Civic Speaker System

7/27/2019 Civic Speaker System

1/8

2006 American Honda Motor Co., Inc. - All Rights Reserved. AII 33518-33914 (0610) 1 of08B54-SNA-1000-91

INSTALLATION

INSTRUCTIONS

Accessory Application Publications No.

Issue Date

OCT 2006

2007 CIVIC

4-DOOR

(DX, LX, EX)

BASS SPEAKER SYSTEM

ATTACHMENT

PARTS LIST

Bass Speaker System Attachment Kit(sold separately)

P/N 08B54-SNA-100

Right bracket

Left bracket

2 Washer-bolts, 6 x 16 mm

Clip nut

10 Wire ties

5 EPT sealers

Fuse seal

Oval cushion

Bass speaker system wire harness

All 33518-33914

2 Bass speakers

Bass unit

Bass Speaker System Kit (sold separately)P/N 08A54-SNA-100

Accessory users information manual


2/8

2 of 8 AII 33518-33914 (0610) 2006 American Honda Motor Co., Inc. - All Rights Reserved.

TOOLS AND SUPPLIES REQUIRED

Phillips screwdriver

Flat-tip screwdriver

10 mm and 8 mm wrenches

Shop towel

Isopropyl alcohol

Illustration of the Bass Speaker System Installedon the Vehicle

5317021H

BASSSPEAKER

BASS UNIT

INSTALLATION

Customer information: The information in thisinstallation instruction is intended for use only by

skilled technicians who have the proper tools,

equipment, and training to correctly and safely add

equipment to your vehicle. These procedures

should not be attempted by do-it-yourselfers.

1. Make sure you have the anti-theft code for the

radio, then write down the frequencies for the

preset buttons.

2. Disconnect the negative cable from the battery.

Installing the Bass Unit

3. Get the right bracket and one cushion tape.

Confirm where the cushion tapes will attach onto

the right bracket, then clean the area with

isopropyl alcohol on a shop towel.

4. Using scissors, cut a cushion tape into three

pieces A, B, and C. Discard piece C.

5. Position and install pieces A and B on the rightbracket as shown. Be sure to cover the inner

corner of the right bracket with cushion B.

5603120H

CUSHION TAPE

C(Discard).

ABA

B

A

B(Cover innercorner of rightbracket.)

RIGHTBRACKET

30 mm20 mm


3/8

2006 American Honda Motor Co., Inc. - All Rights Reserved. AII 33518-33914 (0610) 3 of

6. Clean the back of the bass unit with isopropyl

alcohol on a shop towel. Be sure to clean the

outer edge on the back of the bass unit as well.

7. Align the inner circle of the oval cushion with the

hollow edge on the back of the bass unit, then

attach the oval cushion to the bass unit.

5603132H

OVALCUSHION

BACKING

BASS UNIT

HOLLOWon back ofbass unit

8. Fold the excess part of the oval cushion around

the edge of the bass unit.

5603141H

OVAL CUSHION

(Fold down and attach.)

BASS UNIT

OVALCUSHION

9. Remove the four screws shown from the bass

unit, and secure the right and left brackets to the

bass unit with the four screws.

5222046H

LEFT BRACKET

BASSUNIT

RIGHTBRACKET

SCREWS (4)(Removeandreinstall.) (Do not

remove.)

LX, EXAdjust to the nineoclock position.

DXConfirm the fiveoclock position.

HIGH CUT AND GAINADJUSTMENTS

10. DX

Confirm that the HIGH CUT and GAIN

adjustments on the bass unit point at the fiveoclock position.

LX, EX

Adjust the HIGH CUT and GAIN adjustments on

the bass unit to the nine oclock position.

NOTE:

These settings are used with the audio/navigation

unit adjusted to factory settings. (See step 42 and

the users information.)

SCREWS (4)


4/8


17. Plug the bass speaker system wire harness 14-pin

connector into the bass unit.

14. Place the edge of the right bracket into the oval

hole. Slide the notch on the left bracket onto the

6 x 16 mm washer-bolt.

5223011H

FRONT

SPRING NUT

6 x 16 mmWASHER-BOLT

OVAL HOLE

BASS UNIT

5606010H

FRONT

14-PINCONNECTOR

TRUNK

LIGHT

BASS SPEAKERSYSTEM WIREHARNESS

5222050H

SPRINGNUT

SQUAREHOLE

FRONT

REAR SHELF


11. Open the trunk lid. Slide one spring nut onto the

square hole in the driver's side of the rear shelf.

13. Route the bass speaker system wire harness

14-pin connector through the rear shelf area.

12. Loosely install a 6 x 16 mm washer-bolt into the

spring nut.

16. Tighten the two 6 x 16 mm washer-bolts.

15. Thread the other 6 x 16 mm bolt through the rear

shelf and into the right bracket.

5223021H

FRONT

LEFT

BRACKET6 x 16 mmWASHER BOLT

REAR SHELFRIGHTBRACKET


14-PINCONNECTOR


5/8


21. Plug the vehicle 2-pin connector into the bass

speaker system wire harness 2-pin connector

(blue).

22. Route the bass speaker system wire harness

over the trunk springs.

Routing the Bass Speaker System Wire Harness

18. Remove the tape wrapped around the trunk light

harness to free the harness.

19. Using a flat-tip screwdriver wrapped with a shop

towel, remove the trunk light (two tabs), and

unplug the vehicle 2-pin connector.

20. Put the bass speaker system wire harness 2-pin

connector (blue) through the rear shelf as shown,

then reinstall the trunk light.

5224011H

BASS SPEAKER SYSTEMWIRE HARNESS 2-PINCONNECTOR (BLUE)

TRUNKLIGHT

FRONT

TRUNKSPRING

BASS UNIT

VEHICLE2-PINCONNECTOR

BASS SPEAKER SYSTEMWIRE HARNESS 2-PINCONNECTOR

23. Unplug the vehicle 2-pin connector from the high-

mount brake light, and plug the 2-pin connector

from the bass speaker system wire harness into

the high-mount brake light.

24. Route the vehicle 2-pin connector over the trunk

springs, and plug it into the bass speaker system

wire harness 2-pin connector.

25. Attach the 5A OPTION FUSE label to the fuse

case taped to the bass speaker system wireharness.

5224021H


2-PINCONNECTOR

FUSE CASE

FUSE SEAL5A OPTION FUSE

FRONT

VEHICLE 2-PINCONNECTOR

5714051H

TRUNK LIGHT

SHOPTOWEL

FLAT-TIPSCREWDRIVER


TRUNKLIGHT

FRONT

TAPE


6/8


Installing the Bass Speakers

28. Insert a flat-tip screwdriver wrapped with a shop

towel into the hole in the rear shelf, and remove

the right speaker grille (one clip, seven tabs).

Remove the left speaker grille the same way.

29. Remove the right and left speakers (one screw for

each speaker).

5224042H

CLIP

TABS (7)

SPEAKERGRILLE

REAR TRAY

SHOP TOWEL

REAR SHELF

FRONT

SPEAKERGRILLE

FLAT-TIPSCREWDRIVER

5224050H

TABSPEAKER

SCREW

FRONT

27. Unplug the right and left speaker wires from the

speakers, and plug the vehicle speaker wire 2-pin

connectors into the bass speaker system wire

harness 2-pin connectors.

26. Remove the two pieces of tape that secure the

vehicle left speaker wire.

5224032H

BASS SPEAKER SYSTEMWIRE HARNESS


FRONT


TAPE

LEFTSPEAKER

BASS SPEAKERSYSTEM WIREHARNESS2-PIN CONNECTOR


7/8


30. Install the right and left bass speakers using the

screws removed in step 29.

31. Plug the bass speaker system wire harness 2-pin

connectors into the right and left bass speakers.

5225010H

TABBASSSPEAKER

SCREW(Reused)

VEHICLEPANEL

FRONT

SQUAREHOLE

33. Using two wire ties, secure the bass speaker

system wire harness to the vehicle harness.

34. Using three wire ties, secure the bass speaker

system wire harness to the vehicle harness in the

areas shown.

Securing the Bass Speaker System Wire Harness

32. Wrap one EPT sealer around each connector in

the area shown, then secure the bass speaker

system wire harness to the vehicle harness using

two wire ties over the EPT sealers.

5225042H


WIRE TIE

VEHICLE

HARNESS

EPT SEALER

WIRE TIE

WIRE TIE

FRONT

5225052HVEHICLEHARNESS

WIRETIE

FRONTBASS SPEAKERSYSTEM WIREHARNESS

5225031H

BASS UNIT

RIGHT BASSSPEAKER

2-PINCONNECTOR

FRONT


2-PIN CONNECTOR

LEFT BASSSPEAKER


8/8


5225061H

EPT SEALER

WIRE TIE

FRONT

WIRE TIE

35. Wrap an EPT sealer around each 2-pin connector

in the areas shown, then secure the bass speaker

system wire harness to the vehicle harness with

two wire ties over the EPT sealers.

36. Using an additional wire tie, secure the bass

speaker system wire harness to the vehicle

harness in the area shown.

37. Make sure that the bass speaker system wire

harness does not interfere with the trunk springs

during closing and opening of the trunk lid.

38. Check that all wire harnesses are routed properly

and all connectors are plugged in.

39. Reconnect the negative cable to the battery.

40. Reinstall all removed parts.

41. Enter the customers radio anti-theft code, and

reset the radio station presets.

42. Be sure to set all the volume control adjustments

on the vehicle audio/navigation unit, such as

BASS, TREBLE, FAD, BALANCE and so on, asthe factory-set.

NOTE: When the battery is disconnected, the drivers

window AUTO function is disabled.

Start the engine. Push down on the drivers

window switch until the window is fully open.

Pull up on the drivers window switch to close the

window completely, then hold the switch for

2 seconds or more.

Lower and raise the drivers window to check

operation of the drivers window AUTO function.

Civic Speaker System

Documents

Transcript of Civic Speaker System