Building wire
-
Upload
stephanie-sanchez -
Category
Documents
-
view
215 -
download
1
description
Transcript of Building wire
6
Description
Soft copper conductor, PVC insulated.
Construction
ConductorSolid or compressed strand soft copper
InsulationPolyvinyl Chloride (PVC 60° C), flame retardant
Options
Available upon request, TW-LS (Low Smoke emission), TW-SR(Sunlight Resistant) and with insulation Gasoline and Oil resistantG&O (different types and grades of resistance to oil and gasoline)
Characteristics
Operating TemperatureDry Locations 60° C.Wet Locations 60° C
Operating Voltage600 V.
Applications
TW cables and wires are used generally in building wiring, feederand branch circuits, and internal secondary industrial distribution.
Installation: in ducts tubing and boards; raceways for 1/0 AWG andgreater sizes, according to NEC and NTC 2050 standards.
Wire and Cable Type TWThermoplastic Insulation, Suitable for Wet Locations
7
Standards
CENTELSA TW wires and cables are manufactured under the followingstandards:
ASTM B3, NTC 359. Soft copper wire.ASTM B8, NTC 307. Concentric Lay Stranded copper conductors.ASTM B787. 19 Wire Combination Unilay Stranded Copper conductors forsubsequent insulation.UL 1581, NTC-3203. Reference Standard for Electrical Wires, Cables andFlexible Cords.UL 83, NTC-1332. Thermoplastic insulated Wires and Cables.
Certifications
CENTELSA TW Wires and Cables are certified by:
UL 83. File E206516.ICONTEC (Colombia). Standard NTC 1332.CIDET (Colombia). Cert. No. 00406.LAPEM (Mexico). CFE E0000-06.FONDONORMA (Venezuela). NORVEN 364 (Standard COVENIN 397).
ColorsSizes 14 to 8 AWG: black, white, red, green, yellow, blue. Sizes 4 AWG andgreater: black.
PackagingSizes 14 to 8 AWG: 100 m spools covered with plastic thermo pack, in corrugatedcarton boxes. Sizes 6 to 4/0 AWG: 1000 m reels.Sizes 250 to 500 kcmil: 500 m reels.
Note: Other configurations, sizes, colors and length not specified herein areavailable upon request.
Wire and Cable Type TW 600V (International System Units)Thermoplastic Insulation, Suitable for Wet Locations (60°C)
Standard: UL 83, NTC 1332. Thermoplastic insulated Wires and Cables.
Notes: 1. DC resistance calculated based on a 17.241 ohm-mm2/km resistivity for cooper.2. 60°C conductor temperature, 30°C ambient temperature, According to NEC and NTC 2050, for sizes 14 12 and 10 AWG overload protection must be 15, 20 and 30 A.3. One single conductor at free air at 30°C ambient temperature.4. No more than three current carrying conductors in a duct or in direct burial, 30°C ambient temperature.5. According to NEC NTC 2050 the minimun size for use in Tray Cables must be 1/0 AWG for phase conductors, and 4 AWG for grounding
conductors.6. Data herein indicated are approximated and are subject to normal manuracturing tolerances.
STRANDSNo.
SIZEAWG /kcmil
STRANDINGCLASS
SECTION(mm2)
CONDUCTORDIAMETER
(mm)
INSULATIONTHICKNESS
(mm)
INSULATIONDIAMETER
(mm)
DCRESISTANCE
AT 20°C 1(ohm/km)
APPROX.TOTAL
WEIGTH (kg/km)
AMPACITY 2
(A) 3AMPACITY 2
(A) 4
1.632.052.593.264.125.191.792.252.853.594.525.717.207.908.889.96
11.1912.5614.1815.5216.7817.9420.0422.0023.7524.5925.3926.9428.38
1111117777777
19191919193737373737616161616161
141210
864
141210
86421
1/02/03/04/0
250300350400500600700750800900
1000
SolidSolidSolidSolidSolidSolid
BBBBBBBBBBBBBBBBBBBBBBB
2.083.315.268.37
13.3021.15
2.083.315.268.37
13.3021.1533.6342.4153.4867.4385.03107.2126.7152.0177.3202.7253.4304.0354.7380.0405.4456.0506.7
3.233.654.195.647.298.363.393.854.455.977.698.88
10.3712.0813.0614.1515.3716.7519.1520.4921.7522.9125.0127.7529.5030.3531.1532.7034.14
0.760.760.761.141.521.520.760.760.761.141.521.521.522.032.032.032.032.032.412.412.412.412.412.792.792.792.792.792.79
27405999
160237
294262
104168250377484595733906
112313481595184120862573310235873829407145545035
2530406080
1052530406080
105140165195225260300340375420455515575630655680730780
8.295.213.282.061.30
0.8158.455.313.342.101.32
0.8310.5230.4150.3290.2610.2070.1640.1390.116
0.09920.08680.06940.05780.04960.04630.04340.03860.0347
20253040557020253040557095
110125145165195215240260280320355385400410435455
8
Notes: 1. DC resistance calculated based on a 10.371 ohm-cmil/ft resistivity for cooper.2. 60°C conductor temperature, 30°C ambient temperature, According to NEC and NTC 2050, for sizes 14 12 and 10 AWG overload protection must be 15, 20 and 30 A.3. One single conductor at free air at 30°C ambient temperature.4. No more than three current carrying conductors in a duct or in direct burial, 30°C ambient temperature.5. According to NEC NTC 2050 the minimun size for use in Tray Cables must be 1/0 AWG for phase conductors, and 4 AWG for grounding
conductors.6. Data herein indicated are approximated and are subject to normal manuracturing tolerances.
Wire and Cable Type TW 600VThermoplastic Insulation, Suitable for Wet Locations (60°C)
Standard: UL 83, NTC 1332. Thermoplastic insulated Wires and Cables.
6481
102128162204
7089
112141178225283311349392440494558611661706789866935968
100010611117
1111117777777
19191919193737373737616161616161
141210
864
141210
86421
1/02/03/04/0
250300350400500600700750800900
1000
SolidSolidSolidSolidSolidSolid
BBBBBBBBBBBBBBBBBBBBBBB
0.003230.005130.00815
0.01300.02060.0328
0.003230.005130.00815
0.01300.02060.03280.05210.06570.0829
0.1050.1320.1660.1960.2360.2750.3140.3930.4710.5500.5890.6280.7070.785
127144165222287329133152175235303349408476514557605659754807856902985
109311621195122612871344
3030304560603030304560606080808080809595959595
110110110110110110
18274066
107159
19284270
113168253325400493609755906
1072123714021729208424112573273630603384
2530406080
1052530406080
105140165195225260300340375420455515575630655680730780
2.531.591.00
0.6280.3950.248
2.581.621.02
0.6410.4030.2530.1590.1260.100
0.07950.06300.05000.04230.03530.03020.02640.02120.01760.01510.01410.01320.01180.0106
20253040557020253040557095
110125145165195215240260280320355385400410435455
9
STRANDSNo.
SIZEAWG /kcmil
STRANDINGCLASS
SECTION(sq inches)
CONDUCTORDIAMETER
(mils)
INSULATIONTHICKNESS
(mils)
INSULATIONDIAMETER
(mils)
DCRESISTANCE
AT 20°C 1(ohm/kft)
APPROX.TOTAL
WEIGTH (pound/kft)
AMPACITY 2
(A) 3AMPACITY 2
(A) 4
10
Description
Soft copper conductor, PVC insulated.
Construction
ConductorSolid or compressed strand soft copper
InsulationPolyvinyl Chloride (PVC 75° C), flame retardant
Options
Available upon request, THW-LS (Low Smoke emission), THW-SR(Sunlight Resistant) and with insulation Gasoline and Oil resistantG&O (different types and grades of resistance to oil and gasoline)
Characteristics
Operating TemperatureDry Locations 75° C.Wet Locations 75° C
Operating Voltage600 V.
Applications
THW cables and wires are used generally in building wiring, feederand branch circuits, and internal secondary industrial distribution.
Installation: in ducts tubing and boards; raceways for 1/0 AWG andgreater sizes, according to NEC and NTC 2050 standards.Standards
Wire and Cable Type THWThermoplastic Insulation, Heat Resistant (75°C), Suitable for Wet Locations
11
CENTELSA THW wires and cables are manufactured under the followingstandards:
Satndards
ASTM B3, NTC 359. Soft copper wire.ASTM B8, NTC 307. Concentric Lay Stranded copper conductors.ASTM B787. 19 Wire Combination Unilay Stranded Copper conductors forsubsequent insulationUL 1581, NTC-3203. Reference Standard for Electrical Wires, Cables andFlexible Cords.UL 83, NTC-1332. Thermoplastic insulated Wires and Cables.
Certifications
CENTELSA THW Wires and Cables are certified by:
UL 83. File E206516.ICONTEC (Colombia). Standard NTC 1332.CIDET (Colombia). Cert. No. 00406.LAPEM (Mexico). CFE E0000-03.FONDONORMA (Venezuela). NORVEN 364 (Standard COVENIN 397).
ColorsSizes 14 to 6 AWG: black, white, red, green, yellow, blue. Sizes 4 AWG andgreater: black
PackagingSizes 14 to 10 AWG: 100 m spools covered with plastic thermo pack, incorrugated carton boxes. Sizes 8 and 6: 2000 m reels, Sizes 4 to 4/0 AWG:1000 m reels. Sizes 250 to 500 kcmil: 500 m reels.
Note: Other configurations, sizes, colors and length not specified herein areavailable upon request.
12
Wire and Cable Type THW (International System Units)Thermoplastic Insulation, Heat Resistant (75°C), Suitable for Wet Locations
Standard: UL 83, NTC 1332. Thermoplastic insulated Wires and Cables
Notes: 1. DC resistance calculated based on a 17.241 ohm-mm2/km resistivity for cooper.2. 75°C conductor temperature, 30°C ambient temperature, According to NEC and NTC 2050, for sizes 14 12 and 10 AWG overload
protection must be 15, 20 and 30 A.3. One single conductor at free air at 30°C ambient temperature.4. No more than three current carrying conductors in a duct or in direct burial, 30°C ambient temperature.5. According to NEC NTC 2050 the minimun size for use in Tray Cables must be 1/0 AWG for phase conductors, and 4 AWG for grounding conductors.6. Data herein indicated are approximated and are subject to normal manuracturing tolerances.
1.632.052.593.264.125.191.792.252.853.594.525.717.207.908.889.96
11.1912.5614.1815.5216.7817.9420.0422.0023.7524.5925.3926.9428.38
1111117777777
19191919193737373737616161616161
141210
864
141210
86421
1/02/03/04/0
250300350400500600700750800900
1000
SolidSolidSolidSolidSolidSolid
BBBBBBBBBBBBBBBBBBBBBBB
2.083.315.268.37
13.3021.15
2.083.315.268.37
13.3021.1533.6342.4153.4867.4385.03107.2126.7152.0177.3202.7253.4304.0354.7380.0405.4456.0506.7
3.233.654.195.647.298.363.393.854.455.977.698.88
10.3712.0813.0614.1515.3716.7519.1520.4921.7522.9125.0127.7529.5030.3531.1532.7034.14
0.760.760.761.141.521.520.760.760.761.141.521.521.522.032.032.032.032.032.412.412.412.412.412.792.792.792.792.792.79
27395997
157235
284162
102165247373479589727899
111513371583182820722558308335673808405045315011
3035507095
1253035507095
125170195230265310360405455505545620690755785815870935
8.295.213.282.061.30
0.8158.455.313.342.101.32
0.8310.5230.4150.3290.2610.2070.1640.1390.116
0.09920.08680.06940.05780.04960.04630.04340.03860.0347
202535506585202535506585
115130150175200230255285310335380420460475490520545
STRANDSNo.
SIZEAWG /kcmil
STRANDINGCLASS
SECTION(mm2)
CONDUCTORDIAMETER
(mm)
INSULATIONTHICKNESS
(mm)
INSULATIONDIAMETER
(mm)
DCRESISTANCE
AT 20°C 1(ohm/km)
APPROX.TOTAL
WEIGTH (kg/km)
AMPACITY 2
(A) 3AMPACITY 2
(A) 4
13
Notes: 1. DC resistance calculated based on a 10.371 ohm-cmil/ft resistivity for cooper.2. 75°C conductor temperature, 30°C ambient temperature, According to NEC and NTC 2050, for sizes 14 12 and 10 AWG overload protection must be 15, 20 and 30 A.3. One single conductor at free air at 30°C ambient temperature.4. No more than three current carrying conductors in a duct or in direct burial, 30°C ambient temperature.5. According to NEC NTC 2050 the minimun size for use in Tray Cables must be 1/0 AWG for phase conductors, and 4 AWG for grounding
conductors.6. Data herein indicated are approximated and are subject to normal manuracturing tolerances.
6481
102128162204
7089
112141178225283311349392440494558611661706789866935968
100010611117
1111117777777
19191919193737373737616161616161
141210
864
141210
86421
1/02/03/04/0
250300350400500600700750800900
1000
SolidSolidSolidSolidSolidSolid
BBBBBBBBBBBBBBBBBBBBBBB
0.003230.005130.00815
0.01300.02060.0328
0.003230.005130.00815
0.01300.02060.03280.05210.06570.0829
0.1050.1320.1660.1960.2360.2750.3140.3930.4710.5500.5890.6280.7070.785
127144165222287329133152175235303349408476514557605659754807856902985
109311621195122612871344
3030304560603030304560606080808080809595959595
110110110110110110
18263965
106158
19284169
111166250322396488604749899
1064122913931719207223972559272130453368
3035507095
1253035507095
125170195230265310360405455505545620690755785815870935
2.531.591.00
0.6280.3950.248
2.581.621.02
0.6410.4030.2530.1590.1260.100
0.07950.06300.05000.04230.03530.03020.02640.02120.01760.01510.01410.01320.01180.0106
202535506585202535506585
115130150175200230255285310335380420460475490520545
Wire and Cable Type THWThermoplastic Insulation, Heat Resistant (75°C), Suitable for Wet Locations
Standard: UL 83, NTC 1332. Thermoplastic insulated Wires and Cables
STRANDSNo.
SIZEAWG /kcmil
STRANDINGCLASS
SECTION(sq inches)
CONDUCTORDIAMETER
(mils)
INSULATIONTHICKNESS
(mils)
INSULATIONDIAMETER
(mils)
DCRESISTANCE
AT 20°C 1(ohm/kft)
APPROX.TOTAL
WEIGTH (pound/kft)
AMPACITY 2
(A) 3AMPACITY 2
(A) 4
Description
Soft copper conductor, PVC-LS (Low smoke emissions) insulated.
Construction
ConductorSolid or compressed strand soft copper
InsulationTHW-LS: Polyvinyl Chloride (PVC 75°C), flame retardant and lowsmoke emissions (LS).THHW-LS: Polyvinyl Chloride (PVC 90°C), flame retardant and lowsmoke emissions (LS).
Characteristics
Operating TemperatureDry Locations THHW-LS 90°C, THW-LS 75°CWet Locations THHW-LS 75°C, THW-LS 75°C
Operating Voltage600 V.
Applications
THW-LS and THHW-LS cables and wires are used generally in buildingwiring, feeder and branch circuits, and internal secondary industrialdistribution. In installations what require special security conditions infire case.
In fire case, THS-LS and THHW-LS have an excellent performanceregarding low smoke emissions, darkness, toxicity, and corrosivesmoke.
Wire and Cable Type THW-LS and THHW-LSThermoplastic Insulation, Heat Resistant (75°C), Suitable for Wet Locations, Low SmokeThermoplastic Insulation, High Heat Resistant (90°C), Suitable for Wet Location (75°C), Low Smoke
14
Installation: in ducts tubing and boards; raceways for 1/0 AWG and greatersizes, according to NEC and NTC 2050 standards.
Standards
CENTELSA THW-LS and THHW-LS wires and cables are manufactured underthe following standards:
ASTM B3, NTC 359. Soft copper wire.ASTM B8, NTC 307. Concentric Lay Stranded copper conductors.ASTM B787. 19 Wire Combination Unilay Stranded Copper conductors forsubsequent insulationUL 1581, NTC-3203. Reference Standard for Electrical Wires, Cables andFlexible Cords.UL 83, NTC-1332. Thermoplastic insulated Wires and Cables.
Certifications
CENTELSA THW-LS and RHHW-LS Wires and Cables are certified by:
ICONTEC (Colombia). Standard NTC 1332.LAPEM (Mexico). CFE E0000-03.FONDONORMA (Venezuela). NORVEN 364 (Standard COVENIN 397).ANCE (Mexico) NOM 063.
ColorsSizes 14 to 6 AWG: black, white, red, green, yellow, blue. Sizes 4 AWG andgreater: black
PackagingSizes 14 to 10 AWG: 100 m spools covered with plastic thermo pack, incorrugated carton boxes. Sizes 8 and 6: 2000 m reels, Sizes 4 to 4/0 AWG:1000 m reels. Sizes 250 to 500 kcmil: 500 m reels.
Note: Other configurations, sizes, colors and length not specified herein areavailable upon request.
15
16
Notes: 1. DC resistance calculated based on a 17.241 ohm-mm2/km resistivity for cooper.2. No more than three current carrying conductors in a duct or in direct burial, 30°C ambient temperature, according to NEC and NTC 2050, for sizes 14 12 and 10 AWG overload protection must be 15, 20 and 30 A.3. According to NEC NTC 2050 the minimun size for use in Tray Cables must be 1/0 AWG for phase conductors, and 4 AWG for grounding conductors.4. Data herein indicated are approximated and are subject to normal manuracturing tolerances.
1.632.052.593.264.125.191.752.212.783.514.425.587.047.908.889.96
11.1912.5614.1815.5216.7817.9420.0422.0023.7524.5925.3926.9428.38
111111
1919191919191919191919193737373737616161616161
141210
864
141210
86421
1/02/03/04/0
250300350400500600700750800900
1000
SolidSolidSolidSolidSolidSolid
CCCCCCCBBBBBBBBBBBBBBBB
2.083.315.268.37
13.3021.15
2.083.315.268.37
13.3021.1533.6342.4153.4867.4385.03107.2126.7152.0177.3202.7253.4304.0354.7380.0405.4456.0506.7
3.233.654.195.647.298.363.353.814.385.897.598.75
10.2112.0813.0614.1515.3716.7519.1520.4921.7522.9125.0127.7529.5030.3531.1532.7034.14
0.760.760.761.141.521.520.760.760.761.141.521.521.522.032.032.032.032.032.412.412.412.412.412.792.792.792.792.792.79
27405999
160237
284161
102166246371484595734907
112313481595184120862573310235883830407145545036
202535506585202535506585
115130150175200230255285310335380420460475490520545
8.295.213.282.061.30
0.8158.455.313.342.101.32
0.8310.5230.4150.3290.2610.2070.1640.1390.116
0.09920.08680.06940.05780.04960.04630.04340.03860.0347
253040557595253040557595
130150170195225260290320350380430475520535555585615
Wire and Cable Types THW-LS y THHW-LS 600V(International System Units)Thermoplastic Insulation, Heat Resistant (75°C), Suitable for Wet Locations, Low SmokeThermoplastic Insulation, High Heat Resistant (90°C), Suitable for Wet Locations (75°C), Low Smoke
Standard: UL 83, NTC 1332. Thermoplastic insulated Wires and Cables
STRANDSNo.
SIZEAWG /kcmil
STRANDINGCLASS
SECTION(mm2)
CONDUCTORDIAMETER
(mm)
INSULATIONTHICKNESS
(mm)
INSULATIONDIAMETER
(mm)
DCRESISTANCE
AT 20°C 1(ohm/km)
APPROX.TOTAL
WEIGTH (kg/km)
AMPACITY 2
75°C
(A) 3
AMPACITY 2
75°C
(A) 4
17
Notes: 1. DC resistance calculated based on a 10.371 ohm-cmil/ft resistivity for cooper.2. No more than three current carrying conductors in a duct or in direct burial, 30°C ambient temperature, according to NEC and NTC 2050, for sizes 14 12 and 10 AWG overload protection must be 15, 20 and 30 A.3. According to NEC NTC 2050 the minimun size for use in Tray Cables must be 1/0 AWG for phase conductors, and 4 AWG for grounding conductors.4. Data herein indicated are approximated and are subject to normal manuracturing tolerances.
6481
102128162204
6987
110138174220277311349392440494558611661706789866935968
100010611117
111111
1919191919191919191919193737373737616161616161
141210
864
141210
86421
1/02/03/04/0
250300350400500600700750800900
1000
SolidSolidSolidSolidSolidSolid
CCCCCCCBBBBBBBBBBBBBBBB
0.003230.005130.00815
0.01300.02060.0328
0.003230.005130.00815
0.01300.02060.03280.05210.06570.0829
0.1050.1320.1660.1960.2360.2750.3140.3930.4710.5500.5890.6280.7070.785
127144165222287329132150173232299344402476514557605659754807856902985
109311621195122612871344
3030304560603030304560606080808080809595959595
110110110110110110
18274066
107159
19284169
111165249326400493609755906
1072123714021729208524112574273630613384
202535506585202535506585
115130150175200230255285310335380420460475490520545
2.531.591.00
0.6280.3950.248
2.581.621.02
0.6410.4030.2530.1590.1260.100
0.07950.06300.05000.04230.03530.03020.02640.02120.01760.01510.01410.01320.01180.0106
253040557595253040557595
130150170195225260290320350380430475520535555585615
Wire and Cable Types THW-LS y THHW-LS 600VThermoplastic Insulation, Heat Resistant (75°C), Suitable for Wet Locations, Low SmokeThermoplastic Insulation, High Heat Resistant (90°C), Suitable for Wet Locations (75°C), Low Smoke
Standard: UL 83, NTC 1332. Thermoplastic insulated Wires and Cables
STRANDSNo.
SIZEAWG /kcmil
STRANDINGCLASS
SECTION(sq inches)
CONDUCTORDIAMETER
(mils)
INSULATIONTHICKNESS
(mils)
INSULATIONDIAMETER
(mils)
DC RESISTANCEAT 20°C 1(ohm/kft)
APPROX.TOTAL
WEIGTH (pound/kft)
AMPACITY 2
75°C(A) 3
AMPACITY 2
90°C(A) 4
18
Wire and Cable Type THHN/THWN and THWN-2Thermoplastic Insulation, High Heat Resistant (90°C), Dry Locations only, Nylon JacketThermoplastic Insulation, Heat Resistant (75°C), Suitable for Wet Locations, Nylon JacketThermoplastic Insulation, Heat Resistant (90°C), Suitable for Wet Locations, Nylon Jacket,2: 90°C Wet and Dry Locations
Description
Soft copper conductor, PVC insulated and with a Nylon covering
Construction
ConductorSolid or compressed strand soft copper
InsulationPolyvinyl Chloride (PVC 90° C), flame retardant, for THHN and THWN-2Polyvinyl Chloride (PVC 75° C), flame retardant, for THWN
JacketAbrasion resistant Nylon
Options
Available upon request, LS insulation (Low Smoke emission), SRSunlight Resistant insulation and with insulation Gasoline and Oilresistant G&O (different types and grades of resistance to oil andgasoline)
Characteristics
Operating TemperatureDry Locations, THHN and THWN-2: 90°C.Wet Locations, THWN and THHN: 75°C.Wet Locations, THWN-2: 90°C.
19
Operating Voltage600 V.
Applications
THHN/THWN and THWN-2 cables and wires are used generally in buildingwiring, feeder and branch circuits, and internal secondary industrial distribution.Special for locations with abrasive environment, oil, grease, gasoline and otherchemical agents contaminated ambient.
Installation: in ducts tubing and boards; raceways for 1/0 AWG and greatersizes, according to NEC and NTC 2050 standards.
Standards
CENTELSA THHN/THWN and THWN-2 wires and cables are manufacturedunder the following standards:
ASTM B3, NTC 359. Soft copper wire.ASTM B8, NTC 307. Concentric Lay Stranded copper conductors.ASTM B787. 19 Wire Combination Unilay Stranded Copper conductors forsubsequent insulationUL 1581, NTC-3203. Reference Standard for Electrical Wires, Cables andFlexible Cords.UL 83, NTC-1332. Thermoplastic insulated Wires and Cables.
Certifications
CENTELSA THHN/THWN and THWN-2 Wires and Cables are certified by:
UL 83. File E206516.ICONTEC (Colombia). Standard NTC 1332.CIDET (Colombia). Cert. No. 00406.ANCE (Mexico) NOM 063.
ColorsSizes 14 to 2 AWG: black, white, red, green, yellow, blue. Sizes 1 AWG andgreater: black
PackagingSizes 14 to 10 AWG: 100 m spools covered with plastic thermo pack, incorrugated carton boxes. Sizes 8 and 6: 2000 m reels, Sizes 4 to 4/0 AWG:1000 m reels. Sizes 250 to 500 kcmil: 500 m reels.
Note: Other configurations, sizes, colors and length not specified herein areavailable upon request.
Notes: 1. DC resistance calculated based on a 17.241 ohm-mm2/km resistivity for cooper.2. 90°C conductor temperature, 30°C ambient temperature, According to NEC and NTC 2050, for sizes 14 12 and 10 AWG overload protection must be 15, 20 and 30 A.3. One single conductor at free air at 30°C ambient temperature.4. No more than three current carrying conductors in a duct or in direct burial, 30°C ambient temperature.5. According to NEC NTC 2050 the minimun size for use in Tray Cables must be 1/0 AWG for phase conductors, and 4 AWG for grounding conductors.6. Data herein indicated are approximated and are subject to normal manuracturing tolerances.
20
Wire and Cable Type THHN/THWN and THWN-2 600V(International System Units)Thermoplastic Insulation, High Heat Resistant (90°C), Dry Locations only, Nylon JacketThermoplastic Insulation, Heat Resistant (75°C), Suitable for Wet Locations, Nylon JacketThermoplastic Insulation, Heat Resistant (90°C), Suitable for Wet Locations, Nylon Jacket,2: 90°C Wet and Dry Locations
Standard: UL 83, NTC 1332. Thermoplastic insulated Wires and Cables.
1.631.791.752.052.252.212.592.852.783.263.593.514.124.524.425.715.587.207.047.908.188.889.189.96
10.3111.1911.5812.5613.0014.1814.1815.5215.5216.7816.7817.9417.9420.0420.0422.0022.0023.7523.7524.5924.5925.3925.3926.9426.9428.3828.38
17
1917
1917
1917
1917
197
197
191937193719371937193737613761376137613761619161916191619161916191
141414121212101010
888666442211
1/01/02/02/03/03/04/04/0
250250300300350350400400500500600600700700750750800800900900
10001000
SolidBC
SolidBC
SolidBC
SolidBC
SolidBCBCBCBCBCBCBCBCBCBCBCBCBCBCBCBCBCBCBC
2.082.082.083.313.313.315.265.265.268.378.378.37
13.3013.3013.3021.1521.1533.6333.6342.4142.4153.4853.4867.4367.4385.0385.03107.2107.2126.7126.7152.0152.0177.3177.3202.7202.7253.4253.4304.0304.0354.7354.7380.0380.0405.4405.4456.0456.0506.7506.7
2.732.892.853.153.363.313.954.214.145.195.525.446.056.456.358.228.099.719.55
11.0011.2811.9812.2813.0713.4114.2914.6815.6616.1017.8717.8719.2219.2220.4820.4821.6321.6323.7423.7426.2926.2928.0428.0428.8828.8829.6829.6831.2331.2332.6832.68
0.100.100.100.100.100.100.100.100.100.130.130.130.130.130.130.150.150.150.150.180.180.180.180.180.180.180.180.180.180.200.200.200.200.200.200.200.200.200.200.230.230.230.230.230.230.230.230.230.230.230.23
242524353737565958929795
139146144234231358353452453560561695696864865
107710781286128415291526177017672011200724912486299829913476346937153707395439454431442149064895
353535404040555555808080
105105105140140190190220220260260300300350350405405455455505505570570615615700700780780855855885885920920985985
10551055
8.298.458.455.215.315.313.283.343.342.062.102.101.301.321.32
0.8310.8310.5230.5230.4150.4150.3290.3290.2610.2610.2070.2070.1640.1640.1390.1390.1160.116
0.09920.09920.08680.08680.06940.06940.05780.05780.04960.04960.04630.04630.04340.04340.03860.03860.03470.0347
2525253030304040405555557575759595
130130150150170170195195225225260260290290320320350350380380430430475475520520535535555555585585615615
2.472.632.592.893.093.053.693.943.884.865.195.115.726.126.027.827.699.319.15
10.5410.8211.5211.8212.6112.9513.8314.2215.2015.6417.3517.3518.6918.6919.9519.9521.1121.1123.2123.2125.7025.7027.4527.4528.2928.2929.0929.0930.6430.6432.0832.08
0.380.380.380.380.380.380.510.510.510.760.760.760.760.760.761.021.021.021.021.271.271.271.271.271.271.271.271.271.271.521.521.521.521.521.521.521.521.521.521.781.781.781.781.781.781.781.781.781.781.781.78
STRANDSNo.
SIZEAWG /kcmil
STRANDINGCLASS
SECTION(mm2)
CONDUCTORDIAMETER
(mm)
INSULATIONTHICKNESS
(mm)
INSULATIONDIAMETER
(mm)
DCRESISTANCE
AT 20°C 1(ohm/km)
APPROX.TOTAL
WEIGTH (kg/km)
AMPACITY 2
(A) 3AMPACITY 2
(A) 4JACKET
THICKNESS(mm)
JACKETDIAMETER
(mm)
Wire and Cable Type THHN/THWN and THWN-2 600VThermoplastic Insulation, High Heat Resistant (90°C), Dry Locations only, Nylon JacketThermoplastic Insulation, Heat Resistant (75°C), Suitable for Wet Locations, Nylon JacketThermoplastic Insulation, Heat Resistant (90°C), Suitable for Wet Locations, Nylon Jacket,2: 90°C Wet and Dry Locations
Standard: UL 83, NTC 1332. Thermoplastic insulated Wires and Cables.
21
Notes: 1. DC resistance calculated based on a 10.371 ohm-cmil/ft resistivity for cooper.2. 90°C conductor temperature, 30°C ambient temperature, According to NEC and NTC 2050, for sizes 14 12 and 10 AWG overload protection must be 15, 20 and 30 A.3.One single conductor at free air at 30°C ambient temperature.4. No more than three current carrying conductors in a duct or in direct burial, 30°C ambient temperature.5. According to NEC NTC 2050 the minimun size for use in Tray Cables must be 1/0 AWG for phase conductors, and 4 AWG for grounding conductors.6. Data herein indicated are approximated and are subject to normal manuracturing tolerances.
647069818987
102112110128141138162178174225220283277311322349361392406440456494512558558611611661661706706789789866866935935968968
100010001061106111171117
17
1917
1917
1917
1917
197
197
191937193719371937193737613761376137613761619161916191619161916191
141414121212101010
888666442211
1/01/02/02/03/03/04/04/0
250250300300350350400400500500600600700700750750800800900900
10001000
SolidBC
SolidBC
SolidBC
SolidBC
SolidBCBCBCBCBCBCBCBCBCBCBCBCBCBCBCBCBCBCBC
0.003230.003230.003230.005130.005130.005130.008150.008150.00815
0.01300.01300.01300.02060.02060.02060.03280.03280.05210.05210.06570.06570.08290.0829
0.1050.1050.1320.1320.1660.1660.1960.1960.2360.2360.2750.2750.3140.3140.3930.3930.4710.4710.5500.5500.5890.5890.6280.6280.7070.7070.7850.785
107114112124132130155166163204217214238254250323318382376433444472484515528563578617634704704757757806806852852935935
103510351104110411371137116911691230123012861286
444444444555555666677777777778888888888999999999999
161716242525384039626564949897
157155241237304304376377467468581581724724864863
10271025119011871352134916741671201520102336233124972491265726512978297132973290
353535404040555555808080
105105105140140190190220220260260300300350350405405455455505505570570615615700700780780855855885885920920985985
10551055
2.532.582.581.591.621.621.001.021.02
0.6280.6410.6410.3950.4030.4030.2530.2530.1590.1590.1260.1260.1000.100
0.07950.07950.06300.06300.05000.05000.04230.04230.03530.03530.03020.03020.02640.02640.02120.02120.01760.01760.01510.01510.01410.01410.01320.01320.01180.01180.01060.0106
2525253030304040405555557575759595
130130150150170170195195225225260260290290320320350350380380430430475475520520535535555555585585615615
97103102114122120145155153191204201225241237308303367360415426453465496510544560598616683683736736785785831831914914
101210121081108111141114114511451206120612631263
151515151515202020303030303030404040405050505050505050505060606060606060606060707070707070707070707070
STRANDSNo.
SIZEAWG /kcmil
STRANDINGCLASS
SECTION(sq inches)
CONDUCTORDIAMETER
(mils)
INSULATIONTHICKNESS
(mils)
INSULATIONDIAMETER
(mils)
DCRESISTANCE
AT 20°C 1(ohm/kft)
APPROX.TOTAL
WEIGTH (pound /kft)
AMPACITY 2
(A) 3AMPACITY 2
(A) 4JACKET
THICKNESS(mils)
JACKETDIAMETER
(mils)
22
Description
Soft copper conductor, PVC insulated.
Construction
ConductorSolid or compressed strand soft copper
InsulationPolyvinyl Chloride (PVC 60° C), flame retardant
Characteristics
Operating TemperatureDry Locations 60° C.
Operating Voltage600 V.
Applications
TF cables and wires are used in internal board and equipment wiring.Installation: in ducts tubing and boards
Standards
CENTELSA TF wires and cables are manufactured under the followingstandards:ASTM B3, NTC 359. Soft copper wire.ASTM B8, NTC 307. Concentric Lay Stranded copper conductors.UL 62, NTC-2356. Flexible Cord and Fixture Wire.
ColorsBlack, white, red, yellow, blue.
Wire and Cable Type TFThermoplastic Insulation, Fixture Wire
23
Packaging100 m spools covered with plastic thermo pack, in corrugated carton boxes.
Note: Other configurations, sizes, colors and length not specified herein areavailable upon request.
STRANDSNo.
SIZEAWG /kcmil
STRANDINGCLASS
SECTION(mm2)
CONDUCTORDIAMETER
(mm)
INSULATIONTHICKNESS
(mm)
DIAMETEROVER
INSULATION(mm)
DCRESISTANCE
AT 20°C 1(ohm/km)
APPROX.TOTAL
WEIGTH(kg/km)
AMPACITY 2
(A) 3
1.021.291.121.42
1177
18161816
SolidSolid
BB
0.821.310.821.31
2.622.892.723.02
0.760.760.760.76
14191520
6868
20.913.221.413.4
Notes: 1. DC resistance calculated based on a 17.241 ohm-mm2/km resistivity for cooper.2. By NEC and NTC 2050 Section 402-5.3. Data herein indicated are approximated and are subject to normal manuracturing tolerances.
Wire and Cable Type TF 600V (International System Units)Thermoplastic Insulation, Fixture Wire (60°C)
Standard: UL 62, NTC 2356. Flexible Cord and Fixture Wire
40514456
1177
18161816
SolidSolid
BB
0.001280.002030.001280.00203
103114107119
30303030
9131014
6868
6.384.026.514.10
Notes: 1. DC resistance calculated based on a 10.371 ohm-cmil/ft resistivity for cooper.2. By NEC and NTC 2050 Section 402-5.3. Data herein indicated are approximated and are subject to normal manuracturing tolerances.
Wire and Cable Type TF 600VThermoplastic Insulation, Fixture Wire (60°C)
Standard: UL 62, NTC 2356. Flexible Cord and Fixture Wire
STRANDSNo.
SIZEAWG /kcmil
STRANDINGCLASS
SECTION(sq inches)
CONDUCTORDIAMETER
(mils)
INSULATIONTHICKNESS
(mils)
DIAMETEROVER
INSULATION(mils)
DCRESISTANCE
AT 20°C 1(ohm/kft)
APPROX.TOTAL
WEIGTH(pound/kft)
AMPACITY 2
(A) 3
24
Construction
ConductorSolid or compressed strand soft copperInsulationPolyvinyl Chloride (PVC 90° C), flame retardantJacketAbrasion resistant Nylon
Options
Available upon request, with insulation Gasoline and Oil resistant G&O(different types and grades of resistance to oil and gasoline)
Characteristics
Operating TemperatureDry Locations: 90°C.Wet Locations: 75°C.Operating Voltage600 V.
Applications
TFN cables and wires are used generally in internal equipment andboard wiring.Installation: in ducts tubing and boards.
Special for locations with abrasive environment, oil, grease, gasolineand other chemical agents contaminated ambient. TFN may be usedas AWM (Appliance Wiring Material) at 105°C conductor temperature.
Standards
CENTELSA TFN wires and cables are manufactured under the followingstandards:ASTM B3, NTC 359. Soft copper wire.ASTM B8, NTC 307. Concentric Lay Stranded copper conductors.ASTM B787. 19 Wire Combination Unilay Stranded Copper conductorsfor subsequent insulation
Wire and Cable Type TFNThermoplastic Insulation, Fixture Wire, Nylon Jacket
25
UL 62, NTC-2356. Flexible Cord and Fixture Wire.
ColorsBlack, white, red, yellow, blue.
Packaging100 m spools covered with plastic thermo pack, in corrugated carton boxes.
Note: Other configurations, sizes, colors and length not specified herein areavailable upon request.
Notes: 1. DC resistance calculated based on a 17.241 ohm-mm2/km resistivity for cooper.2. By NEC and NTC 2050 Section 402-5.3. Data herein indicated are approximated and are subject to normal manuracturing tolerances.
Wire and Cable Type TFN 600V (International System Units)Thermoplastic Insulation, Fixture Wire, Nylon Jacket (90°C)
Standard: UL 62, NTC-2356. Flexible Cord and Fixture Wire.
Notes: 1. DC resistance calculated based on a 10.371 ohm-cmil/ft resistivity for cooper.2. By NEC and NTC 2050 Section 402-5.3. Data herein indicated are approximated and are subject to normal manuracturing tolerances.
Wire and Cable Type TFN 600VThermoplastic Insulation, Fixture Wire, Nylon Jacket (90°C)
Standard: UL 62, NTC-2356. Flexible Cord and Fixture Wire.
DCRESISTANCE
AT 20°C 1(ohm/km)
APPROX.TOTAL
WEIGTH(kg/km)
STRANDSNo.
SIZEAWG /kcmil
STRANDINGCLASS
SECTION(mm2)
CONDUCTORDIAMETER
(mm)
INSULATIONTHICKNESS
(mm)
DIAMETEROVER
INSULATION(mm)
JACKETTHICKNESS
(mm)
DIAMETEROVER
JACKET(mm)
AMPACITY 2
(A)
1.021.291.121.42
1177
18161816
SolidSolid
BB
0.821.310.821.31
1.862.131.962.26
0.380.380.380.38
2.092.362.192.48
6868
0.100.100.100.10
11161117
20.9513.1721.3713.44
40514456
1177
18161816
SolidSolid
BB
0.001280.002030.001280.00203
73847789
15151515
82938698
6868
4444
7118
11
6.384.026.514.10
DCRESISTANCE
AT 20°C 1(ohm/kft)
APPROX.TOTAL
WEIGTH(pound/kft)
STRANDSNo.
SIZEAWG /kcmil
STRANDINGCLASS
SECTION(sq inches)
CONDUCTORDIAMETER
(mils)
INSULATIONTHICKNESS
(mils)
DIAMETEROVER
INSULATION(mils)
JACKETTHICKNESS
(mils)
DIAMETEROVER
JACKET(mils)
AMPACITY 2
(A)
26
Description
THHN circuit conductors paralleled or twisted, PVC jacket.
Construction
Circuit ConductorSolid or compressed strand soft copper
InsulationPolyvinyl Chloride (PVC 90°C), flame retardant and Nylon covered
JacketPolyvinyl Chloride (PVC 75°C), flame retardant and wet resistant.
Options
Available with or without solid soft copper grounding conductor.
Characteristics
Operating TemperatureDry Locations: 90°C.
Operating Voltage600 V.
Applications
NM-B cables and wires are used mainly in internal residential buildingwiring in branch circuits.Installation: fished in air voids in masonry block or tile walls, where isnot exposed to excessive moisture.
Wire and Cable Type NM-BNon Metallic Sheathed Cable. B: 90°C Insulation
27
Standards
CENTELSA NM-B wires and cables are manufactured under the followingstandards:
ASTM B3, NTC 359. Soft copper wire.ASTM B8, NTC 307. Concentric Lay Stranded copper conductors.UL 83, NTC-1332. Thermoplastic insulated Wires and Cables.UL 719 Non Metallic Jacket Cables.
ColorsBlack jacket for sizes 14 to 10 AWG, and black jacket for sizes 8 and greater.Circuit conductors are color code identified, 2 circuits black-white 3 circuitsblack-white-red.
Packaging100 m spools covered with plastic thermo pack.
Note: Other configurations, sizes, colors and length not specified herein areavailable upon request.
28
Wires and Cables Type NM-B 600V(International System Units)Non Metallic Sheathed Cable. B: 90°C Insulation
Standard: UL 719. Non Metallic Jacket Cables
Notes: 1. DC resistance calculated based on a 17.241 ohm-mm2/km resistivity for cooper.2. No more than three current carrying conductors in a duct or in direct burial, 90°C conductor temperatur (By NEC and NTC 2050 section
33626) and 30°C ambient temperature, according to NEC and NTC 2050, for sizes 14 12 and 10 AWG overload protection must be 15, 20 and 30 A.
3. Data herein indicated are approximated and are subject to normal manuracturing tolerances
(THHN)CIRCUIT
CONDUCTORS
CONDUCTORDIAMETER
(mm)
STRANDSNo.
SIZEAWG /kcmil
STRANDINGCLASS
SECTION(mm2)
(THHN)DIAMETER
CONDUCTORS
SOLIDGROUNDING CONDUCTOR
SIZE (AWG)
GROUNDINGCONDUCTOR
DIAMETER(mm)
DCRESISTANCE
AT 20°C 1(ohm/km)
APPROX.TOTAL
WEIGTH (kg/km)
JACKETDIMENSIONS
(mm)
AMPACITY 2
(A)JACKET
THICKNESS(mm)
1.632.052.593.594.525.717.201.632.052.593.594.525.717.201.632.052.593.594.525.717.201.632.052.593.594.525.717.20
1117777111777711177771117777
141210
8642
141210
8642
141210
8642
141210
8642
SolidSolidSolid
BBBB
SolidSolidSolid
BBBB
SolidSolidSolid
BBBB
SolidSolidSolid
BBBB
2.083.315.268.37
13.3021.1533.63
2.083.315.268.37
13.3021.1533.63
2.083.315.268.37
13.3021.1533.63
2.083.315.268.37
13.3021.1533.63
0.760.760.760.760.760.760.760.760.760.760.760.760.760.760.760.760.760.760.760.760.760.760.760.760.760.760.760.76
-------
1.632.052.592.592.593.263.26
-------
1.632.052.592.592.593.263.26
8.295.213.282.101.320.830.528.295.213.282.101.32
0.8310.523
8.455.313.342.141.35
0.8480.533
8.455.313.342.141.35
0.8480.533
6998
143242348534793
90127192281386600856
97136206344499780
1171126179269406567881
1274
20253040557095202530405570952025304055709520253040557095
-------
1412101010
88-------
1412101010
88
2.693.123.915.486.418.169.652.693.123.915.486.418.169.652.693.123.915.486.418.169.652.693.123.915.486.418.169.65
2222222222222233333333333333
8.929.77
11.1013.9715.8318.7721.75
8.929.89
12.0115.1417.0021.1924.17
7.408.32
10.0314.4015.4119.1922.40
8.619.89
12.0115.1417.0021.1924.17
4.29 4.72 5.51 7.38 8.3110.0611.55 4.29 4.72 5.51 7.088.01
9.7611.25
xxxxxxxxxxxxxx
29
Wires and Cables Type NM-B 600VNon Metallic Sheathed Cable. B: 90°C Insulation
Standard: UL 719. Non Metallic Jacket Cables
Notes: 1. DC resistance calculated based on a 10.371 ohm-cmil/ft resistivity for cooper.2. No more than three current carrying conductors in a duct or in direct burial, 90°C conductor temperatur (By NEC and NTC 2050 section
33626) and 30°C ambient temperature, according to NEC and NTC 2050, for sizes 14 12 and 10 AWG overload protection must be 15,20 and 30 A.
3. Data herein indicated are approximated and are subject to normal manuracturing tolerances
6481
102141178225283
6481
102141178225283
6481
102141178225283
6481
102141178225283
1117777111777711177771117777
141210
8642
141210
8642
141210
8642
141210
8642
SolidSolidSolid
BBBB
SolidSolidSolid
BBBB
SolidSolidSolid
BBBB
SolidSolidSolid
BBBB
0.00320.00510.00820.01300.02060.03280.05210.00320.00510.00820.01300.02060.03280.05210.00320.00510.00820.01300.02060.03280.05210.00320.00510.00820.01300.02060.03280.0521
30303030303030303030303030303030303030303030303030303030
-------
6481
102102102128128
-------
6481
102102102128128
2.531.591.00
0.6410.4030.2530.159
2.531.591.00
0.6410.4030.2530.159
2.581.621.02
0.6540.4110.2580.163
2.581.621.02
0.6540.4110.2580.163
466696
163234359533
6186
129189259403575
6592
138231336524787
85120181273381592856
20253040557095202530405570952025304055709520253040557095
-------
1412101010
88-------
1412101010
88
106123154216252321380106123154216252321380106123154216252321380106123154216252321380
2222222222222233333333333333
351385437550623739856351389473596669834952292328395567607755882339389473596669834952
169186217290327396455169186217279315384443
xxxxxxxxxxxxxx
(THHN)CIRCUIT
CONDUCTORS
CONDUCTORDIAMETER
(mm)
STRANDSNo.
SIZEAWG /kcmil
STRANDINGCLASS
SECTION(mm2)
(THHN)DIAMETER
CONDUCTORS
SOLIDGROUNDING CONDUCTOR
SIZE (AWG)
GROUNDINGCONDUCTOR
DIAMETER(mm)
DCRESISTANCE
AT 20°C 1(ohm/km)
APPROX.TOTAL
WEIGTH (kg/km)
JACKETDIMENSIONS
(mm)
AMPACITY 2
(A)JACKET
THICKNESS(mm)
Description
Aluminum conductor, PVC insulated.
Construction
ConductorSolid or compressed strand 1350-H19 aluminum
InsulationPolyvinyl Chloride (PVC 60° C), flame retardant
Options
Available upon request, TW-LS (Low Smoke emission), TW-SR (SunlightResistant) and with insulation Gasoline and Oil resistant G&O (differenttypes and grades of resistance to oil and gasoline), conductor in otheraluminum alloys
Characteristics
Operating TemperatureDry Locations 60° C.Wet Locations 60° C
Operating Voltage600 V.
Application
TW cables and wires are used generally in building wiring, feeder andbranch circuits, and internal secondary industrial distribution.
Installation: in ducts tubing and boards; raceways for 1/0 AWG andgreater sizes, according to NEC and NTC 2050 standards.
Aluminum Wire and Cable Type TWThermoplastic Insulation, Suitable for Wet Locations
30
Standards
CENTELSA TW wires and cables are manufactured under the followingstandards:
ASTM B230, NTC 360. Aluminum 1350-H19 WireASTM B231, NTC 308. Concentric-Lay-Stranded Aluminum 1350 ConductorsUL 83, NTC-1332. Thermoplastic insulated Wires and Cables.
Certifications
CENTELSA TW Wires and Cables are certified by:
UL 83. File E206516. (For 8000 series aluminum conductor)ICONTEC (Colombia). Standard NTC 1332. (For 8000 series aluminumconductor)CIDET (Colombia). Cert. No. 00408.FONDONORMA (Venezuela). NORVEN 364 (Standard COVENIN 397).
Note: Other configurations, sizes, colors and length not specified herein areavailable upon request.
31
Aluminum Wire and Cable Type TW 600V(International System Units)Thermoplastic Insulation, Suitable for Wet Locations (60°C)
Standard: UL 83, NTC 1332. Thermoplastic insulated Wires and Cables
Notes: 1. DC resistance calculated based on a 28.172 ohm-mm2/km resistivity for aluminum.2. 60°C conductor temperature, 30°C ambient temperature, According to NEC and NTC 2050, for sizes 12 and 10 AWG overload protection must be 15 and 25 A.3. One single conductor at free air at 30°C ambient temperature.4. No more than three current carrying conductors in a duct or in direct burial, 30°C ambient temperature.
5. According to NEC NTC 2050 the minimun size for use in Tray Cables must be 1/0 AWG for phase conductors, and 4 AWG for grounding conductors.6. Data herein indicated are approximated and are subject to normal manuracturing tolerances.
STRANDSNo.
SIZEAWG /kcmil
STRANDINGCLASS
SECTION(mm2)
CONDUCTORDIAMETER
(mm)
INSULATIONTHICKNESS
(mm)
DIAMETEROVER
INSULATION(mm)
DCRESISTANCE
AT 20°C 1(ohm/km)
APPROX.TOTAL
WEIGTH (kg/km)
AMPACITY 2
(A) 3AMPACITY 2
(A) 4
2.052.593.264.125.193.594.525.717.207.908.889.96
11.1912.5614.1815.5216.7817.9420.0422.0023.7524.5925.3926.9428.38
111117777
19191919193737373737616161616161
1210
86486421
1/02/03/04/0
250300350400500600700750800900
1000
SolidSolidSolidSolidSolid
BBBBBBBBBBBBBBBBBBBB
3.315.268.37
13.3021.15
8.3713.3021.1533.6342.4153.4867.4385.03107.2126.7152.0177.3202.7253.4304.0354.7380.0405.4456.0506.7
3.654.195.647.298.365.977.698.88
10.3712.0813.0614.1515.3716.7519.1520.4921.7522.9125.0127.7529.5030.3531.1532.7034.14
0.760.761.141.521.521.141.521.521.522.032.032.032.032.032.412.412.412.412.412.792.792.792.792.792.79
19274777
1065184
116164217258309371448549636722807975
118413491432151416771838
2535456080456080
110130150175200235265290330355405455500515535580625
8.515.353.372.121.333.432.161.36
0.8540.6780.5370.4260.3380.2680.2270.189
0.16200.14180.11340.09450.08100.07560.07090.06300.0567
20253040553040557585
100115130150170190210225260285310320330355375
32
Notes: 1. DC resistance calculated based on a 16.946 ohm-cmil/ft resistivity for aluminum. 2. 60°C conductor temperature, 30°C ambient temperature, According to NEC and NTC 2050, for sizes 12 and 10 AWG
overload protection must be 15 and 25 A.3. One single conductor at free air at 30°C ambient temperature.4. No more than three current carrying conductors in a duct or in direct burial, 30°C ambient temperature.5. According to NEC NTC 2050 the minimun size for use in Tray Cables must be 1/0 AWG for phase conductors, and 4 AWG for grounding conductors.6. Data herein indicated are approximated and are subject to normal manuracturing tolerances.
81102128162204141178225283311349392440494558611661706789866935968
100010611117
111117777
19191919193737373737616161616161
1210
86486421
1/02/03/04/0
250300350400500600700750800900
1000
SolidSolidSolidSolidSolid
BBBBBBBBBBBBBBBBBBBB
0.005130.00815
0.01300.02060.03280.01300.02060.03280.05210.06570.0829
0.1050.1320.1660.1960.2360.2750.3140.3930.4710.5500.5890.6280.7070.785
144165222287329235303349408476514557605659754807856902985
109311621195122612871344
30304560604560606080808080809595959595
110110110110110110
1318315271345778
110146174207249301369427485542655795907962
101711271235
2535456080456080
110130150175200235265290330355405455500515535580625
2.601.63
1.0260.6460.4061.0470.6580.4140.2600.2070.164
0.12990.10300.08170.06910.05760.04940.04320.03460.02880.02470.02300.02160.01920.0173
20253040553040557585
100115130150170190210225260285310320330355375
33
Aluminum Wire and Cable Type TW 600VThermoplastic Insulation, Suitable for Wet Locations (60°C)
Standard: UL 83, NTC 1332. Thermoplastic insulated Wires and Cables
STRANDSNo.
SIZEAWG /kcmil
STRANDINGCLASS
SECTION(sq inches)
CONDUCTORDIAMETER
(mils)
INSULATIONTHICKNESS
(mils)
DIAMETEROVER
INSULATION(mils)
DCRESISTANCE
AT 20°C 1(ohm/kft)
APPROX.TOTAL
WEIGTH (pound/kft)
AMPACITY 2
(A) 3AMPACITY 2
(A) 4
Description
Aluminum conductor, PVC insulated.
Construction
ConductorSolid or compressed strand 1350-H19 aluminum
InsulationPolyvinyl Chloride (PVC 75° C), flame retardant
Options
Available upon request, THW-LS (Low Smoke emission), THW-SR(Sunlight Resistant) and with insulation Gasoline and Oil resistantG&O (different types and grades of resistance to oil and gasoline),conductor in other aluminum alloys
Characteristics
Operating TemperatureDry Locations 75° C.Wet Locations 75° C
Operating Voltage600 V.
Applications
THW cables and wires are used generally in building wiring, feederand branch circuits, and internal secondary industrial distribution.
Installation: in ducts tubing and boards; raceways for 1/0 AWG and
Aluminum Wire and Cable Type THWThermoplastic Insulation, Heat Resistant (75°C), Suitable for Wet Locations
34
greater sizes, according to NEC and NTC 2050 standards.
Standards
CENTELSA THW wires and cables are manufactured under the followingstandards:
ASTM B230, NTC 360. Aluminum 1350-H19 WireASTM B231, NTC 308. Concentric-Lay-Stranded Aluminum 1350 ConductorsUL 83, NTC-1332. Thermoplastic insulated Wires and Cables.
Certifications
CENTELSA THW Wires and Cables are certified by:
UL 83. File E206516. (For 8000 series aluminum conductor)ICONTEC (Colombia). Standard NTC 1332. (For 8000 series aluminumconductor)CIDET (Colombia). Cert. No. 00408.FONDONORMA (Venezuela). NORVEN 364 (Standard COVENIN 397).
Note: Other configurations, sizes, colors and length not specified herein areavailable upon request.
35
36
Notes: 1. DC resistance calculated based on a 28.172 ohm-mm2/km resistivity for aluminum.2. 75°C conductor temperature, 30°C ambient temperature, According to NEC and NTC 2050, for sizes 12 and 10 AWG overload protection must be 15 and 25 A.3. One single conductor at free air at 30°C ambient temperature.4. No more than three current carrying conductors in a duct or in direct burial, 30°C ambient temperature.5. According to NEC NTC 2050 the minimun size for use in Tray Cables must be 1/0 AWG for phase conductors, and 4 AWG for grounding conductors.6. Data herein indicated are approximated and are subject to normal manuracturing tolerances.
STRANDSNo.
SIZEAWG /kcmil
STRANDINGCLASS
SECTION(mm2)
CONDUCTORDIAMATER
(mm)
INSULATIONTHICKNESS
(mm)
DIAMETEROVER
INSULATION(mm)
DCRESISTANCE
AT 20°C 1(ohm/km)
APPROX.TOTAL
WEIGTH (kg/km)
AMPACITY 2
(A) 3AMPACITY 2
(A) 4
2.052.593.264.125.193.594.525.717.208.189.18
10.3111.5813.0014.1815.5216.7817.9420.0422.0023.7524.5925.3926.9428.38
111117777
19191919193737373737616161616161
1210
86486421
1/02/03/04/0
250300350400500600700750800900
1000
SolidSolidSolidSolidSolid
BBBBBBBBBBBBBBBBBBBB
3.315.268.37
13.3021.15
8.3713.3021.1533.6342.4153.4867.4385.03107.2126.7152.0177.3202.7253.4304.0354.7380.0405.4456.0506.7
3.654.195.647.298.365.977.698.88
10.3712.3713.3614.5015.7717.1819.1520.4921.7522.9125.0127.7529.5030.3531.1532.7034.14
0.760.761.141.521.521.141.521.521.522.032.032.032.032.032.412.412.412.412.412.792.792.792.792.792.79
19264675
1045082
113161215255306368444538624709794960
116513291411149216541815
30405575
1005575
100135155180210240280315350395425485540595620645700750
8.515.353.372.121.333.432.161.36
0.8540.6780.5370.4260.3380.2680.2270.189
0.16200.14180.11340.09450.08100.07560.07090.06300.0567
203040506540506590
100120135155180205230250270310340375385395425445
Aluminum Wire and Cable Type THW(International System Units)Thermoplastic Insulation, Heat Resistant (75°C), Suitable for Wet Locations
Standard: UL 83, NTC 1332. Thermoplastic insulated Wires and Cables.
37
Notes: 1. DC resistance calculated based on a 16.946 ohm-cmil/ft resistivity for aluminum.2. 75°C conductor temperature, 30°C ambient temperature, According to NEC and NTC 2050, for sizes 12 and 10 AWG overload protection must be 15 and 25 A.3. One single conductor at free air at 30°C ambient temperature.4. No more than three current carrying conductors in a duct or in direct burial, 30°C ambient temperature.5. According to NEC NTC 2050 the minimun size for use in Tray Cables must be 1/0 AWG for phase conductors, and 4 AWG for grounding
conductors.6. Data herein indicated are approximated and are subject to normal manuracturing tolerances.
81102128162204141178225283322361406456512558611661706789866935968
100010611117
111117777
19191919193737373737616161616161
1210
86486421
1/02/03/04/0
250300350400500600700750800900
1000
SolidSolidSolidSolidSolid
BBBBBBBBBBBBBBBBBBBB
0.005130.00815
0.01300.02060.03280.01300.02060.03280.05210.06570.0829
0.1050.1320.1660.1960.2360.2750.3140.3930.4710.5500.5890.6280.7070.785
144165222287329235303349408487526571621676754807856902985
109311621195122612871344
30304560604560606080808080809595959595
110110110110110110
1317315070335576
108144172205247298362419477533645783893948
100311121219
30405575
1005575
100135155180210240280315350395425485540595620645700750
2.601.631.03
0.6460.406
1.050.6580.4140.2600.2070.1640.1300.103
0.08170.06910.05760.04940.04320.03460.02880.02470.02300.02160.01920.0173
203040506540506590
100120135155180205230250270310340375385395425445
Aluminum Wire and Cable Type THWThermoplastic Insulation, Heat Resistant (75°C), Suitable for Wet Locations
Standard: UL 83, NTC 1332. Thermoplastic insulated Wires and Cables.
STRANDSNo.
SIZEAWG /kcmil
STRANDINGCLASS
SECTION(sq inches)
CONDUCTORDIAMATER
(mils)
INSULATIONTHICKNESS
(mils)
DIAMETEROVER
INSULATION(mils)
DCRESISTANCE
AT 20°C 1(ohm/kft)
APPROX.TOTAL
WEIGTH (pound/kft)
AMPACITY 2
(A) 3AMPACITY 2
(A) 4
38
Aluminum Wire and Cable Type THHN/THWN y THWN-2Thermoplastic Insulation, High Heat Resistant (90°C), Dry Locations only, Nylon JacketThermoplastic Insulation, Heat Resistant (75°C), Suitable for Wet Locations, Nylon JacketThermoplastic Insulation, Heat Resistant (90°C), Suitable for Wet Locations, Nylon Jacket,2: 90°C Wet and Dry Locations
Description
Aluminum conductor, PVC insulated.
Construction
ConductorSolid or compressed strand 1350-H19 aluminum.
InsulationPolyvinyl Chloride (PVC 90° C), flame retardant, for THHN and THWN-2 Polyvinyl Chloride (PVC 75° C), flame retardant, for THWN.
JacketAbrasion resistant Nylon.
Options
Available upon request, LS insulation (Low Smoke emission), SRSunlight Resistant insulation and with insulation Gasoline and Oilresistant G&O (different types and grades of resistance to oil andgasoline), conductor in other aluminum alloys.
Characteristics
Operating TemperatureDry Locations, THHN and THWN-2: 90°C.
39
Wet Locations, THWN and THHN: 75°C.Wet Locations, THWN-2: 90°C.
Operating Voltage600 V.
Applications
THHN/THWN and THWN-2 cables and wires are used generally in buildingwiring, feeder and branch circuits, and internal secondary industrial distribution.Special for locations with abrasive environment, oil, grease, gasoline and otherchemical agents contaminated ambient.
Installation: in ducts tubing and boards; raceways for 1/0 AWG and greatersizes, according to NEC and NTC 2050 standards.
Standards
CENTELSA THHN/THWN and THWN-2 wires and cables are manufacturedunder the following standards:
ASTM B230, NTC 360. Aluminum 1350-H19 WireASTM B231, NTC 308. Concentric-Lay-Stranded Aluminum 1350 ConductorsUL 83, NTC-1332. Thermoplastic insulated Wires and Cables.
Certifications
CENTELSA THHN/THWN and THWN-2 Wires and Cables are certified by:
UL 83. File E206516. (For 8000 series aluminum conductor)ICONTEC (Colombia). Standard NTC 1332. (For 8000 series aluminumconductor)CIDET (Colombia). Cert. No. 00408.ANCE (Mexico) NOM 063
Note: Other configurations, sizes, colors and length not specified herein areavailable upon request.
Notes: 1. DC resistance calculated based on a 28.172 ohm-mm2/km resistivity for aluminum.2. 75°C conductor temperature, 30°C ambient temperature, According to NEC and NTC 2050, for sizes 12 and 10 AWG overload protection must be 15 and 25 A.3. One single conductor at free air at 30°C ambient temperature.4. No more than three current carrying conductors in a duct or in direct burial, 30°C ambient temperature.5. According to NEC NTC 2050 the minimun size for use in Tray Cables must be 1/0 AWG for phase conductors, and 4 AWG for grounding conductors.6. Data herein indicated are approximated and are subject to normal manuracturing tolerances.
40
STRANDSNo.
SIZEAWG /kcmil
STRANDINGCLASS
SECTION(mm2)
CONDUCTORDIAMETER
(mm)
JACKETTHICKNESS
(mm)
APPROX.TOTAL
WEIGTH (kg/km)
AMPACITY 2
(A) 3AMPACITY 2
(A) 4INSULATIONTHICKNESS
(mm)
INSULATIONOVER
DIAMETER(mm)
2.052.593.264.123.594.525.717.208.189.18
10.3111.5813.0014.1815.5216.7817.9420.0422.0023.7524.5925.3926.9428.38
11117777
19191919193737373737616161616161
1210
8686421
1/02/03/04/0
250300350400500600700750800900
1000
SolidSolidSolidSolid
BBBBBBBBBBBBBBBBBBBB
3.315.268.37
13.308.37
13.3021.1533.6342.4153.4867.4385.03107.2126.7152.0177.3202.7253.4304.0354.7380.0405.4456.0506.7
3.153.955.196.055.526.458.229.71
11.2812.2813.4114.6816.1017.8719.2220.4821.6323.7426.2928.0428.8829.6831.2332.68
0.100.100.130.130.130.130.150.150.180.180.180.180.180.200.200.200.200.200.230.230.230.230.230.23
152440574462
101146187225273332405487570651732893
108012391318139715541710
354060806080
110150175205235275315355395445480545615675700725785845
8.515.353.372.123.432.161.36
0.8540.6780.5370.4260.3380.2680.2270.1890.1620.1420.113
0.09450.08100.07560.07090.06300.0567
25354560456075
100115135150175205230255280305350385420435450480500
2.893.694.865.725.196.127.829.31
10.8211.8212.9514.2215.6417.3518.6919.9521.1123.2125.7027.4528.2929.0930.6432.08
0.380.510.760.760.760.761.021.021.271.271.271.271.271.521.521.521.521.521.781.781.781.781.781.78
Aluminum Wire and Cable Type THHN/THWNand THWN-2 600V (International System Units)Thermoplastic Insulation, High Heat Resistant (90°C), Dry Locations only, Nylon JacketThermoplastic Insulation, Heat Resistant (75°C), Suitable for Wet Locations, Nylon JacketThermoplastic Insulation, Heat Resistant (90°C), Suitable for Wet Locations, Nylon Jacket,2: 90°C Wet and Dry Locations
Standard: UL 83, NTC 1332. Thermoplastic insulated Wires and Cables.
JACKETDIAMETER
(mm)
DCRESISTANCE
AT 20°C 1(ohm/km)
41
Notes: 1. DC resistance calculated based on a 16.946 ohm-cmil/ft resistivity for aluminum.2. 75°C conductor temperature, 30°C ambient temperature, According to NEC and NTC 2050, for sizes 12 and 10 AWG overload protection must be 15 and 25 A.3. One single conductor at free air at 30°C ambient temperature.4. No more than three current carrying conductors in a duct or in direct burial, 30°C ambient temperature.5. According to NEC NTC 2050 the minimun size for use in Tray Cables must be 1/0 AWG for phase conductors, and 4 AWG for grounding conductors.6. Data herein indicated are approximated and are subject to normal manuracturing tolerances.
81102128162141178225283322361406456512558611661706789866935968
100010611117
11117777
19191919193737373737616161616161
1210
8686421
1/02/03/04/0
250300350400500600700750800900
1000
SolidSolidSolidSolid
BBBBBBBBBBBBBBBBBBBB
0.00510.00820.01300.02060.01300.02060.03280.05210.06570.0829
0.1050.1320.1660.1960.2360.2750.3140.3930.4710.5500.5890.6280.7070.785
124155204238217254323382444484528578634704757806852935
103511041137116912301286
445555667777788888999999
1016273829426898
126151183223272327383438492600726832886939
10441149
354060806080
110150175205235275315355395445480545615675700725785845
2.601.631.03
0.6461.05
0.6580.4140.2600.2070.1640.1300.103
0.08170.06910.05760.04940.04320.03460.02880.02470.02300.02160.01920.0173
25354560456075
100115135150175205230255280305350385420435450480500
114145191225204241308367426465510560616683736785831914
101210811114114512061263
152030303030404050505050506060606060707070707070
Aluminum Wire and Cable Type THHN/THWNand THWN-2 600VThermoplastic Insulation, High Heat Resistant (90°C), Dry Locations only, Nylon JacketThermoplastic Insulation, Heat Resistant (75°C), Suitable for Wet Locations, Nylon JacketThermoplastic Insulation, Heat Resistant (90°C), Suitable for Wet Locations, Nylon Jacket,2: 90°C Wet and Dry Locations
Standard: UL 83, NTC 1332. Thermoplastic insulated Wires and Cables.
STRANDSNo.
SIZEAWG /kcmil
STRANDINGCLASS
SECTION(sq inches)
CONDUCTORDIAMETER
(mils)
JACKETTHICKNESS
(mils)
DCRESISTANCE
AT 20°C 1(ohm/kft)
APPROX.TOTAL
WEIGTH (pound/kft)
AMPACITY 2
(A) 3AMPACITY 2
(A) 4INSULATIONTHICKNESS
(mils)
INSULATIONOVER
DIAMETER(mils)
JACKETDIAMETER
(mils)
Correction Factors for Ampacity
42
FOR AMBIENT TEMPERATURESOTHER THAN 30°C
For ambient temperatures other than 30°C, multiply the ampacitiesby the appropiate factor.
21-25
26-30
31-35
36-40
41-45
46-50
Temp. °C TW
1.08
1.00
0.91
0.82
0.71
0.58
THW
1.05
1.00
0.94
0.88
0.82
0.75
THHN/THWN andTHWN-2
1.04
1.00
0.96
0.91
0.87
0.82
ADJUSTMENT FACTOR FOR MORE THANTHREE CURRENT CARRYING CONDUCTORS
When the number of Current Carrying Conductors in a cable, duct or raceway exceed3, the Ampacity must be reduced as indicated.
4-6
7-9
10-20
21-30
31-40
41 and more.
NUMBER OF CURRENT-CARRYINGCONDUCTORS
FACTOR
0.80
0.70
0.50
0.45
0.40
0.35
Maximum Number of conductorsin Electrical Metallic Tubing (EMT) - Cables TW and THW
43
43332413
86432111111111----
86521111--------------
141210
86421
1/02/03/04/0
250300350400500600750800900
1000
1511853111111-----------
251914
84321111111--------
96745530181310
765433211111111
5845331811864332111111111--
254195145
814836261816131197665433322
332255190105
634734242017151210
877644333
168129
96533224171210
9765443321111
424326243135
8160443126221916131110
9765544
SIZEAWG /kcmil
NOMINAL CONDUIT DIAMETER (Inches / mm)
Maximum Number of conductorsin Electrical Metallic Tubing (EMT) - Cables THHN and THWN-2
1 1/432
1/213
141210
86421
1/02/03/04/0
250300350400500600750800900
1000
3/419
125
251
1 1/238
376
3 1/289
2 1/264
4102
SIZEAWG /kcmil
NOMINAL CONDUIT DIAMETER (Inches / mm)
6145281612
7543211111111----
1295321111-------------
221610
642111111----------
352616
974311111111-------
138101
6336261611876543321111111
846138221610
7543321111111111
364266167
9669433022191613119766543332
476347219126
91564029252017141110
98654433
24117611164462820151210
876544321111
6084432791611167151373226221815131110
875544
1 1/432
1/213
3/419
125
251
1 1/238
376
3 1/289
2 1/264
4102
Maximum Number of conductors in Type A,Rigid PVC Conduit - Cables TW and THW
44
1 1/432
1/213
141210
86421
1/02/03/04/0
250300350400500600750800900
1000
3/419
125
251
1 1/238
376
3 1/289
2 1/264
4102
SIZEAWG /kcmil
NOMINAL CONDUIT DIAMETER (Inches / mm)
1 1/432
1/213
141210
86421
1/02/03/04/0
250300350400500600750800900
1000
3/419
125
251
1 1/238
376
3 1/289
2 1/264
4102
SIZEAWG /kcmil
NOMINAL CONDUIT DIAMETER (Inches / mm)
Maximum Number of conductors in Type A,Rigid PVC Conduit - Cables THHN and THWN-2
7353331914
864432111111111--
161174311111------------
271912
7531111111---------
44322012
8532211111111-----
150109
6940281712
986543322111111
9670442518118654332111111111
338246155
896439282117141210
8765433322
441321202117845237272319161310
987654433
225164103
59432619141110
865443321111
566412260150108
66473529242017141210
9765544
51392916
975332111111111---
1186311111-------------
181410
632111111----------
31241810
643111111111------
105806033201511765443221111111
6751382113
97543321111111111
235181135
7545332417141210
97655433221
307236176
9859443222191613119876543333
157120
89503022161110
8764433211111
395303226125
75564129242117141210
98754443