CERTI FICATE - portal.segensolar.co.za
2
ZERT CERTI FICATE Conformity of the Factory Production Control 245r-CpR-E N L090-20 t 4.0 L02,003 ln compliance with Regulation 305/2011/EU of the European Parliament and of the Council of 9 March 201.1. (the Construction Products Regulation or CPR), this certificate applies to the following construction product: product method plant manufãcturer tssue audit validity date of issue Düsseldorf, 07.05.20L9 Hase Dipl.-lng. Gurschke Head of certification body Structural components and kits for aluminium structures to EXC3 according to EN 1090-3 for load-bearing structures in all types of buildings 2A.3.2 to 24.3.5 acc. to EN 1090-L:2009+A1:2011 produced by or for Schletter Solar GmbH Gewerbegebiet an der 815 Alustraße 1 83527 Kirchdorf / Haag i. OB GERMANY Schletter Solar GmbH Gewerbegebiet an der BL5 Alustraße L 83527 Kirchdorf / Haag i. OB GERMANY This certificate attests that all provisions concerning the assessment and verification of constancy of performance described in Annex ZA of the harmonised standard EN 1090-1:2009+A1:2011 under system 2+ are applied, and that the factory production control fulfills all the prescribed requirements stated therein. 24.0L.20L2 23.0L.2022 This certificate will remain valid as long as the test methods and/or the factory production control requirements included in the harmonised standard used to assess the performance of the declared characteristics do not change, and the product and the manufacturing conditions in the plant are not modified significantly see reverse (o*ts*" Aachener Straße I 72, 40223 Düsseldorf, GERMANY D-ZE-1@{10
Transcript of CERTI FICATE - portal.segensolar.co.za
ZERT
CERTI FICATEConformity of the Factory Production Control
245r-CpR-E N L090-20 t 4.0 L02,003ln compliance with Regulation 305/2011/EU of the
European Parliament and of the Council of 9 March 201.1. (the Construction ProductsRegulation or CPR), this certificate applies to the following construction product:
product
method
plantmanufãcturer
tssue
audit
validity
date of issue Düsseldorf, 07.05.20L9Hase
Dipl.-lng. GurschkeHead of certification body
Structural components and kits for aluminium structuresto EXC3 according to EN 1090-3
for load-bearing structures in all types of buildings
2A.3.2 to 24.3.5 acc. to EN 1090-L:2009+A1:2011
produced by or for
Schletter Solar GmbHGewerbegebiet an der 815Alustraße 183527 Kirchdorf / Haag i. OBGERMANY
Schletter Solar GmbHGewerbegebiet an der BL5Alustraße L83527 Kirchdorf / Haag i. OBGERMANY
This certificate attests that all provisions concerning theassessment and verification of constancy of performancedescribed in Annex ZA of the harmonised standard
EN 1090-1:2009+A1:2011under system 2+ are applied, and that the factoryproduction control fulfills all the prescribed requirementsstated therein.
24.0L.20L2
23.0L.2022
This certificate will remain valid as long as the test methodsand/or the factory production control requirements includedin the harmonised standard used to assess the performance of thedeclared characteristics do not change, and the product and themanufacturing conditions in the plant are not modified significantly
see reverse
(o*ts*"Aachener Straße I72, 40223 Düsseldorf, GERMANY
D-ZE-1@{10
Remarks
ZÊRT
Certificate number: 245 l-CPR-EN f 090.2014.0102.003
The Notified Body - 2451 DVS ZERT GmbH has performed the initial inspectionof the/of manufacturing plant(s) and of the factory production control andperforms the continuous surveillance, assessment and approval of the factoryproduction control.
General provisions
The conditions of the standard EN 1090-1:2009+41:2011, from section B. 4,1 until including section B. 4.4,must be fulfilled.
The requirements of EN 1090-1:2009 + AL: 201 1, section B. 4.3 are observed. These refer to the annualstatements to be submitted in writing of the manufacturer to the Notified Body.
The General Terms and Conditions of the DVS ZERT GmbH apply in the currently valid version.
a
DVS ZERTGmbH, Aachener Straße 172, 40223 Düsseldorf, GERMANYßnn¡H*.
Árrrld&ru[ShDZE-16@10
