CHOPSTAR,ROLLSTAR,HILLSTAR,ROW-GUARD Universal row crop cUltivation … · 2020-06-19 · chopstar...

CHOPSTAR, ROLLSTAR, HILLSTAR, ROW-GUARDUniversal row crop cUltivation technology

HILLSTARROW-GUARD

CHOPSTARROLLSTAR

Universal row crop cUltivation technology

CHOPSTARROLLSTARHILLSTAR

ROW-GUARD

JUMBOPNEUMATICBOXP-BOX SPEED

22

3

MechanicalweeD control

PROPERLY DONE

In contrast to chemical weed control the mechanical approach does not only control weeds,but also achieves excellent results in soil aeration, nitrogen mobilization, regulation of thewater balance etc.

To be successful in the long term, however, basic agronomic considerations in all aspects ofcrop production must be made:

• Efficient primary tillage builds the basis for successful mechanical weed control.

• Seeding depth has an indirect influence on successful mechanical weed control.Blind combing enables you to destroy a big amount of weeds, whereby the best resultis achieved when the weeds are in the germinating stage. This operation shall not harmthe germinating seeds. Blind combing with the Einböck AEROSTAR between seedingand germination of the crop is only possible with an increased seeding depth.

• The crop rotation should involve a wide variety of different crops. Proper crop rotationcan help to prevent the massive appearance of problem weeds.

• Adapted nitrogen supply: excessive use of nitrogen-based fertiliser leads to a highamount of problem weeds.

• Seedbed preparation constitutes an essential precondition for the success ofmechanical weed control. Good soil maturity and seedbed preparation at the earliestpossible moment are prerequisites for any mechanical weed control. Einböck offers alarge variety of machinery for seedbed preparation.

SUCCESS FACTORS:PROPER CROP ROTATION, ADAPTEDSOIL PREPARATION AND EFFICIENT HOEING TECHNOLOGY

chopstar rollstar hillstar

ROLLSTARHILLSTAR

4

– these are the row crop cultivators withstar-like discs. These cultivators are mainly used in light soils. Thismachine is mainly used by clients who want to use it on a variety ofcrops like potato, vegetable, maize, etc.

Depending on the weeding width the machine is equipped with avariable number of hoe-stars. Height adjustable pre-loosening tines infront of the stars support the work for the following stars.

For a bigger row spacing or weeding width two pre-loosening tinesare used. As the stars can be pivoted horizontally and vertically, thesoil flow can be directed towards or away from the crop, just as smallhills can be maintained. Upon request the machine can be equippedwith crop deflector plates or hill-weeders. In case you want to usethe ROLLSTAR as a front mounted implement you need a special frontmounting support, which is available upon request.

– this is what Einböckcalls ridgers for hill-crops with large, concavediscs. These machines are used to push soil up inhill-crops. A pre-loosening tine breaks up the soiland the inclined discs transport the earth, pulleddown by erosion, up the hill again.

Due to the large smooth discs no hair roots of thecrop close to the surface are harmed. The discshave high quality, maintenance free bearings andcan be ideally adjusted in the angle. The optionalguided hill-weeder (3 sections) additionally fightsweeds.

General: -11Detailed description HILLSTAR: Page 20 and 21

General: Page 4-11Detailed description ROLLSTAR: Page 18 and 19


CHOPSTAR

5

General: Page 4-11Detailed description CHOPSTAR: Page 12 to 17

– these are the cultivators equipped with spring tines. These cultivators are mainly used inmedium to heavy soil and only for a particular crop, e.g. beet or maize. Depending on the desired working depth the tinesand sweeps can differ.

For row spacing larger than 60 cm shares and tines for greater working depths are offered. For narrow row spacing height-adjustable tines equipped with shallow working sweeps are offered. The number of tines and the width of sweeps per hoeelement depend on row distance and weeding width. Furthermore, crop deflector plates or discs to protect the small plantsin the first weeding operation are available.

On the CHOPSTAR you can turn the hoeing element by 180°. This allows you to convert a rear-mounted machine quickly toa front mounted one. Front mounted machines push the parallelograms, what results in a short construction of the rowcrop cultivator.

On the hoeing-elements a lot of different options like hilling elements, hilling sweeps, weeder tines, finger-hoes, etc. canbe mounted.

GRAIN, SOYA, BEET...

CHOPSTAR 25-59 cmMAIZE, SUNFLOWER...

CHOPSTAR 60-90 cmPUMPKIN, CAULIFLOWER, STRAWBERRY...

CHOPSTAR 91-150 cm

REIHENABSTAND:

6


Frame for a front mounted machine Frame for a rear-mounted machine with upper-link steering

RIGID

Frame for a front mounted machine,hydraulically folding

Frame for a rear-mounted machine, hydraulically foldingwith upper-link steering

HYDRAULICALLYFOLDING


7

The frame, on which the parallelogramsare mounted, is available in a rigid or a

hydraulically folding version.

The frame is the same whether youchoose a CHOPSTAR, ROLLSTAR or a HILLSTAR.

The special profile-frame used by Einböck,allows mounting of the parallelograms

through a single clamp lever.

SIMPLY ANDQUICKLY ADJUSTABLE

STRONG FRAMESFor high loaDs

Frame for a rear-mounted machine with double foldingframe for reduced transport width for large machines.

8


Upper-link steering for exact weedingeven in hilly terrain and in curves.

High-gauge wheels provide an optimalguidance of the row crop cultivator.The front wheels of the tractor are notreleased from weight.

Lower links guided on both sides providehigher stability.

With the hydraulic steering support thesteering action of the upper link steeringis increased. At the headland the cylinderalways has to be switched to the otherdirection. It is recommended for slopesover 6 %.

The working depth of the hoe elementcan be adjusted through the spindle ofthe Farmflex feeler wheel. Via the tensionspring and the adjustment bracket thedownforce of the parallelogram can beadjusted.

9


Due to agronomical, organisational or commercial reasonsmainly herbicides were used to keep weeds in check inthe past. This chemical weed control reduced costs andefforts while at the same time it helped to increase profitsand to stabilise crop yield. This resulted in the fact thattypical “cultivation crops” have turned into “spray crops”.Lately, also because of the significant disadvantages ofchemical weed control, an increased interest inmechanical weed control can be realised.The following reasons are basis for this trend:

• The appearance of difficult to control weeds that havepartially become resistant against certain groups ofpesticides

• A ban on a number of pesticides

• A drastic price increase of pesticides

• The general focus on environmental care

• The tolerance of an acceptable amount of weeds in thefield

• Improved machine range: upper-link steering for rearmounted machines, camera steering systemROW-GUARD

Mechanical weed control also has positive aspectson the soil:

• Increased aeration

• Disruption of the capillary action

• Breaking of crusts

• Conservation of soil nutrients that are often destroyedor displaced by chemical releases

• The natural soil components remain

• The natural soil microorganisms ensure balancedsoil conditions

withwell-MaintaineDrow crops

HIGHERPRODUCTIVITY

10


Depending on the number of rows, rear- mounted machines are equipped with an automatic upper-link steering.

It allows operation on slopes up to 6 %. Also in curves the cultivator will exactly follow the tractor. Since the steering is done viahigh gauge-wheels there is no need for the tractor to carry the machine. It is operated with activated automatic hitch controland freely movable lower links (approx. 7 cm each side). This ensures that the front wheels of the tractor are not released fromweighted, which gives a better manoeuvrability, especially in hilly terrain.

Because the front-view to the crops is often restricted, front mountedmachines are standard equipped with a track indicator.

Warning signs and lightsare available for an extra charge.

Lower links guided on both sidesRear-mounted machines with automatic upper-link steering including upper link(adjustable in length) and high-gauge wheelsFront mounted machines with track indicator for improved guidanceAdjustable retraction support on all parallelogramsStrong, adjustable parallelogramsFarmflex feeler wheels, ball bearings, adjustable via spindle, ø 300 mm / 100 mm wide2-component varnish, wear-resistant, elastic and non-pollutingOperating instructions

Standard equipment CHOPSTAR, ROLLSTAR and HILLSTAR

Upper-link steering system System with hydraulic steering support

11


Hoe element parallelogramon front mounted machines (only on CHOPSTAR)

• Solid frame (special pipe-profile) • Hydraulic folding machines with extra-strong triple frame

• Greasing points on all joints • Tempered joint pins (on hydraulically folding machines)

• High quality tines and sweeps • Universal parallelogram with retraction support

• Rear-mounted machines (depending on the number of rows)with automatic upper-link steering and high-gauge wheels with stripper and splash guard

• Quick adjustment of the parallelograms

• Easy vertical and horizontal adjustment of the tines

• Easy conversion from rear- to front mounting without additional costs(only possible on the standard version of CHOPSTAR row crop cultivator)

stanDarD eQUipMentCHOPSTAR, ROLLSTAR, HILLSTAR

All row crop cultivators,CHOPSTAR, ROLLSTAR or HILLSTAR, are equipped with the same,

wide parallelogram with retraction supportand Farmflex feeler wheel.

Hoe element parallelogramon rear-mounted machines

12

chopstar 25-59

Stepless adjustment of row spacing from 20 cm to 45 cm(without plant protection discs or plates)Stepless adjustment of row spacing from 37 cm to 45 cm(with plant protection discs or plates)Special-vibrotines, adjustable horizontally and verticallyParallelogram-guided crop deflector plates(adjustable in position) or crop deflector discsComplete hoe element with 2 duckfoot sweeps 140 mm,1 duckfoot sweep 160 mmHalf hoe element with 1 duckfoot sweep 140 mm,1 duckfoot sweep 160 mm

Standard equipmentCHOPSTAR 25-59 cm

Frame-profile extension for wider row spacingAdjustable weeder tines – also for working in the rowFinger hoe discs for work in between the plantsHeaping share for vibrotineHydraulical or mechanical steering support(not possible on all machines)Warning signs and lightsPneumatic intercrop-seederAngle-knives

Optional equipmentCHOPSTAR 25-59 cm

Technical data CHOPSTAR 25-59 cmType/

Working widthTransport

width in m 1Frame length

in m 1 Tines Hoe elements hp/kW Weight approx. kg with deflector platesrear front

ERS 5-rows RIGID 2.45 2.45 16 6 30/22 580 520ERS 6-rows RIGID 3.00 3.00 19 7 40/30 640 580ERS 8-rows HG 2 3.00 3.80 25 9 60/44 1,000 930ERS 9-rows HG 2 3.00 4.25 28 10 60/44 1,100 1,040ERS 12-rows HG 2 3.20 5.60 37 13 70/51 1,280 1,220ERS 15-rows HG 2 3.20 6.95 46 16 90/66 1,480 1,420ERS 18-rows HG 2, 4 4.80 8.30 55 19 130/96 1,950 -ERS 18-rows HG 3, 4 3.00 8.30 55 19 130/96 2,240 -ERS 24-rows HG 2, 4 6.70 11.00 73 25 160/118 2,550 -ERS 24-rows HG 3, 4 4.55 11.00 73 25 160/118 2,840 -Length of frame profile = row spacing x number of rows + 20 cm (transport width will change)1 for a row spacing of 45 cm2 hydraulically folding – triple frame3 hydraulically folding - double folding frame (paket-folding)4 4 high-gauge wheels instead of upper link steering

Technical Data and measurements are approximate and non-binding. We reserve the right to change construction and specification.

CHOPSTAR 25-59

13

chopstar 25-59

Hoe element CHOPSTAR 25-59 cm, complete, withdeflector discs and vibrotines for shallow operation

grain, soya, Beet…

Hoe element CHOPSTAR 25-59 cm, complete, withdeflector plates and vibrotines for shallow operation

14

chopstar 60-90

Stepless adjustment of row spacing from 60 cm to 70 cmRear tine with reinforcement spring, adjustable in heightExcellent horizontal tine adjustmentParallelogram-guided crop deflector platesor crop deflector discs (adjustable in position)

Standard equipmentCHOPSTAR 60-90 cm

Frame-profile extension for wider row spacingSpring-mounted hilling elementHeaping share for S-tineAdjustable weeder tines – for working in the rowHydraulical or mechanical steering support(not possible on all machines)Finger hoe discs for work in between the plantsShallow working vibrotines, adjustable in heightWarning signs and lightsFertilizer distributorPneumatic intercrop-seeder


Technical Data CHOPSTAR 60-90 cmType/

Working widthTransport

width in m 1Frame length

in m 1 Tines Hoe elements hp/kW Weight approx. kg with deflector platesrear front

EMS 2-rows RIGID 1.60 1.60 11 3 20/15 360 300EMS 4-rows RIGID 3.00 3.00 21 5 40/30 500 440EMS 4-rows HG 2 3.00 3.00 21 5 50/37 720 700EMS 6-rows RIGID 4.40 4.40 31 7 60/44 850 720EMS 6-rows HG 2 3.00 4.40 31 7 60/44 980 950EMS 8-rows RIGID 5.80 5.80 41 9 80/51 1,040 1,010EMS 8-rows HG 2 3.20 5.80 41 9 80/51 1,350 1,310EMS 12-rows HG 2, 4 4.80 8.60 61 13 140/103 1,800 -EMS 12-rows HG 3, 4 3.00 8.60 61 13 140/103 2,100 -

MOUNTED SWEEPS

Row spacing Front row of tinesHoe element complete / half

Middle row of tinesHoe element complete / half

Last row of tinesHoe element complete / half

60-90 cm 2 pieces / 1 piece120 mm half-duckfoot sweep

2 pieces / 1 piece105 mm duckfoot sweep

1 piece180 mm duckfoot sweep

70-74 cm 2 pieces / 1 piece120 mm half-duckfoot sweep



from 75 cm 2 pieces / 1 piece180 mm duckfoot sweep



Length of frame profile = row spacing x number of rows + 20 cm (transport width will change)1 for a row spacing of 70 cm2 hydraulically folding – triple frame3 hydraulically folding - double folding frame, folds to 3.00 m transport width (paket-folding)4 4 high-gauge wheels instead of upper link steering Technical Data and measurements are approximate and non-binding. We reserve the right to change construction and specification.

CHOPSTAR 60-90

15

chopstar 60-90

Hoe element CHOPSTAR 60-90 cmcomplete, with deflector plates

For crops that require shallow hoeing,the hoe element CHOPSTAR 60-90 cmis also avaiable with shallow workingvibrotines.

Hoe element CHOPSTAR 60-90 cmcomplete, with deflector discs

MaiZe, sUnFlower...

16

CHOPSTAR 91-150

chopstar 91-150

pUMpKin, caUliFlower, strawBerry...

Stepless adjustment of row spacing from 60 cm to 150 cmRear tine with reinforcement spring, height adjustableExcellent horizontal tine adjustmentParallelogram-guided crop deflector platesor crop deflector discs (adjustable in position)Hoe elements with duckfoot sweeps 180 mm

Standard equipmentCHOPSTAR 91-150 cm Frame-profile extension for wider row spacing

Spring-mounted hilling elementAdjustable weeder tines – also for working in the rowHydraulical or mechanical steering support(not possible on all machines)Finger hoe discs for work in between the plantsWarning signs and lights


Technical data CHOPSTAR 91-150 cm

Type/Working width Transportwidth in m 1

Frame lengthin m 1 Tines Hoe elements hp/kW Weight approx. kg with deflector plates

rear front

EKS 2-rows RIGID 3.00 2.55 20 4 40/30 480 440EKS 3-rows HG 2 3.00 4.05 30 6 60/44 880 840

1 for a row spacing of 150 cm2 hydraulically folding – triple frame

Hoe element CHOPSTAR 91-150 cmcomplete, with deflector plates


17

chopstar

inDiviDUally eQUippeDBEST CHOPSTAR TECHNOLOGY

Adjustable weeder tines for CHOPSTAR 25-59 cm andCHOPSTAR 60-90 cm: the outer tines on each element canbe exchanged, in order to push soil away from or towardsthe row.

This hilling element can bemounted instead of the rear tine ofthe CHOPSTAR 60-90 cm to maintainpotato hills.

Angle knives areavailable on request.

Depending on the row spacing the vibrotines are offeredwith 120 mm to 300 mm wide duckfoot sweeps.

The finger-hoe discs allow to work in betweenthe plants in the crop row. For the front versionadditional support wheels are required.

Heaping shares are used for hilling up the plantrows. They can be mounted on the holder of thevibrotine as well as on the S-tine.

18

rollstar

Stepless adjustment of row spacing from 30 to 70 cm(vegetable and beet 30-50 cm; maize 60-70 cm)1 height-adjustable pre-loosening tine with duckfoot sweepper hoe element on the potato or vegetable version2 height-adjustable pre-loosening tines with duckfoot sweepsper hoe element on the maize versionHoe stars mounted on angular roller bearing, individuallyremovableHoe stars made of high wear-resistant material

Standard equipment ROLLSTAR

Frame profile extension for wider row spacingHill-weeder tines for potato hillsHydraulical or mechanical steering support(not possible on all machines)Front mounting supportWarning signs and lightsFertilizer distributorPneumatic intercrop-seeder

Optional equipment ROLLSTAR


Frame lengthin m 1 Hoe elements Hoe stars hp/kW Weight approx. kg

Maize: Row spacing 60 - 70 cm, adjustable

EMR 2-rows RIGID 1.60 1.60 3 16 20/15 440EMR 4-rows RIGID 3.00 3.00 5 32 40/30 700EMR 6-rows RIGID 4.40 4.40 7 48 60/44 920EMR 6-rows HG 2 3.00 4.40 7 48 60/44 1,180EMR 8-rows HG 2 3.20 5.80 9 64 80/51 1,450

Potato: Row spacing 60 – 70 cm, adjustable

EKR 2-rows RIGID 1.60 1.60 3 8 20/15 400EKR 3-rows RIGID 2.30 2.30 4 12 30/22 490EKR 4-rows RIGID 3.00 3.00 5 16 40/30 620EKR 6-rows RIGID 4.40 4.40 7 24 60/44 800EKR 6-rows HG 2 3.00 4.40 7 24 60/44 1,060EKR 8-rows HG 2 3.20 5.80 9 32 80/51 1,290EKR 12-rows HG 3, 4 3.00 8.60 13 48 140/103 2,000

Beet, vegetable, special crops: Row spacing 30 – 45 cm, adjustable

EGR 2-rows RIGID 1.10 1.10 3 8 15/11 400EGR 3-rows RIGID 1.60 1.60 4 12 20/15 490EGR 4-rows RIGID 2.00 2.00 5 16 40/30 620EGR 5-rows RIGID 2.45 2.45 6 20 50/37 710EGR 6-rows RIGID 3.00 3.00 7 24 60/44 800EGR 7-rows HG 2 3.00 3.35 8 28 60/44 1,200EGR 8-rows HG 2 3.20 3.80 9 32 70/51 1,290EGR 12-rows HG 2, 4 3.20 5.60 13 48 80/51 1,650

Technical data ROLLSTAR

Length of frame profile = row spacing x number of rows + 20 cm (transport width will change)1 for a row spacing of 70 cm (potato, maize) respectively 45 cm (beet, vegetable)2 hydraulically folding – triple frame3 hydraulically folding - double folding frame, folds to 3.00 m transport width (paket-folding)4 4 high-gauge wheels instead of upper link steering


19

rollstar

ROLLSTAR

When the ROLLSTAR is used frontmounted, a special front mountingsupport is used. Example: ROLLSTAR Potato EKR 4-rows

The weeder tines can also coverand pull out the weeds along thepotato hills.

HOE ELEMENTSvarioUs

vegetaBle

MaiZe

potato

20

hillstar

Soil loosening tine with 180 mm sweepRow spacing stepless adjustable between 65 and 70 cmHoe element complete with 1 pce. sweep 180 mmand double discHoe element half with 1 pce. sweep 180 mmand single discHilling discs laterally adjustableExact adjustment of the angle of the discs

Standard equipment HILLSTAR

Frame-profile extension for wider row spacingGuided hill-weeder (3 sections)Hydraulical or mechanical steering-support(not possible on all models)Warning signs and lightsFertilizer distributorPneumatic intercrop-seeder

Optional equipment HILLSTAR


Frame lengthin m 1 Tines Hilling elements hp/kW Weight approx. kg

EHG 2-rows RIGID 1.60 1.60 3 3 20/15 360EHG 4-rows RIGID 3.00 3.00 5 5 40/30 500EHG 4-rows HG 2 2.80 3.00 5 5 50/37 720EHG 6-rows RIGID 4.40 4.40 7 7 60/44 850EHG 6-rows HG 2 3.00 4.40 7 7 60/44 980EHG 8-rows RIGID 5.80 5.80 9 9 80/51 1,040EHG 8-rows HG 2 3.20 5.80 9 9 80/51 1,350EHG 12-rows HG 2, 4 4.80 8.60 13 13 120/88 1,580EHG 12-rows HG 3, 4 3.00 8.60 13 13 140/103 1,800

Technical data HILLSTAR

Length of frame profile = row spacing x number of rows + 20 cm (transport width will change)1 for a row spacing of 70 cm2 hydraulically folding – triple frame3 hydraulically folding - double folding frame, folds to 3.00 m transport width (paket-folding)4 4 high-gauge wheels instead of upper link steering


21

HILLSTAR

hillstar

Guided hill-weeder (3-sections)

eFFicientHILLING OPERATION

22

row-gUarD

technical highlights

Sideshift frame with offset of 500 mm in totalUpper- and lower links guided on both sidesUpper- and lower links equipped with hardened bushingsQuick couplers for easy and quick attachment of the hoeGuidance shaft made from high-strength,coated metal for minimized wear and tearCamera with 2 lenses with different exposure for improvedoperation in changing light conditionsHolder for camera for Einböck hoesWheel sensor with holder and connection cable suitable forfarmflex wheels of Einböck hoesSensor on the upper link to determine the positionof the 3 point linkageControl unit with universal holder for the tractor cabinParking supportStorage box for camera and control unit1 single acting hydraulic valve with pressure-free return lineand 12 V power plug necessaryOperating instructions

Standard equipment ROW-GUARD

Xenon-working light for operation during nightStabilising discs – recommended forsmall tractors (upon request)Extension cable for cameraExtension cable for wheel sensorAdditional wheel sensor with holder for additional hoesAdditional holder for camera for additional hoesGround wheel with sensor – necessary for other brand hoes

Optional equipment ROW-GUARD

- Quick couplers on the lower links simplifymounting of the hoe

- Lower- and upper links are equippedwith hardened bushings

- Big offset of total 500 mm –corrects even serious aberration from the path

- Solid holder for camera with quick couplers to adjustthe position and the angle of the camera without tools

The steering system preciselyrecognises green crop in rows.

Easy, operator-friendly adjustment of thesystem to the different crop rows.

The big field of vision over several rows ensures goodguidance also in fields with high weed pressure.

The two lenses of the camera have different exposure settings,what minimizes the influence of shade (also in strong sunlight).

23

ROW-GUARD

row-gUarD

PRECISION CAMERA STEERINGeXactly in Between the rows

The camera steering system ROW-GUARD guides hoes absolutely precisely, even in high speed. Via a controlunit in the tractor’s cabin the precision guidance system can be adjusted very comfortably. The picture thecamera captures is being analyzed on spots with a high concentration of green pixel. With help of the availableinformation about row-configuration of the crop (row spacing, number of rows, etc.) a raster is put on top ofthe picture. This data builds the basis for the information provided to the sideshift frame which guides the hoeexactly in between the rows.

All the advantages of the ROW-GUARD system are obvious:

- improved working accuracy- working of the full area in combination with a finger weeder and- extremely efficient weed control.

Extremely high working speed (up to 15 km/h, depending on field conditions)are possible.

The operator does not get tired so quickly, the required concentration is limitedto stay in between the rows – the exact steering is done by the ROW-GUARDsteering system.

The system can be used in various different green crops, independently fromrow spacing, number of rows, etc.

24

JUMBo

1500 litres tank volumeSeeding unit made from stainless steel - paintedHydraulic fan (1 single acting hydraulic valve with up to30 l/min capacity and pressure free return line with¾“ coupling necessary)Big ground drive wheel with hydr. lifting cylinder(1 single acting valve necessary)Stepless gearbox for quantity regulationDisconnectable agitation shaftUp to 4 dosing unitsCalibration panOperating instructions

Standard equipment front-tank JUMBO

Rotary airlock(necessary for seed transportation more than 10 m)Hydr. hose set(when the tractor has hydr. valves only at the rear)Lightning

Optional equipment front-tank JUMBO

The seeding roller is driven by a bigground wheel and therefore thedistribution rate is always adjusted tothe working speed.

The quantity regulation is done stepless via a lever.

The two with the machine supplied seeding rollers allow distribution ofnearly every seed or fertilizer (independent from the size).

The hydraulic fan produces the necessary airstream to transport the fertilizer or the seeds from the seedingunit to the rear mounted distribution heads and further on to the outlets.

From a transport distance of the seeds of 10 m the optionally available rotary airlock ensures that the airstreamdoes not escape via the seeding unit and that the necessary air pressure is available.

Technical data JUMBO

Type Rotary Airlock Weight approx. kg Transport way

JUMBO OZ without 450 up to 10 mJUMBO MZ with 460 more than 10 m


pp

p

25

JUMBO

JUMBo

The front-tank JUMBO gives the opportunity to distribute seeds or fertilizer when workingwith folding hoes – in combination with an improved weight distribution!

The tank has a volume of 1500 litres and can work in combination not only with variousdifferent rear mounted hoes, but also with various different types of rear mounted machines.

FULL VOLUMEFor increaseD proDUctivity

26

PNEUMATICBOXP-BOX SPEED

pneUMaticBoX p-BoX speeDpneUMaticBoX p-BoX speeD

For the distribution of seeds (or fertilizer) you can mount ourpneumatic seeding boxes PNEUMATICBOX and P-BOX SPEED.

Further information you can find in our leaflet for the seeding boxes!

For rigid CHOPSTAR 60-90 cm, ROLLSTAR Maizeor HILLSTAR mechanical fertilizer distributorsmade from stainless steel are available.

27

• Row spacing

• Number of rows on the drill you used in the particular field

• Front- or rear mounting of the hoe (or rear mountingin combination with the camera steering system ROW-GUARD)

• Hoeing width per section(this gives the strip width next to the crop, which is not worked)

• In special crops – how deep the hoe shall work?

• Are the rows centralised between the tractor wheels?

• Hitch category of the tractor

• Track width of the tractor

We can produce a hoe for nearly all row crops for you.But we need following information:

tUneD to yoUr reQUireMentsINDIVIDUAL SOLUTIONS

Tel: (+43) 7764 64660Fax: (+43) 7764 6466-385

[email protected]

Einböck GmbH & CoKGSchatzdorf 7

A-4751 Dorf / PramAUSTRIA

kbo

1334

52FS

·11/

13·1

.000

E

CHOPSTAR,ROLLSTAR,HILLSTAR,ROW-GUARD Universal row crop cUltivation … · 2020-06-19 · chopstar...

Documents

Transcript of CHOPSTAR,ROLLSTAR,HILLSTAR,ROW-GUARD Universal row crop cUltivation … · 2020-06-19 · chopstar...