2 (C1429EIB) Nuñez CABA, Argentina E [email protected] E [email protected] T +55 (31) 99976 4714 W www.escpile.com.br
Philippines
ESC Steel Philippines, Inc. A Level 6/F Cyber One Building, 11 Eastwood Avenue, Eastwood City Cyberpark, Bagumbayan, Quezon City, Philippines E [email protected] T +63 2 8464 9383 M +63 917 202 7798 W www.escsteelphil.com
United Kingdom & Ireland
ESC Steel LLC Contact: Bruce Colson A 19701 Bethel Church Rd, Suite 103 #211, Cornelius, North Carolina 28031,USA E [email protected] T +1 (704) 654 0321 W www.escsteel.com
India
ESC India A E/42, Rajdeep CHS, Gokhale Road, Naupada, Thane (W) : 400602, India E [email protected] T +91 9920 160 019 W www.escpile.com
Indonesia
PT ESC Steel Indonesia A Graha Mustika Ratu, 5th Floor #505, Jln. Jend Gatot Subroto Kav. 74-75, Jakarta 12870 E [email protected] E [email protected] T +62 811 980 376 T +62 821 247 99 468
China
ESC Trading (Shanghai) Co., Ltd. A Rm 02, 5/F, No. 16, Gopher Qibao T2 Building, Lane 399, Xinlong Rd., Minhang District, Shanghai, China E [email protected] E [email protected] T +86 21 3126 3501 T +86 21 3126 3502
ESC Steel LLC A (Houston) Market Street 9595 Six Pines Dr. Suite 8210, The Woodlands, Texas 77380 USA E [email protected] E [email protected] T +1 (281) 205 7261 A (North Carolina) 19701 Bethel Church Rd, Suite 103 #211, Cornelius, North Carolina 28031,USA E [email protected] T (Canada) +1 (604) 235 1911 F (Canada) +1 (415) 500 9825 W www.escsteel.com