Clamping Arm
description
Transcript of Clamping Arm
![Page 1: Clamping Arm](https://reader036.fdocuments.in/reader036/viewer/2022062315/56815c2d550346895dca0a15/html5/thumbnails/1.jpg)
This is the 8’ metal bending brake we used. Since I forgot to take pictures, the pictures I use in this presentation to describe what I’m doing are from an 18” brake.
Just pretend it’s much bigger!
![Page 2: Clamping Arm](https://reader036.fdocuments.in/reader036/viewer/2022062315/56815c2d550346895dca0a15/html5/thumbnails/2.jpg)
These are the two levers you’ll use. You really need one person on each side. There is an adjustment on each side to account for material thickness.
Clamping Arm
Bending Arm
![Page 3: Clamping Arm](https://reader036.fdocuments.in/reader036/viewer/2022062315/56815c2d550346895dca0a15/html5/thumbnails/3.jpg)
A closer look. I put this picture in because it is the only other one I took. You can see the edge of the foot.
![Page 4: Clamping Arm](https://reader036.fdocuments.in/reader036/viewer/2022062315/56815c2d550346895dca0a15/html5/thumbnails/4.jpg)
If you look close you can see a piece of aluminum in there now. You can also see the foot cover we added. I always pictured the big flat side of the bending table as the part that sat flat against the piece being bent – that’s not it at all – it’s the edge
that makes the bend. I guess that’s why I’ve always had a hard time visualizing how that worked.
Foot Edge
Aluminum PieceBending Edge
Foot Cover
![Page 5: Clamping Arm](https://reader036.fdocuments.in/reader036/viewer/2022062315/56815c2d550346895dca0a15/html5/thumbnails/5.jpg)
For my next spars I’m going to do it a little differently. This is what I’d recommend: Make a template out of 3/4” plywood and MDF. Use your rib and trace the pattern
onto the template.
![Page 6: Clamping Arm](https://reader036.fdocuments.in/reader036/viewer/2022062315/56815c2d550346895dca0a15/html5/thumbnails/6.jpg)
Mark the flange on the top of your spar web (Note this piece is 7-1/2” x 3” to use as a test piece for the false spar behind the fuel tank. The top of the spar web is on the
left in this photo.)
![Page 7: Clamping Arm](https://reader036.fdocuments.in/reader036/viewer/2022062315/56815c2d550346895dca0a15/html5/thumbnails/7.jpg)
Slide you spar web into the brake leaving on the top flange side out for the first bend.
![Page 8: Clamping Arm](https://reader036.fdocuments.in/reader036/viewer/2022062315/56815c2d550346895dca0a15/html5/thumbnails/8.jpg)
Position your spar web so that you flange line is just showing under the brake foot.
![Page 9: Clamping Arm](https://reader036.fdocuments.in/reader036/viewer/2022062315/56815c2d550346895dca0a15/html5/thumbnails/9.jpg)
Rock the bending arm up and down as your work your bend in. (Note: when using an 8’ brake it will take about 10 times of the rocking action to get a full 90 degree
bend in.)
![Page 10: Clamping Arm](https://reader036.fdocuments.in/reader036/viewer/2022062315/56815c2d550346895dca0a15/html5/thumbnails/10.jpg)
Check your angle using your template (note: you can also make a small angle template out of scrap metal if you don’t make a rib template)
![Page 11: Clamping Arm](https://reader036.fdocuments.in/reader036/viewer/2022062315/56815c2d550346895dca0a15/html5/thumbnails/11.jpg)
Remove your spar web from the brake and place it flat. Position your template (or rib) so the top is tight to the top flange. Mark the bottom of your template (or rib) at
each end of the spar.
![Page 12: Clamping Arm](https://reader036.fdocuments.in/reader036/viewer/2022062315/56815c2d550346895dca0a15/html5/thumbnails/12.jpg)
Position the spar web so only the bottom flange is under the brake foot for the second bend. (Note: for the 8’ brake that I used we found that the line needed to be
just hidden, sliver showing, to properly locate the bend.)
![Page 13: Clamping Arm](https://reader036.fdocuments.in/reader036/viewer/2022062315/56815c2d550346895dca0a15/html5/thumbnails/13.jpg)
Check your angle using your template. (Note: We were able to just eyeball this bend since it’s close to a 90 degree bend)
![Page 14: Clamping Arm](https://reader036.fdocuments.in/reader036/viewer/2022062315/56815c2d550346895dca0a15/html5/thumbnails/14.jpg)
Check your spar for a tight fit using your template or actual rib.
![Page 15: Clamping Arm](https://reader036.fdocuments.in/reader036/viewer/2022062315/56815c2d550346895dca0a15/html5/thumbnails/15.jpg)
Checking the fit in the test piece with a # 12 center rib.
![Page 16: Clamping Arm](https://reader036.fdocuments.in/reader036/viewer/2022062315/56815c2d550346895dca0a15/html5/thumbnails/16.jpg)
Checking a # 6 center rib with a simulated spar capstrip.
![Page 17: Clamping Arm](https://reader036.fdocuments.in/reader036/viewer/2022062315/56815c2d550346895dca0a15/html5/thumbnails/17.jpg)
Checking template for correct size to nose rib.
![Page 18: Clamping Arm](https://reader036.fdocuments.in/reader036/viewer/2022062315/56815c2d550346895dca0a15/html5/thumbnails/18.jpg)
Checking nose rib fit to main spar test piece with simulated top skin.
![Page 19: Clamping Arm](https://reader036.fdocuments.in/reader036/viewer/2022062315/56815c2d550346895dca0a15/html5/thumbnails/19.jpg)
Checking nose rib fit to main spar test piece with simulated bottom skin.
![Page 20: Clamping Arm](https://reader036.fdocuments.in/reader036/viewer/2022062315/56815c2d550346895dca0a15/html5/thumbnails/20.jpg)
Just for kicks here’s how far my first main spar webs were off. Make sure you use a full sized rib to make your template or mark your spar bends!
![Page 21: Clamping Arm](https://reader036.fdocuments.in/reader036/viewer/2022062315/56815c2d550346895dca0a15/html5/thumbnails/21.jpg)
You can see what a bump it would leave if your spar is too big.