CLIC Pre-damping rings overview F. Antoniou, Y. Papaphilippou CLIC Workshop 2009.
CLIC workshop 2014
description
Transcript of CLIC workshop 2014
Title Author Date
CLIC workshop 2014RF phase and amplitude studies in CTF3
Alexey DubrovskiyCERN BE/[email protected] 06.02.20141Introduction to the studyCLIC CDR:CLIC workshop, 06.02.20142The main concern is that energy jitter generated in the Drive Beam accelerator would be transformed into beam-phase jitter during the final bunch compression. The tolerances are extremely tight: about 0.2% for the RF power and 0.05 for the RF phase are required in the Drive Beam accelerator, while a maximum variation of 0.1% for the Drive Beam bunch charge and 0.25 at 1 GHz for the Drive Beam bunch phase are allowed.Vendor: unknownCost: 1% of luminosity + development cost + production costCurrent solution: stable RF sourcesWe study:RF source implementations;Alternative solutions.Todays main topicAlexey Dubrovskiy
Klystron3a. LLRF loop3b. Detuning of penultimate cavities (not yet verified)
2a. Stable LLRF distribution, control and amplification (50-200 W)1a. Stable voltage modulator;(by A. Gobbo, D.Aguglia and F. Cabaleiro)1b. Stable triggers, timing0a. Independent fully controlled power network;(not considered yet)Levels of stabilizationCLIC workshop, 06.02.2014Pulsed HV Modulator220/400V MainsPulsed RF AmplifierLLRF
RF3
TriggersTiming4a. Beam feed-forward4b. Passive stabilization
BeamAlexey DubrovskiyRF sensitivity to the klystron voltageCLIC workshop, 06.02.2014
has been measured as the following:The RF phase sensitivity to the klystron voltage:
4The RF power sensitivity to the klystron voltage: expectedhas been measured in the range from 2.7 to 5.
Alexey DubrovskiyKlystron voltage stabilityCLIC workshop, 06.02.2014Summary
Measurement5* CLIC current requirement is 110-5Alexey Dubrovskiy
Phase-amplitude jitter correlationCLIC workshop, 06.02.2014General modelFrom driverFrom klystronTotal
Pulse-to-pulse @ a given timeMKS02Along the pulse of a given pulse* Complex normal distribution
JklyJdrv6The source of the pulse-to-pulse jitter is likely the same as the source of the along the pulse jitter. Alexey DubrovskiyPositive off-crest acceleration7CLIC workshop, 06.02.2014Minimization of normalized energy jitter:
The minimum of the normalized energy jitter is achieved at the following positive phase off-crest acceleration:HeadTailNormalized energy jitterOff-crest accelerationAlexey DubrovskiyExperiments with beam in CTF3CLIC workshop, 06.02.20148
NoNoInjector 3 GHz beamLinacBeam Position monitor: CL.BPM0502Beam Phase monitor: CL.BPR0475Beam Position monitors: CT.BPM0215, CT.BPM0285Beam Phase monitor:CL.BPR0532OffOff
~ 2 hoursOn-crest phaseInjector phaseOff
MKS05MKS06MKS15Alexey DubrovskiyExpected result CLIC workshop, 06.02.20149
The minimum beam energy and phase jitter at the injector phase of about 8 deg. MKS05 RF jitter after the RF compressor Alexey Dubrovskiy
Measured beam energy jitterCLIC workshop, 06.02.201410
CT.BPM0285: HorizontalBPM0285Similar measurementsAlexey DubrovskiyLinac on-crest phase along the pulse11CLIC workshop, 06.02.2014
Estimations from RF and beam energy jitter of the linac on-crest phase along the pulse showed similar profiles: RF phases
24-2-4Phase [deg]Time [ns]Alexey DubrovskiyLinac intensity & efficiencyCLIC workshop, 06.02.201412
BPM0215BPM0502+7 deg+7 deg+7 degAlexey DubrovskiyPassive phase stabilization in an injector13CLIC workshop, 06.02.2014Klystrons: high-voltage, short tube
MKS02MKS03Arc-ChicaneR561. Relation among MKS02, MKS03 and Chicane:2. Relation between MKS03 and off-crest acceleration phase :EnergiesThe following two relations help to suppress the beam phase jitter and to reduce the beam energy jitter at the beginning of linac, induced by modulator voltage jitters :Stabilizedbeam phaseOr in directive terms:Alexey Dubrovskiy
Simulation of the beam jitterCLIC workshop, 06.02.201414Initial bunch length rms [deg]Phase jitter rms [deg]ModelModulator voltage stabilityR56[mm] CTF35010-549.5CTF32210-549.5CLIC-like310-549.5Proposed5010-5-62.1CLIC target
Energy jitter rms [%]Initial bunch length r.m.s. [deg]Phase jitterEnergy jitterimprovementimprovementAlexey DubrovskiySummaryStay at the positive off-crest acceleration phase with the negative R56 and the beam should be stable.
Thank you for your attention!CLIC workshop, 06.02.201415Alexey Dubrovskiy