Coastal Product Guide · Finelight™ Grilles-Between-The-Glass** Removable Interior Grille...

Coastal Product Guidefor Professionals

1

Casement & Awning Windows . . . . . . . . . . . . . . . . . . . . . . . 9

Tilt-Wash Double-Hung Windows . . . . . . . . . . . . . . . . . . . . 21

Specialty Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Elliptical & Circle Top™ Windows Circle & Oval Windows Flexiframe® Windows Arch/Custom Arch Windows Springline™ Windows

Frenchwood® Gliding Patio Doors . . . . . . . . . . . . . . . . . . . . 47

Frenchwood® Hinged Patio Doors - Inswing . . . . . . . . . . . . 53

Frenchwood® Hinged Patio Doors - Outswing . . . . . . . . . . . 61

Combination Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Performance Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

That’s the promise of Andersen® 400 Series windows and doors with Stormwatch® protection. Stunning aesthetics that make any project appealing and built-in protection that can stand up to Mother Nature* at her crankiest — as well as the coastal building codes. What’s more, a myriad of tantalizing options allow you to create one-of-a-kind windows and doors to suit your most innovative designs instead of altering plans to accommodate the one-style-fits-all inventory favored by many of our competitors.

Contents

400 Series Pretty. Tough.

Coastal products featuring the Stormwatch Protection insignia

also carry the Andersen promise of quality materials and precise construction.*

That’s why they are all backed with Owner-to-Owner® limited warranties, such as

a 10-year limited warranty for impact-resistant glass. For complete information on

our limited warranties, visit andersenwindows.com or contact your Andersen supplier.

Many structural enhancements are

added to our coastal products to

make them stand up to harsh weather

conditions – impact-resistant glass,

special fasteners, high-strength

silicone glazing, frame, sash and

panel reinforcement, heavy-duty

hardware, and additional

locks are just a few of them.

Performance Grade Upgrades

are also available on many standard

Andersen® 400 Series windows and

doors when impact-resistant glass

is not needed. Options are presented

in each product section. An Andersen

supplier can provide details.

*See limited warranty for details .

Retracted

Engaged

1

Andersen products feature Perma-Shield® vinyl cladding. A well-proven

asset in coastal areas, it resists salt spray and sea air far better than

aluminum. It never loses its luster and it never requires painting.*

*See limited warranty for details .

For quick estimates, just enter your project information and the fast

and easy-to-use Online Performance Grade Estimator, Coastal Product

Finder and Test Report Finder will estimate the design pressure

requirements, then identify the Andersen products that are best for your

situation. You can even print test reports and certification documents

for the products selected. Remember to have all estimates confirmed

by a qualified architect or structural engineer. To use our convenient

online tools, just log on to andersenwindows.com/stormwatch

Choose Andersen 400 Series windows and doors with Stormwatch protection. Not only do they possess uncompromising beauty, they’re strong enough to take whatever Mother Nature* – and the tough coastal building codes – dish out. And that’s pretty tough to come by.

Andersen® windows and doors with Stormwatch®

protection come with a variety of glass options

to satisfy nearly any building need. Remarkably

energy-efficient Low-E4® glass is standard on

all Andersen 400 Series products. But that’s

just the beginning. You can also specify

impact-resistant glass that’s strong enough

to withstand high winds and debris,* exquisite

patterned glass, and more (see pages 2-3).

Andersen® Finelight™ grilles-between-the-glass have been added

to our many standard grille options to enhance the look of traditional

homes without compromising weather resistance (see pages 2-3).

Highly-popular Frenchwood® patio doors are among the multitude of design

choices available to give homes a unique and elegant aspect – all available

in custom sizes. Select sizes are available with Performance Grade (PG)

Upgrades when impact-resistant glass is not required (see page 5).

2

In a coastal environment, it’s not enough to just look good. You need windows and doors that can withstand some of nature’s most violent mood swings – and still look good. To that end Andersen offers a wide array of grille options, from standard patterns to custom designs – and now full divided light grilles and Finelight™ grilles-between-the-glass. They all feature prominently defined profiles to give you the precise authentic look you’re searching for. And the windows all are fully empowered with Stormwatch® protection.

See the Andersen® Product Guide for more divided light patterns or visit andersenwindows .com/grilles .

STandardA full selection of standard grille patterns makes specification simple and easy . See the Andersen® Product Guide or visit andersenwindows .com/grilles for more information on our full array of standard patterns including Colonial, Modified Colonial, Short/Tall Fractional, Prairie A, Victorian and other options .

SPecified equal lighTSpecified equal light patterns allow you to create anoriginal look without the costs normally associated with custom grilles . Just tell us how many equal rectangular lights across and how many down, and we’ll make it . You can add one row or column to the standard Colonial style grille pattern, or delete rows and columns before it becomes a fully customized order .

cuSTomFor a truly signature look, Andersen will work with you to create custom grille patterns . Andersen can accommodate nearly any pattern and we are always eager to see new ideas . See your Andersen supplier for details .

Widths

Patterns

Andersen divided light is available in four widths for increased design flexibility .

Monolithic impact-resistant glass is reinforced with a clear plastic laminate sandwiched between two panes to resist impact, forced entry, sun damage and unwanted noise .

Standard on all Andersen® 400 Series products, High-Performance™ Low-E4® glass employs a hermetically-sealed system for optimum installation from heat and cold . (PG Upgrades Only)

High-Performance™ Low-E4® impact-resistant glass provides all the benefits of monolithic impact-resistant glass, while adding an insulating air space that helps keep homes cool in summer and warm in winter .

Impact-resistant glass is one component of Stormwatch® protection. This graduated combination of upgrades lets you order Andersen® 400 Series windows and patio doors with the exact glass and structural enhancements needed to comply with virtually any coastal building requirement. Enhancements include tempered safety glass and glass that is laminated for added strength. In addition, we provide several glass options. High-Performance™ Low-E4® glass provides energy efficiency and sparkling clarity. High-Performance™ Low-E4® SmartSun™ glass allows sunlight to stream through while blocking unwanted solar heat and damaging ultraviolet rays that can cause fading. High-Performance™ Low-E4® Sun glass is ideal for helping to cut cooling costs and minimizing UV light that can cause fading.

PrairieColonial 2 Wide/1 High 3 Wide/3 High Custom Custom

2

Pretty is as pretty does.

it starts with glass.

3

Monolithic impact-resistant glass is reinforced with a clear plastic laminate sandwiched between two panes to resist impact, forced entry, sun damage and unwanted noise .

Standard on all Andersen® 400 Series products, High-Performance™ Low-E4® glass employs a hermetically-sealed system for optimum installation from heat and cold . (PG Upgrades Only)

3

High-Performance™ Low-E4® Glass

Permanent Exterior*Permanent Interior With Spacer

For a truly authentic look, full divided light features permanently-applied interior and exterior grilles with spacers between the glass . Interior grilles are available in unfinished pine, maple, oak or prefinished white .

configurations All grille configurations can be ordered with interiors and exteriors to match window and patio door interiors and exteriors .

Permanent Exterior*Permanent Interior

Permanent Exterior*Removable Interior

Simulated divided light offers permanent grilles on the exterior and interior with no spacer between the glass . We also offer the option of permanent exterior grilles with removable interior grilles . Interior grilles are available in natural wood or prefinished white .

* Exterior grilles are made of patented Fibrex® material, so they’ll stand up to corrosion and rot — even in coastal areas . See limited warranty for details . Available in colors to match product exteriors .

full divided light Simulated divided light easy-clean options

Finelight™ Grilles-Between-The-Glass**

Removable Interior Grille

Removable interior grilles snap off for easy cleaning . Andersen® Finelight™ grilles are suspended between the glass panes and feature a contoured 3 ⁄4'' profile . Finelight™ grilles are installed during manufacture and must be ordered with the unit .

NOTE: Please check with your Andersen supplier for available patterns .

** Tinted glazing may affect the appearance of Finelight™ grille color .

Starts cleaner. Stays cleaner.All windows and doors with Stormwatch® protection are protected during construction by a translucent film that minimizes time spent masking, then peels away for a spotless window .

Even better, when the exterior of our glass is activated by sunlight,

it dries faster, stays cleaner longer, and eliminates up to 99% of water spots .

For details, contact your Andersen supplier or log on to andersenwindows .com .

Ordinary Glass

44

add some style to your upgrades.

andersen® art glassAvailable in eleven original patterns, including four Frank Lloyd Wright® series designs – see Andersen® Product Guide or visit andersenwindows.com/artglass for pattern information.

Not only do we provide upgrades that will make your windows stronger, we have options that will make them prettier.

Patterned glassDesigned to let in light while obscuring vision, our patterned glass can be specified along with most standard and tempered glass options.* (For Performance Grade Upgrades only.)

hardwareGet the look you’re after – inside and out – with our myriad of hardware styles, finishes and options. Only a few examples are shown here. Refer to each section for the hardware available with specific products.

Obscure Pattern Cascade Pattern Fern Pattern Reed Pattern

Colonnade

Double-Hung Hardware in StoneNewbury® Hinged

Patio Door Hardware in Polished Chrome

Eucalyptus Prairie Rhythm Wichita

Tribeca® Gliding Patio Door Hardware in White

“Frank Lloyd Wright” is a registered trademark of the Frank Lloyd Wright Foundation .*Cascade and Reed patterns can be ordered with either a vertical or horizontal orientation .

Folding Casement Hardware – Contemporary in White

Estate™ Casement Hardware in Satin Nickel

Exterior Colors Interiors Finish options vary by hardware style, see product section for details .

White Sandtone Terratone® Forest White Pine Oak Maple Bright Antique Polished Brushed Oil Rubbed Satin Distressed Distressed White Stone Gold Black Green Brass Brass Chrome Chrome Bronze Nickel Bronze Nickel Dust

Casement Window

Awning Window

Tilt-Wash Double Hung Window†

Specialty‡‡

Frenchwood® Gliding Patio Door

Frenchwood® Hinged Patio Door‡

Frenchwood® Outswing Patio Door

This data is accurate as of August 28, 2009 . Due to ongoing product changes, updated test results, or new industry standards, this data may change over time . Call your Andersen supplier for current performance information or upgrade options .

Printing limitations prevent exact color duplication . See your Andersen supplier for actual color samples .† Estate™ hardware is available as an option for tilt-wash units with PG Upgrades only, not impact glass units .

PRODUCT FEATURES HARDWARE FINISHES UNIT DIMENSIONS†† PERFORMANCE VALUES GLAZING OPTIONS

(Circle Top,™ elliptical, circle, oval, arch, Springline™ enhancement, custom arch and Flexiframe® windows)

5

Exterior Colors Interiors Finish options vary by hardware style, see product section for details .

White Sandtone Terratone® Forest White Pine Oak Maple Bright Antique Polished Brushed Oil Rubbed Satin Distressed Distressed White Stone Gold Black Green Brass Brass Chrome Chrome Bronze Nickel Bronze Nickel Dust

5

for less demanding needs, we offer Pg upgrades on standard windows and doors. Often homeowners can get by with fewer and less elaborate enhancements than those found on products with impact-resistant glass and still satisfy local building codes. That is why we offer Performance Grade (PG) Upgrades on many standard Andersen® 400 Series windows and doors. A few of the upgrades available with 400 Series tilt-wash double-hung windows are listed below. Contact your Andersen supplier to determine which products are right for you.

TruScene® insect ScreenMade with a micro-fine stainless steel mesh that’s one-third the diameter of conventional screen wire, TruScene® insect screens provide over 50% more clarity for a beautifully unobstructed view. They allow more fresh air and sunlight in, while keeping out even the smallest insects.†

AluminumInsect Screen

†All comparisons are made to Andersen® aluminum insect screens .

ASTM E1886/ Total Unit Performance,

Width Height

Basic Units Performance E1996 NFRC; HP Impact; w/o Grilles

Glazing Types Grilles Rating^ DADE TAS Minimum Maximum Minimum Maximum 201, 202, 203 U-Factor SHGC

For more information about individual products – plus listings for picture, transom, sidelight and Circle Top™ units – refer to individual product sections throughout this catalog .

For more information about the performance values in this chart, refer to the Performance Data section starting on page 75 .

High-Performance™ Low-E4® and High-Performance Low-E4 Sun glass exterior reflective tint may vary from unit to unit .

1'-5" 5'-11 7/8" 2'-0 1/8" 5'-11 7/8" 113 DP +70/-70 ASTM, DADE 0 .33 0 .31

2'-0 1/8" 4'-11 7/8" 1'-5" 2'-7 1/2" 66 DP +60/-65 ASTM, DADE 0 .33 0 .31

1'-9 5/8" 3'-9 5/8" 3'-0 7/8" 6'-4 7/8" 99 DP +50/-65 ASTM 0 .35 0 .31

Various Various Various Various ‡ ‡ DP +50/-65 ASTM, DADE 0 .26 - 0 .31 0 .33 - 0 .34

2'-8" 7'-11 1/4" 6'-7 1/2" 7'-11 1/2" 18 DP +50/-65 ASTM, DADE 0 .33 0 .26

2'-0 1/2" 8'-11 1/8" 6'-7 1/2" 7'-11 1/2" 24 DP +50/-65 ASTM 0 .32 0 .24

2'-0 1/2" 5'-11 1/4" 6'-7 1/2" 7'-11 1/2" 24 DP +50/-65 ASTM, DADE 0 .32 0 .24

HP Low-E4 (High-Performance™ Low-E4®)

Standard HP Low-E4® Sun glass

IR (Impact-Resistant)

HP Low-E4® IR glass

HP Low-E4® SmartSun™ IR glass

HP Low-E4® Sun IR glass

HP Low-E4® tempered IR glass

HP Low-E4® SmartSun™ tempered IR glass

HP Low-E4® Sun tempered IR glass

Monolithic clear IR glass ‡Monolithic tinted IR glass ‡

Full divided light, simulated divided light,

Finelight™

grilles-between-the-glass, and removable wood

interior grilles

†† Unit dimension always refers to outside frame to frame dimension . ̂ Performance ratings are based on units with Stormwatch Protection and High-Performance™ Low-E4®

Impact-Resistant Glass . For more information see Performance Data section starting on page 75 .‡ Monolithic glass not available in hinged patio doors .‡ ‡ Up to 50 square feet for High-Performance impact-resistant glass and up to 30 square feet for monolithic glass .

PRODUCT FEATURES HARDWARE FINISHES UNIT DIMENSIONS†† PERFORMANCE VALUES GLAZING OPTIONS

1-1/2" high sill stop improves resistance to water infiltration . **

Heavy-duty sash pivot pins allow the sash to tilt to the inside for easy cleaning .

Interior brackets provide additional structural support for the sash and frame .

Exterior frame and sill brackets provide structural support for the sash during storm pressures .

Interior wood stops are secured to the frame using 1-1/2" 16 gauge crown staples instead of nails

PG Upgrades are also available with select 200 Series products .

NOTE: Woodwright® products with PG Upgrade do not have the same hardware enhancements that the tilt-wash windows have .

**Infringes on the overall net clear opening . Unit clear opening are may not meet egress requirements . See your local code official for more information .

66666

installation accessories

Color Length Depth WidthAuxiliary Casing W,S,T,FG 150" (3810) 1-3/16" (30) 1-3/16" (30)Vinyl Laminated Board W,S,T 96" (2438) 1/2" (13) 24" (610)

W 96" (2438) 1/2" (13) 48" (1219)

W 120" (3048) 1/2" (13) 48" (1219)Rigid Vinyl “H” Channel W 84" (2134) & 150" (3810) 3/4" (19) 1" (25)

S,T 84" (2134) & 150" (3810) 3/4" (19) 3/4" (19)Rigid Vinyl “h” Channel W,S,T 150" (3810) 1/2" (13) 1" (25)Rigid Vinyl “J” Channel W,S,T 150" (3810) 1/2" (13) 3/4" (19)

Auxiliary Casing Auxiliary casings consist of a wood core treated with water-repellent preservative and sheathed in rigid vinyl . They are available in White, Sandtone, Terratone® or Forest Green colors . The dimensions are 1-3/16'' (30) by 1-3/16'' (30) in 150'' (3810) lengths .

Installation accessories are designed specifically for trim and installation of Andersen products. Trim strips, channel and laminated board are available in a variety of lengths, widths, thicknesses and shapes as shown in the table below. These accessories are offered in four colors: White, Sandtone, Terratone® or Forest Green. Vinyl trim board has a textured finish.

all you need to know about andersen® coastal products.The following pages contain the Andersen® coastal products that are available to meet the demands of nature as well as the tough coastal codes. You’ll find basic product descriptions, size charts, vertical and horizontal detail drawings, specifications for opening dimensions, joining information and important product performance data. Additionally, we have listed optional accessories that complement the units both here and in each individual product section. You’ll also find key considerations regarding the use and installation of every Andersen product. Keep the instruction guidelines and safety information in mind when considering the installation and use of any Andersen product for your coastal building needs. Should you have any questions, contact your local Andersen supplier. Thank you for considering and using Andersen products.

Rigid vinyl “J,” “h” and “H” chan nel and vinyl lam i nat ed board

Extension Jambs Available for most Andersen products . See individual sections for details .

Continuous Drip-Cap • Included on 400 Series windows

with side-by-side (vertical) mulls

• Available in White, Sandtone, Terratone® and Forest Green .

• Heavy 24-gauge corrosion- resistant aluminum construction

• Available in 6', 10' and 12' 7-1/2'' lengths

77

Rough Sill

Gusset plate

Pan head screws

3/16"Top of screws to bottom of gusset plate.

Unit 2

Unit 1

Beveled sill

Interior

Shims at sill

1/4" minimum space at head

Rough Opening Width

Roug

h Op

enin

g He

ight

1/4" minimum space at sides

Varies

1/4"min.

Example of window unit installed using Andersen published rough opening dimensions.

Example of alternative for built-up sill requiring adjustment to Andersen published rough opening dimensions.

Interior

Shim at sill

Sill �ashing membrane

Installation clip

House wrap

Example of sill �ashing as depicted in Andersen installation guide.

Example of two units joined together with the use of gusset plates and pan head screws that will likely require adjustment to rough opening.

Adjustroughopening

Roughopening gap

Rough SillInterior

Shim at sill

Sill �ashing membrane

Installation clip

House wrap

The purpose of a rough opening is to allow for proper spacing between the window or patio door unit and the building structure . The extra space is required for leveling and squaring the unit during installation, to allow for settling and movement of building materials and to provide an area for insulation . A rough opening that is too small may affect unit operation . A rough opening that is too large may not allow for adequate fastening of the unit to the building structure . Andersen rough opening dimensions are provided as a guideline to help determine the amount of space needed between the window or patio door and the building structure . Depending on the window or patio door type, Andersen recommends 1/4" to 3/8" at each side and 1/2" to 3/4" for height . See appropriate product sections for rough opening guidelines for each product.

Keep in mind that rough opening dimensions may need to be altered from published guidelines depending on installation methods, joining methods, replacement methods, etc . For example, flashing systems can reduce the amount of available rough opening space and should be factored in when calculating rough opening dimensions . The use of support or joining materials will encroach on the rough opening and may require additional rough opening space between the unit and the building structure, depending on the thickness of the flashing system and joining materials used .

To facilitate drainage, the sill plate should be protected and level or slightly pitched to the exterior; it should never slope toward the interior . For even better drainage in challenging environments, consider using a sill pan or beveled siding at the sill per EEBA’s (Energy and Environmental Building Association) Water Management Guide (www .eeba .org), taking into account the added height required when framing the rough opening .

general noTeSWhen ordering, make certain you specify, then verify, the exact product, unit dimensions, configuration requirements, color and options you desire on each window or patio door . Before installing the product, we suggest you verify that it includes the features and options you ordered . When joining windows in combination other than shown in this catalog, contact your local Andersen® supplier for specific installation procedures . Printing limitations prohibit exact color duplication of product . Use actual sample for building specifications .

Andersen Corporation reserves the right to change details, specifications or sizes without notice . The customer assumes all risk of alterations made to Andersen products .

imPorTance of ProPer inSTallaTionProper installation and maintenance of Andersen products is essential to attain optimum performance and operation . Written installation instructions which provide guidelines for proper installation are typically provided with Andersen products . They are also available from your local Andersen supplier or by visiting andersenwindows .com . Remember that every installation is different, and Andersen strongly recommends consultation with the local supplier or an experienced contractor, architect or structural engineer prior to the installation of any Andersen product . The method of attachment for Andersen products, fastener selection and code compliance is the responsibility of the architect, building owner, contractor, installer and/or consumer .

For more complete installation details, refer to the Andersen Architectural Detail File or contact Andersen Corporation .

anderSen furniShed ParTSAlways request genuine Andersen accessories . Light colored areas shown on detail drawing are basic parts furnished by Andersen . Dark colored areas are recommended Andersen parts to complete unit assembly and need to be specifically ordered .

codeSAppropriate selection of Andersen® products which conform to all applicable laws, ordinances, building codes and safety requirements is the sole responsibility of the architect, building owner and/or contractor . Check with your local Andersen supplier and building code officials for specific information .

rough openings

88

Installation Information

general inSTallaTion guidelineSRead and follow the installation guide in its entirety .

1 . Use the appropriate drainage plane on the building (housewrap, building paper, etc .) .

2 . Make certain the drainage plane is continuous (proper overlaps to shed water, taped seams, etc .) .

3 . Read and follow the installation guides .

4 . With the exception of skylights, Andersen® products should be installed only in the vertical position .

5 . Check the rough opening to make sure it is sized properly and is square and level . See page 7 for more rough opening details .

6 . Install the window plumb .

7 . Install the window level .

8 . Install the window square (diagonal measurements should be within 1/8") .

9 . Follow installation guides to properly locate shims and to make sure that units are plumb, level and square . Shims are often required under the window jambs at the sill and along the jambs on the sides .

10 . Check for squareness of unit before final anchoring in wall .

11 . Anchor the window properly with appropriate fasteners (nails or screws spaced as directed) .

12 . Integrate the window into the drainage plane of the wall using high-quality flashing and sealing materials . All flashing materials should be properly overlapped to shed water .

13 . Allow 1/4" for a sealant joint around perimeter of unit between exterior finish materials and unit .

14 . Insulate the interior cavity between the window frame and the rough opening . Do not overpack .

15 . Check installation and operation of unit before application of interior trim .

16 . Stain and/or seal all unfinished wood surfaces promptly to minimize moisture absorption .

SafeTY glaSSUnless specifically ordered, Andersen® windows with High-Performance™ Low-E4® impact-resistant glass are not made with safety glass on the outside light, and if broken, the glass could fragment, causing injury . Andersen windows may be ordered with tempered glass, which may reduce the likelihood of injury when broken . All Andersen patio doors are made with tempered or tempered laminated glass . Differences in appearance between tempered and non-tempered glass can be expected . Slight visual distortions may be noticeable and occur normally as a result of the tempering process . Building codes require safety glass in locations adjacent to or near doors or at other locations .

WindoW and PaTio door SafeTYWindows may provide a secondary avenue of escape or rescue in an emergency, such as a fire . Every family should develop an escape plan and make sure family members know how to escape from the home in an emergency . In your plan, include two ways to escape from every room in case one way is blocked by fire or smoke and make sure you have a designated meeting place outside . A window or a door is an alternate means of escape or rescue . Practice your plan until each member of the family understands it and is able to escape without assistance . Remember, you may not be able to reach children during a fire emergency . Teach children – even very young children – that they must escape from a fire in the home and never hide from the fire or from emergency personnel .

imPacT glaSS uniTS noTicePlease note that Andersen® coastal products with impact-resistant glass are not hurricane- or shatter-proof . However, Andersen coastal products glazed with impact-resistant glass are less susceptible to object penetration when broken than units glazed with other types of glass . Coastal products are tested to the impact performance requirements of The Large Missile Test of ASTM E1996/E1886 and/or Miami-Dade TAS201, 202, 203 . Coastal products with impact-resistant glass have been tested for air, water and structural performance based on the requirements of a specific product performance rating . However, when these units are subjected to intense storms or extreme conditions, which exceed the intended product performance rating, air and water infiltration and flying debris penetration may occur .

In the event of an intense storm or extreme weather conditions, DO NOT stand in front of windows and doors . Make sure all windows and doors are closed, locked and any auxiliary hardware (tilt-wash fold-down brackets) are engaged . Remove all window and door accessories such as grilles, art glass panels and insect screens . Seek safety at approved evacuation locations . If none are available, follow your community's pre-determined evacuation route to a safe location .

lookouT for kidS® ProgramThe Consumer Product Safety Commission has said: “Keep children away from open windows to prevent falls . Don’t depend on insect screens to keep the child from falling out of the window . They are designed to keep insects out, not children in . Avoid placing furniture near windows to keep children from climbing to a window seat or sill .” In an effort to educate consumers about the potential for child falls from windows, Andersen Corporation created the LookOut For Kids® Program .

It combines a window safety brochure and specific product instructions to help make window and door safety an important priority for consumers . For more information on child safety, write:

Andersen Corporation LookOut For Kids Program 100 Fourth Avenue North Bayport, MN 55003 Call 1-800-313-8889 or Email us at: lofk@andersencorp .com

exTerior PainTing/Sealing of anderSen® ProducTSMost Andersen® products include Perma-Shield® prefinished exteriors that are available in a variety of colors . The exterior of some Andersen products may be painted or stained . However, improper painting and staining may cause damage to vinyl, aluminum and other exterior materials . Please adhere to the following guidelines when painting Andersen product exteriors .

• Products in Sandtone or Terratone® color may be painted any color lighter than Terratone color using quality oil-base or latex paint .

• When painting White units, submit color samples to Andersen for approval .

• When painting White, Sandtone or Terratone colored units any color darker than Terratone color, submit color samples to Andersen for approval .

• Do not paint Forest Green exteriors .

• Creosote-based stains should not come in contact with Andersen products .

• Do not paint weatherstripping .

• Do not use abrasive cleaners or solutions containing corrosive solvents on Andersen products .

• Andersen does not warrant the adhesion of paint to product exteriors .

• For additional painting and preparation instructions, contact your Andersen supplier .

cauTionS1 . Directly applying certain types of after-market film to surfaces of the insulating glass in

windows or patio doors may cause thermal stress conditions and result in glass breakage or seal failure . Andersen Corporation is not responsible for product performance when films are applied to Andersen products .

2 . The use of removable insulating materials such as insulated window coverings, shutters and other shading devices may also cause thermal stress conditions and/or deformation of protective vinyl . In addition, excessive condensation may result, which can have a deteriorating effect on the window or patio door unit(s) involved . Andersen Corporation is not responsible for product performance when these kinds of materials or devices are applied to or used in conjunction with Andersen products .

3 . In masonry wall construction, leave adequate clearance between sill, jambs and masonry for caulking and dimensional change of framework .

4 . Acid solutions commonly used to wash brick and other masonry materials do not affect exterior cladding, but may etch the glass and cause seal failure . Follow the acid solution manufacturer’s recommendations carefully and also be careful to protect and/or cover the entire window unit before washing down brick . Damage caused by acid solution is not covered under the Andersen limited warranty .

Casement & Awning Windows

Andersen® casement and awning windows feature an attractive, seamless

exterior appearance, and their slender sash help bring sunshine inside.

Section Reference

Casement

Table of Basic Sizes .......... 12

Basic Unit Details ............... 13

Joining Details ................... 13

Opening Specifications ...... 16

Combination Design.......... 70

Performance Data ............. 75

Awning

Table of Basic Sizes .......... 14

Basic Unit Details ............... 14

Opening Specifications ...... 18

Combination Design.......... 70

Performance Data ............. 75

see your Andersen supplier for details.

see your Andersen supplier for details.CUSTOM SIZING!CUSTOM SIZING!

400

C

asem

ent&

Awni

ngW

indo

ws

10

Features

Hardware Sold Separately.

Available in bright brass, antique brass, polished chrome, brushed chrome, satin nickel, oil rubbed bronze, distressed nickel and distressed bronze.

Classic Series™ HardwareFolding HardwareEstate™ Hardware


White Sandtone Terratone® ForestGreen

HaRdwaRe

The Smooth Control™ hardware system employs a worm gear drive for easy operation. The split-arm operator moves the sash away from the frame to provide for easier glass cleaning.

Operators are attached with additional screws for

improved strength and stability.

A single-actuation lock releases the sash for easy opening while the “reach-out” action eliminates binding when closing. The lock bezel and handle are offered in finishes that coordinate with your specified hardware style option.

Some sizes have an additional lock for added

reinforcement. C2-C25 sizes have a single lock. C3-C35 sizes have two locks. C4-C6 sizes have three locks.

* For complete information on our limited warranties, visit andersenwindows.com or contact your Andersen supplier.

Lighthouse icon indicates Stormwatch® protection.

FRame

A seamless one-piece, pre-formed rigid vinyl frame cover is secured to the exterior of the frame to protect the wood frame from moisture and maintain an attractive appearance while minimizing maintenance.

Andersen® casement and awning windows are available in four neutral colors. Specify White, Sandtone, Terratone® or Forest Green color.

Venting units have a full-length,

corrosion-resistant exterior frame snugger, adding rigidity to the unit.

The seamless rigid exterior vinyl cover extends 1-3/8" (35) around the perimeter of the unit. This creates a flange for helping to attach the unit to the structure.

Wood frame members are treated with a water- repellent wood preservative for long-lasting* protection and performance.

Interior stops are unfinished clear pine. Low- maintenance prefinished white interiors are also available. Choose either painted or vinyl-wrapped options.

SaSH

Rigid vinyl (PVC) encases the entire sash. A vinyl weld protects each sash corner to help prevent moisture penetration, maintain an attractive appearance and minimize maintenance.

Natural wood core members provide excellent structural stability and energy efficiency.

Flexible bulb weatherstripping or black PVC closed-cell foam weatherstripping is factory-installed on the perimeter of the sash.

Additional screws have been added to

each window hinge.

A hinge-side sash stiffener bar has been added to

the frame of C55 and C6 height windows. On non-venting windows, the sash is held in place with sash clips that use screws instead of standard staples, providing the rigid frame and sash connection that is needed to withstand greater design pressures.

GlaSS

A non-corrosive rigid vinyl or CPVC glazing bead features a flexible lip that, combined with silicone glazing, provides increased weathertightness.

Silicone is applied to the full perimeter of the glass

on the interior side of the pane to add strength and stability.

Consult local building codes for glass most

suitable to your area. Glass options include:

• Standard High-Performance™ Low-E4® glass (PG Upgrade)

• Standard High-Performance™ Low-E4® Sun glass (PG Upgrade)

• Standard High-Performance™ Low-E4® SmartSun™ glass (PG Upgrade)

• High-Performance™ Low-E4® impact-resistant glass

• High-Performance™ Low-E4® Sun impact-resistant glass

• High-Performance™ Low-E4® SmartSun™ impact-resistant glass

• High-Performance™ Low-E4® tempered impact-resistant glass

• High-Performance™ Low-E4® Sun tempered impact-resistant glass

• High-Performance™ Low-E4® SmartSun™ tempered impact-resistant glass

• Monolithic impact-resistant glass

• Monolithic tinted impact-resistant glass

Available in white or stone finish.

Folding handle avoids interference with window decorating treatments.

ContemporaryAvailable in bright brass, satin nickel,

oil rubbed bronze, white, stone, gold dust and black finish.

TraditionalAvailable in bright brass, antique brass, satin nickel, oil rubbed bronze, white,

stone, gold dust and black finish.

exterior Interior

pinewhite

Naturally occurring variations in grain, color and texture make each window one-of-a-kind.

Specify a unit exterior color option and an interior finish option to complete your order. Andersen® 400 Series casement windows are available with prefinished white interior stops.

brightbrass

antiquebrass

polishedchrome

brushedchrome

satinnickel

oilrubbedbronze

distressednickel

distressedbronze

white goldduststone black

Hardware Finishes

Printing limitations prevent exact color duplication.

See your Andersen supplier for actual color samples.

SpecIal USe OpeRatORS Andersen Classic Series™ design only. Andersen remote power operators cannot be used with awnings with Stormwatch® protection.

Compact Operator HandleSpecially designed for use in situations where blinds or other window treatments interfere with standard operator handle. Available in white or stone finish.

Metal T-HandleOur smallest operator, the metal T-handle may make it more difficult for young children (5 and under) to open the window. For more information on child safety, write:

Andersen Corporation LookOut for Kids® Program100 Fourth Avenue North Bayport, MN 55003

Call 1-800-313-8889 or Email us at: [email protected]

Operator Spline CoverAn operator spline cover is an attractive cap that covers the roto operator stud when the handle has been removed to control access or operation of the window. Operator spline cover should not be used on any window designated or intended for emergency escape or rescue. Please consult your local building code official for local egress code requirements.

Classic Series™ Hardware


11

CAUTION: • Painting and staining may

cause damage to rigid vinyl. • Products in Sandtone or Terratone®

color may be painted any color lighter than Terratone using quality oil-base or latex paint. Submit color samples to Andersen for approval when painting White. Submit color samples to Andersen for approval when painting Sandtone or Terratone any color darker than Terratone.

• Do not paint Forest Green exteriors.• Creosote-based stains should

not come in contact with Andersen products.

• Do not paint weatherstripping. • Abrasive cleaners or solutions

containing corrosive solvents should not be used on Andersen products.

• For vinyl painting instructions and preparation, contact your Andersen supplier.

• Andersen does not warrant the adhesion of paint to vinyl.

accessories Sold Separately.

Drywall Return BeadA drywall return bead is available for units ordered with prefinished white interiors. Can be ordered factory-applied or in non-applied lineals.

HaRdwaRe

Optional Corrosion- Resistant HardwareHardware components include high-quality, stainless-steel, corrosion-resistant hinges, screws and operator. For harsh and corrosive environment applications such as heavy industrial or coastal areas.*

GlaSSAndersen® Art GlassAndersen art glass panels come in eleven original patterns, including four Frank Lloyd Wright ® series designs. See the Andersen® Product Guide for details on Andersen art glass, or visit andersenwindows.com/artglass for pattern information.

InSect ScReenS

TruScene® Insect ScreenTruScene insect screens provide over 50% more clarity than our conventional insect screens. For casement and awning windows. Available with stone or white colored frames or pine interiors to blend with the windows that surround them.

Conventional Insect ScreenConventional Perma-Clean® insect screens are available with frames finished in white and stone.

FRame

Extension JambsStandard casement/awning jamb depth is 2-7/8" (83). Extension jambs are available for a variety of wall depths. Some sizes may be pine veneer.

Non-Applied Extension JambsPine extension jambs are available for the following wall thicknesses:

• 4-9/16" (116) • 5-1/4" (133) • 6-9/16" (167) • 7-1/8" (181)

Extension jambs are pre-drilled in the following width:

• 6-9/16" (167)

All sizes are available unfinished or with a low-maintenance vinyl wrapped white finish.

Factory-Applied Extension JambsAvailable in 4-9/16" (116) and 6-9/16" (167) sizes. They can be applied to either three sides (stool and apron applications) or four sides (picture frame casing). Ask your Andersen supplier for details.

InStallatIOn SyStem

The installation system includes 1-1/2" (38)

by 3" (76) stainless steel installation clips for additional reinforcement. The installation clips are screwed to the frame and fastened to the rough opening for secure installation. Optional 6" clips are available for use with factory-applied or pre-applied extension jambs.

Awning Sash Locks

Awning sash locks provide an added measure of security and weathertightness.

pG UpGRadeS

Casement and Awning WindowsPG Upgrades are available for select sizes only. Ask your Andersen® supplier for details.

* See the limited warranty for details.“Frank Lloyd Wright” is a registered trademark of the Frank Lloyd Wright Foundation.

Easy-Grip HandleLarger knob makes it easier to grip and operate. Available in white or stone finish.

exclUSIve

Learn more online at andersenwindows.com

400

C

asem

ent&

Awni

ngW

indo

ws

12

Casement & Awning WindowsTable of Basic Casement Unit Sizes Scale 1/8" = 1'-0" (1:96)

Venting Conguration Hinging shown on size table is standard. Specify left, right or stationary, as viewed from the outside. For other hinging of multiple units, contact your local supplier.

Left

Right

Stationary

4'-8 1/2"

4'-9"

24"

4'-0"

4'-0 1/2"

19 3/4"

3'-4 3/4"

3'-5 1/4"

16 1/8"

2'-9 3/4"

2'-10 1/4"

12 5/8"

2'-4 3/8"

2'-4 7/8"

24"

2'-7 1/2"

2'-8"

2'-0 1/8"

2'-0 5/8"

19 3/4"

5'-1

1 7 /

8"

6'-0

3/ 8

"

67 1

/ 16"

4'-1

1 7 /

8"

5'-0

3/ 8

"

55 1

/ 16"

4'-0

"

4'-0

1/ 2

"

43 3

/ 16"

3'-4

13 /

16"

3'-5

3/ 8

"

36"

2'-1

1 15

/ 16"

3'-0

1/ 2

"

31 1

/ 8"

4'-4

13 /

16"

4'-5

3/ 8

"

48"

5'-4

13 /

16"

5'-5

3/ 8

"

60"

Unit Dimension

Unobstructed Glass*

2'-0

1 /8"

2'-0

5 /8"

1'-

0 1 /

2"

19 5 /

16"

1-0"

7 3 /

16"

23 9

/ 16"

2'-4

3/ 8

"

2'-4

7 /8"

2'-1115/16"

3'-0 1/2"

31 9/16" 27 1/8"

43 3/16" 51 11/16"35 15/16" 28 15/16" 19 5/16"Unobstructed GlassTransom Units Only

To �nd compatible Circle Top,™ arch and other shaped windows, see the specialty window section beginning on page 33.

31 1/8"26 11/16"23 9/16"

(613)

(625)

(502)

(721)

(733)

(610)

(800)

(813)

(689)

(857)

(870)

(321)

(1035)

(1048)

(410)

(1219)

(1232)

(502)

(1435)

(1448)

(610)

(613

)

(625

)

(491

)

(305

)

(318

)

(183

)

1'-0

1 /2"

1-0"

7 3 /

16"

(305

)

(318

)

(183

)

(913

)

(927

)

(791

)

(103

7)

(105

1)

(914

)

(121

9)

(123

2)

(109

7)

(134

1)

(135

6)

(121

9)

(152

1)

(153

4)

(139

9)

(164

6)

(166

0)

(152

4)

(182

6)

(183

8)

(170

3)

(721

)

(733

)

(598

)(913)

(927)

(802)

(491) (599) (678) (735) (913) (1097) (1313)(791)

CXW13

CXW14

CXW135

CXW145

CN16CR16 C16 CW16†

CN155

CN15

CN145

CR155

CR15

CR145

CW155†C155

CW145†

C15

C145

CW15†

CN14

CN135

CN13

CN125

CR135

CR14

CR13

CR125

CW135†C135

CW14†C14

CW125

C13

C125

CW13

CN12CR12 C12 CW12

CN26 CW26†C26

C255

C245

CN25 CW25†C25

C235CN235CR235

CR24 CN24

CR23 CN23

CW235†

CW24†C24

CW23

CTR units are non-venting.

C23

CX125

CR26

CR255 CN255

CR25

CW255†

CW245†CR245 CN245

CX13

CX14

CX135**

CX145

CX15

CX155

CX16

CTR3010 ‡CTR2010 ‡ CTR2410 ‡ CTR2910 ‡ CTR3410 ‡ CTR4810 ‡CTR4010 ‡CTR2810 ‡

1'-8 1/2"

1'-9"

16 1/8"

1'-5"

1'-5 1/2"

12 5/8"

15 11/16" 12 3/16"

(432)

(445)

(321)

(521)

(533)

(410)

(310) (398)

CTR1810 ‡CTR1510 ‡

MinimumRough Opening

* “Unobstructed Glass” measurement is for single sash only.** These units have straight arm operators, see opening speci�cations.† CW series units open to 20" clear opening width using sill hinge control bracket. Bracket can be pivoted allowing for cleaning position. CW series units

are also available with a 22" clear opening width.‡ Andersen® art glass panels are available for these units by special order only. Contact your Andersen® supplier. Panels are available for all other units

on this page through normal ordering process. These units meet or exceed the following dimensions: Clear Openable Area of 5.7 sq. ft., Clear Openable Width of 20" and Clear Openable Height of

24", when appropriate hardware (straight arm or split arm) is speci�ed.• Casement transom units (CTR) may be rotated to be used as a casement or awning sidelight.• Rough opening dimensions may need to be increased to allow for use of building wraps, �ashing, sill panning, brackets, fasteners or other items.

See page 7 for more details.• “Unit Dimension” always refers to outside frame to frame dimension.• Dimensions in parentheses are in millimeters.• When ordering, be sure to specify color desired: White, Sandtone, Terratone® or Forest Green.

CN225 CW225

CW22CN22

CTR21810 CTR22010 CTR22410

C225

C22

Custom sizes available. Some restrictions apply. Contact your Andersen supplier for availability.

Custom Sizes

13

Basic Unit and Rough Opening Details Scale 1-1/2" = 1'-0" (1:8)

• Casement transom units (CTR) may be rotated to be used as a casement or awning sidelight.

• Rough opening dimensions may need to be increased to allow for use of building wraps, �ashing, sill panning, brackets, fasteners or other items. See page 7 for more details.

• Note: Floor to sill heights are calculated based upon a structural header height of 6'-10 1/2".

• Light colored areas are basic parts furnished by Andersen. Dark colored areas are recommended Andersen parts to complete unit assembly and must be speci�cally ordered.

5'-1"

5'-1 1/2"

16 1/8"

5'-11 7/8"

6'-0 3/8"

19 3/4"

56 3/16" 67 1/16"

(1549)

(410)

(1562)

(1826)

(502)

(1838)

(1427) (1703)

C35

C335

C34

C33

C345

CTR6010 ‡

2-7/8"(73)

1-5/16"(33)

Min

. Rou

gh O

peni

ng H

eigh

t

Unit

Dim

ensi

on H

eigh

t

Clea

r Opg

.He

ight

2-3/

8"(6

0)2-

5/8"

(67)

1-1/8"(29)

1-7/16"(37)

Sill Stopto Sub oorDimension

4-9/16" (116)Jamb Width*

1-1/8" (29)

1-3/16" (30)

Extension jamb

Insect screen

Monolithicimpact resistant glassHead

Sill

Vertical SectionMonolithic Impact-Resistant Glass Horizontal Section

High-Performance™ Low-E4® Impact-Resistant Glass

Clear Opening Width

Sash Projection14-1/4" (362)17-3/4" (451)21-3/8" (543)25-5/8" (651)28-3/4" (730)33-3/16" (843)

JambJamb

For CR, CN, C, CX125 through CX16 and CXW13 through CXW145 units with split arm operator, and for C, CW, CX and CXW units with straight arm operator in full open position.

Clear Opening Width

(for CW units, split a

rm

operator, in

full open positio

n)

* measurement is from backside of anchoring ange to edge of extension jamb.

CN33

CN35

CN335

CN34

CN345

CTR5110 ‡

CN325

CN32

CTR31810 CTR32010

Reinforced Joining Details Scale 1-1/2" = 1'-0" (1:8)

Andersen® Steel Reinforced Mullion

Casement units joined using Andersen steel reinforced joining materials. For applications that require reinforcement for lateral loads. Andersen reinforced joining materials can be used for mullion and transom joining.

Support Mullion

Casement units joined using standard 2" x 4" or 2" x 6" wood joining materials (supplied by others). For applications that require reinforcement for lateral loads. Andersen support mullion trim is used to provide a beautiful, durable �nish trim that is compatible with Andersen® product materials and colors.

Casement to Casement Support Mullion

Overall Unit Dimension Width:

Sum of individual Unit Dimension Widths, plus 2" (51mm) for each unit joining.

Overall Rough Opening Width:

Add 1/2" (13mm) to Overall Unit Dimension Width.

Andersen® LVL Reinforced Mullion

Casement units joined using Andersen LVL (Laminated Veneer Lumber) reinforced joining materials. For applications that require reinforcement for lateral loads. Andersen LVL reinforced joining materials can be used for mullion and transom joining.

Andersen® Aluminum Reinforced Mullion

Casement units joined using Andersen aluminum reinforced joining materials. For applications that require reinforcement for lateral loads. Andersen aluminum reinforced joining materials can be used for mullion and transom joining.

NOTE: For two-way combinations exceeding 42 sq. ft., aluminum, steel or LVL reinforced joining materials must be used.For smaller combinations, refer to the Combination Design section to determine if reinforcement is necessary.

1/8" (3)

2-3/8" (60)

Unit Dim. Width Unit Dim. Width

Andersen®casing for steel

Sealant andexterior trim strip

Andersen steel reinforcednarrow mullion

1/8" (3)

2-3/8" (60)

Andersenaluminum reinforcednarrow mullion

Sealant andexterior trim strip

3/4" (19)

2-7/8" (73)

Andersenextension jambs

OptionalAndersen® casing

Andersen LVL mullion

Unit Dim. Width Unit Dim. Width Unit Dim. Width Unit Dim. Width

2" (51)


2" (51)

2x4

Casing by others

Structure by others


Optional Andersen®

wood �ller and vinyl trim


Casing by others

Structure by others


Optional Andersen®

wood �ller and vinyl trim

C325

C32

2x6

400

C

asem

ent&

Awni

ngW

indo

ws

14


1-1/8" (29) 2-5/16" (59)1-3/16" (30)

Minimum Rough Opening Width

Unit Dimension Width

Jamb Jamb

Extension jamb

1/4"(6)

1/4"(6)

1-5/16"(33)

2-7/

8"(7

2)

4-9/

16"

(116

)Ja

mb

Wid

th*

Clear Opg. Width

High-Performance™ Low-E4®

impact-resistant glass

Horizontal SectionHigh-Performance™ Low-E4® Impact-Resistant Glass

Table of Basic Awning Unit Sizes Scale 1/8" = 1'-0" (1:96)

Venting Con�guration Venting Stationary

Unit Dimension

Unobstructed Glass

2'-0 1/8"

2'-0 5/8"

19 5/16"

2'-11 15/16"

3'-0 1/2"

31 1/8"

3'-4 13/16"

3'-5 3/8"

36"

4'-0"

4'-0 1/2"

43 3/16"

1'-8

1/ 2

"

1'-9

"

16 1 /

8"

2'-0

1/ 8

"

2'-0

5 /8"

19 3

/ 4"

2'-4

3/ 8

"

2'-4

7/ 8

"

24"

1'-5

"

1'-5

1 /2"

12 5

/ 8"

4'-5 3/8"

48"

4'-4 13/16"

5'-0 3/8"

4'-11 7/8"

55 1/16"23 9/16"

2'-4 3/8"

2'-4 7/8"

2'-7 1/2"

2'-8"

27 1/8"


(1219)

(1232)

(1097)

(1037)

(1051)

(914)

(913)

(927)

(791)

(613)

(625)

(491)

(721

)

(733

)

(610

)

(613

)

(625

)

(502

)

(432

)

(445

)

(321

)

(521

)

(533

)

(410

)

(1341)

(1356)

(1219)

(1521)

(1534)

(1399)

(721)

(733)

(598)

AN31

A21 A31

AN351

A351

AN41

A41

AW31 AW41

AR21 AR31 AR351 AR41

AW21 AW351

AN21

A451 A51

AN51

AR51

AW51

AN451

AW451

AX31 AX41AX351 AX51AX451

AR451

A251

AR251

AN251

AW251

AX251 AX281 ‡

2'-7

1/ 2

"

2'-8

"

27 1

/ 8"

(800

)

(813

)

(689

)

(800)

(813)

(689)

A281 ‡

AR281 ‡

AN281 ‡

AW281 ‡



‡ Andersen® art glass panels are available for these units by special order only. Contact your Andersen® supplier. Panels are available for all other units on this page, except where noted, through normal ordering process.• Rough opening dimensions may need to be increased to allow for use of building wraps, �ashing, sill panning, brackets, fasteners or other items. See page 7 for more details. • Dashed lines on size tables indicate hinging (also available as stationary units).• Stationary units are available as venting units by special order. Some restrictions may apply. Contact your local Andersen® Supplier.• “Unit Dimension” always refers to outside frame to frame dimension.• Dimensions in parentheses are in millimeters.• When ordering, be sure to specify color desired: White, Sandtone, Terratone® or Forest Green.

Vertical SectionMonolithic Impact-Resistant Glass

4-9/16" (116)Jamb Width*2-7/8" (73)

1-5/16" (33)

Min

imum

Rou

gh O

peni

ng H

eigh

t

Unit

Dim

ensi

on H

eigh

t 1-1/8" (29)15/16" (17)

Sill Stop toSub�oorDimension

Extension jamb

Head

Sill

ClearOpeningHeight

1-1/8" (29)1-1/8" (29)

1/4" (6)

Insect screen

Monolithic impact-resistant glass

1'-8

1⁄ 2

"

1'-9

"

2'-0

1⁄ 8"

2'-0

5⁄ 8"

2'-4

3⁄ 8"

2'-4

7⁄ 8"

1'-5

"

1'-5

1⁄ 2

"

(721

)

(733

)

(613

)

(625

)

(432

)

(445

)

(521

)

(533

)

2'-7

1⁄ 2

"

2'-8

"

(800

)

(813

)

2'-0 1 ⁄ 8"

2'-0 5 ⁄ 8"

2'-11 15 ⁄16"

3'-0 1 ⁄ 2"

(913)

(927)

(613)

(625)

A312

AR231 AR3251AR321AR2281AR2251AR221

AN231 AN3251AN321AN2281AN2251AN221

A231 A3251A321A2281A2251A221

AW231 AW3251AW321AW2281AW2251AW221

AX231 AX3251AX2281AX2251

A212(A21/A21)

A213 A313

4'-8 1 ⁄ 2"

4'-9"

4'-0"

4'-0 1 ⁄ 2"

5'-1

1 7⁄ 8"

6'-0

3⁄ 8"

4'-0

"

4'-0

1⁄ 2

"

(1219)

(1232)

(1435)

(1448)

(121

9)

(123

2)

(182

6)

(183

8)

5'-11 5 ⁄ 8"

6'-0 1 ⁄ 8"

5'-2 3 ⁄4"

5'-3 1 ⁄4"

5'-11 7⁄ 8"

6'-0 3 ⁄ 8"

7'-0 5 ⁄ 8"

7'-1 1 ⁄ 8"

(1819)

(1832)

(1594)

(1607)

(1826)

(1838)

(2149)

(2162)

16 1

⁄ 8"19

3⁄ 4"

24"

12 5

⁄ 8"(6

10)

(502

)(3

21)

(410

)27

1⁄ 8"

(689

)

Unit Dimension

Unobstructed Glass*


31 1 ⁄ 8"(791)

19 5 ⁄16"(491)

19 5 ⁄16"(491)

23 9 ⁄16"(598)

23 9 ⁄16"(598)

27 1 ⁄ 8"(689)

(A31/A31)

(A21/A21/A21) (A31/A31/A31)

* 4-9/16" measurement is from backside of anchoring �ange to edge of extension jamb.

NOTE: See more installation information starting on page 6.

CAUTION: In masonry wall contruction, provided a minimum of 1/2” clearance from the top of the brick or masonry to the bottom of any portion of the sill. Failure to do so could result in product damage. Fill the void with closed cell foam backer rod and sealant. Be sure to allow for dimensional change of framework.

Custom sizes available. Some restrictions apply. Contact your Andersen supplier for availability.

Custom Sizes

15

Table of Picture Unit Sizes Scale 1/8" = 1'-0" (1:96)

Picture Unit and Rough Opening Details Scale 1-1/2" = 1'-0" (1:8)

‡ Andersen® art glass panels are available for these units by special order only. Contact your Andersen® supplier. Panels are available for all other units on this page through normal ordering process.


• Dimensions in parentheses are in millimeters.• When ordering, be sure to specify color desired: White, Sandtone, Terratone®

or Forest Green.• PICTURE UNITS may be rotated in either direction to align with casement or

awning windows (as illustrated by label on glass).

6'-0 3/8"

5'-11 7/8"

67 1/16"

3'-4 13/16"

3'-5 3/8"

36"

4'-0"Unit Dimension

5'-0 3/8"

4'-11 7/8"67

1/ 1

6"

5'-1

1 7 /

8"

6'-0

3/ 8

"

4'-0

"

4'-0

1/ 2

"

43 3

/ 16"

2'-1

1 15

/ 16"

3'-0

1/ 2

"

55 1

/ 16"

4'-1

1 7 /

8"

5'-0

3/ 8

"

31 1

/ 8"

3'-5

3/ 8

"

36"

4'-4

13 /

16"

4'-5

3/ 8

"

48"

5'-4

13 /

16"

5'-5

3/ 8

"

60"

Unobstructed Glass

4'-0 1/2"

43 3/16" 55 1/16"

3'-4

13/ 1

6"

2'-11 15/16"

3'-0 1/2"

31 1/8" 48"

4'-4 13/16"

4'-5 3/8"

60"

5'-4 13/16"

5'-5 3/8"(1826)

(1838)

(1703)

(1219)

(1232)

(1097)

(1037)

(1051)

(914)

(1521)

(1534)

(1399)

(182

6)

(183

8)

(170

3)

(121

9)

(123

2)

(109

7)

(913

)

(927

)

(152

1)

(153

4)

(139

9)(7

91)

(103

7)

(105

1)

(914

)

(134

1)

(135

6)

(121

9)

(164

6)

(166

0)

(152

4)(913)

(927)

(791)

(1341)

(1356)

(1219)

(1646)

(1660)

(1524)

P3030

P3035

P3040

P3045

P3050

P3055

P3060

P3530

P3535

P3540

P3545

P3550

P3555

P3560

P4030

P4035

P4040

P4045

P4050

P4055 ‡

P4060 ‡

P4530

P4535

P4540

P4545 ‡

P4550 ‡

P4555 ‡

P4560 ‡

P5030

P5035

P5040

P5045 ‡

P5050 ‡

P5530

P5535

P5540 ‡

P5545 ‡

P5550 ‡

P6030

P6035

P6040 ‡

P6045 ‡

P6050 ‡

P5055 ‡

P5060 ‡

1'-0

1 /2"

1-0"

7 3 /

16"

(305

)

(318

)

(183

)

PTR3010 ‡ PTR4010 ‡ PTR5010 ‡PTR4510 ‡PTR3510 ‡ PTR5510 ‡ PTR6010 ‡


* 4-9/16" measurement is from backside of anchoring �ange to edge of extension jamb.

2-3/8"(60)

2-3/8"(60)

Glass Width



1/4" (6) 1/4" (6)

JambJamb

4-9/

16"

(116

) Ja

mb

Wid

th*

1-5/16" (33)

2-7/8" (72)

1-1/8"(29)

1-3/16"(30)

1-1/8" (29)

1-3/16" (30)

2-3/

8"(6

0)2-

3/8"

(60)

Glas

sW

idth

Unit

Dim

ensi

on W

idth

Min

imum

Rou

gh O

peni

ng W

idth

1/4" (6)

1/4" (6)

Head

Extension jamb

4-9/16" (116) Jamb Width*

1-5/16" (33)

2-7/8" (72)

SillVertical Section

High-Performance™ Low-E4® Impact-Resistant GlassHorizontal Section

Monolithic Impact-Resistant Glass


Monolithic Impact-Resistant Glass

400

C

asem

ent&

Awni

ngW

indo

ws

16

Casement & Awning WindowsCasement Window Opening Specifications

Unit Number

Clear Opg. Straight Arm

Sq. Ft. (m2)

Clear Opg. Split Arm

Sq. Ft. (m2)

Clear Opening in Full Open Position

GlassSq. Ft. (m2)

Crack Opening Vent Sash Only

Lineal Ft. (mm)

Straight Arm Vent

Sq. Ft. (m2)

Split Arm Vent

Sq. Ft. (m2)

Top of Subfloor to Top of Inside

Sill Stop Inches (m2)

Overall Unit Area

Sq. Ft. (m2)

Straight Arm WidthInches (mm)

Split Arm WidthInches (mm)

Height

Inches (mm)

CR12 — — 1.0 (0.093) — — 7-5/16" (186) 19-1/4" (489) 1.7 (0.158) 6' 4-13/16" (1951) — — 1.5 (0.139) 60-9/16" (1538) 2.8 (0.260)CR125 — — 1.2 (0.111) — — 7-5/16" (186) 23-7/16" (595) 2.0 (0.186) 7' 0-15/16" (2157) — — 1.8 (0.167) 56-3/8" (1432) 3.3 (0.307)CR13 — — 1.6 (0.149) — — 7-5/16" (186) 31-1/16" (789) 2.7 (0.251) 8' 4-7/16" (2551) — — 2.4 (0.223) 48-3/4" (1238) 4.2 (0.390)CR135 — — 1.8 (0.167) — — 7-5/16" (186) 35-15/16" (913) 3.1 (0.288) 9' 2-3/16" (2799) — — 2.7 (0.251) 43-7/8" (1114) 4.8 (0.446)CR14 — — 2.2 (0.204) — — 7-5/16" (186) 43-1/8" (1095) 3.8 (0.353) 10' 4-9/16" (3164) — — 3.3 (0.307) 36-11/16" (932) 5.7 (0.530)CR145 — — 2.4 (0.223) — — 7-5/16" (186) 47-15/16" (1218) 4.2 (0.390) 11' 2-3/16" (3408) — — 3.6 (0.334) 31-7/8" (810) 6.2 (0.576)CR15 — — 2.8 (0.260) — — 7-5/16" (186) 55" (1397) 4.8 (0.446) 12' 4-5/16" (3767) — — 4.2 (0.390) 24-13/16" (630) 7.1 (0.660)CR155 — — 3.1 (0.288) — — 7-5/16" (186) 59-15/16" (1522) 5.2 (0.483) 13' 2-3/16" (4018) — — 4.5 (0.418) 19-7/8" (505) 7.7 (0.715)CR16 — — 3.4 (0.316) — — 7-5/16" (186) 67" (1702) 5.9 (0.548) 14' 4-5/16" (4377) — — 5.1 (0.474) 12-13/16" (325) 8.5 (0.790)CR23 — — 1.6 (0.149) — — 7-5/16" (186) 31-1/16" (789) 5.4 (0.502) 16' 8-7/8" (5102) — — 4.7 (0.437) 48-3/4" (1238) 8.4 (0.780)CR235 — — 1.8 (0.167) — — 7-5/16" (186) 35-15/16" (913) 6.3 (0.585) 18' 4-3/8" (5598) — — 5.4 (0.502) 43-7/8" (1114) 9.6 (0.892)CR24 — — 2.2 (0.204) — — 7-5/16" (186) 43-1/8" (1095) 7.6 (0.706) 20' 9-1/8" (6328) — — 6.5 (0.604) 36-11/16" (932) 11.3 (1.050)CR245 — — 2.4 (0.223) — — 7-5/16" (186) 47-15/16" (1218) 8.4 (0.780) 22' 4-3/8" (6817) — — 7.3 (0.678) 31-7/8" (810) 12.4 (1.152)CR25 — — 2.8 (0.260) — — 7-5/16" (186) 55" (1397) 9.6 (0.892) 24' 8-5/8" (7534) — — 8.3 (0.771) 24-13/16" (630) 14.2 (1.319)CR255 — — 3.1 (0.288) — — 7-5/16" (186) 59-15/16" (1522) 10.5 (0.975) 26' 4-3/8" (8036) — — 9.1 (0.845) 19-7/8" (505) 15.4 (1.431)CR26 — — 3.4 (0.316) — — 7-5/16" (186) 67" (1702) 11.7 (1.087) 28' 8-5/8" (8753) — — 10.2 (0.948) 12-13/16" (325) 17.0 (1.579)CN12 — — 1.5 (0.139) — — 10-13/16" (275) 19-1/4" (489) 2.2 (0.204) 6' 11-13/16" (2129) — — 1.9 (0.177) 60-9/16" (1538) 3.4 (0.316)CN125 — — 1.8 (0.167) — — 10-13/16" (275) 23-7/16" (595) 2.6 (0.242) 7' 7-15/16" (2335) — — 2.3 (0.214) 56-3/8" (1432) 4.0 (0.372)CN13 — — 2.3 (0.214) — — 10-13/16" (275) 31-1/16" (789) 3.5 (0.325) 8' 11-7/16" (2729) — — 3.1 (0.288) 48-3/4" (1238) 5.1 (0.474)CN135 — — 2.7 (0.251) — — 10-13/16" (275) 35-15/16" (913) 4.0 (0.372) 9' 9-3/16" (2977) — — 3.6 (0.334) 43-7/8" (1114) 5.8 (0.539)CN14 — — 3.2 (0.297) — — 10-13/16" (275) 43-1/8" (1095) 4.8 (0.446) 10' 11-9/16" (3342) — — 4.3 (0.399) 36-11/16" (932) 6.8 (0.632)CN145 — — 3.6 (0.334) — — 10-13/16" (275) 47-15/16" (1218) 5.4 (0.502) 11' 9-3/16" (3586) — — 4.8 (0.446) 31-7/8" (810) 7.5 (0.697)CN15 — — 4.1 (0.381) — — 10-13/16" (275) 55" (1397) 6.2 (0.576) 12' 11-5/16" (3945) — — 5.5 (0.511) 24-13/16" (630) 8.5 (0.790)CN155 — — 4.5 (0.418) — — 10-13/16" (275) 59-15/16" (1522) 6.7 (0.622) 13' 9-3/16" (4196) — — 6.0 (0.557) 19-7/8" (505) 9.2 (0.855)CN16 — — 5.0 (0.465) — — 10-13/16" (275) 67" (1702) 7.5 (0.697) 14' 11-5/16" (4555) — — 6.7 (0.622) 12-13/16" (325) 10.2 (0.948)CN22 — — 1.5 (0.139) — — 10-13/16" (275) 23-7/16" (595) 5.2 (0.484) 15' 3-7/8" (4670) — — 4.6 (0.428) 56-6/16" (1432) 8.0 (0.744)CN225 — — 1.8 (0.167) — — 10-13/16" (275) 19-1/4" (489) 4.4 (0.408) 13' 11-5/8" (4258) — — 3.8 (0.354) 60-9/16" (1538) 6.8 (0.632)CN23 — — 2.3 (0.214) — — 10-13/16" (275) 31-1/16" (789) 7.0 (0.650) 17' 10-7/8" (5458) — — 6.2 (0.576) 48-3/4" (1238) 10.2 (0.948)CN235 — — 2.7 (0.251) — — 10-13/16" (275) 35-15/16" (913) 8.0 (0.743) 19' 6-3/8" (5953) — — 7.2 (0.669) 43-7/8" (1114) 11.5 (1.068)CN24 — — 3.2 (0.297) — — 10-13/16" (275) 43-1/8" (1095) 9.7 (0.901) 21' 11-1/8" (6683) — — 8.6 (0.799) 36-11/16" (932) 13.6 (1.263)CN245 — — 3.6 (0.334) — — 10-13/16" (275) 47-15/16" (1218) 10.7 (0.994) 23' 6-3/8" (7172) — — 9.6 (0.892) 31-7/8" (810) 15.0 (1.394)CN25 — — 4.1 (0.381) — — 10-13/16" (275) 55" (1397) 12.3 (1.143) 25' 10-5/8" (7890) — — 11.0 (1.022) 24-13/16" (630) 16.9 (1.570)CN255 — — 4.5 (0.418) — — 10-13/16" (275) 59-15/16" (1522) 13.4 (1.245) 27' 6-3/8" (8392) — — 12.0 (1.115) 19-7/8" (505) 18.4 (1.709)CN26 — — 5.0 (0.465) — — 10-13/16" (275) 67" (1702) 15.0 (1.394) 29' 10-5/8" (9109) — — 13.4 (1.245) 12-13/16" (325) 20.3 (1.886)CN32 — — 1.5 (0.139) — — 10-13/16" (275) 19-1/4" (489) 6.6 (0.612) 13' 11-5/8" (4258) — — 3.8 (0.354) 60-9/16" (1538) 10.2 (0.948)CN325 — — 1.8 (0.167) — — 10-13/16" (275) 23-7/16" (595) 7.8 (0.726) 15' 3-7/8" (4670) — — 4.6 (0.428) 56-3/8" (1432) 12.0 (1.116)CN33 — — 2.3 (0.214) — — 10-13/16" (275) 31-1/16" (789) 10.5 (0.975) 17' 10-7/8" (5458) — — 6.2 (0.576) 48-3/4" (1238) 15.3 (1.422)CN335 — — 2.7 (0.251) — — 10-13/16" (275) 35-15/16" (913) 12.0 (1.116) 19' 6-3/8" (5954) — — 7.2 (0.668) 43-7/8" (1114) 17.4 (1.617)CN34 — — 3.2 (0.297) — — 10-13/16" (275) 43-1/8" (1095) 14.4 (1.338) 21' 11-1/8" (6684) — — 8.6 (0.798) 36-11/16" (932) 20.4 (1.896)CN345 — — 3.6 (0.334) — — 10-13/16" (275) 47-15/16" (1218) 16.2 (1.506) 23' 6-3/8" (7172) — — 9.6 (0.892) 31-7/8" (810) 22.5 (2.091)CN35 — — 4.1 (0.381) — — 10-13/16" (275) 55" (1397) 18.6 (1.728) 25' 10-5/8" (7890) — — 11.0 (1.022) 24-13/16" (630) 25.5 (2.370)C12 2.5 (0.232) 1.9 (0.177) 18-5/16" (465) 14-7/16" (367) 19-1/4" (489) 2.6 (0.242) 7' 7-1/16" (2313) 2.5 (0.232) 2.4 (0.223) 60-9/16" (1538) 4.0 (0.372)C125 3.0 (0.279) 2.4 (0.223) 18-5/16" (465) 14-7/16" (367) 23-7/16" (595) 3.2 (0.297) 8' 3-3/16" (2519) 3.0 (0.279) 2.9 (0.269) 56-3/8" (1432) 4.7 (0.437)C13 4.0 (0.372) 3.1 (0.288) 18-5/16" (465) 14-7/16" (367) 31-1/16" (789) 4.3 (0.399) 9' 6-11/16" (2913) 4.0 (0.372) 3.9 (0.362) 48-3/4" (1238) 6.0 (0.557)C135 4.6 (0.427) 3.6 (0.334) 18-5/16" (465) 14-7/16" (367) 35-15/16" (913) 4.9 (0.455) 10' 4-7/16" (3161) 4.6 (0.427) 4.5 (0.418) 43-7/8" (1114) 6.8 (0.632)C14 5.5 (0.511) 4.3 (0.399) 18-5/16" (465) 14-7/16" (367) 43-1/8" (1095) 5.9 (0.548) 11' 6-13/16" (3526) 5.5 (0.511) 5.4 (0.502) 36-11/16" (932) 8.0 (0.743)C145 6.1 (0.567) 4.8 (0.446) 18-5/16" (465) 14-7/16" (367) 47-15/16" (1218) 6.6 (0.613) 12' 4-7/16" (3770) 6.1 (0.567) 6.0 (0.557) 31-7/8" (810) 8.8 (0.818)C15 7.0 (0.650) 5.5 (0.511) 18-5/16" (465) 14-7/16" (367) 55" (1397) 7.5 (0.697) 13' 6-9/16" (4129) 7.0 (0.650) 6.9 (0.641) 24-13/16" (630) 10.0 (0.929)C155 7.6 (0.706) 6.0 (0.557) 18-5/16" (465) 14-7/16" (367) 59-15/16" (1522) 8.2 (0.762) 14' 4-7/16" (4380) 7.6 (0.706) 7.5 (0.697) 19-7/8" (505) 10.9 (1.013)C16 8.5 (0.790) 6.7 (0.622) 18-5/16" (465) 14-7/16" (367) 67" (1702) 9.2 (0.855) 15' 6-9/16" (4739) 8.5 (0.790) 8.4 (0.780) 12-13/16" (325) 12.0 (1.115)C22 2.5 (0.232) 1.9 (0.177) 18-5/16" (465) 14-7/16" (367) 19-1/4" (489) 5.2 (0.484) 15' 2-1/8" (4626) 5.0 (0.464) 4.8 (0.446) 60-9/16" (1538) 8.0 (0.744)C225 3.0 (0.279) 2.4 (0.223) 18-5/16" (465) 14-7/16" (367) 23-7/16" (595) 6.4 (0.594) 16' 6-3/8" (5038) 6.0 (0.558) 5.8 (0.538) 56-3/8" (1432) 9.4 (0.874)C23 4.0 (0.372) 3.1 (0.288) 18-5/16" (465) 14-7/16" (367) 31-1/16" (789) 8.5 (0.790) 19' 1-3/8" (5826) 7.9 (0.734) 7.8 (0.725) 48-3/4" (1238) 12.0 (1.115)C235 4.6 (0.427) 3.6 (0.334) 18-5/16" (465) 14-7/16" (367) 35-15/16" (913) 9.9 (0.920) 20' 8-7/8" (6321) 9.2 (0.855) 9.0 (0.836) 43-7/8" (1114) 13.6 (1.263)C24 5.5 (0.511) 4.3 (0.399) 18-5/16" (465) 14-7/16" (367) 43-1/8" (1095) 11.8 (1.096) 23' 1-5/8" (7052) 11.0 (1.022) 10.8 (1.003) 36-11/16" (932) 16.0 (1.486)C245 6.1 (0.567) 4.8 (0.446) 18-5/16" (465) 14-7/16" (367) 47-15/16" (1218) 13.1 (1.217) 24' 8-7/8" (7541) 12.2 (1.133) 12.0 (1.115) 31-7/8" (810) 17.6 (1.635)C25 7.0 (0.650) 5.5 (0.511) 18-5/16" (465) 14-7/16" (367) 55" (1397) 15.1 (1.403) 27' 1-1/8" (8258) 14.0 (1.301) 13.8 (1.282) 24-13/16" (630) 20.0 (1.858)C255 7.6 (0.706) 6.0 (0.557) 18-5/16" (465) 14-7/16" (367) 59-15/16" (1522) 16.4 (1.524) 28' 8-7/8" (8760) 15.3 (1.421) 15.0 (1.394) 19-7/8" (505) 21.6 (2.007)C26 8.5 (0.790) 6.7 (0.622) 18-5/16" (465) 14-7/16" (367) 67" (1702) 18.4 (1.709) 31' 1-1/8" (9477) 17.1 (1.589) 16.8 (1.561) 12-13/16" (325) 24.0 (2.230)C32 2.5 (0.232) 1.9 (0.177) 18-5/16" (465) 14-7/16" (367) 19-1/4" (489) 7.8 (0.726) 15' 2-1/8" (4626) 5.0 (0.464) 4.8 (0.446) 60-9/16" (1538) 12.0 (1.116)C325 3.0 (0.279) 2.4 (0.223) 18-5/16" (465) 14-7/16" (367) 23-7/16" (595) 9.6 (0.891) 16' 6-3/8" (5038) 6.0 (0.558) 5.8 (0.538) 56-3/8" (1432) 14.1 (1.311)C33 4.0 (0.372) 3.1 (0.288) 18-5/16" (465) 14-7/16" (367) 31-1/16" (789) 12.8 (1.189) 19' 1-3/8" (5826) 7.9 (0.734) 7.8 (0.725) 48-3/4" (1238) 17.9 (1.663)C335 4.6 (0.427) 3.6 (0.334) 18-5/16" (465) 14-7/16" (367) 35-15/16" (913) 14.8 (1.375) 20' 8-7/8" (6321) 9.2 (0.855) 9.0 (0.836) 43-7/8" (1114) 20.4 (1.895)C34 5.5 (0.511) 4.3 (0.399) 18-5/16" (465) 14-7/16" (367) 43-1/8" (1095) 17.7 (1.644) 23' 1-5/8" (7052) 11.0 (1.022) 10.8 (1.003) 36-11/16" (932) 24.0 (2.230)C345 6.1 (0.567) 4.8 (0.446) 18-5/16" (465) 14-7/16" (367) 47-15/16" (1218) 19.7 (1.830) 24' 8-7/8" (7541) 12.2 (1.134) 12.0 (1.115) 31-7/8" (810) 26.4 (2.453)C35 7.0 (0.650) 5.5 (0.511) 18-5/16" (465) 14-7/16" (367) 55" (1397) 22.6 (2.100) 27' 1-1/8" (8258) 14.0 (1.301) 13.8 (1.282) 24-13/16" (630) 29.9 (2.778)

Bold Italic = Straight-arm ‘C’ width units available as special orders.

NOTE: Floor to sill heights are calculated based upon a structural header height of 6' 10-1/2".

17

Casement Window Opening Specifications

Unit Number

Clear Opg. Straight ArmSq. Ft. (m2)

Clear Opg. Split Arm

Sq. Ft. (m2)


GlassSq. Ft. (m2)


Lineal Ft. (mm)

Straight Arm Vent

Sq. Ft. (m2)

Split Arm Vent

Sq. Ft. (m2)

Top of Subfloor to Top of Inside Sill

Stop Inches (m2)

Overall Unit AreaSq. Ft. (m2)

Straight Arm Width

Inches (mm)

Split Arm Width

Inches (mm)

Height

Inches (mm)

CW12 3.0 (0.279) 2.5 (0.232) 22-9/16" (573) 18-11/16" (475) 19-1/4" (489) 3.2 (0.297) 8' 3-9/16" (2529) 3.0 (0.279) 3.0 (0.279) 60-9/16" (1538) 4.8 (0.446)CW125 3.7 (0.344) 3.0 (0.279) 22-9/16" (573) 18-11/16" (475) 23-7/16" (595) 3.9 (0.362) 8' 11-11/16" (2726) 3.7 (0.344) 3.6 (0.334) 56-3/8" (1432) 5.6 (0.520)CW13 4.9 (0.455) 4.0 (0.372) 22-9/16" (573) 18-11/16" (475) 31-1/16" (789) 5.2 (0.483) 10' 3-3/16" (3129) 4.9 (0.455) 4.8 (0.446) 48-3/4" (1238) 7.1 (0.660)CW135* 5.7 (0.530) 5.1 (0.474) 22-9/16" (573) 20" (508) 36-3/8" (924) 6.0 (0.557) 11' 0-15/16" (3377) 5.7 (0.530) 5.5 (0.511) 43-7/8" (1114) 8.0 (0.743)CW14* 6.8 (0.632) 6.0 (0.557) 22-9/16" (573) 20" (508) 43-1/8" (1095) 7.2 (0.669) 12' 3-5/16" (3742) 6.8 (0.632) 6.6 (0.613) 36-11/16" (932) 9.5 (0.883)CW145* 7.5 (0.697) 6.7 (0.622) 22-9/16" (573) 20" (508) 47-15/16" (1218) 8.0 (0.743) 13' 0-15/16" (3986) 7.5 (0.697) 7.3 (0.678) 31-7/8" (810) 10.4 (0.966)CW15* 8.6 (0.799) 7.6 (0.706) 22-9/16" (573) 20" (508) 55" (1397) 9.2 (0.855) 14' 3-1/16" (4345) 8.6 (0.799) 8.4 (0.780) 24-13/16" (630) 11.8 (1.096)CW155* 9.4 (0.873) 8.3 (0.771) 22-9/16" (573) 20" (508) 59-15/16" (1522) 10.0 (0.929) 15' 0-15/16" (4596) 9.4 (0.873) 9.1 (0.845) 19-7/8" (505) 12.8 (1.189)CW16* 10.5 (0.975) 9.3 (0.864) 22-9/16" (573) 20" (508) 67" (1702) 11.2 (1.041) 16' 3-1/16" (4955) 10.5 (0.975) 10.2 (0.948) 12-13/16" (325) 14.2 (1.319)CW22 3.0 (0.279) 2.5 (0.232) 22-9/16" (573) 18-11/16" (475) 19-1/4" (489) 6.4 (0.594) 16' 7-1/8" (5058) 6.0 (0.558) 6.0 (0.558) 60-9/16" (1538) 9.6 (0.892)CW225 3.7 (0.344) 3.0 (0.279) 22-9/16" (573) 18-11/16" (475) 23-7/16" (595) 7.8 (0.724) 17' 11-3/8" (5452) 7.4 (0.688) 7.2 (0.668) 56-3/8" (1432) 11.2 (1.040)CW23 4.9 (0.455) 4.0 (0.372) 22-9/16" (573) 18-11/16" (475) 31-1/16" (789) 10.4 (0.966) 20' 6-3/8" (6258) 9.8 (0.910) 9.6 (0.892) 48-3/4" (1238) 14.1 (1.310)CW235* 5.7 (0.530) 5.1 (0.474) 22-9/16" (573) 20" (508) 36-3/8" (924) 12.0 (1.115) 22' 1-7/8" (6753) 11.4 (1.059) 11.1 (1.031) 43-7/8" (1114) 16.0 (1.486)CW24* 6.8 (0.632) 6.0 (0.557) 22-9/16" (573) 20" (508) 43-1/8" (1095) 14.4 (1.338) 24' 6-5/8" (7483) 13.5 (1.254) 13.1 (1.217) 36-11/16" (932) 18.8 (1.747)CW245* 7.5 (0.697) 6.7 (0.622) 22-9/16" (573) 20" (508) 47-15/16" (1218) 16.0 (1.486) 26' 1-7/8" (7972) 15.0 (1.394) 14.6 (1.356) 31-7/8" (810) 20.8 (1.932)CW25* 8.6 (0.799) 7.6 (0.706) 22-9/16" (573) 20" (508) 55" (1397) 18.3 (1.700) 28' 6-1/8" (8690) 17.3 (1.607) 16.7 (1.551) 24-13/16" (630) 23.5 (2.183)CW255* 9.4 (0.873) 8.3 (0.771) 22-9/16" (573) 20" (508) 59-15/16" (1522) 20.0 (1.858) 30' 1-7/8" (9192) 18.8 (1.747) 18.2 (1.691) 19-7/8" (505) 25.6 (2.378)CW26* 10.5 (0.976) 9.3 (0.864) 22-9/16" (573) 20" (508) 67" (1702) 22.3 (2.072) 32' 6-1/8" (9909) 21.0 (1.951) 20.4 (1.895) 12-13/16" (325) 28.2 (2.620)CX125 4.2 (0.388) 3.5 (0.330) 25-11/16" (653) 21-13/16" (554) 23 -7/16" (595) 4.4 (0.412) 9' 6" (2896) 4.2 (0.388) 4.1 (0.380) 56-3/8" (1432) 6.2 (0.577)CX13 5.5 (0.515) 4.7 (0.437) 25-11/16" (653) 21-13/16" (554) 31-1/16" (789) 5.9 (0.544) 10' 9-5/8" (3292) 5.5 (0.515) 5.4 (0.505) 48-3/4" (1238) 7.9 (0.730)CX135* 6.4 (0.596) 5.4 (0.505) 25-11/16" (653) 21-13/16" (554) 35-15/16" (913) 6.8 (0.629) 11' 7-1/4" (3536) 6.4 (0.596) 6.3 (0.585) 43-7/8" (1114) 8.9 (0.829)CX14* 7.7 (0.715) 6.5 (0.607) 25-11/16" (653) 21-13/16" (554) 43-1/8" (1095) 8.1 (0.755) 12' 9-5/8" (3901) 7.7 (0.715) 7.6 (0.703) 36-11/16" (932) 10.5 (0.975)CX145* 8.6 (0.795) 7.3 (0.674) 25-11/16" (653) 21-13/16" (554) 47-15/16" (1218) 9.0 (0.839) 13' 7-1/4" (4145) 8.6 (0.795) 8.4 (0.781) 31-7/8" (810) 11.6 (1.073)CX15* 9.8 (0.912) 8.3 (0.774) 25-11/16" (653) 21-13/16" (554) 55" (1397) 10.4 (0.963) 14' 9-5/8" (4511) 9.8 (0.912) 9.7 (0.897) 24-13/16" (630) 13.1 (1.217)CX155* 10.7 (0.993) 9.1 (0.843) 25-11/16" (653) 21-13/16" (554) 59-15/16" (1522) 11.3 (1.049) 15' 7-1/4" (4755) 10.7 (0.993) 10.5 (0.978) 19-7/8" (505) 14.2 (1.317)CX16* 12.0 (1.111) 10.1 (0.942) 25-11/16" (653) 21-13/16" (554) 67" (1702) 12.6 (1.172) 16' 9-5/8" (5121) 12.0 (1.111) 11.8 (1.094) 12-13/16" (325) 15.7 (1.461)CXW13 6.5 (0.604) 5.6 (0.526) 30-1/8" (765) 26-1/4" (667) 31-1/16" (789) 6.8 (0.632) 11' 6-5/16" (3513) 6.5 (0.604) 6.1 (0.567) 48-3/4" (1238) 9.0 (0.836)CXW135* 7.5 (0.697) 6.6 (0.613) 30-1/8" (765) 26-1/4" (667) 35-15/16" (913) 7.9 (0.734) 12' 4-1/16" (3761) 7.5 (0.697) 7.0 (0.650) 43-7/8" (1114) 10.2 (0.948)CXW14* 9.0 (0.836) 7.9 (0.734) 30-1/8" (765) 26-1/4" (667) 43-1/8" (1095) 9.5 (0.883) 13' 6 -7/16" (4126) 9.0 (0.836) 8.4 (0.780) 36-11/16" (932) 12.0 (1.115)CXW145* 10.0 (0.929) 8.8 (0.818) 30-1/8" (765) 26-1/4" (667) 47-15/16" (1218) 10.5 (0.975) 14' 4-1/16" (4371) 10.0 (0.929) 9.4 (0.873) 31-7/8" (810) 13.2 (1.226)

* These units meet or exceed the following dimensions: Clear Openable Area of 5.7 sq. ft., Clear Openable Width of 20" and Clear Openable Height of 24", when appropriate hardware (straight arm or split arm) is specified.

NOTE: Floor to sill heights are calculated based upon a structural header height of 6' 10-1/2".

Picture Window Glass/Unit Area

Unit NumberGlass

Sq. Ft. (m2)Overall Unit AreaSq. Ft. (m2)

P3030 6.8 (0.632) 9.0 (0.836)

P3035 7.8 (0.725) 10.2 (0.948)

P3040 9.4 (0.873) 12.0 (1.115)

P3045 10.4 (0.966) 13.2 (1.226)

P3050 12.0 (1.115) 14.9 (1.384)

P3055 13.0 (1.208) 16.2 (1.505)

P3060 14.6 (1.356) 17.9 (1.663)

P3530 7.8 (0.725) 10.2 (0.948)

P3535 9.0 (0.836) 11.6 (1.078)

P3540 10.8 (1.003) 13.6 (1.263)

P3545 12.1 (1.124) 15.0 (1.394)

P3550 13.8 (1.282) 17.0 (1.579)

P3555 15.1 (1.403) 18.4 (1.709)

P3560 16.8 (1.561) 20.4 (1.895)

P4030 9.4 (0.873) 12.0 (1.115)

Unit NumberGlass


P4035 10.8 (1.003) 13.6 (1.263)

P4040 13.0 (1.208) 16.0 (1.486)

P4045 14.5 (1.347) 17.6 (1.635)

P4050 16.6 (1.542) 20.0 (1.858)

P4055 18.1 (1.682) 21.6 (2.007)

P4060 20.2 (1.877) 24.0 (2.230)

P4530 10.4 (0.966) 13.2 (1.226)

P4535 12.1 (1.124) 15.0 (1.394)

P4540 14.5 (1.347) 17.6 (1.635)

P4545 16.1 (1.496) 19.4 (1.802)

P4550 18.4 (1.709) 22.0 (2.044)

P4555 20.1 (1.867) 23.8 (2.211)

P4560 22.4 (2.081) 26.4 (2.453)

P5030 12.0 (1.115) 14.9 (1.384)

P5035 13.8 (1.282) 17.0 (1.579)

Unit NumberGlass


P5040 16.6 (1.542) 20.0 (1.858)

P5045 18.4 (1.709) 22.0 (2.044)

P5050 21.1 (1.960) 24.9 (2.313)

P5055 23.0 (2.137) 26.9 (2.499)

P5060 25.7 (2.388) 29.9 (2.778)

P5530 13.0 (1.208) 16.2 (1.505)

P5535 15.1 (1.403) 18.4 (1.709)

P5540 18.1 (1.682) 21.6 (2.007)

P5545 20.1 (1.867) 23.8 (2.211)

P5550 23.0 (2.137) 26.9 (2.499)

P6030 14.6 (1.356) 17.9 (1.663)

P6035 16.8 (1.561) 20.4 (1.895)

P6040 20.2 (1.877) 24.0 (2.230)

P6045 22.4 (2.081) 26.4 (2.453)

P6050 25.7 (2.388) 29.9 (2.778)

400

C

asem

ent&

Awni

ngW

indo

ws

18


Transom Square Feet Glass/Unit Area

Unit NumberGlass


CTR1510 0.7 (0.065) 1.4 (0.130)

CTR1810 0.8 (0.074) 1.7 (0.158)

CTR21810 1.7 (0.159) 3.4 (0.315)

CTR31810 2.6 (0.238) 5.1 (0.472)

CTR2010 1.0 (0.093) 2.0 (0.186)

CTR22010 2.1 (0.194) 4.0 (0.372)

CTR32010 3.1 (0.291) 6.0 (0.556)

Unit NumberGlass


CTR2410 1.2 (0.111) 2.4 (0.223)

CTR22410 2.5 (0.236) 4.7 (0.437)

CTR2810 1.4 (0.130) 2.6 (0.242)

CTR/PTR3010 1.6 (0.149) 3.0 (0.279)

CTR5110 3.0 (0.279) 5.1 (0.472)

CTR2910 1.5 (0.139) 2.8 (0.260)

CTR3410 1.8 (0.167) 3.4 (0.316)

Unit NumberGlass


CTR/PTR4010 2.2 (0.204) 4.0 (0.372)

CTR4810 2.6 (0.242) 4.7 (0.437)

CTR/PTR6010 3.4 (0.316) 6.0 (0.557)

PTR3510 1.8 (0.167) 3.4 (0.316)

PTR4510 2.4 (0.223) 4.4 (0.409)

PTR5010 2.8 (0.260) 5.0 (0.465)

PTR5510 3.0 (0.279) 5.4 (0.502)

Awning Window Opening Specifications

Unit Number

Clear Opg.Sq. Ft. (m2)

Clear Opening in Full Open PositionGlassSq. Ft. (m2)


Lineal Ft. (mm)Vent

Sq. Ft. (m2)



Overall Unit Area

Sq. Ft. (m2)Width

Inches (mm)Depth

Inches (mm)AR21 0.8 (0.074) 19-1/2" (495) 5-15/16" (151) 1.7 (0.158) 6' 4-13/16" (1951) 0.8 (0.074) 67-7/16" (1713) 2.8 (0.260)AR221 0.9 (0.080) 19-1/2" (495) 6-3/8" (162) 3.4 (0.316) 12' 9-5/8" (3902) 1.7 (0.160) 67-7/16" (1713) 5.6 (0.520)AR2251 1.1 (0.098) 23-3/4" (603) 6-3/8" (162) 4.0 (0.372) 14' 0-5/8" (4283) 2.1 (0.195) 67-7/16" (1713) 6.6 (0.613)AR251 1.0 (0.093) 23-3/4" (603) 5-15/16" (151) 2.0 (0.186) 7' 0-5/16" (2157) 1.0 (0.093) 67-7/16" (1713) 3.3 (0.307)AR281 1.1 (0.103) 26-7/8" (683) 5-15/16" (151) 2.3 (0.217) 7' 0-5/8" (2326) 1.1 (0.103) 67-7/16" (1713) 3.7 (0.345)AR31 1.3 (0.121) 31-5/16" (795) 5-15/16" (151) 2.7 (0.251) 8' 4-7/16" (2551) 1.3 (0.121) 67-7/16" (1713) 4.2 (0.390)AR321 0.9 (0.080) 19-1/2" (495) 6-3/8" (162) 5.1 (0.474) 19' 2-7/16" (5853) 2.6 (0.241) 67-7/16" (1713) 8.4 (0.780)AR351 1.5 (0.139) 36-3/16" (919) 5-15/16" (151) 3.1 (0.288) 9' 2-3/16" (2799) 1.5 (0.139) 67-7/16" (1713) 4.8 (0.446)AR41 1.8 (0.167) 43-3/8" (1102) 5-15/16" (151) 3.8 (0.353) 10' 4-9/16" (3164) 1.8 (0.167) 67-7/16" (1713) 5.7 (0.530)AR451 2.0 (0.186) 48-3/16" (1224) 5-15/16" (151) 4.2 (0.390) 11' 2-3/16" (3408) 2.0 (0.186) 67-7/16" (1713) 6.2 (0.576)AR51 2.3 (0.214) 55-1/2" (1410) 5-15/16" (151) 4.8 (0.446) 12' 4-5/16" (3767) 2.3 (0.214) 67-7/16" (1713) 7.1 (0.660)AN21 0.8 (0.074) 19-1/2" (495) 6" (152) 2.2 (0.204) 6' 11-13/16" (2129) 0.8 (0.074) 63-15/16" (1624) 3.4 (0.316)AN221 0.9 (0.081) 19-1/2" (495) 6-7/16" (164) 4.4 (0.409) 13' 11-5/8" (4258) 1.7 (0.162) 63-15/16" (1624) 6.8 (0.632)AN2251 1.1 (0.099) 23-3/4" (603) 6-7/16" (164) 5.2 (0.483) 15' 3-7/8" (4670) 2.1 (0.197) 63-15/16" (1624) 8.0 (0.743)AN251 1.0 (0.093) 23-3/4" (603) 6" (152) 2.6 (0.242) 7' 7-15/16" (2335) 1.0 (0.093) 63-15/16" (1624) 4.0 (0.372)AN281 1.1 (0.104) 26-7/8" (683) 6" (152) 3.0 (0.277) 8' 0-3/16" (2503) 1.1 (0.104) 63-15/16" (1624) 4.5 (0.417)AN31 1.3 (0.121) 31-5/16" (795) 6" (152) 3.5 (0.325) 8' 11-7/16" (2730) 1.3 (0.121) 63-15/16" (1624) 5.1 (0.474)AN321 0.9 (0.081) 19-1/2" (495) 6-7/16" (164) 6.6 (0.613) 20' 11-7/16" (6387) 2.6 (0.243) 63-15/16" (1624) 10.2 (0.948)AN351 1.5 (0.139) 36-3/16" (919) 6" (152) 4.0 (0.372) 9' 9-3/16" (2977) 1.5 (0.139) 63-15/16" (1624) 5.8 (0.539)AN41 1.8 (0.167) 43-3/8" (1102) 6" (152) 4.8 (0.446) 10' 11-9/16" (3342) 1.8 (0.167) 63-15/16" (1624) 6.8 (0.632)AN451 2.0 (0.186) 48-3/16" (1224) 6" (152) 5.4 (0.502) 11' 9-3/16" (3586) 2.0 (0.186) 63-15/16" (1624) 7.5 (0.697)AN51 2.3 (0.214) 55-1/2" (1410) 6" (152) 6.2 (0.576) 12' 11-5/16" (3945) 2.3 (0.214) 63-15/16" (1624) 8.5 (0.790)A21 0.8 (0.074) 19-1/2" (495) 6-1/8" (156) 2.6 (0.242) 7' 7-1/16" (2313) 0.8 (0.074) 60-5/16" (1532) 4.0 (0.372)A212 0.9 (0.082) 19-1/2" (495) 6-1/2" (165) 5.2 (0.483) 15' 2-1/8" (4626) 0.9 (0.164) 60-5/16" (1532) 8.0 (0.743)A221 0.9 (0.082) 19-1/2" (495) 6-1/2" (165) 5.2 (0.483) 15' 2-1/8" (4626) 1.8 (0.164) 60-5/16" (1532) 8.0 (0.743)A2251 1.1 (0.100) 23-3/4" (603) 6-1/2" (165) 6.4 (0.595) 16' 6-3/8" (5039) 2.1 (0.199) 60-5/16" (1532) 9.6 (0.892)A251 1.0 (0.093) 23-3/4" (603) 6-1/8" (156) 3.2 (0.297) 8' 3-3/16" (2519) 1.0 (0.093) 60-5/16" (1532) 4.8 (0.446)A281 1.1 (0.106) 26-7/8" (683) 6-1/8" (156) 3.7 (0.340) 8' 0-13/16" (2687) 1.1 (0.106) 60-5/16" (1532) 5.3 (0.490)A31 1.3 (0.121) 31-5/16" (795) 6-1/8" (156) 4.3 (0.399) 9' 6-11/16" (2913) 1.3 (0.121) 60-5/16" (1532) 6.0 (0.557)A312 1.4 (0.131) 31-5/16" (795) 6-1/2" (165) 8.6 (0.799) 19' 1-3/8" (5826) 1.4 (0.263) 60-5/16" (1532) 12.0 (1.115)A321 0.9 (0.082) 19-1/2" (495) 6-1/2" (165) 7.8 (0.725) 22' 9-3/16" (6939) 2.6 (0.245) 60-5/16" (1532) 12.0 (1.115)A351 1.5 (0.139) 36-3/16" (919) 6-1/8" (156) 4.9 (0.455) 10' 4-7/16" (3161) 1.5 (0.139) 60-5/16" (1532) 6.8 (0.632)A41 1.8 (0.167) 43-3/8" (1102) 6-1/8" (156) 5.9 (0.548) 11' 6-13/16" (3526) 1.8 (0.167) 60-5/16" (1532) 8.0 (0.743)A451 2.1 (0.195) 48-3/16" (1224) 6-1/8" (156) 6.6 (0.613) 12' 4-7/16" (3770) 2.1 (0.195) 60-5/16" (1532) 8.8 (0.818)A51 2.5 (0.232) 55-1/2" (2323) 6-1/8" (156) 7.5 (0.697) 13' 6-9/16" (4129) 2.5 (0.232) 60-5/16" (1532) 10.0 (0.929)AW21 0.8 (0.074) 19-1/2" (495) 6-1/8" (156) 3.2 (0.297) 8' 3-9/16" (2529) 0.8 (0.074) 56-1/16" (1424) 4.8 (0.446)AW221 0.9 (0.082) 19-1/2" (495) 6-1/2" (165) 6.4 (0.595) 16' 7-1/8" (5058) 1.8 (0.164) 56-1/16" (1424) 9.6 (0.892)AW2251 1.1 (0.100) 23-3/4" (603) 6-1/2" (165) 7.8 (0.725) 17' 11-3/8" (5471) 2.1 (0.199) 56-1/16" (1424) 11.2 (1.040)AW251 1.0 (0.093) 23-3/4" (603) 6-1/8" (156) 3.9 (0.362) 8' 11-11/16" (2726) 1.0 (0.093) 56-1/16" (1424) 5.6 (0.520)AW281 1.1 (0.106) 26-7/8" (683) 6-1/8" (156) 4.4 (0.413) 9' 0-1/2" (2904) 1.1 (0.106) 56-1/16" (1424) 6.2 (0.577)AW31 1.3 (0.121) 31-5/16" (795) 6-1/8" (156) 5.2 (0.483) 10' 3-3/16" (3129) 1.3 (0.121) 56-1/16" (1424) 7.1 (0.660)AW321 0.9 (0.082) 19-1/2" (495) 6-1/2" (165) 9.6 (0.892) 24' 10-11/16" (7587) 2.6 (0.245) 56-1/16" (1424) 14.4 (1.338)AW351 1.5 (0.139) 36-3/16" (919) 6-1/8" (156) 6.0 (0.557) 11' 0-15/16" (3377) 1.5 (0.139) 56-1/16" (1424) 8.0 (0.743)AW41 1.8 (0.167) 43-3/8" (1102) 6-1/8" (156) 7.2 (0.669) 12' 3-5/16" (3742) 1.8 (0.167) 56-1/16" (1424) 9.5 (0.883)AW451 2.1 (0.195) 48-3/16" (1224) 6-1/8" (156) 8.0 (0.743) 13' 0-15/16" (3986) 2.1 (0.195) 56-1/16" (1424) 10.4 (0.966)AW51 2.4 (0.223) 55-1/2" (1410) 6-1/8" (156) 9.2 (0.855) 14' 3-1/16" (4345) 2.4 (0.223) 56-1/16" (1424) 11.8 (1.096)AX2251 1.1 (0.100) 23-3/4" (603) 6-1/2" (165) 8.9 (0.824) 18' 1" (5512) 2.1 (0.199) 53-15/16" (1370) 12.4 (1.153)AX251 1.0 (0.094) 23-3/4" (603) 6-1/8" (156) 4.4 (0.412) 9' 0-1/2" (2904) 1.0 (0.094) 53-15/16" (1370) 6.2 (0.577)AX281 1.1 (0.106) 26-7/8" (683) 6-1/8" (156) 5.0 (0.467) 10' 0-1/16" (3062) 1.1 (0.106) 53-15/16" (1370) 6.9 (0.640)AX31 1.3 (0.124) 31-5/16" (795) 6-1/8" (156) 5.9 (0.544) 10' 0-13/16" (3288) 1.3 (0.124) 53-15/16" (1370) 7.9 (0.730)AX351 1.5 (0.143) 36-3/16" (919) 6-1/8" (156) 6.8 (0.629) 11' 0-5/8" (3535) 1.5 (0.143) 53-15/16" (1370) 8.9 (0.829)AX41 1.8 (0.171) 43-3/8" (1102) 6-1/8" (156) 8.1 (0.755) 12' 0-13/16" (3901) 1.8 (0.171) 53-15/16" (1370) 10.5 (0.975)AX451 2.0 (0.190) 48-3/16" (1224) 6-1/8" (156) 9.0 (0.839) 13' 0-5/8" (4145) 2.0 (0.190) 53-15/16" (1370) 11.6 (1.073)AX51 2.4 (0.219) 55-1/2" (1410) 6-1/8" (156) 10.4 (0.963) 14' 0-3/4" (4504) 2.4 (0.219) 53-15/16" (1370) 13.1 (1.217)

19

Standard Divided Light Patterns for Casement Windows

Colonial Modi�ed Colonial*

Prairie AShort Fractional*

Tall Fractional*

* Also available with a 2-1/4" grille to simulate a check rail.

CR12 CN12 C12 CW12CR125 CN125 C125 CW125

CR13 CN13 C13 CW13CR135 CN135 C135 CW135

CR14 CN14 C14 CW14CR145 CN145 C145 CW145

CR15 CN15 C15 CW15CR155 CN155 C155 CW155

CR16 CN16 C16 CW16

CX13 CXW13CX135 CXW135

CX125

CX14 CXW14CX145 CXW145

CX15CX155

CX16

Unit Number Colonial Modi�ed Colonial*


Tall Fractional*

Unit Number

Standard Divided Light Patterns for Awning Windows

Colonial Prairie A

AR21 AR251AN21 AN251A21 A251AW21 AW251

AR281 AR31 AR351AN281 AN31 AN351A281 A31 A231AW281 AW31 AW351

AR41 AR451AN41 AN451A41 A451AW41 AW451

AR51 AW51AN51 A551A51

Unit Number

Custom Pattern ExamplesSpeci�ed Equal Light Examples

Speci�ed equal light and custom patterns are also available.For more information on Andersen™ divided light, see page 2-3 or visit andersenwindows.com/grilles.

Standard Divided Light Patterns for Casement and Awning Picture Windows


Tall Fractional*


Victorian

P3030 P3530P3035 P3535

P3040 P3540P3045 P3545

P3050 P3550P3055 P3555

P3060 P3560

P4030 P4530P4035 P4535

P4040 P4540P4045 P4545

Unit Number

400

C

asem

ent&

Awni

ngW

indo

ws

20

Casement & Awning WindowsStandard Divided Light Patterns for Casement and Awning Picture Windows — Continued

Speci�ed equal light and custom patterns are also available. For more information on Andersen™ divided light, see page 2-3 or visit andersenwindows.com/grilles.


Tall Fractional*


Victorian


P5030 P5530P5035 P5535

P5040 P5540P5045 P5545

P5050 P5550P5055

P5060

P6030P6035

P6040P6045

P6050

Unit Number

Custom Pattern ExamplesSpeci�ed Equal Light Examples

P4050 P4550P4055 P4555

P4060 P4560

With traditional styling and state-of-the-art technology, Andersen® 400 Series tilt-wash double-hung

windows give you the beauty of natural wood interiors, weathertight performance and a long-lasting,*

low-maintenance exterior. The unique tilt-wash system makes cleaning these windows a breeze.

Section Reference

Table of Basic Sizes ............ 24

Standard Divided Light Patterns ...................... 27

Basic Unit Details ................. 29

Opening Specifications ......... 31

Combination Design ............ 70

Performance Data ............... 75

Tilt-Wash Double-Hung Windows

400

T

ılt-W

ash

Doub

le-Hu

ngW

indow

s

* See limited warranty for details.

golddust blackwhite stonesatinnickel

oilrubbedbronze

22

Features


Tilt-Wash Lock & Keeper


Hardware Finishes



• High-Performance™

Low-E4® tempered impact-resistant glass


• High-Performance™ Low-E4® SmartSun™ tempered impact-resistant glass



‡ Infringes on the overall net clear opening. Unit clear openable area may not meet egress requirements. See your local code official for more information.

“Flexacron” is a registered trademark of PPG Industries, Inc.

* For complete information on our warranties, visit andersenwindows.com or contact your Andersen supplier.


FRame

Exterior outer frame members are covered with a pre-formed rigid vinyl PVC cladding glued to a wood core, preventing corrosion, minimizing maintenance and providing an attractive appearance. Andersen® tilt-wash windows are available in four neutral colors. Specify White, Sandtone, Terratone® or Forest Green color.

For exceptionally long-lasting* performance, sill members are constructed with a solid wood core and corrosion-resistant Fibrex® composite material exterior. Sill ends are protected and sealed with weather- resistant covers.

Natural wood stops are made of treated, clear pine that can be finished to match the interior décor. On white prefinished interior units the stops are white foamed PVC.

For additional protection from air and water infil-

tration, the sill stop is 1-1/2'' high.‡ (Standard sill stop height

is 13/16''.) Interior wood stops are secured to the frame using 1-1/2'' 16 gauge crown staples instead of nails.

A factory-applied rigid vinyl anchoring flange on the head, sill and side of the outer frame helps seal the unit to the structure.

An extruded rigid patented vinyl jamb liner and fin provide a protective seal against the outer frame members. Exclusive slide wash assists make it easy to tilt sash into wash mode position.

Exterior frame and sill brackets provide

structural support for the sash during storm pressures. Brackets are colored to match exterior color of unit.

Weatherstripping throughout the unit provides a long-lasting,* energy-efficient, weather-repellent seal. For the top and bottom rails, an encased foam material is used. The head jamb liner and sill have a rigid vinyl rib that the weatherstripping material compresses against. At the check rail, compressible vinyl bulb material is used. Side jamb liners use leaf type weatherstripping.

Unique block and tackle counter balances feature sized-to-the-unit, rust-resistant springs that require no adjustment. Glass-reinforced nylon balancer shoes provide smooth, reliable sash operation. To prevent accidental release when in wash mode, they automatically lock into position with a patented stainless steel retainer clip.

SaSH

A polyester stabilized coat with a Flexacron® finish is electrostatically applied to penetrate all exterior surfaces for maximum protection and a lustrous finish.

Wood sash members are treated with a water-repellent wood preservative for long- lasting* protection and performance. Interior surfaces are unfinished clear pine. Low-maintenance prefinished interiors are also available.

glaSS

A rigid vinyl glazing bead with flexible lip, combined with structural silicone glazing, provides superior weathertightness and durability.

Consult local building codes for glass most suitable to your area. Glass options include:

• Standard High-Performance™ Low-E4® glass (PG Upgrade)

• Standard High Performance™ Low E-4® Sun glass (PG Upgrade)

• Standard High Performance™ Low E-4® SmartSun™ glass (PG Upgrade)

• High-Performance™ Low-E4®


• High-Performance™ Low-E4® Sun impact-resistant glass

• High-Performance™ Low-E4® SmartSun™

Printing limitations prevent

exact color duplication. See

your Andersen supplier for

actual color samples.

Available in satin nickel, oil rubbed bronze, white, stone, gold dust and black finish.

exterior Interior

pinewhite


Specify a unit exterior color option and an interior finish option to complete your order.

A metal lock and keeper creates a strong, secure engagement. Two locks are applied for added protection.

Current Estate™ hardware is available for PG Upgrade units. Please contact your Andersen supplier for more details.


23


cause damage to rigid vinyl. • Products in Sandtone or Terratone® color

may be painted any color lighter than Terratone using quality oil-base or latex paint. Submit color samples to Andersen for approval when painting White. Submit color samples to Andersen for approval when painting Sandtone or Terratone any color darker than Terratone.

• Do not paint Forest Green exteriors.• Creosote-based stains should not come

in contact with Andersen products. • Do not paint weatherstripping. • Abrasive cleaners or solutions




‡ Infringes on the overall net clear opening. Unit clear openable area may not meet egress requirements. See your local code official for more information.

“Frank Lloyd Wright” is a registered trademark of the Frank Lloyd Wright Foundation.


RetRactable InteRIoR bRacket

Interior brackets provide additional structural support for the sash and frame. The brackets retract out of sight when not in use. Available with a stone finish or a white finish with white interior units. Brackets must be engaged to meet structural requirements.

Retracted

Engaged

eXteRIoR bRacketS

Exterior Brackets

FRame

Extension JambsStandard jamb width is 4-1/2'' (114). Jamb depth can be 4-1/8'' (105) if nailing flange is reversed.

Non-Applied Extension JambsPine extension jambs are available for the following wall thicknesses:

• 5-1/4'' (133) • 6-9/16'' (167) • 7-1/8'' (181)

The side and head extension jambs are pre-drilled in the following width:

• 6-9/16'' (167)

Some sizes may be pine veneer.

Factory-Applied Extension JambsAvailable in 6-9/16" depth in pine or prefinished white (choose either painted or vinyl-wrapped white options). Please contact your Andersen supplier for details.

Pine StoolA clear pine stool is available and ready for finishing. The tilt-wash stool is available in 4-9/16'' (116) for use in wall depths up to 5-1/4'' (133) and 6-9/16'' (167) for use in wall depths up to 7-1/8'' (181). Works with 2-1/4'' and 2-1/2'' wide casings.

InStallatIon SyStem



glaSS

Andersen® Art GlassAndersen art glass panels come in eleven original patterns, including four Frank Lloyd Wright ® series designs. See the Andersen ® Product Guide for details on Andersen art glass, or visit andersenwindows.com/artglass for pattern information.

As with units with impact- resistant glass, a high inside sill stop is included with PG Upgrade tilt-wash units. Specify pine or prefinished white. Use of high inside sill stop will subtract 5/8'' (16) from clear opening height.

InSect ScReenS

TruScene® Insect Screen

TruScene insect screens provide over 50% more clarity than our conventional insect screens.

Conventional Insect ScreenConventional Perma-Clean® insect screens are available with finished frames in White, Sandtone, Terratone® and Forest Green colors to match product exteriors.

alSo avaIlable

Woodwright® Double-Hung WindowsPG Upgrades‡ are also available for select Woodwright sizes. Ask your Andersen supplier for details.


eXcluSIve

Pg uPgRaDeS‡

400

T

ılt-W

ash

Doub

le-Hu

ngW

indow

s


24

2'-1 5/8"

2'-2 1/8"

2'-5 5/8"

2'-6 1/8"

2'-9 5/8"

2'-10 1/8"

3'-1 5/8"

3'-2 1/8"

3'-5 5/8"

3'-6 1/8"

13 1

5 /16

"

3'-4

7/ 8

"

15 1

5 /16

"

4'-0

7/ 8

"

19 1

5 /16

"

4'-4

7/ 8

"

21 1

5 /16

"

4'-8

7/ 8

"

23 1

5 /16

"

5'-4

7/ 8

"

27 1

5 /16

"

5'-8

7/ 8

"

29 1

5 /16

"

6'-4

7/ 8

"

33 1

5 /16

" Unit Dimension


Unobstructed Glass*

1'-9 5/8"

1'-101/8"

3'-0

7/ 8

"

3'-9 5/8"

3'-10 1/8"

15" 19" 23" 27" 31" 35" 39"

2'-7 5/8"

2'-8 1/8" 3'-0 1/8"

2'-11 5/8"

25" 29"

3'-8

7/ 8

"

17 1

5 /16

"

5'-0

7/ 8

"

25 1

5 /16

"

6'-0

7/ 8

"

3'-4

7/ 8

" 4'

-0 7

/ 8"

4'-4

7/ 8

" 4'

-8 7

/ 8"

5'-4

7/ 8

" 5'

-8 7

/ 8"

6'-4

7/ 8

" 3'

-0 7

/ 8"

3'-8

7/ 8

" 5'

-0 7

/ 8"

6'-0

7/ 8

"

31 1

5 /16

"

Table of Basic Unit Sizes Scale 1/8" = 1'-0" (1:96)

* Unobstructed glass height is for single sash only.

These units meet or exceed the following dimensions: Clear Openable Area of 5.7 sq. ft., Clear Openable Width of 20" and Clear Openable Height of 24".


• “Unit Dimension” always refers to outside frame to frame dimension.

• Dimensions in parentheses are in millimeters.

• When ordering, be sure to specify color desired: White, Sandtone, Terratone®

or Forest Green.


NOTE: These sizes with PG Upgrade are rated at +50/-55

(991)

(562)

(549)

(381)

(937

)

(354

)

(664)

(651)

(483)

(765)

(752)

(584)

(867)

(854)

(686)

(968)

(956)

(787)

(1070)

(1057)

(889)

(195

3)

(862

)

(174

9)(1

648)

(710

)

(144

5)

(608

)

(134

3)

(557

)

(124

1)

(506

)

(103

8)

(405

)(7

60)

(1172)

(1159)

(816)

(803)

(917)

(905)

(737)(635)

(114

0)

(456

)

(154

6)

(659

)

(185

1)

(937

)(1

953)

(174

9)(1

648)

(144

5)(1

343)

(124

1)(1

038)

(114

0)(1

546)

(185

1)

(811

)

TW3062TW2862TW2062

TW3456TW3056TW2856

TW3452TW3052

TW3446

TW2852TW2452TW2052

TW2046TW1846 TW3046TW2846TW2446

TW3442TW3042TW2842TW2442TW2042TW1842

TW34310TW30310TW28310TW24310

TW3432TW3032TW2832TW2432TW2032

TW30210TW28210TW24210

TW20310

TW20210TW18210 TW34210

TW2456

TW2462 TW3462

TW1832

TW18310

TW1852

TW2056TW1856

TW1862

TW3852

TW3846

TW3856

TW3862

TW3842

TW38310

TW3832

TW38210

TW2636

TW21062

TW21056

TW21052

TW21046

TW21042

TW210310

TW210210

TW21032

TW21036

TW210410TW26410

TW210510TW26510

TW2656

TW2662

TW2652

TW2646

TW2642

TW26310

TW26210

TW2632

TW3436TW3036TW2836TW2436TW2036TW1836 TW3836

TW34410TW20410TW18410 TW30410TW28410TW24410 TW38410

TW34510TW20510TW18510 TW30510TW28510TW24510 TW38510

Cottage Style UnitsAvailable for these heights below,

starting at 310 height up to 52 height, in all widths. Contact dealer for lead times.

25

Unit Dimension

Unobstructed Glass

3'-1 5/8"

3'-2 1/8"

32 11/16" 36 11/16" 42 3/8" 46 3/8" 54 3/8" 62 3/8"

3'-5 5/8"

3'-6 1/8"

4'-0

7/ 8

" 4'

-4 7

/ 8"

4'-8

7/ 8

" 5'

-4 7

/ 8"

5'-8

7/ 8

" 6'

-0 7

/ 8"

3'-11 7/8"

1'-0"

1'-0 1/2"

7 1/16"

3'-11 5/16"

4'-3 7/8"

4'-3 5/16"

4'-11 7/8"

4'-11 5/16"

5'-7 7/8"

5'-7 5/16"

41 5

/ 16"

45

5/ 1

6"

49 5

/ 16"

57

5/ 1

6"

5'-0

7/ 8

"

53 5

/ 16"

61

5/ 1

6"

65 5

/ 16"

6'-4

7/ 8

"

4'-0

7/ 8

" 4'

-4 7

/ 8"

4'-8

7/ 8

" 5'

-4 7

/ 8"

5'-8

7/ 8

" 6'

-0 7

/ 8"

5'-0

7/ 8

" 6'

-4 7

/ 8"

69 5

/ 16"

(968)

(956)

(830)

(1070)

(1057)

(932)

(318)

(305)

(179)

(1216)

(1202)

(1076)

(1318)

(1303)

(1178)

(1521)

(1507)

(1381)

(1724)

(1710)

(1584)

(185

1)

(165

9)

(195

3)

(176

1)

(174

9)(1

648)

(144

5)(1

343)

(124

1)

(155

7)(1

456)

(154

7)

(185

1)(1

953)

(174

9)(1

648)

(144

5)(1

343)

(124

1)(1

547)

(135

5)(1

253)

(115

1)(1

049)

DHP30310‡ DHP310310‡

DHP3052‡DHP1052

DHP310510‡ DHP42510‡

DHP31062‡ DHP4262‡

DHP31056‡

DHP31052‡

DHP4256‡

DHP4252‡

DHP3042‡

DHP3046‡DHP1046

DHP1042

DHP31046‡

DHP31042‡DHP3442‡

DHP3446‡ DHP4246‡

DHP4242‡

DHP42310‡

DHP41052‡

DHP310410‡ DHP42410‡

DHP41046‡

DHP41042‡

DHP410310‡

DHP5642‡

DHP5646‡

DHP10310 DHP34310‡

DHP3056‡

DHP30510‡DHP10510

DHP1056

DHP34510‡

DHP3456‡

DHP3452‡

DHP410510‡ DHP56510‡

DHP3062‡DHP1062 DHP3462‡ DHP41062‡ DHP5662

DHP41056‡ DHP5656‡

DHP5652‡

DHP34410‡ DHP56410‡

DHP56310‡

DHP30410‡DHP10410 DHP410410‡

Table of Picture Unit Sizes Scale 1/8" = 1'-0" (1:96)

• Picture windows are not available with monolithic impact-resistant glass.




• When ordering, be sure to specify color desired: White, Sandtone, Terratone® or Forest Green.

‡ Andersen® art glass panels are available for these sizes by special order only. Interior art glass trim not available. Contact your Andersen supplier.


Square Feet Glass/Unit Area

Unit NumberGlass


DHP10310 2.03 (0.189) 4.07 (0.378)

DHP1042 2.22 (0.206) 4.41 (0.410)

DHP1046 2.42 (0.225) 4.74 (0.440)

DHP10410 2.61 (0.243) 5.07 (0.471)

DHP1052 2.81 (0.261) 5.41 (0.503)

DHP1056 3.01 (0.280) 5.74 (0.533)

DHP10510 3.20 (0.297) 6.07 (0.564)

DHP1062 3.40 (0.316) 6.41 (0.596)

DHP30310 9.38 (0.871) 12.77 (1.186)

DHP3042 10.29 (0.956) 13.82 (1.284)

DHP3046 11.19 (1.040) 14.86 (1.381)

DHP30410 12.10 (1.124) 15.91 (1.478)

DHP3052 13.01 (1.209) 16.95 (1.575)

DHP3056 13.92 (1.293) 18.00 (1.672)

DHP30510 14.83 (1.378) 19.04 (1.769)

DHP3062 15.73 (1.461) 20.09 (1.866)

DHP34310 10.53 (0.978) 14.13 (1.313)

DHP3442 11.54 (1.072) 15.28 (1.420)

DHP3446 12.56 (1.167) 16.44 (1.527)

DHP34410 13.58 (1.262) 17.60 (1.635)

DHP3452 14.60 (1.356) 18.75 (1.742)

DHP3456 15.62 (1.451) 19.91 (1.850)

DHP34510 16.64 (1.546) 21.07 (1.957)

DHP3462 17.66 (1.641) 22.22 (2.064)

DHP310310 12.16 (1.130) 16.06 (1.492)

DHP31042 13.33 (1.238) 17.37 (1.614)

DHP31046 14.51 (1.348) 18.69 (1.736)

DHP310410 15.69 (1.458) 20.00 (1.858)

DHP31052 16.87 (1.567) 21.32 (1.981)

DHP31056 18.04 (1.676) 22.63 (2.102)

DHP310510 19.22 (1.786) 23.94 (2.224)

DHP31062 20.40 (1.895) 25.26 (2.347)

DHP42310 13.30 (1.236) 17.42 (1.618)

DHP4246 15.88 (1.475) 20.27 (1.883)

DHP42410 17.17 (1.595) 21.69 (2.015)

DHP4252 18.46 (1.715) 23.12 (2.148)

DHP4256 19.75 (1.835) 24.54 (2.280)

DHP42510 21.03 (1.954) 25.97 (2.413)

DHP4262 22.32 (2.074) 27.39 (2.545)

DHP410310 15.60 (1.449) 20.13 (1.870)

DHP41042 17.11 (1.590) 21.78 (2.023)

DHP41046 18.62 (1.730) 23.43 (2.177)

DHP410410 20.13 (1.870) 25.07 (2.329)

DHP41052 21.64 (2.010) 26.72 (2.482)

DHP41056 23.15 (2.151) 28.37 (2.636)

DHP410510 24.66 (2.291) 30.02 (2.789)

DHP41062 26.17 (2.431) 31.66 (2.941)

DHP56310 17.89 (1.662) 22.85 (2.123)

DHP5642 19.63 (1.824) 24.72 (2.297)

DHP5646 21.36 (1.984) 26.59 (2.470)

DHP56410 23.09 (2.145) 28.46 (2.644)

DHP5652 24.83 (2.307) 30.33 (2.818)

DHP5656 26.56 (2.468) 32.20 (2.991)

DHP56510 28.29 (2.628) 34.07 (3.165)

DHP5662 30.02 (2.789) 35.93 (3.338)

400

T

ılt-W

ash

Doub

le-Hu

ngW

indow

s


26

12 11

/ 16"

5 3 /

8"

1'-7

5 /16

"

1'-7

7 /8"

1'-0

"

1'-0

1 /2"

14 11

/ 16"

1'-9

5 /16

"

1'-9

7 /8"

18 11

/ 16"

2'-1

5 /16

"

2'-1

7 /8"

20 11

/ 16"

2'-3

5/ 1

6"

2'-3

7 /8"

22 11

/ 16"

2'-5

5 /16

"

2'-5

7 /8"

26 11

/ 16"

2'-9

5/ 1

6"

2'-9

7 /8"

32 1

1 /16

"

3'-3

5/ 1

6"

3'-3

7/ 8

"2'-1 5/8"

2'-2 1/8"

2'-5 5/8"

2'-6 1/8"

2'-9 5/8"

2'-10 1/8"

3'-1 5/8"

3'-2 1/8"

3'-5 5/8"

3'-6 1/8"

Unit Dimension


Unobstructed Glass

1'-9 5/8"

1'-10 1/8"

3'-9 5/8"

3'-10 1/8"

15" 19" 23" 27" 31" 35" 39"

2'-7 5/8"

2'-8 1/8" 3'-0 1/8"

2'-11 5/8"

25" 29"

(816)

(803)

(917)

(905)

(737)(635)

(101

2)

(999

)

(829

)

(860

)

(846

)

(677

)

(758

)

(745

)

(575

)

(707

)

(694

)

(525

)

(657

)

(643

)

(474

)

(555

)

(541

)

(372

)

(504

)

(491

)

(321

)

(318

)

(305

)

(136

)(562)

(549)

(380)

(664)

(651)

(482)

(765)

(752)

(583)

(867)

(854)

(685)

(968)

(955)

(787)

(1070)

(1057)

(888)

(1172)

(1159)

(990)

TWT1810 TWT2010 TWT2410 TWT2810 TWT3010








TWT3410

TWT3415

TWT3417

TWT34111

TWT3421

TWT3423

TWT3427

TWT3431

TWT3810

TWT3815

TWT3817

TWT38111

TWT3821

TWT3823

TWT3827

TWT3831

TWT2610 TWT21010

TWT2615 TWT21015

TWT2617 TWT21017

TWT26111 TWT210111

TWT2621 TWT21021

TWT2623 TWT21023

TWT2627 TWT21027

TWT2631 TWT21031

Table of Transom Unit Sizes Scale 1/8" = 1'-0" (1:96)



• Dimensions in parentheses are in millimeters.• When ordering, be sure to specify color

desired: White, Sandtone, Terratone® or Forest Green.

• Andersen® art glass panels are available for all sizes on this page.

4'-3 5/16"

45 1/4"

4'-3 7/8"

3'-11 5/16"

41 1/4"

4'-11 5/16"

53 1/4"

4'-11 7/8"

5'-7 5/16"

61 1/4"

5'-7 7/8"

6'-3 5/16"

69 1/4"

6'-3 7/8"3'-11 7/8"

Unit Dimension


Unobstructed Glass

6 3 /

16"

1'-0

"

1'-0

1 /2"

(318

)

(305

)

(157

)

(1215)

(1202)

(1048)

(1520)

(1506)

(1353)

(1317)

(1303)

(1149)

(1710)

(1556)

(1927)

(1913)

(1745)

(1724)


Square Feet Glass/Unit Area

Unit Number

GlassSq. Ft. (m2)

Overall Unit Area

Sq. Ft. (m2)

TWT1810 0.56 (0.052) 1.80 (0.167)

TWT1815 1.32 (0.123) 2.90 (0.269)

TWT1817 1.52 (0.141) 3.20 (0.297)

TWT18111 1.94 (0.180) 3.80 (0.353)

TWT1821 2.15 (0.200) 4.10 (0.381)

TWT1823 2.35 (0.218) 4.40 (0.409)

TWT1827 2.77 (0.257) 5.00 (0.465)

TWT1831 3.39 (0.315) 5.90 (0.548)

TWT2010 0.70 (0.065) 2.14 (0.199)

TWT2015 1.67 (0.155) 3.44 (0.320)

TWT2017 1.93 (0.179) 3.79 (0.352)

TWT20111 2.46 (0.229) 4.50 (0.418)

TWT2021 2.72 (0.253) 4.86 (0.452)

TWT2023 2.98 (0.277) 5.22 (0.485)

TWT2027 3.51 (0.326) 5.93 (0.551)

TWT2031 4.30 (0.399) 7.00 (0.650)

TWT2410 0.85 (0.079) 2.47 (0.229)

TWT2415 2.02 (0.188) 3.97 (0.369)

TWT2417 2.34 (0.217) 4.38 (0.407)

TWT24111 2.98 (0.277) 5.21 (0.484)

Unit Number

GlassSq. Ft. (m2)

Overall Unit Area

Sq. Ft. (m2)

TWT2421 3.29 (0.306) 5.62 (0.522)

TWT2423 3.61 (0.335) 6.03 (0.560)

TWT2427 4.25 (0.395) 6.85 (0.636)

TWT2431 5.21 (0.484) 8.09 (0.752)

TWT2610 0.93 (0.086) 2.64 (0.245)

TWT2615 2.19 (0.203) 4.24 (0.394)

TWT2617 2.54 (0.236) 4.68 (0.435)

TWT26111 3.23 (0.300) 5.56 (0.517)

TWT2621 3.58 (0.333) 6.00 (0.557)

TWT2623 3.93 (0.365) 6.44 (0.598)

TWT2627 4.62 (0.429) 7.32 (0.680)

TWT2631 5.66 (0.526) 8.63 (0.802)

TWT2810 1.00 (0.093) 2.80 (0.260)

TWT2815 2.37 (0.220) 4.51 (0.419)

TWT2817 2.74 (0.255) 4.98 (0.463)

TWT28111 3.49 (0.324) 5.91 (0.549)

TWT2821 3.87 (0.360) 6.38 (0.593)

TWT2823 4.24 (0.394) 6.84 (0.635)

TWT2827 4.99 (0.464) 7.78 (0.723)

TWT2831 6.12 (0.569) 9.18 (0.853)

Unit Number

GlassSq. Ft. (m2)

Overall Unit Area

Sq. Ft. (m2)

TWT21010 1.07 (0.099) 2.97 (0.0276)

TWT21015 2.55 (0.237) 4.78 (0.444)

TWT21017 2.95 (0.274) 5.27 (0.490)

TWT210111 3.75 (0.348) 6.26 (0.582)

TWT21021 4.15 (0.386) 6.76 (0.628)

TWT21023 4.56 (0.424) 7.25 (0.674)

TWT21027 5.36 (0.498) 8.24 (0.766)

TWT21031 6.57 (0.610) 9.73 (0.904)

TWT3010 1.15 (0.107) 3.14 (0.292)

TWT3015 2.72 (0.253) 5.05 (0.469)

TWT3017 3.15 (0.293) 5.57 (0.517)

TWT30111 4.01 (0.373) 6.61 (0.614)

TWT3021 4.44 (0.412) 7.14 (0.663)

TWT3023 4.87 (0.452) 7.66 (0.712)

TWT3027 5.73 (0.532) 8.70 (0.808)

TWT3031 7.02 (0.652) 10.27 (0.954)

TWT3410 1.30 (0.121) 3.47 (0.322)

TWT3415 3.07 (0.285) 5.58 (0.518)

TWT3417 3.56 (0.331) 6.16 (0.572)

TWT34111 4.53 (0.421) 7.32 (0.680)

Unit Number

GlassSq. Ft. (m2)

Overall Unit Area

Sq. Ft. (m2)

TWT3421 5.02 (0.466) 7.89 (0.733)

TWT3423 5.50 (0.511) 8.47 (0.787)

TWT3427 6.47 (0.601) 9.63 (0.895)

TWT3431 7.93 (0.737) 11.36 (1.055)

TWT3810 1.45 (0.135) 3.80 (0.353)

TWT3815 3.42 (0.318) 6.12 (0.569)

TWT3817 3.97 (0.369) 6.75 (0.627)

TWT38111 5.05 (0.469) 8.02 (0.745)

TWT3821 5.59 (0.519) 8.65 (0.804)

TWT3823 6.13 (0.569) 9.29 (0.863)

TWT3827 7.21 (0.670) 10.55 (0.980)

TWT3831 8.84 (0.821) 12.46 (1.158)

TWT31010 1.51 (0.140) 3.94 (0.366)

TWT4210 1.66 (0.154) 4.28 (0.398)

TWT41010 1.95 (0.181) 4.94 (0.459)

TWT5610 2.25 (0.209) 5.61 (0.521)

TWT6210 2.55 (0.237) 6.28 (0.583)

27

ColonialUnit Number

ColonialUnit Number

TW3056 TW3456 TW3856

TW30210 TW3421O TW38210TW3032 TW3432 TW3832TW3036 TW3436 TW3836TW30310 TW34310 TW38310TW3042 TW3442 TW3842TW3046 TW3446 TW3846TW30410 TW34410 TW38410TW3052 TW3452 TW3852

TW30510 TW34510 TW38510TW3062 TW3462 TW3862

ColonialUnit Number Prairie A*

TW18210TW1832TW1836TW18310TW1842TW1846TW18410TW1852

TW1856

TW18510TW1862

TW20210 TW24210 TW26210 TW28210 TW210210TW2032 TW2432 TW2632 TW2832 TW21032TW2036 TW2436 TW2636 TW2836 TW21036TW20310 TW24310 TW26310 TW28310 TW210310TW2042 TW2442 TW2642 TW2842 TW21042TW2046 TW2446 TW2646 TW2846 TW21046TW20410 TW24410 TW26410 TW28410 TW210410TW2052 TW2452 TW2652 TW2852 TW21052

TW2056 TW2456 TW2656 TW2856 TW21056

TW20510 TW24510 TW26510 TW28510 TW210510TW2062 TW2462 TW2662 TW2862 TW21062

ColonialUnit Number

ColonialUnit NumberColonialUnit Number

Speci�ed Equal Light and Custom Pattern examples*

Specied Equal Light

Standard Divided Light Patterns for Tilt-Wash Double-Hung Windows

Both grille patterns are available for all units in upper sash only (USO).

Custom patterns are also available. For more information on Andersen® divided light, see pages 2-3.

NOTE: Some sizes have restrictions on the number of lights wide that are available for specied equal light grille patterns. Please consult your Andersen® supplier for details.

Double-Hung Divided LightOrdering Prex

400 Series Tilt-Wash

Double-Hung TWPicture DHPTransom TWT

Standard Divided Light Patterns for Tilt-Wash Double-Hung Transom Windows

Colonial

TWT1815TWT1817TWT18111TWT1821TWT1823TWT1827

TWT2015 TWT2415 TWT2615 TWT2815 TWT21015TWT2017 TWT2417 TWT2617 TWT2817 TWT21017TWT20111 TWT24111 TWT26111 TWT28111 TWT210111TWT2021 TWT2421 TWT2621 TWT2821 TWT21021TWT2023 TWT2423 TWT2623 TWT2823 TWT21023TWT2027 TWT2427 TWT2627 TWT2827 TWT21027

TWT2031 TWT2431 TWT2631 TWT2831 TWT21031TWT1831

TWT3015 TWT3415 TWT3815TWT3017 TWT3417 TWT3817TWT30111 TWT34111 TWT38111TWT3021 TWT3421 TWT3821TWT3023 TWT3423 TWT3823TWT3027 TWT3427 TWT3827

TWT3031 TWT3431 TWT3831

TWT1810 TWT2010 TWT2410 TWT2810TWT2610 TWT21010 TWT3010 TWT410

TWT3810 TWT31010 TWT4210 TWT41010 TWT5610 TWT6210

400

T

ılt-W

ash

Doub

le-Hu

ngW

indow

s


28

DHP42510 DHP410510 DHP56510DHP4262 DHP41062 DHP5662

DHP4256 DHP41056 DHP5656

DHP42310 DHP410310 DHP56310DHP4242 DHP41042 DHP5642DHP4246 DHP41046 DHP5646DHP42410 DHP410410 DHP56410DHP4252 DHP41052 DHP5652

Modi�edColonial

ShortFractional

VictorianColonial

Modi�edColonial

Modi�edColonial

w/Check Rail*

Modi�edColonial

w/Check Rail*

ShortFractional

VictorianColonial

DHP310310DHP31042DHP31046DHP310410DHP31052

DHP310510DHP31062

DHP31056

Modi�edColonial

Modi�edColonial

w/Check Rail*

ShortFractional

VictorianColonialUnit Number

Unit Number

Unit Number

Unit Number Colonial

DHP3056 DHP3456

DHP30510 DHP34510DHP3062 DHP3462

DHP30310 DHP34310DHP3042 DHP3442DHP3046 DHP3446DHP30410 DHP34410DHP3052 DHP3452

Standard Divided Light Patterns for Tilt-Wash Double-Hung Picture Windows

DHP10310DHP1042DHP1046DHP10410DHP1052

DHP10510DHP1062

DHP1056

Double-Hung Divided LightOrdering Pre�x

400 Series Tilt-Wash

Double-Hung TWPicture DHPTransom TWT


Custom Patterns are also available. For more information on Andersen® divided light, see pages 2-3.

29


Vertical Section(High-Performance™ Low-E4® Impact-Resistant Glass)

Horizontal Section(High-Performance™ Low-E4® Impact-Resistant Glass)

Vertical Section(Standard High-Performance™ Low-E4® glass with PG Upgrade)

Horizontal Section(Standard High-Performance™ Low-E4® glass with PG Upgrade)

Lower sash

Upper sash

Clea

r Opg

.He

ight

Unit

Dim

ensi

on H

eigh

t

Min

imum

Rou

gh O

peni

ng H

eigh

t

Min

imum

Rou

gh O

peni

ng H

eigh

t

Sill stop to sub�oor dimension

1/2" (13)

2-7/16" (62)4-5/16"(110)

3/8" (10)

3/8" (10)

1-3/8" (35)

11/16" (17)

1-1/2" (38)

High-Performance™

Low-E4® impact-resistant glass

2-7/16" (62)

Lower sash inopen position

4-1/2" (114)1-5/16" (33)

4-1/2" (114)1-5/16" (33)

Head

Check Rail

Sill

Sill

Unit

Dim

ensi

on H

eigh

t StandardHigh-Performance™ Low-E4® glass

Wing blade Wing blade retracted for wash mode

Standard High-Performance™ Low-E4® glass

Head

Check Rail

1-7/8"(37)

1-7/8"(37)

1/4" (6) 1/4" (6)

1-5/16"(33)

4-1/

2" (1

14)

1-5/16"(33)

4-1/

2" (1

14)

JambJamb

3-5/16" (84)

1-7/8"(37)

1-7/8"(37)

Clear Opg. Width


Min. Rough Opg. Width

Clear Opg. Width


Min. Rough Opg. Width

1/4" (6)

Jamb

1/4" (6)

Jamb

• Rough opening dimensions may need to be increased to allow for use of building wraps, �ashing, sill panning, brackets, fasteners or other items. See page 7 for more details.• Light colored areas are basic parts furnished by Andersen. Dark colored areas are recommended Andersen parts to complete unit assembly and must be speci�cally ordered.

400

T

ılt-W

ash

Doub

le-Hu

ngW

indow

s


30

Transom Unit and Rough Opening Details Scale 1-1/2" = 1'-0" (1:8)

Picture Unit and Rough Opening Details Scale 1-1/2" = 1'-0" (1:8)





1-5/16" (33)

2-7/16" (62)

2-7/16" (62)

4-1/2" (114)

UnobstructedGlass Width


Minimum Rough Opening Width1/4" (6)

1/4" (6)

Jamb Jamb

1-5/16" (33) 4-1/2" (114)

Unob

str.

Glas

s

Unit

Dim

ensi

on H

eigh

t

Min

imum

Rou

gh O

peni

ng H

eigh

t

1/2" (13)

2-7/16" (62)

HeadOptional Andersen® stool

Sill

5/8" (16)

1-1/2" (38)

2-7/16" (62)

Joining Details Scale 1-1/2" = 1'-0" (1:8)

Andersen® LVL Reinforced Mullion Tilt-wash units joined using Andersen LVL (Laminated Veneer Lumber) reinforced joining materials. For applications that require reinforcement for lateral loads. Andersen LVL reinforced joining materials can be used for mullion and transom joining.

Support Mullion Joining basic tilt-wash units using a vertical support (supplied by others) between units. Exterior �ller and vinyl trim are furnished when speci�ed.

• Rough opening dimensions may need to be increased to allow for use of building wraps, �ashing, sill panning, brackets, fasteners or other items. See page 7 for more details.• Light colored areas are basic parts furnished by Andersen. Dark colored areas are recommended Andersen parts to complete unit assembly and must be speci�cally ordered.

3/4" (19)

Unit Dim. Unit Dim.

Jamb Jamb1-11/16" (43)

2" (51) (Ref.)

Unit Dim. Unit Dim.

Jamb Jamb

Picture windows are not available with monolithic impact-resistant glass.

1-5/16" (33)

4-1/2" (114)

Unobstr.Glass



3-5/16"(84)

3-5/16"(84)

3-5/16"(84)

3-5/16"(84)

1/4" (6)

1/4" (6)

Jamb JambUnit

Dim

ensi

on H

eigh

t

Min

imum

Rou

gh O

peni

ng H

eigh

t

Head

1-5/16" (33) 4-1/2" (114)

Unob

str.

Glas

s

Sill

1/4" (6)

5/16" (8)

31

Opening Specifications for Tilt-Wash Basic Sizes

Unit NumberClear Opg.

Sq. Ft. (m2)


GlassSq. Ft. (m2)


Lineal Ft. (mm)Vent

Sq. Ft. (m2)




WidthInches (mm)

DepthInches (mm)

TW18210 1.52 (0.141) 17-7/8" (454) 12-1/4" (311) 2.90 (0.269) 10' 5" (3175) 1.78 (0.165) 49-3/4" (1264) 5.53 (0.514)TW1832 1.77 (0.164) 17-7/8" (454) 14-1/4" (362) 3.32 (0.308) 11' 1" (3378) 2.03 (0.189) 45-3/4" (1162) 6.14 (0.570)TW1836 2.02 (0.187) 17-7/8" (454) 16-1/4" (413) 3.74 (0.347) 11' 9" (3581) 2.28 (0.212) 41-3/4" (1060) 6.74 (0.626)TW18310 2.27 (0.210) 17-7/8" (454) 18-1/4" (464) 4.15 (0.386) 12' 5" (3785) 2.53 (0.235) 37-3/4" (959) 7.34 (0.682)TW1842 2.51 (0.234) 17-7/8" (454) 20-1/4" (514) 4.57 (0.425) 13' 1" (3988) 2.78 (0.258) 33-3/4" (857) 7.94 (0.737)TW1846 2.76 (0.257) 17-7/8" (454) 22-1/4" (565) 4.98 (0.463) 13' 9" (4191) 3.02 (0.281) 29-3/4" (756) 8.54 (0.793)TW18410 3.01 (0.280) 17-7/8" (454) 24-1/4" (616) 5.40 (0.502) 14' 5" (4394) 3.27 (0.304) 25-3/4" (654) 9.14 (0.849)TW1852 3.26 (0.303) 17-7/8" (454) 26-1/4" (667) 5.81 (0.540) 15' 1" (4597) 3.52 (0.327) 21-3/4" (552) 9.74 (0.905)TW1856 3.51 (0.326) 17-7/8" (454) 28-1/4" (718) 6.23 (0.579) 15' 9" (4801) 3.77 (0.350) 17-3/4" (451) 10.34 (0.961)TW18510 3.76 (0.349) 17-7/8" (454) 30-1/4" (768) 6.65 (0.618) 16' 5" (5004) 4.02 (0.373) 13-3/4" (349) 10.94 (1.016)TW1862 4.00 (0.372) 17-7/8" (454) 32-1/4" (819) 7.06 (0.656) 17' 1" (5207) 4.26 (0.396) 9-3/4" (248) 11.54 (1.072)TW20210 1.86 (0.173) 21-7/8" (556) 12-1/4" (311) 3.68 (0.342) 11' 5" (3480) 2.18 (0.203) 49-3/4" (1264) 6.56 (0.609)TW2032 2.17 (0.201) 21-7/8" (556) 14-1/4" (362) 4.21 (0.391) 12' 1" (3683) 2.48 (0.230) 45-3/4" (1162) 7.27 (0.675)TW2036 2.44 (0.227) 21-7/8" (556) 16-1/4" (413) 4.73 (0.439) 12' 9" (3886) 2.79 (0.259) 41-3/4" (1060) 7.98 (0.742)TW20310 2.77 (0.258) 21-7/8" (556) 18-1/4" (464) 5.26 (0.489) 13' 5" (4090) 3.09 (0.287) 37-3/4" (959) 8.69 (0.808)TW2042 3.08 (0.286) 21-7/8" (556) 20-1/4" (514) 5.79 (0.538) 14' 1" (4293) 3.40 (0.316) 33-3/4" (857) 9.41 (0.874)TW2046 3.38 (0.314) 21-7/8" (556) 22-1/4" (565) 6.31 (0.586) 14' 9" (4496) 3.70 (0.344) 29-3/4" (756) 10.12 (0.940)TW20410 3.68 (0.342) 21-7/8" (556) 24-1/4" (616) 6.84 (0.635) 15' 5" (4699) 4.00 (0.372) 25-3/4" (654) 10.83 (1.006)TW2052 3.99 (0.370) 21-7/8" (556) 26-1/4" (667) 7.37 (0.685) 16' 1" (4902) 4.31 (0.400) 21-3/4" (552) 11.54 (1.072)TW2056 4.29 (0.399) 21-7/8" (556) 28-1/4" (718) 7.89 (0.733) 16' 9" (5105) 4.61 (0.428) 17-3/4" (451) 12.25 (1.138)TW20510 4.60 (0.427) 21-7/8" (556) 30-1/4" (768) 8.42 (0.782) 17' 5" (5309) 4.92 (0.457) 13-3/4" (349) 12.96 (1.204)TW2062 4.90 (0.455) 21-7/8" (556) 32-1/4" (819) 8.95 (0.831) 18' 1" (5512) 5.22 (0.485) 9-3/4" (248) 13.68 (1.271)TW24210 2.20 (0.204) 25-7/8" (657) 12-1/4" (311) 4.46 (0.414) 12' 5" (3785) 2.58 (0.240) 49-3/4" (1264) 7.58 (0.704)TW2432 2.56 (0.238) 25-7/8" (657) 14-1/4" (362) 5.09 (0.473) 13' 1" (3988) 2.94 (0.273) 45-3/4" (1162) 8.40 (0.781)TW2436 2.92 (0.271) 25-7/8" (657) 16-1/4" (413) 5.73 (0.532) 13' 9" (4191) 3.30 (0.307) 41-3/4" (1060) 9.23 (0.857)TW24310 3.28 (0.305) 25-7/8" (657) 18-1/4" (464) 6.37 (0.592) 14' 5" (4394) 3.66 (0.340) 37-3/4" (959) 10.05 (0.934)TW2442 3.64 (0.338) 25-7/8" (657) 20-1/4" (514) 7.01 (0.651) 15' 1" (4597) 4.02 (0.373) 33-3/4" (857) 10.87 (1.010)TW2446 4.00 (0.371) 25-7/8" (657) 22-1/4" (565) 7.65 (0.711) 15' 9" (4801) 4.38 (0.407) 26-3/4" (756) 11.70 (1.087)TW24410 4.36 (0.405) 25-7/8" (657) 24-1/4" (616) 8.28 (0.769) 16' 5" (5004) 4.74 (0.440) 25-3/4" (654) 12.52 (1.163)TW2452 4.72 (0.438) 25-7/8" (657) 26-1/4" (667) 8.92 (0.829) 17' 1" (5207) 5.10 (0.474) 21-3/4" (552) 13.34 (1.240)TW2456 5.08 (0.472) 25-7/8" (657) 28-1/4" (718) 9.56 (0.888) 17' 9" (5410) 5.45 (0.506) 17-3/4" (451) 14.17 (1.316)TW24510 5.44 (0.505) 25-7/8" (657) 30-1/4" (768) 10.20 (0.947) 18' 5" (5614) 5.81 (0.540) 13-3/4" (349) 14.99 (1.392)TW2462* 5.80 (0.538) 25-7/8" (657) 32-1/4" (819) 10.84 (1.007) 19' 1" (5817) 6.17 (0.573) 9-3/4" (248) 15.81 (1.469)TW26210 2.37 (0.220) 27-7/8" (708) 12-1/4" (311) 4.84 (0.450) 12' 11" (3937) 2.78 (0.258) 49-3/4" (1264) 8.09 (0.752)TW2632 2.76 (0.256) 27-7/8" (708) 14-1/4" (362) 5.54 (0.515) 13' 7" (4140) 3.17 (0.295) 45-3/4" (1162) 8.97 (0.833)TW2636 3.15 (0.292) 27-7/8" (708) 16-1/4" (413) 6.23 (0.579) 14' 3" (4343) 3.55 (0.330) 41-3/4" (1060) 9.85 (0.915)TW26310 3.53 (0.382) 27-7/8" (708) 18-1/4" (464) 6.92 (0.643) 14' 11" (4547) 3.94 (0.366) 37-3/4" (959) 10.73 (0.997)TW2642 3.92 (0.364) 27-7/8" (708) 20-1/4" (514) 7.62 (0.708) 15' 7" (4750) 4.33 (0.402) 33-3/4" (857) 11.61 (1.079)TW2646 4.31 (0.400) 27-7/8" (708) 22-1/4" (565) 8.31 (0.772) 16' 3" (4953) 4.71 (0.438) 29-3/4" (756) 12.49 (1.160)TW26410 4.70 (0.436) 27-7/8" (708) 24-1/4" (616) 9.01 (0.837) 16' 11" (5156) 5.10 (0.474) 25-3/4" (654) 13.36 (1.241)TW2652 5.08 (0.472) 27-7/8" (708) 26-1/4" (667) 9.70 (0.901) 17' 7" (5359) 5.49 (0.510) 21-3/4" (552) 14.24 (1.323)TW2656 5.47 (0.508) 27-7/8" (708) 28-1/4" (718) 10.39 (0.963) 18' 3" (5563) 5.88 (0.546) 17-3/4" (451) 15.12 (1.405)TW26510* 5.86 (0.544) 27-7/8" (708) 30-1/4" (768) 11.09 (1.030) 18' 11" (5766) 6.26 (0.582) 13-3/4" (349) 16.00 (1.486)TW2662* 6.24 (0.580) 27-7/8" (708) 32-1/4" (819) 11.78 (1.094) 19' 7" (5969) 6.65 (0.618) 9-3/4" (248) 16.88 (1.568)TW28210 2.54 (0.236) 29-7/8" (759) 12-1/4" (311) 5.23 (0.486) 13' 5" (4090) 2.98 (0.277) 49-3/4" (1264) 8.61 (0.800)TW2832 3.00 (0.275) 29-7/8" (759) 14-1/4" (362) 5.98 (0.556) 14' 1" (4293) 3.39 (0.315) 45-3/4" (1162) 9.54 (0.886)TW2836 3.37 (0.313) 29-7/8" (759) 16-1/4" (413) 6.73 (0.625) 14' 9" (4496) 3.81 (0.354) 41-3/4" (1060) 10.47 (0.973)TW28310 3.79 (0.352) 29-7/8" (759) 18-1/4" (464) 7.48 (0.695) 15' 5" (4699) 4.22 (0.392) 37-3/4" (959) 11.41 (1.060)TW2842 4.20 (0.390) 29-7/8" (759) 20-1/4" (514) 8.23 (0.765) 16' 1" (4902) 4.64 (0.431) 33-3/4" (857) 12.34 (1.146)TW2846 4.62 (0.429) 29-7/8" (759) 22-1/4" (565) 8.98 (0.834) 16' 9" (5105) 5.05 (0.469) 29-3/4" (756) 13.28 (1.234)TW28410 5.03 (0.467) 29-7/8" (759) 24-1/4" (616) 9.73 (0.904) 17' 5" (5309) 5.47 (0.508) 25-3/4" (654) 14.21 (1.320)TW2852 5.45 (0.506) 29-7/8" (759) 26-1/4" (667) 10.48 (0.974) 18' 1" (5512) 5.88 (0.546) 21-3/4" (552) 15.14 (1.407)TW2856* 5.86 (0.544) 29-7/8" (759) 28-1/4" (718) 11.22 (1.042) 18' 9" (5715) 6.30 (0.585) 17-3/4" (451) 16.08 (1.494)TW28510* 6.28 (0.583) 29-7/8" (759) 30-1/4" (768) 11.97 (1.112) 19' 5" (5918) 6.71 (0.623) 13-3/4" (349) 17.01 (1.580)TW2862* 6.69 (0.622) 29-7/8" (759) 32-1/4" (819) 12.72 (1.182) 20' 1" (6121) 7.13 (0.662) 9-3/4" (248) 17.95 (1.668)

* These units meet or exceed the following dimensions: clear openable area of 5.7 sq. ft., clear openable width of 20" and clear openable height of 24."

400

T

ılt-W

ash

Doub

le-Hu

ngW

indow

s

32

Opening Specifications for Tilt-Wash Basic Sizes – Continued

Unit NumberClear Opg.

Sq. Ft. (m2)


GlassSq. Ft. (m2)


Lineal Ft. (mm)Vent

Sq. Ft. (m2)




WidthInches (mm)

DepthInches (mm)

TW210210 2.71 (0.252) 31-7/8" (809) 12-1/4" (311) 5.62 (0.522) 13' 11" (4242) 3.18 (0.295) 49-3/4" (1264) 9.12 (0.847)TW21032 3.15 (0.293) 31-7/8" (809) 14-1/4" (362) 6.42 (0.596) 14' 7" (4445) 3.62 (0.336) 45-3/4" (1162) 10.11 (0.939)TW21036 3.65 (0.340) 31-7/8" (809) 16-1/4" (413) 7.23 (0.672) 15' 3" (4648) 4.06 (0.377) 41-3/4" (1060) 11.10 (1.031)TW210310 4.04 (0.375) 31-7/8" (809) 18-1/4" (464) 8.03 (0.746) 15' 11" (4852) 4.51 (0.419) 37-3/4" (959) 12.09 (1.123)TW21042 4.48 (0.416) 31-7/8" (809) 20-1/4" (514) 8.84 (0.821) 16' 7" (5055) 4.95 (0.460) 33-3/4" (857) 13.08 (1.215)TW21046 4.93 (0.458) 31-7/8" (809) 22-1/4" (565) 9.64 (0.896) 17' 3" (5258) 5.39 (0.501) 29-3/4" (756) 14.07 (1.307)TW210410 5.37 (0.500) 31-7/8" (809) 24-1/4" (616) 10.45 (0.971) 17' 11" (5461) 5.83 (0.542) 25-3/4" (654) 15.05 (1.398)TW21052* 5.81 (0.540) 31-7/8" (809) 26-1/4" (667) 11.25 (1.045) 18' 7" (5664) 6.28 (0.583) 21-3/4" (552) 16.04 (1.490)TW21056* 6.25 (0.581) 31-7/8" (809) 28-1/4" (718) 12.06 (1.120) 19' 3" (5867) 6.72 (0.624) 17-3/4" (451) 17.03 (1.587)TW210510* 6.70 (0.622) 31-7/8" (809) 30-1/4" (768) 12.86 (1.195) 19' 11" (6071) 7.16 (0.665) 13-3/4" (349) 18.02 (1.674)TW21062* 7.14 (0.663) 31-7/8" (809) 32-1/4" (819) 13.67 (1.270) 20' 7" (6274) 7.60 (0.706) 9-3/4" (248) 19.01 (1.766)TW30210 2.88 (0.268) 33-7/8" (860) 12-1/4" (311) 6.01 (0.558) 14' 5" (4394) 3.38 (0.314) 49-3/4" (1264) 9.63 (0.895)TW3032 3.35 (0.311) 33-7/8" (860) 14-1/4" (362) 6.87 (0.638) 15' 1" (4597) 3.85 (0.358) 45-3/4" (1162) 10.67 (0.991)TW3036 3.82 (0.355) 33-7/8" (860) 16-1/4" (413) 7.73 (0.718) 15' 9" (4801) 4.32 (0.401) 41-3/4" (1060) 11.72 (1.089)TW30310 4.30 (0.400) 33-7/8" (860) 18-1/4" (464) 8.59 (0.798) 16' 5" (5004) 4.79 (0.445) 37-3/4" (959) 12.76 (1.185)TW3042 4.76 (0.443) 33-7/8" (860) 20-1/4" (514) 9.45 (0.878) 17' 1" (5207) 5.26 (0.489) 33-3/4" (857) 13.81 (1.283)TW3046 5.23 (0.486) 33-7/8" (860) 22-1/4" (565) 10.31 (0.958) 17' 9" (5410) 5.73 (0.532) 29-3/4" (756) 14.85 (1.380)TW30410* 5.70 (0.530) 33-7/8" (860) 24-1/4" (616) 11.17 (1.038) 18' 5" (5614) 6.20 (0.576) 25-3/4" (654) 15.90 (1.477)TW3052* 6.18 (0.576) 33-7/8" (860) 26-1/4" (667) 12.03 (1.118) 19' 1" (5817) 6.67 (0.620) 21-3/4" (552) 16.95 (1.575)TW3056* 6.65 (0.617) 33-7/8" (860) 28-1/4" (718) 12.89 (1.198) 19' 9" (6020) 7.14 (0.663) 17-3/4" (451) 17.99 (1.671)TW30510* 7.12 (0.661) 33-7/8" (860) 30-1/4" (768) 13.75 (1.277) 20' 5" (6223) 7.61 (0.707) 13-3/4" (349) 19.04 (1.769)TW3062* 7.59 (0.705) 33-7/8" (860) 32-1/4" (819) 14.61 (1.357) 21' 1" (6426) 8.08 (0.751) 9-3/4" (248) 20.08 (1.865)TW34210 3.22 (0.299) 37-7/8" (962) 12-1/4" (311) 6.79 (0.631) 15' 5" (4699) 3.78 (0.351) 49-3/4" (1264) 10.65 (0.989)TW3432 3.75 (0.348) 37-7/8" (962) 14-1/4" (362) 7.76 (0.721) 16' 1" (4902) 4.30 (0.399) 45-3/4" (1162) 11.81 (1.097)TW3436 4.27 (0.397) 37-7/8" (962) 16-1/4" (413) 8.73 (0.811) 16' 9" (5105) 4.83 (0.449) 41-3/4" (1060) 12.97 (1.205)TW34310 4.80 (0.446) 37-7/8" (962) 18-1/4" (464) 9.70 (0.901) 17' 5" (5309) 5.35 (0.497) 37-3/4" (959) 14.12 (1.312)TW3442 5.33 (0.495) 37-7/8" (962) 20-1/4" (514) 10.67 (0.991) 18' 1" (5512) 5.88 (0.546) 33-3/4" (857) 15.28 (1.420)TW3446 5.85 (0.544) 37-7/8" (962) 22-1/4" (565) 11.64 (1.081) 18' 9" (5715) 6.41 (0.596) 29-3/4" (756) 16.43 (1.526)TW34410* 6.38 (0.593) 37-7/8" (962) 24-1/4" (616) 12.61 (1.172) 19' 5" (5918) 6.93 (0.644) 25-3/4" (654) 17.59 (1.634)TW3452* 6.90 (0.641) 37-7/8" (962) 26-1/4" (667) 13.58 (1.262) 20' 1" (6121) 7.46 (0.693) 21-3/4" (552) 18.75 (1.742)TW3456* 7.43 (0.690) 37-7/8" (962) 28-1/4" (718) 14.55 (1.352) 20' 9" (6325) 8.00 (0.743) 17-3/4" (451) 19.90 (1.849)TW34510* 7.96 (0.739) 37-7/8" (962) 30-1/4" (768) 15.53 (1.443) 21' 5" (6528) 8.51 (0.791) 13-3/4" (349) 21.06 (1.957)TW3462* 8.48 (0.788) 37-7/8" (962) 32-1/4" (819) 16.50 (1.533) 21' 1" (6731) 9.04 (0.840) 9-3/4" (248) 22.22 (2.064)TW38210 3.56 (0.331) 41-7/8" (1064) 12-1/4" (311) 7.56 (0.702) 16' 5" (5004) 4.17 (0.387) 49-3/4" (1264) 11.68 (1.085)TW3832 4.14 (0.385) 41-7/8" (1064) 14-1/4" (362) 8.64 (0.803) 17' 1" (5207) 4.76 (0.442) 45-3/4" (1162) 12.94 (1.202)TW3836 4.73 (0.439) 41-7/8" (1064) 16-1/4" (413) 9.72 (0.903) 17' 9" (5410) 5.34 (0.496) 41-3/4" (1060) 14.21 (1.320)TW38310 5.31 (0.493) 41-7/8" (1064) 18-1/4" (464) 10.81 (1.004) 18' 5" (5614) 5.92 (0.550) 37-3/4" (959) 15.48 (1.438)TW3842 5.89 (0.547) 41-7/8" (1064) 20-1/4" (514) 11.89 (1.105) 19' 1" (5817) 6.50 (0.604) 33-3/4" (857) 16.75 (1.556)TW3846 6.47 (0.601) 41-7/8" (1064) 22-1/4" (565) 12.97 (1.205) 19' 9" (6020) 7.08 (0.658) 29-3/4" (756) 18.01 (1.673)TW38410* 7.05 (0.655) 41-7/8" (1064) 24-1/4" (616) 14.05 (1.305) 20' 5" (6223) 7.66 (0.712) 25-3/4" (654) 19.28 (1.791)TW3852* 7.63 (0.709) 41-7/8" (1064) 26-1/4" (667) 15.14 (1.407) 21' 1" (6426) 8.25 (0.766) 21-3/4" (552) 20.55 (1.909)TW3856* 8.22 (0.763) 41-7/8" (1064) 28-1/4" (718) 16.22 (1.507) 21' 9" (6629) 8.83 (0.820) 17-3/4" (451) 21.62 (2.009)TW38510* 8.80 (0.817) 41-7/8" (1064) 30-1/4" (768) 17.30 (1.607) 22' 5" (6833) 9.41 (0.874) 13-3/4" (349) 23.08 (2.144)TW3862* 9.38 (0.871) 41-7/8" (1064) 32-1/4" (819) 18.38 (1.708) 23' 1" (7036) 9.99 (0.928) 9-3/4" (248) 24.35 (2.262)

* These units meet or exceed the following dimensions: clear openable area of 5.7 sq. ft., clear openable width of 20" and minimum height of clear openable height of 24."


Specialty Windows

This full collection of stylish, graceful enhancements can be used in a variety of applications. They can make a

signature statement — or provide a delicate lighting accent. Best of all, from circles to arches to custom-designed

picture windows, you’ll get the same uncompromised quality and value you expect from any Andersen® product.

Section Reference

Circle Top™ ........................... 36

Elliptical............................... 37

Circle and Oval .................... 38

Flexiframe® ........................... 39

Arch ..................................... 40

Springline™ .......................... 42

Enhancement ...................... 44

Springline™ Flanker .............. 45

Custom Arch ........................ 45



400

S

pecia

ltyW

indo

ws

34

Features

Specialty Windows



FRame

Wood frame members are treated with a water- repellent wood preservative for long-lasting* protection and performance. Radii are made of laminated, continuous maple select hardwood (without finger joints), offering improved strength and appearance.

The lineal sections of the jamb and sill on Andersen® Flexiframe®, custom arch, arch and enhancement windows are covered with a low-maintenance, glass fiber reinforced composite. The arched head members, and Springline™ units, are covered with stretch formed coated aluminum. Exterior finishes include four neutral colors. Specify White, Sandtone, Terratone® or Forest Green color.

The vinyl anchoring flange on Flexiframe, custom arch, arch, Springline™ and enhancement units extends 1-1/4" (32) around the entire perimeter of the unit (not applied). It helps secure the unit to the structure.

The fastening system uses 1-1/2" (38) by 3"

(76) stainless steel installation clips. The installation clips are screwed to the frame and fastened to the rough opening for secure installation. Optional 6" clips are available for use with pre-applied extension jambs.

Springline units are installed through the frame with #10 x 3" screws.

Pre-formed rigid vinyl sheath on the Andersen Circle Top,™ quarter round, elliptical, circle and oval window frames forms a full perimeter flange for sealing the unit to the structure.

Inside trim stop is made of unfinished clear pine. (Arch stops are select hardwood.) Arched trim stops are made with quality, full-length, select hardwood laminations. Units are shipped with the trim stops tacked on, so removal is easy, expediting finishing and joining procedures.

Unfinished inside wood glazing stop helps secure the glass in place. Arched glazing stops are made with full-length select hardwood laminations.

Interior wood stops are secured to frame using

1-1/2" 16-gauge crown staples instead of nails.

† On units up to 50 sq. ft.

^ On units up to 30 sq. ft.

Arch Window

Circle Top™ Window

Andersen Circle Top™, quarter round, elliptical, circle and oval windows are covered with a seamless rigid vinyl (PVC) pre-formed sheath. Low-maintenance exterior cladding provides long- lasting* beauty in four exterior finish options. Specify White, Sandtone, Terratone® or Forest Green color.

GlaSS


• High-Performance™ Low-E4®

impact-resistant glass†

• High-Performance™ Low-E4® Sun impact-resistant glass†

• High-Performance™ Low-E4® SmartSun™ impact-resistant glass†

• High-Performance™ Low-E4® tempered impact-resistant glass†

• High-Performance™ Low-E4® Sun tempered impact-resistant glass†

• High-Performance™ Low-E4® SmartSun™ tempered impact-resistant glass†

• Monolithic impact-resistant glass^

• Monolithic tinted impact-resistant glass^

* For complete information on our limited

warranties, visit andersenwindows.com or contact your Andersen supplier.

exterior Interior

pinewhite


Specify a unit exterior color option and an interior finish option to complete your order.

Circle/OvalWindowFlexiframe®Window Springline™Window


35










* Select hardwoods for specialty window interior arch casing include Hard Maple, Red Maple, European Birch, White Poplar and White Aspen. The specific species used will be dependent upon availability.

"Frank Lloyd Wright" is a registered trademark of the Frank Lloyd Wright Foundation.


Interior Arch CasingAvailable in colonial or ranch styles. Two transition blocks come with each arch casing. Arch window casings come with plinth blocks. Pine casings and additional profiles are also available. For easy integration and consistency, casing dimensions are consistent with Wood Moulding and Millwork Producers Association specifications.

2-1/4" (57) Colonial style, in oak and select hardwoods.* WM366.



2-1/4" (57) Ranch style in oak and select hardwoods.* WM324.

2-1/2" (64) Ranch style in oak and select hardwoods.* WM315.

Plinth Blocks For enhancing casing transitions. Decorated with a radial sunburst, or use the reverse side flush face.

For arch windows: 2-7/8" (73) x 4" (102) size for use with 2-1/4" (57) and 2-1/2" (64) casing, 3-7/8" (98) x 5-1/4" (133) for use with 3-1/2" (89) casing.

For Circle Top,™ elliptical, circle and oval windows: 2-7/8" (73) size for use with 2-1/4" (57) and 2-1/2" (64) casing, 3-7/8" (98) size for use with 3-1/2" (89) casing.

Key Block Excellent for creating unique trim designs or accents at arch casing transitions. A key block is an option for Andersen circle and oval windows. Not available on units with monolithic glass.

Transition Piece Two transition pieces come with the interior arch casing/ extension jambs, providing a beautiful accent for circle and oval windows.

FRame

Extension JambsSpecify extension jambs when ordering.

Standard unit jamb width is 2-7/8" (73), except for elliptical and double-hung Circle Top™ units, which are 4-1/2" (114).

Pine (or continuous laminated select hardwood) extension jambs are pre-drilled and available for the following wall thicknesses:

• 4-9/16" (116) • 5-1/4" (133) • 6-9/16" (167) • 7-1/8" (181) (not pre-drilled)

Some sizes may be pine veneer. Springline™ window extension jambs and transition pieces are applied when ordered with the unit (key component block is also applied to units with a 48" (1219) radius).

Auxiliary Extension JambsFor joining arch windows over casement or alongside awning windows. Available for the following wall thicknesses:

• 4-9/16" (116) • 5-1/4" (133) • 6-9/16" (167) • 7-1/8" (181)

InStallatIon SyStem



GlaSS



400

S

pecia

ltyW

indo

ws

Specialty Windows

36

Table of Basic Circle Top™ Window—Casement/Awning Sizes Scale 1/8" = 1'-0" (1:96)

NOTE: Picture window grille alignment may not coincide with Circle Top™ grille patternwhen transom joined.

Special order picture window grilles to align with CT2 and CT3 are available. Contact your Andersen supplier.

• For custom grille alignment options for specialty windows, contact your Andersen supplier or visit andersenwindows.com/grilles.


• Andersen® art glass panels are available for all sizes on this page.




‡ Contact your Andersen supplier for availability of Andersen® art glass panels for these sizes.

Renaissance Pattern

Sunburst Pattern

Renaissance Pattern

Sunburst Pattern

Renaissance Pattern

Sunburst Pattern

5'-11 7/8"

6'-0 3/8"

67 1/4"

4'-8 1/2"

4'-9"

4'-0"

4'-0 1/2"

43 3/8" 51 7/8"

1'-2

3/ 8

"

1'-2

7 /8"

9 3 /

4"

1'-4

1 /2"

1'-5

"

117 /

8"

2'-2

5 /16

"

21 11

/ 16"

2'-2

7 /8"

2'-6

9 /16

"

25 15

/ 16"

2'-7

1 /8"

3'-2

1/ 4

"

3'-2

3/ 4

"

33 5

/ 8"

5'-2 3/4"

5'-3 1/4"

58 1/8"

2'-9

5/ 8

"

2'-1

0 1 /

8"

29"

2'-4 3/8"

2'-4 7/8"

23 3/4"

2'-4

3 /8"

2'-4

7 /8"

23 3

/ 4"

2'-11 15/16"

3'-0 1/2"

31 5 /16"

2'-1

115 /

16"

3'-0

1/ 2

"

31 5

/ 16"

2'-7 1/2"

2'-8"

26 7/8"

2'-7

1 /2"

2'-8

"

26 7

/ 8"

1'-6

"

13 7 /

16"

1-6

1 /2"

1'-8

1/ 4

"

1'-8

3 /4"

15 5

/ 8"

2'-0 1/8"

2'-0 5/8"

19 1/2"

2'-4 3/8"

2'-4 7/8"

23 3/4"

2'-11 15/16"

3'-0 1/2"

31 5/16"

2'-7 1/2"

2'-8"

26 7/8"

2'-0 1/8"

2'-0 5/8"

19 1/2"

2'-0

1/ 8

"

2'-0

5 /8"

19 1

/ 2"

(795)

(248

)

(302

)

(1102)

(1232)

(1219)

(1318)

(1448)

(1435)

(1708)

(1838)

(1826)

(854

)

(984

)

(972

)

(1476)

(1607)

(1594)

(737

)

(867

)

(854

)

(659

)

(791

)

(776

)

(551

)

(683

)

(668

)

(603)

(733)

(721)

(927)

(913)

(378

)

(365

)

(603

)

(733

)

(721

)

(432

)

(419

)

(795

)

(927

)

(913

)

(683)

(813)

(800)

(683

)

(813

)

(800

)

(341

)

(470

)

(458

)

(397

)

(527

)

(514

)

(495)

(625)

(613)

(795)(603)

(733)

(721)

(927)

(913)

(683)

(813)

(800)

(495)

(625)

(613)

(495

)

(625

)

(613

)

CTQCW1 CTQCX1 ‡

CTCW2 CTC3CTC2

CTCW1CTC1

CTQC1 CTQA3

CTCXW1CTCX1 ‡

CTCX2 ‡

Table of Basic Circle Top™ Window—Double-Hung Sizes Scale 1/8" = 1'-0" (1:96)

2'-1 5/8"


Unit Dimension

2'-2 1/8"

20 3/8"

6'-3 5/16"

6'-3 7/8"

70 1/16"

2'-5 5/8"

2'-6 1/8"

24 3/8"

2'-9 5/8"

2'-10 1/8"

28 3/8"

3'-1 5/8"

3'-2 1/8"

32 3/8"

3'-5 5/8"

3'-6 1/8"

36 3/8"

10 3 /

16"

1'-3

3 /4"

1'-3

3 /16

"

1'-5

3 /4"

12 3 /

16"

1'-7

3 /16

"

1'-7

3 /4"

14 3 /

16"

1'-9

3 /16

"

1'-9

3 / 4"

16 3 /

16"

18 3 /

16"

1'-11

3 /4 "

1'-1

1 3/ 1

6"

3'-4

"

3'-4

1/ 2

"

34 1

/ 4"

3'-0

"

5'-7 7/8"

62

31

1'-5

3 /16

"

5'-7 5/16"

62 1/16"

Renaissance Pattern

Sunburst Pattern

Renaissance Pattern

Sunburst Pattern

3'-0

1/ 2

"

"

Unobstructed Glass


Unit Dimension

Unobstructed Glass


Unit Dimension

Unobstructed Glass


Unit Dimension

Unobstructed Glass


Unit Dimension

Unobstructed Glass

(259

)

(400

)

(386

)

(518)

(664)

(651)

(1780)

(1927)

(1913)

(619)

(765)

(752)

(721)

(867)

(854)

(822)

(968)

(956)

(924)

(1070)

(1057)

(310

)

(451

)

(437

)

(360

)

(502

)

(487

)

(411

)

(552

)

(538

)

(462

)

(603

)

(589

)

(870

)

(102

9)

(101

6)

(1576)

(1724)

(1710)

(787

)

(927

)

(914

)

CTN20

CTN30-2CTN28-2

CTN24 CTN28 CTN30 CTN34

Colonial Pattern Example

Sizes on this page are shown with Renaissance and Sunburst grille patterns.

Colonial Grille Patterns are also available. For more information on Andersen divided light, see pages 2-3 or visit andersenwindows.com/grilles.

37

Circle Top™ Window–Casement/Awning Glass Area

Unit NumberGlass

Sq. Ft. (m2)CTQC1 1.9 (0.177)CTC1 1.0 (0.093)CTQCW1 3.0 (0.279)CTCW1 1.5 (0.139)CTQA3 5.2 (0.483)CTCXW1 2.7 (0.251)CTC2 5.1 (0.474)CTCW2 7.3 (0.678)CTC3 12.3 (1.143)CTQCX1 3.8 (0.353)CTCX1 2.0 (0.186)CTCX2 9.3 (0.864)

Circle Top™ Window–Double-Hung Glass Area

Unit NumberGlass

Sq. Ft. (m2)CTN20 1.1 (0.102)CTN24 1.6 (0.149)CTN28 2.2 (0.204)CTN30 2.8 (0.260)CTN34 3.6 (0.335)CTN28-2 10.5 (0.975)CTN30-2 13.4 (1.245)

Table of Basic Elliptical Window Sizes Scale 1/8" = 1'-0" (1:96)


Vertical SectionCircle Top™ (Casement/Awning)

(High-Performance™ Low-E4®

Impact-Resistant Glass)

Vertical SectionCircle Top™ (Double-Hung)(High-Performance™ Low-E4®


Vertical SectionElliptical



Vertical SectionQuarter Round (Casement/Awning)



* 4-9/16" measurement is from the backside of the anchoring �ange to edge of extension jamb.

• Renaissance and Sunburst patterns are available in Finelight™ units, speci�ed divided light or with removable interior grilles.

• For custom grille alignment options for specialty windows, contact your Andersen supplier or visit andersenwindows.com/grilles


• Andersen® art glass panels are available for these sizes.




ET8, FWG & FWHET6, FWG & FWH

ET6, C, PD & NL ET8, C, PD & NL

Standard Grilles / Size Compatibility

6'-0"

Unobstructed Glass


Unit Dimension

1'-4

3/ 4

"

1'-5

3/ 8

"

11 7

/ 8"

66 1/4"

7'-11 1/4"

8'-0"

90 1/4"

1'-9

"

1'-9

5/ 8

"

16 1

/ 8"

5'-11 1/4"

(1683)

(1810)(3

02)

(441

)

(425

)

(410

)

(2292)

(2438)

(2419)

(533

)

(549

)

(1829)

ET6 ET8

Renaissance Pattern

Sunburst Pattern

4-1/2" (114)

Unit

Dim

ensi

on H

eigh

t

Head

Sill

2-1/2"(64)

2"(51)

2-1/8"(54)Un

it Di

men

sion

Hei

ght

Andersen®

extension jambs

4-9/16" (116) Jamb Width*

1-5/16" (33)

2-1/4"(57)

Head

Sill

2-5/8"(67)

2-3/8"(60)

4-1/2" (114)1-5/16"

(33)

1-5/16" (33)

Min

. Rou

gh O

peni

ng H

eigh

t

Min

. Rou

gh O

peni

ng H

eigh

t

Min

. Rou

gh O

peni

ng H

eigh

t

Min

. Rou

gh O

peni

ng H

eigh

t

Unit

Dim

ensi

on H

eigh

t

Head

Sill

Unit

Dim

ensi

on H

eigh

t

Andersen®

extension jambs

Head

Sill

4-9/16" (116) Jamb Width*

1-5/16" (33)

2-1/4"(57)

2-1/4"(57)

Elliptical Glass Area

Unit NumberGlass

Sq. Ft. (m2)ET6 4.3 (0.399)ET8 8.0 (0.743)

400

S

pecia

ltyW

indo

ws

Specialty Windows

38

Basic Unit and Rough Opening Details Scale 3" = 1'-0" (1:4)

Vertical Section - Circle Unit(High-Performance™ Low-E4® Impact-Resistant Glass)

Vertical Section - Oval Unit(High-Performance™ Low-E4® Impact-Resistant Glass)

* 4-9/16" measurement is from

backside of anchoring �ange to

edge of extension jamb.• Rough opening dimensions may

need to be increased to allow for use of building wraps, �ashing, sill panning, brackets, fasteners or other items. See page 7 for more details.

Head

Sill

Optional Andersenkey block

Standard Andersentransition blockfor oval unit

Optional Andersenextension jambs andtransition pieces

Optional Anderseninterior arch casingand transition pieces

Min

imum

Rou

ghOp

enin

g He

ight

4-9/16" (116)Jamb Width*

1-5/16" (33)

Unit

Dim

ensi

on H

eigh

t

Head

Sill

Optional Andersenkey block

Standard Andersentransition blockfor oval unit

Optional Andersenextension jambs andtransition pieces

Optional Anderseninterior arch casingand transition pieces

1/4" (6)

1/4" (6)

Min

imum

Rou

ghOp

enin

g He

ight

4-9/16" (116)Jamb Width*

1-5/16" (33)

Unit

Dim

ensi

on H

eigh

t

1/4" (6)

1/4" (6)

Table of Basic Circle and Oval Unit Sizes Scale 1/8" = 1'-0" (1:96)

Circle Window with Renaissance Grille Pattern

Oval Window with Renaissance Grille Pattern

• Rough opening dimensions may need to be increased to allow for use of building wraps, �ashing, sill panning, brackets, fasteners or other items. See page 7 for more details.• Andersen® art glass panels are available in Classic Series and Artisan Series designs only for all sizes on this page.

Horizontal Installation

Oval windows can be installed either vertically or horizontally.

Unit Dimension


Unobstructed Glass

OVL3048OVL2030OVL1824

OVL4

830

OVL3

020

OVL2

418

3'-0"(914)

3'-0 1/2"(927)

31 3/8"(797)

2'-0"(610)

1'-8 1/4"(514)

15 3/8"(391)

19 3/8"(492)

2'-4

3/ 8

"(7

21)

24"

(610

)

2'-4

7/ 8

"(7

33)

2'-1

1 15

/ 16"

(913

)

31 9

/ 16"

(802

)

3'-0

1/ 2

"(9

27)

4'-8

1/ 2

"(1

435)

4'

-9"

(144

8)

52 1

/ 8"

(132

4)

1'-7 3/4"(502)

2'-0 1/2"(622)

CIR20 CIR24 CIR30

Unit Dimension


Unobstructed Glass31 9/16"(802)

2'-0 1/8"(613)

2'-4 7/8"(733)

2'-4 3/8"(721)

19 3/4"(502)

2'-0 5/8"(625)

24 " (610)

3'-0 1/2"(927)

2'-11 15/16"(913)

Andersen® Key Block KitAvailable in maple or oak. Each kit includes two (2) key blocks andtwo (2) key components, enough to do both sides or top and bottom. Not available for units with monolithic impact-resistant glass.

Installation Examples

In this example two (2) key block kits are used.

Key Block

Dowel

Key ComponentTypical installation of the Andersen key block kit.

NOTE: See installation information starting on page 6.

Custom Pattern ExamplesColonial Pattern Examples

Colonial and Custom Grille speci�ed equal light patterns are also available. For more information on Andersen divided light, see page 2-3 or visit andersenwindows.com/grilles.

CAUTION: In masonry wall construction, provide a minimum of 1/2" clearance from the top of the brick or masonry to the bottom of any portion of the sill. Failure to do so could result in product damage. Fill the void with closed cell foam backer rod and sealant. Be sure to allow for dimensional change of framework.

Circle and Oval Window Glass Area

Unit NumberGlass

Sq. Ft. (m2)CIR20 2.1 (0.195)CIR24 3.0 (0.279)CIR30 5.2 (0.483)OVL1824 1.9 (0.177)OVL2030 3.2 (0.297)OVL3048 8.7 (0.808)

39

Rectangles Rectangles as a category include both squares and rectangles. Flexiframe® rectangle units should be specified by identifying their width and height. Sides of Flexiframe rectangle units may be any dimension between 9" and 120." The overall area defined by the rectangle may not exceed 50 square feet glass dimension.

Sill Detail Scale 1-1/2" = 1'-0" (1:8)

Flexiframe®

Windows

Sill

Glazing sealant

Glass stop

1-3/8" trim stop(included in factory set up)2" trim stop also available

Optional Andersen extension jamb

Nailing �ange

1-3/8" (35)

2-7/8" (73)1-5/16" (33)

Max. Sill Width

Min.Height

Min. Width

Max.Height

Sill Width

Sill toPeak

HeightSideHeight

Height

Width

Sill to Peak Height

Sill Width

Unit Width

Pitch

UnitHeight

LegLength

Leg Width

Sill WidthSill Width

Max.Height

Max.Height

Min.Height

Min.Height

Width

HeightHeight

Width

equilateralhexagon hexagon octagon

angledpentagon

Hexagons Flexiframe® hexagon units are available either as equilateral hexagons where all six sides are equal or as a hexagon with non-equal sides. Equilateral hexagons are specified by iden-tifying the length of one side. Hexagons have a top parallel to and centered over the base. They are specified by identifying their height, top leg, base, and vertical leg lengths. Their total area may not exceed 50 square feet glass dimension (High-Performance™ Low-E4® tempered impact-resistant glass), and sides may be any dimension between 9" and 42".

Octagons Flexiframe® octagon units are available only as equilateral units. All angles and sides must be equal. They may be specified by identifying the length of one of their sides. Their total area may not exceed 50 square feet glass dimension, and sides may be any dimension between 9" and 36".

NOTE: Standard octagons are available in 2,' 2'-4" and 3' unit dimension sizes. See the Enhancement Windows size table for information on these sizes.

Pentagons Flexiframe® pentagon units are the most complex of the possible, available shapes. They are available as either angled or peaked pentagons. Angled pentagons are distinguished by their angle cut, or the “cut-off corner”, sloping left or right. Angled pentagons are specified by identifying the minimum width (top), maximum width (sill), minimum height (short side), and their maximum height (long side). Flexiframe® angled pentagons may not have an angle less than 14,° a leg less than 9," or an area (the product of its sill width multiplied by the height) greater than 50 square feet glass dimension. Peaked pentagons have a sill, two sides of equal length extending at right angles from the sill, and two sloped sides of equal length coming to a peak midway above the sill. Peaked pentagons are specified by identifying the width (sill), the height of one side, and the height from the sill to the peak. Flexiframe peaked pentagon units may not have an angle less than 14,° a leg less than 9," or an area (the product of its sill width multiplied by the height) greater than 50 square feet glass dimension.

Minimum and Maximum Limits for Flexiframe® UnitsFlexiframe® windows may be assembled in almost any shape, or in any size, with these minimum and maximum limits:

• May not have any angle less than 14.°

• May not exceed a maximum glass area greater than 50 square feet glass dimension for High-Performance™ Low-E4® tempered impact-resistant glass.

• May not exceed a maximum glass area greater than 30 square feet glass dimension for monolithic impact-resistant glass.

• Square footage is based on a square or rectangular glass shape.

• No leg may be less than 9" (6" glass dimension).

• Maximum width on short leg may not exceed 84" glass dimension.

• One leg must be less than 72" glass dimension.

• No dimension can exceed 120" glass dimension.

TrianglesTriangular Flexiframe® units are available in either isosceles or right triangle configurations. Isosceles triangles have two sides of equal length and equal slope. They should be specified by the width of their sill and their height from sill to peak. Right triangles have a 90° angle and may be defined by the length of the two legs extending from the 90° corner. Flexiframe triangles may not have an angle less than 14,° a leg less than 9," or an area (the product of its sill width multiplied by the height) greater than 50 square feet glass dimension.

TrapezoidsFlexiframe® trapezoid units are available with an angle face cut sloped to the left, or an angle face cut sloped to the right. They are specified by identifying their width (sill), selecting the minimum height (short side), and selecting the maximum height (long side). They are often specified so the angled top matches the slope of the roof. Flexiframe trapezoid units may not have an angle less than 14,° a leg less than 9," or an area (the product of its sill width multiplied by the height) greater than 50 square feet glass dimension (High-Performance™ Low-E4® tempered impact-resistant glass).

Parallelograms/DiamondsFlexiframe® horizontal and vertical parallelogram units are specified by identifying the length of two vertical legs and unit dimension width, along with pitch. Flexiframe diamond shape units are specified by identifying unit dimension width and unit dimension height (all four sides will be equal length). Flexiframe parallelogram and diamond shape units may not have an angle less than 14,° a leg less than 9," or an area greater than 50 square feet glass dimension.

isoscelestriangle rightangle

parallelogram diamond

peakpentagon

400

S

pecia

ltyW

indo

ws

Specialty Windows

40

Available for all sizes on this page.

Colonial Grille Pattern

* These units are shown with the Sunburst grille pattern. All other sizes (except where noted) are shown with the Renaissance grille pattern. Colonial grille pattern available for all sizes on this page.

Finelight ™ only available in 3/4" width.

2'-0 1/8"

2'-0 5/8"

19 3/8"

2'-4 3/8"

2'-4 7/8"

23 5/8"

2'-11 15/16"

3'-0 1/2"

31 3/16"

4'-0"

4'-0 1/2"

43 1/4"

4'-8 1/2"

4'-9"

51 3/4"

4'-11 1/4"

4'-11 3/4"

54 1/2"

5'-11 1/4"

5'-11 3/4"

66 1/2"

7'-11 1/8"

7'-11 5/8"

90 3/8"

8' 6' 5' 5' 4' 3' 2' 2'

12 5/8" 9 7/16" 7 13/16" 7 1/16" 6 7/16" 4 13/16" 4 21/32" 3 1/4"

12"

6"

2'-0

1/ 8

" 2'

-11

15/ 1

6"

3'-4

13/ 1

6"

4'-0

" 4'

-4 13

/ 16"

See

note

s ab

ove

for d

eter

min

ing

unit

and

roug

h op

enin

g he

ight

s

SH

OU

LD

ER

HE

IGH

T

(600) (2296)(492) (1314)(1099)(792) (1689)(1384)

(613)

(625)

(721)

(733)

(913)

(927)

(1219)

(1232)

(1435)

(1448)

(1505)

(1518)

(1810)

(1822)

(2416)

(2429)

(152

)(3

05)

(913

)(1

219)

(103

7)(6

13)

(134

1)

(122)(118)(83) (240)(198)(179)(164) (321)

(2438) (1829) (1524) (1524) (1219) (914) (610) (610)

AFCP3045AFCW145 AFFW8045(H.P.I.R. only)

AFFW6045AFFW5045AFCW245AFC245AFC145

AFC12 AFC22 AFCW22 AFFW502 AFFW602 AFFW802AFCW12 AFCP302

AFC13 AFC23 AFCW23 AFFW503 AFFW603 AFFW803AFCW13 AFCP303





AFFW8006*AFFW6006*AFFW5006*AFCW206*AFC206*AFCP3006*AFCW106*AFC106*

AFC11* AFC21* AFCW21* AFFW501* AFFW601* AFFW801*AFCW11* AFCP301*

Determining Arch Window Height DimensionsUnit Height: add the shoulder height to the chord height (see below for these dimensions).

Rough Opening Height: add 1/2" (13mm) to the unit height, or refer to the Arch Window Rough Opening Height chart.

Unobstructed Glass Height: subtract 4-3/4" (121mm) from the unit height.

CHORDHEIGHT

+

SHOULDERHEIGHT

ROUGHOPENINGHEIGHT

UNOBSTRUCTEDGLASS HEIGHT

• Dimensions in parentheses are in millimeters.• When ordering, be sure to specify color desired: White, Sandtone, Terratone® or Forest Green.• Combinations of window units joined together may require horizontal or vertical reinforcement.

This reinforcement should be speci�ed by a professional engineer. Contact your Andersen supplier for more information.

NOTE: Grille patterns for units with shoulder heights of 12" or less do not include horizontal dividers.• Rough opening dimensions may need to be increased to allow for use of building wraps, �ashing, sill panning,

brackets, fasteners or other items. See page 7 for more details.• “Unit Dimension” always refers to outside frame to frame dimension.• Arch window units are stationary.

UnobstructedGlass

MinimumRough Opg.

UnitDimension

CHORD HEIGHT

Radius

Frenchwood® patio door compatibleFor other grille pro�les see page 2-3.

Casement / Awning compatibleFor other grille pro�les see page 2-3.

7/8" (22)

1/2" (13) 1/2" (13)

3/4" (19)

Standard grille pattern for units above Standard grille pattern for units above

Table of Basic Sizes—Arch Window with Renaissance, Sunburst and Colonial Grille Scale 1/8" = 1'-0" (1:96)Custom Sizes Also Available

41

8'-0

1/ 8

" 5'

-11

7 /8"

5'

-4 1

3 /16

" 4'

-11

7 /8"

2'-0 1/8"

2'-0 5/8"

19 3/8"

2'-4 3/8"

2'-4 7/8"

23 5/8"

2'-11 15/16"

3'-0 1/2"

31 3/16"

4'-0"

4'-0 1/2"

43 1/4"

4'-8 1/2"

4'-9"

51 3/4"

4'-11 1/4"

4'-11 3/4"

54 1/2"

5'-11 1/4"

5'-11 3/4"

66 1/2"

7'-11 1/8"

7'-11 5/8"

90 3/8"

8' 6' 5' 5' 4' 3' 2' 2'

12 5/8" 9 7/16" 7 13/16" 7 1/16" 6 7/16" 4 13/16" 4 21/32" 3 1/4"

SH

OU

LD

ER

HE

IGH

T

(2296)(1314)(1099)(792) (1689)(1384)

(613)

(625)

(721)

(733)

(913)

(927)

(1219)

(1232)

(1435)

(1448)

(1505)

(1518)

(1810)

(1822)

(2416)

(2429)

(122)(118)(83) (240)(198)(179)(164) (321)

(600)(492)

(2438) (1829) (1524) (1524) (1219) (914) (610) (610)

(164

6)(1

521)

(182

6)(2

442)


AFFW605(H.P.I.R. only)

AFFW505AFCW25AFC25AFC15

AFC155 AFC255 AFCW255 AFFW5055(H.P.I.R. only)


AFCW155 AFCP3055

AFC16 AFC26 AFCW26 AFFW506(H.P.I.R. only)


AFCW16 AFCP306

AFC18 AFC28(H.P.I.R. only)

AFCW28(H.P.I.R. only)



AFCW18 AFCP308

See

note

s ab

ove

for d

eter

min

ing

unit

and

roug

h op

enin

g he

ight

s



Sizes on this page are shown with the Renaissance grille pattern. Colonial grille pattern also available for all sizes.

Finelight ™ only available in 3/4" width.

Determining Arch Window Height DimensionsUnit Height: add the shoulder height to the chord height (see below for these dimensions).

Rough Opening Height: add 1/2" (13mm) to the unit height, or refer to the Arch Window Rough Opening Height chart.


CHORDHEIGHT

+

SHOULDERHEIGHT

ROUGHOPENINGHEIGHT


• Dimensions in parentheses are in millimeters.• When ordering, be sure to specify color desired: White, Sandtone, Terratone® or Forest Green.• Combinations of window units joined together may require horizontal or vertical reinforcement.

This reinforcement should be speci�ed by a professional engineer. Contact your Andersen supplier for more information.

NOTE: Grille patterns for units with shoulder heights of 12" or less do not include horizontal dividers.• Rough opening dimensions may need to be increased to allow for use of building wraps, �ashing, sill panning,

brackets, fasteners or other items. See page 7 for more details.• “Unit Dimension” always refers to outside frame to frame dimension.• Arch window units are stationary.

UnobstructedGlass

MinimumRough Opg.

UnitDimension

CHORD HEIGHT

Radius

Frenchwood® patio door compatibleFor other grille pro�les see page 2-3.

Casement / Awning compatibleFor other grille pro�les see page 2-3.

7/8" (22)

1/2" (13) 1/2" (13)

3/4" (19)

Standard grille pattern for units above Standard grille pattern for units above

Grille alignment with other Andersen® products.All vertical arch window grille members were designed to be equally spaced. Vertical alignment may not coincide when units are transom joined. All horizontal grille members were designed to line up with corresponding casement sizes. See your Andersen retailer for alignment options. Special order arch window grilles are available to achieve proper alignment.

Table of Basic Sizes—Arch Window with Renaissance and Colonial Grille Scale 1/8" = 1'-0" (1:96)Custom Sizes Also Available

400

S

pecia

ltyW

indo

ws

Specialty Windows

42

36" (914)

6'-0"

6'-0

67 1/4"

5'-8 1/2"

5'-9"

63 3/4"

5'-4 1/2"

5'-5"

3'-1 1/2"

3'-2"

32 3/4"

1/2"

59 3/4"

12"

6"

2'-1

1 15

/ 16"

3'

-4 1

3 /16

" 4'

-0"

2'-0

1/ 8

"

6'-0"

6'-0

67 1/4"

5'-8 1/2"

5'-9"

63 3/4"

5'-4 1/2"

5'-5"

3'-1 1/2"

3'-2"

32 3/4"

1/2"

59 3/4"

4'-4

13 /

16"

5'-1

1 7 /

8 "

5'-4

13 /

16"

4'-1

1 7 /

8"

18 3/4" (476) 32 1/4" (819) 34 1/4" (870) 18 3/4" (476) 32 1/4" (819) 34 1/4" (870) 36" (914)

183/4" (476) 32 1/4" (819) 34 1/4" (870) 183/4" (476) 32 1/4" (819) 34 1/4" (870) 3' ( 914)

See

note

s ab

ove

for d

eter

min

ing

unit

and

roug

h op

enin

g he

ight

s

SH

OU

LD

ER

HE

IGH

T

(1829)

(1842)

(1708)

(1740)

(1753)

(1619)

(1638)

(1651)

(1518)

(953)

(965)

(832)

(152

)(3

05)

(913

)(1

219)

(103

7)(6

13)

(1829)

(1842)

(1708)

(1740)

(1753)

(1619)

(1638)

(1651)

(1518)

(953)

(965)

(832)

(134

1)(1

646)

(152

1)(1

826)

3' (914)

SE316 SE546(H.P.I.R. only)


SE3145


SE5445(H.P.I.R. only)

SE3135














SE313

SE312


SE542

SE3106

SE311 SE541

SE5406 SE6006

SE601

SE602



SE582

SE581

SE5806




Table of Basic Sizes—Springline™ Window with Renaissance and Colonial Grille Scale 1/8" = 1'-0" (1:96)Custom Sizes Also Available

Determining Springline™ Window Height DimensionsUnit Height: add the shoulder height to the chord height (see below for these dimensions).

Rough Opening Height: add 1/2" (13mm) to the unit height, or refer to the Springline Window Rough Opening Height chart.


ROUGHOPENINGHEIGHT

NOTE: Springline™ extension jambs are factory-applied when ordered with the unit.• Rough opening dimensions may need to be increased to allow for use of building wraps, �ashing, sill panning,

brackets, fasteners or other items. See page 7 for more details.• “Unit Dimension” always refers to outside frame to frame dimension.• Combinations of window units joined together may require horizontal or vertical reinforcement. This reinforcement

should be speci�ed by a professional engineer. Contact your Andersen supplier for more information.• When ordering, be sure to specify color desired: White, Sandtone, Terratone® or Forest Green.• Dimensions in parentheses are in millimeters.• Springline window units are stationary.

CHORDHEIGHT

+

SHOULDERHEIGHT


CHORDHEIGHT

UnitDimension

MinimumRough Opg.

UnobstructedGlass

Radius

43

Table of Basic Sizes—Springline™ Window with Renaissance and Colonial Grille Scale 1/8" = 1'-0" (1:96)Custom Sizes Also Available

Determining Springline™ Window Height DimensionsUnit Height: add the shoulder height to the chord height (see below for these dimensions).

Rough Opening Height: add 1/2" (13mm) to the unit height, or refer to the Springline Window Rough Opening Height chart.


ROUGHOPENINGHEIGHT

NOTE: Springline™ extension jambs are factory-applied when ordered with the unit.• Rough opening dimensions may need to be increased to allow for use of building wraps, �ashing, sill panning,

brackets, fasteners or other items. See page 7 for more details.• “Unit Dimension” always refers to outside frame to frame dimension.• Combinations of window units joined together may require horizontal or vertical reinforcement. This reinforcement

should be speci�ed by a professional engineer. Contact your Andersen supplier for more information.• When ordering, be sure to specify color desired: White, Sandtone, Terratone® or Forest Green.• Dimensions in parentheses are in millimeters.• Springline window units are stationary.

CHORDHEIGHT

+

SHOULDERHEIGHT


12"

6"

4'-0"

4'-0 1/2"

43 1/4"

5'-11 1/4"

5'-11 3/4"

66 1/2"

7'-11 1/8"

7'-11 5/8"

90 3/8"

48" (1219) 24" (610)

2'-0

1/ 8

" 2'

-11

15/ 1

6"

3'-4

13 /

16"

4'-0

"

4'-4

13 /

16"

5'-1

1 7 /

8"

5'-4

13/ 1

6"

4'-1

1 7 /

8"

8'-0"

8'-0 1/2"

91 1/4"

12"

6"

4'-0"

4'-0 1/2"

43 1/4"

24" (610)

2'-0

1/ 8

"

30 13/16" (783) 41 9/16" (1056)

4' 3' 4' 2' 2'

See

note

s ab

ove

for d

eter

min

ing

unit

and

roug

h op

enin

g he

ight

s

SH

OU

LD

ER

HE

IGH

T

SH

OU

LD

ER

HE

IGH

T

SH

OU

LD

ER

HE

IGH

T

(1219)

(1232)

(1099)

(1810)

(1822)

(1689)

(2416)

(2429)

(2296)

(152

)(3

05)

(913

)(1

219)

(103

7)(6

13)

(134

1)(1

646)

(152

1)(1

826)

(2438)

(2451)

(2318)

(152

)(3

05)

(613

)

(1219)

(1232)

(1099)

(1219) (914) (1219) (610) (610)

SP4055

SP4045

SP4035

SP402

SP403

SP404

SP405

SP406(H.P.I.R. only)




ELFW602

ELFW6006

ELFW601

ELFW802(H.P.I.R. only)



See

note

s ab

ove

for d

eter

min

ing

unit

and

roug

h op

enin

g he

ight

s

See

note

s ab

ove

for d

eter

min

ing

unit

and

roug

h op

enin

g he

ight

s

Available for all sizes on this and the previous page.



CHORDHEIGHT

UnitDimension

MinimumRough Opg.

UnobstructedGlass

Radius

CHORDHEIGHT

UnitDimension

MinimumRough Opg.

UnobstructedGlass

Radius

Grille alignment with other Andersen® products.All vertical Springline™ window grille members were designed to be equally spaced. Vertical alignment may not coincide when units are transom joined. All horizontal grille members were designed to line up with corresponding casement sizes. See your Andersen retailer for custom grille alignment options. Special order arch window grilles are available to achieve proper alignment.

400

S

pecia

ltyW

indo

ws

Specialty Windows

44

Table of Basic Sizes—Enhancement Windows Scale 1/8" = 1'-0" (1:96)

• Rough opening dimensions may need to be increased to allow for use

of building wraps, ashing, sill panning, brackets, fasteners or other

items. See page 7 for more details.


• Combinations of window units joined together may require horizontal

or vertical reinforcement. This reinforcement should be speci�ed

by a professional engineer. Contact your Andersen supplier for

more information.

• When ordering, be sure to specify color desired: White, Sandtone,

Terratone® or Forest Green.


• Enhancement window units are stationary.

• Contact your Andersen supplier for Gothic grille pattern availability.

AG: Andersen® art glass panels are available for these sizes by special

order only. Contact your Andersen supplier.

2'-9 5/8"

2'-10 1/8"

24 7/8"

3'-1 5/8"

3'-2 1/8"

3'-5 5/8" 3'-9 5/8"

3'-6 1/8" 3'-10 1/8"

32 7/16" 32 5/16"

10 7

/ 16"

11"

9 1 /

8"

1-0

1 /16

"

9 5 /

8"

1-0

5 /8"

9 7 /

16"

10"

2'-11 15/16"

3'-0 1/2"

28 15/16"

4'-0"

4'-0 1/2"

4'-8 1/2"

4'-9"

47 7/8"

4'-11 1/4"

4'-11 3/4"

49 7/16"

5'-11 1/4"

5'-11 3/4"

1-1

3 /8"

1-1

7 /8"

10 11

/ 16"

11 1 /

4"

6"

1-1

11/ 1

6"

1-2

1 /4"

9"

1-3

9 /16

"

1-4

1 /8"

1-3

13/ 1

6"

1-4

3 /8"

11 1

/ 8"

5 3 /

4"

4 3 /

8"

26 1/8"

7 5 /

16"

4 3 /

4"

35 7/8"

8 11

/ 16"

10 13

/ 16"

59 11/16"

18 3/4" (476) 24" (610) 24" (610) 32 1/4" (819)

18 3/4" (476) 32 1/4" (819) 36" (914)

36" (914) 48" (1219)

(395

)

(410

)

(275

)

(854)

(867)

(632)

(956)

(968)

(664)

(1057) (1159)

(1070) (1172)

(824) (821)

(265

)

(279

)

(146

)

(232

)

(244

)

(111

)

(306

)

(321

)

(186

)

(240

)

(254

)

(121

)

(913)

(927)

(735)

(1219)

(1232)

(911)

(1435)

(1448)

(1216)

(1504)

(1518)

(1256)

(1810)

(1822)

(1516)

(340

)

(352

)

(221

)

(271

)

(286

)

(152

)

(348

)

(362

)

(274

)

(402

)

(416

)

(283

)

FCD28 AG

DOUBLE-HUNG sizesColonial Pattern

CASEMENT sizesColonial Pattern

FCD30 AG

FCD34 AG

FCD38 AG

FCCXW3 AG

FCC2 AG

FCCW2 AG

FCFW60 AG

FCFW50 AG

example

example

example

Full Chord

FRENCHWOOD® DOOR sizesColonial Pattern

UnitDimension

MinimumRough Opg.

UnobstructedGlass

Radius

UnitDimension

MinimumRough Opg.

UnobstructedGlass

Radius

UnitDimension

MinimumRough Opg.

UnobstructedGlass

Radius

Custom Pattern Examples

Custom grille patterns are also available. For more information on Andersen™ divided light, see page 2-3 or visit andersenwindows.com/grilles.

2'-0 1/8"

2'-0 5/8"

19 7/16"

2'-4 3/8"

2'-4 7/8"

23 11/16"

2'-11 15/16"

3'-0 1/2"

31 1/4"

4'-0"

4'-0 1/2"

3'-6

"

3'-6

1/ 2

"

36 9

/ 16"

4'-0

"

4'-0

1/ 2

"

4'-6

"

4'-6

1/ 2

"

5'-6

"

5'-6

1/ 2

"

4'-0"

4'-0 1/2"

43 5/16"

4'-0"

4'-0 1/2"

43 1/4"

6'-0"

6'-0 1/2"

67 5/16"

2'-0"

2'-0 1/2"

2'-4"

2'-4 1/2"

3'-0"

3'-0 1/2"

19 5/16" 23 5/16" 31 5/16"

43 5/16"

60 7

/ 8"

48 7

/ 8"

42 3

/ 4"

Radius

ShoulderHeight

Radius

ShoulderHeight

Radius

ShoulderHeight Shoulder

Height

32 1/4"(819) 16 27/32"(428)

32 1/4" (819)

21 9/32" (541)

36"(914)

22 27/32" (580)

Radius

48"(1219)

24 7/16" (621)

Radius

36"

Radius24"

Radius

48"

(613)

(625)

(494)

(721)

(733)

(602)

(913)

(927)

(794)

(1219)

(1232)

(1100)

(106

7)

(108

0)

(929

)

(121

9)

(123

2)

(108

6)

(137

2)

(138

4)

(124

1)

(167

6)

(168

9)

(154

6)

(1219)

(1232)

(1100)

(1219)

(1232)

(1099)

(1829)

(1842)

(1710)

(610)

(622)

(491)

(711)

(724)

(592)

(914)

(927)

(795)

(914) (610)

(1219)

QR40 AG

FR40 AG

FR60

OC20 AG OC24

AG OC30 AG

GT2036 AG GT3046

AG

GT2440 AG

GT4056

Gothic

Monumental Quarter Round / Full Round Standard Octagon

Colonial Pattern

Renaissance Pattern

UnitDimension

MinimumRough Opg.

UnobstructedGlass

UnitDimension

MinimumRough Opg.

UnobstructedGlass

UnitDimension

MinimumRough Opg.

UnobstructedGlass

45

Springline™ Flanker (custom arch) Window Sizes Scale 1/8" = 1'-0" (1:96)

NOTE: To order these custom arch - Springline™ �anker units, contact your Andersen supplier.AG: Andersen® art glass panels are available for these sizes by special order only. Contact your Andersen supplier.• Rough opening dimensions may need to be increased to allow for use of building wraps, �ashing, sill panning, brackets, fasteners or other items. See page 7 for more details.• “Unit Dimension” always refers to outside frame to frame dimension.• Combinations of window units joined together may require horizontal or vertical reinforcement. This reinforcement should be speci�ed by a professional engineer. Contact your Andersen supplier for more information.• When ordering, be sure to specify color desired: White, Sandtone, Terratone® or Forest Green.• Dimensions in parentheses are in millimeters.• Enhancement window units are stationary.

36" (914)18 3/4" (476) 24" (610) 32 1/4" (819)

1'-5"

12 3/4"

(432)

(445)

(324)

1'-51/2" 1'-51/2"

1'-5"

12 3/4"

(432)

(445)

15 3/4"

(521)

(533)

(400)

1'-9"

15 3/4"

(521)

(533)

(400)

1'-9"

1'-81/2" 1'-81/2"

19 3/8"

(613)

(625)

(492)19 3/8"

(613)

(625)

(492)

2'-01/8" 2'-01/8"

2'-05/8" 2'-05/8"

23 5/8" 23 5/8"

(721)

(733)

(600)

(721)

(733)

(600)

2'-43/8" 2'-43/8"

2'-47/8" 2'-47/8"

31 3/16"

(913)

(927)

(792)

(913)

(927)

(792)

2'-1115/16" 2'-1115/16"

3'-0 1/2" 3'-0 1/2"

31 3/16"

(913

)

(927

)

(792

)

2'-1

115 /

16"

3'-0

1/ 2

"

31 3

/ 16"

(103

7)

(105

1)

(986

)

3'-4

13 /

16"

3'-5

3 /8"

38 1

3 /16

"

4'-0

"

43 1

/ 4"

(121

9)

(123

2)

(109

9)

4'-0

1/ 2

"

55 1

/ 8"

(152

1)

(153

4)

(140

0)

4'-1

1 7 /

8"

5'-0

3/ 8

"

67 1

/ 4"

(182

6)

(183

8)

(170

8)

5'-1

1 7 /

8"

6'-0

3/ 8

"

C R width

32 1/4" (819)

Radius

Shoulder Height

17 5/16"(440)

183/4"(476)

Radius

Shoulder Height

24" (610)

121/4" (311)

Radius

Shoulder Height

Radius

Shoulder Height

Radius

Shoulder Height

Radius

Shoulder Height

Radius

Shoulder Height

Radius

Shoulder Height

Radius

Shoulder Height

Radius

Shoulder Height

Radius

Shoulder Height

Radius

Shoulder Height

Radius

Shoulder Height

Radius

Shoulder Height

Radius

Shoulder Height

Radius

Shoulder Height

Radius

Shoulder Height

Radius

Shoulder Height

Radius

Shoulder Height

Radius

Shoulder Height

Radius

Shoulder Height

22 3/16"(564)

24" (610)

17 1/8"(435) 9 5/8" (244)

32 1/4" (819)

813/16"(234)

321/4"(819)

29 3/8" (721)

24" (610)

24 5/16" (618) 1613/16" (427)

321/4" (819) 32 1/4"(819)

16" (406)

36" (914)

12" (305)

411/4"(1048)

24" (610)

36 3/16"(919) 2811/16"(729)

321/4" (819) 32 1/4" (819)

27 7/8" (708)

36" (914)

23 7/8"(606)

53 1/4"(1353)

24" (610)

48 3/16"(1224) 4011/16"(1033)

321/4" (819) 321/4" (819)

39 7/8"(1013)

36" (914)

35 7/8"(911)

(324)

C N width

C3 h

eigh

tC3

5 he

ight

C4 h

eigh

tC5

hei

ght

C6 h

eigh

t

C width C W width C X W widthCasement Size

183/4"(476)

18 3/4"(476)

18 3/4"(476)

18 3/4" (476)

AG AG

AG AG AG AG

AG AG AG AG AG

AG AG AG AG AG

AG AG AG AG AG

Standard Renaissance interior grille pattern shown. For other grille options, contact your Andersen supplier.

UnitDimension

MinimumRough Opg.

UnobstructedGlass

Radius

Custom Arch Windows Design Criteria

Design Considerations

There are nine standard radii to choose from: 18-3/4", 2', 32-1/4", 34-1/4", 3', 4', 5', 6', and 8'.

Maximum single unit width is based on available radius piece length. Contact supplier for speci�c information.– Equal leg arch maximum unit width range: 36-3/4" for 18-3/4" radius. (See next page.)– Unequal leg arch maximum unit width range: 18-3/4" for 18-3/4" radius.– Partial chord maximum unit width range: 18-3/4" for 18-3/4" radius.

All units are stationary.

May not exceed a maximum glass area greater than 50 square feet glass dimension forHigh-Performance™ Low-E4® tempered impact-resistant glass.

May not exceed a maximum glass area greater than 30 square feet glass dimension for monolithic impact-resistant glass.

Square footage is based on square or rectangular glass shape.

Only one unit dimension (height or width) can exceed 7' 0."

No leg of any unit can be less than 9."Do all calculations in inches to three decimal places.

Order extension jambs with units to assure correct sizing.

There are certain factors that must be considered when deciding on a custom arch size or shape. Below we have listed some of those factors. But for speci�c design criteria, mullion joining guidelines and order information, contact your Andersen supplier.

Andersen offers even greater design �exibility with

custom-dimensioned equal leg arches, unequal leg arches

and partial chords. Custom arch windows can be designed

using one of nine standard radii, further expanding the

existing line of 90 standard sizes of Andersen® arch windows.

Color coordinate with any project. New arches are available

in White, Sandtone, Terratone® or Forest Green. Andersen™

divided light is available for most styles and sizes. Contact

your supplier for availability.

Custom arch shapes and sizes are specially constructed

to be used in combination with other Andersen windows

including: casement and awning windows, double-hung

windows, gliding windows, hinged or gliding patio doors

and Flexiframe® windows.

400

S

pecia

ltyW

indo

ws

46

Specialty Windows

12345

18-3/4"R (3'0-3/4")

2'R (3'11-1/4")

3'R (5'11-1/4)

4'R (7'11-1/4")

5'R (5'0")

6'R (6'0-5/8")

8'R (8'0-1/8")

32-1/4"R (5'3-3/4")

18-3/4"R

32-1/4"R

34-1/4"R

2'R

3'R

4'R

5'R

6'R

8'R

1 2 3 4 5FEET

34-1/4"R (5'7-3/4")

Custom Arch Windows

equal leg arch unequal leg arch partial chord

Standard radii for custom arch

Maximum width for equal leg arch.

Expanded arch capabilities to achieve

Springline™ window expression.

Custom arch windows allow for increased design �exibility. The illustration to the right uses equal leg arch examples to indicate that both the width and height of custom arch windws can be varied (increments of 1/32") for all three shapes (shown above) while utilizing the nine standard radii.

Unit Number

GlassSq. Ft. (m2)

AFC106 0.70 (0.065)AFC11 1.60 (0.149)AFC12 3.40 (0.316)AFC13 5.10 (0.474)AFC135 5.80 (0.539)AFC14 6.80 (0.632)AFC145 7.50 (0.697)AFC15 8.50 (0.790)AFC155 9.20 (0.855)AFC16 10.30 (0.957)AFC18 13.80 (1.282)AFCW106 1.10 (0.102)AFCW11 2.10 (0.195)AFCW12 4.20 (0.390)AFCW13 6.30 (0.585)AFCW135 7.10 (0.660)AFCW14 8.40 (0.780)AFCW145 9.20 (0.855)AFCW15 10.40 (0.966)

Unit Number

GlassSq. Ft. (m2)

AFCW155 11.30 (1.050)AFCW16 12.50 (1.161)AFCW18 16.80 (1.561)AFCP3006 1.40 (0.130)AFCP301 2.80 (0.260)AFCP302 5.50 (0.511)AFCP303 8.20 (0.762)AFCP3035 9.30 (0.864)AFCP304 10.90 (1.013)AFCP3045 12.00 (1.115)AFCP305 13.60 (1.263)AFCP3055 14.70 (1.366)AFCP306 16.30 (1.514)AFCP308 21.80 (2.025)AFC206 2.20 (0.204)AFC21 4.10 (0.381)AFC22 7.80 (0.725)AFC23 11.50 (1.068)AFC235 13.00 (1.208)

Unit Number

GlassSq. Ft. (m2)

AFC24 15.20 (1.412)AFC245 16.70 (1.551)AFC25 18.90 (1.756)AFC255 20.40 (1.895)AFC26 22.60 (2.100)AFC28 30.20 (2.806)AFCW206 2.80 (0.260)AFCW21 5.10 (0.474)AFCW22 9.50 (0.883)AFCW23 13.90 (1.291)AFCW235 15.70 (1.459)AFCW24 18.30 (1.700)AFCW245 20.10 (1.867)AFCW25 22.70 (2.109)AFCW255 24.60 (2.285)AFCW26 27.20 (2.527)AFCW28 36.10 (3.354)AFFW5006 3.20 (0.297)AFFW501 5.50 (0.511)

Unit Number

GlassSq. Ft. (m2)

AFFW502 10.30 (0.957)AFFW503 14.80 (1.375)AFFW5035 16.70 (1.551)AFFW504 19.50 (1.812)AFFW5045 21.40 (1.988)AFFW505 24.10 (2.239)AFFW5055 26.10 (2.425)AFFW506 28.80 (2.676)AFFW508 38.20 (3.549)AFFW6006 4.40 (0.409)AFFW601 7.20 (0.669)AFFW602 12.90 (1.198)AFFW603 18.50 (1.719)AFFW6035 20.80 (1.932)AFFW604 24.20 (2.248)AFFW6045 26.50 (2.462)AFFW605 29.80 (2.769)AFFW6055 32.10 (2.982)AFFW606 35.50 (3.298)

Unit Number

GlassSq. Ft. (m2)

AFFW608 46.90 (4.357)AFFW8006 7.30 (0.678)AFFW801 11.10 (1.031)AFFW802 18.80 (1.747)AFFW803 26.40 (2.453)AFFW8035 29.50 (2.741)AFFW804 34.10 (3.168)AFFW8045 37.10 (3.447)AFFW805 41.60 (3.865)SE3106 3.74 (0.347)SE311 5.10 (0.474)SE312 7.86 (0.730)SE313 10.54 (0.979)SE3135 11.65 (1.082)SE314 13.28 (1.234)SE3145 14.38 (1.336)SE315 15.98 (1.485)SE3155 17.10 (1.589)SE316 18.71 (1.738)

Unit Number

GlassSq. Ft. (m2)

SE5406 11.22 (1.042)SE541 13.71 (1.274)SE542 18.74 (1.741)SE543 23.64 (2.196)SE5435 25.66 (2.384)SE544 28.64 (2.661)SE5445 30.64 (2.847)SE545 33.57 (3.119)SE5455 35.61 (3.308)SE546 38.54 (3.580)SE5806 12.67 (1.177)SE581 15.33 (1.424)SE582 20.69 (1.922)SE583 25.92 (2.408)SE5835 28.08 (2.609)

Unit Number

GlassSq. Ft. (m2)

SE584 31.26 (2.904)SE5845 33.39 (3.102)SE585 36.51 (3.392)SE5855 38.70 (3.595)SE586 41.82 (3.885)SE6006 14.01 (1.302)SE601 16.81 (1.562)SE602 22.47 (2.088)SE603 27.98 (2.599)SE6035 30.26 (2.811)SE604 33.61 (3.122)SE6045 35.86 (3.332)SE605 39.16 (3.638)SE6055 41.46 (3.852)SP402 11.62 (1.080)

Unit Number

GlassSq. Ft. (m2)

SP403 15.16 (1.408)SP4035 16.63 (1.545)SP404 18.78 (1.745)SP4045 20.23 (1.879)SP405 22.35 (2.076)SP4055 23.83 (2.214)SP406 25.95 (2.411)SP8006 24.98 (2.321)SP801 24.98 (2.321)SP802 36.46 (3.387)ELFW6006 11.58 (1.076)ELFW601 14.35 (1.333)ELFW602 19.95 (1.853)ELFW8006 20.88 (1.940)ELFW801 24.64 (2.289)ELFW802 32.25 (2.996)

Unit Number

GlassSq. Ft. (m2)

FCD28 0.688 (0.064)FCD30 0.540 (0.050)FCD34 1.145 (0.106)FCD38 0.837 (0.078)FCCXW3 1.241 (0.115)FCC2 1.017 (0.094)FCCW2 2.781 (0.258)FCFW50 2.571 (0.239)FCFW60 3.154 (0.293)

Unit Number

GlassSq. Ft. (m2)

GT2036 4.008 (0.372)GT2440 5.841 (0.543)GT3046 8.783 (0.816)GT4056 14.877 (1.382)

QR40 9.905 (0.920)FR40 10.217 (0.949)FR60 24.690 (2.294)

OC20 2.138 (0.199)OC24 3.118 (0.290)OC30 5.629 (0.523)

Arch Window Glass Area

Springline™ Window Glass Area Enhancement Window Glass Area

Frenchwood®

Gliding Patio Doors

Combining the beauty of traditional French door styling with space-saving

design, Frenchwood® gliding patio doors ride smoothly and easily on

corrosion-resistant stainless steel and precision ball bearing rollers.

Section Reference




Joining Details ..................... 52


Sidelights & Transoms ......... 68


Performance Data ............... 75 400

F

renc

hwoo

d®

Glid

ing

Patio

Doo

rs

48

Features


Frenchwood® Gliding Patio Doors

Exterior Interior

brightbrass

antiquebrass

polishedchrome

brushedchrome

satinnickel

oilrubbedbronze

distressednickel

distressedbronze


Hardware Finishes

White Sandtone Terratone® ForestGreen pine oak maple

FLEXIBLE SEAL

A patented full-length combination weatherstrip/ interlock system provides a flexible seal at the meeting stile.

REAcHout LockIng HARdwARE

The unique Andersen reachout locking system pulls the door panel snugly into the jamb for weathertightness and enhanced security.

MoRtISE-And- tEnon JoIntS

Panel joints are mortise- and-tenon with patented dowel construction for maximum strength.

All panels feature stainless steel 5-inch

screws to reinforce the joints.


white

FRAME

The sill of the Frenchwood® gliding

patio door with Stormwatch® protection is reinforced and has a raised sill design for increased water resistance. Additional height on the inside sill helps resist wind-driven water penetration. The extruded aluminum track has a stainless steel cap that resists stain, rust and denting. A thermal barrier reduces conductive heat loss and checks condensation on the inside. The sill has an attractive wear-resistant, heat-baked finish in a neutral gray color. Standard frame depth is 4-9/16''.

All basic exterior frame members are covered with a seamless rigid vinyl (PVC) sheath that maintains an attractive appearance while minimizing maintenance. Andersen® Frenchwood gliding patio doors are available in four neutral colors. Specify White, Sandtone, Terratone® or Forest Green color.

Wood frame members are treated with a water-repellent preservative for long-lasting* protection and performance.

Interior frame trim pieces are clear unfinished pine. Oak and maple veneer and prefinished white interior options are available.

For secure installa-tion, head brackets

are attached with five screws while the sill brackets have three screws through the sill into the sub floor.

A flexible PVC weatherstrip on the side jambs, and a pile weatherstrip on the head, provide a positive seal between the frame and panels.

PAnEL

The exterior of the wood door panel is protected with a long-lasting* urethane base finish in White, Sandtone, Terratone® or Forest Green color.

Panel interior surfaces are unfinished clear pine. Unfinished oak and maple veneers are available as options. Low-maintenance prefinished white interiors are also available on units with White exteriors.

Dual corrosion-resistant ball bearing rollers on door panels provide smooth gliding operation with self-contained leveling adjusters.

Dual ball bearing rollers have

deep grooves to increase engagement with the roll guide and resist lateral movement.

A panel stiffener along the full length of the

meeting stile supports the stationary panel when it is under structural pressure.

Operating panels have a full-length

stiffener bar on the edge of the meeting stile. The panel stiffener matches the interior wood species of the patio door for enhanced appearance.

A parting stop bracket adds strength to the

door by adding resistance to high wind pressures on the operating panel.




Naturally occurring variations in grain, color and texture make each wood door panel one-of-a-kind.

Specify a unit exterior color option and an interior finish/veneer option to complete your order. Prefinished white interiors are only available on units with white exteriors.

Encino®Whitmore®Covington™Newbury®Anvers®Tribeca®Albany® Yuma®

white

stone

gold dust

black

white

stone

bright brass

satin nickel

oil rubbed bronze

bright brass

antique brass

polished chrome

brushed chrome

satin nickel

oil rubbed bronze

bright brass

antique brass

oil rubbed bronze

bright brass

antique brass

satin nickel

oil rubbed bronze

distressed nickel

distressed bronze

distressed nickel

distressed bronze


49









* For complete information on our warranties, visit andersenwindows.com or contact your Andersen supplier.

NOTe: Andersen® patio doors are not intended for use as entrance doors.


"Delrin" is a registered trademark of e.I. duPont deNemours and Company.

Accessories Sold Separately.

HARdwARE

Exterior Keyed LockA six-pin exterior key cylinder lock is available for all patio doors in styles and finishes that coordinate with hardware. This lock allows the patio door to be locked and unlocked from the exterior.

InStALLAtIon AccESSoRIES

See page 6 for information on Andersen’s extensive array of installation accessories to help finish out your installation.

tRAnSoMS

Andersen® Frenchwood® patio door transoms feature elegant lines that match our 400 Series Frenchwood gliding patio doors. They feature pine, oak, maple or prefinished white interior options, plus our four standard exterior colors. Size information available on pages 68-69.

SIdELIgHtS

Stationary units can also be selected for use as sidelights. See size table on page 50 for size options.

Like the doors they complement, Andersen transoms and sidelights are available with Stormwatch® protection. Size information available on pages 68-69.

InSEct ScREEnS

Perma-Clean® Gliding Insect ScreenThe insect screen is available for both two-panel doors and four-panel doors (PG Upgrade). Choose among the following colors: White, Sandtone, Terratone® or Forest Green color baked-on enamel finish. Patented square corner joint construction adds considerable strength to the frame members, and the long-lasting* glass fiber screen cloth has a charcoal finish. Delrin® injection molded bottom rollers with self-contained leveling adjusters provide smooth operation. Interior and exterior pulls and latch are provided.

Perma-Clean® Retractable Insect ScreenThe retractable insect screen is installed on the exterior of the door and opens across the width of the opening. When the insect screen is not in use, it neatly retracts into a small canister mounted on the exterior of the door. The retractable insect screen canister is available for two-panel patio doors in White, Sandtone, Terratone® and Forest Green. Please note, retractable screen track reduces clear opening height by 1."

FRAME

Extension Jambs

Standard jamb depth is 4-9/16" (116). Clear pine, oak or maple veneer or white interior extension jambs are available for the following wall thicknesses:

• 5-1/4" (133) • 6-9/16" (167) • 7-1/8" (181)

ThresholdAn oak or maple threshold is available for finishing the interior of the sill on the Frenchwood® gliding patio doors.

Ramped Sill InsertProvides smooth transition from interior to exterior. Can be used with retractable insect screen, but cannot be used with gliding insect screen. (Specifier must check with local and federal officials to determine if product meets accessibility codes.)

Sill Support An aluminum sill support is designed to lock into a channel under the sill and tie back into the wall. This will offer support to the outermost sill section when needed. Available in neutral gray finish.

gLASS

Panels are silicone bed glazed and finished with an interior wood stop and an exterior silicone bead.

Interior wood stops are secured using 1-1/2"

16-gauge crown staples instead of nails. Silicone is also applied to the full perimeter of the glass on the interior side of the pane to add strength and stability.


• Standard High-Performance™ Low-e4® tempered glass(PG Upgrade)

• Standard High-Performance™ Low-e4® Sun tempered glass (PG Upgrade)

• Standard High-Performance™ Low-e4® SmartSun™ tempered glass (PG Upgrade)

• High-Performance™ Low-e4® tempered impact-resistant glass

• High-Performance™ Low-e4® Sun tempered impact-resistant glass

• High-Performance™ Low-e4® SmartSun™ tempered impact-resistant glass

• Monolithic impact- resistant glass


Pg uPgRAdES

Frenchwood® Gliding Patio DoorsPG Upgrades are available for select sizes only. Ask your Andersen supplier for details.

gRILLES

Divided Light PatternsSee page 67 for divided light patterns or visit andersenwindows.com/grilles.

gLASS

Andersen® Art GlassAndersen art glass panels are available for sidelights, transoms and stationary units. They come in eleven original patterns, including four Frank Lloyd Wright ® series designs. See the Andersen ® Product Guide for details on Andersen art glass, or visit andersenwindows.com/artglass for pattern information.


400

F

renc

hwoo

d®

Glid

ing

Patio

Doo

rs

Frenchwood® Gliding Patio Doors

50

Grille order number:FWG2668 FWG2680FWG26611



2'-8 3/4"

2'-8"

3'-2 3/4"

3'-2"

6'-0"

5'-11 1/4"

6'-0"

4'-2 3/4"

4'-2"

8'-0" 8'-0"

5'-0"

Unit Dimension


5'-0"

4'-11 1/4"

Unobstructed Glass

Unit Dimension


Unobstructed Glass

Unit Dimension


Unobstructed Glass

4'-11 1/4"

5'-11 1/4"

7'-11 1/4" 7'-11 1/4"

Availablein

3 heights

Availablein

3 heights

Availablein

3 heights

21 1/8" 21 1/8" 21 1/8" 21 1/8" 21 1/8"

27 1/8" 27 1/8" 27 1/8" 27 1/8" 27 1/8"

39 1/8" 39 1/8" 39 1/8" 39 1/8" 39 1/8"

(1810)

(1829)

(965)

(984)

(1505)

(1524)

(1505)

(1524)

(2419)

(2438)

(2419)

(2438)

(1270)

(1289)

(813)

(832)

(1810)

(1829)

(537) (537) (537)

(689) (689) (689) (689) (689)

(994)

(537) (537)

(994) (994) (994) (994)

1 FWG 2968S2 FWG 29611S3 FWG 2980S

1 FWG 3368S2 FWG 33611S3 FWG 3380S

1 FWG 4368S2 FWG 43611S3 FWG 4380S

1 FWG xx68 2 FWG xx611 3 FWG xx80

FWG 5068RFWG 50611RFWG 5080R

FWG 5068LFWG 50611LFWG 5080L





6'-1

1"

6'-1

0 3 /

8"

66"

(209

2)

(210

8)

(167

6)

6'-8

"

6'-7

1/ 2

"

63 1

/ 8"

(201

9)

(203

2)

(160

3)

8'-0

"

7'-1

1 1 /

2"

79 1

/ 8"

(242

6)

(243

8)

(201

0)

Table of Basic Unit Sizes Scale 1/8" = 1'-0" (1:96)Exterior views shown. Arrow indicates direction of panel.

• Rough opening dimensions may need to be increased to allow for use of building wraps, �ashing, sill panning, brackets, fasteners or other items. See page 7 for more information.



• Combinations of door units joined together may require horizontal or vertical reinforcement. This reinforcement should be speci�ed by a professional engineer.


• When ordering, be sure to specify product type: High-Performance™ Low-E4® impact-resistant, monolithic impact-resistant or PG Upgrade.

• For Miami-Dade County installations, please refer to Notice of Acceptance Report.

1/8" increments

1/ 8

" in

crem

ents

Custom sizes available in 1/8" increments between the smallest and largest standard patio door sizes. Some restrictions apply. Contact your Andersen supplier for availability.

Three Basic Unit Heights Custom Sizes

Divided Light Patterns for Patio DoorsIn addition to the Colonial grille patterns shown in the table of basic unit sizes, other standard divided light patterns are available. For examples, see page 67 or visit andersenwindows.com/grillesPrairie

pattern

51

Opening Specifications

Frenchwood® Gliding Patio Door 6' 8" Height

Unit Number

Sq. Ft. (m2) Clear

Opening

Max. Clear Opening In Full Open Position

in inches (and mm)Sq. Ft.

(m2) GlassSq. Ft.

(m2) Vent

Overall Unit Area

Sq. Ft. (m2)Width Height

2968

— — — 9.26 — 17.67— — — (0.860) — (1.642)

3368 — — — 11.89 — 20.98— — — (1.105) — (1.949)

4368 — — — 17.15 — 27.60— — — (1.593) — (2.564)

5068 11.58 22-1/8" 75-3/8" 18.52 11.58 32.71(1.076) ( 562) (1915) (1.721) (1.076) (3.039)

6068 14.72 28-1/8" 75-3/8" 23.78 14.72 39.34(1.368) (714) (1915) (2.209) (1.368) (3.655)

8068 21.00 40-1/8" 75-3/8" 34.3 21.00 52.59(1.951) (1019) (1915) (3.187) (1.951) (4.886)


Unit Number

Sq. Ft. (m2) Clear

Opening



(m2) GlassSq. Ft.

(m2) Vent

Overall Unit Area


29611

— — — 9.68 — 18.31— — — (0.899) — (1.701)

33611 — — — 12.43 — 21.74— — — (1.155) — (2.020)

43611 — — — 17.93 — 28.60— — — (1.666) — (2.657)

50611 12.04 22-1/8" 78-3/16" 19.36 12.04 33.89(1.119) ( 562) (1987) (1.799) (1.119) (3.148)

60611 15.31 28-1/8" 78-3/16" 24.86 15.31 40.76(1.422) ( 714) (1987) (2.310) (1.422) (3.787)

80611 21.84 40-1/8" 78-3/16" 35.85 21.84 54.49(2.029) (1019) (1987) (3.331) (2.029) (5.062)


Unit Number

Sq. Ft. (m2) Clear

Opening



(m2) GlassSq. Ft.

(m2) Vent

Overall Unit Area


2980

— — — 11.60 — 21.22— — — (1.078) — (1.971)

3380 — — — 14.90 — 25.20— — — (1.384) — (2.341)

4380 — — — 21.49 — 33.16— — — (1.996) — (3.081)

5080 14.04 22-1/8" 91-3/8" 23.20 14.04 39.29(1.304) (562) (2321) (2.155) (1.304) (3.650)

6080 17.85 28-1/8" 91-3/8" 29.80 17.85 47.25(1.658) (714) (2321) (2.769) (1.658) (4.390)

8080 25.46 40-1/8" 91-3/8" 42.98 25.46 63.17(2.365) (1019) (2321) (3.993) (2.365) (5.869)


• Rough opening dimensions may need to be increased to allow for use of building wraps,

�ashing, sill panning, brackets, fasteners or other items. See page 7 for more details.

* 4-9/16" measurement is from backside of �ange to inside edge of door frame.

Andersen®optional oak ormaple threshold

Optionalsill support

Head

Sill

5-13/16"(148)

10-9/16"(268)

Min

imum

Rou

gh O

peni

ng H

eigh

t

Unit

Dim

ensi

on H

eigh

t

Insectscreen

Clea

r Ope

ning

Hei

ght

Jamb Jamb

Minimum Rough Opening Width3/8" (10)

3/8" (10)

Active Panel Stationary Panel

4-9/16" (116)Jamb Width*

1-5/16" (33)

5-7/16" (138)

5-3/8" (137)3-1/8"(79)

3-1/8"(79)

Clear OpeningWidth


Meeting Stile

Vertical SectionHigh-Performance™ Low-E4® Impact-Resistant Glass


400

F

renc

hwoo

d®

Glid

ing

Patio

Doo

rs

52

Frenchwood® Gliding Patio DoorsM

inim

um R

ough

Ope

ning

Hei

ght

Unit

Dim

ensi

on H

eigh

t

1-5/16" (33)

1" (25)13/16" (21)

4" (102)

5-13/16"(148)

10-9/16"(268)

4-9/16" (116)Jamb Width*

1-5/16" (33)

4-9/16" * (116)*

5-7/16" (138)5-7/16" (138)

1-3/4" (44)1-3/4" (44)


Minimum Rough Opening Width3/8" (10)3/8" (10)

Center LineMeeting

Stiles

2'-5 5/8" 2'-5 5/8" 2'-11 5/8" 2'-11 5/8" 3'-115/8" 3'-115/8"

(905) (905)(752) (752) (1210) (1210)

1-3/4" (44)3/4" (19)

3/4" (19)

1-3/8" (35) 1-3/8" (35)

2" (51)

2" (51) 1-3/4" (44)


Sidelight Details Scale 1-1/2" = 1'-0" (1:8)

• Rough opening dimensions may need to be increased to allow for use of building wraps,

�ashing, sill panning, brackets, fasteners or other items. See page 7 for more information.

* 4-9/16" measurement is from backside of �ange to inside edge of door frame.

• For Miami-Dade county installations, please refer to Notice of Acceptance Report.

• Andersen recommends installation of doors into separate rough openings. Consult with an architect or structural engineer regrading minimum requirements for structural support members between adjacent door rough openings.




CAUTION: In masonry wall construction, provide a minimum of 1/2" clearance from the top of the brick or masonry to the bottom of any portion of the sill. Failure to do so could result in product damage.

Fill the void with closed cell foam backer rod and sealant. Be sure to allow for dimensional change of framework.

Head

Sill

Jamb Jamb

Center Line Astragal Dimensions

5-0 WIDTHS 6-0 WIDTHS 8-0 WIDTHS

Support Mullion







The sum of individual Unit Dimension Widths, plus 3/4" (19mm) for each unit joining.





Frenchwood®

Hinged Patio Doors Inswing

True Andersen classics, these patio doors emphasize beauty and

performance. They open inward and, like all Andersen® 400 Series

products, are available with a full range of options and accessories.

Section Reference




Joining Details ..................... 59





400

F

renc

hwoo

d®Hi

nged

Patio

Doo

rs–I

nswi

ng

Features

Frenchwood® Hinged Patio Doors - Inswing

Five-Point Locking SyStem

On active/passive door configurations,

a five-point lock features stainless steel latches that engage into the sill, head jamb and passive panel for added security and performance.

moRtiSe-and- tenon JointS

Mortise-and-tenon joints help prevent panel sag and maintain smooth operation.





FRame

The sill of the Frenchwood® hinged

patio door – inswing is made with three-piece construction. The subsill is made of vinyl material, and the sill step is solid oak or maple. The exterior sill member is made of extruded aluminum with an attractive wear-resistant, corrosion- resistant, heat-baked finish in a neutral color. This combination of materials combines durability and low maintenance with excellent insulating characteristics.

All basic exterior frame members are made of a glass fiber reinforced composite, which maintains an attractive appearance while minimizing maintenance. Andersen® Frenchwood hinged patio doors – inswing are available in four neutral colors. Specify White, Sandtone, Terratone® or Forest Green color.

The exterior frame members are attached to a water-repellent preservative-treated wood subframe for long-lasting* protection and performance.

The subframe is grooved to accept extension jambs.

PaneL



Hinged inswing operating panels are either left or right-hand active.

A factory-applied, one-piece compression-type rubber weatherstrip continues in one plane around the panel to provide maximum effectiveness against water and air infiltration. The corners of the weatherstrip are welded to eliminate gaps between the panel and the frame/sill shoulder.

adJuStabLe HingeS

Adjustable hinges have ball bearing pivots for smooth, frictionless movement. Features easy horizontal and vertical adjustment, plus quick release feature for easy panel removal. Brass tone finish is standard on wood interior doors. For units with a white prefinished interior, white finish hinges are standard. Also available in factory-applied finishes that coordinate with hardware. Hardware is sold separately.

gLaSS

Panels are silicone bed and

back glazed and finished with an interior wood stop and an exterior silicone bead.


• Standard High-Performance™ Low-E4® tempered glass (PG Upgrade)

• Standard High-Performance™ Low-E4® Sun tempered glass (PG Upgrade)

• Standard High-Performance™ Low-E4® SmartSun™ tempered glass (PG Upgrade)



• High-Performance™ Low-E4® SmartSun™ tempered impact- resistant glass


exterior interior

White Sandtone Terratone® ForestGreen pine oak maplewhite



54

brightbrass

antiquebrass

polishedchrome

brushedchrome

satinnickel

oilrubbedbronze

distressednickel

distressedbronze


Hardware Finishes




white

stone

gold dust

black

white

stone

bright brass

satin nickel

oil rubbed bronze

bright brass

antique brass

polished chrome

brushed chrome

satin nickel

oil rubbed bronze

bright brass

antique brass

oil rubbed bronze

bright brass

antique brass

satin nickel

oil rubbed bronze

distressed nickel

distressed bronze

distressed nickel

distressed bronze

55

CAUTION: • Painting and staining may cause

damage to rigid vinyl. • Products in Sandtone or Terratone®







NOTE: Andersen® patio doors are not intended for use as entrance doors.


"Delrin" is a registered trademark of E.I. duPont deNemours and Company.


Sill Support

An aluminum sill support is designed to lock into a channel under the sill and tie back into the wall. This will offer support to the outermost sill section when needed. Available in neutral gray finish.

Ramped Sill InsertProvides smooth transition from interior to exterior. Cannot be used with insect screen. Not available on outswing door. (Specifier must check with local and federal officials to determine if product meets accessibility codes.)

HaRdwaRe

Exterior Keyed LockA six-pin exterior key cylinder lock is available for all patio doors in styles and finishes that coordinate with hardware. This lock allows the patio door to be locked and unlocked from the exterior. See page 63 for photo.

Handle Extension KitExtends interior door handle an additional 1'' (25) from the door panel to accommodate interior blinds or shades. Kit includes one handle extender and spindle. A second extender may be added to the spindle to increase the length an additional 1'' (25) (2'' (51) total extension). See page 63 for photo.

HingesA variety of hinge finishes are available factory-applied, or for after-market installation. Finish options coordinate with handle hardware and are available in bright brass, antique brass, polished chrome, brushed chrome, satin nickel, oil rubbed bronze, distressed nickel, and distressed bronze.

PaneL

Panel StopThis hinged door panel stop helps prevent wall damage when opening the inswing door. Available in finishes that coordinate with hardware.

Double Insect Screen TrackAn extended insect screen track is available for double jamb hinged doors that use gliding insect screens.

SideLigHtS and tRanSomS

Andersen® Frenchwood® patio door sidelights and transoms feature elegant lines that match our 400 Series Frenchwood hinged patio doors. They feature pine, oak, maple or prefinished white interior options, plus our four standard exterior colors.

Like the doors they complement, Andersen sidelights and transoms are available with Stormwatch® protection. Size information available on pages 68-69.

FRame

Extension JambsStandard jamb depth is 4-9/16'' (119). Clear pine, oak or maple veneer or white interior extension jambs are available for the following wall thicknesses:

• 5-1/4'' (133) • 6-9/16'' (167) • 7-1/8'' (181)

Bright brass, antique brass, polished chrome, oil rubbed bronze, brushed chrome and satin nickel strike plate extensions are available for single hinge doors.

Exterior extension jamb system is available for the following wall thicknesses:

• 5-1/4'' (133) • 6-9/16'' (167) • 7-9/16'' (192)

In walls over 4-1/2'' (114), the exterior sill extender and exterior extension jamb system allow the unit to be installed flush to the interior, so the hinged doors will open flat against the interior wall. Colored to match the exterior of the finished unit, this system provides a low-maintenance, finished exterior appearance. An extended double insect screen track is available for double-jamb hinged doors that require gliding insect screens. Exterior jamb kits are available with or without the double-insect screen track.

ThresholdAn oak or maple threshold is available for finishing the interior of the sill.

inSect ScReenS

Hinged Insect Screen Available for single-panel doors.

Double-Hinged Insect ScreenAvailable for two-panel double jamb hinged doors.

Gliding Insect ScreenAvailable for all two- and three-panel doors. Features Delrin® material injection molded bottom rollers with self-contained leveling adjusters. A double insect screen track kit and two universal gliding insect screens are required for installation. Gliding insect screens are not available for 4'0'' wide doors.

All insect screens are available in White, Sandtone, Terratone® and Forest Green colors.

Pg uPgRadeS

Frenchwood® HingedPatio Doors - InswingPG Upgrades are available for select sizes only. Ask your Andersen supplier for details.

inStaLLation acceSSoRieS


gRiLLeS


gLaSS



400

F

renc

hwoo

d®Hi

nged

Patio

Doo

rs–I

nswi

ng

56


Grille order numberr:FWH2168 FWH2180FWH21611

Grille order number:FWH2768 FWH2780FWH27611



6'-7

1/ 2

"

6'-8

"

63 1

/ 2"

(201

9)

(161

3)

(20

32)

6'-1

1" (2

108)

6'-1

0 3 /

8"(2

092)

66 3

/ 8"

(168

6)

7'-1

1 1 /

2"

8'-0

" (2

438)

(242

6)

79 1

/ 2" (

2019

)

Unit Dimension


Unobstructed Glass

4'-1" 4'-1"

4'-0" 4'-0"

131/4 131/4" 131/4" 131/4" 131

111 11

/4""

2'-1"

2'-0 1/2"

Availablein

3 heights

(1219)

(1242)

(1219)

(1242)

(336) (336)(336) (336)(336)

(620)

(634)

2'-7"

2'-6 /8"

2'-7" 2'-7" 5'-0" 5'-0"

2'-6 /8" 2'-6 /8" 4'-11 /4" 4'-11 /4"

18 7/8"

Unit Dimension


Unobstructed Glass

Availablein

3 heights

(765)

(787)

(765)

(787)

(765)

(787)

(1504)

(1524)

(1504)

(1524)

(479)18 7/8" (479)

18 7/8" (479)

18 7/8" (479)

18 7/8" (479)

18 7/8" (479)

18 7/8" (479)

2'-9"

2'-8 1/8"

2'-9" 2'-9"

2'-8 1/8" 2'-8 1/8"

5'-4"

5'-3 1/4"

5'-4"

5'-3 1/4"

207/8" 207/8" 207/8" 207/8" 207/8" 207/8" 207/8"

Availablein

3 heights

(816)

(838)

(816)

(838)

(816)

(838)

(1607)

(1626)

(1607)

(1626)

(530) (530)(530) (530)(530)(530)(530)

Unit Dimension


Unobstructed Glass

3'-1"3'-1"3'-1"

3'-0 1/8"

6'-0" 6'-0"

3'-0 1/8" 3'-0 1/8" 5'-11 1/4" 5'-11 1/4"

24 7/8" 24 7/8" 24 7/8" 24 7/8" 24 7/8" 24 7/8" 24 7/8"

(918) (918)

(940) (940)

(1810)

(1829)

(918)

(940)

(1810)

(1829)

(632) (632) (632) (632) (632) (632) (632)

Availablein

3 heights

Unit Dimension


Unobstructed Glass



• Andersen® art glass panels are available for all units on this page.


• Combinations of door units joined together may require horizontal or vertical reinforcement. This reinforcement should be speci�ed by a professional engineer.


• When ordering, be sure to specify product type: High-Performance™ Low-E4® impact-resistant or PG Upgrade.

FWH2768ALFWH27611ALFWH2780AL

FWH2768SFWH27611SFWH2780S

FWH5068PALRFWH50611PALRFWH5080PALR

FWH5068APLRFWH50611APLRFWH5080APLR



1 FWH2168S2 FWH21611S3 FWH2180S

1 FWH2768AR2 FWH27611AR3 FWH2780AR

1 FWH xx68

2 FWH xx611

3 FWH xx80












1/8" increments

1/ 8

" in

crem

ents


Three Basic Unit Heights

Custom Sizes


pattern

57

Clear Opg. Width 90°

Clear Opening WidthFull Open Position

1-11/16" (43)1/2" (13)

Clea

r Ope

ning

Hei

ght

Clear Opening Dimensions Scale 1-1/2" = 1'-0" (1:8)

Astragal

Horizontal SectionActive / Passive Panels Open

Vertical SectionPassiveActive

Sill

Head


Frenchwood® Hinged Patio Door – Inswing 6' 8" Height

Unit Number

Sq. Ft. (m2) Clear

Opening

Maximum Clear OpeningSquare

Feet (m2) Glass

Square Feet

(m2) Vent

Overall Unit Area

Sq. Ft. (m2)

Width inches (mm) Height inches(mm)90° Full

2768 12.98 24-13/16" 26" 75-1/4" 8.32 12.98 16.63(1.206) (630) (660) (1911) (0.773) (1.206) (1.545)

2968 14.02 26-13/16" 28" 75-1/4" 9.20 14.02 17.74(1.303) (681) (711) (1911) (0.855) (1.303) (1.648)

3168 16.11 30-13/16" 32" 75-1/4" 10.96 16.11 19.95(1.497) (783) (813) (1911) (1.018) (1.497) (1.853)

4168AP/PA 21.43 41" 43-7/8" 75-1/4" 11.68 21.43 26.50(1.991) (1039) (1112) (1911) (1.085) (1.991) (2.462 )

4168AP/PA(panel closed)

21.43 19-7/8" 21-1/16" 75-1/4" 11.68 21.43 26.50(1.991) (505) (535) (1911) (1.085) (1.991) (2.462 )

5068AP/PA 27.30 52-1/4" 55-1/8" 75-1/4" 16.64 27.30 32.71(2.536) (1327) (1400) (1911) (1.546) (2.536) (3.039)


27.30 25-1/2" 26-11/16" 75-1/4" 16.64 27.30 32.71(2.536) (647) (678) (1911) (1.546) (2.536) (3.039)

5468AP/PA 29.39 56-1/4" 59-1/8" 75-1/4" 18.39 29.39 34.92(2.730) (1429) (1502) (1911) (1.708) (2.730) (3.244)


29.39 27-1/2" 28-11/16" 75-1/4" 18.39 29.39 34.92(2.730) (698) (729) (1911) (1.708) (2.730) (3.244)

6068AP/PA 33.58 64-1/4" 67-1/8" 75-1/4" 21.92 33.58 39.34(3.120) (1632) (1705) (1911) (2.036) (3.120) (3.655)


33.58 31-1/2" 32-11/16" 75-1/4" 21.92 33.58 39.34(3.120) (800) (830) (1911) (2.036) (3.120) (3.655)


Unit Number

Sq. Ft. (m2) Clear

Opening


Feet (m2) Glass

Square Feet

(m2) Vent

Overall Unit Area

Sq. Ft. (m2)


27611 13.48 24-13/16" 26" 78-1/8" 8.69 13.48 17.21(1.252) (630) (660) (1984) (0.807) (1.252) (1.599)

29611 14.55 26-13/16" 28" 78-1/8" 9.61 14.55 18.36(1.352) (681) (711) (1984) (0.893) (1.352) (1.706)

31611 16.72 30-13/16" 32" 78-1/8" 11.45 16.72 20.64(1.553) (783) (813) (1984) (1.064) (1.553) (1.918)

41611AP/PA 22.24 41" 43-7/8" 78-1/8" 12.20 22.24 27.46(2.066) (1039) (1112) (1984) (1.133) (2.066) (2.551)


22.24 19-7/8" 21-1/16" 78-1/8" 12.20 22.24 27.46(2.066) (505) (535) (1984) (1.133) (2.066) (2.551)

50611AP/PA 28.34 52-1/4" 55-1/8" 78-1/8" 17.38 28.34 33.89(2.633) (1327) (1400) (1984) (1.615) (2.633) (3.148)


28.34 25-1/2" 26-11/16" 78-1/8" 17.38 28.34 33.89(2.633) (647) (678) (1984) (1.615) (2.633) (3.148)

54611AP/PA 30.51 56-1/4" 59-1/8" 78-1/8" 19.22 30.51 36.18(2.834) (1429) (1502) (1984) (1.786) (2.834) (3.361)


30.51 27-1/2" 28-11/16" 78-1/8" 19.22 30.51 36.18(2.834) (698) (729) (1984) (1.786) (2.834) (3.361)

60611AP/PA 34.86 64-1/4" 67-1/8" 78-1/8" 22.91 34.86 40.76(3.239) (1632) (1705) (1984) (2.128) (3.239) (3.787)


34.86 31-1/2" 32-11/16" 78-1/8" 22.91 34.86 40.76(3.239) (800) (830) (1984) (2.128) (3.239) (3.787)

400

F

renc

hwoo

d®Hi

nged

Patio

Doo

rs–I

nswi

ng

58




Clear Opening Dimensions Scale 1-1/2" = 1'-0" (1:8)

Horizontal SectionActive Panel Open

Astragal PassiveActive

Unit Identi�cationUnits viewed from the exterior

Basic Hinging

Left HingedHinges mounted on the left side of the panel.

Right HingedHinges mounted on the right side of the panel.

Active PanelThe operating panelmost often used.

Passive PanelThe operating panel with astragal attached.

Stationary PanelNon-operating panel.

Double Jamb Hinged Door

Order Designation Description

FWH 6068 A P L R

Frenchwood®

hinged door(Inswing) Door

rough opg.

Activepanel

Passivepanel

Right hinged

Left hinged


2'-115/8" 2'-115/8"

2'-5 5/8" 2'-5 5/8"

2'-7 5/8" 2'-7 5/8"

(897) (897)

(752) (752)

(803) (803)

6-0 WIDTHS

5-4 WIDTHS

5-0 WIDTHS

2'-0" 2'-0"

(610) (610)4-1 WIDTHS



Unit Number

Sq. Ft. (m2) Clear

Opening


Feet (m2) Glass

Square Feet

(m2) Vent

Overall Unit Area

Sq. Ft. (m2)


2780 15.73 24-13/16" 26" 91-1/4" 10.41 15.73 19.98(1.461) (630) (660) (2318) (0.967) (1.461) (1.856)

2980 17.00 26-13/16" 28" 91-1/4" 11.52 17.00 21.31(1.579) (681) (711) (2318) (1.070) (1.579) (1.980)

3180 19.54 30-13/16" 32" 91-1/4" 13.72 19.54 23.96(1.815) (783) (813) (2318) (1.275) (1.815) (2.226)

4180AP/PA 25.98 41" 43-7/8" 91-1/4" 14.62 25.98 31.83(2.414) (1039) (1112) (2318) (1.358) (2.414) (2.957)


25.98 19-7/8" 21-1/16" 91-1/4" 14.62 25.98 31.83(2.414) (505) (535) (2318) (1.358) (2.414) (2.957)

5080AP/PA 33.11 52-1/4" 55-1/8" 91-1/4" 20.82 33.11 39.30(3.076) (1327) (1400) (2318) (1.934) (3.076) (3.651)


33.11 25-1/2" 26-11/16" 91-1/4" 20.82 33.11 39.30(3.076) (647) (678) (2318) (1.934) (3.076) (3.651)

5480AP/PA 35.64 56-1/4" 59-1/8" 91-1/4" 23.03 35.64 41.95(3.311) (1429) (1502) (2318) (2.140) (3.311) (3.897)


35.64 27-1/2" 28-11/16" 91-1/4" 23.03 35.64 41.95(3.311) (698) (729) (2318) (2.140) (3.311) (3.897)

6080AP/PA 40.71 64-1/4" 67-1/8" 91-1/4" 27.44 40.71 47.25(3.782) (1632) (1705) (2318) (2.549) (3.782) (4.390)


40.71 31-1/2" 32-11/16" 91-1/4" 27.44 40.71 47.25(3.782) (800) (830) (2318) (2.549) (3.782) (4.390)

59



3/8" (10) 3/8" (10)

Andersen exteriorextension jamb

Insect screen door

Metro™ Collection,Tribeca® handle

Min

imum

Rou

gh O

peni

ng H

eigh

t

Unit

Dim

ensi

on H

eigh

t

Andersen® exteriorextension jamb

Andersen sill extender


Optionaloak or maplethreshold

3/4" (19)

3/4" (19)

1" (25)1" (25)


2" (51)

2" (51)

1" (25) 1" (25)


81

1/2"(13)

1-7/16"(37)

1/4"(6)

Note:Cannot be used with insect screen.



Support Mullion










Consult with an architect or structural engineer regarding minimum requirements for structural support members between adjacent door rough openings.

Ramped Sill Details Scale 1-1/2" = 1'-0" (1:8)

Vertical Section

Horizontal Section

Vertical Section—Ramped Sill

Sill

Head

Jamb Jamb

400

F

renc

hwoo

d®Hi

nged

Patio

Doo

rs–I

nswi

ng

60


1" (25) 1" (25)

5-5/8" (143) 5-5/8" (143) 5-1/8" (130) 5-1/8" (130)

50*= 2' 5-5/8" (752)54*= 2' 7-5/8" (803)60*= 2' 11-5/8" (905)

LC

3/8" (10)Unit Dimension Width

3/8" (10)Minimum Rough Opening Width

50*= 2' 5-5/8" (752)54*= 2' 7-5/8" (803)60*= 2' 11-5/8" (905)

Andersen double screen track kit


Minimum Rough Opening Width3/8"(10)

3/8"(10)

3/4" x 3-1/2"(19 x 89)vinyl trim board

Andersen®

rigid vinyl3/4" (19)"h" channel

3/4" (19)

2" x 3" (51 x 76)pre�nished break metalclosure "L"(by others)

Remove�ashing �angeat head and jamb


Andersenoptional PVC spacerand sill extension

Andersenoptional oak ormaple threshold

3/8" (10)

Extend and attachvapor barrier tounit frame (by others)

Andersenoptionalinsect screen

Unit

Dim

ensi

on H

eigh

t

Unit

Dim

. Wid

th

Roug

h Op

enin

g He

ight

Metro™ Collection,Tribeca® handle

* These dimensions relate to location of astragal center line.

Rough opening dimensions may need to be increased to allow for use of building wraps,

�ashing, sill panning, brackets, fasteners or other items. See page 7 for more details.

Jamb JambAstragal

Active Panel Passive Panel

JambJamb

Stationary Panel

Basic Unit Details Scale 1-1/2" = 1'-0" (1:8)

Horizontal SectionStationary Panel

Horizontal SectionDouble Jamb Hinged Door

Suggested Product Applications Scale 1-1/2" = 1'-0" (1:8)

Sill

2" x 6" WallDetail showing unit installed in a 2 x 6 stud wall

Head

Jamb

Proper installation and maintenance of Andersen products is essential to attain optimum performance and operation. Written installation instructions which provide guidelines for proper installation are typically provided with Andersen products. They are also available from your local Andersen supplier or by visiting andersenwindows.com. Remember that every installation is different, and Andersen strongly recommends consultation with the local supplier or an experienced contractor, architect or structural engineer prior to the installation of any Andersen product. The method of attachment for Andersen products, fastener selection and code compliance is the responsibility of the architect, building owner, contractor, installer and/or consumer. For complete installation details, refer to “Product Installation Details” at andersenwindows.com or contact your Andersen supplier.


CAUTION: In masonry wall construction, provide a minimum of 1/2" clearance from the top of the brick or masonry to the bottom of any portion of the sill. Failure to do so could result in product damage. Fill the void with closed cell foam backer rod and silicone sealant. Be sure to allow for dimensional change of framework.

Jamb hinged patio door in 2" x 6" wall without extension jambs

Jamb hinged patio door in 2" x 6" wall with extension jambs

Interior Extension Jambs

The use of interior extension jambs or drywall return will restrict panel operation on jamb hinged doors. Jamb hinged patio doors must be installed �ush to the interior to achieve full panel operation.

Installed �ush to interior wall

Full panel operation

Exterior trim and�ashing by others

Optional Andersen® extension jambs

Restricted paneloperation

Frenchwood®

Hinged Patio Doors Outswing

Section Reference




Joining Details ..................... 66





Built to function beautifully, these doors can save up to 28 square feet

of interior space. They feature quick-release removable panels for ease

of installation and finishing.

400

F

renc

hwoo

d®Hi

nged

Patio

Doo

rs–O

utsw

ing

62

Features

Frenchwood® Hinged Patio Doors - Outswing

Five-Point Locking SyStem

On active/passive door configurations,

a five-point lock features stainless steel latches that engage into the sill, head jamb and passive panel for added security and performance.

moRtiSe-and -tenon JointS

Mortise-and-tenon joints help prevent panel sag and maintain smooth operation.





FRame

The 1-1/4'' (32) sill has a thermal break to help keep heat and cold out. The panels and frame have superior strength and insulating properties and an attractive, wear-resistant, corrosion-resistant,* heat-baked, low-maintenance finish.

All basic exterior frame members are glass fiber reinforced composite, which maintains an attractive appearance while minimizing maintenance. Andersen® Frenchwood® hinged patio doors – outswing are available in four neutral colors. Specify White, Sandtone, Terratone® or Forest Green color.

The frame members are attached to a water- repellent preservative-treated wood subframe for long- lasting* protection and performance. The subframe is grooved to accept extension jambs.

PaneL



Hinged outswing operating panels are available in either single left- or right-hand active or two panel active/passive jamb hinges.

A factory-applied, one-piece, compression-type rubber weatherstrip continues in one plane around the panel to provide maximum effectiveness against water and air infiltration. The corners of the weatherstrip are welded to eliminate gaps between the panel and the frame/sill shoulder. The weatherstripping creates a strong, long-lasting* seal that stands up to harsh weather. The weatherstripping is directly attached to the panel, not to the frame.

The ball bearing hinges are covered with a corrosion-resistant powder-coat finish. All hinges are color-matched to the panel exterior and can be adjusted up/down and left/right after installation.

gLaSS

Panels are silicone bed glazed and finished with an interior wood stop and an exterior silicone bead.

The interior wood stops are secured

using 1-1/2'' 16-gauge crown staples instead of nails.

Consult local building codes for

glass most suitable to your area. Glass options include:

• Standard High-Performance™ Low-E4® tempered glass (PG Upgrade)

• Standard High-Performance™ Low-E4® Sun tempered glass (PG Upgrade)

• Standard High-Performance™ Low-E4® SmartSun™ tempered glass (PG Upgrade)



• High-Performance™ Low-E4® SmartSun™ tempered impact- resistant glass




exterior interior

White Sandtone Terratone® ForestGreen pine oak maplewhite



brightbrass

antiquebrass

polishedchrome

brushedchrome

satinnickel

oilrubbedbronze

distressednickel

distressedbronze


Hardware Finishes




white

stone

gold dust

black

white

stone

bright brass

satin nickel

oil rubbed bronze

bright brass

antique brass

polished chrome

brushed chrome

satin nickel

oil rubbed bronze

bright brass

antique brass

oil rubbed bronze

bright brass

antique brass

satin nickel

oil rubbed bronze

distressed nickel

distressed bronze

distressed nickel

distressed bronze


63










NOTE: Andersen® patio doors are not intended for use as entrance doors.



HaRdwaRe

Exterior Keyed LockA six-pin exterior key cylinder lock is available for all patio doors in finishes that coordinate with hardware. This lock allows the patio door to be locked and unlocked from the exterior.

Handle Extension KitExtends interior door handle an additional 1'' (25) from the door panel to accommodate interior blinds or shades. Kit includes one handle extender and spindle. A second extender may be added to the spindle to increase the length an additional 1'' (25) (2'' (51) total extension).

gRiLLeS


inSect ScReen

Perma-Clean® Retractable Insect ScreenThe retractable insect screen is installed on the interior of the door across the width of the opening. When the insect screen is not in use, it neatly retracts into small canisters mounted on each side of the door. Retractable insect screens are available for single-panel and two-panel doors with white frame/canister finish. Please note, retractable screen track reduces clear opening height by 1''.

SideLigHtS and tRanSomS

Andersen Frenchwood patio door sidelights and transoms feature elegant lines that match our 400 Series Frenchwood hinged patio doors. They feature pine, oak, maple or prefinished white interior options, plus our four standard exterior colors.

Like the doors they complement, Andersen sidelights and transoms are available with Stormwatch® protection. Size information available on pages 68-69.

inStaLLation acceSSoRieS


Removable PanelsRemovable panels simplify finishing and allow for easy storage during construction. The panel release tabs on the hinge are covered with a cap for a clean appearance.

The panels can be easily removed with the unique panel release tab on the hinge. This release feature is ideal for transporting large units up stairs or to other hard-to-reach areas.

FRame

Extension JambsStandard jamb depth is 4-9/16'' (119). Clear pine, oak or maple veneer or white interior extension jambs are available for the following wall thicknesses:

• 5-1/4'' (133) • 6-9/16'' (167) • 7-1/8'' (181)

Sill Support

An aluminum sill support is designed to lock into a channel under the sill and tie back into the wall. This will offer support to the outermost sill section when needed. Available in neutral gray finish.

Sill StepThe Frenchwood® outswing door offers an optional oak or maple sill step.

gLaSS

Andersen® Art GlassAndersen art glass panels come in eleven original patterns, including four Frank Lloyd Wright ® series designs. See the Andersen ® Product Guide for details on Andersen art glass or visit andersenwindows.com/artglass for pattern information.

Pg UPgRadeS

Frenchwood® HingedPatio Doors - OutswingPG Upgrades are available for select sizes only. Ask your Andersen supplier for details.

400

F

renc

hwoo

d®Hi

nged

Patio

Doo

rs–O

utsw

ing


64

Frenchwood® Hinged Patio Doors - Outswing

Grille order number:FWH2168 FWH2768 FWH2180 FWH2780FWH21611 FWH27611

2'-7"

2'-6 1/8"

2'-7" 2'-7" 5'-0" 5'-0"

2'-6 1/8" 2'-6 1/8" 4'-11 1/4" 4'-11 1/4"

187/8" 187/8" 187/8" 187/8" 187/8" 187/8" 187/8"

4'-1" 4'-1"

4'-0" 4'-0"

131/4" 131/4" 131/4" 131/4" 131/4"

(1219)

(1242)

(1219)

(1242)

(336) (336)(336) (336)(336)

(765)

(787)

(765)

(787)

(765)

(787)

(1504)

(1524)

(1504)

(1524)

(479) (479) (479) (479) (479) (479) (479)

2'-1"

2'-01/2"

(620)

(634)

Availablein

3 heights

FWO 2768ALFWO 27611ALFWO 2780AL

FWO 2768SFWO 27611SFWO 2780S

FWO 5068PALRFWO 50611PALRFWO 5080PALR

FWO 5068APLRFWO 50611APLRFWO 5080APLR



1 FWO 2168S2 FWO 21611S3 FWO 2180S

FWO 2768ARFWO 27611ARFWO 2780AR

6'-7

1/ 2

"

6'-8

"

63 1

/ 2"

(201

9)

(161

3)

(2

032)

1 FWO xx68 2 FWO xx611 3 FWO xx80

6'-1

1" (

2108

)

6'-1

0 3 /

8"(2

092)

66 3

/ 8"

(168

6)

7'-1

1 1 /

2"

8'-0

" (2

438)

(242

6)

79 1

/ 2" (

2019

)

• Rough opening dimensions may need to be increased to allow for use of building wraps, ashing, sill panning, brackets, fasteners or other items. See page 7 for more details.• “Unit Dimension” always refers to outside frame to frame dimension.• Andersen® art glass panels are available for all units on this page.• Dimensions in parentheses are in millimeters.• Combinations of door units joined together may require horizontal or vertical reinforcement. This reinforcement should be speci�ed by a professional engineer.• When ordering, be sure to specify color desired: White, Sandtone, Terratone® or Forest Green.• When ordering, be sure to specify product type: High-Performance™ Low-E4® impact-resistant, monolithic impact-resistant or PG Upgrade.• For Miami-Dade County installations, please refer to Notice of Acceptance Report.

Unit Dimension


Unobstructed Glass


Order Designation Description

FWO 6068 A P L R

Frenchwood®

Outswing Door

Doorrough opg.

Activepanel

Passivepanel

Right hinged

Left hinged



Unit Dimension


Unobstructed Glass

Unit Dimension


Unobstructed Glass

2'-9"

2'-8 1/8"

2'-9" 2'-9"

3'-1"3'-1"3'-1"

3'-0 1/8"

6'-0" 6'-0"

2'-8 1/8" 2'-8 1/8"

3'-0 1/8" 3'-0 1/8" 5'-11 1/4" 5'-11 1/4"

5'-4"

5'-3 1/4"

5'-4"

5'-3 1/4"

24 7/8"

207/8"

24 7/8" 24 7/8" 24 7/8" 24 7/8" 24 7/8" 24 7/8"

(816)

(838)

(816)

(838)

(918) (918)

(940) (940)

(1810)

(1829)

(816)

(838)

(918)

(940)

(1810)

(1829)

(1607)

(1626)

(1607)

(1626)

(632)

(530)

207/8"

(530)

207/8"

(530)

207/8"

(530)

207/8"

(530)

207/8"

(530)

207/8"

(530)

(632) (632) (632) (632) (632) (632)

Availablein

3 heights

Availablein

3 heights









1 FWO 2968AR2 FWO 29611AR3 FWO 2980AR

1 FWO 3168AR2 FWO 31611AR3 FWO 3180AR


2'-115/8" 2'-115/8"

2'-5 5/8" 2'-5 5/8"

2'-7 5/8" 2'-7 5/8"

(897) (897)

(752) (752)

(803) (803)

6-0 WIDTHS

5-4 WIDTHS

5-0 WIDTHS

2'-0" 2'-0"

(610) (610)4-1 WIDTHS

1/8" increments

1/ 8

" in

crem

ents


Three Basic Unit Heights Custom Sizes


pattern

65


Roug

h Op

enin

g He

ight

Unit

Dim

ensi

on H

eigh

t

Clea

r Ope

ning

Hei

ght

Head

Sill

Optional Sill Support

Andersen®

optional retractableinsectscreen

3/8" (10)3/8" (10)Unit Dimension Width


Jamb Jamb

Andersen® optional retractable insect screen

Tribeca® handle hardware



Unit Identi�cation Units viewed from the exterior

Basic Hinging

Left HingedHinges mounted on the left side of the panel.

Right HingedHinges mounted on the right side of the panel.

Active PanelThe operating panel most often used.

Passive PanelThe operating panel with astragal attached.

Stationary PanelNon-operating panel.

Double Jamb Hinged Door


Frenchwood® Hinged Patio Door – Outswing 6' 8" Height

Unit Number

Sq. Ft. (m2) Clear

Opening

Maximum Clear Opening

GlassSq. Ft. (m2)

VentSq. Ft. (m2)

Overall Unit Area

Sq. Ft. (m2)


2768 13.34 25-1/8" 26-11/16" 76-1/2" 8.32 13.34 16.62(1.239) (637) (678) (1943) (0.773) (1.239) (1.544)

2968 14.40 27-1/8" 28-11/16" 76-1/2" 9.20 14.40 17.72(1.338) (688) (729) (1943) (0.855) (1.338) (1.646)

3168 16.53 31-1/8" 32-11/16" 76-1/2" 10.96 16.53 19.93(1.536) (790) (830) (1943) (1.018) (1.536) (1.852)

4168AP/PA 21.98 41-7/16" 44-5/8" 76-1/2" 11.67 21.98 26.48(2.042) (1053) (1133) (1943) (1.084) (2.042) (2.460)


21.98 19-3/8" 20-7/8" 76-1/2" 11.67 21.98 26.48(2.042) (492) (530) (1943) (1.084) (2.042) (2.460)

5068AP/PA 27.95 52-5/8" 55-13/16" 76-1/2" 16.64 27.95 32.68(2.597) (1337) (1418) (1943) (1.546) (2.597) (3.036)

5068A/PA(panel closed)

27.95 25" 26-1/2" 76-1/2" 16.64 27.95 32.68(2.597) (635) (673) (1943) (1.546) (2.597) (3.036)

5468AP/PA 30.08 56-5/8" 59-13/16" 76-1/2" 18.39 30.08 34.89(2.795) (1438) (1519) (1943) (1.708) (2.795) (3.241)


30.08 27" 28-1/2" 76-1/2" 18.39 30.08 34.89(2.795) (685) (723) (1943) (1.708) (2.795) (3.241)

6068AP/PA 34.33 64-5/8" 67-13/16" 76-1/2" 21.92 34.33 39.30(3.189) (1641) (1723) (1943) (2.036) (3.189) (3.651)


34.33 31" 32-1/2" 76-1/2" 21.92 34.33 39.30(3.189) (787) (826) (1943) (2.036) (3.189) (3.651)

Frenchwood® Hinged Patio Door – Outswing 6' 11" Height27611 13.84 25-1/8” 26-11/16" 79-3/8" 8.69 13.84 17.22

(1.286) (637) (678) (2016) (0.807) (1.286) (1.600)29611 14.94 27-1/8" 28-11/16" 79-3/8" 9.61 14.94 18.36

(1.388) (688) (729) (2016) (0.893) (1.388) (1.706)31611 17.15 31-1/8" 32-11/16" 79-3/8" 11.45 17.15 20.65

(1.593) (790) (830) (2016) (1.064) (1.593) (1.918)41611AP/PA 22.80 41-7/16" 44-5/8" 79-3/8" 12.20 22.80 27.44

(2.118) (1053) (1133) (2016) (1.133) (2.118) (2.549)41611AP/PA(panel closed)

22.80 19-3/8" 20-7/8" 79-3/8" 12.20 22.80 27.44(2.118) (492) (530) (2016) (1.133) (2.118) (2.549)

50611AP/PA 29.00 52-5/8" 55-13/16" 79-3/8" 17.38 29.00 33.87(2.694) (1337) (1418) (2016) (1.615) (2.694) (3.147)

50611A/PA(panel closed)

29.00 25" 26-1/2" 79-3/8" 17.38 29.00 33.87(2.694) (635) (673) (2016) (1.615) (2.694) (3.147)

54611AP/PA 31.21 56-5/8" 59-13/16" 79-3/8" 19.22 31.21 36.15(2.900) (1438) (1519) (2016) (1.786) (2.900) (3.358)

54611P/PA(panel closed)

31.21 27" 28-1/2" 79-3/8" 19.22 31.21 36.15(2.900) (685) (723) (2016) (1.786) (2.900) (3.358)

60611AP/PA 35.62 64-5/8" 67-13/16" 79-3/8" 22.91 35.62 40.73(3.309) (1641) (1723) (2016) (2.128) (3.309) (3.784)


35.62 31" 32-1/2" 79-3/8" 22.91 35.62 40.73(3.309) (787) (826) (2016) (2.128) (3.309) (3.784)

Frenchwood® Hinged Patio Door – Outswing 8' 0" Height2780 16.13 25-1/8" 26-11/16" 92-1/2" 10.41 16.13 19.96

(1.499) (637) (678) (2350) (0.967) (1.499) (1.854)2980 17.42 27-1/8" 28-11/16" 92-1/2" 11.52 17.42 21.29

(1.618) (688) (729) (2350) (1.070) (1.618) (1.978)3180 19.99 31-1/8" 32-11/16" 92-1/2" 13.72 19.99 23.94

(1.857) (790) (830) (2350) (1.275) (1.857) (2.224)4180/PA 26.57 41-7/16" 44-5/8" 92-1/2" 14.62 26.57 31.81

(2.468) (1053) (1133) (2350) (1.358) (2.468) (2.955)4180/PA 26.57 19-3/8" 20-7/8" 92-1/2" 14.62 26.57 31.81

(2.468) (492) (530) (2350) (1.358) (2.468) (2.955)5080AP/PA 33.80 52-5/8" 55-13/16" 92-1/2" 20.82 33.80 39.27

(3.140) (1337) (1418) (2350) (1.934) (3.140) (3.648)5080AP/PA(panel closed)

33.80 25" 26-1/2" 92-1/2" 20.82 33.80 39.27(3.140) (635) (673) (2350) (1.934) (3.140) (3.648)

5480AP/PA 36.37 56-5/8" 59-13/16" 92-1/2" 23.03 36.37 41.92(3.379) (1438) (1519) (2350) (2.140) (3.379) (3.894)


36.37 27" 28-1/2" 92-1/2" 23.03 36.37 41.92(3.379) (685) (723) (2350) (2.140) (3.379) (3.894)

6080AP/PA 41.51 64-5/8" 67-13/16" 92-1/2" 27.44 41.51 47.22(3.856) (1641) (1723) (2350) (2.549) (3.856) (4.387)


41.51 31" 32-1/2" 92-1/2" 27.44 41.51 47.22(3.856) (787) (826) (2350) (2.549) (3.856) (4.387)

400

F

renc

hwoo

d®Hi

nged

Patio

Doo

rs–O

utsw

ing

66

Frenchwood® Hinged Patio Doors - OutswingClear Opening Details Scale 1-1/2" = 1'-0" (1:8)


Support Mullion










• Consult with an architect or structural engineer regarding minimum requirements for structural support members between adjacent door rough openings.



CAUTION: In masonry wall construction, provide a minimum of 1/2" clearance from the top of the brick or masonry to the bottom of any portion of the sill. Failure to do so could result in product damage. Fill the void with closed cell foam backer rod and sealant. Be sure to allow for dimensional change of framework.


Vertical SectionHorizontal Section — Two Panel Door

Active Panel Open

Horizontal Section — Two Panel DoorActive / Passive Panels Open

3/4" (19)

Unit Dim. WidthUnit Dim. Width

2-3/4" (70)

Unit Dim. WidthUnit Dim. Width

3-3/4" (95)

2" (51)

Active Astragal


Passive


Door at 90° clear opening position

Door at full clear opening position

1-3/4" (44)

Active

Clear Opening Width 90°

Passive

Clear Opening Width Full Open Position

Door at 90° clear opening position

Door at full clear opening position

1-3/4" (44) 1-3/4" (44)

Sill

1-1/4" (32)

Clea

r Ope

ning

Hei

ght

Head

Horizontal Section — Single Panel Door

Jamb

Clear Opening Width 90°

Jamb

Clear Opening Width Full Open Position1-3/4" (44)

1-3/4" (44)

67

Colonial Modi�ed Colonial *

Prairie AShort Fractional *

Tall Fractional *

FWH 4380

FWO 4380

FWH 2780 FWH 2980FWH 3180 FWH 3380

FWO 2780 FWO 2980FWO 3180 FWO 3380

FWH 2180FWO 2180

FWG 4368 FWG43611

FWH 2768 FWH 27611FWH 2968 FWH 29611FWH 3168 FWH 31611

FWO 2768 FWO 27611FWO 2968 FWO 29611FWO 3168 FWO 31611

FWG 2968 FWG 29611FWG 3368 FWG 33611

FWH 2168 FWH 21611FWO 2168 FWO 21611


Standard Divided Light Patterns for All Frenchwood® Patio Doors

Speci�ed equal light and custom patterns are also available. For more information on Andersen divided light, see page 2-3 or visit andersenwindows.com/grilles.

Unit Number

Custom Pattern Examples

Speci�ed Equal Light Examples

400

F

renc

hwoo

d®Hi

nged

Patio

Doo

rs–O

utsw

ing

Frenchwood® Patio Door Sidelights & Transoms

68

Table of Basic Sidelight and Transom Unit Sizes Scale 1/8" = 1'-0" (1:96)

Unit Dimension

Rough Opening

Unobstructed Glass

Unobstructed Glass(2-wide units)

1'-0

13/ 1

6"

1'-1

1/ 2

"

4 3 /

8"

(325

)

(111

)

(343

)

1'-5

13/ 1

6"

1'-6

1/ 2

"

9 3 /

8"

(452

)

(238

)

(470

)

1'-9

13/ 1

6"

1'-1

0 1 /

2"

13 3

/ 8"

(554

)

(340

)

(572

)

1'-0

13/ 1

6"

1'-1

1/ 2

"

4 3 /

8"

(325

)

(111

)

(343

)

1'-5

13/ 1

6"

1'-6

1/ 2

"

9 3 /

8"

(452

)

(238

)

(470

)

1'-9

13/ 1

6"

1'-1

0 1 /

2"

13 3

/ 8"

(554

)

(340

)

(572

)

13 5/16"

2'-1"

2'-0 1/2"

(338)

(622)

(635)

18 15/16"

2'-7"

2'-6 1/8"

(481)

(765)

(787)

20 15/16"

2'-9"

2'-8 1/8"

(532)

(816)

(838)

24 15/16"

3'-1"

3'-0 1/8"

(633)

(918)

(940)

36 13/16"

4'-1"

4'-0"

(935)

(1219)

(1245)

48 1/16"

5'-0"

4'-11 1/4"

(1221)

(1505)

(1524)

52 1/16"

5'-4"

5'-3 1/4"

(1322)

(1607)

(1626)

60 1/16"

6'-0"

5'-11 1/4"

(1526)

(1810)

(1829)

10 3/8"

1'-7 1/2"

1'-6 13/16"

(264)

(478)

(495)

6 3/8"

1'-3 1/2"

1'-2 13/16"

(162)

(376)

(394)

(338) (338)

135/16" 135/16"

(481) (481)

1815/16" 1815/16"

(532) (532)

2015/16" 2015/16"

(633) (633)

2415/16" 2415/16"

FWSLT1311 FWSLT1711

FWSLT1316 FWSLT1716

FWSLT13110 FWSLT17110

6'-1

0 3 /

8"(2

092)

6'-1

1"(2

108)

66 5

/ 16"

(168

4)

6'-7

1/ 2

"(2

019)

6'-8

"(2

032)

63 7

/ 16"

(161

1)

7'-1

1 1 /

2"(2

426)

8'-0

"(2

438)

79 7

/ 16"

(201

8)

FWSL13611 FWSL17611

FWSL1368 FWSL1768

FWSL1380 FWSL1780

FWT2111 FWT2711 FWT2911 FWT3111 FWT4111 FWT5011 FWT5411 FWT6011

FWT-2-4111 FWT-2-5011 FWT-2-5411 FWT-2-6011


FWT-2-4116 FWT-2-5016 FWT-2-5416 FWT-2-6016


FWT-2-41110 FWT-2-50110 FWT-2-54110 FWT-2-60110

• Rough opening dimensions may need to be increased to allow for use of building wraps, flashing, sill panning, brackets, fasteners or other items. See page 7 for more details.

• Andersen® art glass panels are available for all units on this page.



• Combinations of door units joined together may require horizontal or vertical reinforcement. This reinforcement should be specified by a professional engineer.


69

Typical Sidelight and Transom Patio Door Combinations

Sidelight and Transom Joining Details Scale 1-1/2" = 1'-0" (1:8)

Vertical Section Transom

Horizontal Section Sidelight

FWG 60611 FWO5468 FWO4168FWT3116FWT6016 FWT-2-54110 FWSLT1316 FWSLT1316 FWSLT1716FWT-2-4116

FWSL1780FWSL1768 FWSL1768 FWSL1368 FWSL1368FWO3168

FWO3180FWT31110 FWT31110

FWO6080FWO3180 FWO3180FWT-2-60110

Over

all U

nit D

imen

sion

Hei

ght

Unit

Dim

ensi

on H

eigh

tUn

it Di

men

sion

Hei

ght

Min

imum

Rou

gh O

peni

ng H

eigh

t

Head

Head

Sill

3/4" (19)

3/4" (19)1" (25)

1" (25)


Andersen®optionaloak or maplethreshold

Overall Unit Dimension Width

Unit Dimension WidthUnit Dimension Width


3/4" (19)

3/8" (10) 3/8" (10)

1" (25)1" (25)Metro™ Collection,Tribeca® handle

Rough opening dimensions may need to be increased to allow for use of building wraps, �ashing, sill panning,

brackets, fasteners or other items. See page 7 for more details.

400

F

renc

hwoo

d®Hi

nged

Patio

Doo

rs–O

utsw

ing

Frenchwood® Door Sidelights

Unit NumberGlass Area

Sq. Ft. (m2) Overall Unit Area

Sq. Ft. (m2) FWSL 1368 2.82 (0.262) 8.18 (0.760)FWSL 1768 4.58 (0.426) 10.39 (0.965)FWSL 13611 2.95 (0.274) 8.47 (0.787)FWSL 17611 4.79 (0.445) 10.76 (1.000)FWSL 1380 3.53 (0.328) 9.82 (0.913)FWSL 1780 5.74 (0.533) 12.48 (0.159)

Frenchwood® Door Transoms Simulated Astragal



Sq. Ft. (m2) FWT-2 4111 0.82 (0.076) 4.27 (0.397)FWT-2 4116 1.74 (0.162) 5.94 (0.552)FWT-2 41110 2.49 (0.231) 7.27 (0.675)FWT-2 5011 1.16 (0.108) 5.27 (0.490)FWT-2 5016 2.48 (0.230) 7.33 (0.681)FWT-2 50110 3.53 (0.328) 8.98 (0.834)FWT-2 5411 1.28 (0.119) 5.63 (0.523)FWT-2 5416 2.74 (0.255) 7.82 (0.727)FWT-2 54110 3.91 (0.363) 9.58 (0.890)FWT-2 6011 1.53 (0.142) 6.34 (0.589)FWT-2 6016 3.26 (0.303) 8.81 (0.819)FWT-2 60110 4.65 (0.432) 10.79 (1.003)

Frenchwood® Door Sidelight Transoms



Sq. Ft. (m2) FWSLT 1311 0.20 (0.018) 1.32 (0.122)FWSLT 1316 0.42 (0.039) 1.83 (0.170)FWSLT 13110 0.60 (0.055) 2.24 (0.208)FWSLT 1711 0.32 (0.030) 1.67 (0.156)FWSLT 1716 0.68 (0.063) 2.33 (0.216)FWSLT 17110 0.97 (0.090) 2.85 (0.265)

Frenchwood® Door Transoms



Sq. Ft. (m2) FWT 2111 0.41 (0.038) 2.18 (0.203)FWT 2116 0.87 (0.081) 3.03 (0.282)FWT 21110 1.24 (0.116) 3.71 (0.345)FWT 2711 0.58 (0.054) 2.68 (0.249)FWT 2716 1.24 (0.115) 3.73 (0.346)FWT 27110 1.77 (0.164) 4.56 (0.424)FWT 2911 0.64 (0.060) 2.86 (0.266)FWT 2916 1.37 (0.127) 3.97 (0.369)FWT 29110 1.95 (0.181) 4.87 (0.452)FWT 3111 0.76 (0.071) 3.21 (0.299)FWT 3116 1.63 (0.152) 4.47 (0.415)FWT 31110 2.33 (0.216) 5.47 (0.508)FWT 4111 1.13 (0.105) 4.27 (0.397)FWT 4116 2.41 (0.224) 5.94 (0.552)FWT 41110 3.43 (0.319) 7.27 (0.675)FWT 5011 1.47 (0.137) 5.27 (0.490)FWT 5016 3.14 (0.292) 7.33 (0.681)FWT 50110 4.48 (0.416) 8.98 (0.834)FWT 5411 1.59 (0.148) 5.63 (0.523)FWT 5416 3.40 (0.316) 7.82 (0.727)FWT 54110 4.85 (0.451) 9.58 (0.890)FWT 6011 1.84 (0.171) 6.34 (0.589)FWT 6016 3.93 (0.365) 8.81 (0.819)FWT 60110 5.60 (0.520) 10.79 (1.003)

70

Combination Design

Andersen® Joining Materials and Installation Accessories

Reinforced Joining MaterialsMaterials vary depending on wind load requirements. The structural performance of any combination is only as high as the lowest structural performance of any individual unit or join in the combination.

Reinforced joining materials are used to create unit alignment, positive joining and load transfer between the Andersen units and the rough opening. These materials provide added strength capable of withstanding a variety of wind load pressures while maintaining the classic Andersen appearance. Reinforced joining materials are positioned between the jambs and fastened to the rough opening structure.

Aluminum Joining System*

The aluminum mullion/transom material is available in two lengths: 6'-0-3/32" and 7'-8". High-quality aluminum provides increased stiffness and is anodized for corrosion resistance. The aluminum joining stays within the basic jamb of the Andersen window so the interior casing can be used without extension jambs. Adjacent window units attach to the aluminum joining with screws provided in the kit. For use with casement, awning and specialty units.

NOTE: Installation clips must be used on units with impact-resistant glass.

Steel Joining System*

The steel mullion/transom material is available in three lengths: 8'-0-1/4", 9'-6" and 12'-6 ". It is treated for corrosion resistance. The steel mullion/transom attaches to adjacent units with screws provided in the kit. For use with casement, awning, double-hung and specialty windows.

NOTE: Installation clips must be used on most units with impact-resistant glass.

Laminated Veneer Lumber (LVL) Joining SystemLVL joining material is available for both windows and patio doors. 4-9/16" x 3/4" and 6-9/16" x 3/4 LVL is available for windows. All LVL joining material includes an aluminum exterior trim retainer. LVL materials are available in a variety of lengths up to 10'-0".

For successful installation that is designed to provide the required pressure performance, it is important that genuine Andersen® joining materials and installation accessories be speci�ed by the project architect or contractor.

Andersen offers several types of joining materials. Each creates a joining system that maintains the authentic look of Andersen products. The details below give a brief overview of some materials. Reinforced joining materials are recommended for use with units with impact-resistant glass. Choose the type appropriate for your combination design.

The addition of joining materials may affect the overall rough opening dimension for your combination. Refer to the appropriate product section in this guide to determine rough opening dimensions. Review complete written installation guides available from your local Andersen supplier or �nd them on our website at www.andersenwindows.com.

Exterior trim strip

Aluminum joining material

End plate

Exterior trim strip

Steel joining material

End bracket

Exterior trim strip

LVL joining material

Installation clip

*See the Andersen® Product Guide for aluminum and steel joining tables and additional reinforcing information.

Components used with each joining system kit will vary depending on units to be joined. Check with your Andersen supplier for more information. Review complete written installation guides available from your local Andersen supplier or �nd them on our website at www.andersenwindows.com.

Andersen Exterior Trim Strips - A variety of trim strips for �nishing the joint between the joined units are available in colors to match the Andersen units.Andersen Interior Wood Casing - Available in several wood types, sizes and style options including laminated arch casings and decorative plinth and key blocks.

71

A B

C

A

B

C

A B

C

A

B

C

Combination Design - Casement, Awning and Flexiframe® Windows

Aluminum Reinforced Joining MaterialE = 10 x 106 psi, I (AXIS x - x) = .59 in4

6061-T6 Aluminum

4" x 3/16" Steel Reinforced Joining MaterialE = 29 x 106 psi, I (AXIS x - x) = 1.0 in4

A36 hot rolled steel

NOTE: For a mullion joint with a continuous jamb on one side, multiply the PSF by 1.2.

For a mullion joint with a continuous jamb on both sides, multiply the PSF by 1.4.

NOTE: When exceeding 40 PSF design load, verify that the individual units meet the wind load performance criteria.

NOTE: For a mullion joint with a continuous jamb on one side, multiply the PSF by 1.2.

For a mullion joint with a continuous jamb on both sides, multiply the PSF by 1.4.

NOTE: When exceeding 40 PSF design load, verify that the individual units meet the wind load performance criteria.

NOTE: The structural performance of any combination is only as high as the lowest structural performance of any individual unit or join in the combination.

X X

X X

Design Wind Load – Use the table below if the values for aluminum reinforced joining material will provide adequate resistance to wind load.

Joining Method: Aluminum Reinforced

Type of Combination: 1-Way or 2-Way

For Combining: 400 Series Casement, 400 Series Awning, 400 Series Flexiframe® Windows

AVER

AGE

ADJA

CENT

UNI

T DIM

ENSI

ON

A + B ÷ 2 = 9' 1" 40 33 23 18

A + B ÷ 2 = 8' 6" 40 36 25 20 13

A + B ÷ 2 = 8' 1" 40 40 28 22 16

A + B ÷ 2 = 7' 6" 40 40 32 24 17

A + B ÷ 2 = 7' 1" 40 40 34 27 19 13

A + B ÷ 2 = 6' 6" 40 40 38 30 21 17

A + B ÷ 2 = 6' 1" 40 40 40 33 23 18 13

A + B ÷ 2 = 5' 6" 40 40 40 36 25 20 15

A + B ÷ 2 = 5' 1" 40 40 40 40 28 22 16 13

A + B ÷ 2 = 4' 6" 40 40 40 40 30 24 18 14

A + B ÷ 2 = 4' 1" 40 40 40 40 34 27 20 16

A + B ÷ 2 = 3' 6" 40 40 40 40 40 31 23 19 15

A + B ÷ 2 = 3' 1" 40 40 40 40 40 36 26 22 17 13

A + B ÷ 2 = 2' 6" 40 40 40 40 40 40 33 26 21 13

A + B ÷ 2 = 2' 1" 40 40 40 40 40 40 40 33 27 20

A + B ÷ 2 = 1' 6" 40 40 40 40 40 40 40 40 34 27

C = (mullion length) 3' 1'' or less

3' 6'' 4' 1'' 4' 6'' 5' 1'' 5' 6'' 6' 1'' 6' 6'' 7' 1'' 7' 8''

Design Wind Load – Examples for calculating joined unit structural performance. Use the table below if the values for steel reinforced joining material will provide adequate resistance to wind load.Joining Method: Steel Reinforced

Type of Combination: 1-Way or 2-Way


AVER

AGE

ADJA

CENT

UNI

T DIM

ENSI

ON

A + B ÷ 2 = 12' 6" 40 33 28 23 17 14

A + B ÷ 2 = 12' 1" 40 35 30 25 19 15

A + B ÷ 2 = 11' 6" 40 35 31 27 20 16

A + B ÷ 2 = 11' 1" 40 37 33 28 21 16

A + B ÷ 2 = 10' 6" 40 38 35 29 22 17

A + B ÷ 2 = 10' 1" 40 40 36 31 24 19 14

A + B ÷ 2 = 9' 6" 40 40 37 32 25 21 16 14

A + B ÷ 2 = 9' 1" 40 40 38 34 28 22 17 14

A + B ÷ 2 = 8' 6" 40 40 39 36 29 23 18 15

A + B ÷ 2 = 8' 1" 40 40 40 37 30 25 19 16 13

A + B ÷ 2 = 7' 6" 40 40 40 40 32 27 21 17 14

A + B ÷ 2 = 7' 1" 40 40 40 40 35 28 23 19 16 14

A + B ÷ 2 = 6' 6" 40 40 40 40 40 32 25 22 18 15

A + B ÷ 2 = 6' 1" 40 40 40 40 40 35 26 24 19 17 14

A + B ÷ 2 = 5' 6" 40 40 40 40 40 39 27 26 22 19 14 13

A + B ÷ 2 = 5' 1" 40 40 40 40 40 40 28 28 23 21 16 14

A + B ÷ 2 = 4' 6" 40 40 40 40 40 40 33 33 26 22 19 16 14

A + B ÷ 2 = 4' 1" 40 40 40 40 40 40 40 37 32 26 22 19 16 14

A + B ÷ 2 = 3' 6" 40 40 40 40 40 40 40 40 35 29 25 22 18 16

A + B ÷ 2 = 3' 1" 40 40 40 40 40 40 40 40 38 35 28 25 22 19

A + B ÷ 2 = 2' 6" 40 40 40 40 40 40 40 40 40 40 36 31 26 22 16 13

A + B ÷ 2 = 2' 1" 40 40 40 40 40 40 40 40 40 40 40 37 32 28 20 18

A + B ÷ 2 = 1' 6" 40 40 40 40 40 40 40 40 40 40 40 40 40 37 34 30


5' 6'' 6' 1'' 6' 6'' 7' 1'' 7' 6'' 8' 1'' 8' 6'' 9' 1'' 9' 6'' 10' 1'' 10' 6'' 11' 1'' 11' 6'' 12' 1'' 12' 6''

72

Combination Design

Joining Method: LVL Reinforced

Type of Combination: 2-Way


AVER

AGE

ADJA

CENT

UNI

T DIM

ENSI

ON

A + B ÷ 2 = 10' 1" 82 75 63 56 48 44 37 31 24

A + B ÷ 2 = 9' 6" 82 75 63 56 48 44 37 31 24

A + B ÷ 2 = 9' 1" 82 75 63 56 48 44 37 31 24

A + B ÷ 2 = 8' 6" 82 75 63 56 48 44 37 31 25

A + B ÷ 2 = 8' 1" 82 75 63 56 48 44 37 31 25

A + B ÷ 2 = 7' 6" 82 75 63 56 48 44 38 32 26

A + B ÷ 2 = 7' 1" 82 75 63 56 49 45 39 33 26

A + B ÷ 2 = 6' 6" 82 75 63 57 50 46 40 34 28

A + B ÷ 2 = 6' 1" 82 75 64 58 51 47 41 35 29

A + B ÷ 2 = 5' 6" 82 77 66 60 54 50 44 37 30

A + B ÷ 2 = 5' 1" 82 79 68 63 56 52 46 39 32

A + B ÷ 2 = 4' 6" 82 82 73 67 60 56 50 43 35

A + B ÷ 2 = 4' 1" 82 82 77 71 64 60 53 46 38

A + B ÷ 2 = 3' 6" 82 82 82 79 71 67 60 52 42

A + B ÷ 2 = 3' 1" 82 82 82 82 78 74 66 57 47

A + B ÷ 2 = 2' 6" 82 82 82 82 82 82 78 68 56

A + B ÷ 2 = 2' 1" 82 82 82 82 82 82 82 79 66

A + B ÷ 2 = 1' 6" 82 82 82 82 82 82 82 82 82


6' 6'' 7' 1'' 7' 6'' 8' 1'' 8' 6'' 9' 1'' 9' 6'' 10' 1''

4-9/16'' x 3/4'' LVL Reinforced Joining Material



• 2-way joining of units must be jobsite assembled within the rough opening.

• When using this joining material, 6-9/16" minimum wall thickness is required.

A BA

BC

C

BA

BA

CC

A B

C

A B

C





AVER

AGE

ADJA

CENT

UNI

T DIM

ENSI

ON

A + B ÷ 2 = 6' 1" 82 70

A + B ÷ 2 = 5' 6" 82 71

A + B ÷ 2 = 5' 1" 82 72

A + B ÷ 2 = 4' 6" 82 75

A + B ÷ 2 = 4' 1" 82 79

A + B ÷ 2 = 3' 6" 82 82

A + B ÷ 2 = 3' 1" 82 82

A + B ÷ 2 = 2' 6" 82 82

A + B ÷ 2 = 2' 1" 82 82

A + B ÷ 2 = 1' 6" 82 82


6' 1''




AVER

AGE

ADJA

CENT

UNI

T DIM

ENSI

ON A + B ÷ 2 = 6' 0" 65 51 41

A + B ÷ 2 = 5' 6" 70 56 45

A + B ÷ 2 = 5' 0" 70 62 50 41 34

A + B ÷ 2 = 4' 6" 70 68 55 46 38 33

A + B ÷ 2 = 4' 0" 70 70 62 51 43 37 32

A + B ÷ 2 = 3' 6" 70 70 70 59 40 42 36

A + B ÷ 2 = 3' 0" 70 70 70 69 38 49 42

A + B ÷ 2 = 2' 6" 70 70 70 70 34 59 51


4' 6'' 5' 0'' 5' 6'' 6' 0'' 6' 6'' 7' 0''

73

A B

CA

B

C



For Combining: 400 Series Woodwright® Full-Frame Double-Hung, 400 Series Tilt-Wash Double-Hung, 400 Series Picture Window, 400 Series Double-Hung Transom

AVER

AGE

ADJA

CENT

UNI

T DIM

ENSI

ON

A + B ÷ 2 = 6' 1" 82 70 62 50 40 32

A + B ÷ 2 = 5' 6" 82 71 63 51 42 33

A + B ÷ 2 = 5' 1" 82 72 64 53 43 35

A + B ÷ 2 = 4' 6" 82 75 68 56 46 38

A + B ÷ 2 = 4' 1" 82 79 71 59 49 39

A + B ÷ 2 = 3' 6" 82 82 78 65 54 44

A + B ÷ 2 = 3' 1" 82 82 82 72 59 48

A + B ÷ 2 = 2' 6" 82 82 82 82 70 57

A + B ÷ 2 = 2' 1" 82 82 82 82 81 66

A + B ÷ 2 = 1' 6" 82 82 82 82 82 82

A + B ÷ 2 = 1' 1" 82 82 82 82 82 82


6' 1'' 6' 6'' 7' 1'' 7' 6'' 8'



For Combining: 400 Series Woodwright® Full-Frame Double-Hung, 400 Series Tilt-Wash Double-Hung, 400 Series Picture Window, 400 Series Double-Hung Transom

AVER

AGE

ADJA

CENT

UNI

T DIM

ENSI

ON

A + B ÷ 2 = 10' 1" 82 75 63 56 48 44 37 31 24

A + B ÷ 2 = 9' 6" 82 75 63 56 48 44 37 31 24

A + B ÷ 2 = 9' 1" 82 75 63 56 48 44 37 31 24

A + B ÷ 2 = 8' 6" 82 75 63 56 48 44 37 31 25

A + B ÷ 2 = 8' 1" 82 75 63 56 48 44 37 31 25

A + B ÷ 2 = 7' 6" 82 75 63 56 48 44 38 32 26

A + B ÷ 2 = 7' 1" 82 75 63 56 49 45 39 33 26

A + B ÷ 2 = 6' 6" 82 75 63 57 50 46 40 34 28

A + B ÷ 2 = 6' 1" 82 75 64 58 51 47 41 35 29

A + B ÷ 2 = 5' 6" 82 77 66 60 54 50 44 37 30

A + B ÷ 2 = 5' 1" 82 79 68 63 56 52 46 39 32

A + B ÷ 2 = 4' 6" 82 82 73 67 60 56 50 43 35

A + B ÷ 2 = 4' 1" 82 82 77 71 64 60 53 46 38

A + B ÷ 2 = 3' 6" 82 82 82 79 71 67 60 52 42

A + B ÷ 2 = 3' 1" 82 82 82 82 78 74 66 57 47

A + B ÷ 2 = 2' 6" 82 82 82 82 82 82 78 68 56

A + B ÷ 2 = 2' 1" 82 82 82 82 82 82 82 79 66

A + B ÷ 2 = 1' 6" 82 82 82 82 82 82 82 82 82


6' 6'' 7' 1'' 7' 6'' 8' 1'' 8' 6'' 9' 1'' 9' 6'' 10' 1''

4 9/16'' x 3/4'' LVL Reinforced Joining Material


A B

C

C

A BA

BC



74

Combination Design - Patio Doors

A BA

C

A B BA

8'Max

8'Max

10'Max

T ab le 11

T ab le 10

T ab le 9

T ab le 11

C




Joining Method: 4-9/16" LVL Reinforced Joining System

Type of Combination: 1-Way and 2-Way

For Combining: 400 Series Frenchwood® Gliding Patio Doors, 400 Series Frenchwood® Hinged Patio Doors - Inswing, 400 Series Frenchwood® Hinged Patio Doors - Outswing, 400 Series Frenchwood® Patio Door Sidelights, 400 Series Frenchwood® Patio Door Transoms

AVER

AGE

ADJA

CENT

UNI

T DIM

ENSI

ON

A + B ÷ 2 = 8' 0" 30 27 25 23 21 20 18 17 16 15

A + B ÷ 2 = 7' 9" 31 29 26 24 22 21 19 17 16 15

A + B ÷ 2 = 7' 6" 32 29 27 25 23 21 19 18 17 15

A + B ÷ 2 = 7' 3" 33 30 27 25 23 21 20 19 17 16

A + B ÷ 2 = 7' 0" 34 31 29 24 24 22 21 19 17 16

A + B ÷ 2 = 6' 9" 35 32 29 27 25 23 21 19 18 17

A + B ÷ 2 = 6' 6" 36 33 31 28 26 24 22 20 19 17

A + B ÷ 2 = 6' 3" 37 34 31 29 27 25 23 21 19 18

A + B ÷ 2 = 6' 0" 39 35 33 30 27 25 23 22 20 19

A + B ÷ 2 = 5' 9" 40 37 34 31 29 27 25 23 21 19

A + B ÷ 2 = 5' 6" 42 38 35 33 30 27 25 23 22 20

A + B ÷ 2 = 5' 3" 43 40 37 34 31 29 27 25 23 21

A + B ÷ 2 = 5' 0" 45 42 39 35 33 30 27 25 23 22

A + B ÷ 2 = 4' 9" 47 44 40 37 34 31 29 27 25 23

A + B ÷ 2 = 4' 6" 50 46 42 39 35 33 30 28 26 24

A + B ÷ 2 = 4' 3" 53 49 45 41 37 35 32 29 27 25

A + B ÷ 2 = 4' 0" 56 51 47 43 39 37 33 31 29 27

A + B ÷ 2 = 3' 9" 59 54 50 46 52 39 35 33 30 28

A + B ÷ 2 = 3' 6" 63 57 53 49 45 41 38 35 32 30

A + B ÷ 2 = 3' 3" 67 62 57 52 48 44 41 37 33 32

A + B ÷ 2 = 3' 0" 73 67 61 56 51 47 43 40 37 34


8' 0'' 8' 3'' 8' 6'' 8' 9'' 9' 0'' 9' 3'' 9' 6'' 9' 9'' 10' 0''

Joining Method: 6-9/16" LVL Reinforced Joining System


For Combining: 400 Series Frenchwood® Gliding Patio Doors, 400 Series Frenchwood® Hinged Patio Doors - Inswing, 400 Series Frenchwood® Hinged Patio Doors - Outswing, 400 Series Frenchwood® Patio Door Sidelights, 400 Series Frenchwood® Patio Door Transoms

AVER

AGE

ADJA

CENT

UNI

T DIM

ENSI

ON

A + B ÷ 2 = 8' 0" 45 43 43 41 41 40 37 36 35 35

A + B ÷ 2 = 7' 9" 46 45 44 43 42 41 38 37 37 35

A + B ÷ 2 = 7' 6" 47 46 45 44 43 42 39 38 37 37

A + B ÷ 2 = 7' 3" 49 47 47 45 44 43 40 39 39 38

A + B ÷ 2 = 7' 0" 50 49 48 47 45 45 41 41 40 39

A + B ÷ 2 = 6' 9" 51 51 49 48 47 46 43 42 41 40

A + B ÷ 2 = 6' 6" 53 52 51 50 49 47 44 43 42 41

A + B ÷ 2 = 6' 3" 55 54 53 51 50 49 46 45 44 43

A + B ÷ 2 = 6' 0" 57 56 55 53 52 51 47 47 45 45

A + B ÷ 2 = 5' 9" 59 58 57 55 54 53 49 49 47 47

A + B ÷ 2 = 5' 6" 62 61 59 57 56 55 51 51 49 49

A + B ÷ 2 = 5' 3" 65 63 61 60 59 57 53 53 51 51

A + B ÷ 2 = 5' 0" 67 66 64 63 61 60 56 55 54 53

A + B ÷ 2 = 4' 9" 71 69 67 65 64 63 59 57 57 55

A + B ÷ 2 = 4' 6" 74 73 71 69 67 65 62 61 59 58

A + B ÷ 2 = 4' 3" 77 76 75 73 71 69 65 64 63 61

A + B ÷ 2 = 4' 0" 77 77 77 77 75 73 69 67 66 65

A + B ÷ 2 = 3' 9" 77 77 77 77 77 77 73 72 70 69

A + B ÷ 2 = 3' 6" 77 77 77 77 77 77 77 76 75 73

A + B ÷ 2 = 3' 3" 77 77 77 77 77 77 77 77 77 77

A + B ÷ 2 = 3' 0" 77 77 77 77 77 77 77 77 77 77


8' 0'' 8' 3'' 8' 6'' 8' 9'' 9' 0'' 9' 3'' 9' 6'' 9' 9'' 10' 0''

8'Max

75

PeRFoRMAnCe STAnDARDSThe Window and Door Manufacturers Association (WDMA), The American Architectural Manufac-tures Association (AAMA) and the Canadian Standards Association (CSA) have jointly released AAMA/WDMA/CSA 101/I.S. 2/A440-08; North American Fenestration Standard/Specification for Windows, Doors and Skylights, which calls for using “Performance Grade" as the new rating to describe products that comply to the standard. This new version dated “-08” has been adopted by the 2009 International Building Code (IBC) and the International Residential Code (IRC).

Performance Grade ratings are being used to replace Design Pressure Ratings as the preferred method of measuring product performance throughout the window, door and skylight industry to define products that comply with all of the requirements of the 101/I.S. 2/A440 standard.

A product only achieves a “Performance Grade” or “PG” rating if that product complies with not only the structural loading requirement, but all other performance requirements such as air infiltration resistance, water penetration resistance, ease of operation and resistance to forced entry. A “Design Pressure Rating” or “DP” rating will now describe a product rating that has only been tested to structural loading and not air infiltration, water testing or other requirements for Performance Grade.

Performance Classes

This Standard/Specification defines requirements for four performance classes. The performance classes are designated R, LC, CW, and AW. This classification system provides for several levels of performance. Product selection is always based on the performance requirements of the particular project.

Elements of Performance Grade (PG) designations

In order to qualify for a given performance grade (PG), test specimens need to pass all required performance tests for the following, in addition to all required auxiliary (durability) tests (not shown here) for the applicable product type and desired performance class: (a) Operating force (if applicable): Minimum and maximum operating force vary by product type and performance class. (b) Air leakage resistance: tested in accordance with ASTM E283 at a test pressure of 1.57 PSF. The allowable air infiltration for R, LC & CW is 0.3 cubic feet per minute per square foot of frame (cfm/ft2).(c) Water penetration resistance: tested in accordance with ASTM E547 with the specified test pressure applied per AAMA/WDMA/CSA 101/I.S.2/A440-08. The test consists of four cycles. Each cycle consists of five minutes with pressure applied and one minute with the pressure released, during which the water spray is continuously applied. The water spray shall be uniformly applied at a constant rate of 5.0 U.S. gal/ft2 • hr.(d) Uniform load deflection test: tested in accordance with ASTM E330 for both positive and negative pressure (pressure defined by AAMA/WDMA/CSA 101/I.S.2/A440-08) with the load maintained for a period of 60 seconds. After loads are removed there shall be no more permanent deformation in excess of 0.4% of its span and no damage to the unit which would make it inoperable. (e) Uniform load structural test: tested in accordance with ASTM E330 for both positive and negative pressure (pressure defined by AAMA/WDMA/CSA 101/I.S.2/A440-08) with the load maintained for a period of 10 seconds. After loads are removed there shall be no damage to the unit which would make it inoperable. (f) Forced-entry resistance (if applicable): tested in accordance with ASTM F588 (Windows), F476 (Swinging Doors) and F842 (Sliding Doors) at a performance level 10 rating.

Starting with the 2008 specification, design pressure (DP) will only represent the “uniform load deflection test.”Maximum size tested (MST)

Test size is a factor in determining compliance with this Standard/Specification. Each product type and class has a defined minimum set of requirements. The minimum test size increases with each class (i.e. R, LC, CW or AW).

Minimum Requirements

The minimum requirements to obtain a Performance Grade (PG) are listed below:

Product Performance Class

Minimum Performance Grade

(PG) (PSF)

Minimum Design Pressure

(DP) (PSF)

Minimum Structural Test Pressure (STP)*

(PSF)

Minimum Water Penetration Test Pressure (WTP)#

(PSF)Windows and DoorsR 15 15 22.5 2.90

LC 25 25 37.5 3.75

CW 30 30 45.0 4.50

AW 40 40 60.0 8.00

Optional Higher Performance Grades (PG) and corresponding test pressures (PSF)

PG20 PG25 PG30 PG35 PG40 PG45 PG50 PG55 PG60WTP 3.00 3.75 4.50 5.25 6.00 6.75 7.50 8.25 9.00

DP 20 25 30 35 40 45 50 55 60

STP 30.0 37.5 45.0 52.5 60.0 67.5 75.0 82.5 90.0

Air 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 The forced entry resistance (FER) is always a performance level 10 regardless of performance grade (PG).Operating Force — Minimum and maximum operating force varies by product type and performance class but does not change by performance grade (PG).

CeRTIFICATIonHallmark Certification

The Window and Door Manufacturers Association (WDMA) sponsored Hallmark Certification Program is designed to provide builders, architects, specifiers and consumers with an easily recognizable means of identifying products that have been manufactured in accordance with the appropriate WDMA and other referenced performance standards. Conformance is determined by periodic in-plant inspections by a third-party administrator. The inspections include auditing licensee quality control procedures and processes, and a review to confirm products are manufactured in accordance with the appropriate performance standards. Periodic testing of representative product constructions and components by a third-party testing laboratory is also required. When all of the program requirements are met, the licensee is authorized to use the WDMA Hallmark registered logo on the Certification Label as a means of identifying products.

Products successfully obtaining Hallmark Certification will be labeled with a 3-part code, which includes performance class, performance grade and maximum size tested.

Below is a sample certification label:

WINDOW AND DOOR MANUFACTURERS ASSOCIATION

www.wdma.com

400 SERIES CASEMENT WINDOWManufacturer stipulates conformance to the applicable standards

PRODUCT PERFORMANCE RATINGCLASS R(1) – PG 50(2) – SIZE TESTED 35.5 X 72.5(3)

DP+50/-65 psf (4)

TESTED TO:AAMA/WDMA/CSA 101/I.S.2/A440-05&08

(1) – Performance Class(2) – Performance Grade(3) – Size Tested(4) – Design PressureIn the example above, the performance class is an R, the performance grade (PG) is 50 PSF and the size tested is 35.5” x 72.5”. What this means to the specifier is, based on the optional higher performance grade chart, the laboratory tested air infiltration was less than 0.3 cfm/ft2 (test pressure is always 1.57 PSF and the allowable airflow is 0.3 cfm/ft2), the product tested success-fully resisted a laboratory water penetration test at a test pressure of 7.5 PSF (test pressure equals 15% of PG), the product tested successfully withstood a laboratory positive and negative structural test at a pressure of 75 PSF (test pressure equals 150% of performance grade) in both the positive and negative directions and the product tested passed the laboratory requirements for operational force and forced entry resistance. In addition to the minimum requirements of a PG 50, the tested product successfully passed a laboratory negative structural test of 97.5 PSF (test pressure equals 150% of performance grade) which yields a negative design pressure of 65 PSF. Based on this test, all products smaller in both width and height can be labeled with this product performance rating. Important

Building codes prescribe design pressures (DP) based on a variety of criteria (i.e. windspeed zone, building height, etc., therefore structural test pressures should not be used for code compliance. In the example above, a PG 50 performance grade rating, which passes a 50 PSF design pressure, should be used for determining code compliance, not the structural test pressure of 75 PSF.If you need further details about how Andersen® products perform to this standard, contact your Andersen supplier. If you need further information about the AAMA/WDMA/CSA 101/I.S.2/A440-08 standard or the Hallmark Certification Program please contact: WDMA, 401 N. Michigan Avenue, Suite 2200 Chicago, Il 60611 Phone: 312-321-6802 Web: wdma.comWhere designated, Andersen products are tested, certified and labeled to the requirements of the Hallmark Certification Program. Actual performance may vary based on variations in manufacturing, shipping, installation, environmental conditions and conditions of use.

Monolithic iMpact-Resistant GlassAndersen products with Stormwatch protection with monolithic impact-resistant glass have been tested to: Miami-Dade County test protocols TAS-201, TAS-202 and TAS-203. Test units were subjected to two impacts of an 8' 2x4 weighing 9 pounds, traveling 50 feet per second (approximately 34 mph). After being impacted the units were then subjected to 4,500 positive and 4,500 negative wind loading cycles.

* STP is 150% of the performance grade (PG) for windows and doors. # Water test pressure is 15% of the performance grade (PF).

76

Performance Dataandersen® 400 series products with stormwatch® protection Design pressure, air infiltration and sound transmission Ratings

For units with High-Performance™ Low-E4® Impact-Resistant Glass

Andersen® Product

AAMA/WDMA/CSA 101/IS2/A440-08

Performance Grade* (PG) Rating†

Sound Trans. Class (STC)^

Outdoor/Indoor Trans. Class

(OITC)^

400 Series Casement WindowClass CW-PG70

Size Tested 31.5 x 71.9 in, DP+70/-70 30 26

400 Series Awning WindowClass CW-PG60

Size Tested 59.8 x 31.5 in, DP+60/-65 30 26400 Series Casement and Awning Picture Window

Class LC-PG70 Size Tested 71.5 x 59.9 in, DP+70/-70 35 30

400 Series Tilt-Wash Double-Hung Window


400 Series Tilt-Wash Double-Hung Picture Window


400 Series Tilt-Wash Double-Hung Transom Window


400 Series Specialty WindowClass LC-PG70


400 Series Flexiframe® WindowClass LC-PG50

Size Tested 120 x 60 in, DP+50/-65 35 29

400 Series Springline™ WindowClass LC-PG50

Size Tested 120 x 60 in, DP+50/-65 N/A N/A400 Series Frenchwood® Gliding Patio Door

One Panel - FWG4380Class LC-PG50


Two Panel - FWG8080Class LC-PG50

Size Tested 95.3 x 95.5 in, DP+50/-65 31 28400 Series Frenchwood® Hinged Patio Door–Outswing

One Panel - FWO3080Class LC-PG50


Two Panel - FWO6068Class LC-PG50



Size Tested 95.3 x 95.5 in, DP+50/-65 34 29400 Series Frenchwood® Hinged Patio Door–Inswing

One Panel - FWH3168Class LC-PG50


Two Panel - FWH6068Class LC-PG50



Size Tested 95.3 x 95.5 in, DP+50/-65 34 30400 Series Frenchwood® Fixed Patio Door–Sidelight and Transom

Sidelight - 1780Class LC-PG50


Transom - 60110Class LC-PG50


† Larger or smaller units of a particular type may vary from the tested performance rating. Contact your Andersen supplier for more information.

* Performance Grade (PG) embodies air, water, structural and forced entry. DP = Design Pressure and is only applicable to the structural performance of the product.

◊ Performance varies by product size; see appropriate Florida Product Approval number for actual unit performance.

^ STC and OITC ratings given are for individual units based on independent tests and represent the entire unit. Better values may be available with other glazings. Contact your Andersen supplier for more information.

This data is accurate as of August 28, 2009. Due to ongoing product changes, updated test results, or new industry standards, this data may change. Contact your Andersen supplier for more information.

NOTE: smaller sizes within a size grid are certified at the performance rating of the largest size tested.

400 series products with pG Upgrade

For units with High-Performance™ Low-E4® Non-Impact Glass

Andersen® Product

AAMA/WDMA/CSA 101/IS2/A440-08

Performance Grade* (PG) Rating†

Sound Trans. Class (STC)^

Outdoor/Indoor Trans. Class

(OITC)^

400 Series Casement WindowClass CW-PG70


400 Series Awning WindowClass CW-PG60

Size Tested 59.8 x 31.5 in, DP+60/-60 26 21400 Series Tilt-Wash Double-Hung Window


400 Series Tilt-Wash Double-Hung Transom Window


400 Series Frenchwood® Gliding Patio Door

Two Panel - FWG8080Class LC-PG45


Four Panel - FWG160611Class LC-PG40

Size Tested 189 x 82.4 in, DP+40/-40 31 26400 Series Frenchwood® Hinged Patio Door–Outswing

One Panel - FWO3080Class LC-PG55



Size Tested 71.3 x 95.5 in, DP+55/-55 31 26400 Series Frenchwood® Hinged Patio Door–Inswing



400 series products with stormwatch® protection air infiltration and testing

For units with monolithic Impact-Resistant Glass

Andersen® ProductPerformance

Rating†◊

Sound Trans. Class

(STC)^

Outdoor/Indoor

Trans. Class (OITC)^

400 Series Casement Window DP +67/-82 34 29400 Series Awning Window DP +67/-82 34 31400 Series Casement and Awning Picture Window DP +67/-82 37 34400 Series Specialty Window DP +67/-82 37 34400 Series Flexiframe® Window DP +67/-70 36 32400 Series Springline™ Window DP +67/-71 36 32400 Series Frenchwood® Gliding Patio Door

One Panel - FWG4380 DP +50/-65 35 30Two Panel - FWG8080 DP +50/-65 31 29

400 Series Frenchwood® Hinged Patio Door–OutswingOne Panel - FWO3080 DP +65/-80 34 31

Two Panel - FWO6068 DP +65/-80 35 31

400 Series Frenchwood® Fixed Patio Door–Sidelight and Transom

Sidelight - 1780 DP +62/-77 36 33

Transom - 60110 DP +62/-77 36 34

77

center of Glass performance Data


Visible Light1 SC2 SHGC3

RHG (IP)4

Fading % RH Inside at 70º 7

Inside Surface

Glass Temp8Tuv5 Tdw-K6

Casement, Awning 71% 0.48 0.41 100 <1% 23% 53% 52°FCasement, Awning Picture 68% 0.47 0.40 96 <1% 22% 61% 56°FTilt-Wash 71% 0.48 0.41 100 <1% 23% 53% 52°FTilt-Wash Picture 70% 0.47 0.41 98 <1% 22% 57% 54°FTilt-Wash Transom 71% 0.47 0.41 97 <1% 20% 61% 56°FCircle Top,™ Elliptical Top, Circle, Oval 68% 0.47 0.40 97 <1% 22% 61% 56°FFrenchwood® Gliding Door 70% 0.47 0.41 98 <1% 22% 57% 54°FFrenchwood® Hinged Door 70% 0.47 0.41 98 <1% 22% 57% 54°FSpringline™ Window 67% 0.45 0.39 93 <1% 21% 61% 56°FFlexiframe,® Arch Window 67% 0.45 0.39 93 <1% 21% 61% 56°F

High-Performance™ Low-E4® Sun Impact-Resistant Glass


RHG (IP)4


Inside Surface



High-Performance™ Low-E4® SmartSun™ Impact-Resistant Glass


RHG (IP)4


Inside Surface



center of Glass performance Data — Monolithic impact-Resistant Glass

Monolithic Clear Laminated Impact-Resistant Glass

Visible Light1 SC2 SHGC3 RHG4

FadingTuv5 Tdw6

Casement, Awning 0.87 0.87 0.75 188 <1% 33%Casement Picture 0.85 0.83 0.72 180 <1% 33%Circle Top,™ Elliptical Top, Circle, Oval 0.85 0.83 0.72 180 <1% 33%Frenchwood® Outswing, Gliding Door 0.85 0.83 0.72 180 <1% 33%Flexiframe,® Arch, Springline™ Window 0.85 0.83 0.72 180 <1% 33%

Monolithic Gray Tinted Impact-Resistant Glass

Visible Light1 SC2 SHGC3 RHG4

FadingTuv5 Tdw6

Casement, Awning 0.43 0.68 0.59 150 <1% 17%Casement Picture 0.43 0.64 0.56 142 <1% 17%Circle Top,™ Elliptical Top, Circle, Oval 0.43 0.64 0.56 142 <1% 17%Frenchwood® Outswing, Gliding Door 0.43 0.64 0.56 142 <1% 17%Flexiframe,® Arch, Springline™ Window 0.43 0.64 0.56 142 <1% 17%

“High-Performance™ Low-E4®" (HP Low-E4®), “High-Performance™ Low-E4® Sun" (HP Low-E4® Sun) and “High-Performance™ Low-E4® SmartSun" (HP Low-E4® SmartSun) are Andersen trademarks for “Low-E" glass.

Based on NFRC testing/simulation conditions using Windows 4.1 and NFRC validated spectral data. 0°F outside temperature, 70°F inside temperature and a 15 mph wind.

1 Visible Light Transmittance measures how much light comes through the glass. The higher the value, from 0 to 1, the more daylight the glass lets in. Visible Transmittance is measured over the 380 to 760 nanometer portion of the solar spectrum.

2 Shading coefficients (SC) defines the amount of heat gain through the glass compared to a single lite of clear 1/8" (3 MM) glass.

3 Solar Heat Gain Coefficient (SHGC) defines the fraction of solar radiation admitted through the total unit both directly transmitted and absorbed and subsequently released inward. The lower the value, the less heat is transmitted through the glass.

4 Relative Heat Gain (RHG) is calculated under a different set of assumptions than thermal performance.

5 Transmission Ultraviolet Energy (TUV). The transmission of short wave energy in the 300-380 nanometer portion of the solar spectrum. The energy can cause fabric fading.

6 Transmission Damage Function (TDW). The transmission of short wave energy in the 300-600 nanometer portion of the solar spectrum. The value includes both the UV and visible light energy that can cause fabric fading. This rating has also been referred to as the Krochmann Damage Function.

7 Percent relative humidity (RH) before condensation occurs at the center of glass, taken using center of glass temperature.

8 Inside glass surface temperature is taken at the center of glass.

78

Performance Data

andersen® 400 series products with stormwatch® protection nFRc certified total Unit performance

HPIR MonolithicAndersen® Product Type HP HP Sun HP SmartSun Clear GrayCasement A Residential (Res) = 24" x 48" size

U-Factor1 0.33 0.33 0.33 0.79 0.79SHGC2 0.31 0.20 0.21 0.58 0.45

VT3 0.53 0.29 0.48 0.66 0.39Awning A Residential (Res) = 48" x 24" size

U-Factor1 0.33 0.34 0.33 0.83 0.83SHGC2 0.31 0.20 0.21 0.57 0.44

VT3 0.52 0.29 0.47 0.65 0.39Casement/Awning Picture Window A Residential (Res) = 48" x 48" size

U-Factor1 0.26 0.26 0.25 0.82 0.82SHGC2 0.34 0.21 0.23 0.59 0.45

VT3 0.57 0.32 0.51 0.70 0.35Tilt-Wash Double-Hung A Residential (Res) = 36" x 60" size

U-Factor1 0.35 0.35 0.34 0.79 0.79SHGC2 0.31 0.20 0.21 0.55 0.45

VT3 0.53 0.29 0.48 0.60 0.35Tilt-Wash Double-Hung Picture A Residential (Res) = 48" x 48" size

U-Factor1 0.33 0.33 0.32 — —SHGC2 0.33 0.20 0.22 — —

VT3 0.55 0.31 0.49 — —Tilt-Wash Double-Hung Transom A Residential (Res) = 48" x 48" size

U-Factor1 0.29 0.29 0.28 0.79 0.79SHGC2 0.31 0.20 0.21 0.58 0.47

VT3 0.54 0.30 0.48 0.67 0.34Elliptical Window A Residential (Res) = 48" x 48" size

U-Factor1 0.26 0.26 0.25 0.82 0.82SHGC2 0.34 0.21 0.23 0.59 0.45

VT3 0.57 0.32 0.51 0.70 0.35Circle Top™ Casement A Residential (Res) = 48" x 48" size

U-Factor1 0.26 0.26 0.25 0.85 0.85SHGC2 0.34 0.20 0.23 0.59 0.48

VT3 0.57 0.31 0.51 0.71 0.36Circle/Oval A Residential (Res) = 48" x 48" size

U-Factor1 0.26 0.26 0.25 0.85 0.85SHGC2 0.34 0.20 0.23 0.59 0.48

VT3 0.57 0.31 0.51 0.71 0.36Springline™ Window A Residential (Res) = 48" x 48" size

U-Factor1 0.31 0.31 0.30 0.85 0.85SHGC2 0.33 0.20 0.23 0.59 0.48

VT3 0.56 0.30 0.50 0.71 0.36Arch Window A Residential (Res) = 48" x 48" size

U-Factor1 0.28 0.28 0.27 0.83 0.83SHGC2 0.33 0.20 0.23 0.59 0.48

VT3 0.56 0.30 0.50 0.71 0.36Flexiframe® Window A Residential (Res) = 48" x 48" size

U-Factor1 0.27 0.27 0.26 0.82 0.82SHGC2 0.33 0.20 0.22 0.59 0.48

VT3 0.56 0.30 0.50 0.71 0.36Frenchwood® Hinged Patio Door - Inswing A Residential (Res) = 38" x 82" size

U-Factor1 0.32 0.33 0.32 — —SHGC2 0.24 0.15 0.16 — —

VT3 0.40 0.22 0.36 — —Frenchwood® Hinged Patio Door - Outswing A Residential (Res) = 38" x 82" size

U-Factor1 0.32 0.33 0.32 0.67 0.67SHGC2 0.24 0.16 0.17 0.41 0.32

VT3 0.40 0.22 0.36 0.48 0.24Frenchwood® Gliding Patio Door A Residential (Res) = 72" x 82" size

U-Factor1 0.33 0.33 0.32 0.71 0.71SHGC2 0.26 0.16 0.18 0.45 0.35

VT3 0.44 0.24 0.39 0.53 0.27Frenchwood® Patio Door Sidelight A Residential (Res) = 16" x 82" size

U-Factor1 0.33 0.33 0.33 0.65 0.65SHGC2 0.22 0.14 0.15 0.37 0.29

VT3 0.36 0.20 0.32 0.43 0.22Frenchwood® Patio Door Transom A Residential (Res) = 38" x 14" size

U-Factor1 0.32 0.32 0.31 0.71 0.71SHGC2 0.23 0.15 0.16 0.40 0.31

VT3 0.39 0.21 0.35 0.47 0.24

ComplianceAndersen® windows and patio doors meet or exceed the following standards:

NWWDA,-I.S.-2, W.D.M.A -I.S.-4 (NWWDA license No. 129), Hallmark certified and Miami-Dade PA 201, 202, 203 (Monolithic). Independent testing laboratories have performed all required tests on selected sizes. Compliance with these standards is confirmed by ongoing testing in Andersen laboratories. These products are covered by one or more of the following patents: D364,469; D374,087; D394,116; D394,714; D397,604; D417,831; D423,902; D431,172; D431,994; 4,999,950; 5,097,629; 5,199,243; 5,205,074; 5,243,783; 5,301,467; 5,406,768; 5,486,553; 5,497,594; 5,539,027; 5,595,409; 5,623,784; 5,653,485; 5,740,632; 5,773,138; 5,775,749; 5,827,607; 5,932,334; 6,015,611 and 6,161,881. Other patents pending.

(HPIR) High-Performance™ Low-E4® Impact-Resistant

NOTE: Units “High-Performance™" (HP Low-E4®), “High-Performance™ Low-E4® Sun" (HP Sun) and “High-Performance™ Low-E4® SmartSun" (HP SmartSun) are Andersen trademarks for “Low-E" glass.

1 U-Factor defines the amount of heat loss through the total unit in BTU/hr sq. ft2.°F. The lower the value, the less heat is lost through the entire product.

2 Solar Heat Gain Coefficient (SHGC) defines the fraction of solar radiation admitted through the total unit both directly transmitted and absorbed and subsequently released inward. The lower the value, the less heat is transmitted through the product.

3 Visible Transmittance (VT) measures how much light comes through a product (glass and frame). The higher the value, from 0 to 1, the more daylight the product lets in over the product's total unit area. Visible Transmittance is measured over the 380 to 760 nanometer portion of the solar spectrum.

This data is accurate as of August 28, 2009. Due to ongoing product changes, updated test results, or new industry standards, this data may change over time.

79

FL 1092

701608063PKU-1

This product meets Green Seal’s environmental standards governing energy efciency, heavy metals in the frame and sash materials, packaging, and consumer education materials.

G laz ing : 4 .0mm AN oute r/11.7mm LG (4 .7mm AN/4.7mm AN) innerLaminato r : Card ina l Interlayer: Dupont SentryGlasPlus (0.090 M)

AAMA/WDMA/CSA 101/I.S.2/A440-08 AAMA/WDMA/CSA 101/I.S.2/A440-05 ASTM E1886-02 & E1996-02

CLASS LC-PG50 SIZE TESTED 60" x 72"DP+50/-65

FW-C50 SIZE TESTED 60" x 72" DP+50/-65

Windzone 4, Missile Level DCycle Pressure +50/-65

CCL# 129-H-774ANDERSEN CORPORATION: 400 SERIES CASEMENT PICTURE WINDOW

Manufacturer Stipulates Conformance to the following standards.

0.26 1.5 0.34

0.57

Casement Picture WindowCPD# AND-N-054

Vinyl-Clad Wood Frame, Dual-Pane Low-E Impact Resistant Glazing with Argon

Product Type: Fixed

The National Fenestration Rating Council (NFRC) is a nonpartisan coalition of professionals whose purpose is to provide fair, accurate and credible energy performance ratings for fenestration products. NFRC's membership includes manufacturers, suppliers, designers, specifiers, utility companies, government agencies and other building industry representatives.

The Andersen Corporation is a founding member of the NFRC and continues to support its work to provide fair, accurate and credible energy performance ratings to consumers and the building industry. If you have any questions about the NFRC, its program or energy performance ratings, write them at: NFRC, 1300 Spring Street, Suite 500, Silver Spring, MD 20910, Tel: (301) 589-6372 Website: www.nfrc.org

aBoUt the laBelLook for this certification label on every window and patio door you buy. It was designed by the National Fenestration Rating Council to provide accurate information that helps you promote the energy efficiency of the homes you build. These ratings allow you - and your customers – to measure and compare the energy performance of similar products. If the product does not have this label, the NFRC has not verified its claims.

About the NFRC

U-Factor indicates how well a product prevents heat from escaping (the lower the number, the better).

Visible Transmittance refers to how much visible light comes through a product (the closer to 1.0, the more light is transmitted).

Test Standards

Florida Product Approval Number, Miami-Dade County Notice of Acceptence Number and/or Texas Department of Insurance Number (TDI)

Solar Heat Gain Coefficient measures how well a product blocks heat caused by sunlight (the lower the number, the more it will reduce air conditioning bills).

Performance Grade (PG) and Design Pressure (DP) ratings.

Impact-Resistant Glass Construction

80

Additional items excluded from this limited warranty:• Labor to replace sash or door panels, glass or other components.• Labor and other costs related to the removal and disposal of defective product.• Labor and materials to paint or stain any repaired or replaced product,

component, trim or other carpentry work that may be required. • Products not manufactured by Andersen. • Andersen does not warrant the performance of the low-maintenance exterior glass

coating on products with High-Performance™ Low-E4® glass. Performance will vary depending on environmental conditions.

• Minor warping of wood and clad wood doors. Andersen may defer actions on any claim for warping for a period of up to twelve (12) months from the date of the claim in order to permit conditioning and equalization to humidity and temperature conditions.

• Slight glass curvature, minor scratches or other imperfections in the glass that do not impair structural integrity or significantly obscure normal vision.

• Tarnish or corrosion to hardware finishes.• Stress cracks and broken glass.• Service trips to provide instruction on product use.• Applicable taxes and freight.• Special glazings. Contact us concerning the limited warranty on special glazings.• Andersen® art glass, electric window operators, retractable insect screens and bright

brass and satin nickel finishes on door hardware. Contact us or refer to the specific limited warranties for these products.

• Andersen® storm doors, Renewal® by Andersen products and KML by Andersen™ products have their own limited warranties and are not covered by this limited warranty.

For information on warranty coverage for products other than those that include impact-resistant glass, please refer to the specific limited warranties for these products. They are available from your Andersen dealer or at andersenwindows.com/warranty.

How to register your limited warrantyAndersen offers quick, easy warranty registration on our website. Just go to www.andersenwindows.com/warranty and submit your warranty information online. By registering, you will expedite any warranty service you may have in the future. In addition, you can receive product information updates, safety notices and special offers regarding new products, as well as information regarding enhancements for the windows and doors you've registered.

All warranty information is treated as highly confidential and will never be sold or traded to any person or organization outside of Andersen Corporation and the Andersen Dealer Network.

How to get help ....For further information or to make a claim within this limited warranty period, please contact the Andersen retailer/dealer who supplied you with your Andersen product. If unavailable or unknown to you, you may contact us at:

Andersen Windows, Inc. Andersen Service Center 100 Fourth Avenue North Bayport, MN 55003-1096

You may also contact us using the Customer Care section of our web site at andersenwindows.com or reach us by phone at 1-888-888-7020.

You can help us serve you faster by collecting and including the following important information:

• Description of the product such as the exterior color, unit size or inside visible glass measurements.

• Glass logo information etched in the inside corner of the glass.• Description of product concerns.• Documentation of the purchase date, if available.• Your name, address (with zip code) where the product

is installed and telephone numbers.

If the warranty period has expired or for repairs not covered by warranty, many replacement parts are available for purchase. When warranty coverage is unclear, Andersen may charge an inspection fee for any on-site product inspections. If the inspector determines the Andersen product has a defect covered by this limited warranty, the inspection fee will be waived.

FoR WinDoW anD DooR Units GlaZeDWith iMpact-Resistant Glass

Andersen® window and door units glazed with impact-resistant glass are warranted to be free from defects in manufacturing, materials and workmanship for ten (10) years from the date of purchase from the retailer/dealer. They are also warranted not to develop, under normal conditions, any material obstruction of vision resulting from manufacturing defects or as a result of premature failure of the glass or organic seal for ten (10) years from the date of purchase from the retailer/dealer. This limited warranty does not apply to special glazings, Andersen® art glass, glass that is not factory installed by Andersen, Andersen electric window operators, retractable insect screens and the finish on bright brass or satin nickel door hardware.

In the event a component fails as a result of a defect in manufacturing, materials or workmanship within the limited warranty period, Andersen, at its option, will: (1) provide replacement parts to the Andersen retailer/dealer you specify — installation labor is not included; or (2) provide a factory authorized repair to the existing component at no cost to you; or (3) refund the original purchase price or retailer's/dealer's price at the time of the original purchase, whichever is less. Such replacement parts or repairs are warranted for the remainder of the original limited warranty period.

General Conditions and Exclusions ....The limited warranty set forth in this document is the only express warranty (whether written or oral) applicable to Andersen® windows and doors glazed with impact-resistant glass, and no one is authorized to modify or expand this limited warranty. All warranty claims must be made during the applicable warranty period.

ALL IMPLIED WARRANTIES INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WILL EXPIRE WITH THE TERM OF THE 10-YEAR LIMITED WARRANTY. ANDERSEN EXCLUDES AND WILL NOT PAY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES AND ITS LIABILITY WILL IN ALL INSTANCES BE LIMITED TO REPAIR OR REPLACEMENT OR REFUND OF THE ACTUAL PURCHASE PRICE OF THE DEFECTIVE PRODUCT.

Some states do not allow the exclusion or limitation of incidental or consequential damages or limitation of the duration of an implied warranty, so the above limitations or exclusions may not apply to you.

This limited warranty is only applicable in the U.S.A. This limited warranty gives you specific legal rights, and you may also have other rights which may vary from state to state.

What is NOT covered by this limited warranty ....Product failure or damage due to improper installation or modification including:• Adjustments or corrections due to improper installation.• Failures due to product modifications or glass shading devices (e.g., glass tinting,

security systems, improper painting or staining, insulated coverings, etc.).• Units improperly assembled or improperly mulled by others. • Failure due to the application of non-Andersen hardware

(e.g., locksets, trim sets, hinges, panic hardware, closers, etc.).• Failure to properly install Andersen hardware.

Damage caused by the following:• Damage due to improper installation, maintenance or use, including use of

a non-commercial door as a main entrance or exit door for a building other than a single-family residential unit.

• Damage due to exposure to conditions beyond published performance specifications.• Damage to the product caused by water infiltration other than as a result of a defect

in manufacturing, materials or workmanship.• Damage due to condensation.• Damage to glass caused by others (e.g., brick wash, use of razor blades,

use of sealants, sanding or improper washing).• Damage caused by failing to properly seal the exposed wood portions of a product.

This includes, but is not limited to, the exposed wood on all sides of a door panel (e.g., exterior, interior, top, bottom and both sides), a door frame and wood grilles.

• Damage to metal surfaces caused by brickwash, chemicals or airborne pollutants, such as salt or acid rain.

• Damage that occurs during delivery by others.• Damage caused by accidents or acts of God.• Damage as a result of normal wear and tear.

For specific warranty information outside the United States, please contact your local distributor or write to:

Andersen CorporationInternational Division100 Fourth Avenue NorthBayport, MN 55003-1096USA

andersen Windows, inc.

Limited Warranty

Ten-Year (10)

What is NOT covered by this limited warranty – continued Damage caused by the following:• Improper installation, maintenance or use, including use of a non-commercial door as

a main entrance or exit door for a building other than a single-family residential unit. • Exposure to conditions beyond published performance specifications.• Water infiltration other than as a result of a defect in manufacturing, materials or workmanship.• Condensation.• Others (e.g., brick wash, use of razor blades, use of sealants, sanding or improper washing).• Failing to properly seal the exposed wood portions of a product. This includes, but is not

limited to, the exposed wood on all sides of a door panel (e.g., exterior, interior, top, bottom, and both sides), a door frame and wood grilles.

• Chemicals or airborne pollutants, such as salt or acid rain.• Delivery by others.• Accidents.• Acts of God.• Normal wear and tear.

Additional items excluded from this limited warranty:• Labor to replace sash or door panels, glass or other components.• Labor and other costs related to the removal and disposal of defective product.• Labor and materials to paint or stain any repaired or replaced product, component,

trim or other carpentry work that may be required. • Products not manufactured by Andersen.• Andersen does not warrant the performance of the low-maintenance

exterior glass coating on products with High-Performance™ Low-E4® glass. Performance will vary depending on environmental conditions.

• Minor warping of wood and clad-wood doors. Andersen may defer actions on any claim for warping for a period of up to twelve (12) months from the date of the claim in order to permit conditioning and equalization to humidity and temperature conditions.

• Slight glass curvature, minor scratches or other imperfections in the glass that do not impair structural integrity or significantly obscure normal vision.

• Tarnish or corrosion to hardware finishes.• Service trips to provide instruction on product use. • Applicable taxes and freight.• Special glazings. Contact us concerning the limited warranty on special glazings.• Andersen® art glass and decorative insulated art glass, impact-resistant glass, electric

window operators, retractable insect screens and bright brass and satin nickel finishes on door hardware. Contact us or refer to the specific limited warranties for these products.

• Andersen® storm doors and Renewal® by Andersen products have their own limited warranties and are not covered by this limited warranty.

How to register your Owner-To-Owner® limited warrantyAndersen offers quick, easy warranty registration on our website. Just go to www.andersenwindows.com/warranty and submit your warranty information online. By registering, you will expedite any warranty service you may have in the future. In addition, you can receive product information updates, safety notices and special offers regarding new products, as well as information regarding enhancements for the windows and doors you’ve registered. All warranty information is treated as highly confidential and will never be sold or traded to any person or organization outside of Andersen Corporation and the Andersen Dealer Network.

How to get help For further information or to make a claim within this limited warranty period, please contact the Andersen® retailer/dealer who supplied you with your Andersen® product. If unavailable or unknown to you, you may contact us at:

Andersen Windows, Inc.Andersen Service Center100 Fourth Avenue NorthBayport, MN 55003-1096

You may also contact us using the Customer Care section of our web site at andersenwindows.com or reach us by phone at 1-888-888-7020.

You can help us serve you faster by collecting and including the following important information:• Description of the product such as the exterior color, unit size or inside visible glass measurements.• Glass logo information etched in the inside corner of the glass.• Description of product concerns.• Documentation of the purchase date, if available.• Your name, address (with zip code) where the product is installed and telephone numbers.

If the limited warranty period has expired or for repairs not covered by warranty, many replacement parts are available for purchase. When warranty coverage is unclear, Andersen may charge an inspection fee for any on-site product inspection. If the inspector determines the Andersen® product has a defect covered by this limited warranty, the inspection fee will be waived.

andersen® windows and doors are warranted in two ways.

Glass Twenty (20) Year Transferable Limited WarrantyThe glass in Andersen® factory glazed window and door units (including dual-pane glass, High-Performance™ Low-E4® glass, High-Performance™ Low-E4® Sun glass, Low-E glass, patterned glass (including: obscure, pebble, fern, reed and cascade designs), Finelight™ grilles, divided light grilles and tempered versions of these glass options) is warranted to be free from defects in manufacturing, materials and workmanship for twenty (20) years from the date of purchase from the retailer/dealer. It is also warranted not to develop, under normal conditions, any material obstruction of vision resulting from manufacturing defects or as a result of premature failure of the glass or organic seal for twenty (20) years from the date of purchase from the retailer/dealer. Patterned glass (including obscure, pebble, fern, reed and cascade designs) is warranted not to develop, under normal conditions, any material change in appearance resulting from manufacturing defects or as a result of premature failure of the glass or organic seal for twenty (20) years from the date of purchase from the retailer/dealer. This limited warranty on glass does not apply to special order glazings, Andersen® art glass, insulated art glass for Andersen architectural products, impact-resistant glass or glass that is not factory installed by Andersen.

In the event a glass failure occurs as a result of a defect in manufacturing, materials or workmanship within the limited warranty period, Andersen, at its option, will: (1) provide the appropriate replacement glass product to the Andersen retailer/dealer you specify — installation labor is not included; or (2) provide a factory-authorized repair to the existing glass at no cost to you; or (3) refund the purchase price or the retailer’s/dealer’s price at the time of the original purchase, whichever is less. Such replacement or repair is warranted for the remainder of the original limited warranty period.

Components Other Than Glass Ten (10) Year Transferable Limited Warranty Non-glass portions of Andersen® windows and doors (including non-electric operators, locks, lifts, balance systems, hinges, handles, insect screens, weatherstripping, sash and frame members) are warranted to be free from defects in manufacturing, materials and workmanship for a period of ten (10) years from the date of purchase from the retailer/dealer. This limited warranty does not apply to Andersen electric window operators, retractable insect screens or finishes on bright brass and satin nickel door hardware. The non-glass portions of Andersen® architectural windows and doors with wood exteriors and commercial doors are subject to a limited warranty with a five (5) year period, but otherwise identical to the ten (10) year limited warranty described above.

In the event a component other than glass fails as a result of a defect in manufacturing, materials or workmanship within the limited warranty period, Andersen, at its option, will: (1) provide replacement parts to the Andersen retailer/dealer you specify — installation labor is not included; or (2) provide a factory-authorized repair to the existing component at no cost to you; or (3) refund the original purchase price or retailer’s/dealer’s price at the time of the original purchase, whichever is less. Such replacement parts or repairs are warranted for the remainder of the original limited warranty period.

General Conditions and ExclusionsThe limited warranty set forth in this document is the only express warranty (whether written or oral) applicable to Andersen® windows and doors, and no one is authorized to modify or expand this limited warranty. All warranty claims must be made during the applicable warranty period.

ALL IMPLIED WARRANTIES INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WILL EXPIRE WITH THE TERM OF THE 20, 10 and 5 YEAR LIMITED WARRANTY. ANDERSEN EXCLUDES AND WILL NOT PAY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES AND ITS LIABILITY WILL IN ALL INSTANCES BE LIMITED TO REPAIR OR REPLACEMENT OR REFUND OF THE ACTUAL PURCHASE PRICE OF THE DEFECTIVE PRODUCT.

Some states do not allow the exclusion or limitation of incidental or consequential damages or limitation of the duration of an implied warranty, so the above limitations or exclusions may not apply to you.

This limited warranty is only applicable in the U.S.A. (i.e. the fifty states and the District of Columbia). This limited warranty gives you specific legal rights, and you may also have other rights which may vary from state to state.

What is NOT covered by this limited warranty Product failure or damage due to improper installation or modification including:• Adjustments or corrections due to improper installation.• Failures due to product modifications or glass shading devices (e.g., glass tinting,

security systems, improper painting or staining, insulated coverings, etc.).• Units improperly assembled or improperly mulled by others. • Failure due to the application of non-Andersen hardware

(e.g., locksets, trim sets, hinges, panic hardware, closers, etc.).• Failure to properly install Andersen hardware.

For specific warranty information outside the United States, please contact your local distributor or write to:

Andersen CorporationInternational Division100 Fourth Avenue NorthBayport, MN 55003-1096, USA

andersen Windows, inc.

Limited Warranty

Windows & Doors

"Andersen" is a registered trademark of Andersen Corporation. All other marks where denoted are marks of Andersen Corporation. ® 2009 Andersen Corporation. All rights reserved. Printed and effective as of December, 2007.

“Andersen” is a registered trademark of Andersen Corporation. All other marks where denoted are marks of Andersen Corporation. © 2009 Andersen Corporation. All rights reserved. 11/09 Part #2000656

For additional information, such as the Andersen supplier nearest you, call 1-800-426-4261 and give reference #3034, or visit our website at andersenwindows.com

400

400

400

400

400

400

61

Fren

chwo

od®Hi

nged

Patio

Doo

rs–O

utsw

ing

53

Fren

chwo

od®Hi

nged

Patio

Doo

rs–I

nswi

ng4

7Fr

ench

wood

®

Glid

ing

Patio

Doo

rs3

3Sp

ecial

tyW

indo

ws2

1Tıl

t-Was

hDo

uble-

Hung

Wind

ows

9

Case

men

t&Aw

ning

Win

dows

Coastal Product Guide · Finelight™ Grilles-Between-The-Glass** Removable Interior Grille...

Documents

Transcript of Coastal Product Guide · Finelight™ Grilles-Between-The-Glass** Removable Interior Grille...