Carter Variator Cat

8/13/2019 Carter Variator Cat

1/40

Superior Gear Technology

Hydrostatic Variable Speed Drives

Carter Variator

www.renold.com


2/40

2

www.renold.com

Carter Variator - Hydrostatic Variable Speed Drivers

2

Totally enclosed and self contained for use inunfavourable environmental conditions dusty,dirty or wet areas , hot or cold ambienttemperatures and hazardous atmospheres.

Full rated torque availableover the entire speed rangeand capable of transmittingup to 200% full rated torqueat start up.

Control setting infinitely adjustable withdrive running or stationary and in builtdynamic braking , important for many

processes and essential whereheavy inertia loads require controlled

acceleration and/or deceleration.

Close speed holdingcharacteristics even under

varying load conditions.

Infinitely variable outputspeed over a 27:1 range.


3/40

Contents

www.renold.com

3

Page No

CARTER VARIATOR FEATURES 2

ATEX APPROVAL DETAILS 4

PRODUCT FEATURES 5

TECHNICAL NOTES 6

SELECTION AND INSTALLATION 7

SELECTION NOTE FOR RENOLD CARTER VARIATOR AND COMBINED

CARTER VARIATOR/ RS SERIES SPEED REDUCER 12

RATINGS TABLE: RENOLD CARTER VARIATOR 13

DIMENSIONS: RENOLD CARTER VARIATOR 15

PRELIMINARY RATING GUIDE: COMBINED RENOLD CARTER VARIATOR

/RENOLD RS SERIES SPEED REDUCER 20

RATINGS TABLES: COMBINED RENOLD CARTER VARIATOR/

RENOLD RS SERIES SPEED REDUCER 21

DIMENSIONS: COMBINED RENOLD CARTER VARIATOR/RENOLD

RS SERIES SPEED REDUCER 29

PERMISSIBLE SHAFT LOADS 30

SPEED CONTROLS 31

OVERLOAD PROTECTION 37

WORLDWIDE SALES & SERVICE 40


4/40

www.renold.com

4

ATEX Approval

Gears products for operating in potentially explosive

atmospheres.

General

Gears units are classified as ATEX Group II Category2 equipment, which embodies sufficient safeguards to besuitable for use in potentially explosive atmospheres for normaloperation and for operation during an expected malfunction.

It is essential that there is sufficient lubricant to prevent thegears and bearings running dry. Gear units should be inspecteddaily for signs of oil leakage, overheating or noisy operation.

Gear units should be cleaned at regular intervals depending onthe operating conditions, to ensure that dust coatings neverexceed 5mm. Plastic parts should be wiped clean with a dampcloth.

Oil leaks should be dealt with as quickly as practical. Compoundjoint faces and shims should be cleaned and thread-lockingsealant should be applied to bolts and plugs prior to re-assembly.

The temperature of any external surfaces must not exceed thepermitted maximum of 135C (T4).

Higher temperature class T3 is available dependant on unitmounting, ratio and gear type. For further details consultRenold.

As a general rule, gear units should be mounted with their feethorizontal. For other mountings, particularly with shaft mounted

units, consult Gears.

WARNING: IF MOUNTING WITH VERTICAL INPUT OR OUTPUTSHAFTS, THE ATEX CERTIFICATION DOES NOT APPLY.

Unit Selection

The gear unit selection procedures must include an additionalreliability factor of 1.25 for mechanical ratings and 1.25 forthermal ratings.

ATEX Nameplate

ATEX APPROVAL DETAILS


5/40

INTRODUCTION

With a depth of experience stretchingback over 100 years, no one under-

stands better than Renold Gears thathostile and hazardous environmentsmake exceptional demands on powertransmission equipment.

The Renold Carter range of Variators arerobust, totally enclosed and superblyqualified to cope with extremes like hightemperatures, wet and dirty workingconditions and explosive atmospheres.

The MKF4 and 5 have been added to therange of MK Variators and thesefacilitate the direct mounting of standard

D flange motors, which results in a morecompact unit.

With a bolt-on IEC output flange the MKrange of Variators allows directinterfacing to any reduction gear thataccepts a standard D flange motor.

Renold Carter Variators give smooth,stepless speed variations over a 27:1speed range and provide 200% full

rated torque on start up. Superbreliability goes hand-in-hand withminimum maintenance. A periodic oilchange is all that is needed. Many arestill working perfectly after thirty years.

Even so, we still offer a 24-hourreplacement service of factory-refurbished units, each covered by a1-year guarantee.

The full Renold Carter range of 11variators will accommodate the fullspectrum of control options:mechanical, pneumatic, electric orelectronic.

Coming from Renold Gears, the fullrange also benefits from the latest

CAD/CAM technology that ensures ourdesign and production facilities areamong the most advanced in theindustry.

Naturally, this sophisticated technology isalso used by our design and applicationsengineers, to help them to help youselect exactly the right unit for yourparticular application.

www.renold.com

5


6/40

www.renold.com

6


7/40

www.renold.com

7


8/40

www.renold.com

8


9/40

www.renold.com

9


10/40

www.renold.com

10


11/40

www.renold.com

11

Units to ATEX approval must be selectedwith a minimum service factor of 1.25.


12/40

www.renold.com

12

Units to ATEX approval must be selected

with a minimum service factor of 1.25.


13/40

www.renold.com

13


14/40

www.renold.com

14




15/40

www.renold.com

15


16/40

www.renold.com

16


17/40

www.renold.com

17


18/40

www.renold.com

18


19/40

www.renold.com

19


20/40

www.renold.com

20




21/40

www.renold.com

21


22/40

www.renold.com

22


23/40

www.renold.com

23


24/40

www.renold.com

24


25/40

www.renold.com

25


26/40

www.renold.com

26


27/40

www.renold.com

27

MK & MKF BASIC CARTER VARIATOR

WITH RS SERIES SPEED REDUCER


28/40

www.renold.com

28


29/40

www.renold.com

29

SHAFT AND KEYWAY DIMENSIONS

Keys supplied

32k6 80 5 70 10P9 27.00/26.8 8 M12 28

38k6 80 5 70 10P9 33.00/32.8 8 M12 28

55m6 110 5 100 16P9 49.00/48.8 10 M20 42

RS SeriesSize

GM3D

GM4T

GM6D

S

mm

T

mm

U

mm

V

mm

W

mm

X

mm

XD

mm

Y

mm

Z

mm

DIMENSIONS: COMBINED RENOLD CARTERVARIATOR/RENOLD RS SERIES SPEED REDUCER -CARTER VARIATOR MA

GM3D 227 12 106 81 60 170 115 38.5 50 333 190.4 150 275 44.3

GM4T 273 14 118 91 60 218 120 40.5 65 391 190.4 150 305 58.4

GM3D 252 12 106 81 60 191.5 115 60.6 50 358 212.6 150 275 55.5

GM4T 298.5 14 118 91 60 240 120 62.6 65 416.5 212.6 150 305 65.4

GM3D 251 20.6 106 81 75 174 171 25 70 359 253.9 150 395 53

GM4T 302 20.6 118 91 75 225 186 25 70 420 253.9 150 425 75

GM6D 315 22 155 125 60 253 167.5 35 75 470 225 200 390 113

GM6D 347 22 155 125 60 285 167.5 35 75 502 225 200 390 125

GM6D 372 22 155 125 60 305 167.5 35 75 527 225 200 390 127

CarterVariator

Size

RS SeriesSize

MA3

MA4

MA26

MA5

MA6

MA42

A

mm

C

mm

D

mm

E

mm

F

mm

G

mm

H

mm

J

mm

K

mm

L

mm

M

mm

N

mm

P

mm

Weight(mass)approx

Kg

MA VARIATORS

CARTER VARIATOR WITH RS SERIES SPEED REDUCER

J M

N

EKK

FGH H

AP D

L

2 HOLES CDIAMETER

X

S

X DW

T

Z

V U

Y


30/40

www.renold.com

30


31/40

www.renold.com

31


32/40

www.renold.com

32


33/40

www.renold.com

33

For use

with

Carter

Variator

MK01 8.7

8.7 127.5

127.5

127.5

127.5

127.5

8.7

12.7

14.5

17.5

127.5 88.5

88.5

121

149.5

207

241.5

108

118

103

135.5

124

122

187

187

180

192

202

214

225

225

235

276

293

325

196.5

206.5

224

285

331

363.5

119

119

129

169

187

219

MK02

MF10

MKF3

MKF4

MKF5

Amm

Bmm

Cmm

Dmm

Emm

Fmm

Gmm

Hmm

For use

with

Carter

Variator

MA3 178

178 214

246

284

311

384

178

226

226

226

197 53

62

70

79

95

108

450

472

491

589

627

684

106

106

106

132

132

132

MA4

MA26

MA5

MA6

MA42

Amm

Bmm

Cmm

Dmm

Emm


34/40

www.renold.com

34


35/40

www.renold.com

35

For use

with

Carter

Variator

MK01 196.5

206.5 83.5

83.5

83.5

83.5

83.5

224

285

331

363.5

83.5 67.5

67.5

67.5

67.5

67.5

67.5

108

118

103

135.5

124

122

88.5

88.5

121

207

207

241.3

44.5

44.5

44.5

44.5

44.5

44.5

89

89

89

89

89

89

283

283

262

289

322

341

MK02

MF10

MKF3

MKF4

MKF5

Amm

Bmm

Cmm

Dmm

Emm

Fmm

Gmm

Hmm

For use

with

Carter

Variator

MA3 197

214 62

70

79

95

108

246

284

311

384

53 239

239

239

310

310

404

297

319

338

458.5

458.5

515.5

75

75

75

122

122

122

81

81

81

119

119

119

MA4

MA26

MA5

MA6

MA42

Amm

Bmm

Cmm

Emm

Fmm

Gmm


36/40

www.renold.com

36

ELECTRONIC CONTROLS

The CONTROSET 125 is a versatilemonitor and controller designed anddeveloped for use with standard servo

control motors on Carter HydrostaticVariable Speed Drives.

A four digit LED displays continuousspeed or rate indication in the normal runmode.

The keypad is used to directly select therequired speed and set various controlparameters, such as top and bottomspeed limits, pre-set speeds, manualoverride, and can be arranged toincorporate incoming process signals andlow speed inter-locking features.

Utilising tacho feedback to the controller

via a speed sensing probe fitted to theCarter Variator, provides speed controlaccuracy to +0.1%, even under varyingload.

The CONTROSET 125 can be retrofittedto existing Carter installations, thusproviding enhanced control to the provenreliability of the Carter HydrostaticVariable Speed Drives.

A VARIETY OF CONTROL OPTIONS

Simple direct control of Carter Variatorvia the keypad - on the Controsetcontroller. Automated process control,

the command or feedback signal beingderived from a transducer or computermonitoring the condition of the materialbeing produced. Typical processconditions which can be controlled aretemperature, pressure, weight, moisturecontent, flow etc.Preferred signals 0-10v,0-10 and 4-20mA. The facility to link andcontrol automatically a number of CarterVariators driving individual machinesections. Ratio of speeds between theindividual sections can be achieved byincorporating suitable trimmers to modifythe reference signals.

A simple auto/manual switch option can beincorporated into the control circuit. Thisallows (in the event of loss of a transducersignal or failure in the electronic circuitry)for the control to be switched over to amanual operation of the drive/drives byFAST/SLOW push buttons until it isconvenient to rectify the fault. Thisminimizes down-time and lost production.

ROTARY SPEED CONTROLS -

RENOLD CARTER VARIATOR MK, MKF MF & MA

SPEED INDICATION

DFM100

DIGITAL METER

PROXIMITY

PROBE

SPEED INDICATION

Indication of variator output speed can beprovided on the full range of CarterVariators and is achieved using a DigitalMeter, in conjunction with a ProximityProbe fitted to the Carter Variator whichmonitors its output speed.

DIGITAL METERTwo types are available, the DFM100which is used to indicate speed orprocess rate (meters, revs/min etc) andthe DTM25 which can be calibrated tosuit continuous processes for indicationof baking, freezing, drying times etc.


37/40

www.renold.com

37


38/40

www.renold.com

38

Worldwide Sales and Services

ARGENTINABennett Anderson,Gonzales Y Cia SA, J.Aguero 1817(1605) MunroBuenos Aires

Tel: + 54 11 4761 5007/ 3531Fax: + 54 11 4760 0866

Los Ases Ketten SA,Avda Gaona 4046,1407 Buenos AiresTel: + 54 116710855Fax: + 54 116713141

AUSTRALIARenold Australia Proprietary Ltd508-520 Wellington Road,Mulgrave, Victoria 3170, MulgraveNorthTel: +61 (0) 3 9262 3333Fax: +61 (0) 3 9561 8561Branch Tel: +61 (0) 3 9262 3355Email:[email protected]

Unit 1,12-18 Victoria Street, Lidcombe,Sydney, NSW 2141.Tel: +61 (0) 2 9649 3122Fax: +61 (0) 2 9646 1295Email:[email protected]

Unit 10,31 Boyland Avenue,Coopers Plains, Brisbane,Queensland 4108.Tel: +61 (0) 7 3275 2155Fax: +61 (0) 7 3875 1779

Corner Orsmond & George Sts.Hindmarsh, Adelaide,South Australia 5007.Tel: +61 (0) 8 8346 9077

Fax: +61 (0) 8 8340 1217

Unit 2,127 Grandstand Street, Belmont,Perth, West Australia 6104.Tel: +61 (0) 8 9479 1388Fax: +61 (0) 8 9479 1364

Unit 1356 Industrial Drive,Mayfield, NSW 2304Tel: +61 (0) 2 4960 8440Fax: +61 (0) 2 4960 8455

PO Box 159,Unanderra, Wollongong, NSW 2526.Tel: +61 (0) 2 42 621771Fax: +61 (0) 2 42 621772

Shop B,247 Ingham Road,Garbutt, Townsville, QLD 4814.Tel: +61 (0) 7 4779 5922Fax: +61 (0) 7 4775 1446

AUSTRIARenold GmbHRudolf Hausner Gasse 60/1A-1220 WienAustria.Tel: +43 (0) 1 3303484 0Fax: +43 (0) 1 3303484 5

BANGLADESHBrady & Co (Bangladesh) Ltd,31, Bangabandhu Avenue,Dhaka-1000

Tel: + 880 2802358Fax: + 880 2802358

BELGIUMRenold Continental LtdAlle Verte 1,1000 Brussel.Tel: +32 (0) 2 2011262Fax: +32 (0) 2 2032210

Email: [email protected]

CANADARenold Canada Ltd121 Roy Boulevard, Brantford,Ontario, N3T 5N4Toll Free: 1-800-265-9970Tel: +1 519 756 6118Fax: +1 519 756 1767Email: [email protected]

622 rue De Hull,Ville La Salle,Quebec, H8R 1V9.Toll Free: 1-800-361-1414Tel: +1 514 367 1764Fax: +1 514 367 4993

CHILESargent S.A.,Avda. Presidente Bulnes No 205,Casilla 166-D,Santiago - Chile.Tel: (56 2) 510 3000Fax: (56 2) 698 3989Email: [email protected]

CHINARenold Transmission (Shanghai)Company LimitedUnit 4A, Block 1569 XiYa RoadWaigaoqiao Free Trade ZoneShanghai 200131Tel: +86 21 5046 2696Fax: +86 21 5046 2695Email: [email protected]

COLOMBIATransmission de Potencia SACarrera 68B No10 - 98Apartado Aereo 6794Santafe de Bogato DCTel: + 571 2600100Fax: + 571 2904823

Importadora Casa Sueca Ltda.,Calle 52, No. 1N-74,Apartado Aereo 1208, Cali.Tel: 00 57 2346 4455Fax: 00 57 2346 4967

CZECH REPUBLICRenold GesmbHTechnical Office, Dipl. Ing. R.

Badura,Jaroslavice 129, CZ-76001 Zlin.Tel: +42 67 7211074Fax: +42 67 7211074

DENMARKRenold A/S,Skelmarksvej 6, Postboks 90,2605 Brndby.Tel: +45 43 452611Fax: +45 43 456592Email: [email protected]

EGYPTItaco,Intl for Trading & Agency,P.O. Box 7550, Nasr City, Cairo.Tel: + 20 2 2718036

Fax: + 20 2 2878089

EL SALVADORMVA & CiaResidencial San Luis,Avenida 4 #45 Block 2,San Salvador,

El-Salvador, Central AmericaTel: + 503 274 649

FINLANDKraftmek Oy,Hitsaajankatu 9, P.O. Box 36,FIN-00811 HelsinkiTel: + 358 9 7557355Fax: + 358 9 7550414

FRANCEBrampton Renold,Zone Industrielle A, Rue de laPointe, BP 359, 59473 Seclin Cedex.Tel: +33 (0) 320 16 29 29Fax: +33 (0) 320 16 29 00

GERMANY

Arnold & Stolzenberg,Juliusmhle,D37574 Einbeck.Postal address:PO Box 1635 + 1645D37557 Einbeck.Tel: +49 (0) 5562 81248Fax: +49 (0) 5562 81130Email:[email protected]

GREECEProvatas Engineering53/47 Dragatsaniou St,185 - 45 Piraeus.Tel: + 30 1 4170266Fax + 30 1 4170253

HOLLANDRenold Continental Ltd,Jarmuiden 30c,1046 AD Amsterdam.Tel: +31 (0) 20 614 6661Fax: +31 (0) 20 614 6391Email: [email protected]

HUNGARYRenold GesmbHTechnical Office, Ing. Havasi Janos,Ret Utca 25, H-6200 Kiskrs.Tel: +36 (0) 78 312483Fax: +36 (0) 78 312484

INDIAVoltas Limited.,Machine Tool Division,Voltas House B, 3rd Floor,

TB Kadam Marg,Chinchpokli,Mumbai 400033Tel: 091 22 370 0829Fax: 091 22 371 4889Email:[email protected]

NORTHERN IRELANDHenry R. Ayton Ltd,Derriaghy, Dunmurry, Belfast.Tel: 01232 618511Fax: 01232 602436

SOUTHERN IRELANDHenry R. Ayton Ltd.,Broomhill Drive, Tallagh, Dublin 24Tel: + 353 (0) 1 4517922

Fax: + 353 (0) 1 4517922

ISRAELTechnica J. Bokstein Co. Ltd,3 Hatrupa Street,Netanya 42504Tel: + 972 9 8850505

Fax: + 972 36131074

ITALYBianchi Cuscinetti SpAVia Zuretti, 102, 20125 Milano,Tel: + 39 02 67861Fax: + 39 02 66981669

JAMAICAMasterton Ltd,21-25 Hanover Street, P.O. Box 73Kingston.Tel: + 18 767 540557Fax: + 18 769 227807

KOREAS.S. Corporation,Yeouido, P.O. Box 60, Seoul.

Tel: 00-822-783-6829Fax: 00-822-784-9322Email: [email protected]

MALAYSIARenold (Malaysia)LOT 2, Jalan Kecapi 33/2,Eilte Industrial Park,Off Jalan Bukit, Kemuning,40400 Shah Alam, Selangor,Malaysia.Tel: + 60 3 5122 9880Fax: + 60 3 5191 9881Email:[email protected]

201, Jalan Simbang,Taman Perling,81200 Joho Bharu, Johor, Malaysia.

Tel: + 60 (0) 7 2384152-3Fax: + 60 (0) 7 2384155Email:[email protected]

67A, Jalan Medan Ipoh 6,Bandar Baru Medan,31400 Ipoh, PerakTel: + 60 (0) 5 548 0059Fax: + 60 (0) 5 548 0214Email:[email protected]

28B Jalan Perai Jaya 3,Bandar Perai Jaya,13600 Perai,Penang, MalaysiaTel: + 604-399 9648Tel: + 604-399 0648Fax: + 604-399 5649Email:[email protected]

MAURITIUSDynamotors Ltd,P.O. Box 733, Bell Village,Tel: + 230 2122847/8/9Fax: + 230 2088348

MEXICOAccessorios Automotrices yRodamientos Industriales,S.A. de C.V., Calz Legaria 833-ACol Irigacion, Mexico DF 11500Tel: + 52 5 395 6300Fax: + 52 5 395 6370


39/40

www.renold.com

39

Worldwide Sales and Services

NEW ZEALANDRenold New Zealand,594 Rosebank Road,Avondale, Auckland.

Postal Address:PO Box 19460,Avondale, Auckland.Tel: + 64 (0) 9 828 5018Fax: + 64 (0) 9 828 5019Email:[email protected]

Christchurch Branch Office,32 Birmingham Drive, Christchurch,PO Box 9006, Christchurch,Tel: + 64 03 338 2169Fax: + 64 03 338 8663

NORWAYG. Heier A/S,Postal Address: Postboks 6615,Rodelokka, 0502 Oslo, Norway.Office Address: Thv, Meyersgt.

7, Oslo.Tel: + 47 232 34230Fax: + 47 232 34242

PAKISTANBrady & Co. of Pakistan Ltd,Shernaz House, P.O. Box 4453,West Wharf Road, Karachi 2.Tel: + 92 21.2310367/201712Fax: + 92 21.2313376/2313378

PERUCorporacion Basco S.A.C.Av. Argentina 1165,Lima 1, RUC 25776186.Tel: + 51 1 4336633Fax: + 51 1 4313188

PORTUGALHarker, Sumner, S.A.Zona Industrial Maia 1 - Sector X4475 - 132 Gemunde - MaiaPortugal.Tel: + 351 229 4478 090Fax: + 351 229 4478 098E-mail: [email protected]

SINGAPORERenold Transmission Limited63 Hillview Avenue, #07-13,Lam Soon Industrial Building,Singapore 669569.Tel: + 65 6760 2422Fax: + 65 6760 1507E-mail: [email protected]

SOUTH AFRICARenold Croft (Pty) Limited,Corner Liverpool and Bolton Streets,Nestadt Industrial Sites, Benoni, 1501Postal Address: Private Bag x 030,

Benoni, 1500.Tel: + 27 (0) 11 747 9500Fax: + 27 (0) 11 747 9505E-mail: [email protected]

P.O. Box 2661, Witbank 1035,Mpumalanga,Republic of South Africa.Tel: +27 (0) 13 692 7760Fax: +27 (0) 13 697 0546Email: [email protected]

SPAINBrown Pestell,Ctra N-11 Lm. 599.5 Nave 5,08780 Palleja, Barcelona.Tel: + 34 93 6630740Fax: + 34 93 6632057

SWEDENRenold A/SSkelmarksvej 6, Postboks 902605 BrndbyDenmark.Tel: + 45 43 452611Fax: + 45 43 456592E-mail: [email protected]

SWITZERLANDRenold (Switzerland) Gmbh,Ringstrasse 16, Postfach 1115CH-8600 Dbendorf 1.Tel: + 41 (0) 1 824 8484Fax: + 41 (0) 1 824 8411E-mail: [email protected]

Route De Prilly 25,CH-1023 Crissier.Tel: + 41 (0) 21 632 9460Fax: + 41 (0) 21 632 9475E-mail: [email protected]

THAILANDUnited Power Engineering Co Ltd4 Soi Sukhumvit 81 (Siripot)Sukhumvit RoadBangjak, PhrakhanongBangkok 10260.Tel: + 66 2 7425366Fax: + 66 2 7425379

TRINIDADTracmac Engineering Ltd,P.O. Box 945, Port of Spain,Trinidad, West Indies.

Tel: + 1 665 460 1532Fax: + 1 868 671 0012

TURKEYGlengo Ithalat lhracat MumessillikAS,Gungoren Cad. No. 35 Bagcilar,34560

Bakirkoy, Istanbul.Tel: + 90 212 4613970Fax: + 90 212 4613972www.glengo.com.tr

UNITED KINGDOMRenold GearsHolroyd Gears Works, Milnrow,Rochdale OL16 3LSTel: +44 (0) 1706 751000Fax: +44 (0) 1706 751001E-mail: [email protected]: www.renold.com

Renold Clutches & CouplingsWentloog Corporate Park,Newlands Road,Cardiff CF3 2EU, Wales

Tel: + 44 (0) 29 20792737Fax: + 44 (0) 29 20793004(Sales):+ 44 (0) 29 20791360E-mail: [email protected]: www.renold.com

Renold Hi-Tec Couplings112 Parkinson RoadHalifax HX1 3QHTel: +44 (0) 1422 255000Fax: +44 (0) 1422 320273E-mail: [email protected]: www.renold.com

HolroydHarbour Lane North, Milnrow,Rochdale, OL16 3LQ.Tel: +44 (0) 1706 526 590Fax: +44 (0) 1706 353 350

E-mail: [email protected]: www.holroyd.com

Renold ChainUK Sales, Horninglow Road,Burton upon Trent,Staffordshire, DE14 2PS.Tel: +44 (0) 1283 512 940Fax: +44 (0) 1283 512 628E-mail: [email protected]

USARenold IncBourne Street, PO Box A, Westfield,New York, 14787-0546Tel: + 1 716 326 3121

Fax: + 1 716 326 6121E-mail: [email protected]

VENEZUELAEquipos Y Acessorios Astral CA,Apartado 1651 Valencia.Tel: + 584 1 332042Fax: + 584 1 345641

WEBwww.renold.com

Terms and Conditions In the interests of safety, customers are reminded that when purchasing anytechnical product for use at work (or otherwise), any additional or up-to-dateinformation and guidance, which it has not been possible to include in thepublication, should be obtained by you from your local sales office in relation tothe suitability and the safe and proper use of the product. All relevant informationand guidance must be passed on by you to the person engaged in, or likely to beaffected by or responsible for the use of the product

The performance levels and tolerances of our product stated in this catalogue(including without limitation, serviceability, wearlife, resistance to fatigue,corrosion protection) have been verified in a programme of testing and qualitycontrol in accordance with Renold, independent and/or international standard

recommendations. No representations or warranties are given that our productshall meet the stated performance levels or tolerances for any given applicationoutside the performance levels and tolerances for the products own specificapplication and environment.

Whilst all reasonable care in compiling the information contained in thiscatalogue is taken, no responsibility is accepted for errors.

All information contained in this catalogue is subject to change without notice.

The illustrations used in this catalogue represent the type of product describedbut the goods supplied may vary in some detail from those illustrated.

The right is reserved to make modifications to the product to meetmanufacturing conditions and/or developments (for example in design ormaterials).

Product can be supplied by Renold companies or representatives around theworld on the standard terms and conditions of sale of the company or

representative from which the product is purchased. Copyright Renold Power Transmission Limited 2001. All rights reserved.

Nothing contained in this publication shall constitute a part of any contract,express or implied.


40/40

AUSTRALIA

Melbourne (Victoria)Tel + 61 (03) 9262 3333Fax + 61 (03) 9561 8561also at: Sydney, Brisbane, Adelaide, Perth,

Newcastle, Wollongong, Townsville.

AUSTRIA

ViennaTel + 43 (0) 13303484-0Fax + 43 (0) 13303484-5also at: Kiskrs (Hungary), Jaroslavice(Czech Republic).

BELGIUM

BrusselsTel + 32 (0) 2 201 1262Fax + 32 (0) 2 203 2210

CANADA

Brantford (Ontario)Tel + 1 519 756 6118Fax + 1 519 756 1767also at: Montreal.

CHINA

ShanghaiTel + 21 5046 2696Fax + 21 5046 2695

DENMARK

Brndby (Copenhagen)

Tel + 45 43 45 26 11Fax + 45 43 45 65 92

FRANCE

SeclinTel + 33 (0) 320 16 29 29Fax + 33 (0) 320 16 29 00

GERMANY

EinbeckTel + 49 (0) 5562 81248Fax +49 (0) 5562 81130also at: Hamburg, Bielefeld, Dsseldorf,

Frankfurt, Kornwestheim, Berlin.

KOREA

SeoulTel + 822 783 6829Fax +822 784 9322

MALAYSIA

Selangor Darul EhsanTel + 60 3-5191 9880Fax + 60 3-5191 9881also at: Johor Bharu, Ipoh, Penang.

NETHERLANDS

AmsterdamTel + 31 206 146661Fax + 31 206 146391

NEW ZEALAND

AucklandTel + 64 9 828 5018Fax + 64 9 828 5019also at: Christchurch.

SINGAPORE

SingaporeTel + 65 6760 2422

Fax + 65 6760 1507

SOUTH AFRICA

BenoniTel + 27 11 747 9500Fax + 27 11 747 9505also at: Witbank.

SWEDEN

Brndby (Copenhagen)Tel + 45 43 45 26 11Fax + 45 43 45 65 92

SWITZERLANDDbendorf (Zrich)Tel + 41 (1) 824 8484Tel + 41 (1) 824 8411also at: Crissier (Lausanne).

UK

Renold Gears, RochdaleTel + 44 (0) 1706 751000Fax + 44 (0) 1706 751001e-mail : [email protected]

USA

Westfield NYTel + 1 716 326 3121Fax + 1 716 326 6121

WEB

www.renold.com

E-MAIL

e-mail : [email protected]

For other country distributorsplease contact Renold UK.

Carter Variator Cat

Documents

Transcript of Carter Variator Cat