Chaibasa Engineering Collegechaibasaengg.edu.in/uploads/teqip/745_CEC_WEB... · Response of a RLC...
Transcript of Chaibasa Engineering Collegechaibasaengg.edu.in/uploads/teqip/745_CEC_WEB... · Response of a RLC...
Chaibasa Engineering College
(Estd.By Govt. of Jharkhand & Run by Techno India under PPP), Jharkand.India.
Procurement Under TEQIP III (Quarter 1, April to June 2018)
1. CEC/EE/ELECTRICAL MACHINE LAB
Procurement Package Items of Procurement
Three Phase Auto Transformer 3 phase , 415V/0-415V/50Hz/15 Amp per Line;Input Voltage range
:340 - 460V Ac, for unbalanced loads 295-465 V AC, 340-460 V AC for
unbalanced loads;Output voltage:400v Ac Setting (Adjustable from 380 -
415V Ac)
Operating Frequency:50+ 3 Hz;Type:Balanced / Unbalanced
Regulation:± 1%;Efficiency:98% at full load;Insulation:Class B
Type of cooling:Air/ Oil cooled;Output voltage Indication:
Digital voltmeter with phase or switch ( up to 50 KVA) Analog voltmeter
for each phase (More than 50 KVA)
Correction rate per phase:Up to ± 70 V/ Sec;Protection:Low / High
Voltage cut-off
Single Phase Auto Transformer 240V/1 Phase/50-60Hz/10A; Input voltage:240/270V; Output Voltage:0-
270V: Single phase enclosed digital metered with Vand A
Rheostat 10Ω,10A(2No.)/60 Ω,5A(2No.)/100 Ω,3A(4No.)/300 Ω,2A(2No.)/1kΩ,
1A(2No.)
Three phase power Quality
Analyser
Input impedance 1 MΩ, 20 pF ;Voltage rating 600 Vrms, CAT III
Volt/Amps/Hertz True-rms voltage (AC+DC): 50.00 V, ± (1 % + 10
counts) True-rms current (AC+DC) 50.00A, ± (1 % + 10 counts)
Frequency 10.0 Hz to 15.0 kHz ± (0.5 % + 2 counts) CF Crest Factor 1.0
to 10.0 ± (5 % + 1 count) Power W, VA, VAR Reactive Power 250 W, ±
(2 % + 6 counts) Total Power 1-phase and 3-phase, 3 25 MW ± (4 % + 4
counts) Fundamental conductor balanced loads Power PF Power Factor
0.00 to 1.00 ± 0.04 DPF Displacement Power Factor 0.00 to 0.25 not
specified 0.25 to 0.90 ± 0.04 0.90 to 1.00 ± 0.03 Hz Frequency
fundamental 40.0 to 70.0 Hz ± (0.5 % + 2 counts)
2. CEC/ECE/OPTICAL COMMUNICATION LAB
Procurement Package Items of Procurement
SPLICING Technique ST Polishing tool 1, Lapping sheets (3 in 1) 10,
Polishing plate 1, Microscope 1, Scribe 1, Crimp tool 1,
Micro Stripper 1, Epoxy 1set, Tissue Paper 50,
Scissors 1, Cleaning Brush 3, Jacket Stripper 1,
Dispenser 1, Magic Tape 1
Epoxy Applicator 1 box, Scale 1, Syringe 10, Torch with
‘AAA’ size batteries (2nos) 1, UV Lamp 1No, Capillaries -
125um ID 25Nos, Glass Sleeves – 1.5mm ID 25Nos,
Aligning Plate 10Nos, Glass Plates 10Nos, UV Bond 1No,
Mechanical Splice 5Nos
Chaibasa Engineering College
(Estd.By Govt. of Jharkhand & Run by Techno India under PPP), Jharkand.India.
Procurement Under TEQIP III (Quarter 1, April to June 2018)
STUDY OF PIN PHOTODIODE Photo detector : Silicon PIN Diode , Responsivity at 880 nm
: 0.4 µA/µW, Optical Input Connector : Self locking cap,
Possible modes of Operation : Zero Bias, Forward Bias,
Reverse Bias & Leakage characteristics , Mode selection :
Switch selectable, Reverse Dark Current : 60 Na,
Detector Capacitance : 4 pF , Bias Control : Potentiometer
Experimental OTDR system ST type optical connector interface. Directional Coupler
1x2, 50/125micron – 1No.
Pulse Generator unit and Software – less than 150ns ON
time with
RS422 interface, 1m ST-ST patch cord – 2Nos. Min 500m
and
individual module spools of bare fiber in length 140,160 of
MMGF in different lengths in open form with Events to
study the OTDR concepts.
LASER diode module:- Wavelength - 660nm (typ.), Max
O/P power - 3mW, Threshold current - 30mA (typ.),
Forward Bias, Collimating lens for adjustable spot size.
Individual module of LD Modulator: Max data rate – up to
34Mbps for NRZ.
Individual module for Optical Receiver: Modulated Optical
I/P - 4Mbps for NRZ.
Optical Power Meter: -Calibrated wavelength –
660nm/850nm, Optical I/p Power: +3dBm to -60dBm,
Accuracy: + 0.2dB, Battery & DC power operation, Optical
Interface for PF (Bare fiber Adapter) & MM GF ( ST
Type).
Optical Power Source:-Optical Source Type – LED,
Wavelength - 880nm, Spectral Width - 100nm, Max optical
o/p: -20dBm, Output Stability: <0.3dB, Optical Connector
- ST type, Attenuation by Coarse & Fine Adjustments.
Modulation: i) Continuous Wave (CW), ii) Internal –
Programmable bit rates from 64 to 2048 Kbps, PRBS, iii)
External Modulation – TTL 0 to 2Mbps.
XYZ-rail
Fiber Spool of 140m & 160m.
LASER detector with free space communication
Pulse generator
OPTICAL FIBER TRAINER KIT Electrical Section:
No. of Channels 12 (64Kbps) channels, including one slot
for 16-bit Marker
Frame Marker Two 8-bit markers in the alternate frame,
user programmable,
can also be set to CCITT standard Coding / Decoding
Manchester Coding / Decoding
Data Rate 768 Kbits/sec, 1.5 Mbits/sec after Manchester
coding Voice PCM channels 2
(2 telephone handsets provided) Voice Coding A-law
Analog Input Voltage 1 Vpp
Analog Input bandwidth 100 KHz Computer to Computer
Thru RS232 interface
data communication (Optional)
Optical Section :
Chaibasa Engineering College
(Estd.By Govt. of Jharkhand & Run by Techno India under PPP), Jharkand.India.
Procurement Under TEQIP III (Quarter 1, April to June 2018)
Wavelength- 850nm and 650nm, Light Source Infra-red
LED, Photo Detector Si PIN Diode
FWHM Spectral Width 100nm, Fiber 1000µm plastic Fiber
(Standard 1m &
3m – Optional 20m) Max Link Length 5m for 850nm link,
Max Data Rate 2Mbits/sec (NRZ)
3. CEC/CONSUMABLES/MACHINE SHOP
Procurement Package Items of Procurement
Aluminium rods for CNC Turning
Machines
Aluminium rods for CNC Turning Machines 22 mm
Diameterx150 mm length Alumunium Rod
Aluminium rods for CNC Turning
Machine
Aluminium rods for CNC Turning Machines
220 mm Diameterx150 mm length Alumunium Rod
Central Lathe of 6’ Bed length with
Thread Cutting arrangement.
High Precision Lathe of Length of Bed 4 Feet,Height of
Centre 165 mm,Width of Bed 238 mm,Hollow Spindle 400
mm with accessaries such as 8"x4 Jaw Precision
Chuck,Centre Adoptation Dead Centre,Square Tool Post.It
is fitted with 1 HP,1440 r.p.m,3 PH Electric Motor.It should
be supplied with Chuck Plate,Face Pale,Follow Rest,Steady
Rest,Rear Tool Post,Splash Guard.
Cutting Tools for CNC Turning Centre Cutting Tools for CNC Turning Centre
4. CEC/CONSUMABLES/STRENGTH OF MATERIALS
Procurement Package Items of Procurement
Test piece for Tensile Test
on Universal Testing
Machine
Dumbbell Shape,Raw Material:-Mild Steel,Total Length=600
mm,Round ends=16.0 mm,Middle portion:- Diameter=12
mm,Length=400 mm.
Test piece for Torsion Test
on Torsion Testing
Machines
Test piece for Torsion Test on Torsion Testing MachineS
Dumbbell Shape,Raw Material:-Mild Steel,Total Length=250
mm,Square ends=12.0 mm Square,Middle portion:- Diameter=8.5
mm,Length=130 mm.
Test piece for Impact Test
on Pendulam Impact
Testing Machine(For Izod
Impact Test)
Test piece for Impact Test on Pendulam Impact Testing
Machine(For Izod Impact Test) Raw Material= Mild Steel,Cross
section=10x10 mm Square,Length=75 mm,V-Shaped Notch 28 mm
away from one end.
Chaibasa Engineering College
(Estd.By Govt. of Jharkhand & Run by Techno India under PPP), Jharkand.India.
Procurement Under TEQIP III (Quarter 1, April to June 2018)
Test piece for Impact Test
on Pendulam Impact
Testing Machine(For
Charpy Impact Test)
Test piece for Impact Test on Pendulam Impact Testing
Machine(For Charpy Impact Test); Raw Material= Mild Steel,Cross
section=10x10 mm Square,Length=55 mm,V-Shaped Notch is at
centre i.e 27.5 mm away from both ends.
5. CEC/ALL DEPT/DESKTOP PC
Procurement Package Items of Procurement
DESKTOP PC Core i7-7th Gen(8MB/3.6Ghz)
Ram – 8 GB DDR4 2400Mhz DIMM
HDD – 1 TB 7.2K RPM
NO ODD
DOS
Monitor – 21.5’’ Monitor
Wired KBB+Mouse
Warranty 3 Years Onsite
6. CEC/OFFICE/ONLINE UPS
Procurement Package Items of Procurement
ONLINE UPS FOR
ADMIN
Online UPS
Rating 10 KVA
Three Phase in Single Phase out
60 minutes backup
Battery with interconnecting cable
Battery Rack
7. CEC/FURNITURE/LIBRARY
Procurement Package Items of Procurement
BOOK RACK Open Library Rack
Size: 78" x 33" x 36"
BOOK SHELF Book Shelf with back side closed and front side
cover.
Each shelf 4 numbers of desks
Height between each desks- 12"
Chaibasa Engineering College
(Estd.By Govt. of Jharkhand & Run by Techno India under PPP), Jharkand.India.
Procurement Under TEQIP III (Quarter 1, April to June 2018)
Shelf height- 54"
Shelf width- 36"
Shelf depth- 15"
8. CEC/SOFTWARE/MATLAB
Procurement Package Items of Procurement
MATLAB SOFTWARE Perpetual Concurrent Network License ;
Academic Version*;
Windows/ Linux/ Mac Platform (25 USER)
9. CEC/ Networking
Procurement Package Items of Procurement
CEC Networking
100Mbp switch(24Ports )
2230Wireless Access point
24 Ports Gigabit Switch
3mt Cat-6 patch cord
6U wall mount rack with 2cable manager ,
Equipment hardware
9U Rack with 4cable manager, 1pdu,hardware
Back box
Cat-6 I/O Module.
Cat-6 patch cord 1mt length
Cat-6 Patch cord 2mt.length
Cat-6 UTP cable (17box)per box 305mt.
Cat-6 UTP cable (17Box) laying with PVC conduit
(17box)per box 305mt.
Chaibasa Engineering College
(Estd.By Govt. of Jharkhand & Run by Techno India under PPP), Jharkand.India.
Procurement Under TEQIP III (Quarter 1, April to June 2018)
Dual Face plate (45Nos.)
I/O fixing and termination
loded patch panel(24Ports)
Rack dressing ,Numbering ,commissioning.
Rack fixing
Rack Tray
RJ-45 Connecter
Single Face plate(65Nos.)
termination of 24Ports patch panel
Wireless Access point
10. CEC/DESKTOP FOR LABORATORIES
Procurement Package Items of Procurement
DESKTOP FOR
LABORATORIES
Desktop Computer
(Desktop Computer: Intel Core Processor i7, DOS,
Processor Speed: 3.6 Ghz , 7th Generation Intel Core
i7 processor Network interface Integrated
10/100/1000M GbE; Ports1 audio line in; 1 audio
line out; 1 HDMI; 1 RJ-45; 1 VGA; USB: 2 USB
3.0; 4 USB 2.0 Storage type: HDD Minimum
dimensions (W x D x H) 17 x 27.4 x 33.8 cm ,
Memory Size (RAM): 8 GB DDR4-2400 SDRAM (1
x 8 GB) Power180 W external AC power adapter
Graphics: Intel HD Graphics 630 SKU2YG38PA
Storage:1 TB 7200 rpm SATA, Display :19.5",Full
HD,Resolution: 1920x1080, LED,Color: Black)
Chaibasa Engineering College
(Estd.By Govt. of Jharkhand & Run by Techno India under PPP), Jharkand.India.
Procurement Under TEQIP III (Quarter 1, April to June 2018)
11. CEC/EE/CIRCUIT THEORY LAB
Procurement Package Items of Procurement
Reciprocity Theorem
Trainer Kit
Reciprocity Theorem with bakelite Panel & Round
Meters
Active Filters with
Operational Amplifier
Desing of a First Order and Second Order
Filters;Fixed output DC regulated Power Supply of
+15V, One Operational Amplifier IC741 is placed
behind the front panel and importent connection are
brought on sockets. Instrument is designed on PCB
model . Different combination of resistance and
capacitors are provided on the front panel ; Optional
Accessories: CRO & Fuction Genarator
Response of a RLC series
Circuit of Step Input
Transient Response of RLC Circuit with Bulit in
Square Wave Oscillator; Optional Accessories: CRO
& Fuction Genarator
LCR impedence Apparatus
with Alluminium and
Square Meter
Instrument comprises of AC power Supply 3-15VAC
able using bandswitch, two AC moving Coil meters
to measure voltage and current , three set of
Resistance, three set of Capacitors and one
inductence connected inside & connections brought
out at Socket/Terminals on front panel.
Three Phase inductive load 120mH,4A,3 Phase,440V,50Hz,Iron Core, Banana
Connection provided for all Input
CRO Dual Channel, DC to 50 MHz, Invert facility in both
Channels / Vertical Deflection coefficients : 5 mV to
20 V/div. / Time Base: 20 ns to 0.2 s/ div; Variable
Hold- Off; X10 Magnification / Triggering: DC-60
MHz; / nate triggering LED indication for stable
triggering / XY mode / Z Modulation / Saw tooth
output (5 Vpp approx ) / Component Tester; 2 Level
Calibrator.
Tellegen's Theorem
Trainer Kit
Tellegen's Theorem with bakelite Panel & Round
Meters
Chaibasa Engineering College
(Estd.By Govt. of Jharkhand & Run by Techno India under PPP), Jharkand.India.
Procurement Under TEQIP III (Quarter 1, April to June 2018)
12. CEC/ALL DEPT/MICROSOFT PRODUCTS
Procurement Package Items of Procurement
PART NO- 3LN-00001 IntuneOpen ShrdSvr ALNG SubsVL OLV E 1Mth Acdmc AP Fclty
Renewal Only
PART NO- 77D-00161 VSProSubMSDN ALNG LicSAPk OLV E 1Y Acdmc AP
Visual Studio Pro Sub MSDN
PART NO- 9EA-00314 WinSvrDCCore ALNG LicSAPk OLV 2Lic E 1Y Acdmc AP CoreLic
Windows Server DC Core
PART NO- KW5-00359 WINEDUE3 ALNG UpgrdSAPk OLV E 1Y Acdmc Ent
WIN EDU E3
PART NO- S2Y-00002 O365ProPlusOpenStudents ShrdSvr ALNG SubsVL OLV NL 1Mth
Acdmc Stdnt STUUseBnft
O365 ProPlus Open for Students
PART NO- S3Y-00001 O365ProPlusOpenFaculty ShrdSvr ALNG SubsVL OLV E 1Mth
Acdmc AP
O365 ProPlus Open for Faculty
13. CEC/DIESEL GENERATOR
Procurement Package Items of Procurement
DIESEL GENERATOR
125 KVA, 3 Phase, 415 V Silent DG Set, Liquid Cooled Engine complete
with Battery, Lube Oil And Std Control Panel Engine (4K1080TAG2)
(KOEL GREEN by Kirloskar)
14. CEC/ECE/ANALOG AND DIGITAL ELECTRONICS LAB
Procurement Package Items of Procurement
A/D and D/A converter 8-bit and 8-bit ladder type DAC are constructed using discrete components /
8-bit monolithic DAC having settling time in the range of ns, wide power
supply range, low power consumption, full scale error ± 1LSB / 8-bit digital
ramp ADC constructed using discrete components / 8-bit monolithic ADC
having conversion time in the range of µs, industry standard pin out, wide
input range 8 on-board switches to provide digital inputs to DAC / 8-bit
Chaibasa Engineering College
(Estd.By Govt. of Jharkhand & Run by Techno India under PPP), Jharkand.India.
Procurement Under TEQIP III (Quarter 1, April to June 2018)
counter running on external clock frequency to study settling time of DAC /
1 KHz sine wave with adjustable amplitude level / On-board variable DC
voltage source for studying unipolar and bipolar modes of ADC / 12 output
LEDs to observe ADC outputs / operates on DC power supply (+12V,-
12V,+5V and GND) / Interconnection is provided by standard 2mm
connector / Extensive experimental manual is provided with the kit
Class A Power Amplifier
Trainer Kit
On panel circuit diagram with output transformer / Power supply + 12 V @
500 mA / Required numbers of patch cords.
Class B push-pull Power
Amplifier Trainer Kit
On panel circuit diagram with output transformer / Power supply + 12 V @
500 mA / Required numbers of patch cords.
CRO Dual Channel, DC to 30 MHz, Invert facility in both Channels / Vertical
Deflection coefficients : 5 mV to 20 V/div. / Time Base: 20 ns to 0.2 s/ div;
Variable Hold- Off; X10 Magnification / Triggering: DC-60 MHz; / nate
triggering LED indication for stable triggering / XY mode / Z Modulation /
Saw tooth output (5 Vpp approx ) / Component Tester; 2 Level Calibrator.
Function Generator Frequency Range 0.3Hz to 3MHz /Waveforms: Sine, Square, Triangle, DC
/DC-Offset Adjustment /Trigger Output /Internal Sweep & External FM-
Modulation .
OP-amp Trainer Kit Function Generators : Sine Wave : 10Hz - 100 KHz (10VPP), Square Wave
: 10Hz - 100 KHz (10 VPP), Triangle Wave : 10Hz - 100 KHz (8 VPP), On
board test Power: 0±15V (variable), Power Supply: 230 V, 50 Hz.
15. CEC/ECE/BASIC AND SOLID STATE DEVICE LAB
Procurement Package Items of Procurement
2 channel DC Power Supply 0 - 30V / 3A Dual Power Supply with Automatic Overload Protection
CRO Dual Channel, DC to 50 MHz, Invert facility in both Channels / Vertical
Deflection coefficients : 5 mV to 20 V/div. / Time Base: 20 ns to 0.2 s/ div;
Variable Hold- Off; X10 Magnification / Triggering: DC-60 MHz; / nate
triggering LED indication for stable triggering / XY mode / Z Modulation /
Saw tooth output (5 Vpp approx ) / Component Tester; 2 Level Calibrator.
Diode Trainer Kit IN4007 Diode Input Output Characteristic and Ripple factor calculation
Transistor Trainer Kit Transistor Tests Supported are : Short Circuit test for NPN /PNP
Transistor/Open Circuit test for NPN / PNP Transistor/ICBO / I CEO test
for NPN / PNP Transistor/HFE (DC) test for NPN / PNP
Transistor/Common Emitter characteristics curve plotting/Determination of
Chaibasa Engineering College
(Estd.By Govt. of Jharkhand & Run by Techno India under PPP), Jharkand.India.
Procurement Under TEQIP III (Quarter 1, April to June 2018)
Transistor Parameters from CE characteristics/Transistor Curve Tracer :
Shows IC vs VCE family of curve on Oscilloscope Support both NPN and
PNP Transistor/Control knobs for Amplitude, number of base steps and
sweep frequency ion for curve tracing
16. CEC/ECE/COMMUNICATION LAB
Procurement Package Items of Procurement
AM Receiver Kit Superheterodyne Receiver Frequency Range : 400 KHz to 1.6 MHz/Intermediate
Frequency : 455 KHz. ONE RF amplifier with variable gain. ONE Frequency
Converter (Mixer).Dual gate MOSFET/Inputs : Local Oscillator and RF
Signal/Output Frequency : 455 KHz adjustable/FI Filter : Dual Tune LC/Voltage
Controlled Oscillator (VCO)/Output Signal: Sine wave for local Oscillator
input/Frequency: From 400 KHz to 1500KHz./Amplitude: Adjustable from 0 to
2Vpp/Output impedence: 50 ohm./ive Amplifier: 2 Stages/Central Frequency: 455
KHz/Load impedence : Variable R-L-C/Gain: 50dB/With Automatic Gain
Control/Diode Envelope Detector/Detection of the positive and negative Envelope
with Variable RC Filter DSB/Product Detector/Operating Frequency : Adjustable
from 400 KHz to 500 KHz SSB/Input amplitude : 1 V pp./Audio Output : Amplifier
with speaker/Receiving Media : Telescopic antenna/cable/Interconnection: 2mm
banana socket/Power Supply: +/-12V.
AM Transmitter Kit Audio Oscillator Frequency : 100 Hz to 10 KHz./Sine wave generator: Amplitude 0
to 2 volt./Audio Input : Audio Preamplifier with Microphone./Voltage Controlled
Oscillator (VCO) Output Signal : Sine wave. Frequency Range : 1) 400 KHz to 500
KHz. 2) 400 KHz to 1500 KHz./Amplitude : Adjustable from 0 to 2 Vpp./Output
Impedanc : 50 ohm./AM/DSB/SSB Modulator Modulation : Amplitude Modulation:
Double Side Band.Single Side Band (USB & LSB).Carrier Input : 1 –1000
KHz./Modulating Input : 0.1 – 100 KHz./Carrier Null : Adjustable. /Output
Amplitude : Adjustable.Ceramic Filter/Center Frequency : 455 KHz./Bandwidth : 10
+/-3 KHz/ Output Amplifier : Gain adjustable. Connected to Cable or
Antenna./Antenna : Telescopic./Interconnection : 2mm Banana Socket./Power
Supply : +12V. ACL
Amplitude
Modulation
Demodulation
Trainer Kit
Message Signal: Sine wave Frequency, 100 Hz to 2.8 KHz, Amplitude 0 to 3V/
Carrier Signal : Sine wave Frequency, 28 KHz to 108 KHz, Amplitude 2V /
Modulation : Balanced Modulator / Amplifier : Op Amp Based / Demodulation :
Diode Detector & LPF / Low Pass Filter : 6th Order LPF/ Supply Voltage (Board) :
+12V, +5V / DC / Supply current : 100 mA (Minimum) / Input Voltage : 230 V/ 50
Hz AC / Interface connectors : 2mm socket
Delta Modulation Message Signal 1 : Frequency 500 Hz, Amplitude 0 to 2.5V / Message Signal 2 :
Chaibasa Engineering College
(Estd.By Govt. of Jharkhand & Run by Techno India under PPP), Jharkand.India.
Procurement Under TEQIP III (Quarter 1, April to June 2018)
Trainer Kit Frequency 1 KHz , Amplitude 0 to 2.5V / Mic Pre Amplifier : Transistor Based /
Sampling Clock : Frequency 256K, 128K, 64K, 32K, 16K, Amplitude 5V / Type of
Modulator : Delta Modulation / Type of Demodulator : Delta Demodulation / Filter :
6th order LPF / Amplifier : Op Amp Based / Supply Voltage (Board) : +12V, +5V /
DC / Supply current : 100 mA (Minimum) / Input Voltage : 230 V/ 50 Hz AC /
Interface connectors : 2mm socket
DSO Bandwidth 50MHz, Real-time Sampling Rate 500 MSa/s, Equivalent Sampling Rate
50GSa/s, Memory Depth: 32Kpts, Trigger types: Edge, Pulse width, Video, Slope,
native, Unique Digital Filter function and Waveform Recorder function, 32
parameters Auto Measure function, Save/recall types: Setups, Waveforms, CSV file,
Picture, Waveform Intensity and grid brightness can be adjusted / Standard
configuration port: USB Host: Support USB flash driver save/recall function
FM Modulation
Demodulation
Message Signal : Sine wave Frequency 100 Hz to 2.8 KHz, Amplitude 0 to 3V/
Carrier Signal : Sine wave Frequency 100 KHz, Amplitude 5V / Modulation : XR
2206 Based / Demodulation : PLL Detector & LPF / Low Pass Filter : 4th Order LPF
/ Supply Voltage (Board) : +12V, +5V / DC / Supply current : 100 mA (Minimum) /
Input Voltage : 230 V/ 50 Hz AC / Interface connectors : 2mm socket
Line Coding Trainer
Kit
Message Signal 1: 8 Bit variable Data, Amplitude 5V/ Message Signal 2: PRBS Data
(15 Bit), Amplitude 5V/ Message Signal 3 : Fixed Data 64K,32K, 1
6K & Amplitude 5V/ Encoding Type : NRZ Level, NRZ Mark, RZ,Manchester,
Manchester Mark/ Decoding : Data O/P 1(NRZ Mark & Manchester Mark) Data O/P
2(RZ & Manchester)/ Comparator : LM 311 Based / Supply Voltage (Board) : +9V /
DC/ Supply current :
100 mA (Minimum)/ Interface connectors : 2mm socket
PAM/PWM/PPM
Modulation
Demodulation
Trainer Kit
Message Signal 1 : Frequency 500 Hz, Amplitude 0 to 5V / Message Signal 2 :
Frequency 1 KHz, Amplitude 0 to 5V / Message Signal 3 : Frequency 2 KHz,
Amplitude 0 to 5V / Carrier Signal (Square) : Frequency 8KHz, 16KHz, 32KHz,
64KHz, Amplitude 5V / Carrier Signal (Triangle) : Frequency 8KHz, 16KHz,
32KHz, 64KHz, Amplitude 2V / Modulator Type (PAM) : 74 HC 4053 Based
(Switching) / Modulator Type (PPM) : IC 555 Based (Timer) / Modulator Type
(PWM) : LM 311 Based (Comparator) / Demodulator : 4th Order LPF / Amplifier :
Op-Amp Based / Supply Voltage (Board) : +12V, +5V / DC / Supply current : 100
mA (Minimum) / Input Voltage : 230 V/ 50 Hz AC / Interface connectors : 2mm
socket
Satellite
Communication
Trainer KIt
Uplink Transmitter: Transmitter with able frequency conversion, 2450-2468 MHz
up-linking able frequencies, Wide band RF amplifier, 16 MHz Bandwidth,
Frequency switch and LED indication, FM Modulation of Audio and Video,
Chaibasa Engineering College
(Estd.By Govt. of Jharkhand & Run by Techno India under PPP), Jharkand.India.
Procurement Under TEQIP III (Quarter 1, April to June 2018)
Coverage area 35m Indoor and 100m outdoor, Transmit Audio, Video, Digital data,
PC data, Tone, Voice, function generator waveforms, Separate section for telemetry
operation. / Inbuilt Tone generator: Frequency: 100Hz to 1 KHz, Amplitude: 0V to
1Vpp, Separate terminals provided for different inputs, Power Supply: 230 V, 50 Hz
/ Satellite Link: Transponder with able Uplink and downlinks frequency conversion,
Light and Temperature sensors for telemetry operations, Delay knob provided for
simulated Transition delay experiment, Detachable Dish Antennas, Power Supply:
230 V, 50 Hz / Downlink Receiver: Receiver with able frequency conversion,
Receives and demodulate three signals simultaneously, Built-in speaker for audio
and video output, Detachable Dish Antenna, Power Supply: 230 V, 50 Hz.
17. CEC/EE/POWER ELECTRONICS & DRIVES LAB
Procurement Package Items of Procurement
AC Drive Product or component type Variable speed drive Product destination Asynchronous
motors Product specific application Simple machine Assembly style With heat sink
Component name ATV312 Motor power kW 0.18 kW Motor power hp 0.25 hp [Us]
rated supply voltage 200...240 V (- 15...10 %) Supply frequency 50...60 Hz (- 5...5
%) Phase 3 phases Line current 2.1 Afor 200 V, 5 kA 1.9 Afor 240 V EMC filter
Without EMC filter Apparent power 0.7 kVA Maximum transient current 2.3 Afor
60 s Power dissipation in W 23 W at nominal load Speed range 1...50 Asynchronous
motor control profile Sensorless flux vector control with PWM type motor control
signal Factory set : constant torque Electrical connection Al1, Al2, Al3, AOV, AOC,
R1A, R1B, R1C, R2A, R2B, LI1...LI6 terminal 0 in² (2.5 mm²) AWG 14 L1, L2, L3,
U, V, W, PA, PB, PA/+, PC/- terminal 0 in² (2.5 mm²) AWG 14 Supply Internal
supply for logic inputsat 19...30 V, <= 100 mAfor overload and short-circuit
protection Internal supply for reference potentiometer (2.2 to 10 kOhm)at 10...10.8
V, <= 10 mAfor overload and short-circuit protection Communication port protocol
Modbus CANopen IP degree of protection IP20 on upper part without cover plate
DC Drive 1 Armature Controller- 2HP,200V/10A;1 Field Controller- 1HP,200V/1A
Digital Storage
Oscilloscope
2 channel Bandwidth 50MHz, Real-time Sampling Rate 500 MSa/s, Equivalent
Sampling Rate 50GSa/s, Memory Depth: 32Kpts, Trigger types: Edge, Pulse width,
Video, Slope, native, Unique Digital Filter function and Waveform Recorder
function, 32 parameters Auto Measure function, Save/recall types: Setups,
Waveforms, CSV file, Picture, Waveform Intensity and grid brightness can be
adjusted / Standard configuration port: USB Host: Support USB flash driver
save/recall function.
Function Genarator Frequency Range 0.3Hz to 3MHz /Waveforms: Sine, Square, Triangle, DC /DC-
Chaibasa Engineering College
(Estd.By Govt. of Jharkhand & Run by Techno India under PPP), Jharkand.India.
Procurement Under TEQIP III (Quarter 1, April to June 2018)
Offset Adjustment /Trigger Output /Internal Sweep.
Mixed Domain
Oscilloscope
MDO3000 Series;1. Oscilloscope
2 and 4 analog channel models
1 GHz, 500 MHz, 350 MHz, 200 MHz, 100 MHz bandwidth models
Bandwidth is upgradable (up to 1 GHz)
Up to 5 GS/s sample rate ,10 M record length on all channels
>280,000 wfm/s maximum waveform capture rate ,Standard passive voltage probes
with 3.9 pF capacitive loading
and 1 GHz, 500 MHz, or 250 MHz analog bandwidth
2. Spectrum Analyzer
Frequency range
Standard: 9 kHz - oscilloscope bandwidth
Optional: 9 kHz - 3 GHz
Ultra-wide capture bandwidth up to 3 GHz
3. Arbitrary Function Generator (Optional)
13 predefined waveform types
50 MHz waveform generation
128 k arbitrary generator record length
250 MS/s arbitrary generator sample rate
4. Logic Analyzer (Optional)
16 digital channels
10 M record length on all channels
121.2 ps timing resolution
5. Protocol Analyzer (Optional)
Serial bus support for I2C, SPI, RS-232/422/485/UART, USB 2.0,
CAN, CAN FD, LIN, FlexRay, MIL-STD-1553, ARINC-429, and
Chaibasa Engineering College
(Estd.By Govt. of Jharkhand & Run by Techno India under PPP), Jharkand.India.
Procurement Under TEQIP III (Quarter 1, April to June 2018)
Audio standards;Digital Voltmeter / Frequency Counter (Free with product
registration)
4-digit AC RMS, DC, and AC+DC RMS voltage measurements
5-digit frequency measurements
Multimeter AC-DC, 600V/10A, Temparature and Frequency,Frequency
Hz(10 Hz – 100 kHz);Maximum voltage between any terminal and earth ground
1000 V
Display (LCD) 4000 counts, s 3/sec ,Battery type 2 AA, NEDA 15A, IEC LR6
Battery life 500 hours minimum (50 hours in LED Test mode without load. The
hours with load depends on the type of LED under test.),Temperature Operating 0 °C
to 40 °C ,Storage -30 °C to 60 °C
Regulated DC
Power Supply
Input Volage-260V +/-10% AC 50Hz; Output current-0-60A;Output Voltage-0-
30V;Ripple:less than 1MV;Two digital meters to monitor the output voltage and
current;Protection:Against short circuit and over load
Signal Probe CAT II Probes with 10x Attenuation, 50 MHz,10MΩ, 12PF,300VRms
TachoMeter Digital Tachometer,Laser Light Detection;Display 5 digits, 10 mm ( 0.4" ) LCD ,
with function annunciation.Measurement & Range 10 to 99,999 RPM.Resolution 0.1
RPM ( <1,000 RPM). 1 RPM (1,000 RPM).
Accuracy ± (0.05% + 1 digit). Detecting distance 50 - 2,000 mm typically. Spec. of
detecting distance are that under the size of reflecting tape is 10 mm square & the
measuring RPM value is 1,800 PPM. The max. detecting distance may change under
different environment, different reflecting tape or the measuring RPM beyond 1800
PRM.Laser light source Less than 1 mW. Class 2 laser red diode. Wave length is
645 nm approximately.
Time base Quartz crystal, 4.194 MHz.Circuit Exclusive one-chip of microcomputer
LSI circuit.Operating Temp. 0 - 50 ( 32 - 122 ).Operating Humidity Less than 80%
R.H.Memory Last / Max. / Min. ... value.Battery 4 x 1.5V AA ( UM-3 )
battery.Power Consumption Approx. DC 20 mA.
Voltage Probe CAT II Probes with 10x Attenuation, 100M Hz,10MΩ, 12PF,300V
Chaibasa Engineering College
(Estd.By Govt. of Jharkhand & Run by Techno India under PPP), Jharkand.India.
Procurement Under TEQIP III (Quarter 1, April to June 2018)
18. CEC/SOFTWARE/SYNOPSYS TCAD TOOL
Procurement Package Items of Procurement
SYNOPSYS TCAD
TOOL
3297-0 IC Workbench Edit/View Plus
4347-0 TCAD Sentaurus Workbench
4348-0 TCAD Sentaurus Workbench Advanced
4350-0 TCAD Sentaurus Process
4351-0 TCAD Sentaurus Process 3D
4352-0 TCAD Sentaurus Device
4353-0 TCAD Sentaurus Device Advanced
4354-0 TCAD Sentaurus Device DSM
4355-0 TCAD Sentaurus Device Compound
4356-0 TCAD Sentaurus Device Opto
4357-0 TCAD Sentaurus Device 3D
4358-0 TCAD Sentaurus Parallel
4359-0 TCAD Sentaurus Device EMW
4360-0 TCAD Sentaurus Device Monte Carlo
4361-0 TCAD Sentaurus Device Power
4362-0 TCAD Sentaurus PCM Studio
4363-0 TCAD Sentaurus PCM Library
4375-0 TCAD Sentaurus Structure Editor
4376-0 TCAD Sentaurus Structure Editor 3D
4476-0 TCAD Sentaurus Process Kinetic MC
5442-0 TCAD-Taurus-Medici
5443-0 TCAD-Taurus-TSuprem4
7099-0 TCAD-Raphael
7620-0 TCAD Sentaurus Device EMW MPI
9935-0 TCAD Sentaurus Visual
19. CEC/ECE/MICROWAVE AND ANTENNA LAB
Procurement Package Items of Procurement
Antenna Trainer Kit Rectangular Patch Antenna/Yagi Antenna/Dipole Antenna/Slot Patch Antenna/Helical
Antenna/Mono Pole Antenna/Slot Antenna/EM Coupled Single Patch/2x1 EM Coupled
Array Antenna/2x2 EM Coupled /Array Antenna/Notch Antenna/Sleeve Antenna/BiQuad
Antenna/Folded Dipole Antenna/Wired Dipole Antenna
Microwave Test Bench Voltage range : 0 - 12 Volts variable/Current : 1 Amp. max/Regulation : 0.2% for +/-
10% variation in the mains supply voltage/Ripple : 1mV rms/Modulation Frequency :
1KHz +/- /10% (900-1100Hz)/Output Connector : BNC(F) for Gunn Oscillator &
TNC(F) for Pin Modulator/Modulation : Square Wave /Frequency: 500Hz to
2000Hz//VSWR meter: Sensitivity: 0.2 micro Volts at a 200 ohm input impedance for full
scale deflection, Noise level : At least 5 dB below full scale at rated sensitivity and
maximum bandwidth with input terminated in 100 ohms and 500 ohms for low and high
respectively. Calibration: Square law, meter indicates SWR, dB. Range: 70 dB input
attenuator provides 60 dB in 10 dB steps, accuracy +/- 0.2 dB per 10 dB steps maximum
cumulative error +/- 0.5 dB. Scale or: "Normal", "Expand", and "-5dB" Meter scale:
SWR1-4, SWR3-10, expand SWR1-1.3, dB 0-10, expand 0-2. Gain Control: Adjusts the
Chaibasa Engineering College
(Estd.By Govt. of Jharkhand & Run by Techno India under PPP), Jharkand.India.
Procurement Under TEQIP III (Quarter 1, April to June 2018)
reference level, variable range 0-10 dB approx. Input: "Crystal" 200 ohms for low
impedance crystal rectifier and 200 K ohm high impedance crystal rectifier as null
detector. A/C output : BNC Connector for amplified output. Input Connector: BNC (F).
Frequency: 1000Hz +/- 10% . Power: 230 Volts AC, 50Hz, mains supply. / Power Meter:
Frequency Range: 100 KHz to 3.0 GHz, Power Range: -30 to +20 dBm, useable to – 40
dBm, Ranging: Auto-ranging , 2 ranges. Linearity: + 0.5 dB @ 250 C + 0.1 dB, 100 to
400 C Sensor Zero: Auto Zero(9000B)/Including: Detector diode, Frequency Meter,
Attenuators, Slotted Section, tunable Probe, Detector mount, E Plane tee, H – Plane tee,
Magic Tee, Cross Directional Coupler, Multi-hole Directional Couplers, Bends, Twists,
Dielectric Cells, Pyramidal Horn Antenna, parabolic Disc Antenna, Wired dipole
Antenna.
RF Signal Generator DC to 2 GHz, 4 GHz or 6 GHz /1 µHz resolution/AM, FM, ØM, PM and sweeps/OCXO
time base (std.) -116 dBc/Hz phase noise (20 kHz offset, f = 1 GHz)/Rubidium time
base/Square wave clock outputs /Analog I/Q inputs /Ethernet, GPIB and RS-232
Spectrum Analyzer Frequency Range from 9 kHz up to 7.5 GHz / Min. -161 dBm Displayed Average Noise
Level (Typ.) /Min. < -98 dBc/Hz @ 10 kHz Offset Phase Noise /Level Measurement
Uncertainty < 0.8 dB /10 Hz Minimum Resolution Bandwidth /Up to 7.5 GHz
19. CEC/SCANNER
Procurement
Package
Items of Procurement
Scanner Scanner type- Sheetfed
Scan resolution, optical Up to 600 dpi (colour and monochrome, sheet-feed)
Duty cycle (daily)- Recommended for 3,500 pages per day
Bit depth- 24-bits external/48-bits internal
Levels of grayscale- 256
Task speed- 10 x 15 cm colour photo to file (200 dpi, 24-bit, tiff): about 6.27 sec for single image scan
OCR A4 (200dpi, 24-bit to RTF): about 7.45 sec for single image scan
10 x 15 cm colour photo to email (150 dpi, 24-bit): about 5.95 sec for single image scan, about 1.08 sec
for single image send to email, totally 7.03 sec
A4 PDF to email (300 dpi, 24-bit): about 7.36 sec for single image scan, about 1.7 sec for single image
send to email, totally 9.06 sec
Media types- Cut sheet paper, printed paper (laser and ink), pre-punched paper, bank checks, business
cards, freight bills, carbonless forms, previously stapled media with staple removed
Media weights, supported ADF- 40 to 413 g/m²
Scan file format- For text and images: PDF, JPEG, PNG, BMP, TIFF, TXT (Text), RTF (Rich Text)
and searchable PDF
Scan input modes- One default scan mode on front-panel for HP scan in Win OS, HP Easy Scan/ICA
in Mac OS and third parties applications via TWAIN, ISIS and WIA
Scanner advanced features- Auto colour detect; Auto crop; Auto exposure; Auto orientation; OCR;
Edge removal; Background cleanup; Remove hole; Colour out; Straighten the page; Scan to cloud;
Scan to email; PDF security; Misfeed detection advance setting
Control panel- Scan button, Cancel button, Power button with a LED and a LED for Error indication
Automatic document feeder capacity- 50 sheets
Automatic document feeder speed Up to 35 ppm/70 ipm 3
Chaibasa Engineering College
(Estd.By Govt. of Jharkhand & Run by Techno India under PPP), Jharkand.India.
Procurement Under TEQIP III (Quarter 1, April to June 2018)
Scan size (ADF), maximum 216 x 3100 mm
Scan size (ADF), minimum 50.8 x 74 mm
Compatible operating systems- OS X El Capitan 10.11 Microsoft® Windows® 10, 8.1, 8, 7: 32-bit/64-
bit
Mac compatible
Connectivity, standard- Hi-Speed USB 2.0 and USB 3.0
Connectivity, optional- USB 2.0 port for Wi-Fi accessory
Twain version 2.1
Dimensions (W x D x H)-310 x 198 x 190 mm
Weight-3.4 kg