CAPSULES, END CAPS and THREE-WAYS JOINTS · POLISHED, SUPER POLISHED AND SATINED STAINLESS STEEL...
1
57 CPJQTAC/S 045/... CPJQTACML 045/... IPJQTAC/S 045/... IPJQTACML 045/... TPJQTAC/S 045/... GIJQT 045/... * * * * * * PROJOLLY QUART POLISHED, SUPER POLISHED AND SATIN FINISH STAINLESS STEEL AISI 304/1.4301-V2A PROJOLLY ANODIZED, POLISHED AND BRUSHED ALUMINIUM PROJOLLY QUART is a quarter-circle rounded bead profile in polished, super polished and satin finish stainless steel AISI 304/1.4301-V2A that can be applied on external corners of coverings. It can be used to close the perimeter of coverings and like a connection profile between step tread and riser of stairs coated with ceramic or natural stone tiles. Its particular section, the availability in three different finishes and special pieces such as internal and external corners, end caps and joints make PROJOLLY QUART a much sought-after profile that allows a workmanlike application even in environments subject to high mechanical stresses. PROJOLLY is a rounded bead profile in anodized aluminium that can be applied on external corners of coverings. It can be used to close the perimeter of coverings and like a connection profile between step tread and riser of stairs coated with ceramic or natural stone tiles. Its particular section and elegance, the availability in seven different finishes and special pieces such as internal and external corners, end caps and joints make PROJOLLY a much sought-after and elegant profile that allows a workmanlike application. PJQTAC/S 045 PJQTACML 045 EXTERNAL CAPSULES INTERNAL CAPSULES END CAP JOINT EXAMPLES AND INSTRUCTIONS FOR LAYING METHODS 1. Choose “PROJOLLY QUART” according to the tile thickness and desired finish. 2. Cut “PROJOLLY QUART to the desired length and apply the adhesive on the support where the profile will be laid. 3. Press the anchoring flange of “PROJOLLY QUART” into the adhesive. 4. Lay the tiles, aligning them with the profile leaving a 2 mm joint. Remove immediately all remains of adhesive from the surface of the profile. 5. Fill the joints between the profile and the tiles with grout, in order to avoid water stagnation. Remove immediately all the remains of grout from the surface of the profile. CAPSULES and END CAPS -POLISHED STAINLESS STEEL AISI 304/1.4301-V2A JOINTS - PLASTIC POLISHED STAINLESS STEEL AISI 304/1.4301-V2A with protective film bar length 2,7 lm - pack. 30 Pcs - 10/10mm Article H mm CPJQTAC 045/... (external) 4,5 IPJQTAC 045/... (internal) 4,5 TPJQTAC 045/... (end cap) 4,5 Article H mm GIJQT 045/... 4,5 CAPSULES and END CAPS - SATINED STAINLESS ST. AISI 304/1.4301-V2A Article H mm CPJQTACS 045/... (external) 4,5 IPJQTACS 045/... (internal) 4,5 TPJQTACS 045/... (end cap) 4,5 CAPSULES SUPER POLISHED STAINLESS STEEL AISI 304/1.4301-V2A Article H mm CPJQTACML 045/... (external) 4,5 IPJQTACML 045/... (internal) 4,5 SUPER POLISHED STAINLESS STEEL AISI 304/1.4301-V2A thermo packed bar length 2,7 lm - pack. 30 Pcs 81 lm - 10/10mm SATINED STAINLESS STEEL AISI 304/1.4301-V2A with protective film bar length 2,7 lm - pack. 30 Pcs - 81 lm - 10/10mm Choose the desired packaging. E.g.: CPJQTAC .../10 (Pack. 10 Pcs) CPJQTAC .../2 (Pack. 2 Pcs) Choose the desired packaging. E.g.: CPJQTACML .../10 (Pack. 10 Pcs) CPJQTACML .../2 (Pack. 2 Pcs) Choose the desired packaging. E.g.: CPJQTACS .../10 (Pack. 10 Pcs) CPJQTACS .../2 (Pack. 2 Pcs) Choose the desired packaging. E.g.: GIJQT .../10 (Pack. 10 Pcs) GIJQT .../2 (Pack. 2 Pcs) SUITABLE FOR USE IN CONTACT WITH FOODSTUFFS. H 4,5 mm profiles for low thicknesses PJ... 03 PJ... 045 EXAMPLES AND INSTRUCTIONS FOR LAYING METHODS 1. Choose “PROJOLLY” according to the tile thickness and desired finish. 2. Cut “PROJOLLY” to the desired length and apply the adhesive on the support where the profile will be laid. 3. Press the anchoring flange of “PROJOLLY” into the adhesive. 4. Lay the tiles, aligning them with the profile leaving a 2 mm joint. Remove immediately all remains of adhesive from the surface of the profile. 5. Fill the joints between the profile and the tiles with grout, in order to avoid water stagnation. Remove immediately all the remains of grout from the surface of the profile. POLISHED ALUMINIUM (chrome- gold) thermo packed bar length 2,7 lm - pack. 40 Pcs - 108 lm POLISHED BRUSHED ALUMINIUM (silver-copper-titanium) thermo packed bar length 2,7 lm - pack. 40 Pcs - 108 lm Article H mm PJBC 03 (polished chrome) 3 PJBO 03 (polished gold) 3 PJBC 045 (polished chrome) 4,5 PJBO 045 (polished gold) 4,5 PJBC 06 (polished chrome) 6 PJBO 06 (polished gold) 6 ANODISED ALUM. (silver-gold) thermo packed bar length 2,7 lm - pack. 40 Pcs - 108 lm Article H mm PJAA 03 (anodised silver) 3 PJAO 03 (anodised gold) 3 PJAA 045 (anodised silver) 4,5 PJAO 045 (anodised gold) 4,5 PJAA 06 (anodised silver) 6 PJAO 06 (anodised gold) 6 Article H mm PJBS 03 (brushed silver) 3 PJRS 03 (brushed copper) 3 PJTS 03 (brushed titanium) 3 PJBS 045 (brushed silver) 4,5 PJRS 045 (brushed copper) 4,5 PJTS 045 (brushed titanium) 4,5 H 3 mm H 4,5 mm PJ... 06 H 6 mm Article H mm PJQTAC 045 (81 LM) 4,5 PJQTAC 06 (54 LM) 6 Article H mm PJQTACML 045 4,5 PJQTACML 06 6 Article H mm PJQTACS 045 4,5 PJQTACS 06 6 PJQTAC/S 06 H 6 mm profiles for low thicknesses COLOURS AC- Polished stainless st. AISI 304/1.4301-V2A ACML - Super polished stainless st. AISI 304/1.4301-V2A ACS - Satin finish stainless st. AISI 304/1.4301-V2A POLISHED, SUPER POLISHED AND SATINED STAINLESS STEEL AISI 304/1.4301-V2A / PLASTIC CAPSULES, END CAPS and THREE-WAYS JOINTS COLOURS ANODIZED POLISHED BRUSHED POLISHED AA- Anodised silver alum. AO - Anod. gold alum. BC- Polished chrome alum. BO - Polished gold alum. BS - Brushed polished silver aluminium RS - Brushed copper alu. TS - Brushed polished titanium alum. = On demand, price and delivery time to be agreed.
Transcript of CAPSULES, END CAPS and THREE-WAYS JOINTS · POLISHED, SUPER POLISHED AND SATINED STAINLESS STEEL...
57
2017
CPJQTAC/S 045/...CPJQTACML 045/...
IPJQTAC/S 045/...IPJQTACML 045/...
TPJQTAC/S 045/... GIJQT 045/...
**
**
**
PROJOLLY QUART
POLISHED, SUPER POLISHED AND SATIN FINISH STAINLESS STEEL AISI 304/1.4301-V2A
PROJOLLYANODIZED, POLISHED AND
BRUSHED ALUMINIUM
PROJOLLY QUART is a quarter-circle rounded bead profile in polished, super polished and satin finish stainless steel AISI 304/1.4301-V2A that can be applied on external corners of coverings. It can be used to close the perimeter of coverings and like a connection profile between step tread and riser of stairs coated with ceramic or natural stone tiles. Its particular section, the availability in three different finishes and special pieces such as internal and external corners, end caps and joints make PROJOLLY QUART a much sought-after profile that allows a workmanlike application even in environments subject to high mechanical stresses.
PROJOLLY is a rounded bead profile in anodized aluminium that can be applied on external corners of coverings. It can be used to close the perimeter of coverings and like a connection profile between step tread and riser of stairs coated with ceramic or natural stone tiles. Its particular section and elegance, the availability in seven different finishes and special pieces such as internal and external corners, end caps and joints make PROJOLLY a much sought-after and elegant profile that allows a workmanlike application.
PJQTAC/S 045PJQTACML 045
EXTERNALCAPSULES
INTERNALCAPSULES
END CAP JOINT
EXAMPLES AND INSTRUCTIONS FOR LAYING METHODS
1. Choose “PROJOLLY QUART” according to the tile thickness and desired finish. 2.Cut “PROJOLLY QUART to the desired length and apply the adhesive on the supportwhere the profile will be laid. 3. Press the anchoring flange of “PROJOLLY QUART”into the adhesive. 4. Lay the tiles, aligning them with the profile leaving a 2 mm joint.Remove immediately all remains of adhesive from the surface of the profile. 5. Fill thejoints between the profile and the tiles with grout, in order to avoid water stagnation. Remove immediately all the remains of grout from the surface of the profile.
CAPSULES and END CAPS -POLISHED STAINLESS STEEL AISI 304/1.4301-V2A
JOINTS - PLASTIC
POLISHED STAINLESS STEEL AISI 304/1.4301-V2A with protective filmbar length 2,7 lm - pack. 30 Pcs - 10/10mm
Article H mm
CPJQTAC 045/... (external) 4,5IPJQTAC 045/... (internal) 4,5TPJQTAC 045/... (end cap) 4,5
Article H mm
GIJQT 045/... 4,5
CAPSULES and END CAPS - SATINED STAINLESS ST. AISI 304/1.4301-V2A
Article H mm
CPJQTACS 045/... (external) 4,5IPJQTACS 045/... (internal) 4,5TPJQTACS 045/... (end cap) 4,5
CAPSULES SUPER POLISHED STAINLESS STEEL AISI 304/1.4301-V2A
Article H mm
CPJQTACML 045/... (external) 4,5IPJQTACML 045/... (internal) 4,5
SUPER POLISHED STAINLESS STEEL AISI 304/1.4301-V2A thermo packedbar length 2,7 lm - pack. 30 Pcs81 lm - 10/10mm
SATINED STAINLESS STEEL AISI 304/1.4301-V2A with protective filmbar length 2,7 lm - pack. 30 Pcs - 81 lm - 10/10mm
Choose the desired packaging. E.g.: CPJQTAC .../10 (Pack. 10 Pcs) CPJQTAC .../2 (Pack. 2 Pcs)
Choose the desired packaging. E.g.: CPJQTACML .../10 (Pack. 10 Pcs)CPJQTACML .../2 (Pack. 2 Pcs)
Choose the desired packaging. E.g.: CPJQTACS .../10 (Pack. 10 Pcs)CPJQTACS .../2 (Pack. 2 Pcs)
Choose the desired packaging. E.g.: GIJQT .../10 (Pack. 10 Pcs)GIJQT .../2 (Pack. 2 Pcs)
SUITABLE FOR USE IN CONTACT WITH FOODSTUFFS.
H 4,5 mm
pro
files for lo
w th
icknesses
PJ... 03
PJ... 045
EXAMPLES AND INSTRUCTIONS FOR LAYING METHODS
1. Choose “PROJOLLY” according to the tile thickness and desired finish. 2. Cut “PROJOLLY” to the desired length and apply theadhesive on the support where the profile will be laid. 3. Pressthe anchoring flange of “PROJOLLY” into the adhesive. 4. Lay thetiles, aligning them with the profile leaving a 2 mm joint. Remove immediately all remains of adhesive from the surface of the profile. 5. Fill the joints between the profile and the tiles with grout, in order to avoid water stagnation. Remove immediately all the remains of grout from the surface of the profile.
POLISHED ALUMINIUM (chrome- gold) thermo packed bar length 2,7 lm - pack. 40 Pcs - 108 lm
POLISHED BRUSHED ALUMINIUM (silver-copper-titanium) thermo packedbar length 2,7 lm - pack. 40 Pcs - 108 lm
Article H mmPJBC 03 (polished chrome) 3PJBO 03 (polished gold) 3PJBC 045 (polished chrome) 4,5PJBO 045 (polished gold) 4,5PJBC 06 (polished chrome) 6PJBO 06 (polished gold) 6
ANODISED ALUM. (silver-gold) thermo packed bar length 2,7 lm - pack. 40 Pcs - 108 lm
Article H mmPJAA 03 (anodised silver) 3PJAO 03 (anodised gold) 3PJAA 045 (anodised silver) 4,5PJAO 045 (anodised gold) 4,5PJAA 06 (anodised silver) 6PJAO 06 (anodised gold) 6
Article H mmPJBS 03 (brushed silver) 3PJRS 03 (brushed copper) 3PJTS 03 (brushed titanium) 3PJBS 045 (brushed silver) 4,5PJRS 045 (brushed copper) 4,5PJTS 045 (brushed titanium) 4,5
H 3 mm
H 4,5 mm
PJ... 06 H 6 mm
Article H mmPJQTAC 045 (81 LM) 4,5PJQTAC 06 (54 LM) 6
Article H mmPJQTACML 045 4,5PJQTACML 06 6
Article H mmPJQTACS 045 4,5PJQTACS 06 6
PJQTAC/S 06 H 6 mm
pro
files for lo
w th
icknesses
COLOURS
AC - Polished stainless st. AISI 304/1.4301-V2A
ACML - Super polished stainless st. AISI 304/1.4301-V2A
ACS - Satin finish stainless st. AISI 304/1.4301-V2A
POLISHED, SUPER POLISHED AND SATINED STAINLESS STEEL AISI 304/1.4301-V2A / PLASTICCAPSULES, END CAPS and THREE-WAYS JOINTS
COLOURS A N O D I Z E D P O L I S H E D B R U S H E D P O L I S H E D
AA - Anodised silver alum. AO - Anod. gold alum. BC - Polished chrome alum. BO - Polished gold alum. BS - Brushed polished silver aluminium RS - Brushed copper alu. TS - Brushed polished
titanium alum.
= On demand, price and delivery time to be agreed.
