CAT6 PATCH PANEL MODULE - cdlnz.com
2
www.dynamix.co.nz | www.dynamix.net.au CAT6 PATCH PANEL MODULE CODE: HPP-1008-1SL The Patch Panel provides a network interface for local area network applications such as ISDN or DSL services and supports Cat6 performance. This module has eight 4x pairs 110 IDC connectors and each of them connects to an individual RJ45 jack. The Ethernet Hub can be linked using a patch lead for high-speed network application. 1. Place the module horizontally. 2. Push the module so the hook and tabs fall into the rail slots of the enclosure. 3. Slide the module LEFT and the spring fastener will automatically lock the module at the desired position. Terminate the cables on the 4x pairs 110 connectors of the data distribution module. Each Cat6 cable should be fully terminated on the contact blades. This module supports TIA T568A wiring standard and is capable of connecting 8x Cat6 cables. Identify which, port you want activated and connect one end of a patch lead to the corresponding jack and the other end to the Ethernet Hub. Features Instructions Operations 1. Push 2. Slide 3. Top View Tabs Hook Spring Fastener • Supports Cat6 performance • 8x 4 pair 110 IDC connectors • Dimensions: 48 x 157 x 21mm • 1 Year warranty
Transcript of CAT6 PATCH PANEL MODULE - cdlnz.com
www.dynamix.co.nz | www.dynamix.net.au
CAT6 PATCH PANEL MODULECODE: HPP-1008-1SL
The Patch Panel provides a network interface for local area network applications such as ISDN or DSL services and supports Cat6 performance. This module has eight 4x pairs 110 IDC connectors and each of them connects to an individual RJ45 jack. The Ethernet Hub can be linked using a patch lead for high-speed network application.
1. Place the module horizontally.2. Push the module so the hook and tabs fall into the rail slots of the enclosure.3. Slide the module LEFT and the spring fastener will automatically lock the module at the desired position.
Terminate the cables on the 4x pairs 110 connectors of the data distribution module. Each Cat6 cable should be fully terminated on the contact blades. This module supports TIA T568A wiring standard and is capable of connecting 8x Cat6 cables. Identify which, port you want activated and connect one end of a patch lead to the corresponding jack and the other end to the Ethernet Hub.
Features
Instructions
Operations
1.
Push
2.
Slide
3.
Top ViewTabs Hook
Spring Fastener
• Supports Cat6 performance• 8x 4 pair 110 IDC connectors• Dimensions: 48 x 157 x 21mm• 1 Year warranty
www.dynamix.co.nz | www.dynamix.net.au
PATCH PANEL MODULECODE: HPP-1008-1SL
1 3 5 7
2 4 6 8
1 2 3 4 5 6 7 8
FROM LOCATION
TO HUB
ETHERNET HUB
DC 12V
ADSL MODEM
ETHERNET HUB
DC 12V
WALL OUTLET
FROM LOCATION
FROM LOCATION
1 2 3 4 5 6 7 8
For 110 IDC connector, follow the wire colour-code and only use 110 punch down tool to push the wire between the contact blades. For RJ45 plug, follow the standard TIA T568B standard for wiring instructions.
1. Strip 5cm of cable jacket.2. Untwist about 10mm of wire and keep jack close to 110 connector.3. According to the colour code, use only a 110 punch down tool to push the wire between the contact blades. The wire may be damaged if another tool is used.
Wire Installation Wiring a 110 Connector
Solid Colour
Brown/WhiteBrown
GreenGreen/White
OrangeOrange/White
BlueBlue/White
Punch Down Tool
kcaJ54-JRgniriW
Pair 1
Pair 4
Pair 3
Pair 2
White/Blue T1
White/Orange T2
Orange R2
White/Green T3
Green R3
White/Brown T4
Brown R4
Blue R1
Band-StripedTwisted Pair Wire
Band Colour
Base Colour
Green
Red
Black
Yellow
White
Blue
Twisted Pair Wire
Wiring a 110 Connector
![HIGH POWER - Veracity...RJ45 Cat6, Cat5e, Patch wiring recommended, other wiring auto-corrected 200Mbps (100Mbps full duplex) up to 820 metres [2,690ft] (Cat6) RJ45 Patch or crossover,](https://static.fdocuments.in/doc/165x107/60f29546fac9192d56608d5b/high-power-veracity-rj45-cat6-cat5e-patch-wiring-recommended-other-wiring.jpg)
