Cc Product Spec Til 43'000-04 Gc - 10# Asme Lng Iso Container _2

PRODUCT SPECIFICATION

CRYO CONTAINERS (Pty) Ltd TIL 43’000-04 GC LNG

(T75 ASME, 10 BAR)

43’000L VACUUM INSULTATED CRYOGENIC ISO CONTAINER FOR LNG AT 10 BAR

Product Specification : TIL 43’000-04 GC LNG (10 Bar)

April 2011 of 5

1. RATING

Nominal Volume (L) 43’400

Net Volume (L) 41’230

Payload (Kg) (LNG) 17’440 Kg

Length (mm) 12'192

Width (mm) 2'438

Height (mm) 2'591

MAWP (kPa) – Bar 10 Bar - (145 PSIG)

-Voidage (Ullage) Min 5%

Design and Testing

Tank: - in accordance with: - Type:

RID/ADR, IMDG & ASME VIII Div 1

T75 UN Portable Tank. US DOT

Frame - in accordance with: - Type:

ISO 1496/3 ML1 Beam Frame Design

Corner Castings Size and type code

ISO 1161 22T7

2. TANK

Inner Vessel

Material 304 Stainless Steel

Working Pressure 10 Bar (145 PSIG)

Design Code ASME VIII Div 1 & RID/ADR & IMDG ++

Inspection Authority Bureau Veritas

Baffles 5 in accordance with code

Material of construction EN 10028-7 304 Stainless Steel

Design Temperature Range -196 to +20 °C

Outer Jacket

Material Carbon Steel

Design Code EN 13530 & ASME & TPED

Material of construction EN 10210 S355 J2H / Supraform TM

Internal Design Pressure External Design Pressure Design Temperature Range

-1,0 bar 1,0 bar -20 to +50 °C



(T75 ASME, 10 BAR)



April 2011 of 5

Insulation

Type Multilaminar Super insulation

Vacuum Level Warm < 5 Microns

Vacuum Level Cold < 1 Micron

Holding time for LNG loaded at 84% filling level and 0barg

119 Days

Vacuum Couplings Manufacturer’s Design

3. FRAME & FITTINGS

Frame

Type Integral Reinforced

Hollow section Plates Rolled section

EN 10210 S355 J2H / Supraform TM 380 EN 10025 S355 K2G3C / Supraform TM 380 EN 10025 S355 K2G3

Material of construction Carbon Steel - SABS 300 WA

Dimensions (L) 12 192 x (H) 2 591 x (W) 2 438

MPGM 36 000 kg

Tare Mass (± 3% Tolerance) 12 000 kg

Fittings Can be altered to suit customer

Requirements

Flow diagram In accordance with drawing (Appendix 1)

Pipe Material 304 Stainless Steel

Pipe Sizes Liquid 40mm 1½ ” – Liquid to pump

Pipe Sizes Gas 40mm 1½” Liquid delivery 1½”

Pipe Sizes Press Raising Liquid inlet 20mm

Instrumentation Pipes 304 Stainless Steel

Valves Bestobell Stainless Steel Cryo globe valves

Trycocks At 85%, 90% & 95% of gross volume

Instrumentation

Differential Pressure Gauge (one)

WIKA - Calibrated in mm H20 with conversion table decal on tank.

Pressure Gauge (One) WIKA - Indicating tank gas phase pressure

Pressure Raising Coil

Capacity 120 - 160m³/hr 75 - 100 scfm

(or as specified by Customer)

Cabinet Arrangements

Operators Side Stainless steel upwards opening hinged door compartments.



(T75 ASME, 10 BAR)



April 2011 of 5

4. VESSEL TEST

Inner Vessel X-ray in accordance with Code. Hydraulic test, Black light test, helium mass-spectro meter, nitrogen thermal

Outer Jacket Helium mass spectrometer

5. PAINTING

First coat Hempadur Zinc (15360) 40 micron min DFT

Intermediate coat Hempadur Primer (15552) 40 micron min DFT

Final coat Hempathane (55210) 50 micron min DFT

TOTAL: 130 micron min DFT

Colour as per customer req

First coat Hempadur Zinc (15360) 40 micron min DFT

Intermediate coat Hempadur Primer (15552) 40 micron min DFT

Final coat Hempathane (55210) 50 micron min DFT

TOTAL : 130 micron min DFT



(T75 ASME, 10 BAR)



April 2011 of 5

6. TESTS AND HOMOLOGATIONS

Leak Test and Nitrogen Purge A helium mass-spectro meter leak test. Container will be delivered in a Nitrogen purged condition. Dry nitr oxygen, 1,0 bar pressure, Nitrogen dew point - 20°C). These tank containers are constructed according to an approved design. Each production unit is subject to testing and non-destructive examination as required by EN13530-2002, UIC and manufacturer’s own quality requirements. Each unit is inspected by the independent inspection authority Bureau Veritas. The container has been subjected to a stacking test load of 86400kg per corner post and is approved for 9-high stacking (8 x 24000kg). The UN Portable Tank fulfils the performance specification of the following International Organisation's regulations and recommendations and is supplied with their Approvals: � IMDG - T75 � RID/ADR – T75 � Additional Approvals: � TIR/Customs � CSC � UIC (34000kg with a super heavy decal) � TC Impact Approved

� TPED

� US DOT

7. DOCUMENTATION

The following documentation will be provided: • Certificate of cleaning (placed in the document holder). • Initial Inspection Certificate for each tank. • Name plate details. • List of transportable products.



(T75 ASME, 10 BAR)



April 2011 of 5

8. PRODUCTS

UN1971 Natural Gas, refrigerated liquid. UN1073 Oxygen, refrigerated liquid. UN1951 Argon, refrigerated liquid. UN1977 Nitrogen, refrigerated liquid

UN NO 1038 Ethylene, refrigerated liquid

9. OTHER

Walkways Not required.

Ladder Not required.

Earthing Connection 1-off stainless steel lug 60 x 50 x 2,5mm with a 20mm hole, is located at the rear of the tank frame.

Document Holder 1-off clear PVC document holder is provided. The holder is water-resistant and is fitted on the left lower rear of frame.

Customs Sealing Discharge valves and relief valves are provided with customs sealing devices.

Decals One set per tank as per code requirements. Owner logos supplied client, and applied by manufacturer.

Data Plates One set of stainless steel data plates per tank as per code requirements.

Valve Cabinet A valve protection cabinet, complete with hinged door, houses the gas and liquid line valves pressure gauge and thermometer.

Baffles Five sets of stainless steel plate baffles are fitted.

Cc Product Spec Til 43'000-04 Gc - 10# Asme Lng Iso Container _2

Documents

Transcript of Cc Product Spec Til 43'000-04 Gc - 10# Asme Lng Iso Container _2