Chapter 1 Part 2 Substructures
Transcript of Chapter 1 Part 2 Substructures
-
8/18/2019 Chapter 1 Part 2 Substructures
1/139
CHAPTER 1: SUBSTRUCTURECHAPTER 1: SUBSTRUCTURE1.2 Building foundation: types and
functions
1.2.1 Shallow Foundation - strip footings , pad footing, raftfoundation.1.2.2 Deep Pile/Foundation
- spun pile, icro pile, !a"au pile, !ore pileand pile cap1.# $olun stup, ground !ea and ground
sla!
1
-
8/18/2019 Chapter 1 Part 2 Substructures
2/139
Wind load
Dead load
Wind load
2
-
8/18/2019 Chapter 1 Part 2 Substructures
3/139
3
-
8/18/2019 Chapter 1 Part 2 Substructures
4/139
What is Substructure?What is Substructure?
FOUNDATION is a part ! SUBSTRUCTUREc"p#e#tsfoundation is the lowest portion of the !uilding
structure. %&tends fro the !earing surface to theain structure.'
(sually located !elow the ground le)el.
* foundation is a part of the structure which is indirect contact with the ground to which the loads aretransitted.
Foundations can !e located at+ !elow ground, at groundle)el, or a!o)e ground le)el.
4
-
8/18/2019 Chapter 1 Part 2 Substructures
5/139
Shallow FoundationDeep Foundation
5
-
8/18/2019 Chapter 1 Part 2 Substructures
6/139
6
-
8/18/2019 Chapter 1 Part 2 Substructures
7/139
Typical types of foundation
7
-
8/18/2019 Chapter 1 Part 2 Substructures
8/139
Main functions of thefoundations
To supports the weight ofstructure and distribute theload of the structure over agreater area.
To transmit the loaduniformly under thestructure.
nchors the structure to the
earth! providing a "rm! leveland strong base over whichthe superstructure may beconstructed.
#
-
8/18/2019 Chapter 1 Part 2 Substructures
9/139
Main functions of thefoundations
To avoid any settlement orother movement that cancause damage to any part ofthe building $a stable
foundation should bear theloads without sin%ing orsettling more than an inch atthe most&.
To increase the stability of the
structure by preventing itstilting or overturning againstwinds! earth'ua%es anduneven distribution of liveload $(ateral )tability&.
*
-
8/18/2019 Chapter 1 Part 2 Substructures
10/139
Selection Criteria
(oading of the building!big load need bigfoundation such as raftfoundation or piling.
Types of soil such as peatsoil prefer piling or deepfoundation
+ost economical but
capable to supportnumbers of building orstorey $pad footing orpilling,&
1-
-
8/18/2019 Chapter 1 Part 2 Substructures
11/139
Selection Criteria The loads that must be transferred from the structure
to the soil strata supporting it. This also shouldevaluate the ability of the soil to support the ultimateloads.
The capability of the structure that will safelytransfer the loads from the superstructure to thefoundation bed.
The possibility and etent of settlement of the soildue to the presence of mines and 'uarries in the
vicinity. The possibility of the underground water has sulfates
or other salts that can degrade the foundationmaterials.
11
-
8/18/2019 Chapter 1 Part 2 Substructures
12/139
Factors That Need To BeConsidered in the Foundation
Design)oil /nvestigation $)./& is needed to determine thesubsoil includes the soil type! strength! soilstructure! moisture conditions and the presence ofroots.
0urpose of )./determine the bearing capacity!seasonal volume changes and other possibleground movements.
ommon methods obtaining soil samplestrial pits!boreholes!window sampling anddynamic probe test.
12
-
8/18/2019 Chapter 1 Part 2 Substructures
13/139
Factors That Need To BeConsidered in the Foundation
Designor more safety precaution use factor ofsafety FOS = 3
/ncrease number of bore hole or
sucient number of borehole so that theresult of the report is more accurate.hoose the critical point load for boreholevery end of the building
)upervise the )./ properly ma%e sure nomista%e
13
-
8/18/2019 Chapter 1 Part 2 Substructures
14/139
Factors That Need To BeConsidered in the Foundation
Designor the safety of the foundation design usethe lowest of bearing capacity value.
The engineer must have good enough datafor the )./ such as previous soil report!cutting or "lling area.
ngineer also must ma%e sure the originalground level and purposed level orformation level while designing thefoundation.
14
-
8/18/2019 Chapter 1 Part 2 Substructures
15/139
Factors That Need To BeConsidered in the Foundation
Design The correct parameter isimportant to prevent fromfoundation failure that may
occur causing building collapse./t will cause a big loss ofmaterial and even peoples life.
Shanghai-China
Highland Towers-
Malaysia
Overturning
residential building15
-
8/18/2019 Chapter 1 Part 2 Substructures
16/139
Soil Quality Is The Key uilding rely on soil beneath to stay put. /f the soil under the house moves up!
down! or sideway! the house is in trouble. The soil pro"le may be varies as we move across from side to side! and when
we dig deeper downward. )trong soil wea% soil type range from
The following are the di8erent types of soils on which foundations are constructed9 Soft soils This soil is compressible and yields when loaded. amples are
clayey soil and loam. )mall buildings or ordinary structures can be built onthese types of soils.
Sreading soils These are noncohesive soils. amples of this type of soilare sand and gravel.
!ard or roc"y soils These are incompressible and strong soils. They canwithstand heavy loads without yielding. +ultistoried buildings and waterreservoirs are designed on such soils.
Bedroc-gravel-course sand-!ine sand-clay-silt-organic "aterial#STRONG WEAK
16
-
8/18/2019 Chapter 1 Part 2 Substructures
17/139
Types of oundation
17
-
8/18/2019 Chapter 1 Part 2 Substructures
18/139
SH$%%OW
FO&'D$T(O'S
1#
-
8/18/2019 Chapter 1 Part 2 Substructures
19/139
)trip oundation +ost suitable! economical type of
foundation for small building oncompact soil.
)trip foundation should bebuild:construct on soil with highbearing capacity.
This type of foundation is also %nownas wall foundation or continues spreadfooting foundation.
onsist of continuous strip of steelreinforced concrete! from centrally
under load bearing walls. The continuous strip serves as a level
base on which the wall is build and thewidth is design to capable to supportthe load without undue compaction.
1*
-
8/18/2019 Chapter 1 Part 2 Substructures
20/139
)trip oundationThe greater the bearing capacity of the
subsoil, the less the width of thefoundation.
;idth of strip foundations depends on
the bearing capacity of the subsoil andthe load on the foundations.
-
8/18/2019 Chapter 1 Part 2 Substructures
21/139
haracteristic of )pread:)tripootings
(ow ostase of constructionor smallmedium si=e structures with
moderategood soil.or large structures with eceptionally goodsoil or shallow bedroc%.
)pread:strip footing may be built in di8erentshapes and si=es to accommodate individualneeds.
21
-
8/18/2019 Chapter 1 Part 2 Substructures
22/139
Tyes of sread footings #ased onsi$e and shae
No Types of Spread Footings Applicable
1 Square for a single centrally-located column
2 Rectangular when large moment load are present
3 Circular for light standards, flagpoles etc
4 Continuous for bearing walls
!wall"strip footings#
$ Combined when columns are close together
% Ring for walls of abo&e-ground circular storage tan's
( Strap !cantile&er footing# when &ery close to a property line"other structure
22
-
8/18/2019 Chapter 1 Part 2 Substructures
23/139
23
-
8/18/2019 Chapter 1 Part 2 Substructures
24/139
In both
situations shown
the thickness (T)
of the foundation
should be eualto ! o" #$%&&'
whichee" is
"eate"
T*! o" #$%&&
(whichee"
"eate") Foundation width
should not be less than
the appropriate
di"ension in Table )#*
Foundation width should benot less than the
appropriate di"ensions in
Table )#* plus o!!set
di"ensions $+ and $*
T T
24
-
8/18/2019 Chapter 1 Part 2 Substructures
25/139
The !oundation !ails
where tension is
e,erted on the concrete
(! is greater than T. then the
!oundation "ay shear at /01
reducing the width o! the
!oundation and bearing area#
Following the shear !ailure. theload is concentrated on a s"aller
area. the ground "ay consolidate
under the increased load
Shear !ailure angle
/01
T
25
-
8/18/2019 Chapter 1 Part 2 Substructures
26/139
ST%&&IN' ST(I&FO)ND*TIONS
;hen strip foundationused in sloping sitesstepped the foundation.
The full thic%ness of theupper foundation shouldoverlap twice twice theheight of the step$>?2T&! or 3-- mmwhichever is greater.
The bric%wor% andbloc%wor% on the top ofthe foundation should tiein at the step to avoid theneeds of cutting
bric%s:bloc%s and to avoidthe possibility of reducingthe stability of the wall.
26
-
8/18/2019 Chapter 1 Part 2 Substructures
27/139
+ID% ST(I& FO)ND*TIONS
;ide strip foundations distribute loads over a larger
area and reducing the load per unit area on the ground.;ider strip foundation is most suitable for subsoil with
poor bearing capacity such as soft sandy clays.;idening and deepening the concrete foundation $to
ensure the foundation does not shear& @ uneconomical.lternativelyform a strip of steelreinforce concrete for
safeeconomical wide strip foundation $"gure #&.
Fiu"e +2 Wide Strip
Foundation
27
-
8/18/2019 Chapter 1 Part 2 Substructures
28/139
N*((O+ ST(I&FO)ND*TIONS
lso %nown as trench "ll:deep stripfoundation.
)uitable for good bearing soil withseasonal volume change soil:clay e.g9sti8 clay.
The base of narrow:deep strip will
etend up to a depth where the clay soilis una8ected by seasonal changes inmoisture content.
5-mm thic% compressible sheetmaterial may needed to prevent lateralpressure to the sides of the foundation$saturated and dries out condition causeepansion and contraction of soil at theeternal face of the foundation&
2#
-
8/18/2019 Chapter 1 Part 2 Substructures
29/139
(ectangular SreadFootings
/t have plan dimension of B x L! where L is the longestdimension.
These are useful when obstructions prevent construction ofa s'uare footing with a suciently large base area andwhen large moment loads are present.
2*
-
8/18/2019 Chapter 1 Part 2 Substructures
30/139
Circular Sread Footings
This foundation areround in plan view.
These are morefre'uently used asfoundation for lightstandard! Aagpoles! andpower transmission line.
/f these foundation
etend to a large depth!they may be have moreli%e a deep foundation.
3-
-
8/18/2019 Chapter 1 Part 2 Substructures
31/139
Continuous SreadFootings This type of foundation is also %nown as wall
foundation or strip foundation.
/t uses is to support bearing wall.
31
-
8/18/2019 Chapter 1 Part 2 Substructures
32/139
(ing Sread Footings
This footing are continuousfooting that been wrappedinto a circle.
This type of footing is
commonly used to support thewalls of aboveground circularstorage tan%s.
32
-
8/18/2019 Chapter 1 Part 2 Substructures
33/139
orces pushingdown must e'ualthe forces pushingup %Q)I,IB(I)M
33
-
8/18/2019 Chapter 1 Part 2 Substructures
34/139
Beave
)ubside
/f the forces pushing up isgreater than the forcespushing down the building will
be pushed upwards @ !%*-%
/f forces pushing down isgreater than the forces
pushing up the building willsin% @ S)BSID%NC%
34
-
8/18/2019 Chapter 1 Part 2 Substructures
35/139
0roblems if the rules arenot followed
$0CT&
The load spreads atabout 4-- through thefoundation
35
,oads *cting on the
-
8/18/2019 Chapter 1 Part 2 Substructures
36/139
,oads *cting on the
Foundation The foundation has to bear more than Dustthe load of the superstructure.
load can be de"ned as anything! whicheerts pressure or thrust on a structure.
The following are the di8erent types ofloads that act on the building foundation9
,i.e ,oad /Q" 0 live load or imposedload is a movable! temporary ortransferable load. This can includemoving vehicles! people wal%ing orchildren Dumping.
Dead ,oad /'" 01 This load is permanentand immovable. /t is the non transferableload of the structure itself.
+ind ,oad /+" 0 This load is applicablewhen the structure is tall.
Sno2 ,oad This load is consideredwhen the structure is situated in snowy!hilly areas.
36
-
8/18/2019 Chapter 1 Part 2 Substructures
37/139
3oc or soil Typical bearing value4'5"*6
Massive igneousbedroc
Sandstone
Shales and "udstone
7ravel. sand and gravel.co"pact
Mediu" dense sand
%oose !ine sand
Hard clay
Mediu" clay
So!t Clay
+8.888
*.888 to /.888
988 to *.888
988
+88 to )88
%ess than +88
)88 to 988+88 to )88
%ess than :0
Typical allowable bearing values37
-
8/18/2019 Chapter 1 Part 2 Substructures
38/139
3#
-
8/18/2019 Chapter 1 Part 2 Substructures
39/139
&*DFO)ND*TIONFOOTIN'
)imilar to continuousfootings accept for they areusually lain under a singlepier:column.
0ad foundation spread theload out $in a s'uare& withthe column:pier sitting inthe middle of the s'uare.
an also be designed forloads of the walls and thebuildings are transferred
through ground beams thatrest on the pad foundations. The pad foundations the will
transfer the loads to a lowerlevel where soil of sucientload bearing strata eist.
3*
-
8/18/2019 Chapter 1 Part 2 Substructures
40/139
onstruction se'uence of pad foundation
Mared out and e,cavate
ground to correct level#
;,cavation level should up
to good load bearing
strata#
The clean and leveled
ground then poured with08"" thicness lean
concrete#
For"wor !or the !ooting
installed at the correct
position
(nstall rein!orce"ent according
to construction detailing
$!ter pad !ooting detailing
inspected and approved than
concrete can be poured and
leave the !oundation to dry
4curing process6
4-
-
8/18/2019 Chapter 1 Part 2 Substructures
41/139
&*DFO)ND*TIONFOOTIN'
The advantage of thissystem of foundation isthat poc%ets of tippedstone or bric% and
concrete rubble that wouldobstruct bored pile may beremoved as the pits areecavated.
The nature of subsoil alsomay be eamined as thepits are dug to select alevel of sound subsoil.
41
-
8/18/2019 Chapter 1 Part 2 Substructures
42/139
S4uare Footings
42
-
8/18/2019 Chapter 1 Part 2 Substructures
43/139
Co5#ined FootingFoundation
/n this type! the two wallsor columns of asuperstructure are providedwith a single combined
footing. This is designed so that the
center of gravity of thesupporting area is inproportion to the center of
gravity of the tow columnloads.
These can be rectangular ortrape=oidal in shape.
These are usefull whencolumns are located tooclose together for each tohave its own footing.
43
-
8/18/2019 Chapter 1 Part 2 Substructures
44/139
(*FT FO)ND*TION
Eepending on its positionraft foundation also %nownas +at foundation inAoating position.
)ometimes also called as
loating oundation.Fsed where heavilyconstructed loads are to bedistributed over a largesurface area.
/t is used where the soil ismarshy! clayey or soft!with wea% bearingcapacity.
44
-
8/18/2019 Chapter 1 Part 2 Substructures
45/139
This consists ofreinforced concrete
slabs covering theentire area ofconstruction! li%e aAoor.
lways made ofreinforcedconcrete.
SI,!-E RAFT FO.N/ATION
RAFT FO.N/ATION
45
-
8/18/2019 Chapter 1 Part 2 Substructures
46/139
(*FT FO)ND*TION
/f groundpressures areli%ely to be
ecessive atdi8erent seasons!reinforcementmay be re'uiredthis is %nown asfa#ric when in
sheet mesh form.
REINFOR0E/ RAFT FO.N/ATION
46
-
8/18/2019 Chapter 1 Part 2 Substructures
47/139
0onditions fo" Raft1,at Foundations-Structural loads re
-
8/18/2019 Chapter 1 Part 2 Substructures
48/139
D%%P F(D*
4#
-
8/18/2019 Chapter 1 Part 2 Substructures
49/139
DEEP FOUNDATIONDEEP FOUNDATION
0easons why Deep Foundation
4*
-
8/18/2019 Chapter 1 Part 2 Substructures
50/139
ain $oponents of Deep Foundation
5-
-
8/18/2019 Chapter 1 Part 2 Substructures
51/139
DEEP FOUNDATIONPiles are long and slender e!ers which transfer
the load to deeper soil or roc" of high !earingcapacity a)oiding shallow soil of low !earingcapacity.
he ain types of aterials used for deep pilesare wood, steel and concrete.
Piles ade fro these aterials are dri)en, drilledor 3ac"ed into the ground and connected to pilecaps.
ain functions of a pile+i. to transit a foundation load to a solid ground
ii. to resist )ertical, lateral and uplift load
51
-
8/18/2019 Chapter 1 Part 2 Substructures
52/139
52
Factors (n!luencing
-
8/18/2019 Chapter 1 Part 2 Substructures
53/139
g
The Choice o! ile
%ocation and
Type o! Structures7round Conditions Durability Cost
7round containing
Boulders-
clay with
ground heave
%oose water
bearing sand
Concrete
Steel
Ti"ber
(nstallation costOver water
On %and
'ot causing vibration
to e,isting5nearby
Structures-
Heavy Structure
;,isting Structure
&nder-rea"ed bases
"aterials
ti"e
Test load
Supervision
Organi>ation.
overhead and etc#53
-
8/18/2019 Chapter 1 Part 2 Substructures
54/139
Factors nfluencing the $hoice of Pile
$cati# a#% t&pe ! structures
For structures o)er water, such as whar)es and 3etties,dri)en piles or dri)en cast-in-place piles 4in which theshell reains in place' are the ost suita!le.
n land, dri)en cast-in-place types are usually thecheapest for oderate loadings.t is necessary for piles to !e installed without causing
any significant ground hea)e or )i!rations !ecause oftheir pro&iity to e&isting structures, the !ored cast-
in-place pile is the ost suita!le.For hea)y structures e&erting large foundation loads,large-diaeter !ored piles are usually the osteconoical.
5ac"ed piles are suita!le for underpinning e&isting
structures.54
-
8/18/2019 Chapter 1 Part 2 Substructures
55/139
Factors nfluencing the $hoice of Pile
'ru#% c#%iti#s
Dri)en piles cannot !e used econoically in groundcontaining !oulders 4large roc"s', or in clays when
ground hea)e would !e detriental.Bored piles would not !e suita!le in loose water-
!earing sand, and under-reaed !ases cannot !eused in cohesion less soils since they are suscepti!leto collapse !efore the concrete can !e placed.
55
-
8/18/2019 Chapter 1 Part 2 Substructures
56/139
Factors nfluencing the $hoice of Pile
Durabi(it&
ost iportant criteria especially in the choice ofaterial. For e&aple, concrete piles are usually
used in arine conditions since steel piles aresuscepti!le to corrosion in arine conditions .
ti!er piles is not the ost suita!le type underarine conditions !ecause it can !e attac"ed !y
!oring olluscs .n land, concrete piles are not the !est choice,
especially where the soil contains sulphates or otherharful su!stances.
56
-
8/18/2019 Chapter 1 Part 2 Substructures
57/139
Factors nfluencing the $hoice of Pile
$ost
$onsidera!le iportant decision o)er the choice of pile.
he o)erall cost of installing piles includes: the actual cost of the aterial,the ties re6uired for piling in the construction plan,test loading,cost of the engineer to o)ersee installation and
loadingcost of organisation and o)erheads incurred !etween
the tie of initial site clearance and the tie whenconstruction of the superstructure can proceed.
57
-
8/18/2019 Chapter 1 Part 2 Substructures
58/139
$lassification of Pile 7ith 0espect to 8oadransission and Functional Beha)ior
nd bearingpiles $point
bearing piles&riction piles
$cohesion piles &ombination of
friction andcohesion piles
5#
-
8/18/2019 Chapter 1 Part 2 Substructures
59/139
%D B%*09 P8%
5*
-
8/18/2019 Chapter 1 Part 2 Substructures
60/139
%nd !earing piles ypical end-!earing piles are dri)en
through )ery soft soil, such as a loose silt-!earing stratu underlying !ycopressi!le strata.
his pile acts on the !asic concept ofdigging through the top soil 4relati)elywea"' to an underlying firer roc" toanchor the foundation.
he piles transfer their load on to a firstratu located at a considera!le depth!elow the !ase of the structure.
6-
-
8/18/2019 Chapter 1 Part 2 Substructures
61/139
%nd !earing piles
his pile !eha)es as an ordinary colun. n wea" soil, this pile will
not fail !y !uc"ling
61
-
8/18/2019 Chapter 1 Part 2 Substructures
62/139
%nd !earing piles-cast in place
62
-
8/18/2019 Chapter 1 Part 2 Substructures
63/139
%nd !earing piles - dri)en or 3ac"ing40.$ or Steel Pile'
63
-
8/18/2019 Chapter 1 Part 2 Substructures
64/139
Piling 0ig
64
-
8/18/2019 Chapter 1 Part 2 Substructures
65/139
Pile Dri)ing65
-
8/18/2019 Chapter 1 Part 2 Substructures
66/139
F0$ P8%
66
l
-
8/18/2019 Chapter 1 Part 2 Substructures
67/139
Friction piles
Friction piles, also "nown asfloating pile foundations, $oonly used in
construction to pro)ideunderground support for!uildings, !ridges, doc"sand other structures.
hey are often used whenend-!earing piles are notsuita!le.
Friction piles relyspecifically on the frictioncreated !etween the soiland the surface of the pile
aterial in order to pro)idesta!ility. he co!ination of friction
and adhesion with the soilcauses the to stay inplace.
67
F i ti il
-
8/18/2019 Chapter 1 Part 2 Substructures
68/139
Friction piles
he load is transferred tothe ad3oining soil !y friction!etween the pile and thesurrounding soil.
he load is transferreddownward and laterally tothe soil.
n order for friction pilesto !e effecti)e, the soilsurrounding the area ust!e fairly unifor in typeand density.
For ore cople&situations, construction
copanies soeties relyon a co!ination of frictionand end-!earing piles.
6#
-
8/18/2019 Chapter 1 Part 2 Substructures
69/139
Friction Pile ypes
0ast2in2situ
/"ien
lace"ent
o! pile
(nstallation
o! ile3epetition
process
6*
-
8/18/2019 Chapter 1 Part 2 Substructures
70/139
SP( P8%
7-
S Pil
-
8/18/2019 Chapter 1 Part 2 Substructures
71/139
Spun PileStandard $haracteristics Pre-stressed concrete spun pile 4cast in the factory' and deli)er
to site for installation. Si;e : 2, ? and 12 4ypical'
Structural $apacity : @
-
8/18/2019 Chapter 1 Part 2 Substructures
72/139
Spun Pile
72
-
8/18/2019 Chapter 1 Part 2 Substructures
73/139
Spun Piles Es. 0$ S6uare Piles
Spun Piles ha)e Better Bending 0esistanceigher *&ial $apacity Better anufacturing Guality *!le to Sustain igher Dri)ing
Stressesigher ensile $apacity %asier to $hec" ntegrity of Pile
Siilar cost as 0$ S6uare Piles withhigher pile integrity
73
d A D d f P l
-
8/18/2019 Chapter 1 Part 2 Substructures
74/139
*d)antages A Disad)antages of Spun Pile
No Advantages Disadvantages
1 Best suited for use as friction piles that Expensive to splice and cut
don't meet refusal during driving
(refusal: pile can't be driven any further so
it becomes necessary to cut off the portion!
" Best suited for toe#bearing piles $here the Difficult to cut
re%uired length is uniform and predictable
& ess expensive than steel piles usceptible to damage during handling
or driving
) *ave a large load capacity Not suited for hard driving conditions
74
-
8/18/2019 Chapter 1 Part 2 Substructures
75/139
B0% P8%
75
d l
-
8/18/2019 Chapter 1 Part 2 Substructures
76/139
Bored pilesH Foundation structure ade of
reinforced concrete on site.H (sed to carry hea)y loads !ytransitting the load to a sta!le soilstrata.
H Earies in diaeter and depth.H Diension )aries fro @
-
8/18/2019 Chapter 1 Part 2 Substructures
77/139
Bored Pile $onstruction
H Bored piles is constructed!y first drilling a hole inthe ground until acopetent load !earinglayer is reached.
H nce achie)ed, areinforceent steel cageis lowered into the drilledhole and the hole is filledwith concrete.
H t is also "nown as cast inplace piles)
77
B d il
-
8/18/2019 Chapter 1 Part 2 Substructures
78/139
Bored piles igh fle&i!ility and are widely used in
deep foundation for :- high rise !uildings, 3etties, !ridge foundation and as )ertical retaining structures li"e a
retaining wall or sheet piles wall. 4n thiscase the !ored piles is "nown ascontiguous !ored pile wall'.
Designed either as a point !earing pilesor friction piles.
f copetent load !earing layer li"e!ed roc" is present, then the !oredpiles will !e designed as an end-!earingpile. his eans that the load carrying
capacity of the piles is ainly deri)edfro the !earing capacity of the roc"layer at the toe of the pile.
7#
Bored Piles
-
8/18/2019 Chapter 1 Part 2 Substructures
79/139
Bored Piles
Bored pile-single pile - pile groups.
7*
-
8/18/2019 Chapter 1 Part 2 Substructures
80/139
can !e inclined to a certain angle.*ngle !ored piles also "nown asra"ed piles 4found in structures thatre6uires resistance to hori;ontalload li"e in a retaining wall or !ridgeand piers foundation'.
7hen !ored piles are
constructed close to oneanother or o)erlapping slightly,this is "nown as contiguous!ored piles wall or secant pileswall.
#-
Sta#%ar% Bre% Pi(es Characteristics
Si @
-
8/18/2019 Chapter 1 Part 2 Substructures
81/139
Si;e : @
-
8/18/2019 Chapter 1 Part 2 Substructures
82/139
#2
-
8/18/2019 Chapter 1 Part 2 Substructures
83/139
#3
-
8/18/2019 Chapter 1 Part 2 Substructures
84/139
#4
-
8/18/2019 Chapter 1 Part 2 Substructures
85/139
#5
-
8/18/2019 Chapter 1 Part 2 Substructures
86/139
#6
-
8/18/2019 Chapter 1 Part 2 Substructures
87/139
#7
-
8/18/2019 Chapter 1 Part 2 Substructures
88/139
##
-
8/18/2019 Chapter 1 Part 2 Substructures
89/139
#*
-
8/18/2019 Chapter 1 Part 2 Substructures
90/139
*-
-
8/18/2019 Chapter 1 Part 2 Substructures
91/139
*1
*d t A Di d t
-
8/18/2019 Chapter 1 Part 2 Substructures
92/139
*d)antages A Disad)antagesBore Pile
No Adantaes /isadantaes
# -ess costs of &obili3in and de&obili3in a d"ill "i /e4endent on cont"acto"5s skills
6 -ess noise and ib"ation -owe" unit end bea"in ca4acit7
8 Soils e9caated can be obse"ed and classified E94ensie fo" full2scale load test
du"in d"illin
: Si3e of shafts can easil7 be chaned du"in const;
$ 0an 4enet"ate soils with cobbles' boulde"s and
&an7 t74es of bed"ock
< !ossible to su44o"t each colu&n with one la"e
shaft (no 4ile ca4)
*2
-
8/18/2019 Chapter 1 Part 2 Substructures
93/139
$0P8%
*3
icropiles
Si;e : 1== to #
-
8/18/2019 Chapter 1 Part 2 Substructures
94/139
Si;e : 1== to #
-
8/18/2019 Chapter 1 Part 2 Substructures
95/139
icropiles
icropiles also "nown ini piles.*pplication also for foundations of a wide )ariety ofconstruction pro3ects such as highways, !ridges ande)en transission towers.
$an !e installed at )arying angles i.e. fro )ertical to
o!tuse 4angle !etween ?=-1= degree incline'.ighly capa!le of resisting !oth lateral and a&ial loadsdue to the fact that they are ade of steel with)arying diaeters of !etween I= to 2== .
Sheer a!ility to pro)ide a co!ination of !oth tensile
and copressi)e resistance, icropiles tend to !e6uite useful where there is a need for resistance touplift.
Eery little or no )i!ration at all.
*5
echnological process of carrying
-
8/18/2019 Chapter 1 Part 2 Substructures
96/139
g p y gout icropiles
2a& reali=ation ofa boreholewith the rotarytechnology
2b& pulling outdrilling toolsand "lling the
hole with grout2c& setting areinforcementthic%walledsteel pipe
2d& grouting ofthe micropile
root part2e& "nished
micropile
Pressure+,rute% "icrpi(es c#structi#
*6
-
8/18/2019 Chapter 1 Part 2 Substructures
97/139
E9a&4les of unde"4innins of e9istin
st"uctu"es with the use of &ic"o4ile s4ace4ie"s o" indiidual &ic"o4iles
Secu"in oe"bu"dens of unde""ound wo"ks
(tunnels' alle"ies) with the use of a
&ic"o4ile u&b"ella
Carrying out pipe "icropiles to protect the driven
tunnel calotte. the 'ew Connection in rague*7
-
8/18/2019 Chapter 1 Part 2 Substructures
98/139
*#
ast insitu micropile
-
8/18/2019 Chapter 1 Part 2 Substructures
99/139
as s u c op econstruction
**
! /B " P l
-
8/18/2019 Chapter 1 Part 2 Substructures
100/139
i!er/Ba"au Pile
i!er is a hugely capa!le ci)ilengineering aterial, with theadditional ad)antage of !eingsustaina!le.
rees, in particular conifers, a"enatural piles.
i!er foundations ay !e particularlysuita!le for countryside structuressuch as !ridges, forest chalets andacti)ity centres, as well as post-and-!ea ti!er !uildings in waterfront or
flood prone locations. Preser)ati)e treated softwood or
dura!le hardwood ti!er can !e usedfor the construction of retaining walls,!an" seats, and for foundation padsand footings.1--
! /B " P l
-
8/18/2019 Chapter 1 Part 2 Substructures
101/139
i!er/Ba"au Pile For any structures, ti!er piles are a highly suita!le choice of
foundation, gi)en appropriate ground conditions. hey are econoical, easy to transport, handle, cut to length and
wor" with on site+ and particularly suited for locations with accessdifficulties, or where e&ca)ations and the deli)ery of concretewould pose pro!les.
Short, dri)en ti!er piles can !e the solution for foundations inground with a high water ta!le, and where fir strata e&ists !elowsurface aterial of loose sand, soft clays, or organic soils.
1-1
i ! /B " Pil
-
8/18/2019 Chapter 1 Part 2 Substructures
102/139
i!er/Ba"au Pile n deep silt deposits, where the capacity of the pile is deterined
!y shaft friction, ti!er piles are especially suita!le !eing taperedand easy to splice.
i!er piles are suita!le to !e used !elow the water ta!le, wherethey ha)e pro)ed practically in)ulnera!le to decay, and e&tended tothe surface using concrete sections.
hey are resistant to acidic and al"aline soils, and soils with highsulphate or free car!on dio&ide content.
i!er piles can also !e dri)en for ground ipro)eent, to densityloose granular soils.
For the decay reason-treated with preser)ati)es such as creosote
oil which ipregnated into the wood 4pre)enting dry-rotting andagainst daage fro ost anial and plant attac"'
1-2
i ! /B " Pil
-
8/18/2019 Chapter 1 Part 2 Substructures
103/139
i!er/Ba"au Pile he installation of ti!er piles is a process that in)ol)es dropping a
weight on top of the pile in order to dri)e the pile into the ground. i!er piles ha)e !een used for centuries to support an-ade
structures. he e6uipent that is used to install ti!er piles includes a crane,
a !oo, a set of leads, a haer, a helet, a pile gate, pile on"ey,
and pile 4see Figure'.
1-3
*d)antages A Disad)antages
-
8/18/2019 Chapter 1 Part 2 Substructures
104/139
g gBa"au pile
No Advantages Disadvantages
1 Low construction cost Medium axial loads 1!! " #!! $N%
& 'sed as waterfront structures Susceptible to decay
( For lig)t driving conditions Susceptible to damage w)en driving
in loose sands and soft to medium clays%
1-4
Pili h i
-
8/18/2019 Chapter 1 Part 2 Substructures
105/139
Piling echni6ues
Eamage during driving can becontrolled by using propertechni'ue.
mong the soultions are9GFsing lightweight hammersGFsing steel bands near butt
GFsing a steel shoe on the toeG0redrilling
1-5
D ill d % i t
-
8/18/2019 Chapter 1 Part 2 Substructures
106/139
Drilled %6uipents
Dri((i#, Ri,sruc"-ounted
drilling rigFor usual
shaft,dJ.2@
Speciali;edrigs
*-ShapedFrae 0igs
1-6
-
8/18/2019 Chapter 1 Part 2 Substructures
107/139
Dri((i#, T(s
he heli&-shaped flight auger4ost coon used') %ffecti)e in ost sols and
soft roc"s *ugers with hardened teeth
and pilot stingers
) %ffecti)e in hardpan oroderately hard roc"
Spiral-shaped rooting tools) elp loosen co!!les and
!oulders
1-7
-
8/18/2019 Chapter 1 Part 2 Substructures
108/139
Buc"et augers) o collect cuttings in a cylindrical
!uc"et) (sed in running sands
Belling !uc"ets) o enlarge the !otto of the shaft
4!ells or under reas' $ore !arrels
) o cut a circular slot creating areo)a!le core
) (sed in hard roc" ulti-roller percussion !its
) o cut through hard roc" $leanout !uc"ets
) o reo)e final cuttings fro hole
Belling bucet
Bucet augers
1-#
D ill d h i
-
8/18/2019 Chapter 1 Part 2 Substructures
109/139
Drilled echni6ues
Erilling in irm )oilsFsing dry method $openhole method&+ost common used9 simple! economy and
good reability
)teps9Boles usually advance using conventional Aightauger
Boles remain open without any special supporthec% the open hole for cleanliness and
alignment/nsert steel reinforcing cage0our the concrete
1-*
-
8/18/2019 Chapter 1 Part 2 Substructures
110/139
11-
-
8/18/2019 Chapter 1 Part 2 Substructures
111/139
Drilling in $a)ing 4$a)e-in' or S6uee;ing Soils
$a)ing:he side of a hole which is collapse !efore or during concrete
placeent.(sually in clean sands !elow the groundwater ta!le.
S6uee;ing:
he sides of hole !ulging inward during or after drilling(sually in soft clays and silts or highly organic soils.
ost coon techni6ues:(sing casingDrilling fluid 4slurry ethod' using !entonite clay or
attapulgite clay.
111
-
8/18/2019 Chapter 1 Part 2 Substructures
112/139
P8% $*P
112
P8% $*P
-
8/18/2019 Chapter 1 Part 2 Substructures
113/139
Pi(e Cap 4BS ==@', Ka pile cap is
defined as a concrete !loc" cast onthe head of a pile, or a group of piles,to transit the load fro thestructure to the pile or group ofpilesL.
H Pile cap transfers the load for thestructures to a pile / pile group, thenthe load further transfers to frosoil.
HPile caps are thus incorporated in
order to tie the pile heads together sothat indi)idual pile o)eent andsettleent is greatly reduced. hesta!ility of the pile group is greatlyincreased.
P8% $*P
113
-
8/18/2019 Chapter 1 Part 2 Substructures
114/139
114
Foundations relying on dri)en
-
8/18/2019 Chapter 1 Part 2 Substructures
115/139
Foundations relying on dri)enpiles often ha)e groups of pilesconnected !y a pi(e cap 4a
large concrete !loc" into whichthe heads of the piles aree!edded' to distri!ute loadswhich are larger than one pilecan !ear.
Pile caps and isolated piles aretypically connected with ,ra%ebea"s to tie the foundationeleents together+ lighterstructural eleents !ear on
the grade !eas while hea)iereleents !ear directly on thepile cap.
115
Pile *rrangeent !elow pile cap
-
8/18/2019 Chapter 1 Part 2 Substructures
116/139
Pile *rrangeent !elow pile cap
116
Pile cap
-
8/18/2019 Chapter 1 Part 2 Substructures
117/139
Pile cap
Function:o distri!ute the structural loads to the piles.o tie the piles together so they can act as a unit.
o laterally sta!ilise indi)idual piles thus increasing o)erallsta!ility of the group
o pro)ide the necessary co!ined resistance to stresses setup !y the superstructure and/or ground o)eent
117
-
8/18/2019 Chapter 1 Part 2 Substructures
118/139
$8( S(P
11#
$olun Stup
-
8/18/2019 Chapter 1 Part 2 Substructures
119/139
$olun Stup he stup is the siplest and ost failiar
footing used for the )ertical support and thetransfer of !uilding loads to the foundation. Stups are used to support ti!er-fraed
houses for which they are currently the ostcost effecti)e.
hree types of aterials are coonly used forstups: ti!er concrete steel.
Stups ust ha)e a concrete or ti!er footingplaced underneath the !ase of the stup. his isto spread the load transferred to the stup
fro the !uilding. his support !eneath thestup is called a MpadM or MsoleplateM. (sually concrete stups are pro)ided with
concrete pads poured i# situ on the site. i!erstups are pro)ided with ti!er soleplates.
11*
-
8/18/2019 Chapter 1 Part 2 Substructures
120/139
90(D B%*
12-
2 1 90(D B%* *D S8*B
-
8/18/2019 Chapter 1 Part 2 Substructures
121/139
2.1 90(D B%* *D S8*B Beas and sla! are norally naed !y
its location. 9round !ea refers to the structure of
!ea located on the ground. 9round Beas are designed to support
!ric"/!loc"wor" or to for a peranent
shutter to the edge of in-situ concretefloor sla!.
he aount of reinforceentintroduced into the design will !e usedto suit specific loading re6uireents
and the !eas can !e designed towithstand any hea)e forces with the useof )oid foring or copressi!leaterials.
121
rdinary 9round Bea
-
8/18/2019 Chapter 1 Part 2 Substructures
122/139
rdinary 9round Bea
his type of ground !ea is the ostused in !uilding construction.
t is the !ea which !oth its ends aretied up at the colun and lying !etween
the two colun. he !ea fi&es and holds fitly the
coluns in order to sta!ili;e it. n addition, it also acts to !ear all the
loads coe fro the wall which
constructed parallel with the !ea.
122
0D*0N 90(D B%*
-
8/18/2019 Chapter 1 Part 2 Substructures
123/139
0D*0N 90(D B%*
123
* ground !ea norallyshould consist of followingites+0einforceents,$oncrete,8in"ers
he reinforceents can !eplaced at center of that!ea.
he si;es of ainreinforceent playiportant role in deterinethe strength of a !ea.
9round !ea usually doesnot ha)e secondary !ea,only has priary !ea.
0D*0N 90(D B%*
-
8/18/2019 Chapter 1 Part 2 Substructures
124/139
0D*0N 90(D B%*
124
90(D $*8%E%0 B%*
-
8/18/2019 Chapter 1 Part 2 Substructures
125/139
90(D $*8%E%0 B%*
125
he functions of groundcantile)er !ea are alost sae!ut it cannot !ear the loadingsuch the ordinary !ea. his is!ecause, one end of that !eais not holding !y any structure.*s a result, it does not achie)esthe strength li"e the ordinary!ea
?he cantile)er !ea is sae as the !ea e&plained !efore !ut onlyone end of cantile)er !ea is tied up at the colun stup. heother end is free without 3oint with any colun.?he cantile)er !ea usually used for e&ternal structure such as!ea for corridor and also partition wall outside the !uilding.
Bea $onstruction ethod
-
8/18/2019 Chapter 1 Part 2 Substructures
126/139
Bea $onstruction ethod
126
he ground !ea construction will !e started after acolun stup has finish. 4*fter the colun stup hasingrained in foundation and has corpulent on le)el aswanted'.
Bea forwor" will put and pointed sta"e set in theground with tidy so that loo" tough and strength.
Strength of forwor" is iportant to ensure thatforwor" not e&pand when a concrete will instill. fforwor" not good, its will gi)e a pro!le and theconstruction wor" ha)e uch tie.
*fter that, lin" concrete is lain out on ground surfaceinto the forwor". he reinforceents will !e putted
with spacer !loc" on !elow and !eside reinforceent.Purpose that putted the spacer !loc" is to protect thereinforceent for a)oid fro rust
-
8/18/2019 Chapter 1 Part 2 Substructures
127/139
127
R)C) BEA- CONSTRUCTION PROCESS
9round Bea
-
8/18/2019 Chapter 1 Part 2 Substructures
128/139
9round Beahe ground !ea construction procedure 41= steps'+
1. clearing the ground.2. he span !etween the coluns or piers is raed and copacted.#. * !linding layer is done with 6uarry dust.@. he colun or pier reinforceents should !e left a foot high to 3oin
with the !ea.. nce ready, they are carried and laid o)er the coluns and !linding.I. he reinforceent is laid straight with spacer !loc"s put at the
!otto.. nce the !ea steel is in place, for wor" is erected to the sides.
hese ust !e fired into the ground and ade )ery tight. his willpre)ent the escape of the ceent slurry when )i!rating.
?.*fter the for wor" is coplete, concrete is prepared and pouredinto the fors. he process continues while )i!rating to ensure theconcrete is well !onded with the steel.
1=.he top is taped to !e sooth. he fors are reo)ed after se)endays while curing.
12#
-
8/18/2019 Chapter 1 Part 2 Substructures
129/139
90(D S8*B
12*
9round Sla!
-
8/18/2019 Chapter 1 Part 2 Substructures
130/139
9round Sla!
13-
n construction, sla! can !e design in two conditions.
N#+suspe#%e%s(ab
Suspe#%e% s(ab
9round Sla!
-
8/18/2019 Chapter 1 Part 2 Substructures
131/139
9round Sla!
131
9round Sla!
-
8/18/2019 Chapter 1 Part 2 Substructures
132/139
9round Sla! Function of ground sla!:
o support colun and stupo recei)ed the load fro the !uilding o reduce the pressure on the colun and stup he ain !ase of construction to ensure that the
construction will done well$reate the easier 3o! on floor finishes
he construction of a solid ground sla! floorshould includes:
ardcoreBinding$oncrete !ed or sla!
132
9round Sla!
-
8/18/2019 Chapter 1 Part 2 Substructures
133/139
9round Sla!
ardcore he purpose of hardcore is to fill in any sall poc"ets that ha)e
for during o)er site e&ca)ation, to pro)ide fir !ase on which toplace a concrete !ad and to help spread any point loads o)er the
greater area. t also acts against capillary action of oisture withinthe soil. ardcore is usually laid in 1==-1
-
8/18/2019 Chapter 1 Part 2 Substructures
134/139
9round Sla!
Binding his is used to e)en off the surface of hardcore if a dap-
proof e!rane 4DP' is to !e place under the concrete !edor if a reinforced concrete !ed is specified.
First, it will pre)ent the dap-proof e!rane fro !eingpunctured !y the hardcore and, second, it will pro)ide a truesurface fro which the reinforceent can !e positioned.
Blinding generally consists of a layer of sand 2
-
8/18/2019 Chapter 1 Part 2 Substructures
135/139
9round Sla!
$oncrete !ed (nreinforced or plain in-situ concrete, 1==-1
-
8/18/2019 Chapter 1 Part 2 Substructures
136/139
136
$oncrete 0einforceent esh
9round Sla!
-
8/18/2019 Chapter 1 Part 2 Substructures
137/139
9round Sla!
137
41' Dap Proof e!rane 4DP'7ater penetration is a prie cause of deterioration in
!uilding structures and aterials and the presence ofe&cess oisture encourages the growth of oulds and woodrotting fungi. Because of this, !uilding regulations re6uirethat !uildings are so designed that water neither daagesthe fa!ric nor penetrates to the interior where it ayconstitute a health ha;ard as well as spoiling decorations.
ther aterials needed for ground sla!:
9round Sla!
-
8/18/2019 Chapter 1 Part 2 Substructures
138/139
9round Sla!ther aterials needed for ground sla!:
42' Dap Proof $ourse 4DP$'DP$ is a physical !arrier inserted into the fa!ric of a !uilding
to stop water passing fro one place to another. his can !e on
a hori;ontal plane, stopping water rising up fro the ground !y!eing suc"ed up !y the dry asonry a!o)e, or )ertically to stopwater passing fro the outside of a !uilding, though theasonry, to the inside. DP$Ms ha)e ta"en any fors throughthe ages and one of the earliest fors was to use a layer ofslate in the construction. Slate is still used !ut the lesse&pensi)e plastic )ersion 4 !elow right ' is now ore widelyused.
13#
-
8/18/2019 Chapter 1 Part 2 Substructures
139/139
%D F $*P%0 1
Than% you