COIN AND/OR TOKEN DISTRIBUTOR

TECHNICAL MANUAL

rev.

5-1

0-05

-13

X5ccTalk protocol/AES

Document reserved according to the law, with reproduction or transmission to third parties is strictly prohibited without the explicitauthorization of the company MICROHARD s.r.l..Components may be updated and therefore present different details from those depicted below, without this constituting a detrimentdue to the texts contained in these instructions.MICROHARD s.r.l. is not responsible for accidents, breakage, etc. owing to the persons being unaware or not applying the guidelinescontained in these instructions. The same applies to changes and variations and/or use of unauthorized parts.

1rev. 5-10-05-13

INDEX

1 GENERAL INFORMATION

1.1 DESCRIPTION1.2 MAIN FEATURES1.2.1 COIN OUTPUT1.2.2 ERROR CODE

1.2.3 PCB POSITION1.2.4 ccTALK STANDARD1.2.5 CONNECTOR POSITIONS1.2.6 ANTI-JAM SYSTEM1.3 SAFETY1.4 DIMENSIONS

1.5 TECHNICAL DATA1.6 POWER SUPPLY FOR MOTOR

2 INSTALLATION

3 ELECTRICAL INFORMATION

3.1 GENERAL DESCRIPTION3.2 POWER SUPPLY3.3 OPERATING MODES3.4 OPTICAL SENSORS3.5 LED INDICATORS

3.6 COIN LEVEL PLATES

4- ELECTRONIC SPECIFICATIONS

4.1 X5-cc-Talk/AES CONNECTOR MOD.4.2 X5-cc-Talk/AES ADDRESS SELECTION MOD.

4.3 cc-Talk/AES SUPPORTED COMMANDS4.4 X5 DPO - EVO - IN/OUT - CCS SUPPORTED COMMANDS4.5 AES COMMANDS

5 SPARE PARTS

2 rev. 5-10-05-13

1 GENERAL INFORMATION

1.1 DESCRIPTION

X5 is a new coin and token distributor and can be used in various applications such as payment kiosks, automatic cashregisters, slot machines and money changing and coin recycler machines

1.2 MAIN FEATURES

5 product configurations and operating modes

1.2.1 COIN OUTPUT

By using various accessories provided with X5 you can choose from 5 different coin or token output modes bydiverting the flow from the pre-set position.

1.2.2 ERROR CODE

When the yellow LED on the X5 turns on it means the following: that the device has power; the error code is indicatedby means of a series of different flashes, enabling rapid identification of the causes of the malfunction or counting thecoins paid according to ordinary operation.

1.2.3 PCB POSITION

The PCB enables all the X5 functions -Pay-out can be updated from the outside without have to dismantle thedistributor's parts.

1.2.4 ccTALK STANDARD

For the X5 Pay-out versions the unit functions by using the ccTalk standard. You can choose the device with theCinch 12 connector or with the ccTalk standard 10 pins cup connector. The parallel version is available with the cinchconnector only.

1.2.5 CONNECTOR POSITIONS

The connector for ccTalk operation or the 12 pin (Cinch) connector can be set in two different positions:- side opposite coin output window- side of coin output window (reverse)

1.2.6 ANTI-JAM SYSTEM

If the motor or belt jams the motor stops and subsequently restarts in reverse; it then stops again and restarts in thecorrect direction. If this does not occur the operation will be repeated with 3 tries.

1.3 SAFETY

X5 should not be connected/disconnected from the slide base with the power supply on.Do not insert hands into the X5 while operating as there are moving mechanical parts.

3rev. 5-10-05-13

1.4 DIMENSIONS

1.5 TECHNICAL DATA

Distribution speed 4 coins/secCoin capacity 1500 pieces of 1.00 •Weight (empty) 2 kgDiameter coins dispensed from 16 to 39 mm (from 20 to 31.5 mm with standard chain)Thickness coins dispensed from 1.25 to 4.5 mm

1.6 POWER SUPPLY

standby empty max load forced stopMOTOR 24Vdc ± 10% 0 mA 80 mA 500 mA (transient) 500 mALOGIC 12Vdc ± 10% 80 mA 80 mA 80 mA -

standby: X5 stopped but with power onempty: normal operationmax load: operation with coin hopper fullforced stop: refers to value of current absorbed by motor over which it is jammed, and the anti-jam procedure begins.

���

����

�

����

�

���� �����

���

��� ��� ����

4 rev. 5-10-05-13

2 INSTALLATION

DO NOT SUPPLY X5 WITH POWER UNTIL ASSEMBLY AND DUE INSPECTION ARE COMPLETED

- Affix the X5's slide to the machine.- Check that it is properly plugged in if using 12 pin standard connector.- Hook up the flat or 12 pin connector, following the instructions for each single pin as shown in paragraph 4.1, using

a suitable cable to support currents and maximum voltages.- Insert X5 onto the slide until it is totally inserted.- Turn on electric power.

3 ELECTRICAL INFORMATION

3.1 GENERAL DESCRIPTION

The operating modes of X5 are guided by a microprocessor:

ccTalk/AES protocolparallel protocolmulti coin protocolcoin counter and divider

3.2 POWER SUPPLY

X5 is equipped with a 24 v continuous feed motor.

3.3 OPERATING MODES

X5-cc-Talk/AES MOD.Functions with ccTALK/AES protocol.

3.4 OPTICAL SENSORS

There is a pair of optical sensors to determine the coins paid (including coins with a central hole) and a pair of inductivesensors for the multi-coin models.

X5-ccTalk/AES MOD.By means of the data line, ccTalk/AES protocol monitors all the sensors' functions.

3.5 LED INDICATORS

X5-ccTalk MOD.This has just one flashing green LED:rapid flashing indicates that the X5 is distributing one coin per flashflashes with longer intervals indicates that the X5 is in onled constantly on means X5 is in error: this can include photocell error or corrupt data in EEProm or insufficient powersupply.

3.6 COIN LEVEL PLATES

Inside X5 there are brass plates to determine the level of coins.

X5-cc-Talk/AES MOD.Plate signals are internally operated by the ccTalk/AES protocolI.

5rev. 5-10-05-13

4- ELECTRICAL SPECIFICATIONS

N.B. TO CONNECT THE X5 USE A 22AWG CABLE.

4.1 X5-cc-Talk/AES MOD. CONNECTOR

12 Pin connector (12V ccTalk, 24V ccTalk versions)

Pin 1 and Pin 9 power supplyPin 4, Pin 8 and Pin 12 X5 address (as described in paragraph 4.2)Pin 5 data line

The remaining Pins are not connected.

Optional 10-Pin connector mounted on optional MH455a board (versions 12V ccTalk, 24V ccTalk)

Pin 1 data linePin 4 and Pin 8 GNDPin 7 and Pin 10 +24

The remaining Pins are not connected.

�

��

��

��

�

�

�

�

�

�

Pin 1 - GndPin 2 - n.c.Pin 3 - n.c.Pin 4 - Add. select 1Pin 5 - Data ccTalkPin 6 - n.c.Pin 7 - n.c.Pin 8 - Add. select 2Pin 9 - +24VPin 10 - n.c.Pin 11 - n.c.Pin 12 - Add. select 3

�

��

�

�

�

�

� �

Pin 1 - Data ccTalkPin 2 - n.c.Pin 3 - n.c.Pin 4 - GndPin 5 - n.c.Pin 6 - n.c.Pin 7 - +24VPin 8 - GndPin 9 - n.c.Pin 10 - +24V

6 rev. 5-10-05-13

Flat 10 Pin Connector (12V ccTalk, 24V ccTalk versions)

Pin 1 data linePin 4 and Pin 8 GNDPin 7 and Pin 10 +24

The remaining Pins are not connected.

USB Connector 24V ccTalk version)

Separate power supply 24VDC - 12VDC (optional)on connector "mini-fit" 2 poles.

4.2 X5-cc-Talk/AES MOD. ADDRESS SELECTION

The X5-cc-Talk address is selected by means of the Add.Select 1, Add.Select 2, Add.Select 3 symbols according tothe following table:

Add. select 1 Add. select 2 Add. select 3 Serial add.3

ON 4ON 5ON ON 6

ON 7ON ON 8ON ON 9ON ON ON 10

By using the flat 10 pin connector it is possible to choose the various addresses, setting the dip-switch, with the 12pin connector you can choose using pin 4, pin 8 and pin 12.

� �

� � � � �

� � �

Pin 1 - Data ccTalkPin 2 - n.c.Pin 3 - n.c.Pin 4 - GndPin 5 - n.c.Pin 6 - n.c.Pin 7 - +24VPin 8 - GndPin 9 - n.c.Pin 10 - +24V

7rev. 5-10-05-13

4.3 cc.talk/AES SUPPORTED COMMANDS

Header 254 Simple pollHeader 253 Address pollHeader 252 Address clashHeader 251 Address changeHeader 250 Address randomHeader 247 Request variable setHeader 246 Request manufacturer idHeader 245 Request equipment category idHeader 244 Request product codeHeader 242 Request serial numberHeader 241 Request software revisionHeader 236 Read opto statesHeader 219 Enter new PIN numberHeader 218 Enter PIN numberHeader 217 Request payout high / low statusHeader 216 Request data storage availabilityHeader 215 Read data blockHeader 214 Write data blockHeader 192 Request build codeHeader 172 Emergency stopHeader 171 Request hopper coinHeader 169 Request address modeHeader 168 Request hopper dispense countHeader 167 Dispense hopper coinsHeader 166 Request hopper statusHeader 165 Modify variable setHeader 164 Enable hopperHeader 163 Test hopperHeader 161 Pump RNGHeader 160 Request cipher keyHeader 004 Request comms revisionHeader 003 Clear comms status variablesHeader 002 Request comms status variablesHeader 001 Reset device

4.4 X5 DPO - EVO - IN/OUT - CCS SUPPORTED COMMANDS

Header 224 Dispense coinsHeader 223 Dispense changeHeader 206 Empty payoutHeader 160 Request cipher keyHeader 133 Request hopper polling valueHeader 132 Emergency stop valueHeader 131 Request hopper coin valueHeader 130 Request indexed hopper dispense countHeader 121 Purge Hopper

8 rev. 5-10-05-13

4.5 AES COMMANDS

Basic commands

254 Simple poll Hopper, Validator251 Address change Hopper, Validator249 Request polling priority Validator245 Request equipment category id Hopper, Validator235 Read DH public key Hopper, Validator (*)234 Send DH public key Hopper, Validator (*)230 Request inhibit status Validator (*)229 Read buffered credit or error codes Validator223 Modify inhibit and override registers Validator210 Modify sorter path Validator209 Request sorter path Validator206 Request sorter path Hopper, Validator200 Request product parameters Hopper, Validator192 Request build code Hopper, Validator172 Emergency stop Hopper167 Dispense hopper coins Hopper166 Request hopper status Hopper164 Enable hopper Hopper160 Request cipher key Hopper, Validator3 Clear comms status variables Hopper, Validator2 Request comms status variables Hopper, Validator1 Reset device Hopper, Validator

244 Request product code Hopper242 Request serial number Hopper241 Request software revision Hopper236 Read opto states Hopper217 Request payout high/low status Hopper205 Modify bus baude rate Hopper168 Request hopper dispense count Hopper163 Test hopper Hopper

Optional commands

(*) command not encrypted

9rev. 5-10-05-13

5 SPARE PARTS

Use exclusively original spare parts to replace any components.

Use of non-original and/or non conform parts (if not authorized exclusively by the assistance center inwriting) release the manufacturer from all liability.

To request spare parts, photocopy the page of the pertinent spare parts table and fill out the tablecompletely, indicating the table containing the part, its reference number on the drawing and the quantityof parts requested, and your details.

Requests lacking the above data will not be taken into consideration.

Send the copy/ies by fax to the number +39 0547 81247

SPARE PARTS REQUEST FORMSend copy by fax to the number +39 0547 81247

TABLE NUMBER QUANTITY TABLE NUMBER QUANTITY TABLE NUMBER QUANTITY

Company name

Address

City/Town

Tel.

Fax

Date of request

Stamp/Signature

CUSTOMER DATA

10 rev. 5-10-05-13

TAV. 1 - PAYOUT PART CHIENC CONNECTOR

��

�������

���

������

�

�� �

����

��

�����������������������������������������������������

���������

�

������ ������

��

�����

���� ��

������

��

��

LOCK

MOTOR

11rev. 5-10-05-13

TAV. 2 - PAYOUT PART CONNECTOR CCTALK

��

�������

���

������

�

�

��

�

���������������������������� �� �������������������������������������������

���������

�

������ ������

��

�����

�������

����� �

��

�

LOCK

MOTOR

12 rev. 5-10-05-13

TAV. 3 - STANDART VERSION

� �� �� ��

�

13rev. 5-10-05-13

TAV. 4 - SIDE VERSION

� �� ��

�

�

14 rev. 5-10-05-13

TAV. 5 - DYNAMIC PAY OUT

��

��

��

��

��

��

��

�

�

��

�

15rev. 5-10-05-13

TAV. 6 - COIN COUNTER

�� � � �� �� �� ��

��

���

�

�

16 rev. 5-10-05-13

TAV. 7 - EVO

��

��

� �� ��

�� ��

��

� �� �

Microhard s.r.l.Via dei Platani. 7 - 47042 Cesenatico (FC)

TEL.: 0039-0547 75450 FAX: 0039-0547 81247info@microhard.itwww.microhard.it