Cable Management Solutions no bleed marks

Cable Management SolutionsCatalogue 2019

ELECTRICAL PRODUCTSA division of ACTOM (Pty) Ltd

1ELECTRICAL PRODUCTS | A division of ACTOM (Pty) Ltd

Horizontally mounted cable ladder side rail heightClass designation

Structural steel S355, hot dip galvanized Stainless steel 304 & stainless steel 316

50mm/49,4mm/49,4mm

375mm

3.0m

76mm “Z” profile

100, 150, 200, 300, 400, 500, 600, 800, 1000

Radius 450, 650 & 1000mm

200mm = 10.0kg. 800mm = 15.2kg

Material

Inside depth

Standard length

Rung spacing

Side rail

Available widths (mm)

Accessories min. bend

Weight (3.0m)

Supports 2.0m 260kg/m 3.0m = 125kg/mSafe working load (swl)

Thickness t=1.5mm

F76 cable ladder (horizontally mounted)

Safe working load

F76 Straight (3m)

F76 cable ladder is manufactured in structural steel S355, stainless steel 314 and 316. Designed and and tested for horizontally mounted application in mining, light industrialand commercial, such as shopping centres andoffice buildings.

The structural steel cable ladder is made with structural steel S355. The stainless steel cable ladder is made with stainless steel 304. and 316. They are all light weight and ideal for shopping centres and building applications where the cables need to be supported on a horizontally mounted cable ladder and the supports are at 1.5, 2.0 or 3.0m. The ladder is designed and tested for horizontally mounted applications according to NEMA. The working load capacity for 1.5, 2.0 or 3.0m is shown in the safe working load diagram. The safety factor is 1.5. NEMA test load deflection is 20mm for 112kg/m safe working load. For the site installation the span will be continuous and the deflection is 10mm (end span 15mm). The F76 cable ladder meets the requirements of NEMA VE01 Class 10 B (112kg/m)(75lb/ft), support at 3.0m. (table 2 NEMA VE1-2009). All accessories require support near each end and at the centre. It is recommended that the F76 be installed in accordance with NEMA VE2- available from www.nema.org. The ladder is tested and certified according to the NEMA standard, by an independent PR engineer.

F76 horizontal bend F76 internal bend F76 external bend F76 tee F76 4-way

width

76

17

49.4

Supported span (m)1.50

100

200

300

400

500

2 2.5 3

125168

262

465

Safe

wor

king

load

(kg/

m)

2 ELECTRICAL PRODUCTS | A division of ACTOM (Pty) Ltd

Edge mounted cable ladderClass designation

Structural steel S355, hot dip galvanized stainless steel 304 & stainless steel 316

48.5mm

300mm

3.0m


100, 150, 200, 300, 400, 500, 600, 800, 1000

Radius 450, 650 & 1000mm

150mm = 11.7kg. 800mm = 18.2kg

Material

Inside depth

Standard length

Rung spacing

Side rail



Weight (3.0m)

See tableSafe working load (swl)

Thickness t=1.5mm

SB75 cable ladder (horizontally mounted)

Safe working load

SB75 straight (3m)

SB75 cable ladder is manufactured in structural steel S355, stainless steel 314 and316. Designed and and tested for horizontally mounted application in mining, light industrial and commercial, such as shopping centres andoffice buildings.

The structural steel cable ladder is made with structural steel S355. The stainless steel cable ladder is made with stainless steel 304. and 316. They are all light weight and ideal for shopping centres and building applications where the cables need to be supported on a horizontally mounted cable ladder and the supports are at at 1.5, 2.0 or 3.0m. The ladder is designed and tested for horizontally mounted applications according to NEMA. The working load capacityfor 1.5, 2.0 or 3.0m is shown in the safe working load diagram. The safety factor is 1.5. NEMA test load deflection is10mm for the safe working load. For the site installation the span will be continuous and the deflection is 5mm (end span 8mm). The SB75 cable ladder 800 and 1000mm wide meets the requirements of NEMA VE01 Class 10 B (112kg/m)(75 lb/ft), support at 3.0 m. (table 2 NEMA VE1-2009). All accessories require support near each end and at the centre. It is recommended that the SB75 be installed in accordance with NEMA VE2- available from www.nema.org. The ladder is tested and certified according to the NEMA standard, by an independent PR engineer.

SB75 horizontal bend SB75 internal bend

F76 equal reducer F76 right hand reducer F76 left hand reducer

SB75 external bend SB75 tee SB75 4-way

Supported span (m)

1.5

1000800400150

0

100

200

300

400

500

2 2.5 3

Safe

wor

king

load

(kg/

m)

60 5075

100 105150

125157

209

300

225180

width

75

20

48.5


Edge mounted cable ladderClass designation

Structural Steel S 355, hot dip galvanized Stainless Steel 304 and Stainless Steel 316

73.5mm

300mm

3.0m


100, 150, 200, 300, 400, 500, 600, 800, 1000

Radius 450, 650 & 1000mm

200mm = 15.0kg. 800mm = 20.8kg

Material

Inside depth

Standard length

Rung spacing

Side rail



Weight (3.0m)

Supports 2.0m 430kg/m 3.0m = 205kg/mSafe working load (swl)

Thickness t=1.5mm

SB100/SB150 cable ladder (horizontally mounted)

Safe working load

SB100/SB150 (3m)

SB100 cable ladder is manufactured in structural steel S355, stainless steel 314 and 316. Designed and and tested for horizontally mounted application in mining, light industrial and commercial, such as shopping centres and office buildings.

The structural steel cable ladder is made with structural steel S355. The stainless steel cable ladder is made withstainless steel 304. and 316. They are all light weight and ideal for shopping centres and building applications wherethe cables need to be supported on a horizontally mounted cable ladder and the supports are at at 1.5, 2.0 or 3.0m. The ladder is designed and tested for horizontally mounted applications according to NEMA. The working load capacityfor 1.5, 2.0 or 3.0m is shown in the safe working load diagram. The safety factor is 1.5. Nema test load deflection is10mm for 149kg/m safe working load. For the site installation the span will be continuous and the deflection is 5mm (end span 8mm). The SB100 cable ladder 800 and 1000mm wide meets the requirements of NEMA VE01 Class 10 B(112kg/m)(75 lb/ft), support at 3.0m. (table 2 NEMA VE1-2009). All accessories require support near each end and at the centre. It is recommended that the SB75 be installed in accordance with NEMA VE2- available from www.nema.org. The ladder is tested and certified according to the NEMA standard, by an independent PR engineer.

SB100 horizontal bend SB100 internal bend

SB100 equal reducer SB100 right hand reducer SB100 left hand reducer

SB100 external bend SB100 tee SB100 4-way

Supported span (m)1.50

200

400

600

800

1000

2 2.5 3

205

276

431

766

Safe

wor

king

load

(kg/

m)

width

100

20

73.5


Splice plates, covers & clamps

Splice plates

Covers

F76 straight flatcover

F76 horizontal flatcover

F76 internal flatcover

F76 external flatcover

F76 tee flatcover

F76 4-way flatcover

SB straight flatcover

SB horizontal flatcover

SB internalflat cover

SB external flatcover

SB tee flat cover

SB 4-way flatcover

LB straight flatcover

LB horizontal flatcover

LB internal flatcover

LB external flatcover

LB tee flat cover

LB 4-way flatcover

LB straight peaked cover

LB horizontalpeaked cover

LB internalpeaked cover

LB externalpeaked cover

LB tee peakedcover

LB 4-way peakedcover

F76 SPLICE PLATE SB75 SPLICE PLATE LB20 SPLICE PLATE


Horizontally & vertically mounted cable traysClass designation

Pre-galvanized steel Z275

12 & 19 mm “U” profile

50, 76, 101, 152, 203, 228 & 308

3.0m

Material

Dim. “H” may vary

Standard length


Thickness t=1.2mm

LT12 & LT19 cable trays

LT12 & LT19 cable tray (3m)

LT12 & LT19 cable trays is manufactured in pre-galvanized steel Z275. Designed for horizontal and vertical application.

OverviewThis cable tray range is a cable support system that is easily assembled on site. The LT12 & LT19 tray system is designed to carry electrical/data/voice cables in a horizontal and vertical application, up to a maximum width off 304mm. LT12 & LT19system is recommended in a light to medium-duty commercial application. With a full range ofaccessories this product provides an economical & flexible user-friendly solution that will satisfy the installing contractor’s as well as the end user’s electrical cable managing needs. Technical criteria The LT12 & LT19 straight comprises, a flat sheet 3,0min. length, bent up on both sides- 12mm high (up to 76mm wide)& this product provides an economical & flexible user-friendly solution that will satisfy the installing contractor’s as well as tray, to form a rigid channel like support. This tray system is manufactured as a standard, in pre-galvanized steel according to SABS ISO 3575:1996.

Loading criteria LT12 & LT19 cable tray is designed to carry a static electrical cable load not exceeding 140kg/m. The LT12 & LT19 straight must be supported every 1.0m maximum distance, where as the accessories require support near each end and at the centre.

LT12/19 horizontal bend LT12/19 internal bend LT12/19 external bend LT12/19 tee LT12/19 4-way

width

H



Commercial quality mild steel

38mm “U” profile

76, 114, 152, 228, 304, 457 & 609

3.0m

Material


Standard length


Thickness t=1.6mm

MT38 cable tray

MT38 cable tray (3m)

MT38 cable tray is manufactured in commercial quality mild steel. Designed for horizontal and vertical application.

OverviewThis cable tray range is a complete cable support system that is easily assembled on site. The MT38 tray system is designed to carry electrical cables in a horizontal and vertical application, up to a maximum width off 609mm. MT38 system is recommended in a medium to heavy-duty commercial application. With a full range of accessories this product provides an economical and flexible user-friendly solution that will satisfy the installing contractor’s as well asthe end user’s electrical cable managing needs.

Technical criteria The MT38 straight comprises, a flat sheet 3.0m in length, bent up on both sides (38mm high formed to a “u” profile) with Ø 11 x 25mm slotted perforations on the bottom of the tray, to form a rigid channel like support. This tray systemis manufactured as a standard, in commercial grade mild steel, hot dip galvanized to ISO 1461:1999. Straight lengthsand accessories are available in widths of 76, 114, 152, 228, 304, 457 and 609mm as a standard. All accessories cater for a minimum cable-bending radius of 450mm.

Loading criteria MT38 cable tray is designed to carry a static electrical cable load not exceeding 140kg/m. The MT38 straight must besupported every 1.8m (MT38) maximum distance, where as the accessories require support near each end and at thecentre.

MT38 horizontal bend MT38 internal bend MT38 external bend MT38 tee MT38 4-way

width

H



Z275 pre-galvanized mild steel


75, 100, 150, 225, 300, 450, 600, 750 & 900

3.0m

Material


Standard length


Thickness t=1.2mm

RM30/RME30 cable trays

Internal flange RM30 External flange RME30

cable tray

The return flange cable trays is manufacturedin Z275 pre-galvanized mild steel. Designed forhorizontal and vertical application.

Internal return flange

External return flange

OverviewThis cable tray range is a complete cable support system that is easily assembled on site. The MT38 tray system is designed to carry electrical cables in a horizontal and vertical application, up to a maximum width off 609mm. MT38 system is recommended in a medium to heavy-duty commercial application. With a full range of accessories this product provides an economical & flexible user-friendly solution that will satisfy the installing contractor’s as well as theend user’s electrical cable managing needs.

Technical criteria The MT38 straight comprises, a flat sheet 3.0m in length, bent up on both sides (38mm high formed to a “u” profile) with Ø 11 x 25mm slotted perforations on the bottom of the tray, to form a rigid channel like support. This tray systemis manufactured as a standard, in commercial grade mild steel, hot dip galvanized to ISO 1461:1999. Straight lengths and accessories are available in widths of 76, 114, 152, 228, 304, 457 and 609mm as a standard. All accessories caterfor a minimum cable-bending radius of 450mm.

Loading criteria MT38 cable tray is designed to carry a static electrical cable load not exceeding 140kg/m. The MT38 straight must besupported every 1.8m (MT38) maximum distance, where as the accessories require support near each end and at thecentre.

RM30/RME30 horizontal bend

RM30/RME30 tee RM30/RME30 4-way

width

width

HH



Z275 pre-galvanized mild steel


75, 100, 150, 225, 300, 450, 600, 750 & 900

3.0m

Material


Standard length


Thickness t=1.2mm

RH50/RME50 cable trays

Internal flange RM50External flange RME50

cable tray

The return flange cable trays is manufactured in Z275 pre-galvanized mild steel. Designed for horizontal and vertical application.

OverviewThis cable tray range is a complete cable support system that is easily assembled on site. The return flange cable tray system is designed to carry electrical cables in a horizontal and vertical application, up to a maximum width of 900mm. This system is recommended in a commercial environment. With a full range of accessories, this product provides an economical & flexible user-friendly solution that will satisfy the installing contractor’s as well as the end user’s electrical cable managing needs.

Technical criteria The return flange cable tray straight comprises, a flat sheet 3.0m in length, bent up on both sides with returned flanges (50mm high formed to a lipped “C” profile). Punched slots - Ø7.5 x 25mm longitudinal and Ø11 x 20mm lateral - on the bottom of the tray, allows continuous airflow throughout the entire installation. This tray system is manufactured as a standard, in commercial grade Z275 pre-galvanized mild steel. Hot dip galvanized to ISO 1461:1999 is manufactured to order. Straight lengths and accessories are available in widths of 75, 100, 150, 225,300, 450, 600, 750 and 900mm as a standard. All standard accessories have splices built-in and cater for a minimum cable-bending radius of: 50 - 225mm wide = 125mm, 300 - 450mm wide = 150mm, 600 - 900mm wide = 200mm andvariable risers all widths = 240mm.

Loading criteriaReturn flange cable tray is designed to carry a static electrical cable load not exceeding 140kg/m. The returnflange cable tray straight must be supported every 1.8m (RH50/ RHE50), maximum distance, where as the accessories require support near each end and at the centre. The return flange cable tray must not be used as a walkway.

RM50/RME50 horizontal bend

RM50/RME50 tee RM50/RME50 4-way

Internal return flange

External return flangewidth

width

HH



Commercial grade mild steel


50, 100, 150, 200, 300, 400, 500 & 600

3.0m

Material


Standard length


Thickness Ø=4 mm & 5 mm

WM50 cable tray

WM wire mesh50cable tray (3m)

WM50 cable tray is manufactured in commercialgrade mild steel wire. Designed for horizontaland vertical application.

OverviewThis wire mesh cable tray range is a complete cable support system that is easily assembled on site. It is a light to medium duty support system. The WM50 tray system is designed to carry electrical cables in a horizontal and vertical application. Technical criteriaWM50 system is recommended in a medium to heavy-duty commercial application. With its full range of accessories this product provides an extremely flexible and a user-friendly solution that will satisfy the installing 100 x 25mm apertures on both sides. This tray system is manufactured as a standard, in commercial grade mild steel wire, Zinc plated to Fe/Zn25A/T2 service condition 3, to ISO 2081:2008(E). WM50 straight and accessories is available in widthsof 50, 100, 150, 200, 300, 400, 500 and 600mm as a standard. All accessories cater for a minimum cable-bending radius of 450mm.

Loading criteriaWire mesh cable tray is designed to carry a static electrical cable load not exceeding 140kg/m. The WM50 straight must be supported every 1.0m maximum distance, where as the accessories require support near each end and at thecentre.

WM50 horizontalbend

WM50 internal bend WM50 external bend WM50 tee WM50 4-way

width

H


Unhardened Spring Nut and Grade 4.8 Hex Set ScrewM12 Spring Nut

Pull out Strength Resistance to Slip Maximum Tightening Torque

250

350

Use in F3300

Use in F1000

Size kg

180

180

kg

50

50

kg

Channels and spring nuts

Channel and combinationsChannels and combinations are cold formed to size from low carbon strip steel (minimum yield strength of 250 Mpa) on a rolling mill. The channel is manufactured with a continuous opening with the two edges turned inwards. Rigid mechanical fixing may be achieved by engaging the in turned edges of the channel with the serrated grooves in the spring nuts.

Spring nutsSpring nuts are produced from steel bar and, after manufacture, zinc plated nuts can be case hardened to order. Hardened spring nuts should be used with grade 8.8 zinc plated hex set screw. Generally, the South African market uses only unhardened spring nuts together with grade 4.8 zinc plated hex set screw. Spring nuts are rectangular in shape with the ends shaped as to allow a quarter turn clockwise and to prevent further turning in the channel. Twotoothed grooves in the top of the nut engage the return lips of the channel, in a vice-grip like manner. Allowable pull out strength and resistance to slip loads for torques shown.

Safety factor of 2

Channel and spring nut installation

1 2 3

4 5


AXIS X-X AXIS Y-Y

Metal Framing Channel

Description

Thickness(mm)

Area ofSection(mm²)

Weight ofProduct

g/m

110³

mm⁴

Z10³

mm³

R

mm⁴

110³

mm⁴

Z10³

mm³

R

mm

F100 2.50

673.49

2644

5287

72.367

370.48

3.147

8.97 23.454

14.66

183.81

91.904

8.901

4.45

16.52

16.25336.75

2.50F1001

Channels

F1000 channel(41.3 x 41.3 x 2.5)

F1001 channel(41.3 x 82.6 x 2.5)

F1001A F1001B F1001C F1001-C4 F1001D

Design fundamentals - column end conditionsK = the effective length factor, which mathematically describes the

column end conditions.

F3301


Length FixingHoles

Unit Mass

kg

TotalULGkg

150 1

347

272

473

1

1

0.60

0.80

1.00

200

250

1921 1.20350

1502 1.60450

1242 1.80550

1022 2.00650

LengthUnit

Masskg

TotalULGkg

150 0.91

1.10

1.30

473

347

272

200

250

1.50 192350

1.70 150450

2.00 124550

2.20 102650

LengthLong

LengthShort

Unit Mass

kg

TotalULGkg

650 250

208

180

288

300

350

3.00

3.60

4.40

850

1050

LengthUnit

Masskg

TotalULGkg

650 4.20

5.20

6.40

288

208

280

850

1050

LengthUnit

Masskg

TotalULGkg

150 0.88

1.02

1.16

473

347

272

200

250

1.43 192350

1.70 150450

1.97 124550

2.24 102650

Cantilever brackets

Single cantilever bracket

F233, F254, F254S, F254D & F251 Cantilever bracketsThe cantilever bracket system is manufactured from mild steel and utilises F1000 channels welded to a back plate. All cantilever support arms for cable ladders and trays should be 50mm longer than the width of the cable ladder ortray used. The safe working load for cantilever arms is uniformly distributed over the length of the cantilever support arm. Standard finish on cantilever brackets is hot dip galvanised.

F223-90 cantileverbracket

F223-135 cantileverbracket

Staggered cantileverbracket

F254D cantileverbracket 1A

F223-135T cantileverbracket 1B

F223-135T cantileverbracket


Angular fittings

Flat fittings

General fittings

F1026 F1033 F1035 F1068F1034

F1074 F1130/31 F1325 F1359F1186/45

F1546/45 F1713 F1749 F2484F1747

F1036

F1062/3/4

F1028 F1031 F1065F1066


‘K/U’ CableClamp

Cable orPipe

dia. (mm)

K/U2026

K/U2027

K/U2028

K/U2030

K/U2032

K/U2034

K/U2036

K/U2038

K/U2040

K/U2042

K/U2043

K/U2044

14

16

20

26

32

40

46

52

58

66

70

78

ProductRange

Cable orPipe

dia. (mm)

F2025F1108F2026

F1108AF2027F1109F2028F1111F2023F1113F2023F1113F2034F1114F1115F2038F2039F1117

F2043

F1118F1119

F1120F1121F1122F1123F1124F1125

F1126F1127F1129

7.5-147.13

11.5-13.510.5-1513-1715-18

16.5-19.519-2321-3024-2927-3532-3632-3938-4443-5747-5747-6154-70

62-75

71-8587-95

99-110110-122116-140135-145155-180175-206

188-22235-270260-285

M6 x 20mmM6 x 20mmM6 x 20mmM6 x 20mmM6 x 20mmM6 x 20mmM6 x 20mmM6 x 20mmM6 x 20mmM6 x 25mmM6 x 25mmM6 x 25mmM6 x 25mmM6 x 25mmM8 x 35mmM8 x 35mmM8 x 35mmM8 x 35mm

M8 x 35mm

M8 x 35mmM8 x 35mm

M10 x 50mmM10 x 50mmM10 x 50mmM10 x 50mmM10 x 60mmM10 x 60mm

M10 x 60mmM10 x 60mmM10 x 60mm

Hex SetScrew

Size (& Nut)

ProductRange

Pipedia. (mm)

F2239/20F2239/25F2239/30F2239/40F2239/60F2239/80F2239/100F2239/120

607689114166219273324

M12 x 45mmM12 x 45mmM12 x 45mmM12 x 60mmM12 x 60mmM12 x 70mmM12 x 70mmM12 x 70mm

Bolt & NutSet Size

Pipe clamps

Two piece pipe/ cable clamps

F2239 Series pipe clamps

Clamps

Finish: hot dip galvanised Fasteners: yellow passivated

Finish: pre-galvanised Fasteners: electro-galvanised

Finish: hot dip galvanised

‘K/U’ clamp ‘K/U’ clamp

Two piece pipe/cable clamp

F2239 pipe clamp

Hanger

‘K/U’ clamp


PartNo.

ER19-23ER23-28ER27-32ER30-35ER33-38ER36-42ER40-46ER44-50ER48-55ER51-58ER55-62ER59-66ER63-70ER67-74ER71-78ER74-82ER77-85ER82-88ER88-96ER96-103ER103-111ER111-119ER119-128

1923273033364044485155596367717477828896103111119

23283235384246505558626670747882858896

103 2111119128

96969799103124125130132136160163166169172177183191

207 221237253

265 2

8383889195

10010611712112813514315115816517117718703

21823525075

5454545454545454545454545454545454545454545454

2525252525505050505075757575757575757575757575

2 x M10 + 1 x M122 x M10 + 1 x M122 x M10 + 1 x M122 x M10 + 1 x M122 x M10 + 1 x M122 x M10 + 1 x M122 x M10 + 1 x M122 x M10 + 1 x M122 x M10 + 1 x M122 x M10 + 1 x M122 x M10 + 1 x M122 x M10 + 1 x M122 x M10 + 1 x M122 x M10 + 1 x M122 x M10 + 1 x M122 x M10 + 1 x M122 x M10 + 1 x M122 x M10 + 1 x M122 x M10 + 1 x M122 x M10 + 1 x M122 x M10 + 1 x M122 x M10 + 1 x M12

2 x M10 + 1 x M12 1

4254254404454606006056306406508108258508508908909058208909409501010220

Cable Range

Min. Dia.(mm)

Max. Dia.(mm) W H D P Fixing Holes

Dimensions (mm) Weight(g)

Ellis cable cleats

Holding powerWith 50 years of innovation and testing behind us, we are recognised as the world’s leading supplier of safety critical electrical cable cleats. Every day, vital operations and services such as the channel tunnel rail link, nuclearpower plants and oil rigs rely on our products to keep them running safely. Holding power is our guarantee that Ellis cable cleats will contain short-circuitforces - protecting your people, power and plant, without fail.

Tested to perfectionSince the birth of the business, we’ve been working with independent test houses to raise safety standards within the industry. We understand the science behind the appropriate standards, but we know that results from short-circuit testing are what really counts. Testing is the only way to prove that a cleat will do its job. We undertake regular testing in accordance withthe international standard IEC61914, and the results show that our productsexceed industry requirements. This uncompromising quality and our ‘safety first’culture, guarantee your protection. We’re more than happy to make available reports and video footage from our tests.

Section table for Trefiol cable application


Lindapter

BackgroundFor more than 75 years, Lindapter has earned a respected reputation as the inventor and pioneer of steelwork clamping systems, providing an independently approved and exclusive product range of steelwork, cavity, decking, support and steel floor fixings.

Lindapter’s unique connections create significant advantages in comparison to traditional methods such as welding or drilling, including the reduction of installation time and labour costs, on-site adjustability and no damage to steel sections or protective coatings.

The company’s proud heritage began in 1934 when engineer Henry Lindsay invented an entirely new concept of connecting steelwork with the Lindsay Bolt Adapter, allowing simple, fast clamping, instead of often difficult and time consuming drilling or weldings. The idea was to revolutionise millions of future connections on countless projects worldwide and the combination of the two words ‘Lindsay’ and ‘Adapter’ explains the formation of the now famous brand names.

Today, Engineers across the world choose Lindapter for projects as varied as Rome Train Station, Gatwick Airport, Alexander Hamilton Bridge, Dubai Shopping Mall and Gautrain Rapid Rail Link. Whether joining primary structural sections, securing secondary beams or suspending building services, Lindapter has a proven and trusted solution.

Lindapter has passionately grown over 75 years from a modest family business, into a reputable global brand and strives to continue its proud heritage inventing ‘technical innovation in steelwork connections’.

17ELECTRICAL PRODUCTS | A division of ACTOM (Pty) Ltd 17ELECTRICAL PRODUCTS | A division of ACTOM (Pty) Ltd

Projects

Steelwork fixings

Project: St Pancras Station, London Country: UKProduct: Type AFApplication: The connection of a new roof to the existing structure.

Cavity fixings

Project: HafenCity, Hamburg Country: GermanyProduct: Type HBFF - Hollo-Bolt Flush FitApplication: Connecting the hollow section glazing support frame.

Decking fixings

Project: Canary Wharf, London Country: UKProduct: Type AW - AlphawedgeApplication: The suspension of building services from composite decking.

Support fixings

Project: Manhattan Bridge, New York CityCountry: USAProduct: Type F3Application: Pipe support.

Floor fixings

Project: Docklands Light Railway, LondonCountry: UKProduct: Type FF - FloorfastApplication: Securing a maintenance walkway.

®

®


Framo: modular steelwork solutions

We understand the problems you face. Budgetsare exceeded, schedules often over run and wehave identified the challenges facing secondary steel solutions.

- Excessive waste by modification.- Weight is high, performance is poor.- Logistics are outdated and inefficient.- A hot works facility is required.

With the experience of over 40 years in developinginnovative products for above-ground industrial pipe work installation, we believe it is possible towork in a way that is more efficient and more productive for everyone involved.

With Strutfast you can plan smarter through provendesign and innovation, here is how:

Framo A versatile, multifunctional support system that offers maximum flexibility using a compact range of off-the-shelf components used in partnership with our SIMOTEC modular pipe supports. All of our systems can be fully implemented in to the CAD process at planningstage.

Key benefits- All parts are reusable without wastage.- Strong but lightweight, cutting down the total tonnage of steel required for the project.- Our products are readily available from stock with a distribution network that offers quick lead times.- There is no need for hot works!

These benefits form the foundation of Framo:Lightweight from only 4.3kg per m, offering easily adjustableconnections secured with minimal assembly using a threadforming, shake proof fastening.

All Framo 80 and 100 products are fully compatible with all other SIKLA system parts including our SIMOTEC pipe support range. High load bearing and height adjustable as standard with approximately 50mm of adjustability per pipeshoe.

Why use us?We can support you at every stage of the project and all of our products benefit from optimal design, performance andquality. Guaranteed to save you time and reduce costs.

ELECTRICAL PRODUCTS | A division of ACTOM (Pty) Ltd

CONTACT US

JOHANNESBURG4 Branch Road, Driehoek, Germiston, 1401

Tel +27 (0) 11 878 3000E-mail: [email protected]

WELKOM29, 10th Street, Voorspoed, 9459


449 Skilder Street, Silvertondale, 0184Tel +27 (0) 12 804 0551

E-mail: [email protected]

PRETORIA

SOUTH AFRICA

CAPE TOWN12 Hawkins Avenue, Epping Industria No 1, 7460


Cnr Kragborn and Bester Street, 1201 Tel +27 (0) 13 753 2121


NELSPRUIT PORT ELIZABETH200 Kempston Road, Sidwell, 6001


20 Lombard Street, Hilton, 9301Tel +27 (0) 51 448 1417


BLOEMFONTEIN DURBAN70 Soloman Mahlangu Drive, Rossburgh, 4094


ELECTRICAL PRODUCTS | A division of ACTOM (Pty) Ltd

SOUTH AFRICA AFRICA

Updated: 07/19e.&o.e

POLOKWANE115 Blaauwberg Street, Ladine, 0699


NAMIBIAUnit 5, No 13 Gold Street, Prosperita

Tel +264 6142 3150E-mail: [email protected]

STEELPOORTStand No 1194/1, Tweefontein farm, Ext 10


ZIMBABWE (GEC- HARARE)9 Cam Road, Graniteside

Tel +263 4 770 760E-mail: [email protected]

ZIMBABWE (GEC- BULAWAYO)4 Cardiff Street, Bulawayo

Tel +263 9 664 01E-mail: [email protected]

RUSTENBURGUnit 7, 13 Tigerfish Street, Waterval, 0299

Tel +27 (0) 14 596 9912/3/4E-mail: [email protected]

EAST LONDONUnit 1, 32 Dyer Street, Arcadia, 5200

Tel +27 (0) 43 731-1996E-mail: [email protected]

www.actom.co.za

NOTE:

Cable Management Solutions no bleed marks

Documents

Transcript of Cable Management Solutions no bleed marks