Cable Entry via Metric Knockouts - Hi-Tech Controls · Cable Entry via Metric Knockouts • Plenty...

~ HI·TECH ~ CONTROLS, INC.

DK Cable Junction Boxes with Terminals in Plug-in Technology

Cable Entry via Metric Knockouts

• Plenty of space for 1he W:ring: Wiring fadlities both below the DIN rails and between the tetminals.

. ~·

• Stainless steel cover sc.rews with quick fastering metric thread. Reducing cover fixing time.

• Different conductor types - rigid (r) and flexible (f) without treatmem o' conductors - can be cornected in one terminaL

• Labelling system for circuit description • Label template on 1he Internet at

www.hensel-aectric.de- in ihe 'DCJNnloads' area.

Ca ll for a Quote! (800) 677·8942 I (303) 680·5159

www.hitechcontrols.com

• Conductors can be directly connected and disconnected with installed terminal.

• Burning behaviour: Glow wire test accorc!Sng to IEC 00 B95-2-1 1 : 750 oc. flame-retardant, self-extinguishing

19

tu Ul a u > c Ul


11.1 Ill a u > c w

DK Cable Junction Boxes with Terminals in Plug-in Technology

Cable Entry via Metric Knockouts

KC 9045 1.5-4 mm2, Cu 3-

• RXCONNECT• plug-in tenninal technology

20

• 5-pole per pole 4 x 1 x 1,5-4 ~ so!lf, terrnnal technology, see anne< DK Cable junction boxes

• induded cable enby: 4 ESM 25, seali-!g range 0 9-17 mm

• for normal environment and protected outdoor

rated nsularlon voltage current canyilg capacity

KC 9255 2.5-1 0 mm2 , Cu 3-

AC/DC690V 32 A

• RXCONNECT- plug-in tenninal technology • 5-pole per-pole4x 1 x 2.5-10 ~r/f • induded cable enby: 3 ESM 32,

sealilg range 0 9-23 mm • for normal environment and protected outdoor

rated ·nsulation voltage current canying capacity

KC 9355 2.5-16 mrn2 , Cu 3-

AC/DC690V 50 A

• RXCONNECT- plug-in tenninal technology • 5-pole perpole 4 x 1 x 2.5-16 ITlfTl2 r/f • induded cable enby: 3 ESM 40,

seamg range 0 17-30 rrm • for normal environment and protected outdoor

rated insulation voltage current canying capacity

AC/DC690V 76A

Ca ll for a Quote! (800) 677·8942 I (303) 680·5159


IP ~~ l 55 ~~ Ps

1 65

1P !I IP PS ......---- ..----. ~ j 55 1 65

.........-- 10) RAL 6 .. 6 (7005 toL

l-t:!!i-f l·lo--1

IO[]

......----. - f& r RAL 8 w.a 8 poos u ]

t3 f5 ... i6

t3]

o m


DK Cable Junction Boxes Cable Entry via Metric Knockouts

• Variable terminal mounting positions (5 oositions) and new terminal technology

r ... ,. .. .. '

• lnduded accessories as fisted: grommets ESM = IP 55

t .... r··~ J

. ~·

• Stainless steel <XNer screws with qtJick fastening metric thread. Reducing cover fiU,g time.

14/2

• L.abelling system for circuit description • Label template on the Internet at

IIVINW.hensel-electric.de- in !he 'Dovmloads' area.

Ca ll for a Quote! (800) 677·8942 I (303) 680·5159


• Hensel cable jtJnction b(]l(es can in general also be used in jX)or en~~ironmental concitions by using IP 65 cable gtands AJ<MI ASM.

• Buming behaviour: GICMI wire test according to IEC 60 695-2-11:750 °C / 9€0 OC, flame-retardant, self-extinguishing

21

ill VI (L u > c \II


Col Ill a u > c w


D 9025 1.5-2.5 mm2 , Cu 3.-

• with terminals • 5-pole per pole 6 x 1.5 mm2 sol, 4 x 2.5 rnrn2 sol, 3 x 4 mm2 sol • induded cable entry: 4 ESM 20,

seal61g range 06-13 mm • for normal environment and protected outdoor

rated 1nsulation voltage tightening torque for terminal

D 9 125 1.5-2.5 mm2 , Cu 3.-

• with terminals

AC/DC690V 1!2Nm

• 5-pole per pole 6 x 1.5 mm2 sol, 4 x 2.5 rnrn2 sol, 3 x 4 mm~ sol • induded cable enby: 4 ESM 20,

sealing range 0 6-13 mm • with external fixing • for normal environment and protected outdoor

rated "nsulation voltage tightening torque for terminal

D 9045 1.5-4 mm2 , Cu 3-

• with terminals

AC/DC690V 1,2 Nm


1P ; ,...;- r PS { 55 [ 65

,.,.,.--- 3 RAL 3Wd3

l7035 L; i l

IP ~~~ [ 55

1-BB---i j.:.:.-1

!nO]

IP RAL --F ...---I 65 PS f7035

• 5-pole per pole 6 x 1.5 mm2 sol, 4 x 2_5 ITli1'J2 sol, 3 x 4 mm2 sol, 2 x 6 rnrn2 sol

22

• inducted cable entry: 4 ESM 25, sealing range 0 9-17 mm

• ;or norrnal environment and protected outdoor

rated"nsulationvoltage tightening torque for terminal

K 9065 2.5-6 mm2, Cu 3-

• with terminals

AC/DC690V 1!2Nm

• 5-pole per pole 4 x 2,5 mm2 sol, 4 x 4 mm2 sol, 3 x 6 mrn2 sol, 2x 10 mm2sol

• induded cable enby: 3 ESM 32, seal"I'lg range 0 9-23 mm


rated nsulation voltage tightening torque for terminal

~

AC/DC690V 1,5Nm

Ca ll for a Quote! (800) 677·8942 I (303) 680·5159

IP PS RAL 6 Wd 6 r--F ...--- -~

1 65 f7ros toJ

J-139-f 1--70-1

IDOJ



K9105 4-10 mm2 , Cu 3-

• with terminals • 5-pole per pole 6 x 2.5 mm2 sol, 4 x 4 mm2 sol, 4 x 6 ~sol,

4x 10mm2so1,2x1S~s • induded cable enby: 3 ESM 32,

sealing range 0 9-23 mm • for normal environment and protected outdoor

rated ins1.11ation voltage current carrying capacity rightering torque for terminal

K9255 10-25 mm2, Cu 3-

• with terminals

ACIDC S90V 63A

2,0Nm

• 5-pole perpole6x 10 mm2 sol, 4 x 16mm2s, 4x 25 mm2s, 2x 35 mm2s

• induded cable entJy: 3 ESM 40, sealing range 0 17 -so mm

• Cor normal environment and protected outdoor

rated 'ns1.1lation voltage current carrying capacity tightaing torque for terminal

K9502 1Q-35 mm2 , Cu 3 -

• with terminals

ACIDC690V 102A

3,0Nm

• 5-pole per pole 4 x 10 mm2 sol, 4 x 16 mm2 s, 4x 25 rnrn2 s, 2x 35 mm2s

• induded cable entJy: 3 ESM 40, sealing range 0 17 -so mm


rated nsulation voltage current canying capacity tightering torque for terminal

K9355 16-35 mm2 , Cu 3-

• with terminals

ACIDCS90V 102A

3,0Nm

• 5-pole per pole 6 x 16 mm2 s, 4 x 25 rnrn2 s, 4 x 35 mm2 s, 2x 50 mm2s

• induded cable entJy: S ESM 40, sealing range 0 17 -so mm

• tor normal environment and protected outdoor

rated 'nsularion voltage current canying capacity tightening torque for terminal

ACIDC 690V 125A

12,0 Nrn

Ca ll for a Quote! (800) 677·8942 I (303) 680·5159


lP ;

( 55

IP ~ ! 55

lP ;

[ 55

IP ~~ ! 55

-,P- r PS [ 65

IP r PS [ 65

« RAL 6-6 17035 ..JiOL

l~lfl7~11-82--l

IDa

16 8-8

111

l-200----ll-se-1

fDOJ

IP r PS ! 65

RAL

[ 7035

·,.....:-;..--

. ....._.__

IP r PS [ 65 RAL 17035

23

w •n a

> c Ul

141 tn a u > c w


24


•

•

K 9504 16-50 mm2, Cu 3 -

• with terminals • 4-pole per polel6 X 16 mm2 S, 4 X 25 flll'n2 S, 4 X 35 mm!l S,

4x 50 mm2s • cable en1Jy via knockouts, order AKMf ASM sepatateJy (refer to

index cable enby systems) • for nom1al environment and protected outdoor

rated nsulation voltage current canying capacity tightening torque for terminal

K9505 16-50 mm2, Cu 3-

• with terminals

AC/DC690V i50A

12,0 Nrn

• 5-pole per pole 6 X 16 mm2 S, 4 X 25 rnrJ12 S, 4 X 35 mm!l S, 4x 50 mm2s

• cable enVies via knockouts order AKMIAKS separately (refer to index LES)


rated "nsulation voltage current canying capacity 1ightering torque for terminal

K 7055 16-50 mm2, Cu 3 -

• with terminals

AC/DC690V 150A

12,0Nm

• 5-pole per pole 6 x 16 mm2 s, 4 x 25 f"Tlrrl! s, 4 x 35 mm2 s, 4x 50 mm2s

• sealable • Order cable glands, flanges and other accessories separately as

required • for normal environment and protected outdoor

rated .nsulation voltage current canyTig capacity tightening torque for terminal

K7004 16-70 mm2, Cu 3 -

• with terminals • 4-pole per pole 4 x 16-70 mm2 s • sealable

AC/DC690V i50A

12,0Nm

• Order cable glands, flanges and other accessories separately as required

• for nom1al environment and protected outdoor

rated nsulation voltage current canying capacity tightening torque for terminal

AC/DC690V 216 A

10,0 Nm

Ca ll for a Quote ! (800) 677·8942 I (303) 680·5159


IP

l 65

r l

.,--RA.L

[7035

rf---"o------4 ~0 ;;;

11-------1 --

~300

~ .

--

--

- 20 -21 .... 21

20

,___ lTC

- 20

[PC RAL 21Wal 21

17032 20J

~HI-TECH ~ CONTROLS, INC.


K7005 16-70 mm2 , Cu 3-

• with terminals • S.pdeperpolel4x16-70mm2s • sealable • CXder cable glands, flanges and other accessories separately as

required • fcx normal environment and protected outdO()(

rated nsulation voltage current canyW1g ca,pacity tightering t~ tr terminal

K 1204 16-150 mm2 , Cu/AJu 3-

• with terminals

AC/DC690V 216A

10,0 1\m

• ~pole per pole 2 x 16-150 mm2, 4 x 16-70 mm2, conductors can be rnserted from the front nto the ~ lril. terrnnal technology, see anne< DK Cable junction boxes

• sealaole • CXder cable gtands, flanges and other accessories separately as

required • Reference to the preparation of atJrrir-.Jm conductors:

~ . Oean the bared conductcx end carefUiy by scrapng off the oxJde f;'m, ccx e<ample whh a knife (Please do not use rasps, emey paper or brushesO.

2. Immediately after removing the oxide film the conduct ex end is to rub in wth acid and alkali free fat for e<ample vaseline, and rnmediately to be comected n the terminal.

3. The prementioned processing steps are to be repeated, if the conductor was disconnected and connected again.

• 4. Due to the disposition to flawing of aluminum the termnals are to be re-tightened be'ore start-up and after the f1rst 200 operation hours.

• fcx normal environment and protected outdoor

rated · nsulation voltage currentcanyingcapadiy

tightenng torque fcx terminal

AC/DC690V 250A

20,0 1\m

Ca ll f or a Quot e! (800) 677·8942 I (303) 180·5159


IP

165

:i .. ..

PC

~

1~

E nYCASE"

20

RAt. 2 i - 2i 7032 20

~

~

~

IP PC RAL -F-1 65 7002

20J 2i ... 2t

20

25

(II ttl a u > c w


w Ill a v > c I;)

26


K 1205 16-150 mm2 , CufA ,Ju 3-

• with terminals • 5-pole per pc:Me 2 x 16-150 mrn2, 4 x 16-70 m,.,:Z,

conductors can be inserted rrom the front into the clamping unit. terminal technc:Mogy, see annex DK Cable junction boxes

• sealaole • C:Xder cable ~ds, ftanges and other accessories separately as

required • Reference to the preparation of .Wrrinrrn conductors:

1. Oean the bared conductor end carefulty by scraping off the oxide fJm, for example with a knife, {Please do not use rasps, emery paper or brushes!).

2. lmmediate.'y after removing the oxide film the conductor end is to rub in with add and all<ali free fat for exarrple va:se!ine, and immediately to be comected in 1tte terminal.


• 4. Due to lhe disposition to flowing of aluminum the termnals are to be re-tightened before start-up and after the first 200 operation hours.


rated·nsu~onvottage

current c:anying capacity tightenng torque for terminal

K2404 25-240 mm2 , Cu/Alu 3-

• with terminals

AC/DC 690V 250A

20,0Nm

• 4-pole perpc:Me2x 25-185/240 rnrr?, 4x25-120 mm2, conductors can be inserted from the front into the clamping unit. terminal technc:Mogy, see annex DK Cable junction boxes

• sealable • C:Xder cable glands, ftanges and other accessories separately as

required • Reference to 1tte preparation of aJurrinum conductors:

1. aean the bared conductor end carefulty by scraping off lhe oxide film, for example with a knife, {Please do not use rasps, emery paper or brushes!).

2. Immediately after removing the oxide film the conductor end is to rub in with add and alkali free fat for exarrpleva.seline, and immediately to be connected in 1tte terminal.

3. The prementioned processing steps are to be repeated, if the conductor was cfisconnected and connected again.

4. Due to the disposition to flowing of aluminLnJ the termnals are to be re-tightened before start-up and after the first 200 operation hours.

• for nOfTTlal environment and protected outdoor

rated nsulation voltage current carrying capacity tightering torque for terminal

AC/DC690V 400A

40,0Nm

Ca ll for a Quote ! (800) 677·8942 I (303) 680·5159


IP~ I 65 I .... RAL

[7032

IP RAL .---F r----. I 65 PC J7032

20 21-21 L 2DL

[,_.,_,>:!._,_,

g Iii I ... -



K2405 25-240 mm2, Cu/Aiu 3-

• with te~minals • 5-po!e perpole2x 25-185/240 ~. 4 x 25-120 mm2,

conductors can be inserted from 1he front i1to the clamping unit, term:nal technology, see anne< OK Cable junction boxes

• sealable • Order cable glands, flanges and other accessories separately as

required • ~terence to the preparation of aturrinum conductors:

1. O ean the bared conductor end carefully bj scraping off the oxide tim, for e<ample with a knife, (Please do not use rasps, emery paper or brushesO.

2. lmmediatety after removing the oxide film the conductor end is to rub in with acid and alkali free fat for ex~le vaseline, and immecfiately to be connected in the te~minal.


• 4. Due to ihe disposition to ilawing of aluminum the teminals are to be re-tightened before start-up and after the first 200 operation hours.


rated ·nsulation voltage current canying capacity tighten..ng torque for terminal

ACIDC690 V 400A

40,0Nrn

Ca ll for a Quote! (800) 677·8942 I (303) 680·5159


IP ..--- ~ I 65 PC

20 19 .... 19

..JiBL

27

w Ul a u > c w

w Ill a v > c w


28


D 9020

• without terminals • induded cable enby: 4 ESM 20,

seafing range 0 6-13 mm • for normal environment and protected outdoor

D 9120

• without terminals • with ext:emaJ fixing • induded cable enby: 4 ESM 20,

seali-lg range 0 6-13 mm • for normal environment and protected outdoor

D 9140


sealing range 0 6-13 mrn • for normal environment and protected outdoor

D 9040



K9060


seali-lg range 0 9-23 mm • for normal environment and protected outdoor

Ca ll for a Quote ! (800) 677·8942 I (303) 680·5159


IP ;

55 IP I PS j 65

3 3 .... 3

.. IJ> ; ' w- r;;- oo- 3'.:. 3

I 55 I 65 I r-. [7035 L f

IP I PS [ 65

1-Ba-ll..sli

l[][]

l--98--ll·!hol

IDOJ

.r-RAL [ 7035

..---------RAL

17035

10 6 ... 6

iO

l-139-ll-101

ID[]



K 9100

• without terminals • induded cable entry: 3 ESM 92,


K 9250

• without terminals • induded cable entry: 3 ESM 40,

sealing range 0 17-30 rrm • for normal environment and protected outdoor

K9350


sealing range 0 17-30 rrm • for normal environment and protected outdoor

K 9500

• without terminals • cable entry via knockouts, order AKMIASM separately (refer to

index cable entry systems) • for normal environment and protected outdoor

Ca ll for a Quote ! (800) 677·8942 I (303) 680·5159


...----.. IP 1!1 55 ~~ PS 165

RAL [7005

IDDJ

rorn --

--

29

u. VI a u > c \II


DK Cable Junction Boxes Box Walls without Knockouts

1&1 Ill CI u > c 11.1

-

Cable en!Jies can be drilled individually.

• Burning behaviour:

30

Glow wire test according to IEC 60 695-2-11: 750 oc. flame-retardant, self-e<tinguishing

• Labe!ling system for circuit description • Label template on the Internet at

www.hensel-electric.de- in the 'Downloads' area.

Ca ll for a Quote! (800) 677·8942 I (303) 680·5159


•

• • Stainless steel cOYer screws with quick

fastening metric thread. ~educing OCNec fixing time.



0 8020

• without terminals • box walls without knockouts • walJ surlace can be drilled indMdua!y for cable entry max. M 20 • for normal environment and protected outdoor

wall thickness of the bottom part 2,3mm

~

D 8120

• without terminals • with e<temal fixing • box walls without knockouts • wall surface can be drilled indMdua!y for cable entry max. M 20 • for normal environment and protected outdoor


0 8040

• without terminals • box walls without knockouts • wall surface can be drilled indMduaJy tor cable entry max. M 20 • for normal environment and protected outdoor


K8060

• without terminals • box walls without knockouts • walJ surface can be drilled indMdualy for cable entry max. M 32 • for normal environment and protected outdoor


K 8100

• without terminals • box walls without knockouts • wall surface can be drilled individualy for cable entry max. M 32 • for normal environment and protected outdoor

wall thickness of the bottom oart 2,8mm

Ca ll for a Quote! (800) 677·8942 I (303) 680·5159


~ lP

[ 65 PS -=-RAL

[7005

(--111-i 101

l[]{]

I1

P 65 F 'ff005

(--111-.j 101

i[]Ol

1P

~

...--RAL

[7005

1-167-J f-a2-l

ID[]

31

w Ul a u > c w

"" Ill a u > c 1:.1


32


K 8250

• withotJt taminals • box walls without knockouts • walJ surface can be drilled individualy for cable entry max. M 40 • for normal environment and protected outdoor

wall thicl<ness of the bottom part 3rrm

~

K8350

• withotJt terminals • box walls without knockouts • wall surface can be drilled incfrvidua)y for cable entry max. M 50 • for normal environment and protected outdoor

waiJ thld<ness of the bottom part 3rrm

K8500

• withotJt terminals • box walls without knockouts • wall surface can be drill.ed individu.aJy for cable entry max. M 50 • for normal environment and protected outdoor

wall thid<ness of the bottom part 3rrm

Ca ll for a Quote ! (800) 677·8942 I (303) 680·5159


.= -= IP I RAL I 65 PS 17005

ItoDJ ,p RAL ..---F .---

1 65 PS T7005

10 m IP RAL

[ 65 [7005

I f==?1o-----. I=:!~

""

l --



K 0100

• with transparent lid • lid fasteners for tool operation • box walls without knockouts • please order DIN rails or mounting plates additionally • for normal environment and protected outdoor

rated current wall thickness of the bottom part

K0200

• with transparent lid • lid fasteners for tool operation • box walls without knockouts

for electrical devices up to 63 A 3,5mm

• please order DIN rails or mounting plates aaditionally • for normal environment and protected outdoor


K0300


for electrical devices up to 63 A 3,5 mm

• please order DIN rails or mounting plates additionally • for normal environment and protected outdoor

rated curTent waiJ thickness of the bottom part

K0400



• please order DIN rails or mounting plates additiona ly • for normal environment and protected outdoor

rated curTent wall thickness of the bottom part


Ca ll for a Quote! (800) 677·8942 I (303) 680·5159


( 65 IPS ~035 1-~I--170-..J

IC JOJ

( ss I PS ~

D OJ IP r PS RAL 1 65 [7035

roa IP RAL ..----F.---I 65 PS [7035

33

w Ul a u > c Ul


w tn a u > c w

34


•

•

K 0101

• with opaque lid • lid fasteners for tool operation • box walls without knockouts • please order DIN rails or mounting plates additionally • for normal environment and protected outdoor


K 0201

• with opaque lid • lid fasteners for tool operation • box walls without knockouts



rateo current wall !hickness of the bottom part

K 0301

• with opaque lid • lid fasteners for tool operation • box walls without knockouts



rated current for electrical devices up to 63 A wall thickness of the bottom part 3,5 mm

K 0401

• with opaque lid • lid fasteners for tool operation • box walls without knockouts • please order DIN rails or mounting plates additionally • for normal environment and protected outdoor


for electrical devices up to 63 A

3,5mm

Ca ll for a Quote! (800) 677·8942 I (303) 680·5159


~~ roos l-300=-l H ro-t

I( J[]

tP RAL ..-F..-I 65 PS [7035

IP6S [ PS RAL l7005

Oil .---RAL

[7005


DK Cable Junction Boxes Empty Boxes Accessories for Cable Junctions Boxes KOxOx

Mi TS 15 DINrai'l length 134 mm • In accordance with DIN EN 60 7i5 • for l\l.i Empty box size 1 • for equipment or terminals with dip-on mounting • with fixirg screws

Mi TS30 DIN rail length 284 mm • in accordance with DIN EN 60 7i5 • for Mi empty box sizes 1 to 8 • for equipment or terminals with dip-on mounting • with fixing screws

Mi TS45 DIN rail length 434 m m • in accordance with DIN EN 60 7i5 • for M:i empty ba< size 3 • for equipment or terminals with dip-on mounmg • with fixing screws

Mi TS 60 DIN rail length 584 m m • in accordance with DIN EN 60 7i5 • for M:i empty box. sizes 4 and 8 • for equipment or terminals with dip-on mounti'lg • with fixing screws

Mi MP 1 mounting p late W 259 x H 115 mm • material thid<ness 4 mm • for Mi -Ernpty boxes sizes i, 3, 4 • with fixing screws

M i MP 2 mounting plate W 265 x H 265 mm

• material thickness 4 mm • for Mi-Empty boxes sizes 2 to 8 • with fixing screws

Ca ll for a Quote! (800) 677·8942 I (303) 680·5159


~~43$==tf •

35

l:oJ Ill a u > c w


iol Ill C% u > c Ill

36


- .. --

MiMP 3 Mounting plate W 265 x H 415 mm

• material thickness 4 mm • for Mi-Empty boxes sizes 3, 4 • with fixing scre~~YS

MiMP 4 Mounting plate W 265 x H 565 mm

• material thickness 4 mm • for Mi-Empty boxes sizes .6 , 8 • with fixing screiiYS

Mi ZS 30 Hinge for lids

• for empty boxes K Oxxx • with lamellar plugs fCl( 2lid fixing tubes • 1he lid keeps permanen11y connected to the box

Mi PL 2 Sealing cap • 2 sealing caps for converting the lid fasteners

Mi SR4 Conversion set for manual operation on tool operation

• 4 fastening COIIerS

MiSN4 Conversion set for converting l id fasteners f rom tool to manual operation • 4 manual actuators

Ca ll for a Quote! (800) 677·8942 I (303) 680·5159


ro



t I

Mi DV 01 Locking dev,ice insertion

• only in connection with Mi PL 2, Mi SR 4 or Mi SN 4

Mi ZS 11 ud lock with locking device I • Is being used instead o f fasteners for hand or tool operation in

order to prevent unauthorised opening of the lids • consisting of: cylinder lock, keys, locking device i"lsertion, dust

c011er

Mi ZS 12 Lid lock with locking device II

• Is being used instead o f fasteners for hand or tool operation in order to prevent unauthorised opening of the lids

• consisting of: cylinder lock, keys, locking device ilsertion, dust c011er

Mi DR 04 L id fastener for tool operation triangle 8 mm • is used instead of fasteners for hand- or tool operation. in order to

make unauthorized opening of lids more difficult • 41ocking devices wi1h triangle 8 mm and key

0 51 Triangular key 8 mm

Mi AL40 4 stainless steel external brackets • for external fixing of enclosures

Ca ll for a Quote! (800) 677·8942 I (303) 680·5159


37

w VI Cl u > c w

Cable Entry via Metric Knockouts - Hi-Tech Controls · Cable Entry via Metric Knockouts • Plenty...

Documents

Transcript of Cable Entry via Metric Knockouts - Hi-Tech Controls · Cable Entry via Metric Knockouts • Plenty...