CCNA Practice#2
Transcript of CCNA Practice#2
-
CCNA Practice Certification Exam # 2- CCNA Exploration: Accessing the WAN
(Version 4.0)
1. Refer to the exhibit. The exhibit shows simplified protocol data units from different
OSI model layers. Which three statements are true about the PDUs and the
encapsulation process? (Choose three.)
PDU #1 is a frame.
PDU #2 is an application layer PDU
PDU #3 is a segment.
PDU #4 is a transport layer PDU.
The order in which these PDUs are created during the encapsulation process is
3, 4, 1, 2.
The order in which these PDUs are created during the encapsulation process is 2, 1,
4, 3.
2. Which three application layer protocols use TCP? (Choose three.)
SMTP
FTP
SNMP
HTTP
TFTP
DHCP
3. Which two application layer protocols use the UDP protocol? (Choose two.)
Telnet
SNMP
SMTP
SQL
TFTP
4. What are two functions that occur at the Internet layer of the TCP/IP model?
(Choose two.)
establishment of logical connections between source and destination hosts
end-to-end flow control
determination of best paths through the network
definition of the procedures used to interface with the network hardware
packet switching
Layer 5 and Layer 6 OSI model functions
-
5. Refer to the exhibit. All ports on switch A are in the sales VLAN and all ports on
switch B are in the accounting VLAN. How many broadcast domains and how many
collision domains exist in the exhibited network? (Choose two.)
3 collision domains
3 broadcast domains
5 broadcast domains
9 collision domains
10 collision domains
13 collision domains
6. A high-end Catalyst switch that supports both ISL and 802.1Q is to be connected by
a link that will carry all VLAN traffic to a Catalyst 2960 LAN switch. What two
commands are required to configure an interface on the high-end Catalyst switch to
carry traffic from all VLANs to the Catalyst 2960 switch? (Choose two.)
Switch(config-if)# vlan all
Switch(config-if)# switchport access vlan 30
Switch(config-if)# switchport access vlan all
Switch(config-if)# switchport mode trunk
Switch(config-if)# switchport trunk encapsulation dot1q
Switch(config-if)# switchport trunk encapsulation isl
7. Refer to the exhibit. Based on the exhibited configuration and output, what would be
the result of this command:
Sw1# telnet 192.168.1.10
All packets will be dropped.
The Telnet session will succeed.
An error message that says Session terminated will appear.
An error message that says Password required, but none set will appear.
8. Refer to the partial device configuration that is exhibited. For which network
topology is the configuration appropriate?
RtrA(config)# interface fastethernet 0/0
RtrA(config-if)# no shutdown
RtrA(config-if)# interface fastethernet 0/0.18
RtrA(config-subif)# encapsulation dot1q 18
RtrA(config-subif)# ip address 10.1.18.1 255.255.255.0
RtrA(config-subif)# interface fastethernet 0/0.44
-
RtrA(config-subif)# encapsulation dot1q 44
RtrA(config-subif)# ip address 10.1.44.1 255.255.255.0
RtrA(config-subif)# interface fastethernet 0/0.22
RtrA(config-subif)# encapsulation dot1q 22
RtrA(config-subif)# ip address 10.1.22.1 255.255.255.0
9. Refer to the exhibit and the following error message from the SwA switch.
00:22:43: %SPANTREE-7-RECV_1Q_NON_TRUNK: Received 802.1Q BPDU on non
trunk FastEthernet0/1 VLAN1.
00:22:43: %SPANTREE-7-BLOCK_PORT_TYPE: Blocking FastEthernet0/1 on
VLAN0001. Inconsistent port type.
Considering that the link between the two switches is good and the correct type, what
could cause this error message?
The Spanning Tree Protocol has been disabled on one switch.
The Spanning Tree Protocol has been disabled on both switches.
The IEEE 802.1Q trunking port has a speed mismatch on one of the switches.
The SwA port is configured as a trunk port and the SwB port is configured as an
access port.
The SwA port has IEEE 802.1Q trunking enabled and the SwB port has ISL trunking
enabled.
10. A network administrator is configuring a switch when an error message appears.
The configuration commands and error message appear as follows:
Switch(config)# interface fastethernet 0/1
Switch(config-if)# switchport mode trunk
Command rejected: An interface whose trunk encapsulation is Auto can not be
configured to trunk mode.
What is the problem?
The switch port is configured as an access mode port.
The switch port does not support trunking on this port.
-
The encapsulation type must be changed to a compatible protocol before the
port can be placed in trunk mode.
The no switchport trunk encapsulation auto command needs to be applied to the
switch port before trunking can be enabled.
11. Of the protocols that are listed, which one needs to be functioning on a link in order
for VTP to operate?
802.1Q
CDP
RIP
RSTP
12. Refer to the exhibit. RT_1 is configured correctly with IP addresses and passwords
but none of the computers can ping or telnet to RT_1. Which series of commands
would correct the problem?
RT_1(config)# interface fa0/1
RT_1(config-if)# no shutdown
SW_1(config)# interface fa0/24
SW_1(config-if)# switchport mode client
RT_1(config)# interface fa0/1
RT_1(config-if)# encapsulation trunk dot1q 24
SW_1(config)# interface fa0/24
SW_1(config-if)# switchport mode trunk
SW_1(config)# interface fa0/24
SW_1(config-if)# switchport access vlan 1
13. Refer to the exhibit. Which commands are needed to complete the switch
configuration so that SSH can be used to telnet from host A to SW_1? (Choose two.)
SW_1(config)# username david password class
SW_1(config)# line vty 0 15
SW_1(config-line)# login
SW_1(config-line)# password cisco
SW_1(config)# line vty 0 15
SW_1(config-line)# login local
SW_1(config-line)# transport input ssh
-
SW_1(config)# login ssh
SW_1(config)# password class
SW_1(config)# login key rsa
SW_1(config)# password cisco
SW_1(config)# password encrypted cisco
14. What three factors contribute to congestion on an Ethernet LAN? (Choose three.)
improper placement of enterprise level servers
addition of hosts to a physical segment
replacement of hubs with workgroup switches
increasing use of bandwidth intensive network applications
creation of new collision domains without first adding network hosts
migration to full-duplex Ethernet within the LAN
15. Refer to the exhibit. What protocol should be configured on SW-A Port 0/1 if it is to
sendtraffic from multiple VLANs to switch SW-B?
Spanning Tree
RIP v2
IEEE 802.1Q
ARP
Rapid Spanning Tree
16. Which three STP states were replaced with the RSTP discarding state? (Choose
three.)
listening
learning
blocking
disabled
forwarding
17. Refer to the exhibit. What is the role of the SW3 switch?
designated switch
edge switch
root bridge
enabled bridge
local bridge
-
18. Refer to the exhibit. A switch can be configured for three different forwarding
modes based on how much of a frame is received before the forwarding process
begins. Each of the numbered arrows in the accompanying graphic signifies the point
in a frame where a particular forwarding mode will begin. Which group of labels
reflects the sequence of forwarding modes signified by the numbered arrows?
1) fast forward
2) fragment free
3) store-and-forward
1) store-and-forward
2) fragment free
3) fast forward
1) fragment free
2) fast forward
3) store-and-forward
1) fast forward
2) store-and-forward
3) fragment free
19. What eliminates switching loops?
hold-down timers
poison reverse
spanning tree protocol
time to live
VTP
20.
21. Refer to the exhibit. Using the most efficient IP addressing scheme and VLSM,
which address can be configured on one of the serial interfaces?
192.168.16.63/27
192.168.16.158/27
192.168.16.192/27
192.168.16.113/30
192.168.16.145/30
192.168.16.193/30
-
22. Consider this router output:
Router# confug
Translating confugdomain server (255.255.255.255)
Translating confugdomain server (255.255.255.255)
(255.255.255.255)% Unknown command or computer name, or unable to find
computer address
What command could help with this situation?
ip dhcp server
no ip domain-lookup
no logging synchronous
no show ip nat translations
23. Refer to the exhibit. With VLSM, which bit mask should be used to most efficiently
provide for the number of host addresses that are required on router B?
/26
/27
/28
/29
/30
24. What are the three ranges of IP addresses that are reserved for internal private
use? (Choose three.)
10.0.0.0/8
64.100.0.0/14
127.16.0.0/12
172.16.0.0/12
192.31.7.0/24
192.168.0.0/16
25. Refer to the exhibit. The network administrator is unable to access the TFTP
server attached to the Memphis router. What are two causes of this problem? (Choose
two.)
The default gateway configured on the network administrators workstation is not a
valid host address.
The default gateway configured on the TFTP server in incorrect.
-
The IP address of the TFTP server is a subnetwork address.
The IP address of the S0/0/0 interface of the Heliopolis router is a broadcast
address.
The IP addresses for the Memphis S0/0/1 interface and the Heliopolis S0/0/0
interface are not in the same subnet.
26. The ISP of the XYZ Company is moving to IPv6 but XYZ wants to continue to use
only IPv4 for another year. Which IPv4-to-IPv6 transition method would allow the
company to continue using only IPv4 addresses?
dual stack
6to4 tunnel
manual tunneling
NAT-PT
27. Given the IP address and subnet mask of 172.16.134.56 255.255.255.224, on
which subnetwork does this address reside?
172.16.0.0
172.16.134.0
172.16.134.32
172.16.134.48
172.16.134.47
172.16.134.63
28. What is associated with link-state routing protocols?
low processor overhead
poison reverse
routing loops
split horizon
shortest-path first calculations
29. Refer to the exhibit. Which sequence of commands should be used to configure
router A for OSPF?
router ospf 1
network 192.168.10.0
router ospf 1
network 192.168.10.64 0.0.0.63 area 0
network 192.168.10.192 0.0.0.3 area 0
router ospf 1
-
network 192.168.10.64 255.255.255.192
network 192.168.10.192 255.255.255.252
router ospf 1
network 192.168.10.0 area 0
30. What is one reason to use the ip ospf priority command when the OSPF routing
protocol is in use?
to activate the OSPF neighboring process
to influence the DR/BDR election process
to provide a backdoor for connectivity during the convergence process
to streamline and speed up the convergence process
31. The output of the show ip interface brief command indicates that Serial0 is up but
the line protocol is down. What are two possible causes for the line protocol being in
the down state? (Choose two.)
The clock rate is not set on the DTE.
An incorrect default gateway is set on the router.
A network is missing from the routing protocol configuration.
The encapsulation on the Serial0 interface is incorrect.
Keepalives are not being sent by the remote device.
32. Which router command will verify that the router has a path to a destination
network?
Router# show ip interfaces brief
Router# show ip route
Router# show cdp neighbors
Router# show running-config
Router# show protocols
33. Refer to the exhibit. When troubleshooting a network, it is important to interpret the
output of various router commands. On the basis of the exhibit, which three statements
are true? (Choose three.)
The missing information for Blank 1 is the command show ip route.
The missing information for Blank 1 is the command debug ip route.
The missing information for Blank 2 is the number 100.
The missing information for Blank 2 is the number 120.
The missing information for Blank 3 is the letter R.
The missing information for Blank 3 is the letter C.
-
34. Refer to the exhibit. From the command prompt on the host, the command telnet
192.168.1.10 is typed. The response that is given is this:
Trying 192.168.1.10.Open
Password required, but none set
What is the most likely problem?
The router has been configured as a firewall.
The Telnet server process must be activated on the router.
The switch has not been configured to pass Telnet traffic.
The enable secret command has not been entered on RtrA.
The password command has not been entered in line configuration mode on
RtrA.
The password and login commands need to be configured on the console port of
RtrA.
35. Refer to the exhibit. If router B is to be configured for EIGRP AS 100, which
configuration must be entered?
B(config-router)# network 192.168.10.4 0.0.0.3
B(config-router)# network 192.168.10.8 0.0.0.3
B(config-router)# network 192.168.10.4 0.0.0.3
B(config-router)# network 192.168.10.8 0.0.0.3
B(config-router)#network 192.168.10.128 0.0.0.63
B(config-router)# network 192.168.10.4 0.0.0.3 area 0
B(config-router)# network 192.168.10.8 0.0.0.3 area 0
B(config-router)#network 192.168.10.128 0.0.0.63 area 0
B(config-router)# network 192.168.10.4 0.0.0.3 as 100
B(config-router)# network 192.168.10.8 0.0.0.3 as 100
B(config-router)#network 192.168.10.128 0.0.0.63 as 100
B(config-router)# network 192.168.10.4 0.0.0.3
B(config-router)# network 192.168.10.8 0.0.0.3
B(config-router)# network 192.168.10.64 0.0.0.63
B(config-router)# network 192.168.10.128 0.0.0.63
B(config-router)# network 192.168.10.192 0.0.0.63
B(config-router)# network 192.168.10.4 0.0.0.3 as 100
-
B(config-router)# network 192.168.10.8 0.0.0.3 as 100
B(config-router)# network 192.168.10.64 0.0.0.63 as 100
B(config-router)# network 192.168.10.128 0.0.0.63 as 100
B(config-router)# network 192.168.10.192 0.0.0.63 as 100
B(config-router)# network 192.168.10.4 0.0.0.3 area 100
B(config-router)# network 192.168.10.8 0.0.0.3 area 100
B(config-router)# network 192.168.10.64 0.0.0.63 area 100
B(config-router)# network 192.168.10.128 0.0.0.63 area 100
B(config-router)# network 192.168.10.192 0.0.0.63 area 100
36. After several configuration changes are made to a router, the copy running-
configuration startup-configuration command is issued. Where will the changes be
stored?
flash
ROM
NVRAM
RAM
the configuration register
a TFTP server
37. Refer to the exhibit. Two routers have been configured to use EIGRP. Packets are
not being forwarded between the two routers. What could be the problem?
EIGRP does not support VLSM.
The routers were not configured to monitor neighbor adjacency changes.
The default bandwidth was used on the routers.
An incorrect IP address was configured on a router interface.
38. What are two features of a link-state routing protocol? (Choose two.)
Routers send periodic updates only to neighboring routers.
Routers send triggered updates in response to a change.
Routers create a topology of the network by using information from other
routers.
The database information for each router is obtained from the same source.
Paths are chosen based on the lowest number of hops to the designated router.
39. Refer to the exhibit. Routers A and B have EIGRP configured and automatic
summarization has been disabled on both routers. Which router command is used to
-
summarize the attached routes, and to which interface is this command applied?
(Choose two.)
ip summary-address eigrp 1 192.168.10.64 255.255.255.192
ip area-range eigrp 1 192.168.10.80 255.255.255.224
summary-address 192.168.10.80 0.0.0.31
ip summary-address eigrp 1 192.168.10.64 0.0.0.63
serial interface on router A
serial interface on router B
40. A router has learned about network 192.168.168.0 through static and dynamic
routing processes. Which route will appear in the routing table for this network if the
router has learned multiple routes?
D 192.168.168.0/24 [90/2195456] via 192.168.200.1, 00:00:09, FastEthernet0/0
O 192.168.168.0/24 [110/1012] via 192.168.200.1, 00:00:22, FastEthernet0/0
R 192.168.168.0/24 [120/1] via 192.168.200.1, 00:00:17, FastEthernet0/0
S 192.168.168.0/24 [1/0] via 192.168.200.1
41. Which sequence of commands is used to configure a loopback address on a
router?
Router1(config)# interface loopback 1
Router1(config-if)# ip address 192.168.1.1
Router1(config)# interface serial 0/0
Router1(config-if)# loopback 1
Router1(config-if)# ip address 192.168.1.1
Router1(config)# interface serial 0/0
Router1(config-if)# loopback 1
Router1(config-if)# ip address 192.168.1.1 255.255.255.0
Router1(config)# interface loopback 1
Router1(config-if)# ip address 192.168.1.1 255.255.255.255
42.
43. Which encryption standard would most likely be used in an 802.11 standards-
based wireless network environment?
ACDP, which has more bits that are used for encryption than CDP has
WPA2, which can use the more advanced AES for encryption
VTP, which is compatible with all 802.11-type wireless networks
RSA, which has a different algorithm than any of the older standards
-
802.1X EAP, which is the most powerful type of encryption used for both wired and
wireless networks
44.
45.
46. Which two commands can be used to verify the content and placement of access
control lists? (Choose two.)
show ip route
show processes
show running-config
show cdp neighbor
show access-lists
47. Which two keywords can be used in an access control list to replace a wildcard
mask or address and wildcard mask pair? (Choose two.)
most
host
all
any
some
gt
48. Refer to the exhibit. NAT with overload is configured on router R1 and uses the
NAT pool of addresses 209.165.201.9 through 209.165.201.10. What type of route
would the ISP need in order for communication to occur between hosts in Company
ABC and the Internet?
Because the ISP has knowledge of the directly connected 200.0.0.1 network, no route
is needed.
A static route from the ISP is needed that uses the network number 172.16.0.0 and the
mask 255.255.0.0.
A default route from the ISP is needed that uses either the exit interface of S0/0/0 or
the 200.0.0.1 IP address.
A default route from the ISP is needed that uses either the exit interface of S0/0/1 or
the 200.0.0.2 IP address.
A static route from the ISP is needed that uses the network number
-
209.165.201.8and the mask 255.255.255.252.
49. What is the effect of the access control list wildcard mask 0.0.0.15? (Choose two.)
The first 28 bits of a supplied IP address will be ignored.
The last four bits of a supplied IP address will be ignored.
The first 32 bits of a supplied IP address will be matched.
The first 28 bits of a supplied IP address will be matched.
The last five bits of a supplied IP address will be ignored.
The last four bits of a supplied IP address will be matched.
50. Which three values or sets of values are included when creating an extended
access control list statement? (Choose three.)
access list number between 1 and 99
access list number between 100 and 199
default gateway address and wildcard mask
destination address and wildcard mask
source address and wildcard mask
source subnet mask and wildcard mask
destination subnet mask and wildcard mask
51. Refer to the exhibit. Which statement describes the status of the PPP connection?
Only the link-establishment phase completed successfully.
Only the network-layer phase completed successfully.
Neither the link-establishment phase nor the network-layer phase completed
successfully.
Both the link-establishment and network-layer phase completed successfully.
52. Which three statements are true regarding the Frame Relay LMI? (Choose three.)
The LMI provides a virtual circuit (VC) status mechanism.
The LMI type must always be manually configured.
The available LMI types are CHAP and PAP.
The LMI types supported by Cisco routers are CISCO and IETF.
The LMI type configured on the router must match the one used on the Frame
Relay switch.
The LMI uses reserved DLCIs to exchange messages between the DTE and DCE.
53. A network administrator is evaluating authentication protocols for a PPP link.
Which three factors might lead to the selection of CHAP over PAP as the
authentication protocol? (Choose three.)
-
establishes identities with a two-way handshake
uses a three-way authentication periodically during the session to reconfirm
identities
control by the remote host of the frequency and timing of login events
transmits login information in encrypted format
uses an unpredictable variable challenge value to prevent playback attacks
makes authorized network administrator intervention a requirement to establish each
session
54. Which three statements are true about PPP? (Choose three.)
PPP can use synchronous and asynchronous circuits.
PPP can only be used between two Cisco devices.
PPP carries packets from several network layer protocols in LCPs.
PPP uses LCPs to establish, configure, and test the data link connection.
PPP uses LCPs to agree on format options such as authentication,
compression, and error detection.
Certificacin CCNA Practice Exam # 2 - CCNA Exploration : Acceso a la WAN (versin 4.0 )
1 . Consulte la presentacin . La exposicin muestra las unidades de datos de protocolo simplificado de las
diferentes capas del modelo OSI. Qu tres afirmaciones son ciertas acerca de las PDU y el proceso de
encapsulacin ? ( Elija tres opciones).
PDU # 1 es un marco.
PDU # 2 es una PDU de capa de aplicacin
PDU # 3 es un segmento .
PDU # 4 es una PDU de capa de transporte .
El orden en el que estas PDU se crean durante el proceso de encapsulacin es 3 , 4 , 1 , 2 .
El orden en el que estas PDU se crean durante el proceso de encapsulacin es 2 , 1 , 4 , 3 .
2 . Protocolos de capa Qu tres aplicaciones utilizan TCP ? ( Elija tres opciones).
SMTP
FTP
SNMP
HTTP
TFTP
DHCP
3 . Qu dos protocolos de capa de aplicacin utilizan el protocolo UDP ? (Elija dos opciones ).
Telnet
SNMP
SMTP
SQL
TFTP
4 . Cules son dos funciones que se producen en la capa de Internet del modelo TCP / IP? (Elija dos
opciones ).
establecimiento de conexiones lgicas entre origen y destino hosts
control de flujo de extremo a extremo
determinar las mejores rutas a travs de la red
definicin de los procedimientos utilizados para la interfaz con el hardware de red
conmutacin de paquetes
Funciones de la capa 5 y 6 Capa modelo OSI
-
5 . Consulte la presentacin . Todos los puertos de switch A estn en la VLAN de ventas y todos los puertos
del conmutador B estn en la VLAN de contabilidad. Cuntos dominios de broadcast y cuntos dominios de
colisin existen en la red exhibida ? (Elija dos opciones ).
3 dominios de colisin
3 dominios de difusin
5 dominios de difusin
9 dominios de colisin
10 dominios de colisin
13 dominios de colisin
6 . Un switch Catalyst de alta gama que es compatible tanto con ISL y 802.1Q va a ser conectado por un
enlace que llevar a todo el trfico de VLAN a un conmutador LAN Catalyst 2960 . Qu dos comandos se
requieren para configurar una interfaz en el switch Catalyst de gama alta para llevar el trfico de todas las
VLAN al switch Catalyst 2960 ? (Elija dos opciones ).
Switch ( config- if) # vlan todo
Switch (config -if) # switchport vlan acceso 30
Switch (config -if) # switchport vlan acceso todos
Switch (config -if) # switchport modo de tronco
Switch ( config- if) # switchport tronco encapsulacin dot1q
Switch ( config- if) # switchport tronco encapsulacin isl
7 . Consulte la presentacin . Sobre la base de la configuracin y la produccin exhibida , cul sera el
resultado de este comando:
Sw1 # telnet 192.168.1.10
Ser dado de baja todos los paquetes .
La sesin de Telnet tendr xito.
Un mensaje de error que dice " Sesin terminada " aparecer .
Un mensaje de error que dice " Contrasea requerida , pero ninguno set" aparecer .
8 . Consulte la configuracin del dispositivo parcial que se exhibe . Para que la red de topologa es apropiada
la configuracin?
RtrA (config ) # interface FastEthernet 0 / 0
RtrA (config -if) # no shutdown
RtrA (config -if) # interface FastEthernet 0/0.18
RtrA (config- subif ) dot1q # encapsulacin 18
RtrA (config- subif ) # ip address 255.255.255.0 10.1.18.1
RtrA (config- subif ) # interface FastEthernet 0/0.44
RtrA (config- subif ) dot1q # encapsulacin 44
RtrA (config- subif ) # ip address 255.255.255.0 10.1.44.1
RtrA (config- subif ) # interface FastEthernet 0/0.22
RtrA (config- subif ) dot1q # encapsulacin 22
RtrA (config- subif ) # ip address 255.255.255.0 10.1.22.1
9 . Consulte la presentacin y el mensaje de error del interruptor SwA .
00:22:43 :% spantree - 7 - RECV_1Q_NON_TRUNK : Recibido 802.1Q BPDU en la no tronco
FastEthernet0 / 1 VLAN1 .
00:22:43 :% spantree - 7 - BLOCK_PORT_TYPE : Bloqueo FastEthernet0 / 1 en VLAN0001 . Tipo de
puerto incoherente .
Teniendo en cuenta que el vnculo entre los dos interruptores es buena y el tipo correcto , lo que podra
provocar este mensaje de error?
El Protocolo Spanning Tree se ha deshabilitado en un interruptor .
El Protocolo Spanning Tree se ha desactivado en ambos interruptores .
El puerto de enlace troncal IEEE 802.1Q tiene un desajuste de velocidad en uno de los interruptores .
-
El puerto SwA est configurado como un puerto de enlace troncal y el puerto SWB se configura como un
puerto de acceso .
El puerto SwA ha permitido IEEE 802.1Q trunking y el puerto SWB ha permitido ISL Trunking .
10 . Un administrador de red es la configuracin de un interruptor cuando aparezca un mensaje de error . Los
comandos de configuracin y mensajes de error aparecen como sigue:
Switch ( config) # interface FastEthernet 0 / 1
Switch (config -if) # switchport modo de tronco
Comando rechazado : Una interfaz cuya encapsulacin tronco es " Auto" no se puede configurar en modo de
"tronco" .
Cul es el problema?
El puerto de conmutacin est configurado como un puerto de modo de acceso .
El puerto del conmutador no soporta trunking en este puerto.
El tipo de encapsulacin debe ser cambiado a un protocolo compatible antes de que el puerto puede ser
colocado en el modo de tronco .
Los no necesita el comando auto switchport tronco de encapsulacin que se aplicarn al puerto del switch
antes de trunking se pueden habilitar .
11 . De los protocolos que se enumeran , que uno tiene que estar funcionando en un enlace para que VTP para
operar ?
802.1Q
CDP
RIP
RSTP
12 . Consulte la presentacin . RT_1 est configurado correctamente con las direcciones IP y las contraseas ,
pero ninguno de los equipos puede hacer ping o telnet para RT_1 . Qu serie de comandos sera corregir el
problema?
RT_1 (config ) # interface Fa0 / 1
RT_1 (config -if) # no shutdown
SW_1 (config ) # interface Fa0/24
SW_1 (config -if) # switchport modo cliente
RT_1 (config ) # interface Fa0 / 1
RT_1 (config -if) # tronco encapsulacin dot1q 24
SW_1 (config ) # interface Fa0/24
SW_1 (config -if) # switchport mode trunk
SW_1 (config ) # interface Fa0/24
SW_1 (config -if) # switchport vlan acceso 1
13 . Consulte la presentacin . Qu comandos son necesarios para completar la configuracin del switch para
que SSH se puede utilizar para hacer telnet desde el host A a SW_1 ? (Elija dos opciones ).
SW_1 ( config) # nombre de usuario de clase david contrasea
SW_1 (config ) # line vty 0 15
SW_1 (config -line) # login
SW_1 (config -line) # password cisco
SW_1 (config ) # line vty 0 15
SW_1 (config -line) # login locales
SW_1 (config -line) # ssh entrada de transporte
SW_1 (config ) # login ssh
SW_1 (config ) # class contrasea
SW_1 (config ) # login clave RSA
SW_1 ( config) # password cisco
Cisco cifrada SW_1 ( config) # password
14 . Qu tres factores contribuyen a la congestin en una LAN Ethernet ? ( Elija tres opciones).
colocacin incorrecta de los servidores de nivel empresarial
Adems de los ejrcitos a un segmento fsico
el reemplazo de los centros con los interruptores de grupo de trabajo
aumento del uso de aplicaciones de ancho de banda de red intensivos
-
creacin de nuevos dominios de colisin sin agregar primero hosts de la red
migracin a full- duplex Ethernet dentro de la LAN
15 . Consulte la presentacin . Qu protocolo debe configurarse en SW -A puerto 0 / 1 si se va a enviar el
trfico de varias VLAN para cambiar SW- B?
spanning Tree
RIP v2
IEEE 802.1Q
ARP
Rapid Spanning Tree
16 . Qu tres estados STP fueron sustituidos por el estado descartando RSTP ? ( Elija tres opciones).
escucha
aprendizaje
bloqueo
discapacitado
expedicin
17 . Consulte la presentacin . Cul es el papel del interruptor SW3 ?
switch designado
conmutador de acceso
puente raz
puente habilitado
puente locales
18 . Consulte la presentacin . Un interruptor puede estar configurado para tres modos de reenvo diferentes
sobre la base de la cantidad de una trama se recibe antes de que comience el proceso de reenvo . Cada una de
las flechas numeradas en el grfico adjunto significa el punto en un marco donde se iniciar un modo de
transmisin en particular. Qu grupo de etiquetas refleja la secuencia de modos de reenvo significadas por
las flechas numeradas ?
1 ) el avance rpido
2 ) libre de fragmentos
3 ) store- and-forward
1 ) store- and-forward
2 ) libre de fragmentos
3 ) el avance rpido
1 ) libre de fragmentos
2 ) el avance rpido
3 ) store- and-forward
1 ) el avance rpido
2 ) store- and-forward
3 ) libre de fragmentos
19 . Lo que elimina bucles de conmutacin ?
temporizadores de espera
inalcanzables
Protocolo de rbol
tiempo para vivir
VTP
20 .
21 . Consulte la presentacin . Utilizando el esquema ms eficiente de direccionamiento IP y VLSM , cuya
direccin se puede configurar en una de las interfaces en serie ?
192.168.16.63/27
192.168.16.158/27
192.168.16.192/27
192.168.16.113/30
192.168.16.145/30
-
192.168.16.193/30
22 . Considere esta salida del router:
Router # confug
La traduccin de " confug " ... servidor de dominio ( 255.255.255.255)
La traduccin de " confug " ... servidor de dominio ( 255.255.255.255)
( 255.255.255.255) % comando desconocido o nombre de equipo, o no puede encontrar la direccin de la
computadora
Qu comando podra ayudar con esta situacin?
servidor dhcp ip
no ip domain-lookup
no sincrnica tala
no show ip nat translations
23 . Consulte la presentacin . Con VLSM , que poco mscara debe ser utilizado para proporcionar de manera
ms eficiente para el nmero de direcciones host que se requieren en el router B?
/ 26
/ 27
/ 28
/ 29
/ 30
24 . Cules son los tres rangos de direcciones IP que estn reservadas para uso privado interno ? ( Elija tres
opciones).
10.0.0.0 / 8
64.100.0.0/14
127.16.0.0/12
172.16.0.0/12
192.31.7.0/24
192.168.0.0/16
25 . Consulte la presentacin . El administrador de la red no puede acceder al servidor TFTP conectado al
router Memphis. Cules son dos causas de este problema ? (Elija dos opciones ).
La puerta de enlace predeterminada configurada en el equipo administrador de la red no es una direccin
vlida de host .
La puerta de enlace predeterminada configurada en el servidor TFTP en correctos .
La direccin IP del servidor TFTP es una direccin de subred.
La direccin IP de la interfaz S0/0/0 del router Helipolis es una direccin de difusin .
Las direcciones IP de la interfaz de Memphis y la interfaz S0/0/1 S0/0/0 Helipolis no estn en la misma
subred.
26 . El ISP de la Compaa XYZ se est moviendo hacia el IPv6 pero XYZ quiere seguir utilizando slo IPv4
por otro ao. Qu mtodo de transicin de IPv4 a IPv6 permitira a la compaa continuar utilizando
nicamente las direcciones IPv4 ?
doble pila
tnel 6to4
tnel manual de
NAT -PT
27 . Dada la direccin IP y la mscara de subred de 172.16.134.56 255.255.255.224 , en el que reside la
subred esta direccin?
172.16.0.0
172.16.134.0
172.16.134.32
172.16.134.48
172.16.134.47
172.16.134.63
28 . Lo que est asociado con los protocolos de enrutamiento de estado de enlace ?
baja sobrecarga del procesador
inalcanzables
-
bucles de enrutamiento
horizonte dividido
camino ms corto primero clculos
29 . Consulte la presentacin . Qu secuencia de comandos se debe utilizar para configurar el router A para
OSPF ?
router ospf 1
red 192.168.10.0
router ospf 1
red 192.168.10.64 rea 0.0.0.63 0
red 192.168.10.192 0.0.0.3 area 0
router ospf 1
red 192.168.10.64 255.255.255.192
red 192.168.10.192 255.255.255.252
router ospf 1
red 192.168.10.0 zona 0
30 . Cul es una razn para usar el comando ip ospf priority cuando el protocolo de enrutamiento OSPF est
en uso?
para activar el proceso de OSPF vecino
para influir en el proceso de eleccin de DR / BDR
para proporcionar una puerta trasera para la conectividad durante el proceso de convergencia
para simplificar y acelerar el proceso de convergencia
31 . La salida de la breve comando show ip interface Serial0 indica que corresponde , pero el protocolo de
lnea est abajo. Cules son dos posibles causas para el protocolo de lnea est en el estado abajo? (Elija dos
opciones ).
La velocidad del reloj no se encuentra en el DTE.
Una puerta de enlace predeterminada incorrecta se configura en el router.
Una red no aparece en la configuracin del protocolo de enrutamiento.
La encapsulacin de la interfaz Serial0 es incorrecta.
Keepalives no estn siendo enviados por el dispositivo remoto .
32 . Qu comando router ser verificar que el router tiene una ruta de acceso a una red de destino ?
Router # show interfaces IP breve
Ruta Router # show ip
Vecinos Router # show cdp
Router # show running -config
Protocolos Router # show
33 . Consulte la presentacin . Al solucionar problemas de una red, es importante interpretar la salida de
varios comandos del router . Sobre la base de la exposicin, que tres afirmaciones son ciertas ? ( Elija tres
opciones).
La informacin que faltaba para Blank 1 es el comando show ip route .
La informacin que faltaba para Blank 1 es la ruta de comando debug ip .
La informacin que faltaba para Blank 2 es el nmero 100 .
La informacin que faltaba para Blank 2 es el nmero 120 .
La informacin que faltaba para Blank 3 es la letra R.
La informacin que faltaba para Blank 3 es la letra C.
34 . Consulte la presentacin . Desde el smbolo del sistema del anfitrin, el telnet 192.168.1.10 comando se
escribe . La respuesta que se da es la siguiente:
Tratando 192.168.1.10 .... Abrir
Contrasea requerida , pero ninguno establece
Cul es el problema ms probable ?
El router se ha configurado como un servidor de seguridad .
El proceso del servidor Telnet debe estar activado en el router.
El interruptor no se ha configurado para pasar el trfico de Telnet.
El comando enable secret no est actualmente disponible en RtrA .
-
El comando de la contrasea no se ha introducido en el modo de configuracin de lnea en RtrA .
Las contraseas de inicio de sesin y los comandos se deben configurar en el puerto de la consola de RtrA .
35 . Consulte la presentacin . Si el router B se va a configurar para EIGRP AS 100 , qu configuracin se
debe introducir ?
B (config -router) # network 192.168.10.4 0.0.0.3
B (config -router) # network 192.168.10.8 0.0.0.3
B (config -router) # network 192.168.10.4 0.0.0.3
B (config -router) # network 192.168.10.8 0.0.0.3
B (config -router) # network 192.168.10.128 0.0.0.63
B (config -router) # network 192.168.10.4 0.0.0.3 area 0
B (config -router) # network 192.168.10.8 0.0.0.3 area 0
B (config -router) # network 192.168.10.128 0.0.0.63 zona 0
B (config -router) # network 192.168.10.4 0.0.0.3 como 100
B (config -router) # network 192.168.10.8 0.0.0.3 como 100
B (config -router) # network 192.168.10.128 0.0.0.63 como 100
B (config -router) # network 192.168.10.4 0.0.0.3
B (config -router) # network 192.168.10.8 0.0.0.3
B (config -router) # network 192.168.10.64 0.0.0.63
B (config -router) # network 192.168.10.128 0.0.0.63
B (config -router) # network 192.168.10.192 0.0.0.63
B (config -router) # network 192.168.10.4 0.0.0.3 como 100
B (config -router) # network 192.168.10.8 0.0.0.3 como 100
B (config -router) # network 192.168.10.64 0.0.0.63 como 100
B (config -router) # network 192.168.10.128 0.0.0.63 como 100
B (config -router) # network 192.168.10.192 0.0.0.63 como 100
B (config -router) # network 192.168.10.4 0.0.0.3 area 100
B (config -router) # network 192.168.10.8 0.0.0.3 area 100
B (config -router) # network 192.168.10.64 0.0.0.63 rea 100
B (config -router) # network 192.168.10.128 0.0.0.63 rea 100
B (config -router) # network 192.168.10.192 0.0.0.63 rea 100
36 . Despus de realizar varios cambios en la configuracin de un router, se emite el comando de
configuracin de inicio de rodaje de configuracin de copia. Dnde se guardan los cambios?
flash
ROM
NVRAM
RAM
el registro de configuracin
un servidor TFTP
37 . Consulte la presentacin . Dos routers se han configurado para utilizar EIGRP. Los paquetes no se
reenvan entre los dos routers. Cul puede ser el problema?
EIGRP no soporta VLSM .
Los routers no estaban configurados para monitorizar los cambios de adyacencia de vecinos .
El ancho de banda por defecto se utiliza en los routers .
Una direccin IP incorrecta se ha configurado en una interfaz de router.
38 . Cules son dos aspectos de un protocolo de enrutamiento de estado de enlace ? (Elija dos opciones ).
Los routers envan actualizaciones peridicas slo a los routers vecinos.
Los routers envan actualizaciones desencadenadas en respuesta a un cambio.
Los routers crean una topologa de la red mediante el uso de la informacin de otros routers.
La informacin de base de datos para cada router se obtiene de la misma fuente .
Caminos se eligen basndose en el menor nmero de saltos al router designado.
39 . Consulte la presentacin . Routers A y B han EIGRP configurado y el resumen automtico se ha
desactivado en ambos routers . Qu comando router se utiliza para resumir las rutas conectados, y al que la
interfaz se aplica este comando ? (Elija dos opciones ).
-
ip - resumen direccin eigrp 1 192.168.10.64 255.255.255.192
ip rea de alcance eigrp 1 192.168.10.80 255.255.255.224
Resumen - direccin 192.168.10.80 0.0.0.31
ip - resumen direccin eigrp 1 192.168.10.64 0.0.0.63
interfaz serial en el router A
interfaz serial en el router B
40 . Un router ha aprendido acerca de la red 192.168.168.0 a travs de los procesos de enrutamiento esttico y
dinmico. Qu ruta aparecer en la tabla de enrutamiento para esta red si el router ha aprendido varias rutas ?
D 192.168.168.0/24 [ 90/2195456 ] via 192.168.200.1 , 00:00:09 , FastEthernet0 / 0
O 192.168.168.0/24 [ 110/1012 ] via 192.168.200.1 , 00:00:22 , FastEthernet0 / 0
R 192.168.168.0/24 [ 120/1 ] via 192.168.200.1 , 00:00:17, FastEthernet0 / 0
S 192.168.168.0/24 [ 1 / 0 ] via 192.168.200.1
41 . Qu secuencia de comandos se utiliza para configurar una direccin de loopback en un router ?
Router1 (config ) # interface loopback 1
Router1 (config -if) # ip 192.168.1.1 Direccin
Router1 (config ) # interface serial 0 / 0
Router1 (config -if) # loopback 1
Router1 (config -if) # ip 192.168.1.1 Direccin
Router1 (config ) # interface serial 0 / 0
Router1 (config -if) # loopback 1
Router1 (config -if) # ip address 192.168.1.1 255.255.255.0
Router1 (config ) # interface loopback 1
Router1 (config -if) # ip address 192.168.1.1 255.255.255.255
42 .
43 . Qu estndar de cifrado lo ms probable es ser utilizado en un entorno de red inalmbrica basada en
estndares 802.11 ?
ACDP , que tiene ms bits que se utilizan para el cifrado de CDP tiene
WPA2 , que puede utilizar el AES ms avanzada para el cifrado
VTP , que es compatible con todas las redes inalmbricas 802.11 de tipo
RSA , que tiene un algoritmo diferente de cualquiera de las normas ms antiguas
802.1X EAP , que es el tipo ms poderoso de cifrado que se utiliza tanto para redes cableadas e inalmbricas
44 .
45 .
46 . Qu dos comandos se puede utilizar para verificar el contenido y la ubicacin de las listas de control de
acceso ? (Elija dos opciones ).
mostrar la ruta del IP
procesos de demostracin
show running- config
mostrar vecino cdp
mostrar listas de acceso
47 . Qu dos palabras clave se puede utilizar en una lista de control de acceso para sustituir una mascara o la
direccin y el par de mscara wildcard ? (Elija dos opciones ).
ms
anfitrin
todo
cualquier
algunos
gt
48 . Consulte la presentacin . NAT con sobrecarga est configurado en el router R1 y utiliza el pool de NAT
de direcciones 209.165.201.9 a travs 209.165.201.10 . Qu tipo de ruta necesitara el ISP a fin de que la
comunicacin se produzca entre los hosts en la Compaa ABC y el Internet ?
Debido a que el ISP tiene conocimiento de la red 200.0.0.1 conectado directamente , no se necesita ninguna
ruta.
Se necesita una ruta esttica desde el ISP que utiliza el nmero de red 172.16.0.0 y la mscara 255.255.0.0 .
-
Se necesita una ruta por defecto desde el ISP que utiliza la interfaz de salida de S0/0/0 o la direccin IP
200.0.0.1 .
Se necesita una ruta por defecto desde el ISP que utiliza la interfaz de salida de S0/0/1 o la direccin IP
200.0.0.2 .
Se necesita una ruta esttica desde el ISP que utiliza el nmero 209.165.201.8 red y la mscara de
255.255.255.252 .
49 . Cul es el efecto de la lista de control de acceso mscara wildcard 0.0.0.15 ? (Elija dos opciones ).
Se ignorarn los primeros 28 bits de una direccin IP proporcionada .
Se ignorarn los ltimos cuatro bits de una direccin IP proporcionada .
Se compararn los primeros 32 bits de una direccin IP proporcionada .
Se compararn los primeros 28 bits de una direccin IP proporcionada .
Se ignorarn los ltimos cinco bits de una direccin IP proporcionada .
Se compararn los ltimos cuatro bits de una direccin IP proporcionada .
50 . Qu se incluyen tres valores o conjuntos de valores al crear una sentencia de la lista de control de acceso
extendido? ( Elija tres opciones).
nmero de lista de acceso de entre 1 y 99
nmero de lista de acceso de entre 100 y 199
direccin de puerta de enlace predeterminada y la mscara wildcard
direccin de destino y la mscara wildcard
direccin de origen y la mscara wildcard
mscara de subred de origen y la mscara wildcard
mscara de subred de destino y mscara wildcard
51 . Consulte la presentacin . Qu enunciado describe el estado de la conexin PPP?
Slo la fase de establecimiento de enlace ha completado correctamente.
Slo la fase de capa de red ha finalizado satisfactoriamente.
Ni la fase de establecimiento de enlace ni la fase de capa de red completada con xito .
Tanto la fase de acoplamiento - establecimiento y la capa de red ha finalizado satisfactoriamente.
52 . Qu tres afirmaciones son ciertas con respecto a la Frame Relay LMI ? ( Elija tres opciones).
La LMI proporciona un circuito virtual ( VC ) mecanismo de estado.
El tipo de LMI siempre se debe configurar manualmente.
Los tipos disponibles son LMI CHAP y PAP .
Los tipos de LMI soportados por los routers de Cisco son CISCO e IETF .
El tipo de LMI configurado en el router debe coincidir con el utilizado en el switch Frame Relay .
La LMI utiliza DLCI reservados para el intercambio de mensajes entre el DTE y DCE.
53 . Un administrador de red est evaluando protocolos de autenticacin para un enlace PPP. Qu tres
factores podran conducir a la seleccin de ms de CHAP PAP como protocolo de autenticacin ? ( Elija tres
opciones).
establece identidades con un apretn de manos de dos vas
utiliza una autenticacin de tres vas peridicamente durante la sesin para volver a confirmar las identidades
el control por el host remoto de la frecuencia y el calendario de los eventos de inicio de sesin
transmite informacin de inicio de sesin en formato cifrado
utiliza un valor de la pregunta variables impredecibles para impedir ataques de reproduccin
hace que la intervencin del administrador de red autorizado el requisito de establecer cada sesin
54 . Qu tres afirmaciones son ciertas acerca de PPP? ( Elija tres opciones).
PPP puede utilizar circuitos sncronos y asncronos .
PPP slo se puede utilizar entre dos dispositivos de Cisco .
PPP transporta paquetes desde varios protocolos de capa de red en grandes instalaciones de combustin .
PPP utiliza LCP para establecer , configurar y probar la conexin de enlace de datos .
PPP utiliza LCP para acordar opciones de formato tales como la autenticacin , compresin y deteccin de
errores.