Brushless DC Motors - Dynetics · Nidec 10S, 17S and 28S Brushless DC Motors for DLP Technology...
Transcript of Brushless DC Motors - Dynetics · Nidec 10S, 17S and 28S Brushless DC Motors for DLP Technology...
Brushless DC Motorsfor Digital Light Processing™ Products
13
16.6
O26
O20
NAME PLATE/LOT NUMBER
O13.6
O6.5
1
2 MAX
O10 MAX
11.9
10.7 1.2
4DIMENSIONSIN MILLIMETERS
6 (3 PLACES)
8 (2 PLACES)
120° (3 Places)
O13.6
O12.8
M2 X 0.4(3 PLACES)
10S
17S
28S
10S 5.1 7,200 10,800 CW or CCW 9.5 6.0 12 11.4-12.6 200 50 Sleeve +5 +85 15,000
17S 6.0 7,200 10,800 CW or CCW 56.9 15 12 11.4-12.6 250 50 Sleeve +5 +85 20,000
28S 7.0 7,200 10,800 CW or CCW 234 20 12 11.4-12.6 350 53 Sleeve +5 +85 30,000
28S(4) 5.0 10,800 14,400 CW 56.0 10 12 11.4-12.6 120 50 Air Dynamic +5 +85 300,000(5)
Note: (1) Values are representative of current designs. Design-to-specification capabilities are available for these motors.(2) Maximum value.(3) Sound pressure is recorded at nominal speed under no-load conditions, 4.0 cm (axially) from the center of the top of the motor.(4) 28S motors with air dynamic bearings are available with a choice of balancing options: Material deposition or material removal.(5) ON/OFF cycles.™ Digital Light Processing is a brand trademark of Texas Instruments.
Torque Rotational Speed Max. Disk Load Operating Voltage No Load Sound Operating Temp. MotorConstant Nom. Max. Rotation Inertia Weight Nom. Range Current(2) Pressure(3) Min. Max. Life
Model (mNm/A) (rpm) (rpm) (Top View) (g-cm2) (g) (V) (V) (mA) (dBA) Bearing (°C) (°C) (hours)
Mechanical and Electrical Characteristics (1)
10S
28SAir Dynamic
Nidec America · phone 248-340-9977 · email [email protected] · www.nidec.com
Brushless DC Motorsfor Digital Light Processing™ Products
O10.8M2 X 0.4
(5 PLACES)
1517
179.5
O13.5
O18
O20.5
1 MAX
120° (3 PLAC
ES)
O8
O10 MAX
1.2
9.3
11.3
3.5 MAX
DIMENSIONSIN MILLIMETERS
813
NAME PLATE/LOT NUMBER
17S
25
NAME PLATE/LOT NUMBER
16
O33
O20+0.00-0.05
6.351.2
2 MAX
16.89 ±0.15
1.5 MAXSCREWINSERTION
O15 MAX
4.5 MAX
M3 (3 PLACES)
O23 14.45
18 ±0.5
5.5
1 ±0.3
FCI: SFW8R-2STE1
0.9 ±0.5 14.2
CO
IL C
CO
IL B
CO
IL A
CO
MM
ON
DIMENSIONSIN MILLIMETERS
13.8
120°
(3
PLAC
ES)
28S
Nidec America · phone 248-340-9977 · email [email protected] · www.nidec.com
Brushless DC Motorsfor Digital Light Processing™ Products
O33 ±0.1
O16+0.00- 0.05
O15.8
O13
O10.1
16
25
5
6.8 ±0.12
11.2
9.4 ±0.2 4.5 MAX
2.2 MAXSCREW INSERTION
1.2
BALANCEREMOVALWELLO2 MAX
NAME PLATE/LOT NUMBER
1.9 MAX
O18.5MAX
O15.2
M3(3 PLACES)
O23
R26R14.5
R14.45
18 ±0.5
11.5 ±0.5
1 ±0.3
DIMENSIONSIN MILLIMETERS
14.20.9 ±0.5
CONNECTORFCI: SFW8R-2STE1-LF
CO
IL C
CO
IL B
CO
IL A
CO
MM
ON
3.5MAX
13.8
120° (3
PLACES)
30°
28S Air DynamicFor MaterialRemovalBalancing
O33 ±0.1
O16+0.00- 0.05
O15.8
O13.6
O8
16
25
5
6.8 ±0.12
12.2
9.4 ±0.2 4.5 MAX
2.2 MAXSCREW INSERTION
1.2
BALANCEDEPOSITIONWELLNAME PLATE/
LOT NUMBER
1.9 MAX
O18.5MAX
O15.2
M3(3 PLACES)
O23
R26R14.5
R14.45
18 ±0.5
11.5 ±0.5
DIMENSIONSIN MILLIMETERS
CONNECTORFCI: SFW8R-2STE1-LF
CO
IL C
CO
IL B
CO
IL A
CO
MM
ON
2.2
120° (3
PLACES)
30°
14.20.9 ±0.5
13.8
1 ±0.3
28S Air DynamicFor MaterialDepositionBalancing
N/AHAJ
Nidec America · phone 248-340-9977 · email [email protected] · www.nidec.com
N/AHAJ