BTS Attributes
-
Upload
elatbarawi -
Category
Documents
-
view
213 -
download
0
Transcript of BTS Attributes
-
8/17/2019 BTS Attributes
1/4
BTS attributes
Contents
5.2.14.1.2 BTS attributes
5.2.14.1.2 BTS attributes
This describes the BSC attributes, including the site attributes, cell attributes, TRX attributes, and channel
attributes. The users can learn the parameters when querying the BTS attributes.
Site Attributes
Table 1 describes the site attributes.
Table 1 Site attributes
Attribute Name Description
Manufacturer ID Information about the manufacturer of the BTS to be queried.
OML attribute Port number, timeslot number, and sub-timeslot number of the OML.
Operation state Whether the current site is available.
Terminal equipment ID Terminal equipment ID according to the LAPD protocol. The attribute here
indicates the equipment ID of the current site, that is, the terminal equipmentidentifier (TEI) of the OML.
Clock attribute Work status of the BTS clock and information related to the clock parameters.
Extended alarm
configuration
Configuration of the extended alarms of the current site.
Software configuration Software configuration of the current site.
Power supply system
type
Power supply system type of the BTS cabinet.
SFP Mode Connection attributes of the SFP port.
TOP Switch Parameters Information about the port and slot of the TOP switching parameters on the
backplane.
Hardware configuration Hardware configuration of the current site.
Cell attributes
Table 2 describes the cell attributes.
Table 2 Cell attributes
Attribute Name Description
http://void%280%29/http://void%280%29/
-
8/17/2019 BTS Attributes
2/4
Management state Management state of the current cell. You can set the state by choosing BTS
Maintenance > Modify Administrative State on the LMT.
BCCH ARFCN Frequency of the main BCCH of the current cell.
BTS Identity Code Consisting of BSIC, NCC, BCC.
Cell air-interface
timer
Duration of timer T3105. This attribute is used in asynchronous cell handover. Unit: ms
CCCH load
indication period
Interval for sending the overload messages.
CCCH load
threshold
Ratio of times of successful random access to total collision times within the time.
Connection failure
criterion
Detailed criterion for determining the connection failure.
Interference
average parameter
Average time for obtaining the interference level. The default value is 20 multiframe.
Interference level
threshold
The interference can be divided into six ranks according to the interference signal level.
The level value for dividing each rank is called interference level threshold.
The BTS determines which rank the current interference level is in and reports this
information to the BSC on the basis of the radio resource indication.
Maximum timing
advance
Maximum timing advance of the most distant area of a cell. This attribute can identify
the actual coverage of a cell.
NY1 Maximum times of sending physical messages.
Operation state Whether the current site is available.
Overload period The BTS calculates the channel usage at a fixed interval to check whether the channel
is overloaded. The interval is determined by the overloading period. Unit: s
RACH busy
threshold
Determining the level threshold of random access. Unit: dBm
RACH load average
timeslots
Measuring the average loading timeslot number for random access channel.
Start frame No. The command can be run in the case of this frame number. If you want to run the
command immediately, set the frame number to 65535.
The value range of frame number is 0 to 42432, and 65535.
T200 Consisting of the following parameters:
SDCCH: timeout duration of T200 defined on the SDCCH over the Um interface
FACCH/Full rate: timeout duration of T200 on the FACCH or full-rate channel at the Um
port
FACCH/Half rate: timeout duration of T200 on the FACCH or half-rate channel at theUm port
SACCH with TCH SAPI0: timeout duration of T200 on the SACCH when the TCH at the
Um port supports the SAPI0 service
SACCH with SDCCH: timeout duration of T2000 on the SACCH with SDCCH
-
8/17/2019 BTS Attributes
3/4
SDCCH SAIP3: value of T200 when the SDCCH supports the SAPI3 service
SACCH with TCH SAPI3: timeout duration of T200 on the SACCH when the TCH at the
Um port supports the SAPI3 service
VSWR threshold VSWR threshold of the RF voltage, including the VSWR threshold when an antenna
incurs a fault and the VSWR threshold when an antenna is not correctly adjusted.
Available state Current state of the cell.
Frequency hopping
mode
Determining whether to use the FH mode, and what kind of FH mode is used
Extended type &
extended offset
Extended type and extended offset of the current cell.
Frame offset
parameter
The default value of this attribute is 0. This indicates the cell is not offset. If the value is
not 0, the handover mode need be changed from synchronous to asynchronous. If the
value is 255, the BTS does not send this attribute. For BTS3001C and BTS2X BTSs,
the value of this attribute is fixed to 255.
The BTS3X, BTS3002C and double-transceiver BTSs can predict the frame offset
according to the value of frame offset parameter.
Interference band
statistical
algorithm
When the frequency point scanning function is enabled, interference band statistic
algorithm I or interference band statistic algorithm II is used.
Uplink frequency
scan
Uplink frequency scanning result.
TRX attributes
Table 3 describes the TRX attributes.
Table 3 TRX attributes
Attribute Name Description
Management state Management state of the current TRX. You can set the state by choosing BTS
Maintenance > Modify Administrative State on the LMT.
ARFCN list List of channel numbers based on which the channel works. In the case of none FH,
each channel has one channel number. In FH, all the available channel numbers are
listed in the ARFCN list.
Power level The static power is divided into five levels. The value set here indicates the power level
of the current TRX.
Output power
threshold
Maximum RC Power Reduction
Maximum RC
power reduction
Maximum power reduction of each level.
Operation state Whether the TRX is available.
Available state Current state of the TRX.
http://void%280%29/
-
8/17/2019 BTS Attributes
4/4
power attenuation
level
. ,
between levels is 0.2 dB.
RSL attribute Port number, timeslot number and sub-timeslot number of the RSL link.
Terminal
equipment ID
Information about the terminal equipment.
Channel Attributes
Table 4 describes the channel attributes.
Table 4 Channel attributes
Attribute Name Description
Management
state
Management state of the current channel. You can modify the state by choosing
Modify Administrative State on the LMT.
ARFCN list List of channel numbers based on which the channel works.
In the case of none FH, each channel has one channel number. In FH, all the available
channel numbers are listed in the ARFCN list.
Operation state Whether the channel is available.
Channel
combination
Combination type of the current channel.
Hopping
sequence No.
Numbers of 64 kinds of FH. The number 0 indicates the FH in sequence. Other values
indicate the FH of pseudo-random sequence.
Mobile allocation
index offset
Frequency offset when the TRXs are in FH in the same cell.
Training sequence
code
Demodulation part for estimating the channel feature to correctly decode the valid
information. There are eight kinds of training sequence codes.
Available state Current state of the channel.
Parent topic: Concepts Related to BTS Maintenance
http://void%280%29/http://void%280%29/