Building Systems( Research)
-
Upload
ahmad-nadeem-ezzat -
Category
Documents
-
view
221 -
download
0
Transcript of Building Systems( Research)
-
8/2/2019 Building Systems( Research)
1/12
Building systems and their types:
Buildings are those structures which are located above the ground level and they
are built according to the intended use for people as a residential, office and
other purposes which are of many types and built according to the environmentalgeological and other aspect of its surroundings.
Building Types:
Compared to the medieval ages, architecture nowadays has really changed a lot. Technical
revolutions, the advances in technology and industrialization and the demands for certain types
of buildings have exploded. This leads to magnificent works of art which over the years have
become true monuments and engineering breakthroughs which are stunning even in today's
standards.
Thus buildings and structures by type are different nowadays and they can be seen everywhere
in our home town. Steel buildings are structures made of metal and they use steel both for
exterior and interior support. The reason for steel buildings coming to life is that they provide a
good space for office spaces that can be rented and thus generate important revenue. But they
are also good as a living space, nonetheless. These types of buildings do have very good
reinforced structures and they are also cost effective. When it comes to heating, steel is a good
material that conducts heat so the cost for cooling the spaces within the building will be high.
Another drawback when it comes to steel buildings is that corrosion can really take its toll on
them in time and thus the cost of maintenance is also on the upper level.
When we are talking about storage sheds then we are talking about a single story structure that
has many other uses than of a residential space. These structures are generally used for storing
large crafts like airplanes, locomotives, ships and large vehicles and they are very tall given their
use. I am absolutely sure that you have seen these structures before, when traveling by plane
especially.
Another type of building is the industrial type. They are very large and are mostly built on many
square kilometers of land. They are mainly used for manufacturing of different products as well
as storage.
Architecture though has also functional factors that have to take care of. Architecture focuses on
practical use rather than looks. So each type of building be it a church, a prison, a castle or
something else has unique functional requirements that are linked directly with the
-
8/2/2019 Building Systems( Research)
2/12
architecture's meaning. This doesn't mean that any building is constructed with extreme care on
these factors. There are buildings that stand out there just to compliment a need, which of
course is subjective and thus won't render a high quality and a precise building construction
process. And yet, structural and functional factors weren't always vital. In the past, the
architects tried and also succeeded to define their buildings through unique carvings and models
that weren't actually linked with a functional mechanism, but rather they would look good and
render them different from other buildings.
Every building type has different design and efficiency depending on their
functions like e.g.
y Agricultural buildings
y Commercial buildings
y Residential buildings
y Educational buildingsy Government buildings
y Industrial buildings
y Military buildings
y Parking and storage
y Religious buildings
y Transit stations
y Other
Building components:
Component of buildings are as follow:
1. Foundation
2. Floors (Storys)
3. walls
4. Columns
5. Beams
6. Slabs
7. Doors & windows8. Stairs, Ramps, Elevators.
9. Roof of the building.
-
8/2/2019 Building Systems( Research)
3/12
Structural Types
The structural types are divided into the following categories.
Bridges and Viaducts
Buildings
Towers and Masts
Tunnels and Underground Structures
FLOORSOF A BUILDING:
Floors of a building is the level of the building which people lives and
consist of rooms ,kitchens ,halls and etc, and in any tall building it consist of
many floors also called storys.
WALLS:
Walls are the most important parts of any building which provides
partitions, provides privacy, can resist winds and possesses insulation and
also acts as a load bearing part of a building.
The buildings which are going to be is to be made should have satisfied the
required condition of its construction.
At first we should opt the geological investigation, which is very useful to the
bearing capacity of the soil and so the other aspects of soil which the building is
going to be made.
-
8/2/2019 Building Systems( Research)
4/12
The investigation of soil requires many tests which normally we have the tests for
compaction, percolation, Ph-test, squeeze test, worm test.
These tests are very useful and are a must to be done for having efficient
foundation with good bearing capacity to have strength and stability againstmoisture, differential settlements, collapse and other bad effects.
Soil compaction is another work which is to be done before the building and the
foundation is constructed.
Foundation:
A foundation is the lowest and supporting layer of a structure. Foundations are generally
divided into two categories: shallow foundations and deep foundations
Shallow foundations
Shallow foundations, often called footings, are usually embedded about a meter or so into soil. Onecommon type is the spread footing which consists of strips or pads of concrete (or other materials) which
extend below the frost line and transfer the weight from walls and columns to the soil or bedrock.
Another common type of shallow foundation is the slab-on-grade foundation where the weight of the
building is transferred to the soil through a concrete slab placed at the surface. Slab-on-grade foundationscan be reinforced mat slabs, which range from 25 cm to several meters thick, depending on the size of the
building, or post-tensioned slabs, which are typically at least 20 cm for houses, and thicker for heavier
structures.
Deep foundations
A deep foundation is used to transfer a load from a structure through an upper weak layer of soil to
a stronger deeper layer of soil. There are different types of deep footings including impact driven
piles, drilled shafts, caissons, helical piles, and earth stabilized columns. The naming conventions
for different types of footings vary between different engineers. Historically, piles were wood, later
steel, reinforced concrete, and pre-tensioned concrete.
Soil Compaction
-
8/2/2019 Building Systems( Research)
5/12
Soil Compaction
Soil compaction is defined as the method of mechanically increasing the density of soil. Inconstruction, this is a significant part of the
building process. If performed improperly,
settlement of the soil could occur and result inunnecessary maintenance costs or structurefailure. Almost all types of building sites and
construction projects utilize mechanicalcompaction techniques.
Why Compact?There are five principle reasons to compact soil: - Increases load-bearing capacity
- Prevents soil settlement and frost damage- Provides stability- Reduces water seepage, swelling and contraction
- Reduces settling of soil
Types of CompactionThere are four types of compaction effort on soil or asphalt:
y Vibrationy Impact
y Kneading
y Pressure
These different types of effort are found in the two principle types of compaction force: static
and vibratory.
Static force is simply the deadweight of the machine, applying downward force on the soil
surface, compressing the soil particles. The only way to change the effective compaction force
is by adding or subtracting the weight of the machine. Static compaction is confined to uppersoil layers and is limited to any appreciable depth. Kneading and pressure are two examples of
static compaction.
Vibratory force uses a mechanism, usually engine-driven, to create a downward force inaddition to the machine's static weight. The vibrating mechanism is usually a rotatingeccentric weight or piston/spring combination (in rammers). The compactors deliver a rapid
sequence of blows (impacts) to the surface, thereby affecting the top layers as well as deeperlayers. Vibration moves through the material, setting particles in motion and moving them
closer together for the highest density possible. Based on the materials being compacted, acertain amount of force must be used to overcome the cohesive nature of particular particles.
-
8/2/2019 Building Systems( Research)
6/12
Results of Poor Compaction
Both illustrations above show the result of improper compaction and how proper compaction
can ensure a longer structural life.
SOIL TYPES & CONDITION
-
8/2/2019 Building Systems( Research)
7/12
Every soil type behaves differently with respect to maximum density and optimum moisture.
Therefore, each soil type has its own unique requirements andcontrols both in the field and for testing purposes. Soil types are
commonly classified by grain size, determined by passing thesoil through a series of sieves to screen or separate the different
grain sizes. Soil classification is categorized into 15 groups, asystem set up by AASHTO (American Association of State
Highway and Transportation Officials). Soils found in nature arealmost always a combination of soil types. A well-gradedsoil
consists of a wide range of particle sizes with the smallerparticles filling voids between larger particles. The result is a
dense structure that lends itself well to compaction. A soil'smakeup determines the best compaction method to use. They are
three basic soil groups:
y Cohesive
y
Granulary Organic (this soil is not suitable for compaction and will
not be discussed here)
Cohesive soilsCohesive soils have the smallest particles. Clay has a particle
size range of .00004" to .002". Silt ranges from .0002" to .003".Clay is used in embankment fills and retaining pond beds.
CharacteristicsCohesive soils are dense and tightly bound together by molecular
attraction. They are plastic when wet and can be molded, butbecome very hard when dry. Proper water content, evenly distributed, is critical for proper
compaction. Cohesive soils usually require a force such as impact or pressure. Silt has anoticeably lower cohesion than clay. However, silt is still heavily reliant on water content.
Granular soilsGranular soils range in particle size from .003" to .08" (sand) and .08" to 1.0" (fine to medium
gravel). Granular soils are known for their water-draining properties.
Characteristics
Sand and gravel obtain maximum density in either a fully dry or saturated state. Testingcurves are relatively flat so density can be obtained regardless of water content. The tables that
follow give a basic indication of soils used in particular construction applications.
Guide to Soil Types
What to look for Appearance/Feel Water Movement When Moist When Dry
-
8/2/2019 Building Systems( Research)
8/12
Granular soils,fine sands andsilts
Coarse grainscan be seen.Feels gritty whenrubbed betweenfingers
When water andsoil are shaken inpalm of hand,they mix. Whenshaking isstopped they
separate
Very little or noplasticity
Little or nocohesive strengthwhen dry. Soilsample willcrumble easily.
Cohesive soils,mixes and clays
Grains cannot beseen by nakedeye. Feelssmooth andgreasy whenrubbed betweenfingers
When water andsoil are shaken inpalm of hand,they will not mix
Plastic and sticky.Can be rolled
Has high strengthwhen dry.Crumbles withdifficulty. Slowsaturation inwater.
MaterialsVibrating SheepsfootRammer
Static SheepsfootGrid RollerScraper
Vibrating Plate CompactorVibrating RollerVibrating Sheepsfoot
ScraperRubber-tired RollerLoaderGrid Roller
Lift Thickness ImpactPressure
(with kneading)Vibration
Kneading(with pressure)
Gravel12+ Poor No Good Very Good
Sand 10+/- Poor No Excellent Good
Silt 6+/- Good Good Poor Excellent
Clay 6+/- Excellent Very Good No Good
Fill Materials
Permeability Foundation SupportPavement Sub grade ExpansiveCompaction
Difficulty
Gravel Very High Excellent Excellent No Very Easy
Sand Medium Good Good No Easy
Silt Medium Low Poor Poor Some Some
Clay None+ Moderate Poor Difficult Very Difficult
Organic Low Very Poor Not Acceptable Some Very Difficult
Effect of MoistureThe response of soil to moisture is very important, as the soil must carry the load year-round.
Rain, for example, may transform soil into a plastic state or even into a liquid. In this state,soil has very little or no load-bearing ability.
Moisture vs. Soil DensityMoisture content of the soil is vital to proper compaction. Moisture acts as a lubricant within
-
8/2/2019 Building Systems( Research)
9/12
soil, sliding the particles together. Too little moisture means inadequate compaction - the
particles cannot move past each other to achieve density. Too much moisture leaves water-filled voids and subsequently weakens the load-bearing ability. The highest density for most
soils is at a certain water content for a given compaction effort. The drier the soil, the moreresistant it is to compaction. In a water-saturated state the voids between particles are partially
filled with water, creating an apparent cohesion that binds them together. This cohesionincreases as the particle size decreases (as in clay-type soils). l
Soil Density Tests
To determine if proper soil compaction is achieved for any specific construction application,
several methods were developed. The most prominent by far is soil density.
Why Test?
Soil testing accomplishes the following:
y Measures density of soil for comparing the degree of compaction vs. specsy Measures the effect of moisture on soil density vs. specs
y Provides a moisture density curve identifying optimum moisture
Types of Tests
Tests to determine optimum moisture content are done in the laboratory. The most common isthe Proctor Test, or Modified Proctor Test. A particular soil needs to have an ideal (or
optimum) amount of moisture to achieve maximum density. This is important not only fordurability, but will save money because less compaction effort is needed to achieve the desired
results.
-
8/2/2019 Building Systems( Research)
10/12
The Hand TestA quick method of determining moisture is known as the "Hand Test". Pick up a handful of
soil. Squeeze it in your hand. Openyour hand. If the soil is powdery and will not retain the shape made by
your hand, it is too dry. If it shatters when dropped,it is too
dry. If the soil is moldable and breaks into only acouple of
pieces when dropped, it has the right amount ofmoisture for proper compaction. If the soil is plastic
in your hand, leaves traces of moisture on yourfingers and stays in one piece when dropped, it has
too much moisture for compaction.
Proctor Test (ASTM D1557-91)
The Proctor, or Modified Proctor Test, determines the maximum density of a soil needed for aspecific job site. The test first determines the maximum density achievable for the materials
and uses this figure as a reference. Secondly, it tests the effects of moisture on soil density.The soil reference value is expressed as a percentage of density. These values are determined
before any compaction takes place to develop the compaction specifications. Modified Proctorvalues are higher because they take into account higher densities needed foe certain typed of
construction projects. Test methods are similar for both tests.
Proctor TestA small soil sample is taken from the jobsite. Astandard weight is dropped several times on thesoil. The material weighed and then oven dried for12
hours in order to evaluate water content
Modified Proctor TestThis is similar to the Proctor Test except ahammer is used to compact material for greaterimpact, The test is normally preferred in testing
materials for higher shearing strength.
Field TestsIt is important to know and control the soil density during compaction. Following are common
field tests to determine on the spot if compaction densities are being reached.
-
8/2/2019 Building Systems( Research)
11/12
Field Density Testing Method
Sand Cone Balloon Dens meter Shelby Tube NuclearGauge
Advantages * Large sample* Accurate
* Large sample* Direct readingobtained* Open graded material
* Fast* Deep sample* Under pipe haunches
* Fast* Easy to redo* More tests (statisticalreliability)
Disadvantages
* Many steps* Large area required* Slow* Halt Equipment* Tempting to accept flukes
* Slow* Balloon breakage* Awkward
* Small Sample* No gravel* Sample not alwaysretained
* No sample* Radiation* Moisture suspect* Encourages amateurs
Errors* Void under plate* Sand bulking* Sand compacted* Soil pumping
* Surface not level* Soil pumping* Void under plate
* Overdrive* Rocks in path* Plastic soil
* Miscalibrated* Rocks in path* Surface prep required* Backscatter
Cost * Low * Moderate * Low * High
Sand Cone Test (ASTM D1556-90)
A small hole (6" x 6" deep) is dug in the compacted material to betested. The soil is removed and weighed, then dried and weighed
again to determine its moisture content. A soil's moisture is
figured as a percentage. The specific volume of the hole isdetermined by filling it with calibrated dry sand from a jar andcone device. The dry weight of the soil removed is divided by the
volume of sand needed to fill the hole. This gives us the densityof the compacted soil in lbs per cubic foot. This density is
compared to the maximum Proctor density obtained earlier, whichgives us the relative density of the soil that was just compacted.
Nuclear Density (ASTM D2292-91)Nuclear Density meters are a quick and fairly accurate way ofdetermining density and moisture content. The meter uses a
radioactive isotope source (Cesium 137) at the soil surface(backscatter) or from a probe placed into the soil (direct
transmission). The isotope source gives off photons (usually
Gamma rays) which radiate back to the mater's detectors on the bottom of the unit. Dense soil
absorbs more radiation than loose soil and the readings reflect overall density. Water content(ASTM D3017) can also be read, all within a few minutes. A relative Proctor density with the
compaction results from the test.
-
8/2/2019 Building Systems( Research)
12/12
Soil Modulus (soil stiffness)This field-test method is a very recent development that replaces soil density testing. Soil
stiffness is the ratio of force-to-displacement. Testing is done by a machine that sendsvibrations into the soil and then measures the deflection of the soil from the vibrations. This is
a very fast, safe method of testing soil stiffness. Soil stiffness is the desired engineeringproperty, not just dry density and water content. This method is currently being researched and
tested by the Federal Highway Administration.
Compaction Equipment
ApplicationsThe desired level of compaction is best achieved by matching the soil type with its propercompaction method. Other factors must be considered as well, such as compaction specs and
job site conditions.
y Cohesive soils - clay is cohesive, its particles stick
together.* Therefore, a machine with a high impact force is required toram the soil and force the air out, arranging the particles. A rammeris
the best choice or apad-foot vibratory rollerif higher production isneeded.
*The particles must be sheared to compact.
y Granular soils - since granular soils are not cohesive and the
particles require a shaking or vibratory action to move them; vibratoryplates (forward travel) are the best choice.