CE SAR EVALUATION REPORT - THL · 2014. 12. 10. · Performed Location: Shenzhen Sunway...
Transcript of CE SAR EVALUATION REPORT - THL · 2014. 12. 10. · Performed Location: Shenzhen Sunway...
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 1 / 126
CE SAR EVALUATION REPORT
For
Shenzhen Hongjiayuan Communication
Technology Co., Ltd.
Product Name: smart phone
Model No. : thl 4400, thl 4400s, thl 4400e, thl 5000,
thl 5000s,thl 5000e, S 5000, S 4400
Date of Receipt: 11th June. 2014
Date of Test: 13th ~16th June. 2014
Issued Date: 16th June. 2014
Report No.:TS201406010
Report Version:V1.0
Issue By
Shenzhen Sunway Communication CO.,LTD Testing Center
1/F,BuildingA,SDG Info Port, KefengRoad,Hi-Tech Park, Nanshan District,
Shenzhen , Guangdong, China 518104,
Note: The test results relate only to the samples tested. This report shall not be reproduced in
full, without the written approval of SUNWAY Testing Center.
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 2 / 126
SAR Evaluation compliance
Product Name: Smart phone
Brand Name: THL
Model Name: thl 4400, thl 4400s, thl 4400e, thl 5000, thl 5000s,
thl 5000e, S 5000, S 4400
Applicant: Shenzhen Hongjiayuan Communication Technology Co.,Ltd.
Address: 6 Floor,Block 12,Dongfangjianfuyusheng
Industrial,Gushu,Baoan District,Shenzhen City,China
Manufacturer: Shenzhen Hongjiayuan Communication Technology Co.,Ltd.
Address: 6 Floor,Block 12,Dongfangjianfuyusheng
Industrial,Gushu,Baoan District,Shenzhen City,China
Applicable
Standard:
EN 50360:2001, EN 50566:2013;
EN 62209-1:2006, EN 62209-2:2010
Test Result: Max. SAR Measurement
Body (10g): 0.276 mW/g
Head(10g): 0.132 mW/g
Performed Date: 13th ~16th June. 2014
Test Engineer:
Reviewed By
Performed Location: Shenzhen Sunway Communication CO.,LTD Testing Center
1/F,BuildingA,SDG Info Port, KefengRoad,Hi-Tech Park,
Nanshan District,Shenzhen , Guangdong, China 518104
Tel: +86-755- 36615880
Fax: +86-755- 86525532
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 3 / 126
TABLE OF CONTENS
1. General Information: .......................................................................................................... 5
1.1 EUT Description: ............................................................................................................. 5
1.2 Test Environment: ........................................................................................................... 7
2. SAR Measurement System: ............................................................................................... 8
2.1 Dasy4 System Description: ............................................................................................. 8
3. System Components: ......................................................................................................... 9
4. Tissue Simulating Liquid ................................................................................................. 11
4.1 The composition of the tissue simulating liquid: ............................................................ 11
4.2 Tissue Calibration Result: .............................................................................................. 11
4.3 Tissue Dielectric Parameters for Head and Body Phantoms: ........................................ 12
5. SAR System Validation .................................................................................................... 13
5.1 Validation System: ......................................................................................................... 13
5.2 Validation Dipoles: ......................................................................................................... 13
5.3 Validation Result: .......................................................................................................... 14
6. SAR Evaluation Procedures: ........................................................................................... 15
7. SAR Exposure Limits ....................................................................................................... 16
8. Measurement Uncertainty: ............................................................................................... 17
9. Conducted Power Measurement: .................................................................................... 19
10. Test photos and results: ................................................................................................ 23
10.1 DUT photos: ................................................................................................................ 23
10.2 Setup photos: .............................................................................................................. 24
Side1 ................................................................................................................................... 27
Side2 ................................................................................................................................... 28
Side3 ................................................................................................................................... 28
Side4 ................................................................................................................................... 29
Side5 ................................................................................................................................... 29
Side6 ................................................................................................................................... 30
11. Equipment List: ............................................................................................................... 34
Appendix A. System validation plots: ................................................................................. 35
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 4 / 126
Appendix B. SAR Test plots: ............................................................................................... 39
Appendix C. Probe Calibration Data: .................................................................................. 71
Appendix D. DAE Calibration Data: ..................................................................................... 85
Appendix E. Dipole Calibration Data: ................................................................................. 90
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 5 / 126
1. General Information:
1.1 EUT Description:
EUT Information
Product Name Smart phone
Brand Name THL
Model Name thl 4400, thl 4400s, thl 4400e, thl 5000, thl 5000s,
thl 5000e, S 5000, S 4400
Hardware Version PLOIECH 94V-0 E169 497 1417K
Software Version /
Device Category Smart phone
Antenna Type Fixed Internal Antenna
Headset Support
Battery Type:3.8V 4400mAh Li-ion Battery
Dimensions (L*W*H): 140mm (L)× 70mm (W)×10mm (H)
Power Source:
Manufacturer:AQUIL STARPRECISION INDUSTRIAL
(SHENZHEN) CO., LTD
Model:ASUC45e-050150
Input: AC 100-240V 50/60Hz 0.45A
Output: DC 5.0V, 1500mA
Normal Operation: Head and Body-Worn
GPS
Class of SRD Class 3
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 6 / 126
GSM-2G
Support Band GSM900/DCS1800
GPRS Type Class B
GPRS Class Class 33
Frequency Bands: GSM 900: UL: 880-915 MHz DL: 925-960 MHz
DCS 1800: UL: 1710-1785 MHz DL: 1805-1880 MHz
Release Version R99
Type of modulation GMSK for GSM/GPRS/EGPRS
Antenna Gain GSM900: 0.21dBi
GSM1800: -0.14dBi
WCDMA-3G
Support Band WCDMA Band I
Frequency Bands: WCDMA Band I:
UL: 1920 ~ 1980MHz DL: 2110 ~ 2170MHz
Release Version Rel-5
Type of modulation QPSK
Antenna Gain WCDMA2100: 0.22dBi
WIFI
Wi-Fi Frequency 802.11b/g/n(20MHz): 2412~2472MHz
Type of modulation 802.11b: DSSS; 802.11g/n: OFDM
Data Rate
802.11b: 1/2/5.5/11 Mbps
802.11g: 6/9/12/18/24/36/48/54 Mbps
802.11n: up to 150 Mbps
Antenna Gain WIFI: 0.65dBi
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 7 / 126
1.2 Test Environment:
Ambient conditions in the SAR laboratory:
Items Required Actual
Temperature (℃) 18-25 22~23
Humidity (%RH) 30-70 55~65
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 8 / 126
2. SAR Measurement System:
2.1 Dasy4 System Description:
The DASY4 system for performing compliance tests consists of the following items:
A standard high precision 6-axis robot with controller, teach pendant and software. An arm
extension for accommodating the data acquisition electronics (DAE).
A dosimetric probe, i.e., an isotropic E-field probe optimized and calibrated for usage in
tissue simulating liquid. The probe is equipped with an optical surface detector system.
A data acquisition electronics (DAE) which performs the signal amplification, signal
multiplexing, AD-conversion, offset measurements, mechanical surface detection, collision
detection, etc.
The Electro-optical converter (EOC) performs the conversion between optical and
electrical of the signals for the digital communication to the DAE and for the analog signal
from the optical surface detection.
A probe alignment unit which improves the (absolute) accuracy of the probe positioning.
A computer operating Windows 2000 or Windows XP.
DASY4 software.
Remote control with teach pendant and additional circuitry for robot safety such as warning
lamps, etc.
The SAM twin phantom enabling testing left-hand and right-hand usage.
The device holder for handheld mobile phones.
Tissue simulating liquid mixed according to the given recipes.
Validation dipole kits allowing to validate the proper functioning of the system.
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 9 / 126
3. System Components:
DAsY4 Measurement Server:
Calibration: No calibration required.
DATA Acquisition Electronics (DAE):
Calibration: Recommended once a year
Dosimetric Probes:
Calibration: Recommended once a year
The DASY4 measurement server is based on a
PC/104 CPU board with a 166MHz low-power
pentium, 32MB chipdisk and 64MB RAM. The
necessary circuits for communication with either
the DAE4 (or DAE3) electronic box as well as the
16-bit AD-converter system for optical detection
and digital I/O interface are contained on the
DASY4 I/O-board, which is directly connected to
the PC/104 bus of the CPU board.
The data acquisition electronics consists of a
highly sensitive electrometer grade preamplifier
with auto-zeroing, a channel and gain-switching
multiplexer, a fast 16 bit AD converter and a
command decoder and control logic unit.
Transmission to the measurement server is
accomplished through an optical downlink for
data and status information as well as an optical
uplink for commands and the clock.
Model: ES3DV3,
Frequency: 10MHz to 3G, Linearity:±0.2dB,
Dynamic Range: 10 µW/g to100 mW/g
Directivity:
± 0.3 dB in HSL (rotation around probe axis)
± 0.5 dB in tissue material (rotation normal to
probe axis)
These probes are specially designed and
calibrated for use in liquids with high permittivities.
They should not be used in air, since the spherical
isotropy in air is poor (±2 dB). The dosimetric
probes have special calibrations in various liquids
at different frequencies.
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 10 / 126
Light Beam unit:
Calibration: No calibration required.
SAM Twin Phantom:
The bottom plate contains three pair of bolts for locking the device holder. The device holder
positions are adjusted to the standard measurement positions in the three sections. A white
cover is provided to tap the phantom during off-periods to prevent water evaporation and
changes in the liquid parameters. On the phantom top, three reference markers are provided
to identify the phantom position with respect to the robot.
Device Holder for SAM Twin Phantom:
The DASY device holder has been made out of low-loss POM material having the following
dielectric parameters: relative permittivity "=3 and loss tangent _=0.02. The amount of
dielectric material has been reduced in the closest vicinity of the device, since measurements
have suggested that the influence of the clamp on the test results could thus be lowered
The light beam switch allows automatic "tooling"
of the probe. During the process, the actual
position of the probe tip with respect to the robot
arm is measured, as well as the probe length and
the horizontal probe offset. The software then
corrects all movements, such that the robot
coordinates are valid for the probe tip. The
repeatability of this process is better than 0.1
mm.
The SAM twin phantom is a fiberglass shell
phantom with 2mm shell thickness (except the
ear region where shell thickness increases to
6mm). It has three measurement areas:
• Left hand
• Right hand
• Flat phantom
The DASY device holder is designed to cope with
different positions given in the standard. It has two
scales for the device rotation (with respect to the
body axis) and the device inclination (with respect
to the line between the ear reference points). The
rotation centers for both scales is the ear reference
point (ERP). Thus the device needs no
repositioning when changing the angles.
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 11 / 126
4. Tissue Simulating Liquid
4.1 The composition of the tissue simulating liquid:
4.2 Tissue Calibration Result:
INGREDIENT
(% Weight)
900MHz
Head/Body
1800MHz
Head/Body
1900MHz
Head/Body
2450MHz
Head/Body
Water 40.92 52.64 54.90 46.7
Salt 1.48 0.36 0.18 0.00
Sugar 56.5 0.00 0.00 0.00
HEC 0.40 0.00 0.00 0.00
Preventol 0.10 0.00 0.00 0.00
DGBE 0.00 47.0 44.92 53.3
Head /Body Tissue Simulate Measurement:
Dielectric Probe Kit: Speag DAK 3.5mm probe -S/N:1038
Frequency
(MHz) Description
Dielectric Parameters Tissue
Temp.
(℃)
Data εr σ[s/m]
900MHz
Reference 41.50±5%
(39.425~43.574)
0.97±5%
(0.9215~1.0185) N/A
2014.06.13
Measurement 42.14 0.98 22.1
1800MHz
Reference 40±5%
(38~42)
1.40±5%
(1.33~1.47) N/A
2014.06.13
Measurement 39.84 1.39 21.8
1900MHz
Reference 39.9±5%
(37.91~41.89)
1.42±5%
(1.35~1.49) N/A
2014.06.13
Measurement 39.39 1.44 22.5
2450MHz
Reference 39.2±5%
(37.24~41.16)
1.80±5%
(1.71~1.89) N/A
2014.06.14
Measurement 39.60 1.81 22.3
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 12 / 126
4.3 Tissue Dielectric Parameters for Head and Body Phantoms:
According to EN 62209-2:2010, the liquid parameters for head are the same as body
requirements.
Target Frequency
(MHz)
Head/Body
εr σ[s/m]
150 52.3 0.76
300 45.3 0.87
450 43.5 0.87
835 41.5 0.90
900 41.5 0.97
915 41.5 0.98
1450 40.5 1.20
1610 40.3 1.29
1800-2000 40.0 1.40
2450 39.2 1.80
3000 38.5 2.40
5800 35.3 5.27
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 13 / 126
5. SAR System Validation
5.1 Validation System:
5.2 Validation Dipoles:
The dipoles used is based on the IEEE-1528/EN62209-1 standard, and is complied with
mechanical and electrical specifications in line with the requirements of both
IEEE-1528/EN62209-1 and FCC Supplement C. the table below provides details for the
mechanical and electrical specifications for the dipoles
Frequency L(mm) H(mm) D(mm)
900MHz 149.0 83.3 3.6
1750MHz 73.0 42.7 3.6
1900MHz 68.0 39.5 3.6
2450MHz 51.5 30.4 3.6
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 14 / 126
5.3 Validation Result:
System performance check at 900MHz,1750MHz, 2450MHz
Validation Dipole: D900V2-SN:1d086
Frequency
(MHz) Description
SAR(1g)
W/Kg
SAR(10g)
W/Kg
Tissue
Temp.
(℃)
Data
900MHz Reference
10.7±10%
(9.63~11.77)
6.87±10%
(6.18~7.49) N/A
2014.06.13
Validation 10.72 6.92 22.5
Validation Dipole: D1750V2-SN:1021
1750MHz Reference
34.6±10%
(31.2~38.0)
18.3±10%
(16.4~20.1) N/A
2014.06.13
Validation 35.32 18.28 22.5
Validation Dipole: D1900V2-SN:5d175
1900MHz Reference
39.9±10%
(35.91~43.89)
20.8±10%
(18.72~22.88) N/A
2014.06.13
Validation 39.76 20.08 22.5
Validation Dipole: D 2450V2-SN:910
2450MHz Reference
53.4±10%
(48.06~58.74)
24.8±10%
(22.32~27.28) N/A
2014.06.14
Validation 50.8 23.36 22.5
Note: Note: All system validation SAR values are measured at 24dBm and normalized
to 1W forward power.
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 15 / 126
6. SAR Evaluation Procedures:
The procedure for assessing the average SAR value consists of the following steps:
Power Reference Measurement
The Power Reference Measurement and Power Drift Measurement jobs are useful jobs for
monitoring the power drift of the device under test in the batch process. Both jobs measure
the field at a specified reference position, at a selectable distance from the phantom
surface. The reference position can be either the selected section’s grid reference point or
a user point in this section. The reference job projects the selected point onto the phantom
surface, orients the probe perpendicularly to the surface, and approaches the surface using
the selected detection method.
Area Scan
The Area Scan is used as a fast scan in two dimensions to find the area of high field
values, before doing a finer measurement around the hot spot. The sophisticated
interpolation routines implemented in DASY4 software can find the maximum locations
even in relatively coarse grids. The scanning area is defined by an editable grid. This grid
is anchored at the grid reference point of the selected section in the phantom. When the
Area Scan’s property sheet is brought-up, grid settings can be edited by a user.
Zoom Scan
Zoom Scans are used to assess the peak spatial SAR values within a cubic averaging
volume containing 1 g and 10 g of simulated tissue. The default Zoom Scan measures 7 x
7 x 7 points (5mmx5mmx5mm) within a cube whose base faces are centered on the
maxima found in a preceding area scan job within the same procedure.
Power Drift Measurement
The Power Drift Measurement job measures the field at the same location as the most
recent power reference measurement job within the same procedure, and with the same
settings. The Power Drift Measurement gives the field difference in dB from the reading
conducted within the last Power Reference Measurement.
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 16 / 126
7. SAR Exposure Limits
SAR assessments have been made in line with the requirements of 1999/519/EC,
EN 50360 and EN62311.
Note: Occupational/Uncontrolled Environments are defined as locations where there is
exposure that may be incurred by people who are aware of the potential for exposure,(i.e. as
a result of employment or occupation)
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 17 / 126
8. Measurement Uncertainty:
NO Source Uncert.
ai(%)
Prob.
Dist.
Div.
k
ci
(1g)
ci
(10g)
Stand.
Uncert.
ui (1g)
Stand.
Uncert.
ui (10g)
Veff
1 Repeat 0.04 N 1 1 1 0.04 0.04 9
Instrument
2 Probe calibration 7 N 2 1 1 3.5 3.5 ∞
3 Axial isotropy 4.7 R
0.7 0.7 1.9 1.9 ∞
4 Hemispherical
isotropy 9.6 R
0.7 0.7 3.9 3.9 ∞
5 Boundary effect 1.0 R
1 1 0.6 0.6 ∞
6 Linearity 4.7 R
1 1 2.7 2.7 ∞
7 Detection limits 1.0 R
1 1 0.6 0.6 ∞
8 Readout electronics 0.3 N 1 1 1 0.3 0.3 ∞
9 Response time 0.8 R
1 1 0.5 0.5 ∞
10 Integration time 2.6 R
1 1 1.5 1.5 ∞
11 Ambient noise 3.0 R
1 1 1.7 1.7 ∞
12 Ambient reflections 3.0 R
1 1 1.7 1.7 ∞
13 Probe positioner
mech. restrictions 0.4 R
1 1 0.2 0.2 ∞
14
Probe positioning
with respect to
phantom shell
2.9 R
1 1 1.7 1.7 ∞
15 Max.SAR evaluation 1.0 R
1 1 0.6 0.6 ∞
Test sample related
16 Device positioning 3.8 N 1 1 1 3.8 3.8 99
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 18 / 126
17 Device holder 5.1 N 1 1 1 5.1 5.1 5
18 Drift of output power 5.0 R
1 1 2.9 2.9 ∞
Phantom and set-up
19 Phantom uncertainty 4.0 R
1 1 2.3 2.3 ∞
20 Liquid conductivity
(target) 5.0 R
0.64 0.43 1.8 1.2 ∞
21 Liquid conductivity
(meas) 2.5 N 1 0.64 0.43 1.6 1.2 ∞
22 Liquid Permittivity
(target) 5.0 R
0.6 0.49 1.7 1.5 ∞
23 Liquid Permittivity
(meas) 2.5 N 1 0.6 0.49 1.5 1.2 ∞
Combined standard RSS
n
i
iiCUCU
1
22 12.2% 11.9% 236
Expanded uncertainty
(P=95%) U = k
CU ,k=2 24.4% 23.8%
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 19 / 126
9. Conducted Power Measurement:
Band Channel Frequency (MHz) Output Power(dBm)
Maximum Power <SIM 1>
GSM900
CH975 880.2 31.92
CH37 897.4 31.83
CH124 914.8 31.82
GPRS900
(1Slot)
CH975 880.2 31.89
CH37 897.4 31.85
85 CH124 914.8 31.80
GPRS900
(2Slot)
CH975 880.2 30.88
CH37 897.4 30.74
CH124 914.8 30.68
GPRS900
(3Slot)
CH975 880.2 28.70
CH37 897.4 28.69
CH124 914.8 28.80
GPRS900
(4Slot)
CH975 880.2 27.70
CH37 897.4 27.56
CH124 914.8 27.57
DCS1800
CH512 1710.2 30.62
CH698 1747.4 30.64
CH885 1784.8 30.66
GPRS1800
(1Slot)
CH512 1710.2 30.62
CH698 1747.4 30.66
CH885 1784.8 30.67
GPRS1800
(2Slot)
CH512 1710.2 29.72
CH698 1747.4 29.69
CH885 1784.8 29.71
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 20 / 126
Band Channel Frequency (MHz) Output Power(dBm)
GPRS1800
(3Slot)
CH512 1710.2 27.98
CH698 1747.4 27.90
CH885 1784.8 27.92
GPRS1800
(4Slot)
CH512 1710.2 27.11
CH698 1747.4 27.02
CH885 1784.8 27.05
WCDMA
Band I
CH9612 1922.4 22.53
CH9750 1950.0 21.99
CH9888 1977.6 21.96
HSDPA
Band I
Sub type-1
CH9612 1922.4 21.59
CH9750 1950.0 21.10
CH9888 1977.6 21.03
HSDPA
Band I
Sub type-2
CH9612 1922.4 21.18
CH9750 1950.0 20.70
CH9888 1977.6 20.67
HSDPA
Band I
Sub type-3
CH9612 1922.4 19.40
CH9750 1950.0 18.87
CH9888 1977.6 19.02
HSDPA
Band I
Sub type-4
CH9612 1922.4 19.37
CH9750 1950.0 18.89
CH9888 1977.6 18.97
HSUPA
Band I
Sub type-1
CH9612 1922.4 21.48
CH9750 1950.0 20.96
CH9888 1977.6 20.95
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 21 / 126
HSUPA
Band I
Sub type-2
CH9612 1922.4 21.57
CH9750 1950.0 21.05
CH9888 1977.6 20.96
HSUPA
Band I
Sub type-3
CH9612 1922.4 19.58
CH9750 1950.0 19.09
CH9888 1977.6 19.13
HSUPA
Band I
Sub type-4
CH9612 1922.4 21.58
CH9750 1950.0 21.13
CH9888 1977.6 21.02
HSUPA
Band I
Sub type-5
CH9612 1922.4 20.49
CH9750 1950.0 20.05
CH9888 1977.6 20.06
Maximum Power <SIM 2>
GSM900 CH37 897.4 32.01
DCS1800 CH698 1747.4 26.89
WCDMA
Band I CH9750 1950.0 22.06
WIFI Maximum Power
802.11b
CH01 2412 13.22
CH07 2442 13.22
CH13 2472 13.42
802.11g
CH01 2412 10.05
CH07 2442 11.31
CH13 2472 11.57
802.11n20
CH01 2412 9.96
CH07 2442 11.45
CH13 2472 11.54
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 22 / 126
802.11n40
CH03 2422 7.87
CH07 2442 10.14
CH09 2462 10.29
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 23 / 126
10. Test photos and results:
10.1 DUT photos:
Front side
Back side
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 24 / 126
10.2 Setup photos:
Left Touch Cheek
Left Tilt(15°)
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 25 / 126
Right Touch Cheek
Right Tilt(15°)
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 26 / 126
Body Front
Body Worn
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 27 / 126
Body Worn with Headset
Side1
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 28 / 126
Side2
Side3
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 29 / 126
Side4
Side5
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 30 / 126
Side6
Liquid depth (15cm)
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 31 / 126
Wifi Configuration:
Model 802.11b
rate 1Mbps
Duty cycle 100%
Power 19dBm
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 32 / 126
10.3 SAR result summary:
Head
Test Case of Head
Result (mW/g)
10g Average
Power
Drift
<±0.2
dB
Date
Slot Band Test
Position Liquid Channel
SIM1
GSM 900
Left Cheek
Head
CH37 0.128 -0.024 Plot 1
Left Tilt CH37 0.075 0.106 Plot 2
Right Cheek CH37 0.120 0.025 Plot 3
Right Tilt CH37 0.070 -0.104 Plot 4
SIM2:
GSM 900 Left Cheek Head CH37 0.111 -0.102 Plot 5
SIM1:
GSM
1800
Left Cheek
Head
CH698 0.132 0.123 Plot 6
Left Tilt CH698 0.051 -0.024 Plot 7
Right Cheek CH698 0.125 0.103 Plot 8
Right Tilt CH698 0.041 0.072 Plot 9
SIM2:
GSM
1800 Left Cheek Head CH698 0.103 -0.038 Plot 10
SIM1:
WCDMA
Band I
Left Cheek
Head
CH9750 0.111 0.020 Plot 11
Left Tilt CH9750 0.055 0.072 Plot 12
Right Cheek CH9750 0.094 0.012 Plot 13
Right Tilt CH9750 0.038 0.112 Plot 14
SIM2:
WCDMA
Band1 Left Cheek Head CH9750 0.127 0.025 Plot 15
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 33 / 126
Body (15mm between DUT and Flat Phantom)
Note: When the 10g SAR is ≤1.0 mW/g,testing for low and high channel is optional.
Test Case of Body Result (mW/g)
10g Average
Power
Drift
<±0.2
dB
Date
Slot Band
Test
Position Liquid Channel
GRPS 900
Worn-2slot
Body
CH37 0.276 0.053 Plot 16
Worn-3slot CH37 0.259 -0.084 Plot 17
Worn-4slot CH37 0.265 -0.052 Plot 18
Front-4slot CH37 0.176 0.110 Plot 19
GRPS 1800
Worn-2slot
Body
CH698 0.210 0.110 Plot 20
Worn-3slot CH698 0.217 0.101 Plot 21
Worn-4slot CH698 0.237 0.018 Plot 22
Front-4slot CH698 0.164 0.019 Plot 23
GSM900 Worn-
Headset
Body
CH37 0.220 -0.130 Plot 24
GSM1800 Worn-
Headset CH698 0.146 0.017 Plot 25
WCDMA
Band I
Worn-
Headset CH9500 0.265 0.024 Plot 26
802.11b
Side 1
Body
Ch07 0.092 0.067 Plot 27
Side 2 Ch07 0.132 0.070 Plot 28
Side 3 CH07 0.127 0.121 Plot 29
Side 4 CH07 0.066 0.083 Plot 30
Side 5 CH07 0.274 0.108 Plot 31
Side6 CH07 0.009 -0.040 Plot 32
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 34 / 126
11. Equipment List:
NO. Instrument Manufacture
r
Model S/N Cal. Date Cal. Due Date
1 Communication
Tester Agilent E5515C MY50267264 Dec 27
th 2013 Dec 27
th 2014
2 E-field Probe Speag ES3DV3 3028 August 5th
2013 August 4th
2014
3 Dielectric Probe
Kit Speag
DAK 3.5mm
Probe 1038 N/A N/A
4 DAE Speag DAE4 689 July 20th
2013 July 19th
2014
5 SAM TWIN
phantom Speag SAM 1360/1432 N/A N/A
6 Robot Stabuli TX60L N/A N/A N/A
7 Device Holder Speag SD000H01HA N/A N/A N/A
8 Vector Network Agilent E5071C MY46107615 Jan 6th
2014 Jan 7th
2015
9 Signal Generator Agilent E4438C MY49072279 Nov 27th
2013 Nov 27th
2014
10 Amplifier Mini-circult ZHL-42W QA098002 N/A N/A
11 Power Meter Agilent N1419A MY50001563 Nov 27th
2013 Nov 27th
2014
12 Power Sensor Agilent N8481H MY51020010 Nov 27th
2013 Nov 27th
2014
13 Directional
Coupler Agilent 772D MY46151275 Nov 27
th 2013 Nov 27
th 2014
14 Directional
Coupler Agilent 778D MY48220607 Nov 27
th 2013 Nov 27
th 2014
15 Dipole 900MHz Speag D900V2 1d086 Aug 9th
2013 Aug 9th
2015
16 Dipole 1750MHz Speag D1750V2 1021 Aug 2nd
2013 Aug 2nd
2015
17 Dipole 1900MHz Speag D1900V2 5d175 June 10th
2013 June 10th
2015
18 Dipole 2450MHz Speag D2450V2 910 June 7th
2013 June 7th
2015
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 35 / 126
Appendix A. System validation plots:
DUT: Dipole 900MHz; Type: D900V2; Serial: D900V2 - SN: 1d086
Program Name: System Performance Check at 900 MHz
Communication System: CW; Frequency: 900 MHz;Duty Cycle: 1:1
Medium parameters used: f = 900 MHz; σ = 0.98 mho/m; εr = 42.14; ρ = 1000 kg/m3
Phantom section: Flat Section
DASY4 Configuration:
- Probe: ES3DV3 - SN3028; ConvF(4.08, 4.08, 4.08); Calibrated:8/5/2013
- Sensor-Surface: 4mm (Mechanical Surface Detection)
- Electronics: DAE4 Sn689; Calibrated: 7/20/2013
- Phantom: SAM with TP1432; Type: SAM
- Measurement SW: DASY4, V4.7 Build 53; Postprocessing SW: SEMCAD, V1.8 Build 172
d=10mm, Pin=250mW/Area Scan (61x61x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 2.82 mW/g
d=10mm, Pin=250mW/Zoom Scan (7x7x7) (7x7x7)/Cube 0: Measurement grid:
dx=5mm, dy=5mm, dz=5mm
Reference Value = 54.523 V/m; Power Drift = -0.01dB
Peak SAR (extrapolated) = 4.068 W/kg
SAR(1 g) = 2.68 mW/g; SAR(10 g) = 1.73 mW/g
Maximum value of SAR (measured) = 2.90 mW/g
0 dB = 2.90mW/g
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 36 / 126
DUT: Dipole 1750 MHz; Type: D1750V2; Serial: D1750V2 - SN: 1021
Program Name: System Performance Check at 1750 MHz
Communication System: CW; Frequency: 1750 MHz;Duty Cycle: 1:1
Medium parameters used: f = 1750 MHz; σ = 1.39 mho/m; εr = 39.84; ρ = 1000 kg/m3
Phantom section: Flat Section
DASY4 Configuration:
- Probe: ES3DV3 - SN3028; ConvF(4.08, 4.08, 4.08); Calibrated:8/5/2013
- Sensor-Surface: 4mm (Mechanical Surface Detection)
- Electronics: DAE4 Sn689; Calibrated: 7/20/2013
- Phantom: SAM with TP1432; Type: SAM
- Measurement SW: DASY4, V4.7 Build 53; Postprocessing SW: SEMCAD, V1.8 Build 172
d=15mm, Pin=250mW/Area Scan (61x101x1): Measurement grid: dx=15mm,
dy=15mm
Maximum value of SAR (interpolated) = 8.60 mW/g
d=15mm, Pin=250mW/Zoom Scan (7x7x7) (7x7x7)/Cube 0: Measurement grid:
dx=5mm, dy=5mm, dz=5mm
Reference Value = 83.712 V/m; Power Drift = 0.03dB
Peak SAR (extrapolated) = 16.718 W/kg
SAR(1 g) = 8.83 mW/g; SAR(10 g) = 4.57 mW/g
Maximum value of SAR (measured) = 9.93 mW/g
0 dB = 9.93mW/g
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 37 / 126
DUT: Dipole 1900 MHz; Type: D1900V2; Serial: D1900V2 - SN: 5d175
Program Name: System Performance Check at 1900 MHz
Communication System: CW; Frequency: 1900 MHz;Duty Cycle: 1:1
Medium parameters used: f = 1900 MHz; σ = 1.44 mho/m; εr = 39.39; ρ = 1000 kg/m3
Phantom section: Flat Section
DASY4 Configuration:
- Probe: ES3DV3 - SN3028; ConvF(4.08, 4.08, 4.08); Calibrated:8/5/2013
- Sensor-Surface: 4mm (Mechanical Surface Detection)
- Electronics: DAE4 Sn689; Calibrated: 7/20/2013
- Phantom: SAM with TP1432; Type: SAM
- Measurement SW: DASY4, V4.7 Build 53; Postprocessing SW: SEMCAD, V1.8 Build 172
d=15mm, Pin=250mW/Area Scan (61x101x1): Measurement grid: dx=15mm,
dy=15mm
Maximum value of SAR (interpolated) = 10 mW/g
d=15mm, Pin=250mW/Zoom Scan (7x7x7) (7x7x7)/Cube 0: Measurement grid:
dx=5mm, dy=5mm, dz=5mm
Reference Value = 86.925 V/m; Power Drift = 0.11dB
Peak SAR (extrapolated) = 19.256 W/kg
SAR(1 g) = 9.93 mW/g; SAR(10 g) = 5.02 mW/g
Maximum value of SAR (measured) = 11.2 mW/g
0 dB = 11.2mW/g
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 38 / 126
DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 - SN: 910
Program Name: System Performance Check Body at 2450 MHz
Communication System: CW; Frequency: 2450 MHz;Duty Cycle: 1:1
Medium parameters used: f = 2450 MHz; σ = 1.81 mho/m; εr = 39.6; ρ = 1000 kg/m3
Phantom section: Flat Section
DASY4 Configuration:
- Probe: ES3DV3 - SN3028; ConvF(4.08, 4.08, 4.08); Calibrated:8/5/2013
- Sensor-Surface: 4mm (Mechanical Surface Detection)
- Electronics: DAE4 Sn689; Calibrated: 7/20/2013
- Phantom: SAM with TP1432; Type: SAM
- Measurement SW: DASY4, V4.7 Build 53; Postprocessing SW: SEMCAD, V1.8 Build 172
d=15mm, Pin=250mW/Area Scan (61x101x1): Measurement grid: dx=15mm,
dy=15mm
Maximum value of SAR (interpolated) = 14 mW/g
d=15mm, Pin=250mW/Zoom Scan (7x7x7) (7x7x7)/Cube 0: Measurement grid:
dx=5mm, dy=5mm, dz=5mm
Reference Value = 84.1 V/m; Power Drift = 0.029dB
Peak SAR (extrapolated) = 25.6 W/kg
SAR(1 g) = 12.5 mW/g; SAR(10 g) = 5.72 mW/g
Maximum value of SAR (measured) = 14.3 mW/g
0 dB = 14.4mW/g
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 39 / 126
Appendix B. SAR Test plots:
Plot1: Date/Time: 6/13/2014 9:29:42 AM
Test Laboratory: SUNWAY COMMUNICATION CO.,LTD.
DUT: Thc4400; Type: Mobile phone
Program Name: Thc4400
Communication System: GSM 900; Frequency: 897.4 MHz;Duty Cycle: 1:8.3
Medium parameters used (interpolated): f = 897.4 MHz; σ = 0.948 mho/m; εr = 41.2; ρ = 1000
kg/m3 Phantom section: Left Section
DASY4 Configuration:
- Probe: ES3DV3 - SN3028; ConvF(6.28, 6.28, 6.28); Calibrated: 8/5/2013
- Sensor-Surface: 4mm (Mechanical Surface Detection)
- Electronics: DAE4 Sn689; Calibrated: 7/20/2013
- Phantom: SAM with TP1432; Type: SAM; Serial: Not Specified
- Measurement SW: DASY4, V4.7 Build 53; Postprocessing SW: SEMCAD, V1.8 Build 172
Left touch/Area Scan (71x131x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 0.176 mW/g
Left touch/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm,
dz=5mm
Reference Value = 4.63 V/m; Power Drift = -0.024 dB
Peak SAR (extrapolated) = 0.196 W/kg
SAR(1 g) = 0.165 mW/g; SAR(10 g) = 0.128 mW/g
Maximum value of SAR (measured) = 0.174 mW/g
0 dB = 0.174mW/g
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 40 / 126
Plot2: Date/Time: 6/13/2014 9:40:01AM
Test Laboratory: SUNWAY COMMUNICATION CO.,LTD.
DUT: Thc4400; Type: Mobile phone
Program Name: Thc4400
Communication System: GSM 900; Frequency: 897.4 MHz;Duty Cycle: 1:8.3
Medium parameters used (interpolated): f = 897.4 MHz; σ = 0.948 mho/m; εr = 41.2; ρ = 1000
kg/m3
Phantom section: Left Section
DASY4 Configuration:
- Probe: ES3DV3 - SN3028; ConvF(6.28, 6.28, 6.28); Calibrated: 8/5/2013
- Sensor-Surface: 4mm (Mechanical Surface Detection)
- Electronics: DAE4 Sn689; Calibrated: 7/20/2013
- Phantom: SAM with TP1432; Type: SAM; Serial: Not Specified
- Measurement SW: DASY4, V4.7 Build 53; Postprocessing SW: SEMCAD, V1.8 Build 172
Left tilt/Area Scan (71x131x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 0.098 mW/g
Left tilt/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 8.41 V/m; Power Drift = 0.106 dB
Peak SAR (extrapolated) = 0.117 W/kg
SAR(1 g) = 0.096 mW/g; SAR(10 g) = 0.075 mW/g
Maximum value of SAR (measured) = 0.103 mW/g
0 dB = 0.103mW/g
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 41 / 126
Plot3: Date/Time: 6/13/2014 10:10:01AM
Test Laboratory: SUNWAY COMMUNICATION CO.,LTD.
DUT: Thc4400; Type: Mobile phone
Program Name: Thc4400
Communication System: GSM 900; Frequency: 897.4 MHz;Duty Cycle: 1:8.3
Medium parameters used (interpolated): f = 897.4 MHz; σ = 0.948 mho/m; εr = 41.2; ρ = 1000
kg/m3
Phantom section: Right Section
DASY4 Configuration:
- Probe: ES3DV3 - SN3028; ConvF(6.28, 6.28, 6.28); Calibrated: 8/5/2013
- Sensor-Surface: 4mm (Mechanical Surface Detection)
- Electronics: DAE4 Sn689; Calibrated: 7/20/2013
- Phantom: SAM with TP1432; Type: SAM; Serial: Not Specified
- Measurement SW: DASY4, V4.7 Build 53; Postprocessing SW: SEMCAD, V1.8 Build 172
Right touch/Area Scan (71x131x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 0.291 mW/g
Right touch/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm,
dz=5mm
Reference Value = 6.06 V/m; Power Drift = 0.025 dB
Peak SAR (extrapolated) = 0.202 W/kg
SAR(1 g) = 0.167 mW/g; SAR(10 g) = 0.120 mW/g
Maximum value of SAR (measured) = 0.181 mW/g
0 dB = 0.181mW/g
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 42 / 126
Plot4: Date/Time: 6/13/2014 10:25:12AM
Test Laboratory: SUNWAY COMMUNICATION CO.,LTD.
DUT: Thc4400; Type: Mobile phone
Program Name: Thc4400
Communication System: GSM 900; Frequency: 897.4 MHz;Duty Cycle: 1:8.3
Medium parameters used (interpolated): f = 897.4 MHz; σ = 0.948 mho/m; εr = 41.2; ρ = 1000
kg/m3
Phantom section: Right Section
DASY4 Configuration:
- Probe: ES3DV3 - SN3028; ConvF(6.28, 6.28, 6.28); Calibrated: 8/5/2013
- Sensor-Surface: 4mm (Mechanical Surface Detection)
- Electronics: DAE4 Sn689; Calibrated: 7/20/2013
- Phantom: SAM with TP1432; Type: SAM; Serial: Not Specified
- Measurement SW: DASY4, V4.7 Build 53; Postprocessing SW: SEMCAD, V1.8 Build 172
Right tilt/Area Scan (71x131x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 0.096 mW/g
Right tilt/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 8.75 V/m; Power Drift = -0.104 dB
Peak SAR (extrapolated) = 0.110 W/kg
SAR(1 g) = 0.091 mW/g; SAR(10 g) = 0.070 mW/g
Maximum value of SAR (measured) = 0.095 mW/g
0 dB = 0.095mW/g
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 43 / 126
Plot5: Date/Time: 6/13/2014 10:45:12AM
Test Laboratory: SUNWAY COMMUNICATION CO.,LTD.
DUT: Thc4400; Type: Mobile phone
Program Name: Thc4400
Communication System: GSM 900; Frequency: 897.4 MHz;Duty Cycle: 1:8.3
Medium parameters used (interpolated): f = 897.4 MHz; σ = 0.948 mho/m; εr = 41.2; ρ = 1000
kg/m3
Phantom section: Left Section
DASY4 Configuration:
- Probe: ES3DV3 - SN3028; ConvF(6.28, 6.28, 6.28); Calibrated: 8/5/2013
- Sensor-Surface: 4mm (Mechanical Surface Detection)
- Electronics: DAE4 Sn689; Calibrated: 7/20/2013
- Phantom: SAM with TP1432; Type: SAM
- Measurement SW: DASY4, V4.7 Build 53; Postprocessing SW: SEMCAD, V1.8 Build 172
Left touch/Area Scan (71x131x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 0.157 mW/g
Left touch/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 8.35 V/m; Power Drift = -0.102 dB
Peak SAR (extrapolated) = 0.168 W/kg
SAR(1 g) = 0.144 mW/g; SAR(10 g) = 0.111 mW/g
Maximum value of SAR (measured) = 0.151 mW/g
0 dB = 0.151mW/g
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 44 / 126
Plot6: Date/Time: 6/13/2014 11:15:01AM
Test Laboratory: SUNWAY COMMUNICATION CO.,LTD.
DUT: Thc4400; Type: Mobile phone
Program Name: Thc4400
Communication System: GSM 1800; Frequency: 1747.4 MHz;Duty Cycle: 1:8.3
Medium parameters used: f = 1800 MHz; σ = 1.33 mho/m; εr = 40.8; ρ = 1000 kg/m3
Phantom section: Left Section
DASY4 Configuration:
- Probe: ES3DV3 - SN3028; ConvF(5.62, 5.62, 5.62); Calibrated: 8/5/2013
- Sensor-Surface: 4mm (Mechanical Surface Detection)
- Electronics: DAE4 Sn689; Calibrated: 7/20/2013
- Phantom: SAM with TP1360; Type: SAM; Serial: Not Specified
- Measurement SW: DASY4, V4.7 Build 53; Postprocessing SW: SEMCAD, V1.8 Build 172
Left touch/Area Scan (71x131x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 0.235 mW/g
Left touch/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 4.61 V/m; Power Drift = 0.123 dB
Peak SAR (extrapolated) = 0.293 W/kg
SAR(1 g) = 0.206 mW/g; SAR(10 g) = 0.132 mW/g
Maximum value of SAR (measured) = 0.223 mW/g
0 dB = 0.223mW/g
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 45 / 126
Plot7: Date/Time: 6/13/2014 11:25:11AM
Test Laboratory: SUNWAY COMMUNICATION CO.,LTD.
DUT: Thc4400; Type: Mobile phone
Program Name: Thc4400
Communication System: GSM 1800; Frequency: 1747.4 MHz;Duty Cycle: 1:8.3
Medium parameters used: f = 1800 MHz; σ = 1.33 mho/m; εr = 40.8; ρ = 1000 kg/m3
Phantom section: Left Section
DASY4 Configuration:
- Probe: ES3DV3 - SN3028; ConvF(5.62, 5.62, 5.62); Calibrated: 8/5/2013
- Sensor-Surface: 4mm (Mechanical Surface Detection)
- Electronics: DAE4 Sn689; Calibrated: 7/20/2013
- Phantom: SAM with TP1360; Type: SAM; Serial: Not Specified
- Measurement SW: DASY4, V4.7 Build 53; Postprocessing SW: SEMCAD, V1.8 Build 172
Left tilt/Area Scan (71x131x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 0.099 mW/g
Left tilt/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 7.23 V/m; Power Drift = -0.024 dB
Peak SAR (extrapolated) = 0.127 W/kg
SAR(1 g) = 0.081 mW/g; SAR(10 g) = 0.051 mW/g
Maximum value of SAR (measured) = 0.088 mW/g
0 dB = 0.088mW/g
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 46 / 126
Plot8: Date/Time: 6/13/2014 11:55:42AM
Test Laboratory: SUNWAY COMMUNICATION CO.,LTD.
DUT: Thc4400; Type: Mobile phone
Program Name: Thc4400
Communication System: GSM 1800; Frequency: 1747.4 MHz;Duty Cycle: 1:8.3
Medium parameters used: f = 1800 MHz; σ = 1.33 mho/m; εr = 40.8; ρ = 1000 kg/m3
Phantom section: Right Section
DASY4 Configuration:
- Probe: ES3DV3 - SN3028; ConvF(5.62, 5.62, 5.62); Calibrated: 8/5/2013
- Sensor-Surface: 4mm (Mechanical Surface Detection)
- Electronics: DAE4 Sn689; Calibrated: 7/20/2013
- Phantom: SAM with TP1360; Type: SAM; Serial: Not Specified
- Measurement SW: DASY4, V4.7 Build 53; Postprocessing SW: SEMCAD, V1.8 Build 172
Right touch/Area Scan (71x131x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 0.208 mW/g
Rght touch/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm,
dz=5mm
Reference Value = 5.57 V/m; Power Drift = 0.103 dB
Peak SAR (extrapolated) = 0.257 W/kg
SAR(1 g) = 0.190 mW/g; SAR(10 g) = 0.125 mW/g
Maximum value of SAR (measured) = 0.207 mW/g
0 dB = 0.207mW/g
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 47 / 126
Plot9: Date/Time: 6/13/2014 12:15:55PM
Test Laboratory: SUNWAY COMMUNICATION CO.,LTD.
DUT: Thc4400; Type: Mobile phone
Program Name: Thc4400
Communication System: GSM 1800; Frequency: 1747.4 MHz;Duty Cycle: 1:8.3
Medium parameters used: f = 1800 MHz; σ = 1.33 mho/m; εr = 40.8; ρ = 1000 kg/m3
Phantom section: Right Section
DASY4 Configuration:
- Probe: ES3DV3 - SN3028; ConvF(5.62, 5.62, 5.62); Calibrated: 8/5/2013
- Sensor-Surface: 4mm (Mechanical Surface Detection)
- Electronics: DAE4 Sn689; Calibrated: 7/20/2013
- Phantom: SAM with TP1360; Type: SAM; Serial: Not Specified
- Measurement SW: DASY4, V4.7 Build 53; Postprocessing SW: SEMCAD, V1.8 Build 172
Right tilt/Area Scan (71x131x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 0.073 mW/g
Right tilt/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 7.14 V/m; Power Drift = 0.072 dB
Peak SAR (extrapolated) = 0.095 W/kg
SAR(1 g) = 0.066 mW/g; SAR(10 g) = 0.041 mW/g
Maximum value of SAR (measured) = 0.072 mW/g
0 dB = 0.072mW/g
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 48 / 126
Plot10: Date/Time: 6/13/2014 12:30:10PM
Test Laboratory: SUNWAY COMMUNICATION CO.,LTD.
DUT: Thc4400; Type: Mobile phone
Program Name: Thc4400
Communication System: GSM 1800; Frequency: 1747.4 MHz;Duty Cycle: 1:8.3
Medium parameters used: f = 1800 MHz; σ = 1.33 mho/m; εr = 40.8; ρ = 1000 kg/m3
Phantom section: Left Section
DASY4 Configuration:
- Probe: ES3DV3 - SN3028; ConvF(5.62, 5.62, 5.62); Calibrated: 8/5/2013
- Sensor-Surface: 4mm (Mechanical Surface Detection)
- Electronics: DAE4 Sn689; Calibrated: 7/20/2013
- Phantom: SAM with TP1360; Type: SAM; Serial: Not Specified
- Measurement SW: DASY4, V4.7 Build 53; Postprocessing SW: SEMCAD, V1.8 Build 172
Left touch/Area Scan (71x131x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 0.238 mW/g
Left touch/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 5.82 V/m; Power Drift = -0.038dB
Peak SAR (extrapolated) = 0.223 W/kg
SAR(1 g) = 0.160 mW/g; SAR(10 g) = 0.103 mW/g
Maximum value of SAR (measured) = 0.175 mW/g
0 dB = 0.175mW/g
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 49 / 126
Plot11: Date/Time: 6/13/2014 12:50:05PM
Test Laboratory: SUNWAY COMMUNICATION CO.,LTD.
DUT: Thc4400; Type: Mobile phone
Program Name: Thc4400
Communication System: W2100; Frequency: 1950 MHz;Duty Cycle: 1:1
Medium parameters used: f = 1950 MHz; σ = 1.47 mho/m; εr = 40.2; ρ = 1000 kg/m3
Phantom section: Left Section
DASY4 Configuration:
- Probe: ES3DV3 - SN3028; ConvF(5.21, 5.21, 5.21); Calibrated: 8/5/2013
- Sensor-Surface: 4mm (Mechanical Surface Detection)
- Electronics: DAE4 Sn689; Calibrated: 7/20/2013
- Phantom: SAM with TP1360; Type: SAM;
- Measurement SW: DASY4, V4.7 Build 53; Postprocessing SW: SEMCAD, V1.8 Build 172
Left touch/Area Scan (71x131x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 0.201 mW/g
Left touch/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 4.79 V/m; Power Drift = 0.020 dB
Peak SAR (extrapolated) = 0.276 W/kg
SAR(1 g) = 0.184 mW/g; SAR(10 g) = 0.111 mW/g
Maximum value of SAR (measured) = 0.201 mW/g
0 dB = 0.201mW/g
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 50 / 126
Plot12: Date/Time: 6/13/2014 13:13:02PM
Test Laboratory: SUNWAY COMMUNICATION CO.,LTD.
DUT: Thc4400; Type: Mobile phone
Program Name: Thc4400
Communication System: W2100; Frequency: 1950 MHz;Duty Cycle: 1:1
Medium parameters used: f = 1950 MHz; σ = 1.47 mho/m; εr = 40.2; ρ = 1000 kg/m3
Phantom section: Left Section
DASY4 Configuration:
- Probe: ES3DV3 - SN3028; ConvF(5.21, 5.21, 5.21); Calibrated: 8/5/2013
- Sensor-Surface: 4mm (Mechanical Surface Detection)
- Electronics: DAE4 Sn689; Calibrated: 7/20/2013
- Phantom: SAM with TP1360; Type: SAM;
- Measurement SW: DASY4, V4.7 Build 53; Postprocessing SW: SEMCAD, V1.8 Build 172
Left tilt/Area Scan (71x131x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 0.117 mW/g
Left tilt/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 6.89 V/m; Power Drift = 0.072 dB
Peak SAR (extrapolated) = 0.141 W/kg
SAR(1 g) = 0.091 mW/g; SAR(10 g) = 0.055 mW/g
Maximum value of SAR (measured) = 0.100 mW/g
0 dB = 0.100mW/g
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 51 / 126
Plot13: Date/Time: 6/13/2014 13:26:20PM
Test Laboratory: SUNWAY COMMUNICATION CO.,LTD.
DUT: Thc4400; Type: Mobile phone
Program Name: Thc4400
Communication System: W2100; Frequency: 1950 MHz;Duty Cycle: 1:1
Medium parameters used: f = 1950 MHz; σ = 1.47 mho/m; εr = 40.2; ρ = 1000 kg/m3
Phantom section: Right Section
DASY4 Configuration:
- Probe: ES3DV3 - SN3028; ConvF(5.21, 5.21, 5.21); Calibrated: 8/5/2013
- Sensor-Surface: 4mm (Mechanical Surface Detection)
- Electronics: DAE4 Sn689; Calibrated: 7/20/2013
- Phantom: SAM with TP1360; Type: SAM;
- Measurement SW: DASY4, V4.7 Build 53; Postprocessing SW: SEMCAD, V1.8 Build 172
Right touch/Area Scan (71x131x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 0.170 mW/g
Right touch/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm,
dz=5mm
Reference Value = 4.43 V/m; Power Drift = 0.012 dB
Peak SAR (extrapolated) = 0.223 W/kg
SAR(1 g) = 0.151 mW/g; SAR(10 g) = 0.094 mW/g
Maximum value of SAR (measured) = 0.167 mW/g
0 dB = 0.167mW/g
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 52 / 126
Plot14: Date/Time: 6/13/2014 13:45:15PM
Test Laboratory: SUNWAY COMMUNICATION CO.,LTD.
DUT: Thc4400; Type: Mobile phone
Program Name: Thc4400
Communication System: W2100; Frequency: 1950 MHz;Duty Cycle: 1:1
Medium parameters used: f = 1950 MHz; σ = 1.47 mho/m; εr = 40.2; ρ = 1000 kg/m3
Phantom section: Right Section
DASY4 Configuration:
- Probe: ES3DV3 - SN3028; ConvF(5.21, 5.21, 5.21); Calibrated: 8/5/2013
- Sensor-Surface: 4mm (Mechanical Surface Detection)
- Electronics: DAE4 Sn689; Calibrated: 7/20/2013
- Phantom: SAM with TP1360; Type: SAM;
- Measurement SW: DASY4, V4.7 Build 53; Postprocessing SW: SEMCAD, V1.8 Build 172
Right tilt/Area Scan (71x131x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 0.068 mW/g
Right tilt/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 6.76 V/m; Power Drift = 0.112 dB
Peak SAR (extrapolated) = 0.142 W/kg
SAR(1 g) = 0.071 mW/g; SAR(10 g) = 0.038 mW/g
Maximum value of SAR (measured) = 0.082 mW/g
0 dB = 0.082mW/g
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 53 / 126
Plot15: Date/Time: 6/13/2014 14:15:12PM
Test Laboratory: SUNWAY COMMUNICATION CO.,LTD.
DUT: Thc4400; Type: Mobile phone
Program Name: Thc4400
Communication System: W2100; Frequency: 1950 MHz;Duty Cycle: 1:1
Medium parameters used: f = 1950 MHz; σ = 1.47 mho/m; εr = 40.2; ρ = 1000 kg/m3
Phantom section: Left Section
DASY4 Configuration:
- Probe: ES3DV3 - SN3028; ConvF(5.21, 5.21, 5.21); Calibrated: 8/5/2013
- Sensor-Surface: 4mm (Mechanical Surface Detection)
- Electronics: DAE4 Sn689; Calibrated: 7/20/2013
- Phantom: SAM with TP1360; Type: SAM;
- Measurement SW: DASY4, V4.7 Build 53; Postprocessing SW: SEMCAD, V1.8 Build 172
Left touch/Area Scan (71x131x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 0.234 mW/g
Left touch/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 5.00 V/m; Power Drift = 0.025 dB
Peak SAR (extrapolated) = 0.317 W/kg
SAR(1 g) = 0.209 mW/g; SAR(10 g) = 0.127 mW/g
Maximum value of SAR (measured) = 0.231 mW/g
0 dB = 0.231mW/g
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 54 / 126
Plot16: Date/Time: 6/13/2014 14:40:10PM
Test Laboratory: SUNWAY COMMUNICATION CO.,LTD.
DUT: Thc4400; Type: Mobile phone
Program Name: Thc4400
Communication System: GPRS900; Frequency: 897.4 MHz;Duty Cycle: 1:2
Medium parameters used (interpolated): f = 897.4 MHz; σ = 0.948 mho/m; εr = 41.2; ρ = 1000
kg/m3
Phantom section: Flat Section
DASY4 Configuration:
- Probe: ES3DV3 - SN3028; ConvF(6.29, 6.29, 6.29); Calibrated: 8/5/2013
- Sensor-Surface: 4mm (Mechanical Surface Detection)
- Electronics: DAE4 Sn689; Calibrated: 7/20/2013
- Phantom: SAM with TP1432; Type: SAM; Serial: Not Specified
- Measurement SW: DASY4, V4.7 Build 53; Postprocessing SW: SEMCAD, V1.8 Build 172
Worm 2sl/Area Scan (71x131x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 0.376 mW/g
Worm 2sl/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 19.8 V/m; Power Drift = 0.053 dB
Peak SAR (extrapolated) = 0.432 W/kg
SAR(1 g) = 0.359 mW/g; SAR(10 g) = 0.276 mW/g
Maximum value of SAR (measured) = 0.378 mW/g
0 dB = 0.378mW/g
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 55 / 126
Plot17: Date/Time: 6/13/2014 14:23:02PM
Test Laboratory: SUNWAY COMMUNICATION CO.,LTD.
DUT: Thc4400; Type: Mobile phone
Program Name: Thc4400
Communication System: GPRS900; Frequency: 897.4 MHz;Duty Cycle: 1:2
Medium parameters used (interpolated): f = 897.4 MHz; σ = 0.948 mho/m; εr = 41.2; ρ = 1000
kg/m3
Phantom section: Flat Section
DASY4 Configuration:
- Probe: ES3DV3 - SN3028; ConvF(6.29, 6.29, 6.29); Calibrated: 8/5/2013
- Sensor-Surface: 4mm (Mechanical Surface Detection)
- Electronics: DAE4 Sn689; Calibrated: 7/20/2013
- Phantom: SAM with TP1432; Type: SAM; Serial: Not Specified
- Measurement SW: DASY4, V4.7 Build 53; Postprocessing SW: SEMCAD, V1.8 Build 172
Worn 3sl/Area Scan (71x131x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 0.354 mW/g
Worn 3sl/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 18.9 V/m; Power Drift = 0.084 dB
Peak SAR (extrapolated) = 0.405 W/kg
SAR(1 g) = 0.337 mW/g; SAR(10 g) = 0.259 mW/g
Maximum value of SAR (measured) = 0.354 mW/g
0 dB = 0.354mW/g
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 56 / 126
Plot18: Date/Time: 6/13/2014 15:02:01PM
Test Laboratory: SUNWAY COMMUNICATION CO.,LTD.
DUT: Thc4400; Type: Mobile phone
Program Name: Thc4400
Communication System: GPRS900; Frequency: 897.4 MHz;Duty Cycle: 1:2
Medium parameters used (interpolated): f = 897.4 MHz; σ = 0.948 mho/m; εr = 41.2; ρ = 1000
kg/m3 Phantom section: Flat Section
DASY4 Configuration:
- Probe: ES3DV3 - SN3028; ConvF(6.29, 6.29, 6.29); Calibrated: 8/5/2013
- Sensor-Surface: 4mm (Mechanical Surface Detection)
- Electronics: DAE4 Sn689; Calibrated: 7/20/2013
- Phantom: SAM with TP1432; Type: SAM; Serial: Not Specified
- Measurement SW: DASY4, V4.7 Build 53; Postprocessing SW: SEMCAD, V1.8 Build 172
Worn4sl/Area Scan (71x131x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 0.361 mW/g
Worn4sl/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 19.6 V/m; Power Drift = -0.052 dB
Peak SAR (extrapolated) = 0.428 W/kg
SAR(1 g) = 0.346 mW/g; SAR(10 g) = 0.265 mW/g
Maximum value of SAR (measured) = 0.369 mW/g
0 dB = 0.369mW/g
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 57 / 126
Plot19: Date/Time: 6/13/2014 15:20:20OM
Test Laboratory: SUNWAY COMMUNICATION CO.,LTD.
DUT: Thc4400; Type: Mobile phone
Program Name: Thc4400
Communication System: GPRS900; Frequency: 897.4 MHz;Duty Cycle: 1:2
Medium parameters used (interpolated): f = 897.4 MHz; σ = 0.948 mho/m; εr = 41.2; ρ = 1000
kg/m3
Phantom section: Flat Section
DASY4 Configuration:
- Probe: ES3DV3 - SN3028; ConvF(6.29, 6.29, 6.29); Calibrated: 8/5/2013
- Sensor-Surface: 4mm (Mechanical Surface Detection)
- Electronics: DAE4 Sn689; Calibrated: 7/20/2013
- Phantom: SAM with TP1432; Type: SAM; Serial: Not Specified
- Measurement SW: DASY4, V4.7 Build 53; Postprocessing SW: SEMCAD, V1.8 Build 172
Front 4sl/Area Scan (71x131x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 0.228 mW/g
Front 4sl/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 15.3 V/m; Power Drift = 0.110 dB
Peak SAR (extrapolated) = 0.266 W/kg
SAR(1 g) = 0.219 mW/g; SAR(10 g) = 0.176 mW/g
Maximum value of SAR (measured) = 0.233 mW/g
0 dB = 0.233mW/g
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 58 / 126
Plot20: Date/Time: 6/13/2014 16:15:02PM
Test Laboratory: SUNWAY COMMUNICATION CO.,LTD.
DUT: Thc4400; Type: Mobile phone
Program Name: Thc4400
Communication System: GPRS 1800; Frequency: 1747.4 MHz;Duty Cycle: 1:2
Medium parameters used: f = 1800 MHz; σ = 1.33 mho/m; εr = 40.8; ρ = 1000 kg/m3
Phantom section: Flat Section
DASY4 Configuration:
- Probe: ES3DV3 - SN3028; ConvF(5.15, 5.15, 5.15); Calibrated: 8/5/2013
- Sensor-Surface: 4mm (Mechanical Surface Detection)
- Electronics: DAE4 Sn689; Calibrated: 7/20/2013
- Phantom: SAM with TP1360; Type: SAM; Serial: Not Specified
- Measurement SW: DASY4, V4.7 Build 53; Postprocessing SW: SEMCAD, V1.8 Build 172
Worm 2sl/Area Scan (71x131x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 0.387 mW/g
Worm 2sl/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 6.94 V/m; Power Drift = 0.110 dB
Peak SAR (extrapolated) = 0.523 W/kg
SAR(1 g) = 0.347 mW/g; SAR(10 g) = 0.210 mW/g
Maximum value of SAR (measured) = 0.382 mW/g
0 dB = 0.382mW/g
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 59 / 126
Plot21: Date/Time: 6/13/2014 16:32:10PM
Test Laboratory: SUNWAY COMMUNICATION CO.,LTD.
DUT: Thc4400; Type: Mobile phone
Program Name: Thc4400
Communication System: GPRS 1800; Frequency: 1747.4 MHz;Duty Cycle: 1:2
Medium parameters used: f = 1800 MHz; σ = 1.33 mho/m; εr = 40.8; ρ = 1000 kg/m3
Phantom section: Flat Section
DASY4 Configuration:
- Probe: ES3DV3 - SN3028; ConvF(5.15, 5.15, 5.15); Calibrated: 8/5/2013
- Sensor-Surface: 4mm (Mechanical Surface Detection)
- Electronics: DAE4 Sn689; Calibrated: 7/20/2013
- Phantom: SAM with TP1360; Type: SAM; Serial: Not Specified
- Measurement SW: DASY4, V4.7 Build 53; Postprocessing SW: SEMCAD, V1.8 Build 172
Worn 3sl/Area Scan (71x131x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 0.390 mW/g
Worn 3sl/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 7.04 V/m; Power Drift = 0.101 dB
Peak SAR (extrapolated) = 0.538 W/kg
SAR(1 g) = 0.358 mW/g; SAR(10 g) = 0.217 mW/g
Maximum value of SAR (measured) = 0.393 mW/g
0 dB = 0.393mW/g
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 60 / 126
Plot22: Date/Time: 6/13/2014 16:55:03PM
Test Laboratory: SUNWAY COMMUNICATION CO.,LTD.
DUT: Thc4400; Type: Mobile phone
Program Name: Thc4400
Communication System: GPRS 1800; Frequency: 1747.4 MHz;Duty Cycle: 1:2
Medium parameters used: f = 1800 MHz; σ = 1.33 mho/m; εr = 40.8; ρ = 1000 kg/m3
Phantom section: Flat Section
DASY4 Configuration:
- Probe: ES3DV3 - SN3028; ConvF(5.15, 5.15, 5.15); Calibrated: 8/5/2013
- Sensor-Surface: 4mm (Mechanical Surface Detection)
- Electronics: DAE4 Sn689; Calibrated: 7/20/2013
- Phantom: SAM with TP1360; Type: SAM; Serial: Not Specified
- Measurement SW: DASY4, V4.7 Build 53; Postprocessing SW: SEMCAD, V1.8 Build 172
Worn4sl/Area Scan (71x131x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 0.429 mW/g
Worn4sl/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 7.29 V/m; Power Drift = 0.018 dB
Peak SAR (extrapolated) = 0.597 W/kg
SAR(1 g) = 0.393 mW/g; SAR(10 g) = 0.237 mW/g
Maximum value of SAR (measured) = 0.433 mW/g
0 dB = 0.433mW/g
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 61 / 126
Plot23: Date/Time: 6/13/2014 17:30:22PM
Test Laboratory: SUNWAY COMMUNICATION CO.,LTD.
DUT: Thc4400; Type: Mobile phone
Program Name: Thc4400
Communication System: GPRS 1800; Frequency: 1747.4 MHz;Duty Cycle: 1:2
Medium parameters used: f = 1800 MHz; σ = 1.33 mho/m; εr = 40.8; ρ = 1000 kg/m3
Phantom section: Flat Section
DASY4 Configuration:
- Probe: ES3DV3 - SN3028; ConvF(5.15, 5.15, 5.15); Calibrated: 8/5/2013
- Sensor-Surface: 4mm (Mechanical Surface Detection)
- Electronics: DAE4 Sn689; Calibrated: 7/20/2013
- Phantom: SAM with TP1360; Type: SAM; Serial: Not Specified
- Measurement SW: DASY4, V4.7 Build 53; Postprocessing SW: SEMCAD, V1.8 Build 172
Front 4sl/Area Scan (71x131x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 0.291 mW/g
Front 4sl/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 4.36 V/m; Power Drift = 0.019 dB
Peak SAR (extrapolated) = 0.388 W/kg
SAR(1 g) = 0.265 mW/g; SAR(10 g) = 0.164 mW/g
Maximum value of SAR (measured) = 0.291 mW/g
0 dB = 0.291mW/g
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 62 / 126
Plot24: Date/Time: 6/13/2014 17:30:22PM
Test Laboratory: SUNWAY COMMUNICATION CO.,LTD.
DUT: Thc4400; Type: Mobile phone
Program Name: Thc4400
Communication System: GSM 900; Frequency: 897.4 MHz;Duty Cycle: 1:8.3
Medium parameters used (interpolated): f = 897.4 MHz; σ = 0.948 mho/m; εr = 41.2; ρ = 1000
kg/m3
Phantom section: Flat Section
DASY4 Configuration:
- Probe: ES3DV3 - SN3028; ConvF(6.29, 6.29, 6.29); Calibrated: 8/5/2013
- Sensor-Surface: 4mm (Mechanical Surface Detection)
- Electronics: DAE4 Sn689; Calibrated: 7/20/2013
- Phantom: SAM with TP1432; Type: SAM;
- Measurement SW: DASY4, V4.7 Build 53; Postprocessing SW: SEMCAD, V1.8 Build 172
Worn-HS/Area Scan (71x131x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 0.300 mW/g
Worn-HS/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 18.1 V/m; Power Drift = -0.130 dB
Peak SAR (extrapolated) = 0.350 W/kg
SAR(1 g) = 0.287 mW/g; SAR(10 g) = 0.220 mW/g
Maximum value of SAR (measured) = 0.302 mW/g
0 dB = 0.302mW/g
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 63 / 126
Plot25: Date/Time: 6/13/2014 17:30:22PM
Test Laboratory: SUNWAY COMMUNICATION CO.,LTD.
DUT: Thc4400; Type: Mobile phone
Program Name: Thc4400
Communication System: GSM 1800; Frequency: 1747.4 MHz;Duty Cycle: 1:8.3
Medium parameters used: f = 1800 MHz; σ = 1.33 mho/m; εr = 40.8; ρ = 1000 kg/m3
Phantom section: Flat Section
DASY4 Configuration:
- Probe: ES3DV3 - SN3028; ConvF(5.15, 5.15, 5.15); Calibrated: 8/5/2013
- Sensor-Surface: 4mm (Mechanical Surface Detection)
- Electronics: DAE4 Sn689; Calibrated: 7/20/2013
- Phantom: SAM with TP1360; Type: SAM; Serial: Not Specified
- Measurement SW: DASY4, V4.7 Build 53; Postprocessing SW: SEMCAD, V1.8 Build 172
Worn-HS/Area Scan (71x131x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 0.264 mW/g
Worn-HS/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 6.05 V/m; Power Drift = 0.017 dB
Peak SAR (extrapolated) = 0.366 W/kg
SAR(1 g) = 0.242 mW/g; SAR(10 g) = 0.146 mW/g
Maximum value of SAR (measured) = 0.265 mW/g
0 dB = 0.265mW/g
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 64 / 126
Plot26: Date/Time: 6/13/2014 17:30:22PM
Test Laboratory: SUNWAY COMMUNICATION CO.,LTD.
DUT: Thc4400; Type: Mobile phone
Program Name: Thc4400
Communication System: W2100; Frequency: 1950 MHz;Duty Cycle: 1:1
Medium parameters used: f = 1950 MHz; σ = 1.47 mho/m; εr = 40.2; ρ = 1000 kg/m3
Phantom section: Flat Section
DASY4 Configuration:
- Probe: ES3DV3 - SN3028; ConvF(4.96, 4.96, 4.96); Calibrated: 8/5/2013
- Sensor-Surface: 4mm (Mechanical Surface Detection)
- Electronics: DAE4 Sn689; Calibrated: 7/20/2013
- Phantom: SAM with TP1360; Type: SAM;
- Measurement SW: DASY4, V4.7 Build 53; Postprocessing SW: SEMCAD, V1.8 Build 172
HS-Worn/Area Scan (81x131x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 0.481 mW/g
HS-Worn/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 9.31 V/m; Power Drift = 0.024 dB
Peak SAR (extrapolated) = 0.692 W/kg
SAR(1 g) = 0.447 mW/g; SAR(10 g) = 0.265 mW/g
Maximum value of SAR (measured) = 0.488 mW/g
0 dB = 0.488mW/g
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 65 / 126
Plot27: Date/Time: 6/14/2014 08:30:22AM
Test Laboratory: SUNWAY COMMUNICATION CO.,LTD.
DUT: Thc4400; Type: Mobile phone
Program Name: Thc4400
Communication System: 802.11; Frequency: 2442 MHz;Duty Cycle: 1:1
Medium parameters used: f = 2442 MHz; σ = 1.82 mho/m; εr = 38.2; ρ = 1000 kg/m3
Phantom section: Flat Section
DASY4 Configuration:
- Probe: ES3DV3 - SN3028; ConvF(4.36, 4.36, 4.36); Calibrated: 8/5/2013
- Sensor-Surface: 4mm (Mechanical Surface Detection)
- Electronics: DAE4 Sn689; Calibrated: 7/20/2013
- Phantom: SAM with TP1360; Type: SAM;
- Measurement SW: DASY4, V4.7 Build 53; Postprocessing SW: SEMCAD, V1.8 Build 172
Side 1/Area Scan (81x131x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 0.189 mW/g
Side 1/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 2.73 V/m; Power Drift = 0.067 dB
Peak SAR (extrapolated) = 0.286 W/kg
SAR(1 g) = 0.165 mW/g; SAR(10 g) = 0.092 mW/g
Maximum value of SAR (measured) = 0.182 mW/g
0 dB = 0.182mW/g
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 66 / 126
Plot28: Date/Time: 6/14/2014 08:50:15PM
Test Laboratory: SUNWAY COMMUNICATION CO.,LTD.
DUT: Thc4400; Type: Mobile phone
Program Name: Thc4400
Communication System: 802.11; Frequency: 2442 MHz;Duty Cycle: 1:1
Medium parameters used: f = 2442 MHz; σ = 1.82 mho/m; εr = 38.2; ρ = 1000 kg/m3
Phantom section: Flat Section
DASY4 Configuration:
- Probe: ES3DV3 - SN3028; ConvF(4.36, 4.36, 4.36); Calibrated: 8/5/2013
- Sensor-Surface: 4mm (Mechanical Surface Detection)
- Electronics: DAE4 Sn689; Calibrated: 7/20/2013
- Phantom: SAM with TP1360; Type: SAM;
- Measurement SW: DASY4, V4.7 Build 53; Postprocessing SW: SEMCAD, V1.8 Build 172
Side 2/Area Scan (81x131x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 0.275 mW/g
Side 2/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 6.03 V/m; Power Drift = 0.070 dB
Peak SAR (extrapolated) = 0.496 W/kg
SAR(1 g) = 0.247 mW/g; SAR(10 g) = 0.132 mW/g
Maximum value of SAR (measured) = 0.265 mW/g
0 dB = 0.265mW/g
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 67 / 126
Plot29: Date/Time: 6/14/2014 09:30:02AM
Test Laboratory: SUNWAY COMMUNICATION CO.,LTD.
DUT: Thc4400; Type: Mobile phone
Program Name: Thc4400
Communication System: 802.11; Frequency: 2442 MHz;Duty Cycle: 1:1
Medium parameters used: f = 2442 MHz; σ = 1.82 mho/m; εr = 38.2; ρ = 1000 kg/m3
Phantom section: Flat Section
DASY4 Configuration:
- Probe: ES3DV3 - SN3028; ConvF(4.36, 4.36, 4.36); Calibrated: 8/5/2013
- Sensor-Surface: 4mm (Mechanical Surface Detection)
- Electronics: DAE4 Sn689; Calibrated: 7/20/2013
- Phantom: SAM with TP1360; Type: SAM;
- Measurement SW: DASY4, V4.7 Build 53; Postprocessing SW: SEMCAD, V1.8 Build 172
Side 3/Area Scan (41x131x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 0.269 mW/g
Side 3/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 8.49 V/m; Power Drift = 0.121 dB
Peak SAR (extrapolated) = 0.477 W/kg
SAR(1 g) = 0.244 mW/g; SAR(10 g) = 0.127 mW/g
Maximum value of SAR (measured) = 0.267 mW/g
0 dB = 0.267mW/g
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 68 / 126
Plot30: Date/Time: 6/14/2014 09:55:12AM
Test Laboratory: SUNWAY COMMUNICATION CO.,LTD.
DUT: Thc4400; Type: Mobile phone
Program Name: Thc4400
Communication System: 802.11; Frequency: 2442 MHz;Duty Cycle: 1:1
Medium parameters used: f = 2442 MHz; σ = 1.82 mho/m; εr = 38.2; ρ = 1000 kg/m3
Phantom section: Flat Section
DASY4 Configuration:
- Probe: ES3DV3 - SN3028; ConvF(4.36, 4.36, 4.36); Calibrated: 8/5/2013
- Sensor-Surface: 4mm (Mechanical Surface Detection)
- Electronics: DAE4 Sn689; Calibrated: 7/20/2013
- Phantom: SAM with TP1360; Type: SAM;
- Measurement SW: DASY4, V4.7 Build 53; Postprocessing SW: SEMCAD, V1.8 Build 172
Side 4/Area Scan (41x131x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 0.123 mW/g
Side 4/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 6.99 V/m; Power Drift = 0.083 dB
Peak SAR (extrapolated) = 0.193 W/kg
SAR(1 g) = 0.112 mW/g; SAR(10 g) = 0.066 mW/g
Maximum value of SAR (measured) = 0.121 mW/g
0 dB = 0.121mW/g
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 69 / 126
Plot31: Date/Time: 6/14/2014 10:20:30AM
Test Laboratory: SUNWAY COMMUNICATION CO.,LTD.
DUT: Thc4400; Type: Mobile phone
Program Name: Thc4400
Communication System: 802.11; Frequency: 2442 MHz;Duty Cycle: 1:1
Medium parameters used: f = 2442 MHz; σ = 1.82 mho/m; εr = 38.2; ρ = 1000 kg/m3
Phantom section: Flat Section
DASY4 Configuration:
- Probe: ES3DV3 - SN3028; ConvF(4.36, 4.36, 4.36); Calibrated: 8/5/2013
- Sensor-Surface: 4mm (Mechanical Surface Detection)
- Electronics: DAE4 Sn689; Calibrated: 7/20/2013
- Phantom: SAM with TP1360; Type: SAM;
- Measurement SW: DASY4, V4.7 Build 53; Postprocessing SW: SEMCAD, V1.8 Build 172
Side 5/Area Scan (41x81x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 0.522 mW/g
Side 5/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 16.3 V/m; Power Drift = 0.108 dB
Peak SAR (extrapolated) = 0.836 W/kg
SAR(1 g) = 0.483 mW/g; SAR(10 g) = 0.274 mW/g
Maximum value of SAR (measured) = 0.530 mW/g
0 dB = 0.530mW/g
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 70 / 126
Plot32: Date/Time: 6/14/2014 10:52:02AM
Test Laboratory: SUNWAY COMMUNICATION CO.,LTD.
DUT: Thc4400; Type: Mobile phone
Program Name: Thc4400
Communication System: 802.11; Frequency: 2442 MHz;Duty Cycle: 1:1
Medium parameters used: f = 2442 MHz; σ = 1.82 mho/m; εr = 38.2; ρ = 1000 kg/m3
Phantom section: Flat Section
DASY4 Configuration:
- Probe: ES3DV3 - SN3028; ConvF(4.36, 4.36, 4.36); Calibrated: 8/5/2013
- Sensor-Surface: 4mm (Mechanical Surface Detection)
- Electronics: DAE4 Sn689; Calibrated: 7/20/2013
- Phantom: SAM with TP1360; Type: SAM;
- Measurement SW: DASY4, V4.7 Build 53; Postprocessing SW: SEMCAD, V1.8 Build 172
Side 6/Area Scan (41x81x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 0.015 mW/g
Side 6/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 2.98 V/m; Power Drift = -0.039 dB
Peak SAR (extrapolated) = 0.026 W/kg
SAR(1 g) = 0.015 mW/g; SAR(10 g) = 0.009 mW/g
Maximum value of SAR (measured) = 0.016 mW/g
0 dB = 0.016mW/g
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 71 / 126
Appendix C. Probe Calibration Data:
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 72 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 73 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 74 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 75 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 76 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 77 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 78 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 79 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 80 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 81 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 82 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 83 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 84 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 85 / 126
Appendix D. DAE Calibration Data:
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 86 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 87 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 88 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 89 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 90 / 126
Appendix E. Dipole Calibration Data:
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 91 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 92 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 93 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 94 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 95 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 96 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 97 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 98 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 99 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 100 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 101 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 102 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 103 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 104 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 105 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 106 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 107 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 108 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 109 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 110 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 111 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 112 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 113 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 114 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 115 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 116 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 117 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 118 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 119 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 120 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 121 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 122 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 123 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 124 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 125 / 126
SHENZHEN SUNWAY COMMUNICATION CO.,LTD
Report NO: TS201406010 Page 126 / 126
*****END OF REPORT*****