Chemistry and Light Vehicles 2012
-
Upload
abhishek-shetty -
Category
Documents
-
view
215 -
download
0
Transcript of Chemistry and Light Vehicles 2012
-
7/30/2019 Chemistry and Light Vehicles 2012
1/19
Chemistry and Light Vehicles
Economics & Statistics Department
American Chemistry Council
August 2012
-
7/30/2019 Chemistry and Light Vehicles 2012
2/19
1 | P a g e
Executive SummaryThe $142 billion light vehicle industry represents an important sector of the US economy and a large
end-use customer market for chemistry. In 2011, the 10.57 million light vehicles assembled in the
United States and Canada required some $38.4 billion in chemistry (chemical products and chemical
processing), or $3,636 of chemistry in every vehicle. This is up significantly from $2,444 in 2006 and
$1,740 in 2001.
The latest data indicate that the average weight of North American light vehicles continues to rise. The
use of plastics and composites in light vehicles continues to rise as well, reaching 377 pounds per
vehicle in 2011. In addition to plastics and composites, the typical light vehicle also utilizes 222 pounds
of rubber and 48 pounds of man-made fibers. The latter are primarily synthetic fibers. The typical
North American light vehicle also featured 34 pounds of coatings (dry weight) in 2011.
This years report on Chemistry and Light Vehicles includes an analysis of the energy savings arising
from the use of chemistry in light vehicles. The products of the business of chemistry (plastic resins,
catalysts, etc.) to a very large degree help the light vehicle industry and consumers save energy and
ultimately reduce greenhouse gas emissions. Chemistry has played a leading role in improving fuel
efficiency. For example, the average fuel efficiency (as measured in miles per gallon, or MPG) for model
2011 vehicles was 22.8 MPG1. If it werent for chemistry -- in particular, the use of plastics resins and
composites in light-weighting average fuel efficiency would be much lower perhaps as low as only
16.2 MPG.
The use of gasoline by light vehicles amounted to 15.62 quadrillion British thermal units (BTUs), or
15.62 quads in 2011. The energy savings of 2.26 to 4.40 quads is the equivalent of 1.1-2.1 million
barrels of oil per day. In other words, in absence of the benefits of chemistry, energy consumption by
light vehicles would be 14.4%-28.2% above their current levels. Most of the energy savings arose from
weight reduction and improved fuel efficiency from light-weighting efforts. Other areas where
chemistry has improved fuel efficiency include better performing oil and fuel additives, advancedcatalysis, and greater rolling resistance through advances in elastomer chemistry among other
applications.
1Source: Environmental Protection Agency
-
7/30/2019 Chemistry and Light Vehicles 2012
3/19
2 | P a g e
IntroductionThis report presents the latest results of an assessment of the chemistry and other materials make-up
of light vehicles, a major end-use customer for American chemistry. With 10.57 million light vehicles
assembled in the United States and Canada during 2011, this important market represents the
equivalent of some $38.4 billion in chemistry. This chemistry value is up from $30.7 billion in 2011
when 9.68 million units were assembled and from the depths of the recession in 2009, when 6.94
million units were assembled and the associated chemistry value was $20.7 billion. Chemistry valuelast peaked at $34.8 billion in 2007 (when 13.08 million units were assembled).
This report also features an assessment of how chemistry plays a role in fostering energy efficiency in
light vehicles. These energy savings are quantified and presented herein.
Chemistry and Light VehiclesThe light vehicle industry represents a large share of the US economy, totaling more than $142 billion
in shipments (at the manufacturers level) in 2011 and employing over 630,000 workers. The light
vehicle industry continues to be an important customer for most manufacturing industries, including
the chemical industry. This relationship is particularly strong in basic and specialty chemicals becauseevery light vehicle produced in the United States and Canada contains $3,636 of chemistry (chemical
products and chemical processing). The chemistry value per vehicle has grown considerably. Its up
14.6% from $3,174 per vehicle in 2011 and has grown 109.0% since 2001 when it was $1,740 per
vehicle. Included in the chemistry value, for example, are antifreeze and other fluids, catalysts, plastic
dash-boards and other components, rubber tires and hoses, upholstery fibers, coatings and adhesives.
Virtually every component of a light vehicle, from the front bumper to the rear tail-lights features
some chemistry.
Figure 1
Average Value of Direct Chemistry Content of North American Light Vehicles in 2011 ($/vehicle)
$0 $100 $200 $300 $400 $500 $600
Adhesives & Sealants
Carbon Black
Catalysts
Coatings
Man-Made Fibers
Plastic Resins
Plastic Additives
Plastics Compounding
Rubber Processing Chemicals
Synthetic Fluids & Additives
Synthetic Rubber
-
7/30/2019 Chemistry and Light Vehicles 2012
4/19
3 | P a g e
The average values of direct chemistry content in North American light vehicles in 2011 for a variety of
segments of the business of chemistry are presented in Figure 1 (measured in dollars per vehicle). Only
the direct chemistry value of materials is presented (the chemistry value from processing and other
indirect chemistry is not displayed).
Table 1Average Value of Chemistry Content of North American Light Vehicles ($/vehicle)
2001 2002 2003 2004 2005 2006 2007 2008 2009 2010 2011
Adhesives & Sealants $53 $55 $58 $62 $65 $71 $74 $78 $82 $84 $90
Carbon Black 24 26 27 34 41 50 53 74 89 102 107
Catalysts 103 104 108 111 100 128 132 138 140 148 164
Coatings 117 110 104 123 130 131 140 143 163 168 177
Man-Made Fibers 73 75 78 92 95 98 95 100 103 102 97
Plastic Resins 226 232 248 287 312 335 355 395 381 428 495
Plastic Additives 17 17 17 18 17 18 20 22 21 23 27
Plastics Compounding 36 37 39 40 39 43 48 53 51 57 67Rubber Processing Chemicals 14 15 15 16 18 21 22 27 28 31 42
Synthetic Fluids & Additives 56 62 67 69 79 99 108 136 135 139 168
Synthetic Rubber 176 169 185 204 235 264 280 336 349 395 530
Materials $896 $901 $947 $1,057 $1,131 $1,260 $1,327 $1,502 $1,541 $1,676 $1,964
Processing/Other Chemistry $844 $813 $886 $945 $1,088 $1,184 $1,336 $1,471 $1,443 $1,498 $1,672
Total Chemistry Content $1,740 $1,714 $1,833 $2,002 $2,219 $2,444 $2,663 $2,973 $2,984 $3,174 $3,636
The direct chemistry value during 2011 averaged $1,964 per vehicle, 54% of the total chemistry value.
Details on chemistry used are presented in Table 1. The remaining 46% (or $1,672 per vehicle) wasfrom processing and other indirect chemistry (for example, glass manufacture uses soda ash and other
processing chemicals).
Materials and Light VehiclesThe light vehicle industry is an important customer for a number of metal and other materials
manufacturing industries. For plastics and composites in particular there is significant competition with
other materials, especially aluminum and steel.
In 2011, average vehicle weight increased by 0.3% (14 pounds) to 4,072 pounds. Average vehicle
weight has risen for the past two years following two years of declines. In 1990, average vehicle weightwas 3,425 pounds. In 2000, the average vehicle weight was 3,919 pounds. The rising popularity of SUVs
was a contributing factor in rising vehicle weight during the 1990s and for most of the last decade.
Higher gasoline prices in 2008, however, prompted a reversal of this trend, and in 2009 the average
vehicle weight was at its lowest since 1999. An economic recovery and renewed popularity of larger
vehicles fostered the 2010 and 2011 increases in weight.
-
7/30/2019 Chemistry and Light Vehicles 2012
5/19
4 | P a g e
Table 2
Average Materials Content of North American Light Vehicles (pound/vehicle)
2001 2002 2003 2004 2005 2006 2007 2008 2009 2010 2011
Average Weight 3,914 3,934 3,965 4,041 4,040 4,068 4,097 4,033 3,922 4,058 4,072
Regular Steel 1,652 1,649 1,646 1,650 1,634 1,622 1,644 1,627 1,501 1,542 1,458
High- & Medium-Strength 424 443 460 479 491 502 518 523 524 559 608
Stainless Steel 63 64 65 70 71 73 75 75 69 73 73
Other Steels 28 30 32 34 35 34 34 33 31 33 32
Iron Castings 384 355 336 331 328 331 322 253 206 240 275
Aluminum 279 289 299 311 316 323 319 316 324 344 355
Magnesium 10 9 10 10 10 10 10 11 11 11 12
Copper and Brass 66 69 70 71 71 67 66 64 65 65 67
Lead 37 35 35 37 38 39 41 44 42 41 41
Zinc Castings 11 10 10 10 10 10 9 9 9 9 9
Powder Metal 38 39 41 43 42 42 43 43 41 41 41
Other Metals 4 4 4 5 4 5 5 5 5 5 5
Plastics/Composites 298 307 319 338 334 341 338 347 369 371 377Rubber 163 168 169 172 179 187 188 200 235 228 222
Coatings 26 26 25 28 27 29 29 30 34 34 34
Textiles 45 45 46 51 49 47 46 48 57 56 48
Fluids and Lubricants 208 209 210 210 210 211 215 214 217 219 223
Glass 104 104 105 105 104 105 103 99 93 95 98
Other 75 79 83 86 87 89 92 91 90 92 94
As a Percent of Total Weight 100.0% 100.0% 100.0% 100.0% 100.0% 100.0% 100.0% 100.0% 100.0% 100.0% 100.0%
Regular Steel 42.2% 41.9% 41.5% 40.8% 40.4% 39.9% 40.1% 40.3% 38.3% 38.0% 35.8%
High- & Medium-Strength 10.8% 11.3% 11.6% 11.9% 12.2% 12.3% 12.6% 13.0% 13.4% 13.8% 14.9%
Stainless Steel 1.6% 1.6% 1.6% 1.7% 1.8% 1.8% 1.8% 1.9% 1.8% 1.8% 1.8%
Other Steels 0.7% 0.8% 0.8% 0.8% 0.9% 0.8% 0.8% 0.8% 0.8% 0.8% 0.8%
Iron Castings 9.8% 9.0% 8.5% 8.2% 8.1% 8.1% 7.9% 6.3% 5.3% 5.9% 6.8%
Aluminum 7.1% 7.3% 7.5% 7.7% 7.8% 7.9% 7.8% 7.8% 8.3% 8.5% 8.7%
Magnesium 0.2% 0.2% 0.2% 0.3% 0.3% 0.3% 0.3% 0.3% 0.3% 0.3% 0.3%
Copper and Brass 1.7% 1.7% 1.8% 1.8% 1.8% 1.6% 1.6% 1.6% 1.6% 1.6% 1.6%
Lead 0.9% 0.9% 0.9% 0.9% 0.9% 1.0% 1.0% 1.1% 1.1% 1.0% 1.0%
Zinc Castings 0.3% 0.3% 0.3% 0.2% 0.2% 0.2% 0.2% 0.2% 0.2% 0.2% 0.2%
Powder Metal 1.0% 1.0% 1.0% 1.1% 1.0% 1.0% 1.0% 1.1% 1.0% 1.0% 1.0%
Other Metals 0.1% 0.1% 0.1% 0.1% 0.1% 0.1% 0.1% 0.1% 0.1% 0.1% 0.1%
Plastics/Composites 7.6% 7.8% 8.0% 8.4% 8.3% 8.4% 8.2% 8.6% 9.4% 9.2% 9.2%Rubber 4.2% 4.3% 4.3% 4.3% 4.4% 4.6% 4.6% 5.0% 6.0% 5.6% 5.5%
Coatings 0.7% 0.7% 0.6% 0.7% 0.7% 0.7% 0.7% 0.7% 0.9% 0.8% 0.8%
Textiles 1.1% 1.2% 1.2% 1.3% 1.2% 1.2% 1.1% 1.2% 1.5% 1.4% 1.2%
Fluids and Lubricants 5.3% 5.3% 5.3% 5.2% 5.2% 5.2% 5.2% 5.3% 5.5% 5.4% 5.5%
Glass 2.7% 2.6% 2.6% 2.6% 2.6% 2.6% 2.5% 2.5% 2.4% 2.3% 2.4%
Other 1.9% 2.0% 2.1% 2.1% 2.2% 2.2% 2.2% 2.3% 2.3% 2.3% 2.3%
-
7/30/2019 Chemistry and Light Vehicles 2012
6/19
5 | P a g e
The performance of vehicles has improved significantly over the years. According to EPA data, for
example, the average horsepower (HP) of model 2011 vehicles was 228 HP, compared to 181 HP in
2000 and 135 HP in 1990. Top speed now averages about 140 miles per hour (MPH) compared to 129
MPH in 2000 and only 117 MPH in 1990.
Regular steel and high- and medium-strength steel are the dominant materials in light vehicles.
Combined, this steel accounts for nearly 51% of vehicle weight. High- and medium-strength steel havebeen gaining share away from regular steel. Other steel and iron castings have generally lost share.
Combined, all iron and steel accounted for over 60% of average vehicle weight, down from 65% in
2000 and 70% in 1990.
Over the last several decades, lightweight materials have gained share away from iron and steel. For
example, aluminum gained share in 2011, rising 3.2% (or 11 pounds) to 355 pounds per vehicle.
Aluminum use represented 8.7% of average vehicle weight, up from 6.9% in 2000 and 4.7% in 1990.
Other lightweight materials such as magnesium and plastics and composites have also gained market
share away from iron castings, steel, lead, and other heavier materials. Details on materials used are
presented in Table 2. Additional metals include copper and brass, lead, and zinc, and others in both
powder and solid form. Glass, rubber, coatings, textiles, fluids and lubricants, and other materials
round out the composition of a typical light vehicle.
Plastics and Light VehiclesLight vehicles represent an important market for plastic resins and composites, one that has grown
significantly during the last five decades. The average light vehicle now contains 377 pounds of plastics
and composites, 9.2% of the total weight. This is up from 286 pounds in 2000 and 194 pounds in 1990.
In 1960, less than 20 pounds were used.
Composites are any combination of polymer matrix and fibrous reinforcement. Glass, carbon, aramid,and other fibers provide strength and stiffness while the polymer matrix (or resin) of polyester,
polyurethane, epoxy, polypropylene, nylon, or other resin protects and transfers loads between fibers.
This creates a material with attributes superior to polymer or fiber alone.
Figure 2
Long-Term Trends in Light Vehicle Plastics/Composites Use (pounds/vehicle)
0
100
200
300
400
1960 1965 1970 1975 1980 1985 1990 1995 2000 2005 2010
-
7/30/2019 Chemistry and Light Vehicles 2012
7/19
6 | P a g e
Plastic resins and composites have been essential to a wide range of safety and performance
breakthroughs in todays cars, minivans, pickups and SUVs. Todays plastics typically make up 50% of
the volume of a new light vehicle but less than 10% of its weight, which helps make cars lighter and
more fuel efficient, resulting in lower greenhouse gas emissions. Tough, modern plastics also help
improve passenger safety and automotive designers rely on the versatility of plastics when designing
todays vehicles.
Automotive Body Exterior - Plastics and composites have revolutionized the design of bodyexteriors. From bumpers to door panels, light weight plastic provides vehicles with better gas
mileage and allows designers and engineers the freedom to create innovative concepts that
otherwise would be impossible. In the past, metals were synonymous with auto body exterior
design and manufacturing. However, they are susceptible to dents, dings, stone chips and
corrosion. They are also heavier and more expensive than plastics. Specifying plastics and
composites for automotive body exterior panels and parts allows manufacturers to adopt
modular assembly practices, lower production costs, improve energy management, achieve
better dent resistance, and use advanced styling techniques for sleeker, more aerodynamic
exteriors.
Automotive Interior - The elements of automotive interior design -- comfort, noise level,aesthetic appeal, ergonomic layout, and durability -- have a great effect on a consumer's
purchasing decision. Plastic automotive interior parts address all of these aspects, and more, in
a remarkably effective and efficient manner.
Automotive Safety - The versatility of plastics allows design options that reduce vehicle weightwhile producing safer vehicles. Included are composite drive shafts that increase torque andhelp prevent injuries, plastic composite structures in the front end of a vehicle that reduce
vehicle weight without compromising safety, and plastic components in crumple zones that
help absorb energy while lowering vehicle weight. Plastics are also used in door modules
maintain or improve side impact safety, plastic layers in automotive safety glass prevent
passenger injuries, and plastic foams can add strength to automotive body cavities and increase
occupant safety in vehicles.
Automotive Electrical Systems Over the last 20 years, the electrical systems of light vehicleshave undergone a major revolution. Automotive electrical and electronic system componentsare now more numerous and important with computer chips regulating and monitoring ABS
brakes, fuel injection, and oxygen sensors, GPS navigation equipment, obstacle sensors, state-
of-the-art audio systems, and other systems. Plastics make possible the inclusion, operation,
interconnection and housing of sockets, switches, connectors, circuit boards, wiring and cable,
and other electrical and electronic devices.
-
7/30/2019 Chemistry and Light Vehicles 2012
8/19
7 | P a g e
Automotive Chassis - A chassis is the supporting frame of a light vehicle. It gives the vehiclestrength and rigidity, and helps increase crash-resistance through energy absorption. The
chassis is especially important in ensuring low levels of noise, vibration and harshness (NVH)
throughout the vehicle. Not only does a reduction in NVH allow for a more pleasant driving
experience, but by putting less stress on connecting components it can help increase the life
span of these components. The key determinant permitting reduced levels of NVH is energy
absorption. As a result, passenger protection can be enhanced in the event of a collision.Plastics are making inroads into the chassis market. Innovations in plastic technology have
brought about the development of successful chassis applications and structure, support and
suspension performance that would not be possible using any other family of materials.
Automotive Powertrains - The powertrain is one of a light vehicles most complicated parts.The term "powertrain" refers to the system of bearings, shafts, and gears that transmit the
engine's power to the axle. Plastics help reduce the number of parts needed to assemble these
complex components. Plastics also help reduce vehicle weight, which helps lower assembly
costs while increasing fuel efficiency.
Automotive Fuel Systems - For automotive fuel system components, plastics have severaladvantages that enable it to outperform metals. Plastic frees engineers from the design
constraints that metal imposes. Plastic's light weight makes vehicles more fuel-efficient and
from a safety standpoint, rupture-resistant plastics with high impact strength are helping keep
automotive fuel tanks and related delivery systems leak-proof, corrosion-resistant, and reliable.
Automotive Engine Components - Many of today's automotive engine components are plastic.From air-intake manifolds and systems to cooling systems to valve covers and other engineparts, plastic helps make engine systems easier to design, easier to assemble, and lighter in
weight. Plastics' versatility has revolutionized automotive engine component design.
The automotive market is an important market for plastic resins such as polypropylene, polyurethane,
nylon, other engineering polymers, and thermoplastic polyesters. Light vehicle applications account for
over 30% of the demand for each resin. Other resins include ABS and polyvinyl butyral. For the latter
resin which is used in safety glass, the automotive market accounts for over 85% of total demand.
Engineering polymers such as nylon, polycarbonate and others are supplanting metals in manyapplications. Typical plastics and composite applications include exterior panels, trim, and bumper
fascia, as well as interior trim panels, window encapsulation, headlamp housings, manifolds and valve
covers, electronic/electric parts and components, wiring harnesses, steering wheels, insulation,
dampening and deadeners, upholstery, mechanical parts and components, safety glass, and myriad
other uses.
Average plastics and composites per vehicle use rose six pounds (1.6%) to 377 pounds in 2011, and
plastics and composites maintained its share of the total vehicle weight. Over 15 major resins find
-
7/30/2019 Chemistry and Light Vehicles 2012
9/19
8 | P a g e
significant use in light vehicles. Details on resin use are presented in Tables 3 and 4. Major polymers
used in light vehicles include 90 pounds of polypropylene (PP), 58 pounds of polyurethanes, 46 pounds
of nylon, 30 pounds of polyvinyl chloride (PVC), 24 pounds of acrylonitrile-butadiene-styrene (ABS), 20
pounds of polycarbonate resins and 18 pounds of polyethylene resins. Among the resins gaining share
during 2011 were polypropylene, nylon, polycarbonate resins, and other engineering resins.
Figure 3
Average Plastics/Composites Use in Light Vehicles in 2011 (pounds/vehicle)
0 10 20 30 40 50 60 70 80 90 100
Polypropylene
Polyurethanes
Nylon
Polyvinyl Chloride
ABS
Polyethylenes
Polycarbonate
Other Engineering Resins
Polyvinyl Butyral
Other
-
7/30/2019 Chemistry and Light Vehicles 2012
10/19
9 | P a g e
Table 3
Average Large Volume Plastics Content of North American Light Vehicles (pounds per vehicle)
2001 2002 2003 2004 2005 2006 2007 2008 2009 2010 2011
Total Plastic/Composites 298 307 319 338 334 341 338 347 369 371 377
Polypropylene 66 72 78 79 77 81 80 79 83 88 90
Polyurethanes 58 57 60 64 64 59 56 57 59 58 58
Nylon 37 38 39 43 42 41 42 42 44 44 46
Polyvinyl Chloride 23 23 23 25 23 27 28 29 30 31 30
ABS 22 26 25 26 25 23 22 24 28 24 24
Polyethylenes 13 12 12 14 13 14 15 17 19 18 18
Polycarbonate 12 11 12 14 14 15 15 18 19 21 20
Other Engineering Resins 33 33 36 38 38 42 42 42 45 46 48
Polyvinyl Butyral 6 6 6 7 7 7 7 7 7 7 7
Other 29 27 28 30 31 31 30 33 34 34 35
Total Plastic/Composites 100.0% 100.0% 100.0% 100.0% 100.0% 100.0% 100.0% 100.0% 100.0% 100.0% 100.0%
Polypropylene 22.1% 23.6% 24.4% 23.3% 23.1% 23.9% 23.7% 22.7% 22.5% 23.8% 23.9%Polyurethanes 19.3% 18.6% 18.7% 18.9% 19.1% 17.3% 16.7% 16.3% 16.0% 15.7% 15.4%
Nylon 12.4% 12.5% 12.3% 12.7% 12.7% 12.1% 12.4% 12.1% 11.9% 12.0% 12.2%
Polyvinyl Chloride 7.9% 7.6% 7.2% 7.3% 7.0% 8.1% 8.2% 8.3% 8.0% 8.3% 7.9%
ABS 7.4% 8.6% 7.9% 7.8% 7.6% 6.9% 6.5% 6.8% 7.6% 6.4% 6.4%
Polyethylenes 4.4% 4.0% 3.7% 4.0% 3.8% 4.0% 4.4% 4.9% 5.0% 4.8% 4.8%
Polycarbonate 3.9% 3.7% 3.9% 4.1% 4.3% 4.3% 4.5% 5.2% 5.3% 5.6% 5.4%
Other Engineering Resins 10.9% 10.7% 11.2% 11.2% 11.3% 12.2% 12.3% 12.1% 12.3% 12.5% 12.8%
Polyvinyl Butyral 2.1% 1.9% 1.9% 1.9% 2.0% 2.1% 2.2% 2.2% 2.0% 1.9% 1.9%
Other 9.8% 8.9% 8.7% 8.8% 9.1% 9.2% 9.0% 9.4% 9.3% 9.1% 9.3%
Note: Polypropylene is also used in thermoplastics polyolefin elastomers (TPO) as well but its use in that area is reportedseparately under rubber in Table 2.
Over the last two decades, other engineering resins such as polyacetal, polyphenylene ether (PPE), and
thermoplastic polyester engineering resins have supplanted metals in a number of applications.
Average use of these resins reached 48 pounds in 2011, up from 31 pounds in 2000 and 19 pounds in
1990. Polycarbonate and nylon are also classified as engineering resins (as are some ABS grades) and if
polycarbonate and nylon resins were included, total engineering resin consumption would be 114
pounds. An average of seven pounds are polyvinyl butyral are used. Additional resins such as acrylics,
phenolics, unsaturated polyester, and others account for the remaining 35 pounds.
-
7/30/2019 Chemistry and Light Vehicles 2012
11/19
10 | P a g e
Table 4
Average Engineering & Other Plastics Content of North American Light Vehicles (pounds per vehicle)
2001 2002 2003 2004 2005 2006 2007 2008 2009 2010 2011
Other Engineering Resins 33 33 36 38 38 42 42 42 45 46 48
Polyacetal 6 6 5 6 6 6 6 7 7 7 8
Polyphenylene Ether (PPE) 10 10 10 10 11 13 13 14 12 13 14
Thermoplastic Polyester
Engineering Resins15 16 19 20 19 20 20 19 23 23 24
All Other Engineering Resins 1 1 2 2 2 2 2 3 3 3 3
Total Plastic/Composites 29 27 28 30 31 31 30 33 34 34 35
Acrylics 4 4 5 5 5 5 5 5 5 4 4
Phenolics 10 9 9 9 9 10 10 11 11 13 13
Unsaturated Polyester 13 12 11 13 14 14 13 13 15 13 13
All Other Resins 2 2 2 3 3 3 3 4 5 4 4
Additional opportunities to reduce weight with plastics and composites are possible. These include: 1)
reducing the weight of existing plastic and composite parts with the use of low density additives,
nanoparticles, and alternate fibers; and 2) converting more metal parts to plastics and composites. As a
result, the light vehicle market presents significant opportunities for further diffusion of plastics and
composites in the future.
Other Chemical Products and Light VehiclesA variety of other products of chemistry are used in the manufacture of light vehicles. Most chemistry
is used in processing and other indirect chemistry (e.g., soda ash in glass manufacture) but also over
300 pounds of rubber, textiles and coatings are used as well.
The typical light vehicle utilizes 222 pounds of rubber, mainly in tires but also in non-tire applications
such as belts and hoses, and other components. Natural rubber is used but by far the most widely used
rubber is styrene-butadiene rubber (SBR) which is used in tire and a variety of non-tire applications.
Common uses include radiator and heater hoses, various body and chassis parts, bumpers, weather-
stripping, door and window seals, mats, grommets, tubes, fan belts and various molded and extruded
goods. Thermoplastic polyolefin elastomers (TPO) are another widely used elastomer. Applications
include a wide variety of exterior, interior and under-the-hood and chassis applications. Combined,
natural rubber, SBR and TPO elastomers account for three-fourths of overall rubber consumption.
Other elastomers include butyl rubber, chlorinated polyethylene, chlorosulfonated polyethylene,
copolyester-ether, ethylene-propylene, nitrile, polybutadiene, polychloroprene (neoprene),polyisopree, polyurethane, silicone, styrenic thermoplastics and other elastomers.
The typical light vehicle utilizes 48 pounds of man-made fibers, primarily synthetic fibers. Very few
natural fibers are used and rayon and melamine fiber use has largely disappeared. Most notable
synthetic fibers are traditional woven fibers of nylon and polyester but also non-woven fabrics of
polypropylene and polyester used in various facings, backings, liners, acoustic panels, reinforcements
-
7/30/2019 Chemistry and Light Vehicles 2012
12/19
11 | P a g e
and panels, and automotive filters. In recent years, traditional textiles are being supplanted by
polyurethanes.
The typical North American light vehicle also featured 34 pounds of coatings (dry weight) in 2011. In
automotive applications, coatings enhance value by making the vehicle attractive and protecting it.
Without coatings, vehicles would quickly rust, be dull in appearance, and have a very short service life.
Light vehicle applications include topcoats, primers and coatings for underbody components andinclude solvent-borne, water-borne and powder coatings. Powder coatings are based mainly on epoxy
and polyester resins, which upon heating react with curing agents to form very durable coatings that
emit virtually zero VOCs (volatile organic compounds). These have gained in use relative to traditional
solvent-borne coatings in recent decades. Coatings use has declined in recent years because of
reduced waste generation during application, thinner coatings, and the switch to higher solids
coatings.
In addition to these materials, chemistry also plays a role in the 223 pounds of fluids and lubricants
that a typical light vehicle contains. These include engine oil lubricants, transmissions fluids, windshield
wiper fluids, refrigerants for air conditioners, and other products. All of these contain chemical
additives to enhance performance while others such as fluorocarbon refrigerants are products of
chemistry. In engine oil lubricants, synthetic lubricants are gaining market share away from traditional
petroleum products.
Energy Savings, Chemistry and Light VehiclesThe products of the business of chemistry (plastic resins, catalysts, etc.) to a very large degree help the
light vehicle industry and consumers save energy and ultimately reduce greenhouse gas emissions.
Chemistry has played a leading role in improving fuel efficiency. According to the EPA, for example, the
average fuel efficiency (as measured in miles per gallon, or MPG) for model 2011 vehicles was 22.8
MPG, compared to 19.8 MPG in 2000 and 21.2 MPG in 1990. Rising popularity of SUVs and light-duty
trucks was one factor behind this declining average fuel efficiency. However, if it werent for chemistry-- in particular, the use of plastics resins/composites in light-weighting average fuel efficiency would
be much lower. Fuel efficiency in the absence of chemistry could be as low as 16.2 MPG.
According to the latest EIA Annual Energy Outlook, the use of gasoline by light vehicles amounted to
15.62 quadrillion British thermal units (BTUs), or 15.62 quads in 2011. The use of chemistry products in
various energy-saving applications in light vehicles saved between 2.26-4.40 quads of energy in 2011.
Most of these savings arise from weight reduction and improved fuel efficiency from light-weighting
efforts. Other areas improving fuel efficiency include better performing oil and fuel additives, advanced
catalysis, and greater rolling resistance through advances in elastomer chemistry among other
applications. In other words, without the benefits of chemistry, energy consumption by light vehicleswould be 14.4% to 28.2% above current levels. The energy savings of 2.26-4.40 quads is the equivalent
of 1.1 million to 2.1 million barrels of oil per day.
-
7/30/2019 Chemistry and Light Vehicles 2012
13/19
12 | P a g e
Table 5
2011 Energy Savings from Chemistry by Area of Applications
Fuel Use
(trillion BTUs)
MPG
Equivalent
Low High Low High
Plastics Light-Weighting 1,494 2,611 3.0 3.9Fuel Additives 264 310 0.4 0.5
Oil Additives 303 885 0.4 1.3
Improved Catalytic Converters 109 435 0.2 0.6
Lower Roll Resistance & Other
Rubber Technology40 96 0.1 0.1
Other 49 61 0.1 0.1
Total 2,258 4,398 3.3 6.6
Light-Weighting - The use of plastics and composites in light vehicles has been rising steadily for nearly
40 years. Polymers not only reduce costs and allow for more appealing and function design, they alsofoster significant weight reduction. The favorable performance properties of plastics and composites
are manifold, but weight-savings is primary among these.
Each pound of plastics and composites, for example, supplants 2-3 pounds of other, heavier materials.
As a result, polymers help to reduce vehicle weight, thus improving fuel efficiency and reducing
greenhouse gas (GHG) emissions. The light vehicle market presents significant opportunities for further
diffusion of polymers in the future.
Substantial weight reduction is possible as composites are typically up to 40% lighter than steel parts of
equal strength. In addition to light-weighting to improve fuel efficiency and reduce emissions, plastics
and composites also enhance design flexibility, allow exceptional aerodynamic modeling, enhance
safety, provide unparalleled corrosion and damage (dent and ding) resistance, enable better internal
damping (reduced noise, vibration and harshness), and consolidate parts and assembly time. In
addition, tooling for composites parts can be as much as 80% lower than comparable steel parts. There
are more than 30 different applications in light vehicles in which plastics and composites provide
weight reduction and reduced fuel consumption. These applications can be aggregated into four main
categories:
1. Chassis2. Under-the-hood3. Body4. Interior
For each of these applications, the average weight savings and energy savings were aggregated and
this was compared to savings via competing materials. Taken together, the automotive weight
reduction through the use of plastics and composites in light-weighting resulted in energy savings on
the order of 1.49-2.61 quads (the equivalent of 3.0-3.9 MPG). High-density polyethylene (HDPE),
polypropylene, polyamide, and polyetheretherketone (PEEK) resins, for example, are supplanting steel
and aluminum in a number of applications, polycarbonate is supplanting glass, and polyurethane is
-
7/30/2019 Chemistry and Light Vehicles 2012
14/19
13 | P a g e
supplanting textiles. Another example is found with traditional aluminum air intake manifolds that are
gradually being replaced by polyamide resins. The latter at 3.3 pounds provides weight savings of 50%.
Moreover, their resistance to oils and greases has led to the use of polyamides in engine covers, gears
and bearings.
Fuel Additives - Gasoline additives increase gasoline's octane rating or act as corrosion inhibitors orlubricants, thus allowing the use of higher compression ratios for greater fuel efficiency and power.
Types of additives include metal deactivators, corrosion inhibitors, oxygenates and antioxidants.
Gasoline combustion results in the formation of engine deposits in fuel injectors and on intake valves,
which typically results in reduced engine performance (and increased emissions). Detergent,
dispersants and full-deposit-control additives help clean and prevent engine deposits, thus boosting
fuel efficiency. Gasoline detergent additives have been used by gasoline marketers since the 1960s to
help control engine deposits but in recent decades they have evolved into full-deposit-control
detergent additives. The EPA requires that all gasoline sold to consumers contain a minimum level of
detergent additive. In a similar manner, diesel fuel additives reduce fuel consumption (and emissions)
over the life time of a vehicle. Fuel additives resulted in energy savings on the order of 264-310 trillion
BTUs; the equivalent of 0.4-0.5 MPG in 2011.
Improved Oil Additives - Oil additives are used with base oil to enhance lubrication in automotive
engines. These help to reduce friction, wear, corrosion and oxidation, all of which may contribute to
compression problems. Improving engine oil additives allows greater fuel efficiency in light vehicles.
These also support additional engine power. Gas mileage can be significantly improved by using more
advanced motor oils. This includes regular oil with additives or synthetic motor oil, which is created in
the research and development lab and not from petroleum-based crude oil. Synthetic oils are
specifically designed to reduce friction. While more expensive than organic petroleum-based oil, they
last a lot longer, and thus the change interval for synthetic oil is longer than the change interval for
petroleum-based oil. Overall, the use of advanced oil additives and synthetic motor oils in gasolineengines improves fuel mileage by 2% to 6%. In diesel engines, fuel savings of 5% to 18% are possible
with fuel additives and catalysts. In addition to significant fuel savings, emissions reductions and
prolonged engine life are achieved. The advances in oil additives resulted in energy savings on the
order of 303-885 trillion BTUs; the equivalent of 0.4 to 1.3 MPG in 2011.
Catalysis - A catalytic converter is a vehicle emissions control device that converts toxic by-products of
combustion in the exhaust of an internal combustion engine to less toxic substances by way of
catalyzed chemical reactions. Most modern catalytic converters contain two distinct catalysts: the
reduction catalyst and the oxidation catalyst. First introduced in the 1975 model year, the diffusion of
lean-burn engines with "three-way" converters in the 1980s resulted in improved efficiency. These
three-way units rely on advanced catalyst chemistry that stores and releases oxygen on a single
substrate. Catalysts used in catalytic converters are precious metals such as platinum, palladium, and
rhodium coated on the surface of ceramic honeycomb structures. Improved thermal and conversion
efficiency and durability occur while reducing the size and weight of converters. These advances in
catalysts resulted in energy savings on the order of 109-435 trillion BTUs; the equivalent of 0.2 to 0.6
MPG in 2011.
-
7/30/2019 Chemistry and Light Vehicles 2012
15/19
14 | P a g e
Rolling Resistance & Elastomer Chemistry Styrene-butadiene rubber (SBR) is the most widely used
rubber in tires. Compared to natural rubber, SBR improves automotive fuel efficiency, extends the life
of the tire (product life), and decreases scrapping of tires. SBR also enhances performance (cornering,
speed, stopping, etc.). Other synthetic elastomer compounds provide similar performance attributes
including energy savings. In tires, rolling resistance is a factor in fuel efficiency. This is the amount of
force needed to keep tires moving at a constant speed. The greater the force needed; the higher fuel
consumption. The U.S. Department of Energy estimates that 5%-15% of fuel consumption is used toovercome rolling resistance for light vehicles. Some kinds of fuel efficient tires are engineered to utilize
lower rolling resistance and reduce the strain on the engine. The concept behind low rolling resistance
tires is that they require less energy. Although design plays the largest role, chemistry also plays an
important role. In particular, the use of silica and more highly activated carbon blacks in combination
with blends of solution polymerized SBR and natural rubber have fostered low rolling resistance. An
analysis by the National Renewable Energy Laboratory indicates the sensitivity coefficient (percent
increase in fuel economy per percent decrease in rolling resistance) to be as high as 0.2 for a
conventional vehicle. A Green Seal report, Low Rolling Resistance Tires, indicates that a 1.5%-4.5%
savings is possible for high rolling resistance tires. Most roll resistance tires offer 10% improvements (in
some cases 20%) in roll resistance if proper maintenance is achieved. This isnt always possible and the
diffusion of the technology is only modest. In addition, tire design plays a dominant role. Nonetheless,
the energy savings from low resistance tires and from more advanced elastomer technology (including
rubber additives) suggests that energy savings from chemistry resulted in energy savings on the order
of 40-96 trillion BTUs; the equivalent of 0.1 MPG in 2011.
Other - While the products of chemistry improve energy efficiency in other areas, the extent is difficult
to quantify. The use of plastics and composites, for example, may provide more aerodynamic designs.
New automotive OEM coatings may feature improved drag resistance and thus energy savings. Other
fluids such as brake fluids and automatic transmission fluids and the use of non-woven fabrics may also
enhance energy efficiency. Advances in chemistry are also aiding battery technology, not only in
lithium and other advanced batteries but also in lead acid batteries. Finally, silicon and other chemistryare making possible the use of sensors, advanced displays, and other innovative electronics which can
contribute to energy efficiencies as well. All together, the energy savings from these applications for
chemistry resulted in savings on the order of 49-61 trillion BTUs; the equivalent of 0.1 MPG in 2011.
The difficulty in quantifying energy savings is especially the case in examining the energy savings over
the life cycle of a product. For example, it is catalysis that engenders modern oil refining and
concomitant increase in yields. That is, the portion of every barrel of oil that can be processed into
product. Fluid catalytic cracking allows high conversion. In addition, work-over and completion fluids,
cementing and other stimulation chemicals, and other oilfield chemicals provide for greater recovery
of oil in mature oilfields. Other energy efficiency-enhancing technologies such as bio-fuels, advanced
batteries, hydrogen and fuel cells all rely upon chemistry. These energy savings are outside the scope
of this analysis and arent included.
-
7/30/2019 Chemistry and Light Vehicles 2012
16/19
15 | P a g e
SummaryThe $142 billion light vehicle industry represents an important sector of the US economy and a large
end-use customer market for chemistry. In 2011, the 10.57 million light vehicles assembled in the
United States and Canada required $38.4 billion in chemistry (chemical products and chemical
processing), or $3,636 of chemistry in every vehicle. This is up significantly from $2,444 in 2006 and
$1,740 in 2001.
The latest data indicate that the average weight of North American light vehicles continues to rise. The
use of plastics and composites in light vehicles continues to rise as well, reaching 377 pounds per
vehicle in 2011. In addition to plastics and composites, the typical light vehicle also utilizes 222 pounds
of rubber and 48 pounds of man-made fibers. The latter are primarily synthetic fibers. The typical
North American light vehicle also featured 34 pounds of coatings (dry weight) in 2011.
The products of the business of chemistry (plastic resins, catalysts, etc.) to a very large degree help the
light vehicle industry and consumers save energy and ultimately reduce greenhouse gas emissions.
Chemistry has played a leading role in improving fuel efficiency. For example, the average fuel
efficiency (as measured in miles per gallon, or MPG) for model 2011 vehicles was 22.8 MPG2. If it
werent for chemistry -- in particular, the use of plastics resins and composites in light-weighting
average fuel efficiency would be much lower perhaps as low as only 16.2 MPG.
The use of gasoline by light vehicles amounted to 15.62 quadrillion British thermal units (BTUs), or
15.62 quads in 2011. The energy savings of 2.26 to 4.40 quads is the equivalent of 1.1-2.1 million
barrels of oil per day. In other words, in absence of the benefits of chemistry, energy consumption by
light vehicles would be 14.4%-28.2% above their current levels. Most of the energy savings arose from
weight reduction and improved fuel efficiency from light-weighting efforts. Other areas where
chemistry has improved fuel efficiency include better performing oil and fuel additives, advanced
catalysis, and greater rolling resistance through advances in elastomer chemistry among other
applications.
2Source: Environmental Protection Agency
-
7/30/2019 Chemistry and Light Vehicles 2012
17/19
16 | P a g e
Economics and Statistics DepartmentThe Economics & Statistics Department provides a full range of statistical and economic advice and
services for ACC and its members and other partners. The group works to improve overall ACC
advocacy impact by providing statistics on American Chemistry as well as preparing information about
the economic value and contributions of American Chemistry to our economy and society. They
function as an in-house consultant, providing survey, economic analysis and other statistical expertise,
as well as monitoring business conditions and changing industry dynamics. The group also offersextensive industry knowledge, a network of leading academic organizations and think tanks, and a
dedication to making analysis relevant and comprehensible to a wide audience.
Dr. Thomas Kevin Swift
Chief Economist and Managing Director
202.249.6180
Martha Gilchrist Moore
Senior Director Policy Analysis and Economics
202.249.6182
Dr. Smita Bhatia
Director, Chemistry and Industry Dynamics
202.249.6184
Emily Sanchez
Director, Surveys & Statistics and Editor
mailto:[email protected]:[email protected]:[email protected]:[email protected]:[email protected]:[email protected]:[email protected]:[email protected] -
7/30/2019 Chemistry and Light Vehicles 2012
18/19
17 | P a g e
Appendix: Data Sources and MethodologyThe information presented in this report is an update building on ACCs earlier assessments of
materials use per vehicle. Those previous assessments depended upon the materials use per vehicle
data supplied by American Metal Market with some adjustments for non-automobile light vehicles
(SUVs, light-duty trucks, mini-vans, etc.) The reporter who tabulated this data, however, has retired
and the data are no longer available. The assessment presented here reflects an attempt to resurrect
and re-estimate the data for materials use per vehicle. While the original data reflected typicaldomestic automobile use of materials, the present assessment reflects the average for all light vehicles
on an OEM (original equipment manufacturer) basis.
A bottoms-up approach was taken by examining light vehicle use by type of material. The data for
the materials use were provided by trade associations and government statistical agencies. Data
sources include The Aluminum Association, American Composite Manufacturers Association, American
Fiber Manufacturers Association, American Iron & Steel Institute, Copper Development Association,
International Magnesium Association, and the Rubber Manufacturers Association. The provision of
data and advice from these associations are gratefully acknowledged. Data from the Bureau of the
Census and the US Geological Survey were also used.
The plastics and composite data are derived from the American Chemistry Councils Plastics Industry
Producers Statistics (PIPS) service, which provides relevant, timely, comprehensive and accurate
business statistics on the plastic resins industry. This was supplemented by an exhaustive search of the
trade literature. The averages are calculated using an assessment of the material consumed with
adjustments made to take into account replacement demand. The sum of the individual materials data
are close to the comparable average vehicle data provided by the Environmental Protection Agency
(EPA) and the Office of Energy Efficiency and Renewable Energy (EERE) of the US Department of Energy
(DOE).
This 2012 edition of the report has been expanded to include an assessment of how (and to whatextent) chemistry plays a role in fostering energy efficiency in light vehicles. The analysis was based on
previous econometric analysis, technical information and estimates, and analysis conducted by
McKinsey & Company.
Using econometrics, ACC has analyzed the relationship between fuel efficiency relative to vehicle
weight, horsepower, and other performance metrics. Using historical data on materials composition,
the results of the ACC analysis indicates that for each 10 pound increase in plastics substitution for
other materials, a vehicles fuel efficiency improves by 0.11% to 0.14%.
A literature search of energy savings was conducted. The various applications in which chemistry plays
a role in improving energy efficiency were identified. These included oil and fuel additives, catalysis,
rolling resistance and elastomer chemistry, and other areas in which chemistry improved miles per
gallons. A search of the technical (scientific and engineering) literature provided various estimates of
the energy savings. In 2009, on behalf of the International Council of Chemical Associations (ICCA),
McKinsey & Company developed estimates of the global greenhouse gas savings attributable to use of
chemistry products. These included applications in lighting, household operations, and light vehicles
among others. This study by McKinsey and Company found that the use of plastics and composites for
automotive weight reduction enable a savings of three units of GHG emissions for every unit emitted
-
7/30/2019 Chemistry and Light Vehicles 2012
19/19
during production. Since the data in the ICCA study reflected global coverage, we used US values
where available or made adjustments to reflect US conditions in each of the various cases, or end-uses.
The larger size of a typical American light vehicle is larger (and feature a larger plastics and chemistry
component) in the United States than in Europe and Japan. As a result, light vehicles will figure more
prominently among end-use markets for chemistry in the United States. On the other hand, existing
relative weight- (and energy-) savings in Europe and Japan may be more extensive in this end-use,
somewhat offsetting the greater prominence in the United States. Using a variety of sources, a rangeof estimates (low and high) is provided.
Every effort has been made in the preparation of this publication to provide the best available
information. However, neither the American Chemistry Council, nor any of its employees, agents or
other assigns makes any warranty, expressed or implied, or assumes any liability or responsibility for
any use, or the results of such use, of any information or data disclosed in this material.