HIGH PERFORMANCE PRE-APPLIED SYSTEM FOR BLIND SIDE & BELOW GRADE WATERPROOFING APPLICATIONS

BSW

is a fully reinforced Pre-Applied system membrane designed for horizontal and vertical external blind-side waterproofing applications. The system is composed of a select blend of high performance SBS modified bitumen combined with an ultra high strength reinforcement and a specially formulated top surface.

BSW

• Time & cost saving on project schedule & budget;• Eliminates the need for concrete screed on the horizontal;• Eliminates the need for protection board on the vertical;• Allows for optional design considerations for the use of water stop;• Excellent protection against water infiltration at critical locations;• Superior mechanical properties;• Resistant to chemicals (Chloride, Sulphate and Ph level between 2 and 10).• Outstanding adhesion to structural poured concrete;• Homogeneous, fully sealed systems on overlaps;• Non-Permeable to vapor and gas;• Fast & easy installation;• No tapes are required.

The system is to provide a full and continuous bond of the membrane to the poured structural concrete to waterproof and protect the sub-structure envelope from the blindside. This will eliminate the potential of water penetration and leakage.

COLPHENE BSW (Pre-Applied Waterproofing System Fully Bonded to Structural Concrete)

As it is normal behaviour of concrete to crack it is always necessary to protect it from water infiltration.

The technology and concept of COLPHENE BSW ensure watertight substructure envelope.

Waterproofing System(When not Bonded to the Structural Concrete Slab)

When water migration between membrane and structural concrete in blindside waterproofing is present, the structure becomes vulnerable and the liability of the design and construction team is huge and the remedy is expensive.

CONCEPT & VALUE CONCEPT

COLPHENE BSW system with its superior adhesion to poured concrete, high resistance to hydrostatic pressure and excellent resistance to tear and puncture is the optimum solution for the design and construction team to keep the water on the outside and ensure a dry, leak free substructure envelope.

VALUE

LOOSE LAID

FULLY BONDED TO THE BLINDING

1

FULLY BONDED TO STRUCTURAL CONCRETE

The COLPHENE BSW system membrane composition is designed with an engineered technology utilizing the exothermic synergy to create a superior mechanical bond-strength of the membrane to the structural poured concrete, introducing a unique, unsurpassed Pre-Applied / Blind-Side waterproofing system to the construction industry featuring:

The top face of the membrane is SBS modified bitumen covered with sand. The specially formulated surface softens slightly as the concrete starts to cure, releasing heat. This promotes adherence of the membrane to the concrete, and prevents the ingress or migration of water around the structure.

TECHNOLOGY

TECHNOLOGY

COLPHENE BSW can be used in application where high hydrostatic pressure is present. Membranes have been designed to withstand up to 114 m, where other conventional waterproofing become vulnerable.

COLPHENE BSW have been proven to resist water migration in such conditions.

RESISTANCE TO HYDROSTATIC HEAD

UV stabilized 60 days exposure to UV will not affect performance of waterproofing system.High mechanical properties to withstand traffic, puncture and exterior elements.

DURABILITY

60days

Penetrations through slabs and walls represent a high risk area for water penetration and leakage. At these points, it is crucial to ensure an effective continuous seal between the membrane and the penetration. ALSAN FLASHING single component, polyurethane, bitumen liquid is a UV resistant waterproofing membrane recommended for this application. This is an essential component of the system to ensure complete, continous seal of substructure envelope.

PENETRATION DETAILING

Waterproofing

• MORE WATERPROOFING CAPABILITIES

• ENHANCED REINFORCEMENT The ultra-high strength reinforcement is fully encapsulated in bitumen on both sides providing excellent dimensional stability.

• CONTINUOUS BOND Continuous and homogenous bond to structural concrete.

• LAP-ADHESION Unsurpassed lap adhesion.

• PEEL STRENGTH Excellent adhesion to the structural poured concrete surface.

• PUNCTURE RESISTANCE

Puncture resistant.

2

Slab on Grade

COLPHENE BSW PROTECT’R ( If Required)

COLPHENE BSW V

Prepared substrate

Earth

Concrete blinding

ALSAN FLASHINGPile Cap Head

Liquid Waterproofing Membrane

BSW

SYSTEM

ALSAN FLASHING (second layer)

ALSAN FLASHINGFLASHING reinforcement

ALSAN FLASHING (first layer)

ALSAN FLASHING

1. In vertical applications concrete can be cast directly onto the COLPHENE BSW V, no protection board is required.2. In horizontal applications, concrete can be cast directly onto the COLPHENE BSW H or over COLPHENE BSW PROTECT’R.

Notes: Selection and recommendation of a COLPHENE BSW PROTECT’R membrane depends on site conditions. For more information, please consult your local SOPREMA representative.

COLPHENE BSW H

3

COLPHENE PROTECT’R ( If Required)

COLPHENE BSW H

SYSTEMCOMPONENTS

MEMBRANES

Colphene BSW is applied directly to the prepared substrate or form workbefore structural concrete is poured.

COLPHENE BSW V (Vertical)

Top face is coated with specially treated silica sand.Underface is self-adhesive protected with a silicone release film.

Release plastic film

Select Blend

CompositeReinforcement

Special blendsand top face

Select Blend

COLPHENE BSW H (Horizontal)Top face is coated with specially treated silica sand.Underface is protected by polypropylene film.

Select Blend

PolyesterReinforcement

Special blendsand top face

Select Blend

Thermofusibleplastic film

COLPHENE BSW PROTECT’RTop face is coated with specially treated silica sand.Underface is self-adhesive protected with a silicone release film.

Select Blend

CompositeReinforcement

Special blendsand top face

Select Blend

Release plastic film

Polyurethane / bitumen liquid waterproofing membrane.

For sealing around penetrations

ALSAN FLASHING

Colour : BROWNPacking: Available in 3.78 L or 19 L pails.Pails per pallet: 24

4

TECHNICALPROPERTIES

TECHNICAL PROPERTIES

(All values are nominal)

Properties Standards COLPHENE BSW V COLPHENE BSW HCOLPHENE BSW H &COLPHENE BSW PROTECT’R

Tensile Strength, MD/XD ASTM D412 5.37 / 4.63 MPa 7.43 / 5.61 MPa

Ultimate Elongation, MD/XD ASTM D412 43 / 38 % 38 / 41 %

Tensile Strength, MD/XD ASTM D5147 14.2 / 11.9 MPa 27.9 / 21.1 MPa

Ultimate Elongation, MD/XD ASTM D5147 101 / 123 % 81 / 77 %

Low Temperature Flexibility ASTM D1970 Unaffected at -23°C Unaffected at -23°C

Adhesion of Poured Concrete ASTM D903 4248 N/m ---

Puncture Resistance ASTM E154 1210 N 1375 N

Resistance to Hydrostatic Head

ASTM D5385 114 m ---

Crack Cycling at -23°C ASTM C836 Unaffected ---

Tear Resistance, MD/XD ASTM D5147 611 / 474 N 1068 / 872 N

Tear Resistance, MD/XD ASTM D751 89 / 87 N 125 / 155 N

Lap Adhesion ASTM D1876 1.5 kN/m 23.5 kN/m ---

Perpendicular Adhesion ASTM D4541 --- 500 kPa ---

Peel Adhesion ASTM D903 2400 N/m --- ---

Water Vapour TransmissionASTM E96 method B

0.21 ng / Pa.s.m2 ---

Water Absorption ASTM D570 0.5% ---

SOPREMA Reserves the right to amend/modify the composition of its material and their prices without prior notice. Consequently all orders will be accepted only in accordance with the conditions and technical specifications in force at the date of the order.

Standards COLPHENE BSW V COLPHENE BSW H COLPHENE BSW PROTECT’R

Colour – Black Black Black

Thickness ASTM D3767 3.0 mm 3.5 mm 2.0 mm

Roll Dimensions – 1 x 10 m 1 x 10 m 1 m x 15 m

Roll Weight – 35 kg 43 kg 30 kg

Rolls per pallet – 30 25 30

Under face – Silicone Release Film Thermofusible Film Silicone Release Film

Top Face Sand

COMPOSITION & PACKAGING

PROPERTIES

5

APPLICATIONS,INSTALLATION

&ADVANTAGES

INSTALLATION GUIDELINES

APPLICATIONS• BLIND-SIDE (Where Excavation and Access are limited)

• BELOW-GRADE STRUCTURES

• UNDER CONCRETE SLABS AS VAPOUR BARRIER• RETAINING WALLS (POSITIVE SIDE)• TUNNELS & UNDERPASSES.

HORIZONTAL WATERPROOFINGa. In horizontal application apply the COLPHENE BSW H loose laid on the concrete blinding or compacted soil.b. End laps will be staggered by at least 300 mm.c. Seal all overlaps by heat-welding with a torch. Side lap to be minimum 75 mm and end lap to be minimum 150 mm.

VERTICAL WATERPROOFINGa. COLPHENE BSW V is installed in vertical strip of 5 meter maximum onto acceptable substrate by removing the siliconed release film on the underside.b. Ensure minimum 75 mm side overlap between each strip.c. Use a hard roller approved by membrane’s manufacturer to apply pressure over the entire surface of the membrane in order to ensure sufficient adhesion to prevent membrane movement during installation of poured in place concrete.d. Heat all side lap edges with a torch and use a round nose trowel to create a perfect seal with melted bitumen.e. The uppermost edge of each strip must be mechanically fastened to substrate using 50 mm (diameter) round plates and appropriate fasteners for blinding material at every 300 mm on centre.f. Horizontal joints shall be aligned and overlapped by minimum 200 mm covering all fasteners. g. Install a 300 mm reinforcement strip of COLPHENE BSW H fully heat-welded with a torch centered on all horizontal joints.

DETAILSa. All angle changes as well as inside and outside corners must be reinforced by installing an additional 300 mm piece of COLPHENE BSW H centered in the angle.b. All small protrusions (steel work, pile cap, etc.) through the waterproofing membrane, must be sealed with ALSAN FLASHING waterproofing coating and FLASHING REINFORCEMENT as required.

PROTECTION LAYERa. On all horizontal surfaces, it is recommended to apply COLPHENE BSW PROTECT’R as a protection layer over the COLPHENE BSW H prior to placement of the reinforcement steel bars as a precaution to limit the chances of any incidentals while work is in progress.b. Install the protection sheet in longitudinal strip centered over COLPHENE BSW H side laps by removing the siliconed realease film on the underside. c. Use a broom or a heavy roller to apply a uniform pressure over the entire surface of the protection sheet COLPHENE BSW PROTECT’R.

INSPECTION AND QUALITY CONTROLa. The contractor shall verify meticulously the membrane installation at the end of each day of work as well as before the steel work.b. Holes and tears in the membrane must be repaired with a reinforcement membrane (COLPHENE BSW H). The repair must exceed the affected surface area by at least 100 mm.

6

DETAILS

DETAILS

BLIND SIDE WATERPROOFING AT GRADE BEAMEXME-BSW01-1 (WOOD LAGGING)Scale: (N.T.S)

BLIND SIDE WATERPROOFING AT GRADE BEAMEXME-BSW01-2 (BLINDING)Scale: (N.T.S)

BLIND SIDE WATERPROOFING AT SLAB ON GRADEEXME-BSW02 Scale: (N.T.S)

BLIND SIDE WATERPROOFING AT SLAB ON GRADEEXME-BSW05 Scale: (N.T.S)

7

(If Required)(If Required)

(If Required)

(If Required)

DETAILS

DETAILS

BLIND SIDE WATERPROOFING AT JUNCTION (STEP 1)EXME-BSW06Scale: (N.T.S)

PILE CAP WATERPROOFING (SQUARE)EXME-BSW4-1Scale: (N.T.S)

BLIND SIDE WATERPROOFING AT GRADE BEAMEXME-SOP30Scale: (N.T.S)

BLIND SIDE WATERPROOFING AT JUNCTION (STEP 2)EXME-BSW06Scale: (N.T.S)

8

(If Required)

ColpheneProtect'R(If Required)

DETAILS

DETAILS

9

NEGATIVE WATERPROOFING

Hydrostaticpressure

Exterior space

Interior space

Blinding

Soil

Waterproofing treatment

Hydrostaticpressure

Concrete wall

Interior space

Waterproofing treatment

Exterior space

Soprema’s waterproofing membranes must always be used on positive side.

Blinding

Soil

POSITIVE WATERPROOFING

COLPHENE BSW PROTECT’R

COLPHENE BSW PROTECT’R must be centered on COLPHENE BSW H side laps.

COLPHENE BSW PROTECT’R

COLPHENE BSWH

Seal all overlaps by heat-welding with a torch. Side lap to be minimum 75 mm and end lap to be minimum 150 mm.

HORIZONTAL WATERPROOFING VERTICAL WATERPROOFING

Heat all side lap edges with a torch and use a round nose trowel to create a perfect seal with melted bitumen.

SOPR

EMA

EUROPE AFRICA ASIA MIDDLE EAST NORTH AMERICA SOUTH AMERICA OCEANIA

BSW