CHEMICALS

For the latest information–www.gcelectronics.comAll quantities are single; BU’s are packages of 10 Unless otherwise noted.

Chem

55

THINNERS & SOLVENTS

Paint ThinnerAll purpose mineral spirit type thinner andsolvent for paint and varnish base products.

Part No. 10-6702 2 fl. oz. BottleN.S.N. 8010-00-054-1521

Polystyrene Q-Dope Thinner For thinning polystyrene base coil dopes andcements. Can also be used for cementing polystyrene parts.

Part No. 10-4102 2 fl. oz. BottleN.S.N. 8010-00-063-1376N.S.N. 8040-00-902-1159

Radio-TV Cement SolventFast acting solvent formulated for use inspeaker repair. Dissolves cement on speakercones, spiders, frames, voice-coils. May alsobe used as a thinner for all lacquer typecements.Part No. 10-312 2 fl. oz. Bottle

Part No. 10-320 16 fl. oz. BottleN.S.N. 8010-00-775-5893

Part No. 10-321 1 gal. Can

Part No. 10-321 4 gal. Pack

Print Kote SolventA solvent to remove silicone and othertypes of protective coatings from PC boards.Required when modifying PC boards orreplacing components where the protectivecoating interferes with the desoldering andresoldering operation.

Part No. 22-209 2 fl. oz. BottleN.S.N. 6810-00-711-2185

COATINGSSilver Print II(Conductive Paint)For PC repair or add-on circuit traces. Puresilver in acrylic lacquer based carrier maybe brushed on for either conductors orshielding. Connections have equal or betterconductivity than copper (0.1 ohms persquare inch).

Part No. 22-023 1/2 troy oz. Bottle

Part No. 22-024 1 troy oz. Bottle

Red Insulating VarnishAlkyd-based compound, especially resistantto environmental extremes including oils,water and most acids and alkalis. Retains itshigh dielectric strength even if wet and is,therefore, especially adaptable to theinsulation of electrical and electronicdevices or components which may beoperated in a very humid climate and up to250°F (121°C). For general insulation ofcoils, transformers, motor windings and forall-around protection against oxidation andatmospheric attacks.

Part No. 10-9002-A 2 fl. oz. Bottle w/BrushN.S.N. 5970-00-901-5331

Part No. 10-9008-A 8 fl. oz. Bottle

Print Kote Conformal CoatingThe ultimate coating for PC boards providesa protective shield to resist environmentalcontaminants. Prevents arcing and shorting.Air dry 15 to 30 minutes. May be baked at200°C for 30-60 minutes for extreme hightemperature applications.

Part No. 22-203 2 fl. oz. BottleN.S.N. 8010-00-711-2173

CHEMICALS

For the latest information–www.gcelectronics.com All quantities are single; BU’s are packages of 10 Unless otherwise noted.

Chem

67

CHEMICAL SPECIFICATION MATRIX (Cont.)

Printed Circuit Products SpecificationsHMIS

Flammability Specific Shelf Life DOTPart No. MSDS Description Contents Base Color Rating Gravity Months* Shipping

22-225-A 320208

Positive Type 2 fl. Oz Sodium Milky White 0 1.08 42 UN 1824ORM-D22-226 Developer 6 fl. Oz Hydroxide

Concentrate

22-237 306 PC Board 6 fl.oz Ferric Chloride& Water §

Dark 0 1.42 42 UN 2582ORM-D22-238 Etching Solution 32 fl oz

§ pH Level = 1.57

Brown22-239 1 gal.

22-240 104 Stripping 2 fl. Oz MEK & Clear 3 0.84 42 UN 1993ORM-DSolution Xylene

22-244 131 Etch Resist 2 fl. Oz Hydrocarbon Black 3 0.92 36 UN 1263ORM-DLacquer Solvent

Silicone Sealants SpecificationsHMIS

Specific Flammability Specific Tensile Dielectric Shelf Life DotPart No. MSDS Description Contents Base Color Rating Gravity Consistency Strength Strength Temperature Months* Shipping

10-150 149 Silicone Rubber 3 fl.oz Vulcanized Clear 1 1.03 Non-Slump 220 psi 500 v/mil -80°F to 400°F 18 Not Adhesive/Sealant Silicone Paste Regulated

19-155 201 Electronic Grade 3 fl.oz Vulcanized Clear 0 1.04 Non-Slump 225-275 psi 18 KV/mm -70°F to 400°F 12 Not Silicone Silicone Paste Regulated

Sealant/Adhesive

19-158 275 Electronic Grade 10.2 fl oz Vulcanized White 0 1.04 Non-Slump 225-275 psi 18 KV/mm -70°F to 400°F 12 Not Silicone Silicone Paste Regulated

Sealant/Adhesive19-159 2.8 fl oz

EL-615 202 Silicone Caulk 10.2 fl oz Vulcanized Clear 1 1.03 Non-Slump 220 psi 25 KV/mm -70°F to 400°F 18 Not Tube Silicone Paste Regulated

Coating SpecificationsHMIS

Flammability Specific Drying Dielectric Useful Temp. Suggested Shelf Life DOT Contents Base Color Rating Gravity Time Strength Range Solvent Months* Shipping

22-023 278 Silver Print II 1/2 troy oz. Acrylic Silver 3 1.76 Dry 20-30 min. Butyl Acetate 12 UN 1307ORM-D22-024 1 troy oz. Force Dry 30 min

@ 80ºC

10-9002 307 Red 2 fl. oz. Alkyd-Resin Red 3 1.100 8-24 hours Air Dry @ 77°F

40 – 55 sec. #3 EZ Zahn Cup @ 77ºF

Up to 93ºC Use Xylene or 22-209

12 UN 1263ORM-D10-9008 Insulation 8 fl. oz. Based Enamel (200ºF)

Varnish 3,000 v/Mil22-203 138 Print Kote 2 fl. oz. High Polymer Clear 3 0.880 Air Dry 850 cp @ 25ºC

1,400 v/Mil-65ºC to 200ºC Use 18 UN 1993

ORM-DConformal Silicone Resin 15-30 mins. (-85ºF to 392ºF) 22-209Coating

10-1762 135 Insulating 2 fl. oz. Synthetic Resin Black 3 0.930 4 hrs. 7,000 - 22,000 cps1,400 v/Mil

-30ºF to +200ºF 12 UN 1139ORM-D10-1766 Coating 16 fl. oz. in Solvent

Use Toluene or 22-209

10-8665 159 Acrylic 11 oz. aerosol Polymeric Clear 4 0.740 10 mins 250 CP @ 25ºC

3,800 v/Mil

Up to 190ºC Use Toluene 30 ORM-D

209 Corona Dope 2 fl. oz. Cellulose Black 3 0.900 30-60 mins. 220 CP @ 25ºC Up to 340ºF 36UN 1263ORM-D

10-4702 10-312 or LacquerThinner

10-5002 137 Red-X 2 fl. oz. Thixotopic Red 3 1.120 2 hrs. 200-400 CP @ 25ºC2,000 v/Mil

Up to 105ºC Xylene 36 UN 1263ORM-DCorona Dope Polyester Enamel (220˚ F)

10-3702 101 Q Dope 2 fl. oz. Styrene Milky 3 0.878 ± 0.040 80% Strength: 72 Hr.

Use 36 ORM-D10-3704 4 fl. oz. White 10-410210-3709 1 gal. UN 1133

*Note: Shelf Life is determined by the Date Of Manufacture (DOM) located on the product. If a product has a shelf life of 12 months, a closed container is good for one year past the DOM.

Part No. MSDS Description

-70°F to 400°F

N/A N/A

N/A720 cps

CHEMICALS

Phone (815)316-9080•Fax (815)316-9081All quantities are single; BU’s are packages of 10 Unless otherwise noted.

Che

m

56

COATINGS (Cont.)

Insulating CoatingHeavy-bodied, black insulating coating whichreplaces insulating tape in applications wherewrap-around tape could not readily beapplied. This compound dries quickly to astrong pliable finish that will not crack, peel orchip. It is water and oil proof and may be usedoutdoors to insulate any electrical terminal,connection or wire splice. Excellent forproviding insulation on handles, etc. Voltagerating 1400v/mil (min.)

Part No. 10-1762 2 fl. oz. Bottle with Brush

Part No. 10-1766 16 fl. oz. Bottle

Corona DopeThis lacquer has excellent dielectric, arcand corona resisting properties, andprotects surfaces against moisture.Achieved with a quick drying, blacklacquer insulating coating, based on acellulose resin. Temperature range: to325°F (163°C). This lacquer is used to coatflybacks, coils, transformers to improve theinsulation and weather resistant propertiesof wires. Dielectric Strength: 3,800Volts/Mil Min.

Part No. 10-4702 2 fl. oz. Bottle with BrushN.S.N. 8030-00-778-4278N.S.N. 5970-00-063-0685

Q DopeSolution of pure polystyrene in solvents.Dries fast and leaves a clear, protective coat-ing on coils and transformers, with no orminimal effect on inductive values. May alsobe used as a cement for molded or fabri-cated items made of polystyrene.

Part No. 10-3702 2 fl. oz. Bottle with BrushN.S.N. 8010-00-868-3866N.S.N. 5970-00-044-6790N.S.N. 5970-00-982-3909

Part No. 10-3704 4 fl. oz. Bottle with BrushN.S.N. 5970-01-047-9265N.S.N. 8040-00-598-9748

Part No. 10-3709 1 gal. CanN.S.N. 8030-00-182-6416

Red-X Corona DopeThixotropic polyester-base red enamel thatwill not drip or sag, has excellent adhesionand is oil and waterproof. Temperaturerange: to 220°F (104°C). An excellentinsulator, corona and spark preventivecoating. For moisture-proofing andinsulation of high voltage coils and otherhigh voltage components, especially in highhumidity problem areas. Also recommendedfor rotor and field coils in motors, to coattransformers, etc. Dielectric strength: 1,700Volts/Mil Min., dielectric constant: 3.7.

Part No. 10-5002 2 fl. oz. Bottle with BrushN.S.N. 8040-00-779-2866

Acrylic PlasticTransparent (glass-like) lacquer. Seals,protects, insulates and tarnish-proofs anyobject to which it is applied. This coatinghas high dielectric strength and resistsmoisture, caustic solutions and alcohols.Used to coat electronic component andconnections as well as metal or art objects(to protect against tarnish and corrosion).

Part No. 10-8665 11 oz. Aerosol