CERTIFICATE OF COMPLIANCE AND CALIBRATION

This Certificate certifies that the material furnished as listed below has been tested, manufactured, cali­brated and/or inspected in accordance with IDEAL INDUSTRIES procedures. These procedures are IS0-9001 controlled and are designed to assure that the instrument will meet its published specification.

Inspections and/or tests and Calibration have been performed, as applicable, on both a variable and attribute basis at:

IDEAL INDUSTRIES, Inc 9650 Chesapeake Drive

San Diego, CA 92123

Calibration compliance is achieved by comparison to a calibrated standard, an Automated Test Equipment (ATE) Station, in accordance with IDEAL LanTEK System Factory Calibration Pro-

. cedure 0028-00-0434 on file at the above address. These procedures document the periodicity, methods, and maintenance of calibration certificates showing traceability of calibration of the ATE with a Network Analyzer with calibration certificates documenting traceability to the Nation­al Institute of Standards and Technology (NIST).

Objective evidence in the form of tesUor inspection reports for the equipment listed below is maintained at the above address.

NEW Customer name:

Display Handset Model: 33-993

Remote Handset Model: 33-993

Date received:

Condition received:

Date of Calibration: June-01-12

Serial No.

Serial NO

Environmental Conditions: 2

_012

Temperature: ~ °C

Firmware Version:

1222063

1222071

Relative Humidity:~%

Uncertainty of measurement statement: The measurement accuracy of LANTEK II is verified semiannually via random testing by lntertek Testing Services (ITS), a division of ETL Semko, to be compliant with the Level IV Accuracy Specification as specified by the IEC 61935-1, Draft Standard, Table 12 "Level IV field Tester accuracy performance parameters per IEC guide­lines." This table is shown on the reverse side of this certificate. ITS Verification Reports are on file at the above listed address.

Service Technician Performing Calibration: D . Nguyen

Recommended Date for Next Calibration: June-01 -13

0 2012 Groat Papen

Table 12: Level IV field tester accuracy performance parameters per IEC guidelines. (from IEC 61935:2004)

Parameter

Dynamic Range

Amplitude Resolution

Frequency Range

Amplitude Resolution

Dynamic Accuracy

NEXT

ELF EXT

Tester Source/Load Return Loss

Random Noise Floor

Residual

NEXT Residual

FEXT Output Signal

Balance Common mode

Rejection Tracking

Directivity

Source Match

Return Loss of

Termination

Note 1 Note 2

Note 3

Note4

Note 5

Note&

Variable Baseline Field Tester with CLASS F Field Tester with CLASS F Name Field Tester Permanent Link Adapter Channel Adapter

" 3 dB over test limit

PP NEXT & FEXT loss 65 dB PS NEXT & FEXT loss 62 dB

0.1

1 -600 MHz

1 - 31.25 MHz, 150 KHz 31.25 to 100 MHz, 250KHz

1 00 to 250 MHz, 500 KHz 250 to 600 MHz, 1 MHz

Ed NEXT ± 0.75- Note 1

Ed FEXT ± 1.0-Note2

1-250 MHz 1-250 MHz 1-250 MHz E_RL_Test 20- 12.51og (f/100) 18 - 12.5 log (f/1 00) 16- 12.51og (f/100)

20 dB Max 20 dB Max 20 dB Max 250-600 MHz: 15 dB max 250-600 MHz: 13 dB max 250-600 MHz: 13 dB max

E_NF 95-15 log (f/100) 95-15 log (f/100) 95-151og (f/100) 100 dB max 95 dB max 95 dB max

E_RN 90-20 log (f /1 00) 85-20 log (f/1 00) 80-20 log (f /1 00)

Note3 Note3 Note3 E_RF 90-20 log (f/1 00) 85-20 log (f/1 00) 60-20 log (f /1 00)

Note4 Note4 Note4

E_OSB 43-20 log (f/100) 40-20 log (f/1 00) 40-20 log (f/100) Note 5 Note5 Note5

E_CMR 40-20 log (f/100) 40-20 log (f /1 00) 40-20 log (f /1 00)

Not~5 Note 5 Note 5 TR ±0.5- Note 5 Dir 1-250 MHz 1-250 MHz 1-250 MHz

27 - ?log (f/1 00), 30 dB 25 - 7 log (f/1 00), 30 dB max 25- 7 log (f/100), 30 dB max

250 - 600 MHz: 24.2 dB 250 - 600 MHz: 22.2 dB Floor 250 - 600 MHz: 22.2 dB Floor

Note6 Note 6 Note6

SM 20 - 20 log (f/1 OO) 20 - 20 log (f/1 OO) 20 - 20 log (f/1 OO) 20 dB Max 20 dB Max 20 dB Max

E_TERM_RL 1-250 MHz 1-250 MHz 1-250 MHz 20 - 15 log (f/1 00) 18-15 log (f/100) 20 - 15 log (f/1 00)

25 dB max 25 dB max 25 dB max -250-600 MHz: 14 dB Floor 250 - 600 MHz: 12 dB Floor 250 - 600 MHz: 12 dB Floor

Note6 Note6 Note6 Venficat1on of dynamiC accuracy IS requ1red up to the specified range for NEXT loss and FEXT Loss. The dynamic accuracy is based on dynamic accuracy performance for insertion loss (attenuation) and NEXT loss, and is assumed to combine the dynamic accuracy for ELF EXT as specified. The FEXT loss dynamic accuracy is tested to± 0.75 dB. The highest FEXT value to be measured is 70 dB.

I

I

Performance verification of residual NEXT is up to 90 dB maximum. It is assumed that the frequency response changes at a rate that is specified for Category 7 connecting hardware. The impact of reflected FEXT of the adapter to residual NEXT are to be accommodated within this residual NEXT requirement. Performance verification of residual NEXT is up to 90 dB maximum. It is assumed that the frequency response changes at a rate that is specified for Category 7 connecting hardware. Performance verification of Output Signal Balance and Common Mode Rejection is up to 60 dB maximum. It is assumed that the frequency response changes at a rate of 20 dB/decade. The performance requirements for tracking, directivity, source match and return loss of termination are appli­cable when the insertion loss exceeds 3 dB. It is assumed that the performance of the permanent link and channel adapters is verified after calibration with the baseline instrument.

Units

dB

dB

MHz 1

MHz

dB

dB

dB

I

dB I

dB

dB

dB

dB

dB

dB

dB

dB