CHEE 32326.1 Main Reactions in FCC Catalysis. CHEE 32326.2 Key Developments in FCC Technology.
-
Upload
margaret-rickson -
Category
Documents
-
view
221 -
download
0
Transcript of CHEE 32326.1 Main Reactions in FCC Catalysis. CHEE 32326.2 Key Developments in FCC Technology.
CHEE 323 26.1
Main Reactions in FCC Catalysis
CHEE 323 26.2
Key Developments in FCC Technology
CHEE 323 26.3
Zeolite Structure
Zeolites are a well-defined class of crystalline aluminosilicate minerals whose 3-dimensional structure is derived from a framework of [SiO4]4- and [AlO4]5- coordination polyhedra.
Usually zeolites are classified according to common structural units (secondary building units, sbus)
Tetrahedra are arranged to yield an open framework structure, as shown below in the most important FCC catalyst, zeolite Y or faujasite.
This class of zeolite has 0.74nm apertures, and the supercage of thestructure has a radius of approx.1.2 nm.
A range of compositions exist, with a unitcell formula typically beingNaj[(AlO2)j(SiO2)192-j]•zH2O where z is about 250 and j is between 48 and 76.
CHEE 323 26.4
Zeolite Structure
Zeolite structure depends on the Si/Al ratio, template agents and preparation, but allhave unique micropore structures.
Virtually all acid catalyzed reactions can be conducted with acidic form
of zeolites, provided the reactant is small enough to enter the pores.
The acidic sites in HZSM-5 are strong enough to protonate paraffins, leading to widespread use as an industrial cat. cracking catalyst.
CHEE 323 26.5
Structure of ZSM-5
The zeolite ZSM-5 is finding greater application in FCC as an octane enhancing catalyst, as it cracks/isomerizes low octane components in the gas boiling range to higher octane value while generating propylene and butylene for subsequent alkylation.
Zeolites are usually crystallizedfrom alkaline aqueous gels attemperatures between 70°C and300°C to produce a sodium salt.
In addition to structure, key propertiesare the Si/Al ratio, the particle sizeand the nature of the (exchanged) cation.
These primary structure/composition factors influence acidity, thermal stability and overall catalytic activity.
CHEE 323 26.6
Acidity of Zeolites
The acidic properties of zeolites are dependent on the method of preparation, form, temperature of dehydration and the Si/Al ratio.
Bronsted Acid Sites:
generated by ion exchangefollowed by calcination
Lewis Acid Sites:
At 550°C, water loss from Bronstedsites leads to unstable Lewis sites,leading to so-called ‘true’ Lewis sitesthrough expelling an Al species.
CHEE 323 26.7
Cracking Catalyst Formulations
In addition to acidity, physical characteristics must be considered, including:1. Mechanical stability
function of zeolite, matrix and binder composition, degree of zeolite dispersion and bulk density.
2. Pore volume, pore size distribution and surface area determined by matrix and zeolite composition, effects activity
and yield through introduction of diffusion effects.
3. Thermal and hydrothermal stability Recrystallization and structure collapse
4. Particle size distribution Fluidization and entrainment specifications require 60-80m
particle diameter
5. Bulk Density
CHEE 323 26.8
Synthesis of FCC Catalysts Utilizing Zeolites
CHEE 323 26.9
Paraffin Cracking Catalyzed by ZSM-5
CHEE 323 26.10
Shape Selectivity Imposed by Zeolite Structure
Variable channel and pore sizes of zeolites can create unique selectivity effects.
Reactant Selectivity:
Products Selectivity:
Restricted transition state selectivity
Transalkylation of a dialkylbenzene
CHEE 323 26.11
Modern FCC Complex
CHEE 323 26.12
Schematic View: Short Contact Time FCC Unit
A modern FCC unit is a short-residence time, adiabatic process where atomized feed is contacted with hot catalyst (500°C) in a relatively narrow riser.
The reaction riser is a fluidized bed, with mixing promoted by differential particle-gas velocity and large scale turbulence.
Upon exiting the riser, the fluid velocity drops, and entrained catalyst settles. The overhead product stream is isolated through a cyclone to remove smaller particles.
Large-scale coke formation deactivates the catalyst, limiting the single-pass activity.
CHEE 323 26.13
Schematic View: Catalyst Regenerator
Coke formation during FCC blocks access to acidic sites within the active zeolite.
While limiting the lifetime of the catalyst, regeneration by coke combustion is very efficient.
The heat of combustion drives the endothermic cracking process by heating the catalyst prior to reintroduction to the riser.
As much as 30 tons per minute of catalyst is regenerated in a full-scale FCC unit.
CHEE 323 26.14
Really, Really Big Reactors
This FFC installation has the regeneration unit constructed above the cracking riser. Side-by-side configurations are also used.
A typical plant can run continuously for several hundred days, processing millions of barrels of oil.
In the foreground of the photo is a heating furnace.
CHEE 323 26.15
Bifunctional Catalysis
HydrocrackingCatalytic cracking and olefin hydrogenation are combined processes in hydrocracking units.
FCC Zeolites, combined with dispersed metals (Ni, Pt, Pd) on a standard matrix generates a bifunctional catalyst capable of utilizing reforming by-product hydrogen.
Naptha ReformingThe low octane number of small paraffins (naptha) can be improved by isomerization without concurrent cracking or alkylation.
Pt/SiO2-Al2O3 is a bifunctional catalyst preparation, wherein the metal catalyzes dehydrogenation and /hydrogenation and the acidic support catalyzes skeletal isomerization.
++
-H2
Pt
Pt
H2
H+
H+
+
+
-