Catalogo Aska

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE

AMPLIFIERS PageDISTRIBUTION AMPLIFIERS 25, 26DROP AMPLIFIERS 9, 27, 28IN-LINE AMPLIFIERS 39, 29

C O N N E C TORS AND A DA P TO R SADAPTORS 2ATTENUATORS 1, 30‘F’ CONNECTORS 1, 30HARDLINE CONNECTORS 2NUTS & WASHERS 3TERMINATOR 2, 31VOLTAGE BLOCKING COUPLER 1, 30

INSTALLATION ACCESSORIESCABLE CLIPS 5, 31CABLE TIES 5, 31ELECTRICAL TAPE 31GROUNDING BLOCKS & CLAMPS 3, 30HARDWARE 5, 31HI-PASS FILTER 14IN-LINE SURGE PROTECTOR 6LOCKING TERMINATORS 6SECURITY SHIELDS & TOOLS 6, 14SILICON GREASE & SEALANT 31SLEEVE ANCHOR 5, 31WALL PLATES 7, 8, 32WEATHER BOOTS 5, 31TELEPHONE PARTS & TOOLS 4, 32KEYSTONE WALLPLATES & JACKS 8FEED THRU BUSHINGS 7

P OWER INSERTERS & SUPPLIESPOWER INSERTERS 28, 29POWER SUPPLIES 27, 28, 29

S ATELLITE PRO D U C T SANGLE FINDERS 41CABLE ASSEMBLIES 30COMPASS 41DIRECTIONAL TAPS 23DIPLEXER 14, 35, 40HEADEND AMPLIFIERS 39IN-LINE AMPLIFIERS 39LEVEL 41MULTI-SWITCHES 36, 37, 38POWER INSERTERS & SUPPLY 29

SATELLITE FINDERS & CHECKERS 41SPLITTERS 33, 34

PASSIVES PageA/B SWITCHES 6DIRECTIONAL COUPLERS 29DROP TAPS 24EQUALIZER 24FM TRAPS 24MATCHING TRANSFORMERS 24SEPARATOR/COMBINER 241000 MHz SPLITTERS

EPOXY BACK 15, 16HORIZONTAL PORTS 21SOLDER BACK 17, 18, 20TONGUE & GROOVE CASE 19, 20, 21VERTICAL PORTS 22

TV/FM SPLITTERS 24

SPECIALTY PRO D U C T SDIGITAL MODULATORS 10, 11RF MODULATOR 12SIGNAL COMBINERS 12

TO O L SCOAX STRIPPER 4, 30CRIMPING TOOLS 4, 30SECURITY TOOL 6PUNCH DOWN TOOL 4, 32

WIRELESS ACCESSORIESMMDS COMBINERS 13

GENERAL INFORMATIONINDEX 42TERMS AND CONDITIONS 43WARRANTY INFORMATION 43

TABLE OF CONTENTS

F-59SG & F56SGwith Silicon Gel and O-Ring

SILICONE GEL

INTERNAL SEALING O-RING

MODEL # DESCRIPTION PLATING TOOL CABLE TYPEF-59D Die-cast 7/16” Nut Nickel AHX-596 RG-59/UF-59G All Brass with 7/16” Nut Gold Zinc " "F-59GW With O-Ring & 7/16” Nut Gold Zinc " "F-59SG O-Ring & Silicone Gel,7/16”Nut Gold Zinc " "F-56D Die-cast 7/16” Nut Nickel AHX-596 RG-6/UF-56G All Brass with 7/16” Nut Gold Zinc " "F-56GW With O-Ring & 7/16” Nut Gold Zinc " "F-56SG O-Ring & Silicone Gel 7/16”Nut Gold Zinc " "F-56SW Smooth Ring All Brass 7/16”Nut Nickel RTC-360 "F56-342Q All Brass, with 7/16” Nut Nickel AHX-360 RG-6 QuadF56-360UG Universal Crimp, All Brass Gold Zinc AHX-360 RG-6 Tri/QuadF56-360UT Universal Crimp, All Brass Tin " "F56-324T All Brass Tin AHX-596 RG-6 "F59-290T All Brass Tin AHX-596 RG-59 "F7-413G All Brass Gold Zinc AHX-7 RG-7F7-413T All Brass Tin " "AF-11 With O-Ring Nickel CR-596 RG-11AF-11C With Center Pin Tin AHX-11 RG-11

F-TYPE MALE CONNECTORS — CRIMP-ON

F-59 & F-56 Series7/16” Large Nut

AT T E N UATORS AND VO LTAGE BLO C K

VBCVOLTAGE BLOCK

5-2150 MHzReturn Loss

5-1450 MHz - 20 dB1500-2150 MHz - 15 dB

FAM-(*)FIXED ATTENUATOR

5-2150 MHz20 dB Return Loss

3, 6, 8, 10, 12, 16, & 20 dB

SAT-(*)DC POWER PASSIVEFIXED ATTENUATOR

5-2150 MHz15 dB Return Loss

3, 6, 8, 10, 12, 16, & 20 dB

FeaturesTrue 360 degree compression onto the cable insuring superior RFShielding performance of 95 dB shieldingBuilt-in O-ring inside connector for perfect moisture proof7/16” large hex nut for easier installationReduces assembly time and simplifies installationUse ASKA Model CTL - 100 crimping tool

WITH SEPARATE RINGAF-11 - For RG-11/U

F56 - 342QFor RG-6 Quad

shield coax

AF-11C - For RG-11/U 0.460 O.D.

Attached ring with fixed pin

F-56SWSmooth ring with O-ring

FPL-56 -for RG-6 coax cableFPL-56Q -for RG-6 Quad shield cable

After Crimped

COMPRESSION SEAL CONNECTORS

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE1

New

Patent No.#139072

F-CONNECTORS AND A DA P TO R S

RCA-59MALE RCA PLUG

Crimp-on type for RG-59 Cable

RCA-81RCA FEMALE SPLICE

PF-59PUSH ON ADAPTER

F-Female to Push-On F-Male

BFAF-Female to BNC Male

FF-RF-FEMALE TO RCA MALE

BFMF-Male to BNC Female

RCA-FRCA FEMALE TO

F-Male

AF-90RIGHT ANGLE

F-Female to F-Male

AF-90PRIGHT ANGLE

F-Female to Push-On F-Male

AF-59TIG - 75 Ohm Terminator5-2050 MHz25 dB Return Loss

AF-59TB75 Ohm TERMINATOR

AC/DC Blocked

TWIST-ON CONNECTORFTO-59 - For RG-59/UFTO-56 - For RG-6/U

HARDLINE CABLE CONNECTORS & A DA P TO R S

ADAPTORS

FEED-THRU CONNECTORS PIN CONNECTORS

TERMINATOR

KS-KSMALE SPLICE

All Brass, Rotational

FF-KSF-FEMALEKS Adapter

All Brass

CON-81UUNIVERSAL

FEMALE SPLICECan splice .500” pin or RG-11

Feed-thru connectors.

FMA-115F-Male to .500” pin

Connector orRG-11 Feed-Thru connector

Universal Design

TRM-1KS PORT

Terminator

RG-11 Feed-Thru connectorCON-11 - All Zinc Diecast

CON-500.005” Feed-Thru Connector

For half inch cableAll Brass

Pin ConnectorPIN-500 - for flexible Half-inch

(i.e. TFC# TX10-15)

FM-500F-.male to .500” adapter for

flexible hardline cables(i.e. TFC# TX10-15)

RIGHT A N G L E A DA P TO R S TERMINATO R S

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE 2


F - FEMALE and MALE SPLICES

G ROUNDING BLOCKS - 1GHz and 2.3GHz type

ZINC DIECAST F-SPLICES

DIGITAL F-SPLICE - HIGH RETURN LOSS - 5-2300 MHZ

AF-81MFEMALE SPLICECast Construction, Machine threaded

AF-81NWFEMALE SPLICE W/Nut & Washer,

NWNUT AND WASHER

AF-81BFEMALE SPLICE

Machine threaded. All brass

AF-71F-MALE SPLICE

AF-81G2 GHz Brass Splice

28 dB High Return Lossfor 5-2300 MHz

AF-81GD2 GHz Zinc Diecast Splice

Machine Threaded28dB Return Lossfor 5-2300 MHz

AF-71GF-MALE SPLICE28dB Return Lossfor 5-2300 MHz

ZINC DIECAST GROUND BLOCKS FOR DUAL CABLE SYSTEM

GB-1GROUNDING BLOCK

with Zinc Die-cast Splice

GB-2GROUNDING BLOCK with two Zinc Die-cast

Splices

GB-2DDUAL GROUNDING BLOCK

with two zinc die-cast splices. Two holes & set screws for separate ground wires.

GB-1G GROUNDING BLOCKBrass Splice-Cast Base

28 dB Return Loss5-2300 MHz

GB-1GD GROUNDING BLOCK

Zinc Diecast Splice usingCircular Contact Pin 25-28 dB

Return Loss 5-2300 MHz

GB-2GD GROUNDING BLOCKWith two Zinc DiecastSplices using CircularContact Pin 25-28 dB

Return Loss - 5-2300 MHz

GB-3GD DUAL BLOCK

Two 4 m/m holes andset screws for two

separate ground wires28dB Return Loss 5-2300 MHz

PREMIER GROUNDING BLOCK SERIES - HIGH RETURN LOSS - 5-2300 MHZ

NewNew

New New New

TELEPHONE MODULAR CRIMPING TOOL & PUNCH DOWN TO O L


HEX CRIMPING TO O L S

HEX CRIMP TOOLAHX-596

For RG-59/U and RG-6/U connectorsAHX-11

For RG-11/U connector (ASKA No. AF-11C)

HXR-596RATCHET HEX CRIMP TOOLFor RG-58/U, RG-59U, RG-62

and RG-6/U connectorsi.e. F-male, BNC, and TNC.

DELUXE HEX CRIMP TOOLAHX-360 .324 and .360 Hex

For F56-342Q & F56-360 all F-59 & F-56

AHX-7 .413 Hex For F7-413 Connector

CABLE STRIPPERS

STR-1COAXIAL CABLE STRIPPER

For standard and Teflon, RG-59 and RG-6/U cableAdjustable blades (2-cut type)

NOTE: Spare blades (STR-1B) available from stock

- 2 Step Cable Stripper- w/ Replaceable cartridge- For RG-6, 58, 59, & 62

- 2 Step Cable Stripper- w/ Replaceable blades- For RG-8, 11 & 213

MCT-2DELUXE MODULAR CRIMPING TOOL

Cut, Strip and Crimp, Metal ConstructionFor 2, 4 & 6 Contact Modular Plugs

MCT-3DELUXE MODULAR

RATCHET CRIMPING TOOLCut, Strip and Crimp, Metal Construction

For 8P8C/RJ-45, 6P4C/RJ-11

PDT-1IMPACT PUNCH DOWN TOOLFor use with terminal Block 110/88

With Impact adjustment. Punch & cut withreversible blade

CTL-100COMPRESSION RATCHET TOOL

Compatible with most Compression type Connectorsin the market, including Aska model FPL-56

and FPL-56Q Connectors

COMPRESSION RATCHET TO O L

STR-3SELF ADJUSTING BLADES

spare cassette (STR-3B) available from stock

STR-11Coaxial Cable Stripper For RG-11

New New

New New


CABLE CLIPS

CC-6 For RG-59/U cable 3/4" nailCC-6L For RG-59/U cable 1" nailCC-7 For RG-6/U cable 7/8" nailCC-7L For RG-6/U cable 1" nailCC-155 For Dual RG-6U cable 7/8" nailCC-155L For Dual RG-6U cable 1" nailCC-11 For RG-11U cable 1" nail

CC-155CC-155L

CC-7CC-7LCC-11

CC-6CC-6L

CABLE TIES

A-2Q-SPAN CLAMP

Galvanized Steel Bolt and Aluminum Clamp

AGC-1GROUND CLAMPFits 1/2" - 1-3/8" Pipe

SPLIT BOLTSB-4 NO. 4WIRESB-8 NO. 8WIRE

AGC-2Bonding Connector

For meter pan

A-3/83/8" GROUND CLAMP

A-5/85/8" GROUND CLAMP

ANC-1SLEEVE ANCHOR

With Hex Nut (3/8" x 2¼") For heavy dutyapplications in solid concrete, hollow block

and brick. Ideal for installation of DishAntenna on concrete or Block.

COPPER GROUND STRAPSA-24-6 6" StrapA-24-12 12" Strap

A-21-44 FT. GROUND ROD

WITH CLAMP

A-10“P” HOOKPlated Steel

Features:• Fits RG-59 and RG-6 cable over

F-Male fittings.• UV Resistance Rubber made.

AWB-1RUBBER BOOT

CABLE TIES (Black)U/V Resistance, UL Approved

Looped Max. BundlePart # Length Tensile DiameterCT-8 7.5" 50 lbs. 2"CT-11 11" 50 lbs. 3"CT-15 14" 50 lbs. 4"

INSTALLATION HARDW A R E

Note: Available in Black (B) or White (W). Specify color when ordering

New New


AST-1SECURITY SHIELD TOOLUse with SS-2S or SS-1TSecurity Shields

INSTALLATION ACCESSORIES

SECURITY SHIELDS

SS-1T - 1-1/8" MetalScrew-on Shield

SS-2S - 1-1/8" Metal Slip-on Shield

AB-95A/B SWITCH - PUSH BUTTON TYPE

ABS-1COAXIAL A/B SWITCH

ECONOMY COAXIAL SWITCH

AB-4A/B SWITCH - PUSH BUTTON TYPE

AB-5HI-ISOLATION A/B SWITCH

Slide Lever TypeFeatures:• High 90 dB ISOLATION exceeds FCC specifications.• Heavy duty zinc die-cast inner housing.• Double backed tape and mounting screws supplied.

C OAXIAL RF A/B SWITC H E S

PT-1

PT-1INLINE SURGE PROTECTOR

The PT-1 is ideal for protection from

lightning for CATV converters,

decoders, TV sets, VCR, Satellite

receivers,or any other Electronics

used at home or office.

LT-1LOCKING TERMINATOR

Aluminum BodyImpedance: 75 Ohm + 5%

S U RGE PRO T E C TO RLOCKING TERMINATO R S

SECURITY SHIELDS AND TOOL

Specifications:ABS-1 AB-4 AB-5 AB-95

Frequency Range: ..............5-1750 MHz ..................................Insertion Loss: .......... -0.7 dB Max ..................................Isolation: (dB Min.)

5-1000 MHz -60 -90 -90 -901000-1750 MHz -50` -60 -60 -60

Return Loss: (dB Min.)5-1000 MHz -15 -20 -18 -20

1000-1750 MHz -13 -16 -15 -16Number of Input: 2 2 2 2


W ALL PLAT E S

FEED-THRU BUSHINGS

AWP-DRJWITH TWO PHONE

JACKS (RJ-11)

Note: All wall plates available in colors of Ivory or White and individually polybagged with two mounting screws. *Specify (W) as a suffix when ordering white plates, for example AWP-81W etc.

(Available in black or ivory. Please specify when ordering)

SWP-10WALL PLATE

FOR SATELLITERIBBON CABLE

ABP-1BLANK WALL PLATE

WITH 3/8" HOLE

AWP-81WITH ONE F-81 SPLICE

AWP-81DWITH TWO F-81 SPLICES

AWP-81RJWITH ONE PHONE JACK

(RJ-11) & ONEF-81 SPLICE

FTB-56 FTBD-56

AWP-81DRJWITH ONE PHONE

JACK (RJ-11) & ONE F-81 SPLICE

Features- Protects drop cables- Provides neater cable installations- Secures flow-thru cable and seal opening

FTB-56FTBD-56

For RG - 6 cableFor Dual RG 6 cable

AWP-RJWITH PHONEJACK (RJ-11)


K E YS TONE W ALLPLATES AND INSERT S

KEYSTONE WALLPLATES

KWP-0Plastic Wallplate

Blank

KI-BLBlank Insert

KI-BLRCA Female

Coupler

KJ -RJ11With RJ11 6P4C Keystone Jack

White or Ivory

KJ5E-NSUnshielded Type

White, Ivory, or Red

KJ5E-HSHalf Shielded TypeWith Cable Holder

(Black Only)

KJ5E-FSFull Shielded TypeWith Cable Holder

(Black Only)

KI-STFST FiberCoupler

KI-BNCBNC Female

Coupler

KI-F2F-splice all brass

5-2300MHz25dB Return loss

KI-FIF-Splice all brass

5-1000MHz20dB Return loss

All wallplates and Inserts in colors of Ivory(IV) or White(W), except KJ5E-HS & KJ5E-FS.Specify color when ordering. KJ5E-NS available in color of Ivory, White and Red

KWP-1Plastic Wallplate for

1 Keystone Jack


2 Keystone Jacks


4 Keystone Jacks


6 Keystone Jacks

LOADED INSERTS FOR KEYSTONE WALLPLATE

KEYSTONE RJ-11 JACK CAT-5e KEYSTONE JACKS - RJ-45 SERIES

CAT 5E INLINE COUPLER

KJ-81FS (SHIELDED)KJ-81NS (UNSHIELDED)

- Ideal for linking an exit network cable run or to extend your patch cables

- Capable of handling LAN speeds of up to CAT-5E 100Mbps.

- Meets TIA/EIA 568A 11801 Category 5Eenhanced specifications

Available in shielded an unshielded version

KI-RCAFRCA Jack to F-Female

Our Cat-5e keystone jacks are developed for high speed network application. The jacks result in performance to meet EIA/TIA568A Category 5E enhanced specifications. Every jack includes an easy tool to provide punch down termination. this alsoreduces installation time by allowing the quick 4 pair cable termination of 26-22 AWG wires.

KI-BPAudio Binding PostBlack or Red Avail.

Specify color when ordering

New New


H O M E N E T WORKING AMPLIFIERS

IDEAL FOR HOME NETWORKING PANEL

General Specifications for MDA seriesFrequency Range: Forward Path 54- 1000MHz

Reverse Path 5-42MHzComposite second order -62dBc MaxComposite triple beat -74dBc MaxCross Modulation -75dBc MaxSurge Protection: 6KV IEEE C62.41-1991 ring wave (all ports)RFI shield 100dB Min.Hum Modulation(dBc) 75dBcInput Capability: 117dBuV at 1dB compression

The New MDA Series are designed with the highest headroom available in a distribution house drop amplifiers. Traditionalpanels are not designed to handle the radical variations in Strengths that have come about with HDTV. The new technologiessuch as HDTV create special problems for current video distribution panels. The new MDA series can handle an extremely widerange of input signals from current NTSC and digital TV In the future. The MDA-18R is a Single CATV or UHF/VHF off-air input with 8 TV outputs with 4.5dB gain on each port with 5-42MHzreturn path for bi-directional system for use with cable modem and pay- per- view applications. The MDA-31R, MDA-32R,MDA-34R, MDA-38R are Triple inputs (One CATV/ANT and 2 Modulated signals) with one, two, four and eight TV outputswith 5-42MHz return path for Cable modem and pay-per-view applications. All MDA series may be remotely powered from themedia center using the ASKA Model PS-9 Power supply using coaxial cable, when power is not available at the installations.

Forward Path Group Delay(3.58 MHz span)Channel 2 20ns MaxChannel 3 10ns MaxOther channels 5 ns Max

Return Path Group Delay(1MHz span)5 - 30MHz 20ns Max10-20MHz 5ns Max

Power Supply Voltage 12VDC 300mADimension 6-1/4"W x 3"D x 1-1/2"HConnector & impedance F-type, 75 ohms

Specifications:Model No. MDA-31R MDA-32R MDA-34R MDA-18R MDA-38RNumber of ports:

Inputs 3 3 3 1 3Outputs 1 2 4 8 8

Forward gain (dB Max)CATV/ANT IN 14 10 7 4.5 4AUX IN 7 4 1 N/A 2

Return Path Loss (dB Max) -1.5 -4 -8 -11 -12Isolation: (dB Min)

CATV to Aux input -30 -30 -30 N/A -30AUX Ports input -18 -18 -18 N/A -18OUT to OUT -20 -20 -20 -20 -20

Noise Figure: (dB)CATV / ANT port 7 7 7 7 7AUX port 11 11 11 N/A 11

Return loss (dB Min) 20 20 20 20 20

MDA-31R3-INPUT- 1 OUTPUT

MDA-34R3-INPUT- 4 OUTPUTS



MDA-18R1 INPUT- 8 OUTPUTS

New New


DIGITAL AUDIO & VIDEO MODULATO R S

Specifications:Model No.: RFDM-1 RFDM-3Output Frequency Range: 470 - 860 MHz 470 - 860 MHz

UHF Channels: Ch. 14-78 Ch. 14-83CATV Channels: Ch. 65-135 Ch. 65-139

Video Freq. Response: + 1 dB + 1 dBNoise Figure: 6 dB 6 dBAural Intercarrier Stability: 4.5 MHz + 3 KHz 4.5 MHz + 10 KHzFrequency Accuracy: + 5 KHz + 20 KHzVideo Input Level: 1V p-p 1V p-pAudio THD: 0.4% 0.4%Output Level: + 10 dBmV + 15 dBmVVideo S/N Ratio: 52 dB 52 dBAudio S/N Ratio: 50 dB 50 dBPower Requirement: ........... 117 VAC/60 Hz .............Number of input: 1 3Antenna input: N/A YES

The RFDM-1 and RFDM-3 modulates a video and left/right audio signal ofVCR, satellite receivers, security camera, etc. to a user selected TV channels.RFDM-1 is a single input Mono Modulator. RFDM-3 is a 3 channel input Monomodulator. Both modulators incorporates a commercial grade design intended fornon-adjacent placement of the modulated channels in any free area of UHF bandor the CATV ULTRA band. The channel selection of RFDM-1, UHF or CATVULTRA channels can be done by a built-in switch and the channel is digitallydisplayed on channel indicator. The agile design provides maximum flexibilitywhile allowing installers to maintain an inventory of only one model to cover all NTSC channels easily.

Features:• Compact design for easy installation. •.Combined stereo input to Mono.• Professional picture quality. • Eprom channel memory.• Covers UHF Channels 14-74 and • Multiple TV distribution.

CATV ULTRA Channels 65-135. • RFDM-1 Output channel• LED channel display selectable by built-in dip switch• FCC approved for RFDM-1 and RFDM-3 on front panel.

APPLICATION:

��

��

��

��

��!��

��

�"��

�#��##

$��

��

��

��

��

��

��

�

�

�

��

��

��

RFDM - 1DIGITAL UHF MODULATOR

SIZE: 2-3/4"W x 3-1/2"D x 1-1/8"H

“FCC” A P P RO V E D

“FCC” A P P RO V E D

RFDM - 3DIGITAL AUDIO/VIDEO3-INPUT MODULATOR

RFDM-1 Single Input RFDM-3 Triple Input>


MMUULLTTII-CCHHAANNNNEELL DDIIGGIITTAALL MMOODDUULLAATTOORRSS

RFDM-10Mini modulator

Single input3.4”W x 4.4”D x 1.1”H

RFDM-100Deluxe modulator

Single input

RFDM-200Deluxe Modulator

Dual inputs

RFDM-300Deluxe Modulator

Triple inputs

Front view Rear view

The Aska Multi-channel Digital Modulators accept the audio/video outputs from one, two and three video sourcesRespectively and create one, two and three in-house television channels, either UHF channel of Ch-14 - Ch-83 orUltra CATV channels of Ch-65 - 139. The sources of video/audio input can be a VCR, DVD, CCTV camera, Satellite Receivers, etc.RFDM-10 is a single input mono modulator, housed in a mini Aluminum case.RFDM-100 is a single input , RFDM-200 is a dual inputs, and RFDM-300 is a triple inputs mono modulator,housed in a deluxe metal housing.All of modulators feature frequency-agile tuning and just push the channel selector button to choose the desiredChannel and the internal microprocessor digitally sets the modulator to the exact channel specification.All modulator comes with power supply and instruction sheet for easy set-up.In case of combining Off-Air or CATV signal with modulated signals, recommend to use Aska Model SP-21G2-way splitter which is available from stock.Depend on the Modulator and number of channels, 6-Ft Stereo dubbingcable (Aska #CSD-6) are required which can be supplied from Aska stock.

Specifications (RFDM-10, 100, 200 & 300) RF OutputOutput Frequency Range: 470-860MHz

UHF channels Ch-14 - 83CATV channels (ultra) Ch-65-139

Impedance: 75 OhmOutput Level: 13dBmV per channelA/V ratio: 16dBVideo Frequency stability: +20KHzAudio Frequency stability: 4.5MHzSpurious response: -50dBINPUTSVideo input: 75% Min. 1V, p-pVideo impedance: 75OhmAudio input: 1Vp-p Min.Audio impedance: 10K unbalance

General SpecificationsDimensions:

RFDM-10 3.4”W x 4.4”D x 1.1”HRFDM-100,200,300 6.7”W x 5.1”D x 2.0”H

Connectors:RF outputs F-type connectorsVIDEO/AUDIO inputs RCA JackPower DC Jack

Power Requirement: 117VAC/60Hz - 15VDC/300mAOperating temperature: 32oF - 120oF

New

New


SIGNA L COMBINERS

The model ASC-3A and ASC-4A amplified signal combiners have a built-in UHF/VHFamplifier for 15 dB Gain at ANT input which is able to compensate for any loss fromlong run of coax cable or any other facts where signal amplification is required.With this ASC-3A and ASC-4A, there are no need for additional UHF/VHF amplifiersfor where need long run cable or in weak off-air signals area.

ASC-3A - FOR CHANNEL 3 AMPLIFIED COMBINERASC-4A - FOR CHANNEL 4 AMPLIFIED COMBINER

Applications:• Multi-TV set operation without the use of high isolation switches.• Allows the use of TV remote controls to switch between off-air and cable converter.• Allows simultaneous recording and viewing of premium channels and off-air signals.• Satellite receiver programs insertion into home MATV system.

TV

TO TV

COMBINER

CH OUTPUT

PAY TV UNIT

ASC-3MOR ASC-4M

VCR

ANTSATELLITEOR MMDSANTENNA

SIGNAL COMBINERSASC-3 - FOR CHANNEL 3ASC-4 - FOR CHANNEL 4

The ASKA signal combiners are designed with high quality six-stage bandpass and bandstop filters withadjustable balancing attenuators. This enables the user to combine a locally originated channel 3 or 4 intoan existing home MATV system containing adjacent channels.

VHF RF MODULATOR - A NA LOG T Y P E

INSTALLATION

Features:• Dimensions: 3.1"W x 2"D x 1"H. (ASC-3M). • Low insertion loss and low cost.• Miniature and durable zinc die-cast cases. • High unwanted signal attenuation. (-35 dB Rejection)• Supplied with double back tape for easy • Adjustable attenuators for signal balancing.

placing combiners anywhere.

MINI SIGNAL COMBINERSASC-3M - FOR CHANNEL 3ASC-4M - FOR CHANNEL 4

Specifications:Video Carrier Output: 150 mVVideo Input Impendance: 75 or 1K Ohm switchableOutput Impendance: 75 OhmsVideo Input Level: 1V P-P NTSC Negative sync.Video Out Level: 10 dBmVOutput Return Loss: Ch-3 12 dB

Ch-4 15 dBPower Requirements 120 VAC, 60 Hz, 5WConnectors: RCA Jack for audio/video

F-Connector for RF output

AMPLIFIED MODELS

RFM-1VHF RF MODULATORFeatures:• VHF modulation from Audio

and Video signal.• Allow the additional channels

of VCR, DVD and Satellite receiver to Ch-3 or Ch-4.


Features: • Zinc die-cast case for outdoor use.• Filters MMDS spurious signals.• Prevents MMDS signal leakage to UHF/VHF antenna.• Power passive to MMDS block converter.• DC blocked to the UHF/VHF antenna.

Applications:• Separation of VHF/UHF signals and MMDS signals• High isolation combining of VHF/UHF antenna

and a wireless MMDS block converter.

The SCS-33DC and SCS-33A allows MMDS wireless signals and the local UHF/VHF off-air signals to be combined onto one cableentering the home, while preventing the MMDS aeronautical band signals from radiating backwards through the off-air antenna.Filtering on the MMDS input eliminates spurious down converter products from interfering with the off-air channels.The SCS-33DC provides highpass filtering for the wireless MMDS Super-band input channels.The SCS-33A provides highpass filtering for the wireless MMDS Super-band input channels and the UHF/VHF antenna input isamplified by a low noise amplifier which provides a net gain of 4 dB after high isolation combiner circuit. The directionalamplifier prevents MMDS radiation from the UHF/VHF antenna.

Specifications:Model No. SCS-33DC SCS-33ABandwidth: VHF/UHF 54-216 MHz 470-870 MHz Bandwidth: VHF/UHF 54-216 MHz 470-870 MHz

Insertion Loss: 4.0 dB 6.5 dB Gain: 10 dB 10 dBBandwidth: (MMDS): 116-128 MHz 222-408 MHz Noise Figure: 4.5 dB 4.5 dB

Insertion Loss: 4.0 dB 6.5 dB Bandwidth: (MMDS): 116-128 MHz 222-408 MHzPort to Port Isolation: 40 dB Min. 40 dB Min. Insertion Loss: 4.5 dB 6.5 dB

Spurious Rejection: Spurious Rejection:Ch. 2-6 Ch. 7-9 (Min.) Ch. 7-11 Ch. 12 Ch. 1315 dB 28 dB 35 dB 20 dB 15 dB

Port to Port Isolation: 30 dB Min. Port to Port Isolation: 40 dB Min.Power Passing on MMDS input only - 12 VDC 1000 mA Power Passing on MMDS input only - 12 VDC 1000 mA

Power Consumption: 85 mA 12 VDC

MMDSANTENNA

DOWNCONVERTER

DC VHF/UHFANTENNA

COMBINER

DCRF

ASU-2SPLITTER

SCS-33A

POWERINSERTER

TV

TV

WIRELESS MMDS COMBINERS

SCS-33DCPASSIVE COMBINER

SCS-33AACTIVE COMBINER


CABLE MODEM INSTALLATION PA RT S

MULTI-MEDIA DATA BRANCH with Built-in High Pass Filter

The Model MDX-1 is designed for current 2-way cable when installing modem On to CATV system. The high isolation more than 40dB between data and TV ports at reverse band prevents tuner from saturation caused by strong uplink signals.The inter-modulation problem caused by the ferrite material is completely solved by the built-in diplexer in MDX-1.

Features:· Low Insertion loss· High Rejection

Specifications:Frequency Range: 5 - 1000MHzInsertion Loss: (Max)

IN to TV 5-42MHz - 40dB54-1000MHz - 2dB

IN TO DATA 5-42MHz - 2dB54 - 1000MHz - 9dB

Isolation (TV-DATA) 5-42MHz - 40dB54-1000MHz - 22dB

Return Loss: (Min) 10dB

DCW1G-6 or 9Wall mount

Directional couplerSolder back

DCM1G-6 or 9Mini Directional coupler

Solder back

MDX-1Modem/TV diplexer

HPF-54Pass 54-1000MHz

40dB rejection20dB Return Loss

SS-3L2-1/2” long security Shield

For use with HPF-54High pass filter

The most common configuration is installing the cablemodem at the same location as the customer’s computersystem. This cable configuration generally has a longercoaxial drop cable and a shorter CAT-5 network cable.This configuration also allows the customer to easily checkthe modem status lights.

HIGH PASS FILTER SECURITY SHIELD TYPICAL MODEM/TV INSTALLATION

MDX-1

· High Return Loss· Easy to install

New

New

New


ALL PORTS POWER PASSIVE

5-900 MHz UHF/FM SPLITTERS - ECONOMY

Specifications: Model No.: SP-16G

Bandwidth (MHz): 5-50 54-400 400-500 500-750 750-1000Insertion Loss: (dB) Max.: 13 13 14 14 15Isolation (dB) Min.: 25 27 28 28 25Input Return Loss (dB): 16 17 17 18 16Dimension: .................... 3-15/16" W x 9-5/8" L x 1-3/8" H ....................

SP-30 SP-40 SP-60 6-WAY SPLITTER3-WAY SPLITTER 4-WAY SPLITTER SP-80 8-WAY SPLITTER

1000 MHz 16-WAY SPLITTER

SP-16G - 1 GHz 16-WAY SPLITTER

The SP-16G Vertical splitter features a printed circuit board to provide outstanding performance. The 16-way splitters may beused where cascading several splitters to meet the demands of MDU is needed. Coupled with ASKA 1 GHz Directionalcouplers, an operator may run as many as 48 drops to a particular area. No power passing circuit.

SP-2M SP-20 WALL MOUNT 2-WAY SPLITTERMINI 2-WAY SPLITTER 2-WAY SPLITTER SP-2W - Epoxy Back

SP-21GW - 1 GHz Solder Back


Specifications:

Model No. ASU-2 & ASU-2DC ASU-3 & ASU-3DC ASU-4 & ASU-4DC ASU-8Bandwidth: (MHz) .................................................... All models 5-1000 MHz ...............................................Insertion Loss (dB Max.)

5-500 MHz 3.5 6 7 11500-1000 MHz 4.5 6.5 9 14

Isolation (port-port) (dB Min.)5-500 MHz 20 20 20 20

500-1000 MHz 25 20 20 20Input Return Loss (dB Min.) 18 17 18 11No. of DC pass port: ASU-2 -2 ASU-3 -3 ASU-4 -4 8

ASU-2DC -1 ASU-3DC -1 ASU-4DC -1

5-1000 MHz POWER PASSING SPLITTERS

ALL PORTS POWER PASSIVE SPLITTERS

Features:• Full 5-1000 MHz Frequency Range.• High quality zinc die-cast housing - Anticorrosive chromate finish with machine

threaded ports.• Multiple capacitors and ferrite core circuit design for best specifications for

5-1000 MHz - Ideal for MATV, CATV, SMATV and MMDS systems.• DC power passing to all ports for ASU-2, ASU-3, ASU-4 & ASU-8 Splitter.• Power passing to one port for ASU-2DC, ASU-3DC & ASU-4DC Splitters.

• Typical application for ASU-2DC Series are:• Combine non-preamped antenna and antenna with mast mounted

preamplifier on a single down lead.• Split downward signal to remote non-powered location while allowing

power to antenna preamplifier.• Combine MMDS powered down converters to an all channel antenna where

a combination of non-powered and powered lines need to be broughttogether on a common line.

ASU-2 2-WAY SPLITTER ASU-3 3-WAY SPLITTER ASU-4 4-WAY SPLITTER

ASU-8 8-WAY SPLITTER

ASU-2DC 2-WAY SPLITTER ASU-4DC 4-WAY SPLITTERASU-3DC 3-WAY SPLITTER

ONE PORT POWER PASSIVE SPLITTERS


SP-21G2-WAY SPLITTERSpecifications:Bandwidth MHz: 5-40 40-400 400-600 600-1000Insertion Loss:

(dB Max.) 3.5 3.8 3.8 3.8Isolation Port to Port:

(dB Min.) 20 30 30 25Input Return Loss:

(dB Min.) 20 24 24 20

SP-31G 3-WAY SPLITTER - EQUAL LOSS PORTSSP-31GU UNBALANCE LOSS (1 x 3.5 dB 2 x 7.5 dB)Specifications:Bandwidth MHz: 5-40 40-400 400-600 600-1000Insertion Loss: (Equal Loss Circuit)



(dB Min.) 20 25 25 20

SP-41G4-WAY SPLITTERSpecifications:Bandwidth MHz: 5-40 40-400 400-600 600-1000Insertion Loss:



(dB Min.) 18 20 20 20

SP-61G6-WAY SPLITTERSpecifications:Bandwidth MHZ: 5-40 40-400 400-600 600-1000Insertion Loss:

(dB Max.) 10 11 11 13Isolation Port to Port:

(dB Min..) 16 24 25 20 Input Return Loss:

(dB Min.) 15 20 21 13

SP-81G8-WAY SPLITTERSpecifications:Bandwidth MHZ: 5-40 40-400 400-600 600-1000Insertion Loss:



(dB Min.) 20 20 20 15

1 GHZ C ATV SOLDER BACK SPLITTERS -130 dB RFI

Features:• Tin plated zinc die-cast housings for perfect • Applications vary from headend combining to typical drop

corrosion protection and grounding. installations. This splitter series should be used where increased• Completely soldered back provides the highest bandwidth is being designed into the distribution systems.

possible RFI shielding more than -130 dB. • Printed circuit board ensures consistent RF performance and high • High precision machine threaded F-ports. port to port isolation.• NO DC power passing design. • Available with equal Loss ports or unbalanced Loss ports for

3-way splitters.


SP-31GDC3-WAY SPLITTER - EQUAL LOSS TO ALL PORTSSpecifications:Bandwidth: 5-1000 MHzInsertion Loss: 6.5 dB Max. (all ports)Isolation 25 dB Min.Return Loss: 20 dB Min.Power Pass: One port only

5-1000 MHz SOLDER BACK SPLITTERS - DC PASSIVE

SP-21GDC2-WAY SPLITTERSpecifications:Bandwidth: 5-1000 MHzInsertion Loss: 4 dB Max.Isolation 35 dB Min.Return Loss: 25 dB Min.Power Pass: One port only

SP-41GDC4-WAY SPLITTERSpecifications:Bandwidth: 5-1000 MHzInsertion Loss: 8 dB Max.Isolation 25 dB Min.Return Loss: 22 dB Min.Power Pass: One port only

UHF/VHF ANTENNA(54-860 MHz)

orCATV (5-1000 MHz)MMDS

SP-21GDC

DC

DownConverter

SetTop

USED AS COMBINER

TV

UHF/VHF ANTENNA(54-860 MHz)

orCATV (5-1000 MHz)MMDS

SCS-33DC

SP-21GDC

DC

DownConverter

SetTop

SetTop

USED AS SPLITTER

TV TV

Features:• High quality zinc die-cast case with anticorrosion chromate finish.• Mounting tabs with screws & ground block.• 100% Soldering of cover for -130 dB RFI shield.• Printed circuit board ensures consistent RF performance and

high port to port isolation.• Power passive to one port, and other ports are DC Blocked.

Applications:• Combine non-preamped antenna and antenna with mast mounted

preamplifier on a single down lead.• Split downward signal to remote non-powered location while

allowing power to antenna preamplifier.• Combine MMDS powered and powered lines need to be brought

together on a common line.• Combine MMDS powered down converters and CATV line of

5-1000 MHz need to be brought in on a common line.

APPLICATION


TGS-21G2-WAY SPLITTERSpecifications:Bandwidth MHz: 5-40 40-500 500-750 750-1000Insertion Loss:



(dB Min.) 20 22 22 20

TGS-31G 3-WAY SPLITTER - EQUAL LOSS PORTSTGS-31GU UNBALANCE LOSS (1 x 3.5 dB 2 x 7.5 dB)Specifications:Bandwidth MHz: 5-40 40-500 500-750 750-1000Insertion Loss: (Equal Loss Circuit)



(dB Min.) 20 22 22 20

TGS-41G4-WAY SPLITTERSpecifications:Bandwidth MHz: 5-40 40-500 500-750 750-1000Insertion Loss:



(dB Min.) 18 22 22 20

1 GHz CATV SPLITTERS - HIGH QU ALITY

1 GHz HIGH QUALITY SPLITTERS WITH TONGUE & GROOVE HOUSINGS

Features:

• All ports no power passing design with blocking capacitors • Applications vary from headend combining to typical providing excellent intermodulation performance for low drop installations. This splitter series should be used distortion interactive operation, such as cable Modem. where increased bandwidth is being designed into the systems.

• Nickel plated zinc die-cast housings for perfect • Printed circuit board ensures consistent RF performance corrosion protection and grounding. and high port to port isolation.

• Tongue & groove housing design provides high • F-ports spaced 1 inch center to center to accommodate security RFI Shielding for -130 dB. sleeves and tools.

• High precision machine threaded F-ports. • Available with equal loss port or unbalanced loss ports for • 360 degree F-port base for full seating of sealing sleeve. 3-way splitters.


2-WAY SPLITTERSHQS-2TG - Tongue and Groove Back CoverHQS-25SB - Soldered Back CoverSpecifications:Bandwidth MHz: 5-15 15-42 45-750 750-1000Insertion Loss:



(dB Min.) 25 28 25 25Output Returnloss: 25 35 25 25

(dB Min)

3-WAY SPLITTERS (Balanced Circuit)HQS-3TG - Tongue and Groove Back CoverHQS-3SB - Soldered Back CoverSpecifications:Bandwidth MHz: 5-15 15-42 45-750 750-1000Insertion Loss: (Equal Loss Circuit)



(dB Min.) 25 28 25 25Output Return Loss 25 35 30 28

(dB Min)

4-WAY SPLITTERSHQS-4TG - Tongue and Groove Back CoverHQS-4SB - Soldered Back CoverSpecifications:Bandwidth MHz: 5-15 15-42 45-750 750-1000Insertion Loss:



(dB Min.) 20 28 30 28

1 GHz MULTI-MEDIA DIGITAL READY SPLITTERS

HQS-2TG & HQS-2SB

HQS-3TG & HQS-3SB( Balanced Circuit)

HQS-4TG & HQS-4SB

New

Features of HQS splitter series:* Digital Ready 5 - 1000MHz splitters

Available in 2, 3 and 4-way* Zinc Alloy Die-cast Housing with Flat port ends* Available both soldered (SB series) and/or

Tongue/Groove back (TG series) for 120dB RFI* Compliant with SCTE specifications for

both electrical and mechanical specifications* Blocking capacitors on all ports for blocking

Hum modulation (-60dB)* SMT P.C.B. technology for consistent specs.

General Specifications:* 6KV Surge protection on all ports

IEEE 587 (C62.41-1991) category A3 standard(6KV, 100 KHz ring wave surge )

* 360 degree center seizing pins* Spurious signals including 2nd order harmonics,

(Discrete 2nd & 3rd Order distortion) -60dBmV Min. measuring with a +55dBmV input 30MHz Carrier on each port

* 28dB Min. Input and output Return Loss at 15 - 42MHz* 25dB Min. port-to-port Isolation * Operating temperature -40F to +140F

Output Return Loss: 25 35 30 28(dB Min)


HRS-21G2-WAY SPLITTERSpecifications:Bandwidth MHz: 5-40 40-400 400-600 600-1000Insertion Loss:



(dB Min.) 20 25 25 20Dimensions: 1.55"L x 3.2"W

HRS-31G3-WAY SPLITTER - EQUAL LOSS TO ALL OUTPUTSSpecifications:Bandwidth MHz: 5-40 40-400 400-600 600-1000Insertion Loss:




HRS-41G4-WAY SPLITTERSpecifications:Bandwidth MHz: 5-40 40-400 400-600 600-1000Insertion Loss:




1 GHz ONE SIDED HORIZONTAL PORTS SPLITTERS

��

��

��

The new HRS series of horizontal splitters are especially designed to haveINPUT and OUTPUT ports on one side of the housing. This allows bettercable management as well as installation in the small entry box withoutjamming up the box space with traps and cables as shown in illustration.

TONGUE & GROOVE HOUSINGS -130 dB RFI

Features:• All ports no power passing design with blocking capacitors providing

excellent intermodulation performance for low distortion interactive operation, such as cable Modem.

• Nickel plated zinc die-cast housings for perfect corrosion protection.• High precision machine threaded F-ports.• Input and output ports are placed on one side horizontally for

allowing better cable management and installation in small entry box.• Tongue & groove housing design provides high RFI Shielding for -130dB. • This splitter can be used where there is not much space allowed or

in a small entry box.• Printed circuit board ensures consistent RF performance and high port

to port isolation.


1 GHZ C ATV V E RTICAL SPLITTERS -130 dB RFI

TGV-21G 2-WAY SPLITTERSpecifications:Bandwidth MHz: 5-40 40-400 400-600 600-1000Insertion Loss:



(dB Min.) 20 25 22 22

TGV-31G 3-WAY SPLITTER - EQUAL LOSS PORTSSpecifications:Bandwidth MHz: 5-40 40-400 400-600 600-1000Insertion Loss: (Equal Loss Circuit)



(dB Min.) 20 20 22 22

TGV-41G 4-WAY SPLITTERSpecifications:Bandwidth MHz: 5-40 40-400 400-600 600-1000Insertion Loss:



(dB Min.) 18 20 22 22

TGV-61G 6-WAY SPLITTERSpecifications:Bandwidth MHZ: 5-40 40-400 400-600 600-1000Insertion Loss:


(dB Min.) 16 24 25 20 Input Return Loss:

(dB Min.) 18 20 22 22

TGV-81G 8-WAY SPLITTERSpecifications:Bandwidth MHZ: 5-40 40-400 400-600 600-1000Insertion Loss:



(dB Min.) 9 15 15 12

Features:All ports no power passing design with blocking capacitors providing excellent intermodulation performance for low distortioninteractive operation, such as cable modem.

• No DC power passing design. • Printed circuit board ensures consistent RF performance • Vertical input and outputs allow close mounting in lock and high port to port isolation.

boxes for easy access of cable connections. • F-ports with machine threaded spaced 1 inch center to • Chromate treated zinc alloy housing for best corrosion protection. center to accommodate security sleeve and tools.• Tongue & Groove housing design for better RFI shielding. • Dual heavy duty ground blocks ensures proper grounding.


Tap Value: 6 9 12 16 20 24 27 30INSERTION LOSS

5-50 MHz 2.4 1.5 1.4 .6 .6 .5 .5 .554-500 MHz 2.4 1.4 1.4 .8 .8 .7 .7 .7

500-900 MHz 2.5 2.1 1.8 1.5 1.2 1.1 1.1 1.1900-1000 MHz 2.5 2.1 1.8 1.5 1.2 1.1 1.1 1.1

ISOLATION(Tap Out)

5-50 MHz 20 24 28 30 35 39 40 4254-500 MHz 23 28 29 33 36 39 44 46

500-900 MHz 20 25 27 30 32 34 34 35900-1000 MHz 18 22 24 25 28 29 30 32

Tap Values (dB): 9 12 16 20 24 27 30INSERTION LOSS

5-50 MHz 1.5 1.4 .6 .5 .5 .5 .554-500 MHz 1.4 1.4 .8 .7 .7 .7 .7

500-900 MHz 2.0 1.7 1.0 1.0 1.0 1.0 1.0900-1000 MHz 2.1 1.8 1.5 1.1 1.2 1.0 1.0

ISOLATION(Tap Tap) 5-500 MHz: 20 dB

500-1000 MHz: 15 dB(Tap Out) Same as Model DCM1G & DCW1G

1 GH Z DIRECTIONAL COUPLERS -130 dB RFI

Specifications: for DCM1G & DCW1G

WALL MOUNT DIRECTIONAL COUPLER

DCW1G - SOLDERED BACK COVER

Specifications: for DC21G

2-PORT DIRECTIONAL COUPLER

DC21G - SOLDERED BACK COVER

Specifications: for DC41G

4-PORT DIRECTIONAL COUPLER

DC41G - SOLDERED BACK COVER

MINI DIRECTIONAL COUPLER

DCM1G - SOLDERED BACK COVER

Features:• High Quality zinc die-cast housing• Soldered back cover for RF shielding for -130 dB RFI.• Full 5-1000 MHz frequency range.• Printed circuit board ensures consistent RF performance and high port to port isolation.

General Specifications:RETURN LOSS

5-50 MHz 15 dB50-900 MHz 20 dB

900-1000 MHz 15 dB

TAP TOLERANCE5-900 MHz +1 dB

900-1000 MHz +1.5 dB

Tap Values (dB): 8 12 16 20 24 30INSERTION LOSS

5-50 MHz 2.8 1.2 1.0 .6 .6 .654-500 MHz 2.8 1.4 1.4 .8 .7 .7

500-900 MHz 2.8 1.5 1.6 1.0 1.0 1.0900-1000 MHz 3.5 2.5 2.0 1.8 1.4 1.4

ISOLATION(Tap Tap) 5-500 MHz: 25 dB

500-1000 MHz: 15 dB(Tap Out) Same as Model DCM1G & DCW1G

* Specify dB value when ordering.

SOLDER BACK HOUSING


FM SPLITTERS & SEPA R ATO R S

FM TRAPFMT 95- 108MHzFT-88 88- 108MHz

M ATCHING T R A N S F O R M E R S

BACK-MATC H E DD ROP TA P S

INLINE S LO P E E QU ALIZER

UV-SJUHF/VHF BAND SEPARATOR/COMBINERVHF - 40-220MHzUHF - 470-890MHz

HL-SJVHF LOW/HIGH BAND SEPARATOR/COMBINERLO - 5-108MHzHI - 175-216MHz

TAP-1-( )Freq. Range 5 - 1000MHzAvailable in dB value of7, 12, 17, &23dbSpecify Tap value when Ordering

FM-TVSTV/FM SPLITTERSolder BackFM - 88-108MHzTV - 54-890MHz

MT-75PPUSH-ON MATCHING TRANSFORMERFeatures:• Push-on F-fitting for easy use.• Non-strip piercing screws.• High density PVC case.

MT-75 MATCHING TRANSFORMER

OUTDOOR MATCHING TRANSFORMERSFeatures:• Heavy duty sealed molded housing.• Weather boot included for weather protection.• Resistance to moisture and sun.

AOB-1 - With twin lead and spade lugs.

AOB-3 - With wire leads

EQ2G- ( )2GHz Equalizer

0.5 dB

950

dB

4 dB

6 dB

10 dB

2 dB

EQ2G-3

EQ2G-6

EQ2G-91750 2150 MHz1450

EQ1G- ( )1GHz Equalizer

1000 MHz

0.5 dB

EQ1G-3

EQ1G-6

EQ1G-9

EQ1G-12

EQ1G-16

40 MHz

dB

3 dB

6 dB

9 dB

12 dB

16 dB

1.0 dB

EQ1-G EQ2-G

The EQ1G and EQ2G are an inline equalizer that compensates for the unevenBroadband frequency response often present in distribution system.The EQ1G is designed for 1GHz CATV system and EQ2G is for 950-2150MHzSatellite system. Typical slope are shown in chart below.

Equalizing value:EQ2G- 3, 6, and 9dBSpecify dB value when ordering

Equalizing value:EQ1G- 3, 6, 9, 12 and 16dBSpecify dB value when ordering


UHF/VHF/FM DISTRIBUTION AMPLIFIERS

AM-1UVUHF/VHF/FM HOME

10 dB AMPLIFIER

AM-20UVUHF/VHF/FM SLOPED

20 dB AMPLIFIERwith Tilt Control

25 dB GAIN HOME AMPLIFIERAM-125 — With FM Trap AM-125G — With Gain Control & FM Trap

AMP-15UV15 dB DISTRIBUTION AMP

AMP-25UVUHF/VHF/FM

25 dB DISTRIBUTION AMP

AMP-36UVUHF/VHF/FM

36 dB GAIN DISTRIBUTION AMP

HOME AMPLIFIERS:Specifications:Model No. AM-1UV AM-20UV AM-125 AM-125GBandwidth: ....................................... All models 54-890 MHz ..................................................................Gain: 10 dB 20 dB 22 dB 22 dBMax. Input: VHF 7-Chs. 36 dBmV 20 dBmV 20 dBmV 20 dBmVMax. Input: UHF 4-Chs. 22 dBmV 11 dBmV 11 dBmV 11 dBmVNoise Figure: ....................................... All models 5dB VHF & 7dB UHF ...............................................Tilt Control: N/A 0-10 dB N/A N/AGain Control: N/A N/A N/A 0-10 dBFM Trap: N/A N/A YES YESPower Requirement: ....................................... All models 117 VAC, 60 Hz or 220 VAC, 50 Hz ...........................

*Note:For AM-1UV, AM-20UV, & AM-125 Only. Specify power when ordering: 117 VAC or 220 VAC.

DISTRIBUTION AMPLIFIERSSpecifications:Model No. AMP-15UV AMP-25UV AMP-36UVBandwidth: N/A N/A 54-810 MHz

VHF 54-216 MHz 54-890 MHz 54-108 MHz Low/147-216 MHz HighUHF 470-890 MHz 470-810 MHz (Low)

Gain: (dB) VHF 15 dB 25 dB 31 dBUHF 12 dB 20 dB 36 dB

Max. Input: VHF 7-Chs. 36 dBmV 22 dBmV N/AMax Input: UHF 4-Chs. 20 dBmV 18 dBmV N/ANoise Figure: ....................................... All models 5 dB VHF & 7 dB UHF ................................................Gain Control: N/A N/A 0-15 dBFM Trap: N/A YES SW-1: (88 - 96 MHz) -20 dB

SW-2: (95 - 108 MHz) -20 dBPower Requirements: ............................................. All models 117 VAC, 60 Hz .....................................................


PUSH PULL CATV AMPLIFIERSWith Tilt and Gain Control

ACA-305 50 - 550 MHzACA-308 50 - 860 MHz

550 & 860 MHz CATV DISTRIBUTION AMPLIFIERS

AMP-25GT25 dB GAIN 1 GHz AMPLIFIER

With Tilt and Gain Control

1 GHz CATV DISTRIBUTION AMPLIFIERS

Note:Maximum output levels will vary with the number of channels. Exceedingspecific input levels will cause intermodulation and picture distortion.

Features:• Designed for home/apartment systems. • Adjustable Gain and Slope Control.• High Output - Low Noise. • Input and Output test points.• Push-Pull for Low distortion.

Specifications:Model No. ACA-305 ACA-308Bandwidth 5 - 550 MHz 50 - 860 MHzGain: 30 dB 32 dB+1Gain Control: 0-20 dB 0-18 dBMax. Output: 45 dBmV 45 dBmVTest Point - 20 dB - 20 dBNoise Figure: 6.5 dB 7.5 dBFlatness: + 1 dB + 1 dBInput Return Loss: (Min.) 15 dB 16 dBOutput Return Loss: (Min.) 12 dB 13 dBTilt Control: 0 -10 dB 0 -18 dBPower Requirement: ........ 115 VAC, 60 Hz, 4 W ........Operating Temperature: ............. -0o to + 50o C .............Dimensions: ........... 8"L x 4-1/2"D x 2"H ..........

Specifications:Model No. AMP-25GT ACA-301GGain: 25 dB 30 dBGain Control: 0-10 dB 0-20 dBMax. Output: 40 dBmV 46 dBmVBandwidth 54 - 1000 MHz 50 - 1000 MHzTest Point N/A -20 dBNoise Figure: 6.5 dB 6.0 dBCross Nodulation: -58 dB -60 dB2nd Order Intemod: -70 dB -70 dBFlatness +1 dB +1 dBInput Return Loss: 18 dB Min. 18 dBOutput Return Loss: 12 dB Min. 12 dBTilt Control: 0-10 dB N/AHum Modulation: -60 dB -65 dBCTB: -60 dB -65 dBPower Requirements: .................... 115 VAC, 60 Hz, 4 W .....................Dimensions: 6" L x 2" D x 1-1/2" H 9-3/4" L x 5" D x 2-1/2" H

ACA-301G30 dB GAIN 1 GHz AMPLIFIER

With Gain Control

Model No. ACA-305 ACA-308 AMP-25GT ACA-301GBandwidth MHz 50 - 550 50 - 860 50 - 1000 50 - 1000Gain (dB): 30 30 25 30Channel Capacity 77 125 140 140Maximum Output: 45 45 40 46(dBmV)


Specifications:

Model No. AM1G-10 AM1G-20NO. OF OUTPUT: ONE ONEBandwidth (MHz) 50-1000 50-1000 Gain (dB) 10 +1 20 +1Flatness Passband (dB) +1 +1Return Loss (dB) Min. 14 14Noise Figure (dB) 7 7RFI Shielding (dB) 130 130DIST. X-Mod. (dBmV) -70 -70

CTB (dBmV) -65 -65Max. Output (dBmV) +25 +30Power Consumption: 150 mA 12 VDCChannel Capacity: 151 151

1 GHz 2-WAY D ROP AMPLIFIERS

POWER INSERTERPS-3 - 120 VAC ADAPTORPS-32 - 220 VAC ADAPTOR

Features:• Ideal for long cable drops or multiple subscriber TV sets. 5 MHz to 1 GHz bandwidth and low noise figure.• Gain of 10 dB or 20 dB available with 1 dB flatness across entire bandwidth.• Both the amplifier and power transformer connectors are “F” type, allowing the use of coaxial cable readily available.• Comes with 120 VAC plug-in transformer (220 VAC option).• Solder back housing for -130dB RFI Shielding.

AM1G-10 & AM1G-20

* Each unit includes transformer (PS-3) 120 VAC/6W 12 VDC/150 mAOptional: ( PS-32) 220 VAC 50 Hz Transformer - 2 VDC/150 mA. * Specify when ordering.

1 GHz FORW ARD DROP AMPLIFIERS

1 GHz BROADBAND DROP AMPLIFIERS FOR HOUSE AND APARTMENT USE

10 dB or 20 dB GAIN FORWARD AND REVERSE DROP AMPLIFIERS

Specifications:

Model No. AM1G-102 AM1G-202NO. OF OUTPUT: ONE (2-WAY) ONE (2-WAY)Bandwidth (MHz)

Forward 50-1000 50-1000Reverse 5-40 5-40

Gain Forward (dB) 10 +1 20 +1Gain Reverse (dB) -0.6 -0.6Flatness Passband (dB) + 1 + 1Return Loss (dB) Min. 14 14Noise Figure (dB) 7 7RFI Shielding (dB) 130 130DIST. X-Mod. (dBmV) -70 -70

CTB (dBmV) -65 -65Max. Output (dBmV) +25 +30Channel Capacity: 151 151Power Consumption: 170 mA 120 VAC

* Each unit includes transformer (PS-3) 120 VAC/6W - 12 VDC/150 mAOptional: ( PS-32) 220 VAC 50 Hz Transformer - 12 VDC/150 mA.

* Specify when ordering.

Features: • Ideal for long cable drops or multiple subscriber TV sets. 5 MHz to 1 GHz bandwidth and low noise figure.• Gain of 10 dB or 20 dB available with 1 dB flatness across entire bandwidth.• Available in forward and return path type (AM1G-102 and AM1G-202) with power passive return path.• Both the amplifier and power transformer connectors are “F” type, allowing the use of coaxial cable readily available.• Comes with 120 VAC plug-in transformer (220 VAC option).• Solder back housing for -130dB RFI Shielding.

AM1G-102 - 10 dB GainAM1G-202 - 20 dB Gain


1 GHz MULTI-MEDIA HOUSE DROP AMPLIFIERS

DA1G-1RReturn path Amplifier

10dB gain

DAIG-10ONE OUTPUT

15 dB Gain

DAIG-20TWO OUTPUTS

11 dB Gain

Features:*1,2 and 4 ports models available*New 1-way Reverse Amplifier to

give subscriber upstream signals to boost*Sturdy Zinc Die-cast housings, with machine

threaded ports and solder back for 110dB RFI*Visible LED for unit power verification

*Fully compatible with all digital signalformats, forward and reverse

*All ports surge protection*18dB Min. Return Loss*5.5dB Low Noise figured*Universal powering, direct or line powered

The Aska House Drop Amplifiers; DAIG-10, DAIG-20, & DAIG-40 are Digital Ready and offer a passive return path forfuture growth into video, data and telephony signals. The passive return path allows digital signals from the customer, i.e.,phone, fax, modem or computer to travel back to CATV headends.The model DA1G-1R is new Return path Amplifier which amplify the return path signal of in-home devices such as cablemodem and 2-way set-top boxes. It provides 10dB of gain and enough headroom to support high signal levels fromin-home devices.

GAIG-40FOUR OUTPUTS

8 dB Gain

PS-3 POWER INSERTER120 VAC - 12 VDC/150 mA

PS-32 POWER INSERTER220 VAC - 12 VDC/150 mA

PI-10POWER INSERTERavailable from stock

Specifications:Model No. DA1G-10 DA1G-20 DA1G-40 DA1G-1RNo. of outputs: 1 Way 2 Way 4 Way 1-WayFrequency Range: Forward: ............................... 54 - 1000 MHz ................................................................................

Reverse: .....................................5 - 42 MHz ........................................... 5-42MHzPassband flatness: .................................... + 0.5 dB ................................................ +0.5dBNoise Figure: .................................. 5.5 dB Max ............................................ 5.5dBMaxGain (dB) Forward: 15 dB 11 dB 8 dB -2dBLoss (dB) Reverse: -0.7 dB -4.5 dB -9 dB +10dBRated Output Level: 25 dBmV 21 dBmV 17 dBmV 20dBmVReturn Loss, all ports: 18 dB Min. 18 dB Min. 18 dB Min 18dB MinPort-to-Port Isolation: N/A 25 dB Min. 24 dB Min. N/ACTB (dBc): -70 -70 -70 -70CSO (dBc): -60 -60 -60 -60Cross Modulation Distortions (dBc): -70 -70 -70 -70Surge Voltage Protection (All Ports Standard 0.5 Micro Sec. - 100 KHz ring wave) ............................... 6 KV - 200 A ..................................................................................RFI Shielding: (dB) 110 dB 110 dB 110 dB 110dBImpedance (Ohms): 75 75 75 75Power Supply: ....................... 120 VAC/12 VDC 150 mA ....................................................................Dimensions: 4-1/4" L x 3-1/2" W x 1-7/8" H for all models

Power Supply PS-3 is included in the unit

NewNewNewNew


P OWER SUPPLIES & POWER INSERTER/DC BLO C K

POWER SUPPLY with F-Female OutputPS-3 - 120 VAC, 12 VDC, 150 mAPS-32 - 220 VAC, 12 VDC, 150 mAPS-7 - 120 VAC, 18 VDC, 300 mAPS-9 - 120 VAC, 24 VDC, 600 mAPS-10 - 120 VAC, 24 VDC, 1000 mAPS-11 - 120V/AC, 24 VDC, 600MARCA Plug output for AMS-58 and LNC-16R

POWER SUPPLY with 6 Ft. LeadPS-6 - 120 VAC, 24 VDC, 600 mAPS-62 - 220 VAC, 24 VDC, 600 mAPS-6M - 120 AC, 24 VDC, 600 mA

with 3.5 mm Mini PlugPS-8 - 120 VAC, 24 VDC, 1000 mAPS-82 - 220 VAC, 24 VDC, 1000 mA

PI-10POWER INSERTER

Specifications:Frequency - 5-1750 MHzInsertion Loss - 0.5 dB Max.Capacity - 60 VDC 1 Amp

Specifications:Bandwidth: 40-950 MHzGain: 10 dB Min.Max. Input: 14 dBmV (7-Ch)Noise Figure: 4 dB Max.Power: 15-18 VDCPower Source: ASKA PS-1 InserterPower Consumption: 12 VDC

85 mA

P OWER INSERT E R S

LA-595 PS-1 TO TV

��LA-595 INLINE AMPLIFIER

40-950 MHz

PS-2DDUAL POWER INSERTER

40-950 MHz UHF/VHF INLINE AMPLIFIER

Features:• Provides power for both polarities

of LNB or two inline amplifiers.• Provides power for MMDS Down

Converter and Amplifiers.

Applications:• Block converted satellite systems, when extended cable

requires additional 40-950 MHz gain.• MATV antenna pre-amplifications.

��

��

��

��

��

��

��

�

��

�!"#�$��

��

��

��

PS-1POWERDIPLEXER

Specifications:Bandwidth: 5-2150 MHzInsertion Loss: 2.5 dBReturn Loss: 15 dB Min.Input Power: 117 VAC 60 HzDC Voltage: +18 +1 VDCMax Current: 300 mAPower X-former: UL approvedAvailable in both 110 and 220 VAC

* Specify voltage when ordering.

Specifications:Bandwidth: 5-2150 MHzInsertion Loss:

40-1450 MHz 0.10 dB1450-2050 MHz 1.0 dB

Return Loss: 15 dB Min.Isolation: 40 dB Min.DC voltage: +18 +1 VDCMax. Current: 500 mAPower X-former: UL ApprovedAvailable in both 110 or 220 VAC

* Specify voltage when ordering.


S ATELLITE INSTALLATION ACCESSORIES

F-MALE CONNECTORS F-59D - For RG59 CableF-56D - For RG6 Cable

Male SpliceAF-71 F-Male spliceAF-71G 2GHz splice

FEMALE SPLICEAF-81M - Zinc Die-cast BodyAF-81B - Brass BodyAF-81G - 2 GHz Splice

TWIST-ON CONNECTORFTO-59 - For RG-59/UFTO-56 - For RG-6/U

SPLICES VOLTAGE BLOCK

COMPRESSION

ATTENUATORS

TOOLS

STR-1COAXIAL CABLE STRIPPER

FAM (*)Fixed Attenuator

5-2150 MHz* Both available in 3, 6, 8, 10, 12, 16, & 20 dB

MCT-1PECONOMY MODULAR

CRIMPING TOOL

AF-11C For RG-11/U 0.460 O.D.

Attached Ring w/ Fixed pin

F-56SGFor RG-6 Cable with

Silicon Gel and O-ring

VBC - VOLTAGE BLOCK5-2150 MHz

FPL-56 -for RG-6 coax cableFPL-56Q -for RG-6 Quad shield

SAT-(*)Fixed 5-2150 MHz

Attenuator DC Power Passive

HEX CRIMP TOOLSAHX-596 For RG-59/U & RG-6/U connectorsAHX-11 For RG-11/U connector

CRIMP-ON CONNECTORS

CABLE ASSEMBLY

CRRSTEREO HOOKUP CABLE

Dual shielded audio cable with 2 RCA plugs. Color coded.

Available in 6' length. Color: Black

CSDSTEREO DUBBING CABLE

Triple coaxial cable with 3 RCAplugs. Available in 6' & 12'.

Color: Black

CSVHSUPER VHS CABLE

With 4-pin plug to 4-pin plug.Available in 6' & 12' cable.

Color: Black

CMFFY-ADAPTER

1 RCA Male to 2 RCA Females.Color: Black

CFMMY-ADAPTER

2 RCA Males to 1 RCA Female.Color: Black

TLC-7 - 7 Ft.TLC-15 - 15 Ft.TLC-25 - 25 Ft.

TELEPHONE LINE CORDModular plug on both ends. Color: Silver

SPLIT BOLTSB-4 NO. 4WIRESB-8 NO. 8WIRE

AGC-2BONDING CONNECTOR

FOR METER PAN

GROUND CLAMPS

AGC-1GROUND CLAMPFits 1" - 1/2" Pipe

A-3/8 - 3/8" GROUND CLAMPA-5/8 - 5/8" GROUND CLAMP

8 INCH FLAT CABLE


S ATELLITE INSTALLATION ACCESSORIES

SG-10SILICON GREASE - 3 Fluid oz.

RTV-3SILICONE RUBBER SEALANT

Clear, 3 Fl. Oz.

AF-59TIG5-2150 MHz

25 dB Return Loss

TERMINATORS

AF-59TB75 Ohm AC/DC Blocked

TERMINATOR

ET-6060 Ft. Electrical Tape (3/4" x 60')

Color: Black

CC-6 - For RG-59 CableCC-6L - For RG-59 CableCC-7 - For RG-6 CableCC-7L - For RG-6 CableCC-11 - For RG-11 CableCC-155 - For Dual RG-6 CableCC-155L - For Dual RG-6 Cable

AWB-1RUBBER BOOTFor both RG-59 and RG-6 Cable

ANC-1SLEEVE ANCHOR

With Hex Nut (3/8" x 2-1/4")For heavy duty applications

in solid concrete, hollowblock and brick.

CABLE TIES (Black)U/V Resistance, UL Approved

Looped Max. BundlePart # Length Tensile DiameterCT-8 8" 75 lbs. 2"CT-11 11" 75 lbs. 3"CT-14 14" 75 lbs. 4"

GROUNDING PARTS

PREMIER GROUNDING BLOCK SERIES - HIGH RETURN LOSS - 5-2300 MHz

COPPER GROUND STRAPSA-24-6 - 6" StrapA-24-12 - 12" Strap

A-21-44 FT. GROUND ROD WITH CLAMP

CABLE CLIPS

GB-1GDGROUNDING BLOCK

Zinc Die-cast Splice usingCircular Contact Pin25-28dB Return Loss

5-2300MHz

FC-88” Flat cable

GB-2GDGROUNDING BLOCK

with two Zinc Die-cast Splicesusing Circular Contact Pin

25-28dB Return loss 5-2300MHz

GB-3GDDUAL GROUNDING BLOCK

with 2 groundingholes for dual cable system 25-28dB Return Loss-5-2300MHz

GB-1G GROUNDING BLOCKBrass Splice Cast Base

using Circular Contact Pin25-28 dB Return Loss

5-2300 MHz

Slim line 8” flexible cable with“F” female connections molds towindow sills and door jams tomake installation easyNo need to drill holes through walls

Features:

New


TELEPHONE PLUG CRIMPING TO O L S

TELEPHONE ACCESSORIES

W ALL PLATES & CABLES

MCT-1PECONOMY MODULAR

CRIMPING TOOLStrip and Crimp, Metal ConstructionFor 2, 4 & 6 Contact Modular Plugs

Can crimp both handset and line plug

MCT-2DELUXE MODULAR

CRIMPING TOOLCut, Strip and Crimp, Metal Construction

For 2, 4 & 6 Contact Modular Plugs

MCT-3DELUXE MODULAR

RATCHET CRIMPING TOOLStrip and Crimp, Metal ConstructionFor 4, 6 & 8 Contact Modular Plugs

Can crimp both handset and line plug

TMA-1MODULAR SURFACE JACK

Converts hard wired 4-prong connecting blocks

to modular jack.Color: Ivory

TDA-2TWIN ADAPTOR

Two in one modular adaptor convert single jack to a double jack.

Color: Ivory

TMP-4FMODULAR PLUG

For flat cable4-Conductor

RJ-11

TMP-8FMODULAR PLUG

For flat cable (CAT-5e)8-Conductor

RJ - 45

TMC-3MODULAR INLINE

COUPLER4-ConductorColor: Ivory

AWP-DRJWITH TWO PHONE

JACKS (RJ-11)

AWP-81RJWITH ONE

PHONE JACK(RJ-11) & ONEF-81 SPLICE

AWP-81DRJWITH ONE

PHONE JACK (RJ-11) & ONE F-81 SPLICE

AWP-RJWITH PHONEJACK (RJ-11)

TLC-7 - 7 Ft.TLC-15 - 15 Ft.TLC-25 - 25 Ft.

TELEPHONE LINE CORDModular plug on both ends. Color: Silver

PDT-1IMPACT PUNCH DOWN TOOLFor use with terminal Block 110/88With Impact adjustmentPunch & cut with reversible blade

PUNCHDOWN TOOL


950-2150 MHz SATELLITE SPLITTERS

Features:

• Low cost, high performance Satellite splitter.• Heavy duty zinc die-cast cases.• Low thru Loss and High Isolation.• Available in all ports power pass, and

one port power pass.

SSP-4 - 4-WAY ALL PORT DC PASSIVESSP-4DC - 4-WAY ONE PORT DC PASSIVE

SSP-2 - 2-WAY ALL PORT DC PASSIVESSP-2DC - 2-WAY ONE PORT DC PASSIVE

Specifications: SSP-2 SSP-2DC SSP-4 SSP-4DCModel No. SSP-2AP SSP-21P SSP-2DS SSP-4AP SSP-41P SSP-4DS SSP-81P SSP-8DSInsertion Loss(dB Max.): 4 4 4 8 8 8 11 12Return Loss (dB Min.): 14 14 14 12 12 12 13 13Isolation (dB Max.): 21 21 21 20 20 20 20 20No. of DC Pass: 2 1 2 DS 4 1 4 DS 1 8 DS

TONGUE & GROOVE DIE-CAST HOUSING FOR -130 dB RFI WITH GROUND BLOCK

ECONOMY MODEL

DELUXE MODELFeatures:• Tongue & groove housing design provides high RFI Shielding for -130 dB, (2-Way and 4-Way splitters only).• Nickel plated zinc die-cast housings for perfect corrosion protection and grounding.• High precision machine threaded F-ports.• F-ports spaced one inch center to center to accommodate security sleeves and tools.• Printed circuit board ensures consistent RF performance and high port to port isolation.• 360 degree F-port base for full seating of sealing sleeve.• Available in all ports power passive, one port only passive and diode steered all ports power passive models.• Diode steered model (SSP-2DS, SSP-4DS and SSP-8DS) will pass DC power from any outputs back to input.

There is 0.8 VDC drop across the diodes which are included to prevent one receiver from passing power back to another receiver.

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

2-WAY SPLITTERSSP-2AP - All Ports DC PassSSP-21P - One Port DC PassSSP-2DS - All Ports DC Pass (Diode Steered)

8-WAY SPLITTERSSP-81P - One Port DC PassSSP-8DS - All Ports DC Pass (Diode Steered)

4-WAY SPLITTERSSP-4AP - All Ports DC PassSSP-41P - One Port DC PassSSP-4DS - All Ports DC Pass (Diode Steered)

CIRCUIT DIAGRAM


5-2150 MHz WIDEBAND SPLITTERS

TG2G-2 All ports power passive

TG2G-2DC One port power passive

TG2G-2DS All ports power passive

(Diode Steered)




(Diode Steered)




(Diode Steered)

Specifications:Model No. TG2G-2 TG2G-3 TG2G-4 TV2G-6 TV2G-8

TG2G-2DS TG2G-3DS TG2G-4DS TV2G-6DS TV2G-8DSTG2G-2DC TG2G-3DC TG2G-4DC TV2G-6DC TV2G-8DC

Insertion Loss: (dB Max.)5-950 MHz 4 dB 6 dB 8 dB 11 dB 12 dB

1000-2150 MHz 5 dB 8 dB 9 dB 15 dB 16 dBIsolation: 25 dB 22 dB 22 dB 22 dB 22 dBReturn Loss: 14 dB 14 dB 14 dB 15 dB 15 dBBandwidth: ................................................ All models 5-2150 MHz ....................................................................Impedance/connector: .................................... All models 75 Ohm and F-Female connectors ................................................

Features:• 5-2150 MHz Wideband ideal for Satellite DBS installation.• Able to split or combine signals on cable carrying both

UHF/VHF TV signals (54-860 MHz) or cable (5-1000 MHz) and satellite IF signals (950-2150 MHz).

• One output DC power passive models to supply power to Pre-amplifier or inline amplifier. (DC Series)

• Grounding Block attached.• All series uses tongue & groove cases for -130 dB RFI

shielding.

2-WAY SPLITTERS 3-WAY SPLITTERS 4-WAY SPLITTERS

TV2G-6 All ports power passive

TV2G-6DC One port power passive

TV2G -DS All ports DC passive

(Diode Steered)

TV2G-8 All ports power passive

TV2G-8DC One port power passive

TV2G-8DS All ports DC passive

(Diode Steered)

6-WAY SPLITTERS 8-WAY SPLITTERS


40-2150 MHz SATELLITE DIPLEXERS

SCS-5WPSATELLITE & UHF/VHF SPLITTERwith wall plate and phone jack

The SCS-5WP is the Wallplate with built-in Diplexer (SCS-2)and phone Jack (RJ-11).This is used as a splitter and installed directly on wall of inside the house.The wallplates come with two mounting screws and ANT andSAT is clearly marked for easy connection

Specifications: (ALL DIPLEXERS)SATELLITE IF PORT VHF/UHF PORTPass Band 950-2150MHz Pass Band 40-860MHzThru Loss 2.8dB Max Thru Loss 1.0dB MaxReturn Loss 10dB Min Return Loss 10dB MinStopband Attenuation: Stopband Attenuation:860MHz 32dB 750-950 MHz 30dB806MHz 40dB 1000-1100 MHz 45dB

Features:*Allows off-air signals and satellite

signals to be fed on a single cable.*Can be used either as splitter or combiner.*DC Power to LNB is provided from the

satellite port from receiver.*SCS-6 & SCS-6PR has two ground lugs

built-in*SCS-6 PR is specially designed to pass

12VDC regulated power to ANT port fromreceiver. This is to eliminate the use of power supply for UHF/VHF pre-amplifier.

Power Passing:*DC power pass to Sat input (18VDC) only to Output:

SCS-1, SCS-2, SCS-4TG, SCS-6 & SCS-5WP*DC power pass to both Sat and Ant inputs to output: SCS-1P*DC power pass to Sat port (18VDC) and Ant port (12VDC regulated): SCS-6PR

SCS-4TGDIPLEXER with ground port

Tongue & Groove CaseSize: 2.5"W x 2"D x 1”H

DELUXE DIPLEXER w/groundSize; 3.7” W x 2.7”D x 1”H

SCS-1 Sat port only DC passSCS-1P Sat & Ant port DC pass

SCS-2COMPACT DIPLEXER

Size: 2.3"W x 1.9"D x 1”H

SCS-6Compact Diplexer

with 2 Ground portsSize: 2.3”W x 1.9”D x 1”H

SCS-6PRANT port with regulated

12VDC Passing for Preamp PoweringSize: 2.3”W x 1.9”D x 1”H

2 Ground Lugs2 Ground Lugs


D E LUXE SATELLITE MULTI-SWITC H E S

40-2150 MHz MULTI-SWITCHES - ELECTRONIC T Y P E

RELAY SWITCHING DESIGN

PDS-34MMini 4-Way Multi-switch

SIZE: 3-1/2”D x 4”W x 3/4”H

PDS-34XEconomy 4-way Multi-switchSize: 2-1/4”D x 5.3”W x 1”H

LNC-38UP8-WAY SATELLITE MULTI-SWITCH

UNIVERSAL POWERING

PS-9F-port output

120 VAC - 24 VDC600 mA

PS-6 & PS-6M6 Ft. Power cable.

120 VAC - 24 VDC600 mA

Features:*Heavy duty zinc diecast case.With machine threaded ports

*Lightening protection circuit atANT port

*Built in amplifier at ANT port *Switch works with power from receiver

Features:Mini and light designFor small installation inLimited spaceLow loss design

Features:Small and light designWorks without extra powerF-port power jack forpower supply (PS-9)Two grounding lugs

Features:Deluxe zinc diecast caseWorks without extra powerWith mini Jack for extrapower supply (PS-6M)Low loss design

Specifications:Frequency Range: ANT 40-806MHz, SAT 950 - 2150MHzOutput Frequency: 40 - 2150MHzInsertion Loss: (dB Max) ANT- 3dB for PDS-34M and PDS-34X

12dB for PDS-38XSAT 4.5dB for PDS-34M and PDS-34X

6dB for PDS-38XIsolation: Horizontal and Vertical- 35dB Min

Specifications:Freq. Range-

ANT 40-806MHzSAT 950-2150MHz

Output Freq. 40-2150MHzInsertion Loss:

ANT - 5dB MaxSAT - 3dB Max

Isolation:H&V - 35dB Min.Out to out - 20dB Min.

Max Current from IRD - 70mA

Features:*Heavy duty aluminum cast

Housing with brass connectors*Built-in amplifier at ANT port to

cover insertion loss*Lightening protection at ANT port*Universal Power system for use with

both PS-6 or F-port type PS-9power supply

*Switch works with power from receiver

PDS-38X8Way Multi-switch

With Input Jack For External Power SupplySize: 5”D x 5-3/4”W x 1-1/4”H

LNC-34SATELLITE MULTI-SWITCH

WITH AMPLIFIED UHF/VHF PORT


S ATELLITE MULTI-SWITCHES

The ASKA Model LNC-16 & LNC-16R are designed forsixteen satellite receiver systems. These Multi-switches are usedto provide satellite signals of either LHCP (Horizontal) 18 VDCor RHCP (Vertical) 13 VDC polarization from one dish tomultiple receivers. These switches allow for each receiver to beindependently switched from horizontal or vertical channelsgiving full channel reception to each receiver.

LNC-16R16-way Rack Mount Multi switch2 LNB inputs

Specification: (LNC-16 & LNC-16R)LNB Input Frequency: 950-2150MHzPort-to-Port Isolation’s: 25dB Min.Insertion Loss: 6dB Max.Switching Voltage: 13V/18VDCPower Adaptor: 117VAC, 300mAConnectors: F-typeWeight: 4 lbsDimensions: LNC-16 18.5”Wx1.8”Hx4.8D

LNC-16R 19”Wx1.75”Hx4.75”D

Features:-Provides RHCP and LHCP switching for 16 receivers-Power adaptor supplies power to LNB’s-Ideal for smaller systems -Built-in amplifier to compensate for insertion loss-PS-11 600mA power supply is available from stockin case of extra power required

Features:*All ports designed vertically on top of case ideal to use for Home Networking Module*Cost effective distribution of the CATV/off-air antenna and DBS signal over one cables.*F-port output type power supply (ASKA Model PS-9)*Amplified circuit for both Satellite and CATV ports for low loss.

Specifications:

LNB Input Frequency: 950-2150MHzPort-to-port Isolations: 25dB Min.Insertion Loss:

Satellite: -2dBCATV/ANT +4dB gain

Switching voltage: 13V/18VDCPower Adaptor: 120VAC/600mA 24VDCConnectors: F-typeWeight: 6.2”Lx3.3”Dx1.5”H.

LNC-1616-WAY MULTI-SWITCH

TWO LNB INPUT

MSV-34A3IN-4OUTPUT MULTI-SWITCH

Rack Mounted Multi-Switches

16-WAY SATELLITE MULTI-SWITCHES

ALL PORTS ON TOP OF CASE FOR HOME NETWORK MODULE USE


22KHz Control - SATELLITE MULTI-SWITC H E S

AMS-2222KHz Pulse

Control Switch

AMS-54W5x4 Multi-Switch

22KHz control

22KHz PULSE CONTROL SWITCH

AMS-585x8 Multi-Switch 22KHz control

The AMS-54W and AMS-58 are 22KHz Control Multiswitches which works with Voltage from receivers. They are designed toallow the reception of satellitesfrom two or three orbital slots using multiple LNBs in a residential application.

AMS-54W has 5 inputs to 4 outputs AMS-58 has 5 inputs to 8 outputs.A 600mA 22KHz quasi square Wave is placed on top of the 13/18VDC when the additional satellite feeds are required.These devices enable the reception of DirectTV Para Todos and HDTV feeds in a multi LNB environment.

Specifications: AMS-54W AMS-58Passband Frequency: 40-2200 MHz 40-2200 MHzInsertion Loss:

40-862 -4dB -6dB950-2200 -5dB -8dB

Noise Figure: 4.8dB 4.8dBCross Polar Isolation: 30dB 30dBCurrent Consumption: 3mA 3mAControl Voltage: LNB A 18V / 0KHz LNB A 18V / 0KHz

LNB B 13V / 0KHz LNB B 13V / 0KHzLNB C 18V / 22KHz LNB C 18V / 22KHzLNB D 13V / 22KHz LNB D 13V / 22KHz

Power Requirements: *External power optionalPower Adaptor (not included) 24VDC 600mA(PS-9) 24VDC 600mA(PS-6M)RHCP Output (diode protected) 13VDC 13VDCLHCP Output (diode protected) 18VDC 18VDCLNB Current Draw (max) 250mA 250mA

Dimensions (w/connectors) 6.2”(w) x 1.2”(h) x 5”(d) 10”(w) x 1.2”(h) x 4.5”(d)

Weight (w/power supply) 2 lbs 2.10 lbs

Model AMS-22 is a solid state pin diode switch to selectbetween two LNBs controlled by the presence or absenceof a 600 mV, 22 KHz tone on the LNB voltage. All ports areDC connected. Ensure the satellite receiver can powerboth LNBs.

Passband 950-2150 MHzThru Loss 1.5 dBReturn Loss 13 dBIsolation 43 dBMax. Thru Current 500 mACurrent Requirement 20 mA plus LNBSwitch Control >200 mA KHz square waveDimensions HxWxD 1” x 4”x 2.5” incl. connectors


950-2150 MHz SATELLITE DISTRIBUTION AMPLIFIERS

S ATELLITE INLINE AMPLIFIERS

APPLICATION

LA-917 METAL CASE

INLINE AMPLIFIER40-2150 MHz 13 dB Gain

LA-917DDIE-CAST CASE

INLINE AMPLIFIERS40-2150 MHz, 15dB Gain

LA-9520 DIE-CAST CASE

INLINE AMPLIFIERS950-2150 MHz, 20 dB Gain

Specifications:Model No. LA-917 LA-917D LA-9520Bandwidth: 40-2150 MHz 40-2150 MHz 950-2150 MHzGain:

40-806 MHz 13 dB + 1 dB 15 dB + 1 dB N/A950-2150 MHz 11 dB + 1 dB 13 dB + 1 dB 20dB + 1dB

Noise Figure: 4 dB Max. 4 dB Max. 4 dB Max.Max. Output: 30 dBmV (12 Ch) 30 dBmV (12 Ch) 30 dBmV (12 Ch.)Power Consumption: ................. 22 VDC 40 mA ......................Housing: Metal Zinc die-cast Zinc die-cast

TO TVPS-1LA-917

SHA-30UP - 30 dB GAIN DUAL SATELLITE AMPLIFIER

INSTALLATIONS

Fig 1

The SHA-30UP is Dual polarization SatelliteHeaded Amplifier with LNB powering function.This may also be used as dual high level line extender.The model is specially designed to be used eitherBy conventional power supply (Aska #PS-8) or F-porttype Power Supply (Aska #PS-10).The use of F-port type power supply is excellent fora long cable run from power outlet to attic or anySites where there is no access nearby.PS-10 power supply is supplied with SHA-30UP.

Specifications:Bandwidth: 950-2200MHzGain: 30dB Min.Return Loss: 12dB Min.Isolation A&B: 55dBNoise Figure: 6dBLNB Voltage: 13VDC and 18VDCLNB Current Max: 350mAPower Supply: 120VAC-24VDC/1AmpPower consumption: 18VDC 450 mADimension: 6.5”W x 5”H x 1.1”D

��

�

�

��

��

��

��SHA-30

120VAC

120 VAC


��

��

��

��

�� !

�"#��"#�$��$$�

��

�"��+(

�"��

��

5-2150 MHz DUAL POLARIZATION TAP - 12 dB

Model STP-12D contains two 12 dB 1-way taps in one housing. This is for use in dual polarization distribution networks. It features excellent return loss, thru loss and tap loss characteristics. It is the finest unit of its type and is the unit of choice indual polarization distribution networks. A typical application is shown in Fig. 1.

STP-12D1-WAY 12 dB TAP

DUAL POLARIZATION

,&��

,&��

�

�

"��-��

,"��-��

%&

%& ��

��

��

��%&�-.�

��%&��#��

�"��

��

��-��

��

��%&�-. ��%&�-.� ��%&�-.� ��&��/-�%��%��%�&

��

Specifications:Bandwidth: 5-2150 MHzConnectors: F-type 75 OhmsDC Pass: In to out trunk DC pass

In to Tap DC blockTap Loss: 12 dB + 1 dBIn-Out thru Loss: 2 dB Max.Return Loss 18 dB Min.Isolation (tap-out): 25 dB Min.Dimensions: 3.1"D x 4"W x 1"H

DBC-1 -Passive Dual DiplexerDBC-1A -Active Dual DiplexerDBC-1PR -With 12VDC regulated

Power passing on ANT port

Specifications:Model No. DBC-1 DBC-1PR DBC-1AFrequency Range:............................................ 40-2150 MHz..........................Insertion Loss: (dB Max.)

40-860 MHz (UHF/VHF) -12 -3.0 -1.0950-2150 MHz (LNB) -3.5 -3.5 -3.5

Input Return Loss: (Min.) 13 dB 13 dB 13 dBTap Return Loss: (Min.) N/A N/A N/AIsolation between LNB: (Min.) 20 dB 20 dB 20 dBSwitching Voltage: N/A N/A N/ADC Power Passing (LNB) yes yes yesDC Power Passing (ANT) N/A 12VDC Regulated N/APower Consumption: N/A 12VDC/200mA 18VDC 50mA

The DBC series Dual Diplexers are designed forCascade use in dual polarization, tapped trunkDistribution systems. They are wideband allowingUHF/VHF as well as satellite IF signals to pass.They give very low thru loss and allows DC to passalong the trunk lines.Each of the tap outs can select either thru trunkSignal depend on 14VDC or 18VDC supplied from reciever.DBC-1 is passive on ANT, DBC-1A is Amplifiedon ANT port. DBC-1PR pass Regulated 12VDCpower to ANT port from receiver to powerpreamplifier. They should be used conjunction withASKA Distribution Amplifier SHA-30 as in Fig. 1

DBC-1PR

RX1

STP-12

RX2

Fig. 1

40-2150MHz DUAL DIPLEXERS

PRE-AMP

117VAC

BV+13VUHV/VHFAntenna

SatelliteDish

FIG 1

AV+18VSHA-30UP

SHA-30


S ATELLITE FINDERS AND ACCESSORIES

The SF-1000 is designed to aid in the alignment of the satellite dish which includes two meters, allowing easyalignment of dual satellite single dish installations. When peaking, the dish signal level can be viewed for bothLNBs simultaneously, making alignment quick and easy. The detector drives a meter and variable frequencyaudio tone. The dish is then aligned for maximum meter deflection or highest pitch tone. A gain control allowsa wide range of input signal levelsThe SF-1000 operate from, 11-24VDC on the coaxial cable. Connection to the receiver is optional with the

SF-1000 but extends battery life between charges. The SF-1000 allow measurement of voltage on the coaxialcable and also measures LNB current. Includes an internal rechargeable Nicad battery pack, carrying case withstrap and a Wall plug power supply. The battery pack is switchable between 13 and 18V output, allowingeither polarization to be selected when used with voltage switches LNB.

DUAL SATELLITE SIGNAL LEVER METER

SF-95SATELLITE FINDER

with Audio Tone

SF-90SATELLITE FINDER

WITH “LED” INDICATORSNo audio tone

SF-1000Dual Satellite

Signal level Meter

Features:950-2050 MHz bandwidthPocket Size and LightweightHigh Sensitive Illuminated MeterAudio Tone Function on SF-95

Specifications:Input Frequency: 950-2150 MHzInput level: -25 dBm to -75 dBmSensitivity: 7 Micro Volts under condition

of LNB gain 55 dB, three carrierC/N of 15 dB

Power Supply: +13/+18 VDC supplied from IF lineOperating Range: LNB GAIN: 52-60 dB

AF-701M4” ANGLE FINDER

Magnetic Base

LEV-2

ANGLE FINDER COMPASSESLEVELSATELLITE CHECKER

Features:• Miniature 1" dia.• Lightweight

Features:• 360 Degree vials•Economy Model• Plastic body

C-25MINI COMPASS

Specifications:Frequency Range: 950-2150MHzImpedance: 75 ohmsConnectors: F-typeAudio Tone: yesLNB voltage measurement: yesLNB current measurement: yesInsertion loss: 4dB MaxInput Level Range: -30 to +4 dBm - 1 Transponder

-39 to -5dBm - 8 transponders-42 to -8 dBm - 16 transponders

Dimensions: 4.9" x 7" x 3.8"Weight: 42 oz (1,200g)Wall plug charging voltage: 24VDCBattery Capacity: 600mA per hourBattery life: 1.5 hours between charge

SF-99SAT-CHECKER

*Just insert between LNB and Receiver*Easy to check presence of Satellite

signal and power by built-in LED lights


-A-A-10 ....................................5A-2 ......................................5A-21-4 ................................5A-24-(*) ..............................5A-3/8 ..................................5A-5/8 ..................................5AB-4....................................6AB-5....................................6AB-95..................................6ABP-1 ................................7ABS-1 ................................6ACA-301G ........................26ACA-305 ..........................26ACA-308 ..........................26AF-11 ..................................1AF-11C..........................1, 30AF-59TB ......................2, 31AF-59T1G ....................2, 31AF-701M ..........................41AF-71 ............................3, 30AF-71G ........................3, 30AF-81B..........................3, 30AF-81G ........................3, 30AF-81GD ............................3AF-81M ........................3, 30AF-90 ..................................2AF-90P................................2AGC-1 ..........................5, 30AGC-2 ..........................5, 30AHX-360 ......................4, 30AHX-7 ..........................4, 30AM1G-(*) ..........................27AM-1UV ............................25AM-125 ............................25AM-125G ..........................25AMP-15UV........................25AM-20UV ..........................25AMP-25GT........................26AMP-25UV........................25AMP-36UV........................25AMS-22 ............................38AMS-54W ........................38AMS-58 ............................38ANC-1 ..........................5, 30AOB-1 ..............................24AOB-3 ..............................24ASC-(*) ............................12ASC-(*)A ..........................12ASC-3M/4M ......................12AST-1..................................6ASU-(*) ............................16ASU-(*)DC ........................16AWB-1 ..........................5, 31AWP-81 ........................7, 32AWP-81D......................7, 32AWP-81DRJ..................7, 32AWP-DRJ......................7, 32AWP-RJ ........................7, 32-B-

BFA ....................................2BFM ....................................2

-C-C-25 ..................................41CC-11............................5, 31CC-155 ........................5, 31CC-155L ......................5, 31CC-6 ............................5, 31CC-6L ..........................5, 31CC-7 ............................5, 31CC-7L ..........................5, 31CFMM ..............................30CMFF................................30CON-11 ..............................2CON-500 ............................2CON-81U ............................2CRR-(*) ............................30CSD-(*) ............................30CSVH-(*) ..........................30CT-(*) ............................5, 31CTL-100..............................4

-D-DAIG-(*) ............................28DBC-1PR ..........................40DBC-1 ..............................40DBC-1A ............................40DC21G-(*) ........................23DC41G-(*) ........................23DCM1G-(*) ........................23DCW1G-(*) ......................23

-E-EQIG-(*) ............................24EQ2G-(*) ..........................24ET-60 ................................31

-F-F-7-413G/T ........................1F-56-(*) ........................1, 30F-59-(*) ........................1, 30FAM-(*) ........................1, 30FC-8..................................31FF-KS ................................2FF-R....................................2FM-88 ..............................24FM-500 ..............................2FMA-115 ............................2FMT ..................................24FM-TVS ............................24FPL(*) ................................1FTB-56................................7FTBD-56 ............................7FTO-(*)..........................2, 30

-G-GB-1 ............................3, 31GB-1G ..........................3, 31GB-1GD........................3, 31GB-2 ..................................3

GB-2D ................................3GB-2GD........................3, 31GB-3GD........................3, 31

-H-HL-SJ................................24HPF-54 ............................14HQS-(*) ............................20HRS-(*)G ..........................21HXR-598 ............................4

-K-KI-(*) ..................................8KJ-81(*) ..............................8KJ5E-(*) ..............................8KJ-RJ11 ..............................8KS-KS ................................2KWP-(*) ..............................8

-L-LA-595 ..............................29LA-917 ..............................39LA-917D............................39LA-9520 ............................39LA-9520D..........................39LEV-2................................41LNC-16/16R(*) ..................37LNC-34 ............................36LNC-38UP ........................37LT-1 ....................................6

-M-MCT-(*) ........................4, 32MDA-18R ............................9MDA-31R ............................9MDA-32R ............................9MDA-34R ............................9MDA-38R ............................9MDX-1 ..............................14MSV-34A ..........................37MT-75 ..............................24MT-75P ............................24

-N-NW......................................3

-P-PDS-34M ..........................36PDS-34X ..........................36PDS-38X ..........................36PDT-1 ..........................4, 32PF-59 ..................................2PI-10 ..........................28, 29PIN-500 ..............................2PS-1..................................29PS-2D ..............................29PS-3..................................29PS-32................................29PS-6,7,8,9,10,11 ..............29PS-62................................29PS-6M ..............................29PS-82................................29

PT-1 ....................................6-R-RCA-59 ..............................2RCA-81 ..............................2RFDM-1 ............................10RFDM-3 ............................10RFDM-10/100/200/300......11RFM-1 ..............................12RTV-3................................31

-S-SAT-(*) ..........................1, 30SB-(*) ............................5, 30SCS-1 ..............................35SCS-1P ............................35SCS-2 ..............................35SCS-33A ..........................13SCS-33DC ........................13SCS-4TG ..........................35SCS-5WP ........................35SCS-6PR ..........................35SF-90 ................................41SF-95 ................................41SF-99 ................................41SF-1000 ............................41SG-10 ..............................31SHA-30UP ........................39SP-(*) ................................15SP-(*)G ............................17SS-1T..................................6SS-2S ................................6SS-3L................................14SSP-(*)..............................33SSP-(*)DC ........................33SSP-(*)DS ........................33STP-12D ..........................40STR-(*)..........................4, 30SWP-10 ..............................7

-T-TAP-1 ................................24TDA-2 ..............................32TG2G-(*) ..........................34TGV-(*) ............................22TGS-(*)G ..........................19TLC-7/15/25......................32TMA-1 ..............................32TMC-3 ..........................32TMP-4F ........................32TMP-8F ........................32TRM-1 ............................2TV2G-6/8......................34

-U-UV-SJ ..........................24

-V-VBC..........................1, 30

INDEX

ITEM# PAGE ITEM# PAGE ITEM# PAGE ITEM# PAGE


TERMS AND CONDITIONS

PRICES: Subject to change without notice. Prices do not include freight or shipping charges, unless specified.

MINIMUM ORDER: $250.00 minimum order on purchases. A $10.00 service charge will be added to orders under $250.00. Orders under$100.00 will not be accepted.

TERMS: Net 30 terms apply to approved accounts. All other accounts will be C.O.D., Prepay or Wire Transfer. Private label customers: 30%deposit with order, and balance prepayed before shipment. International Customers: Prepayment or C.O.D.

PAST DUE ACCOUNTS: All accounts over 60 days past due will be shipped C.O.D. ONLY. Accounts over 90 days will be notified andturned over for collection 10 days after notification.

COLLECTION: Customer is responsible for any costs or fees necessary to collect past due accounts.

FINANCE CHARGE: Finance Charge of 1.5% per month will be applied to all invoices over 30 days.

RETURNED CHECK CHARGES: A $25.00 returned check fee will be charged to customers for each time a check is returned.

FREIGHT: F.O.B. shipping point. Loss or damage in transit must be filed with carrier within 10 days.

SHORTAGES: ASKA Communication Corp must be notified of any shortages within 10 days from invoice date.

REPAIR/RETURN MERCHANDISE: Customers must have a “Return Merchandise Authorization” number (RMA) which can be obtainedby telephone or in writing. Product may be repaired, replaced, or credited at our option. Original invoice number; quantity, item number,description and reason for return are required to issue RMA. Any return merchandise is to be sent back freight prepaid. Merchandise beingreturned for credit must done within 30 days from date of purchase, restocking charges may apply. Merchandise and packaging materials must bein original factory condition.

NO REFUNDS WITH OUT SALES RECEIPTS: Equipment must be inspected by ASKA Communication Corp before any decision is madeon refunds. Most sales are final. No refunds on any items after 30 days, credit only.

SPECIAL ORDER ITEMS: Special order items are non-returnable. Special order items must be paid in full upon ordering.

BANK WIRE INFORMATION:WIRE TO: Bank of America Account Name:ASKA Communication Corp.

Business Banking-Palm Beach 2911 Center port circle625 N. Flagler Drive Pompano Beach, Florida 33064 USAWest Palm Beach, Florida 33401

Account Number: 003601974584 ABA Number: 063100277

BROKEN PACK QUANTITY: All broken pack quantities will incur a 5% surcharge.BACK ORDERS: Any out of stock items at special pricing will not be back ordered.

LIMITED 1 (ONE) YEAR WARRANTY:

ASKA Communication Corp extends a Limited 1 (One) Year Warranty on its equipment against manufacture defect and workmanship undernormal use and service. ASKA Communication Corp at its option will repair, replace or refund the purchase price of the item returned. Removalor replacement of equipment and its transportation shall not be at the cost of ASKA Communication Corp except ASKA Communication Corpshall return repaired or replaced equipment freight prepaid.

This Warranty shall not apply to equipment which has been repaired or altered in any way so as to affect its stability or durability, nor which hasbeen subject to misuse, negligence or accident. This Warranty does not cover equipment which has been impaired by severe weather conditionssuch as excessive wind, ice, storms, lightning, or other natural occurrences over which ASKA Communication Corp has no control, nor shall thisWarranty apply to equipment which has been operated or installed other than in accordance with the instructions furnished by ASKACommunication Corp.

Claimants under this Warranty shall present their claim along with the defective equipment to ASKA Communication Corp immediately uponfailure. Non-compliance with any part of this claim procedure may invalidate this warranty in whole or in part.

THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER AGREEMENTS AND WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. ASKA COMMUNICATION CORP DOES NOT AUTHORIZE ANY PERSON TO

ASSUME FOR IT THE OBLIGATIONS CONTAINED IN THIS WARRANTY AND ASKA COMMUNICATION CORP NEITHER ASSUMES NOR AUTHORIZES ANY

REPRESENTATIVE OR OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITIES IN CONNECTION WITH THE EQUIPMENT DELIVERED OR PROVIDED.

IN NO EVENT SHALL ASKA COMMUNICATION CORP BE LIABLE FOR ANY LOSS OF PROFITS, LOSS OF USE, INTERRUPTION OF BUSINESS, OR INDIRECT, SPECIAL

OF CONSEQUENTIAL DAMAGES OF ANY KIND.

In no event shall ASKA Communication Corp be liable for damages in an amount greater than the purchase price of the equipment.

W ARRANTY INFORMATION

Catalogo Aska

Documents

Transcript of Catalogo Aska