CeILInG systems - Intexintex.com.au/wp-content/uploads/2011/11/Purlin-Clips-1589.pdf · 9WN06...
-
Upload
truonghanh -
Category
Documents
-
view
231 -
download
4
Transcript of CeILInG systems - Intexintex.com.au/wp-content/uploads/2011/11/Purlin-Clips-1589.pdf · 9WN06...
B U I L D I N G E XC E L L E N C E
15 Intex® Group Buyer’s GuIde | FreeCALL Aust: 1300 107 108 nZ: 0800 278 276 | e [email protected] | w intex.com.au
ceiling systems
BAcK tO CONTENTS <<
2H1 2H2 2VF 2H7A/B 2H10 9S640 9S660 9AC25T 9WN06 9TC632
produCt Code desCrIptIon pACkQty.
rod suspensIon Components
rAnGe oF CLIps And FAsteners to hAnG suspensIon rod From
2H1 Suspension Rod Bracket 1002H2 Suspension Rod Bracket Right Angle 100
2VF Purlin Clip (VF1) 100
2H7A Tie Wire Spike 5mm hole 5 X 32 1002H7B Tie Wire Spike 5mm hole 6.5 x 32 1002H10 Pipe Spike with 6mm Internal Thread 100
9S625 Suspension Anchor Sleeve Type 6.5 x 25mm 1009S640 Suspension Anchor Sleeve Type 6.5 x 40mm 100
9S660 Suspension Anchor Wedge Type 6.0 x 60mm 100
9WN06 Wedge Nut for Bondek Roofing 6mm Internal Thread 100
9AC25T Angle Clip Assembly Powder Actuated 1009TC632 Threaded Clip Assembly - 6mm - Powder Actuated 100
produCt Code desCrIptIon LenGth(mm)
pACk Qty.
suspensIon rod
A pLAIn GALvAnIsed rod/wIre For use In suspended CeILInG systems.
2R536 Suspension Rod 5mm - Galvanised 3600 402R540 Suspension Rod 5mm - Galvanised 4000 40
threAded rod
metrIC 6mm ALL threAd And nuts For use In suspended CeILInG AppLICAtIons. other metrIC And ImperIAL sIZes AvAILABLe on reQuest.
2RTA30* All Thread 6mm Metric (cut to size available) 3000 1002RTA015 All Thread 6mm Metric 150 100
2RN Nuts 6mm Metric 100
other sIZes oF threAded rod & suspensIon Components AvAILABLe on reQuest.*LeAd tIme mAy Be reQuIred
B U I L D I N G E XC E L L E N C E
89 Intex® Group Buyer's GuIde | FreeCALL Aust: 1300 107 108 nZ: 0800 278 276 | e [email protected] | w intex.com.au
BACK TO CONTENTS <<
FASTENERS &ACCESSORIESFASTENERS - CONSTRuCTION
produCt Code desCrIptIonHoLesIZe (MM)
LenGtH(MM)
pACkQty.
MICkey pIns
FIne sHAnk MAsonry nAILs wItH wAsHer, For HAMMerInG Into ConCrete.
9MP20 Fine Shank Masonry Nail with Washer 2.5 x 20 2.5 20 500/5,0009MP25 Fine Shank Masonry Nail with Washer 2.5 x 25 2.5 25 500/5,000
For HAMMer drIve tooLs see pAGe 157
wedGe nuts
desIGned For tHreAded rod suspensIon FroM “Bondek” rooFInG wItH no drILLInG reQuIred.
9WN06 Suspension Nut for “Bondek” Decking 6mm Thread 100
For tHreAded rod see pAGe 15
pLAsterBoArd AnCHorsone pIeCe HoLLow Body seLF drILLInG AnCHors desIGned For use In pLAsterBoArd to provIde A FAstenInG poInt. CorrosIon resIstAnt MetAL ALLoy.
9PAZ1 Self Drilling Anchor Metal Alloy 100/1,000
nyLon AvAILABLe on reQuest
produCt Code desCrIptIon pACkQty.
suspensIon BrACkets
2H1 Rod Clip 100
2H2 Rod Clip Right Angle 100
2VF Purlin Clip (VF1) 100/1,000
For CeILInG systeMs see pAGe 11, 182H1 2H2 2VF
produCt Code desCrIptIonHeAd
dIAMeter (MM)
LenGtH(MM)
pACkQty.
drIve pIns - 8MM HeAdFor use In Intex®: Ap360, Ap099 HILtI: dx350, dx36M, dxA40, dxA41, dx460 HILtI pneutek: dx600n MACsIM: AM75, As95, powers: p3500, pA351 rAMset: s75A, ts750, d200, d90, d60, jp50, jp88, e45, ts60p, ForM MAster, joB MAster, FIx MAster, ty MAster, FrAMe MAster, ts750p reId: exp360, Bet0200, exp460. desIGned For perMAnent FAstenInG In ConCrete And soMe types oF BLoCk. ALL pIns HAve pLAstIC FLute over poInt to HoLd pIn In tooL.
9X825 Drive Pin for Concrete 8mm 25 100/1,0009X851 Drive Pin for Concrete 8mm 51 100/1,0009X863 Drive Pin for Concrete 8mm 63 100/1,0009X876 Drive Pin for Concrete 8mm 76 100/1,000