Bruel&Kjaer-2238 Logging Slm Software

download Bruel&Kjaer-2238 Logging Slm Software

of 74

Transcript of Bruel&Kjaer-2238 Logging Slm Software

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    1/74

    November 1998

    Brel & Kjr BB1125 112238 MediatorLogging SLM Software BZ7124

    User Manual

    2238 Mediator

    Integrating Sound Level Meter

    Logging SLM Software BZ 7124

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    2/74

    0 2 Brel & Kjr2238 MediatorLogging SLM Software BZ7124

    User Manual

    Trademarks

    2238 Mediator is a trademark of Brel & Kjr A/S.

    Copyright 1998, Brel& Kjr Sound & Vibration Measurement A/S

    All rights reserved. No part of this publication may be reproduced or

    distributed in any form, or by any means, without prior consent in writ-

    ing from Brel& Kjr Sound& Vibration Measurement A/S, Nrum,

    Denmark.

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    3/74

    BB1125 11 0 32238 MediatorLogging SLM Software BZ 7124

    User Manual

    4

    1

    Contents

    About this manual and the contents of the Logging module

    Pushkey definitions

    Explains how to set up parameters in the Measurement Set-up menu

    Gives instructions for changing the Measurement Window, for

    setting the markers and for setting a measurement to start

    automatically

    Gives information about data storage and about printing data

    Specifications for the Logging module

    List of default parameters and interface error messages

    Explains the programming of the interface jobs for the Logging

    module

    Introduction

    2Pushkey Definitions

    3

    The Measurement Set-up Menu

    Measuring

    5Data Handling

    6Specifications

    7Appendix 1: General

    8Appendix 2: Interface

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    4/74

    0 4 Brel & Kjr2238 MediatorLogging SLM Software BZ7124

    User Manual

    9Index

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    5/74

    BB1125 11 1 12238 MediatorLogging SLM Software BZ 7124

    User Manual

    Chapter 1

    Introduction

    1.1 About this Manual .............................................................. 1 2

    Summary of Contents........................................................ 1 2About this Volume............................................................. 1 3Measuring.......................................................................... 1 4Logging............................................................................... 1 4Detectors ............................................................................ 1 5Statistics ............................................................................ 1 6

    Aux 1................................................................................... 1 6Aux 2................................................................................... 1 6Measurement Set-up Menu .............................................. 1 6

    1.2 Measurement Parameters............................................... 1 7

    Parameters for Normal Logging Mode............................. 1 7Parameters for Short Logging Mode .............................. 1 10Parameters for Overall Measurement............................ 1 11

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    6/74

    Chapter 1 Introduction

    About this Manual

    1 2 Brel & Kjr2238 MediatorLogging SLM Software BZ7124

    User Manual

    1.1 About this Manual

    1.1.1 Summary of Contents

    Chapter 1 Introduction: provides a general overviewof the Logging module and its functions.

    Chapter 2 Pushkey Definitions: provides informa-tion about the pushkey functions for the Logging module.

    Chapter 3 Measurements Set-up Menu: gives in-structions for setting up the measurement parameters

    for the Logging module. Chapter 4 Measuring: gives instructions for making

    a logging measurement.

    Chapter 5 Data Handling: contains informationabout the parameters which are saved in the Loggingmodule, and how to print data.

    Chapter 6 Specifications: technical specifications forthe Logging module.

    Appendix 1 General: lists the default parameters andinterface error messages that are specific for the Loggingmodule.

    Appendix 2 Interface: gives instructions for using theinterface commands and queries for the Logging module

    Index

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    7/74

    Chapter 1 Introduction

    About this Manual

    BB1125 11 1 32238 MediatorLogging SLM Software BZ 7124

    User Manual

    1.1.2 About this Volume

    This volume of the User Manual deals only with the instruc-

    tions and functionality that are specific to the Logging module(Logging SLM Software BZ 7124).

    For information about the general operation and functionalityof Mediator please refer to the Basic User Manual (BZ7126)

    Conventions Used in this Manual

    Pushkeys

    References to buttons on the 2238 Mediator are shown withthe pushkeys pictogram as it appears on the instrument (forexample ). Refer to section 2.1 for a complete list of buttonpictograms and their functions.

    Soft Keys

    Mediator has two soft keys that have different functionsdepending on the current context. The soft keys functions aredenoted by chevrons () and courier type face. The current

    functions of the soft keys are always shown on the display.The soft key can have the following functions: ,, or . The soft key can have func-tions: , or. They can also havefunctions:or respectively, dependingon the selected parameter in the Measurement Window. Thisis similar to the functionality from the familiar Windows

    environment.

    Parameter Text

    Text which refers directly to text on the instruments screenor printouts is indicated using a Courier type face.

    For example: Press until Languageis highlighted in theSystem menu.

    Sockets

    Reference to sockets is made in bold type face (for example,

    Aux 1).

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    8/74

    Chapter 1 Introduction

    About this Manual

    1 4 Brel & Kjr2238 MediatorLogging SLM Software BZ7124

    User Manual

    1.1.3 Measuring

    When a measurement is started, a number of individual log-

    ging periods (depending on the set-up) are measured andsaved until the total measurement time has expired. At thesame time a number of Overall measurement parameters aremeasured for the total measurement time and are saved asa separate measurement result. This applies irrespective ofthe display setting during the measurement.

    1.1.4 Logging

    Logging Normal

    For typical applications with logging intervals of the order ofseconds or minutes Normal logging mode is used. It allowsup to 12 parameters (see section 1.2 below) to be selected forlogging.

    Logging Short

    Shortlogging is used for specialized measurements and hasa fixed 100 ms logging period. It allows logging of up to threeparameters:

    LXeq, Aux1 and Aux2

    Number of loggings

    Logging SLM Software BZ 7124 can store multiple files ofany size. The only limit for the number of loggings is theamount of memory that is available. Mediator has 2 Mbyteof memory. Data can also be logged via the serial interface,for example to a PC, in this case no file is created in Mediator.

    Time Remaining Check

    During measurement set-up Mediator displays the maximumpossible measurement time, based on the selected parame-ters, the logging rate and the available memory. The timevalue is automatically updated when you change parameters(see section 3.1.4).

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    9/74

    Chapter 1 Introduction

    About this Manual

    BB1125 11 1 52238 MediatorLogging SLM Software BZ 7124

    User Manual

    Logging Time

    The 2 Mbyte of memory in Mediator is shared among all the

    application modules installed. If a number of files has beencreated by, for example, the Basic module, the space occupiedby these files is not available for the Logging module.

    If more memory space is required for logging, you must loadthe application that occupies file space and the delete thefiles. If the file space is occupied by log files (extension M24),you can simply delete these files with the File Manager.Before deleting files, make sure that they are obsolete, savedto a PC or printed.

    Markers

    Markers are used to highlight various occurrences duringa measurement, for example, one type of marker can be usedto indicate areas that must be deleted during post-processing.Four markers are available.

    1.1.5 Detectors

    One of the main features of the Mediator is that it containstwo detectors with independent frequency weighting func-tions. In the Logging module, one is an RMS detector andthe other can be set up to measure RMS or Peak (only forNormallogging rate). This allows, for example, simultaneousmeasurement of A- and C-weighted RMS parameters.

    Linear and A- and C-weighting can be selected for both de-

    tectors. F (Fast), S (Slow) and I (Impulse) time weighting areavailable simultaneously in both RMS detectors.

    Short Logging Mode

    Mediator is set to a special mode of operation, when loggingperiod is set to Short. Detector 2 is selected and functions asan RMS detector with a 12ms time constant and values arelogged every 100 ms. For sound input the only parameter

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    10/74

    Chapter 1 Introduction

    About this Manual

    1 6 Brel & Kjr2238 MediatorLogging SLM Software BZ7124

    User Manual

    available is LXeq. This is because standard parameters suchas Lp, LMin, etc., are not defined with a 12 ms time constant.

    1.1.6 Statistics

    The Logging module can display up to seven LNvalues whichyou can set up from your own choice (LN is the percentilelevel expressing the level that has been exceeded for N% ofthe measurement time). The LN values are saved with themeasurement and they are measured for the individual log-ging periods.

    1.1.7 Aux 1

    In addition to the AC Output function in the basic version,Aux 1 can be set up as a DC input for an external signal.

    1.1.8 Aux 2

    In addition to the DC Output function in the basic version,

    Aux 2 can be set up as a DC input for an external signal, atrigger input or a trigger output.

    1.1.9 Measurement Set-up Menu

    The Measurement Set-up menu contains the following itemsin the Logging module:

    General (for setting the measurement range, the PeaksOver level and the 2nd exchange rate)

    Logging Periods (for setting up the period time (normal/short) and the logging interval)

    Logging Control (for setting up the destination for loggingdata (a file or via the serial interface) and for setting thetotal logging measurement time)

    Weightings (for setting the frequency weightings forDetector 1 and 2)

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    11/74

    Chapter 1 Introduction

    Measurement Parameters

    BB1125 11 1 72238 MediatorLogging SLM Software BZ 7124

    User Manual

    Parameters (for selecting and setting up the logging pa-rameters)

    Statistics (for setting up the LN

    values and time weight-ing)

    Correction Filters (for selecting correction filters forsound incidence and windscreen)

    Input/Output (for setting up the Aux 1 and Aux 2 sock-ets)

    Auto Start (for selecting an Auto Start)

    Save Setup (for saving a measurement set-up)

    Recall Setup (for recalling a measurement set-up)

    1.2 Measurement Parameters

    1.2.1 Parameters for Normal Logging Mode

    Table 1.3 lists the parameters available with the Loggingmodule, when Normal mode is selected. The X, V and Ysuffixes in the parameter names refer respectively to frequen-cy weightings (A, C or L), frequency weightings (C or L) andtime weightings (S, F or I).

    Note 1: It is not possible to select the same frequency weight-ing (A, C or L) for both detectors when they are both set toRMS.

    Note 2:Values for statistics are sampled 40 times a secondand are derived from the signal on Detector 1 with a pre-selected time weighting (F, S or I). The class width is 0.5 dB.Seven percentiles (LXYN,T) are available during measurementat user-selectable levels (1% to 99%).

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    12/74

    Chapter 1 Introduction

    Measurement Parameters

    1 8 Brel & Kjr2238 MediatorLogging SLM Software BZ7124

    User Manual

    Parameters Which Can Be Logged in Normal Logging Mode

    Parameter

    Default

    screenparameter

    Definition Freq.

    Weight-ing

    Time

    Weighting

    LXeq LAeq Equivalent continuouslevel for the duration ofthe measurement asdefined by IEC1672

    A, Cor L

    LXIeq LAIeq Equivalent continuouslevel of the impulse

    weighted SPL

    A, Cor L

    I

    LXYmax LAFmax Max. LXYpvalue detected

    within the elapsed time

    A, Cor L

    F, Sand I

    LXYmin LAFmin Min. LXYpvalue detected

    within the elapsed time

    A, Cor L

    F, Sand I

    LAFTm5 LAFTm5 Averaged Taktmaximal A F

    LAYav4 or

    LAYav5

    LAFav4

    or

    LAFav5

    Averaged sound levelwith an Exchange Rate of

    4 dB (LDOD) or5 dB (LOSHA)

    A F andS

    LXYN LAF1 ...LAF99

    Percentile levels A, Cor L

    F, S orI

    LVpkmax LCpkmax Max. Peak level detectedwithin the elapsed time

    C orLin.

    AUX1 AUX1 DC input from AUX 1

    AUX2 AUX2 DC input from AUX2

    Overload% Over-load%

    The percentage of timethat an overload occurred

    during a measurement

    Table 1.1 Parameters which can be logged (not instantaneous values) inNormal logging mode

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    13/74

    Chapter 1 Introduction

    Measurement Parameters

    BB1125 11 1 92238 MediatorLogging SLM Software BZ 7124

    User Manual

    Underrange% Under-range%

    The percentage of timethat an underrange

    occurred during a meas-

    urement

    Number ofPeaks

    #cPeaks Counts the number ofseconds where a speci-

    fied peak level isexceeded during a meas-

    urement

    C orLin.

    Instantaneous Parameters (Display Only)

    LXYInst LAFInst Instantaneous value of

    RMS level

    A, C

    or L

    F, S

    and I

    LXYp LAFp Sound pressure level(SPL)

    A, Cor L

    F, Sand I

    LVpk LCpk Instantaneous peak level C orLin.

    Elapsed Time ElapsedTime

    The amount of time thathas passed since the cur-rent logging period began

    (measurement timeexcluding pauses)

    Start Time StartTime

    The start time for the cur-rent logging period

    Start Date StartDate

    The start date for the cur-rent logging period

    Time Time The current time

    Log no. Log no. The current number oflogging periods over the

    measurement time

    Table 1.1 (cont.) Parameters which can be logged (not instantaneous val-ues) in Normal logging mode

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    14/74

    Chapter 1 Introduction

    Measurement Parameters

    110 Brel & Kjr2238 MediatorLogging SLM Software BZ7124

    User Manual

    1.2.2 Parameters for Short Logging Mode

    If the Short logging mode is selected, only the parameters

    listed in Table 1.2 can be logged and only a total maximumof three parameters.

    Parameters Which Can Be Logged in Short Logging Mode

    ParameterDefaultscreen

    parameter

    Definition Freq.Weight-

    ing

    TimeWeighting

    LXeq

    LAeq Equivalent continuouslevel for the duration ofthe measurement asdefined by IEC1672

    A, Cor L

    AUX1 AUX1 DC input from AUX 1

    AUX2 AUX2 DC input from AUX2

    Instantaneous Parameters (Display Only)

    Elapsed Time ElapsedTime

    The amount of time thathas passed since the cur-rent logging period began

    (measurement timeexcluding pauses)

    Start Time StartTime

    The start time for the cur-rent logging period

    Start Date StartDate

    The start date for the cur-rent logging period

    Time Time The current time

    Log no. Log no. The current number oflogging periods over the

    measurement time

    Table 1.2 Parameters which can be logged (not instantaneous values) inShort logging mode

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    15/74

    Chapter 1 Introduction

    Measurement Parameters

    BB1125 11 1112238 MediatorLogging SLM Software BZ 7124

    User Manual

    1.2.3 Parameters for Overall Measurement

    Table 1.3 lists the parameters available for an Overall meas-

    urement. The overall parameters are valid for all loggingperiods. The X, V and Y suffixes in the parameter namesrefer respectively to frequency weightings (A, C or L), fre-quency weightings (C or L) and time weightings (S, F or I).

    Note 1: It is not possible to select the same frequency weight-ing (A, C or L) for both detectors when they are both set toRMS.

    Overall Parameters For Normal Logging Mode

    ParameterDefaultscreen

    parameter

    Definition Freq.Weight-

    ing

    TimeWeighting

    LXeq LAeq Equivalent continuouslevel for the duration ofthe measurement asdefined by IEC1672

    A, Cor L

    LXIeq LAIeq Equivalent continuouslevel of the impulse

    weighted SPL

    A, Cor L

    I

    LXYmax LAFmax Max. LXYpvalue detected

    within the elapsed time

    A, Cor L

    F, Sand I

    LXYmin LAFmin Min. LXYpvalue detected

    within the elapsed time

    A, Cor L

    F, Sand I

    LVpkmax

    LCpkmax Max. Peak level detectedduring the measurement

    C orLin.

    Overload% Over-load%

    The percentage of timethat an overload occurred

    during a measurement

    Table 1.3 Parameters for an Overall measurement

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    16/74

    Chapter 1 Introduction

    Measurement Parameters

    112 Brel & Kjr2238 MediatorLogging SLM Software BZ7124

    User Manual

    Underrange% Under-range%

    The percentage of timethat an underrange

    occurred during a meas-

    urement

    Elapsed Time ElapsedTime

    The amount of time thathas passed since themeasurement began(measurement timeexcluding pauses)

    Start Time StartTime

    The start time for themeasurement

    Start Date StartDate

    The start date for themeasurement

    Number ofPeaks

    #cPeaks Counts the number ofseconds where a speci-

    fied peak level isexceeded during a meas-

    urement

    C orLin.

    Instantaneous Parameters (Display Only) for Normal Logging Mode

    LXYinst LAFInst Randomly sampledinstantaneous value ofRMS level

    A, Cor L F, S orI

    LXYp LAFp Sound pressure level(SPL)

    A, Cor L

    F, Sand I

    LVpk LCpk Instantaneous peak level C orLin.

    Time Time The current time

    Overall Parameters for Short Logging Mode

    LXeq LAeq Equivalent continuouslevel for the duration ofthe measurement asdefined by IEC1672

    A, Cor L

    Table 1.3 (cont.) Parameters for an Overall measurement

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    17/74

    Chapter 1 Introduction

    Measurement Parameters

    BB1125 11 1132238 MediatorLogging SLM Software BZ 7124

    User Manual

    Overload% Over-load%

    The percentage of timethat an overload occurred

    during a measurement

    Underrange% Under-range%

    The percentage of timethat an underrange

    occurred during a meas-urement

    Elapsed Time ElapsedTime

    The amount of time thathas passed since themeasurement began(measurement timeexcluding pauses)

    Start Time StartTime

    The start time for themeasurement

    Start Date StartDate

    The start date for themeasurement

    Instantaneous Parameters (Display Only) for Short Logging Mode

    Time Time The current time

    Table 1.3 (cont.) Parameters for an Overall measurement

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    18/74

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    19/74

    BB1125 11 2 12238 MediatorLogging SLM Software BZ 7124

    User Manual

    Chapter 2

    Pushkey Definitions

    2.1 Pushkey Definitions ........................................................... 2 2

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    20/74

    Chapter 2 Pushkey Definitions

    Pushkey Definitions

    2 2 Brel & Kjr2238 MediatorLogging SLM Software BZ7124

    User Manual

    2.1 Pushkey Definitions

    Each pushkey on the Mediators front panel is marked witha pictogram. This section gives a brief explanation of thebuttons.

    Power Press this key to switch the instru-ment on or off. The instrument willbe in pause mode when started up.

    Calibrate Press this key to calibrate your in-strument.

    System Press this key to display the Sys-tem menu for configuring the in-strument and for changingapplication programs.

    Data Files Press this key to select the DataFiles menu. The menu options inthis window allows you to save, de-lete and print and to access the File

    Manager facility.

    Set-up Press this key to access/stepthrough the set-up options in theMeasurement Set-up menu.

    Up/Down Arrows Press these keys to step up/downin the menu items in the selectedwindow. Also for entering/exiting

    edit mode in the MeasurementWindow.

    Left/Right Arrows Press these keys to select the pa-rameters in the selected window.

    Note: For the sake of consistencythe keys are always usedto select menu items, and the

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    21/74

    Chapter 2 Pushkey Definitions

    Pushkey Definitions

    BB1125 11 2 32238 MediatorLogging SLM Software BZ 7124

    User Manual

    keys are always used to se-lect values.

    Range Press this key to access the RangeSetting menu. Use thekeys to step through the availablemeasurement ranges or scroll withthe key.

    Reset Press this key to reset the meas-urement (only when the measure-ment is stopped).

    Meas. Results Press this key in any of the set-upmenus to return to the Measure-ment Window. If menu changeshave not been saved, they will becancelled.

    Start/Stop Press this key to start or stop ameasurement. A logging cannot bepaused and restarted. If you stop a

    measurement the current loggingperiod is saved as a partial loggingwith the time that passed until themeasurement was stopped. Fourmarkers are available for indicat-ing various occurrences.

    Select Softkey with functions ,, or de-pending on the cursor position in

    the current menu. The function displays the File ManagerOptions Window.

    Cancel Softkey with functions ,or depending onthe cursor position in the currentmenu.

    0

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    22/74

    Chapter 2 Pushkey Definitions

    Pushkey Definitions

    2 4 Brel & Kjr2238 MediatorLogging SLM Software BZ7124

    User Manual

    Backlight Switches the displays backlight onor off. To save batteries, the back-light switches off automatically af-

    ter 30 seconds.

    In addition to the functionality of the Basic module, the fol-lowing pushkeys have added functions in the Logging module:

    Freq. W. The function selectsthe frequency weighting parameterin the Measurement Window.

    Time W. The function selects

    the time weighting parameter inthe Measurement Window.

    Meas. Window Switches between the OverallMeasurement Window and the Log-ging Window.

    During Measurement

    Marker 1 For setting markers type 1

    Marker 2 For setting markers type 2

    Marker 3 For setting markers type 3

    Marker 4 For setting markers type 4

    Refer to section section 4.1.1 for more information aboutmarkers.

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    23/74

    BB1125 11 3 12238 MediatorLogging SLM Software BZ 7124

    User Manual

    Chapter 3

    Measurement Set-up Menu

    3.1 Measurement Set-up Menu ............................................ 3 2

    Introduction....................................................................... 3 2Measurement Set-up Menu .............................................. 3 2Setting the Logging Periods.............................................. 3 2Setting the Logging Control.............................................. 3 3Setting Frequency Weightings (Normal)....................... 3 5Setting Frequency Weightings (Short) .......................... 3 7Parameters......................................................................... 3 8Setting the Statistics Parameters .................................... 3 9Setting up the Input/Output Function........................... 3 10

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    24/74

    Chapter 3 Measurement Set-up Menu

    Measurement Set-up Menu

    3 2 Brel & Kjr2238 MediatorLogging SLM Software BZ7124

    User Manual

    3.1 Measurement Set-up Menu

    3.1.1 Introduction

    This chapter explains how to set up measurement parametersthat are specific for the Logging module. Refer to the BasicUser Manual for other parameters.

    3.1.2 Measurement Set-up Menu

    Logging SLM Software BZ 7124 contains the menu itemsshown in Fig. 3.1.

    3.1.3 Setting the Logging Periods

    The Log. Periods Window is used for setting the length(duration) of a single logging result. In Shortmode the log-ging period is fixed to 100ms. The Log. Periods Windowis shown in Fig.3.2.

    Setting the Period Time

    Normal

    Short

    Fig.3.1 The Measurement Set-up menu (three windows)

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    25/74

    Chapter 3 Measurement Set-up Menu

    Measurement Set-up Menu

    BB1125 11 3 32238 MediatorLogging SLM Software BZ 7124

    User Manual

    The Normal setting is used for most measurements and al-lows you to set the logging duration from 1 second to 60minutes.

    Short is only used for special measurements that requirevery short logging periods. Shorthas a fixed logging durationof 100 ms and allows a maximum of three logging parametersto be stored.

    Setting the Duration of Each Period

    The Logged Every field can only be accessed when the Pe-riod Time is set to normal.

    Minutes: Can be set from 00 to 60 in one minute steps

    Seconds: Can be set from 00 to 60 in one second steps

    3.1.4 Setting the Logging Control

    The Log. Control Window is used for setting the locationfor storing the logging files and for setting the total meas-urement time for a logging, see Fig. 3.3.

    Fig.3.2 The Logging Periods Window in Normal and Short logging modes

    Fig.3.3 The Logging Control Window

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    26/74

    Chapter 3 Measurement Set-up Menu

    Measurement Set-up Menu

    3 4 Brel & Kjr2238 MediatorLogging SLM Software BZ7124

    User Manual

    Setting the Destination

    File

    Interface

    Select Fileto store the logging result in Mediators internalmemory. You can store up to 2 Mbyte of data. Files of anysize can be handled as long as they are within the 2Mbytelimit.

    Use the Interface setting if you want to transfer thelogging results directly to a PC or laptop. The PC and Medi-ator must be set up as described in Chapter 7 in the Basic

    Manual.

    Note:D

    ata transfer will stop if an interface command is sent duringdata transmission

    Setting the Measurement Time

    Continuous

    Pre-set

    Continuous is normally used with the Interface settingabove, if you want to transfer logging data continuously to aPC. However, it is possible to use the Continuousmode withthe Filesetting. In this case logging continues until manu-ally stopped or Mediators internal memory is full.

    When you select Pre-seta Timefield will appear below thatallows you set up a maximum desired logging time.

    In the Timefield you can set up any total logging time from1 second to 7440 hours (310 days and nights) in 1 second steps:

    0000: The first two decimals are used for setting hoursin thousands and hundreds, the next set of decimals setthe tens of hours and the hours.

    00:01: For setting minutes (first two decimals) and sec-onds. Minimum measurement time is 1 second.

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    27/74

    Chapter 3 Measurement Set-up Menu

    Measurement Set-up Menu

    BB1125 11 3 52238 MediatorLogging SLM Software BZ 7124

    User Manual

    Example:411 hours, 15 minutes and 5 seconds appear as:

    0411:15:05

    Note:The Timefield can only be accessed when Meas. Timeis set to Pre-set.

    The Avail. Time field provides an approximate (conserva-tive) estimate of the logging time capacity, based on the cur-rent set-up and the currently available memory space.

    Table 3.1 below shows typical examples of total logging timesfor different number of standard parameters in dB. The log-ging period is 1 s. It is assumed that the full 2Mbyte of

    memory is available.

    For longer logging periods you can multiply the times in thetable with the number of seconds for the desired loggingperiod, for example, you can log three parameters with a1 minute period for approx. half a year.

    3.1.5 Setting Frequency Weightings (Normal)

    The Weightings Window is used for setting up frequencyweightings for detectors 1 and 2, see Fig. 3.4.

    It is not required to set the time weighting (F, S, I) in theLogging module since they are always measured simultane-ously.

    No. of Parameters Time (hours) Time (days)

    1 >173 7

    3 >76 3

    6 >41 1.7

    10 >25 1

    Table 3.1 Typical examples of logging times with logging every second

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    28/74

    Chapter 3 Measurement Set-up Menu

    Measurement Set-up Menu

    3 6 Brel & Kjr2238 MediatorLogging SLM Software BZ7124

    User Manual

    Setting Bandwidth for Detector1 (RMS)

    Broad Band

    1/3-octave

    1/1-octave

    Select the desired option in the Bandwidth field.

    Note: The 1/3-octave and 1/1-octave options only ap-pear when the 1/1-octave and 1/3-octave Filter Set is installedin Mediator.

    Setting Frequency Weighting for Detector1

    A, C, L (Broadband)

    31.5Hz ... 8kHz (1/1-octave)

    20Hz ... 12.5kHz (1/3-octave)

    Select the desired standardised frequency weighting or centrefrequency in the Freq. Wgt. field. The centre frequenciesdepend on the setting in the Bandwidth field.

    Setting Frequency Weighting for Detector 2 (Broadband) Peak/C

    Peak/L

    RMS/A

    RMS/C

    RMS/L

    Fig.3.4 The Weightings Window

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    29/74

    Chapter 3 Measurement Set-up Menu

    Measurement Set-up Menu

    BB1125 11 3 72238 MediatorLogging SLM Software BZ 7124

    User Manual

    In the Weighting field you can set Detector 2 to Peak withC or L frequency weighting or to RMS with A, C or L fre-quency weighting.

    3.1.6 Setting Frequency Weightings (Short)

    The LXeqparameter is based on the output from Detector2.Switching to the Short logging mode results in a change ofthe logging parameters and Detector 2 is set to RMS.

    Setting Bandwidth for Detector 2 (RMS)

    Broad Band 1/3-octave

    1/1-octave

    Select the desired option in the Bandwidth field.

    Note: The 1/3-octave and 1/1-octave options only ap-pear when the 1/1-octave and 1/3-octave Filter Set is installedin Mediator.

    Setting Frequency Weighting for Detector1

    A, C, L (Broadband)

    31.5Hz ... 8kHz (1/1-octave)

    20Hz ... 12.5kHz (1/3-octave)

    Select the desired standardised frequency weighting or centrefrequency in the Freq. Wgt. field. The centre frequenciesdepend on the setting in the Bandwidth field.

    Fig.3.5 The Weighting Window in Short logging mode

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    30/74

    Chapter 3 Measurement Set-up Menu

    Measurement Set-up Menu

    3 8 Brel & Kjr2238 MediatorLogging SLM Software BZ7124

    User Manual

    3.1.7 Parameters

    The Parameters Window is used for selecting the parame-

    ters that are saved with a logging result and to set up thedesired weighting for these parameters.

    Note: Overall measurement parameters, see Table 1.3, arealways measured.

    Normal/Short:

    When Normallogging mode is selected the Parameterswin-dow will appear as shown in Fig. 3.6. In this mode you can

    scroll through 12 measurement parameters in three windows.Short logging mode is similar, but only contains three pa-rameter fields in a single window.

    Selecting Parameters

    Use the cursor keys to highlight the desired param-eter field and press the right cursor key or the Selectsoft key to get the Parameter Set-upWindow, see Fig.3.7.

    Fig.3.6 The Parameters Window

    Fig.3.7 The Parameter Set-up Window

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    31/74

    Chapter 3 Measurement Set-up Menu

    Measurement Set-up Menu

    BB1125 11 3 92238 MediatorLogging SLM Software BZ 7124

    User Manual

    Parameter Set-up

    Parameter: For selecting the desired measurement pa-rameter. You can scroll between:

    LXeq, LXIeq, LXYmax, LXYmin, LAFTm5, LAFav4, LAFav5,LASav4, LASav5, AUX1, AUX2, Overload, Underrange,LVpkmax, #VPeaks, LN1 ...LN7

    Freq. Wgt.: For selecting Detector 1 or Detector 2. Onlythe relevant selections are shown

    Time Wgt.: For selecting the time weighting (F, S, I) forthe selected parameter. You can only access this field iftime weighting is possible with the selected parameter.

    The info field at the bottom shows the selected parameterwith the current detector set-up.

    Note: N.A. is displayed if the selected combination of weight-ings is not possible with the selected detector. The parametercan still be selected for logging, but you must change thedetector setting (Detector 2: Peak/RMS), to allow measure-ment of the parameter.

    3.1.8 Setting the Statistics Parameters

    The LNpercentiles express the level that has been exceededfor N% of the measurement time. The LN values are savedwith the measurement and they are measured for the indi-vidual logging periods. The percentiles can be set between 1and 99.

    The percentile levels are always based on the output fromdetector 1 and the associated frequency weighting.

    The StatisticsWindow allows you to define seven percen-tile levels which can be displayed simultaneously in the Meas-urement Window, see Fig.3.8.

    Setting the Time Weighting for Statistics

    F, S, I

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    32/74

    Chapter 3 Measurement Set-up Menu

    Measurement Set-up Menu

    310 Brel & Kjr2238 MediatorLogging SLM Software BZ7124

    User Manual

    The Time Weightingfield is used to select the time weight-ing used for the statistics. You can select the standardised F,Sand I time weightings.

    Setting the Percentile Levels

    L1 L99

    For each of the seven LN parameters, you can set N to avalue between 1 and 99 in steps of 1.

    3.1.9 Setting up the Input/Output Function

    The Input/Output Window controls the function of theAux 1and Aux 2inputs/outputs. See Fig. 3.9.

    Setting Up Aux1

    In the Aux1 field you can select:

    AC Output

    DC Input

    Fig.3.8 The Statistics Window

    Fig.3.9 The Input/Output Window

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    33/74

    Chapter 3 Measurement Set-up Menu

    Measurement Set-up Menu

    BB1125 11 3112238 MediatorLogging SLM Software BZ 7124

    User Manual

    AC Outputis used for switching the AC output signal to theAux 1 socket. Frequency weighting depends on theFreq. Wgt. field (see below). Full-scale indication corre-

    sponds to 1V RMS and the output is attenuated according tothe selected range. This output signal can be used, for exam-ple, for recording the measured signal on a DAT recorder.

    DC Input is used to set up the Aux 1 input to a DC Input.The external DC input must be in the range 0 to 4 V and theresolution is 5 mV. The DC input signal is displayed in theAUX1 parameter field and is saved with the measurementdata file, similar to the other measured parameters. Thisinput can be used, for example, for registering the wind speed

    together with the measurement result.

    Selecting Frequency Weighting

    The Freq. Wgt. parameter field only appears whenAC Output is selected for the Aux 1 socket:

    Linear

    Det. 1

    L frequency weighting is used when Linearis selected. Whenyou select Det. 1, the frequency weighting selected on theRMS detector is used.

    In Short logging mode the frequency weighting is alwaysLinear.

    Setting Up Aux2

    In the Aux2 field you can select:

    DC Output

    DC Input

    Trigger Input

    Trigger Output

    DC Outputsupplies a DC output signal equivalent to the ACoutput signal. It is the time weighted signal (Fast, Inst.) from

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    34/74

    Chapter 3 Measurement Set-up Menu

    Measurement Set-up Menu

    312 Brel & Kjr2238 MediatorLogging SLM Software BZ7124

    User Manual

    detector 1. Full-scale indication corresponds to 4.0V DC(50mV/dB).

    The function of DC Input is similar to that of Aux 1. It isused to set up the Aux 2 input to a DC Input. The externalDC input must be in the range 0 to 4 V and the resolutionis 5 mV. The DC input signal is displayed in the AUX2 pa-rameter field and is stored in a similar way to the othermeasured parameters.

    External Triggerstarts a measurement when an externaltrigger voltage is applied. The trigger level is 2 V (refer toSpecifications). A trigger is ignored if Mediator is not paused

    and is displaying the Measurement Window.

    Trigger Output supplies a status voltage that is high(>4 V DC) when a measurement is proceeding or low (0 V)when the instrument is paused. The Trigger Out signal canbe used to start/stop external equipment such as tape andlevel recorders.

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    35/74

    BB1125 11 4 12238 MediatorLogging SLM Software BZ 7124

    User Manual

    Chapter 4

    Measuring

    4.1 Selecting Measurement Window.................................. 4 2

    Markers.............................................................................. 4 3

    4.2 Setting a Measurement to Start Automatically.... 4 4

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    36/74

    Chapter 4 Measuring

    Selecting Measurement Window

    4 2 Brel & Kjr2238 MediatorLogging SLM Software BZ7124

    User Manual

    4.1 Selecting Measurement Window

    Two Measurement Windows are used with the logging mod-ule. When one of the Measurement Windows is displayed,and Mediator is stopped or measuring, you can switch be-tween the Overall Measurement Window and the LoggingMeasurement Window by using the key.

    Overall Measurement Window

    The Overall Measurement Window (Fig.4.1 ) shows the pa-rameter values for the total measurement time (as specifiedin the Timefield in the Logging ControlWindow). Exceptfor the Marker status box and the fact that only three pa-rameter fields are displayed, this window is similar to theMeasurement Window in the Basic and Enhanced modules.All measurement parameters available with the Logging mod-ule (see section 1.2) can be measured and displayed in theOverall mode.

    Note: Markers can be used when the Overall MeasurementWindow is displayed, however, the markers are saved with

    the current logging period and not with the overall measure-ment result.

    Logging Measurement Window

    The Logging Measurement Window (Fig.4.2 ) is similar tothe Overall Measurement Window. Note that the four param-eter values that are displayed only apply to the current log-ging period.

    Fig.4.1 Overall Measurement Window

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    37/74

    Chapter 4 Measuring

    Selecting Measurement Window

    BB1125 11 4 32238 MediatorLogging SLM Software BZ 7124

    User Manual

    Parameters that can be displayed in the Logging Measure-ment Window are:

    Instantaneous values (LXYinst, LXYp, Elapsed Time,

    Start Time, Start Date and Log no.)

    Parameters selected for logging (in the ParametersWindow, including Overload and Underrange).

    4.1.1 Markers

    Markers are used to highlight various occurrences during ameasurement. Four markers are available and they are re-ferred to as 1, 2 3 and 4. The keys in Fig.4.3 are usedfor activating the markers. These four keys are used for set-ting markers during a measurement only, otherwise they havetheir normal function. They have a toggle function, so that

    Fig.4.2 The Logging Measurement Window

    Fig.4.3 Keys used for markers (only during measurement). When amarker key is activated the corresponding square in the smallmarker status turns black to indicate which marker key hasbeen activated

    980391e

    1

    3

    2

    4

    1

    3

    2

    4

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    38/74

    Chapter 4 Measuring

    Setting a Measurement to Start Automatically

    4 4 Brel & Kjr2238 MediatorLogging SLM Software BZ7124

    User Manual

    the marker function remains active until the key is pressedagain. All four markers can be activated simultaneously. Themarker status box in the display indicates which marker is

    active.

    The marker settings are saved with each logging period.

    4.2 Setting a Measurement to StartAutomatically

    Mediator can manage up to four auto starts. Auto Starts areshared among the application modules that support them.Each Auto Start has a number (1 through 4) and is set tostart a specific application at a specified time (up to onemonth ahead) using a specified set-up. See also section 3.1.5in the Basic User Manual.

    From a specific software module, in this case Logging SLMSoftware BZ7124, all four Auto Starts can be seen and se-lected, but you can only set up an Auto Start for the currently

    running application module. If you want other applicationmodules to start, the Auto Start must be set from that mod-ule.

    To set up an Auto Start:

    1. Select Auto Startfrom the Measurement Set-up menu.

    If no Auto Start is set up, for example for Auto Start no.1, the display appears as:

    Fig.4.4 The basic Auto Start Window

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    39/74

    Chapter 4 Measuring

    Setting a Measurement to Start Automatically

    BB1125 11 4 52238 MediatorLogging SLM Software BZ 7124

    User Manual

    2. Use the cursor keysto select one of the four AutoStarts.

    If the Auto Start is active, the display will show theassociated application module as well as the set-upnumber and the start time.

    Use the cursor keys to select the Applicationfield, and use the cursor keys to select None orBZ7124. Nonemeans that the Auto Start is not active (ifpreviously set, the set-up parameters will be deleted ifyou press Ok). If the Auto Start is already activated byanother application module (for example BZ7125), the

    number of this application module is also among thechoices. The display will appear similar to Fig. 4.5.

    3. Set up the Date, Time and Use Setup no. fields asrequired. The date and time can be set to one monthahead.

    4. Press Ok to save the Auto Start.

    When switching Mediator off, the first occurring Auto Start

    is activated and the message in Fig. 4.6 is displayed.

    Note: An Auto Start only takes effect if Mediator is switchedoff at the time the Auto Start is supposed to run. If Mediatoris already switched on, the Auto Start is cancelled.

    If the Auto Start uses a set-up that specifies a pre-set meas-urement time, the instrument switches off when the meas-urement is completed, otherwise it will simply keep

    measuring until manually stopped.

    Fig.4.5 Auto Start set-up

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    40/74

    Chapter 4 Measuring

    Setting a Measurement to Start Automatically

    4 6 Brel & Kjr2238 MediatorLogging SLM Software BZ7124

    User Manual

    Mediator switches on approximately 30 s before the set timefor an Auto Start. This allows Mediator to settle and startmeasuring at exactly the set time.

    Fig.4.6 Confirmation of an Auto Start when switching Mediator off

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    41/74

    BB1125 11 5 12238 MediatorLogging SLM Software BZ 7124

    User Manual

    Chapter 5

    Data Handling

    5.1 Data Storage .......................................................................... 5 2

    Saved Data......................................................................... 5 2Set-up Data........................................................................ 5 2Overall Measurement Data Normal Mode.................... 5 2Overall Measurement Data Short Mode....................... 5 3Logging data Normal Mode ........................................... 5 3Logging Data Short Mode .............................................. 5 4

    5.2 Printing Data ........................................................................ 5 4

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    42/74

    Chapter 5 Data Handling

    Data Storage

    5 2 Brel & Kjr2238 MediatorLogging SLM Software BZ7124

    User Manual

    5.1 Data Storage

    5.1.1 Saved Data

    A measurement data file contains both overall measurementdata and a number of loggings. It consists of a group of set-up data, a group of associated measurement data and statis-tics data. The set-up data are:

    Serial number for Mediator unit

    Measurement set-up

    Calibration data

    Measurement data

    Measurement data are:

    Overall results

    Logging data (Normal or Short)

    5.1.2 Set-up DataMeasurement Set-up

    All measurement set-up parameters that were used for themeasurement.

    Calibration Set-up

    Microphone type

    Sensitivity

    Calibration date

    5.1.3 Overall Measurement Data Normal Mode

    Overall Results

    Overload

    Underrange

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    43/74

    Chapter 5 Data Handling

    Data Storage

    BB1125 11 5 32238 MediatorLogging SLM Software BZ 7124

    User Manual

    Elapsed Time

    Start Time

    Start Date Log no.

    Broadband Data for Detector 1 and 2

    LXeq, LXIeq, LXMax, LXMin

    Peak Data for Detector 2

    No. of peaks

    LVpkMax

    5.1.4 Overall Measurement Data Short Mode

    Overall Results

    Overload

    Underrange

    Elapsed Time Start Time

    Start Date

    Log no.

    Broadband Data

    LXeq

    5.1.5 Logging data Normal Mode

    General Results

    Overload

    Under-range

    Markers

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    44/74

    Chapter 5 Data Handling

    Printing Data

    5 4 Brel & Kjr2238 MediatorLogging SLM Software BZ7124

    User Manual

    Broadband Data for Detector1 and 2

    (Only those selected in the Parameters Window)

    LXeq, LXIeq, LXMax, LXMin, LAFTm5, LavF, LavS, LXYN, AUX1,AUX2

    Peak Data for Detector 2

    Number of peaks

    LVpkMax

    5.1.6 Logging Data Short Mode

    General Results

    Markers

    Broadband Data for Detector 2

    (Only those selected in the Parameters Window)

    LXeq, AUX1, AUX2

    5.2 Printing Data

    Printing is similar to the Basic module, the main differenceis that the Print Options menu does not exist, i.e. alllogged/saved measurement parameters are printed.

    You can print the current measurement or you can print a

    recalled file via the File Manager or by using the softkey.

    Note: You cannot print when logging data is being trans-ferred via the interface.

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    45/74

    BB1125 11 6 12238 MediatorLogging SLM Software BZ 7124

    User Manual

    Chapter 6

    Specifications

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    46/74

    Chapter 6 Specifications

    6 2 Brel & Kjr2238 MediatorLogging SLM Software BZ7124

    User Manual

    6.1 Specifications for LoggingSLM Software (BZ7124)

    Note: These Specifications are additional to

    the Specifications described in the Basic UserManualNote: All references to 1/3-octave bands or 1/1-octave bands apply only to instrument versionswith filter set installed.

    Measurements:The available measurement parameters are listedin the table. Detector 1 always measures RMSwhile Detector 2 measures RMS or Peak in par-allel (for Normallogging mode). The RMS detec-tors have individual frequency weightings (A, Cand L). Time weightings (F, S and I) are availablesimultaneously in both RMS detectors.

    Symbol Key (for measurementparameters):X: Frequency weighting A, C or L (Note 1)V: Frequency weighting C or LY: Time weighting F, S and I (Note 2)Q: Exchange rate 4 or 5 dBN: 1 to 99% (Note 4).

    Normal Logging Mode

    Detector 1

    RMS

    Detector 2

    RMS

    LXeq

    LXleq

    LXYmax

    LXYmin

    LAFTm5

    LAFavQ

    LASavQ

    LXYN (1 to 99%),

    (Note4

    AUX1 (Note 3)

    AUX2 (Note 3)

    Overload%

    Underrange%

    Detector 1

    RMS

    Detector 2

    Peak

    LXeq LVpkmax

    LXleq No. of Peaks

    LXYmax

    LXYmin

    LAFTm5

    LAFavQ

    LASavQ

    LXYN (1 to 99%),

    (Note 4)

    AUX1 (Note 3)

    AUX2 (Note 3)

    Overload%

    Underrange%

    Instantaneous (display only)

    LXYinst

    LXYp

    LVpk

    Elapsed Time

    Start Time

    Start Date

    Time

    Log no.

    Short Logging Mode

    Detector 1

    RMS (not used)

    Detector 2

    RMS

    LXeq

    AUX1 (Note 3)

    AUX2 (Note 3)

    Instantaneous (display only)

    Elapsed Time

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    47/74

    Chapter 6 Specifications

    BB1125 11 6 32238 MediatorLogging SLM Software BZ 7124

    User Manual

    Detectors:Simultaneous detection of RMS and Peak withindependent frequency weightings

    RMS Detectors:Time Weighting: The RMS detector facilitatesthree exponential time weightings (Fast, Slow, Im-pulse) according to IEC 651 Type 1 (factory

    checked to meet Type 0)Frequency Weightings:A, C or L (also 1/1 and1/3-octave bands with 2238 A F)

    Peak detector:L-weighting: Conforms to IEC651 and IEC1672C-weighing: Conforms to IEC 1672Rise Time

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    48/74

    Chapter 6 Specifications

    6 4 Brel & Kjr2238 MediatorLogging SLM Software BZ7124

    User Manual

    Aux 1 Output:Connector: 2-pin LEMO. Can be used as an ACoutput or a DC input for an external signal

    AC Output:Output Signal: Range-adjusted AC output, L-weighted (Normal and Short logging mode) or withthe frequency weighting selected on the RMS de-tector (Normal logging mode only). Short-circuitprotectedOutput: 1 V RMS corresponding to full-scale indi-cationMax. Load:10k ||1nFOutput Impedance:Typically 100

    DC Input:Voltage Range:0 to 4VResolution: 5 mV(800 steps)

    Aux 2 Output:Connector: 2-pin LEMO. Can be used as a DCoutput, a DC input for an external signal, a triggerinput or a trigger output

    DC Output:Output Signal:DC version of signal on RMS de-tector 1 ( Fast, Inst). Delayed 0.8s. Short-circuitprotectedOutput: 0 to 4.0V DC, (50mV/dB)Update Rate: 160 times per secondMax. Load:10k ||1nFOutput Impedance:Typically 100

    DC Input:Voltage Range:0 to 4VResolution: 5 mV(800 steps)

    Trigger Input:Voltage Range:0 to 4VTrigger Level: 2V

    Trigger Output:Trigger Output:Pause: 0V, Measuring: 4 V

    6.2 Additional Specifications for2238 A F (Version withFilter Set Installed)

    Standards:Conforms with the following: EN61260/IEC1260 (1995) Octave and 1/3-oc-

    tave Bands Class 1 ANSIS1.11 1986 Octave and 1/3-octave

    Bands, Order 3, Type 1-D. Optional Range

    Octave and1/3-octave BandFilters:Conform to IEC1260 (1995) and ANSIS1.111986.

    Frequency Rating System:Base 10Reference Attenuation:0 dBLinear Operating Range: As Indicator rangeNominal Octave Band Centre Frequencies:31.5 Hz, 63 Hz, 125Hz, 250Hz, 500Hz, 1kHz,2 kHz, 4kHz, 8kHzNominal 1/3-octave Band Centre Frequencies:20Hz, 25Hz, 31.5 Hz, 40Hz, 50Hz, 63Hz, 80Hz,100Hz, 125Hz, 160Hz, 200Hz, 250Hz, 315 Hz,400Hz, 500Hz, 630Hz, 800Hz, 1kHz, 1.25kHz,1.6kHz, 2 kHz, 2.5kHz, 3.15kHz, 4 kHz, 5 kHz,6.3kHz, 8 kHz, 10kHz, 12.5kHz

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    49/74

    Chapter 6 Specifications

    BB1125 11 6 52238 MediatorLogging SLM Software BZ 7124

    User Manual

    CE-mark indicates compliance with: EMC Directive.

    EMC Emission EN 500811:Generic emission standard. Part 1: Residential, commercial and light

    industry.

    EN 500812:Generic emission standard. Part 2: Industrial environment.

    CISPR 22:Radio disturbance characteristics of information technology equipment.

    Class B Limits.

    FCC Rules, Part 15:Complies with the limits for a Class B digital device.

    EMC Immunity EN 500821:Generic immunity standard. Part 1: Residential, commercial and lightindustry. RF immunity implies that sound level indications of 50 dB or greater willbe affected by no more than 0.5dB.EN 500822: Generic immunity standard. Part 2: Industrial environment. RF im-munity implies that sound level indications of 65 dB or greater will be affected byno more than 0.5dB.

    These levels of immunity are 9dB better than required by IEC1672.

    Note: The above conformance is guaranteed only when using the included/optional accessories.

    Brel& Kjr reserves the right to change specifications and accessories without notice

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    50/74

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    51/74

    BB1125 11 7 12238 MediatorLogging SLM Software BZ 7124

    User Manual

    Chapter 7

    Appendix 1: General

    7.1 List of Default Parameters ............................................. 7 2

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    52/74

    Chapter 7 Appendix 1: General

    List of Default Parameters

    7 2 Brel & Kjr2238 MediatorLogging SLM Software BZ7124

    User Manual

    7.1 List of Default Parameters

    Note:These default parameters are in addition to those de-scribed in the Basic User Manual.

    Menu Set-up Parameter Default Value

    Log. PeriodPeriod Time Normal

    Logged Every 00:30

    Log. ControlDestination File

    Meas. Time Continuous

    Weightings

    Bandwidth (Detector 1) Broad Band

    Freq. Wgt. (Detector 1) A

    Bandwidth (Detector 2) Broad Band

    Weighting (Detector 2) Peak/C

    Parameters(Normal logging mode)

    1 LAeq

    2 LAFmax

    3 LAFmin

    4 LCpkmax

    5 ... 12 None

    Parameters

    (Short logging mode)

    1 LCeq

    2 ... 3 None

    Input/Output

    Aux 1 AC Output

    Aux 1: Freq. Wgt. Linear

    Aux 2 DC Output

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    53/74

    Chapter 7 Appendix 1: General

    List of Default Parameters

    BB1125 11 7 32238 MediatorLogging SLM Software BZ 7124

    User Manual

    Statistics Percentiles: LN

    L1, L5, L10, L50,

    L90, L95, L99

    Time Weighting F

    Menu Set-up Parameter Default Value

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    54/74

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    55/74

    BB1125 11 8 12238 MediatorLogging SLM Software BZ 7124

    User Manual

    Chapter 8

    Appendix 2: Interface

    8.1 Controlling Mediator via the Serial Interface........ 8 2

    Commands ......................................................................... 8 2Avail_Time? ....................................................................... 8 3Bandwidth_Short .............................................................. 8 3Frequency_Weighting_2.................................................... 8 5Frequency_Weighting_Short ............................................ 8 6PArameter?........................................................................ 8 7SEtup ................................................................................. 8 9

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    56/74

    Chapter 8 Appendix 2: Interface

    Controlling Mediator via the Serial Interface

    8 2 Brel & Kjr2238 MediatorLogging SLM Software BZ7124

    User Manual

    8.1 Controlling Mediator via theSerial Interface

    8.1.1 Commands

    The command and query messages available with the Loggingmodule are listed in Table 8.1. The interface jobs that arespecific for the Logging module are explained in the following.For other interface jobs, refer to the Basic User Manual.

    Message Command Query Message Command Query

    Avail_Time IDentify

    Bandwidth Key

    Bandwidth_Short

    PArameter

    Continue PAUse

    Error RAnge

    File REset

    Frequency_Weighting_1

    SEtup

    Frequency_Weighting_2

    STatus

    Frequency_Weighting_Short

    SYstem

    Header Version

    Table 8.1 Command and query message overview

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    57/74

    Chapter 8 Appendix 2: Interface

    Controlling Mediator via the Serial Interface

    BB1125 11 8 32238 MediatorLogging SLM Software BZ 7124

    User Manual

    8.1.2 Avail_Time?

    The Avail_Time? query shows how much time remains in

    Mediator memory for storing logging results. The syntax forthe Avail_Time? query and response returned by the Medi-ator appear in Fig. 8.1.

    Example (time query):

    Interface job from controller:Avail_Time?

    From Mediator:

    :AVAIL_TIME HH,MM,SS

    8.1.3 Bandwidth_Short

    The Bandwidth_Short command is used for setting the band-width for Detector 2 in Short logging mode. The syntax isshown in Fig. 8.2.

    The default setting is: Broad-band

    The Bandwidth_Short parameters are: Octave_1, Octave_3and Broad.

    Fig.8.1 Syntax for the Avail_Time?query and Mediator response

    :

    To Mediator

    Te

    980459e

    AVAIL_TIME?

    Time(HH, MM, SS)

    Nr1

    :

    From Mediator

    TeSPVAIL_TIME

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    58/74

    Chapter 8 Appendix 2: Interface

    Controlling Mediator via the Serial Interface

    8 4 Brel & Kjr2238 MediatorLogging SLM Software BZ7124

    User Manual

    Note: The 1/3- and 1/1-octave options are only available whenthe 1/1-octave and 1/3-octave Filter Set is installed in theMediator.

    The syntax for the query Bandwidth_Short?and the responsereturned by the Mediator appears in Fig. 8.3.

    Example(setting Detector 2 to 1/3-octave):

    Interface job from controller:

    Bandwidth_Short Octave_3

    Query from controller:

    Bandwidth_Short?

    From Mediator:

    :BANDWIDTH_SHORT OCTAVE_3

    Fig.8.2 Syntax for Bandwidth command

    Fig.8.3 Syntax for the Bandwidth_Short?query and Mediator response

    980458e

    Te

    To Mediator

    :BANDWIDTH_SHORT

    BROAD

    OCTAVE_

    O

    CTAVE_3

    SP

    980454e

    Te

    From Mediator

    :

    Bandwidth

    Char

    TeANDWIDTH_S

    HORT?

    B

    ANDWIDTH_S

    HORT

    :

    To Mediator

    SP

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    59/74

    Chapter 8 Appendix 2: Interface

    Controlling Mediator via the Serial Interface

    BB1125 11 8 52238 MediatorLogging SLM Software BZ 7124

    User Manual

    8.1.4 Frequency_Weighting_2

    The Frequency_Weighting_2command is used for setting up

    the frequency weighting options for Detector 2. The syntax isshown in Fig. 8.4.

    The default setting is: Peak and C-weighting

    Peak weighting can be C or L. The frequency weighting values

    for RMS are: A, C or L.

    Note:Some combinations of weightings are mutually exclu-sive for the two detectors.

    The syntax for the query Frequency_Weighting_2? and theresponse returned by Mediator appears in Fig.8.5.

    Example(setting frequency weighting for Detector2 to RMSand A-weighting):

    Interface job from controller:

    Frequency_Weighting_2 Rms_A

    Query from controller:

    Frequency_Weighting_2?

    From Mediator:

    Fig.8.4 Syntax for Frequency_Weighting_2command

    SP

    PEAK_C

    P K_L

    RMS_A

    R

    MS_C

    RMS_L

    980220/1e

    FREQUENCY_WEIGHTING_2?

    From Mediator

    Te:

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    60/74

    Chapter 8 Appendix 2: Interface

    Controlling Mediator via the Serial Interface

    8 6 Brel & Kjr2238 MediatorLogging SLM Software BZ7124

    User Manual

    :FREQUENCY_WEIGHTING_2 RMS_A

    8.1.5 Frequency_Weighting_Short

    The Frequency_Weighting_Short command is used for settingup the frequency weighting options for Detector 2 in Shortlogging mode. The syntax is shown in Fig.8.6.

    The default setting is: C-weighting

    The frequency weighting values are: A, C, Lin, F20, F25,F31_5, F40, F50, F63, F80, F100, F125, F160, F200, F250,F315, F400, F500, F630, F800, F1K, F1K25, F1K6, F2K,F2K5, F3K15, F4K, F5K, F6K3, F8K, F10K, F12K5.

    Note 1:The K is used as decimal separator.

    Note 2: Some combinations of weightings are mutually ex-clusive for the two detectors.

    Fig.8.5 Syntax for the Frequency_Weighting_2? query and Mediator re-sponse

    Fig.8.6 Syntax for Frequency_Weighting_Short command

    980150/1e

    Te

    From Mediator

    :

    Te:

    To Mediator

    Wgt. Value

    Char

    FREQUENCY_WEIGHTING_

    SPREQUENCY_WEIGHTING_

    Parameter

    Char/Nr.

    :

    To Mediator

    Te

    980456e

    FREQUENCY_WEIGHTING_SHORT SP

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    61/74

    Chapter 8 Appendix 2: Interface

    Controlling Mediator via the Serial Interface

    BB1125 11 8 72238 MediatorLogging SLM Software BZ 7124

    User Manual

    The syntax for the query Frequency_Weighting_Short? andthe response returned by the Mediator appears in Fig.8.7.

    Example (setting frequency weighting to A-weighting inShort logging mode):

    Interface job from controller:

    Frequency_Weighting_Short A

    Query from controller:

    Frequency_Weighting_Short?

    From Mediator:

    :FREQUENCY_WEIGHTING_SHORT A

    8.1.6 PArameter?

    The PArameter?query is used for checking the selected meas-urement parameters. The syntax for the query PArameter?and the response returned by Mediator appears in Fig.8.8.

    Example (reading the measured LXeq value):

    Query from controller:

    PArameter:LEq? A

    Fig.8.7 Syntax for the Frequency_Weighting_Short?query and Mediatorresponse

    980455e

    Te

    From Mediator

    :

    Te:

    To Mediator

    Wgt. Value

    Char

    F

    REQUENCY_W

    EIGHTING_S

    HORT

    SPREQUENCY_WEIGHTING_SHORT

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    62/74

    Chapter 8 Appendix 2: Interface

    Controlling Mediator via the Serial Interface

    8 8 Brel & Kjr2238 MediatorLogging SLM Software BZ7124

    User Manual

    Fig.8.8 Syntax for the PArameter?query and Mediator response

    Sub Header

    Frequency

    WeightingSetting

    Time

    WeightingSetting

    ELapsed

    Inst AC

    LinOctave

    FastSlow

    Impulse

    LEq ACLin

    Octave

    LIeq AC

    LinOctave

    LMAx A

    CLin

    Octave

    FastSlow

    Impulse

    LMIn AC

    LinOctave

    FastSlow

    Impulse

    Table 8.2 Sub-header and parameter settings for the PArameter?query

    980460e

    PA

    RAMETER

    PA

    RAMETER

    Sub Header?

    See tableSee table

    See text

    See table

    TeFrequencyWeightingParameter

    TimeWeightingParameter

    : :

    Sub Header:

    To Mediator

    Te

    From Mediator

    :

    Parameter

    NR2

    SP

    SP

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    63/74

    Chapter 8 Appendix 2: Interface

    Controlling Mediator via the Serial Interface

    BB1125 11 8 92238 MediatorLogging SLM Software BZ 7124

    User Manual

    From Mediator (value in dB):

    :PARAMETER:LEQ 52.6

    8.1.7 SEtup

    The SEtup commands are used for setting up most of themeasurement parameters in the Measurement Setting menu.

    SEtup Commands

    The SEtup commands (except for Auto Start) use the syntaxillustrated in Fig. 8.9.

    The syntax for the query SEtup?and the response returnedby Mediator appears in Fig. 8.10.

    LP AC

    LinOctave

    FastSlow

    Impulse

    LPK

    LPKMax

    No_Peaks

    Overload

    Underrange

    Start_Date

    Start_Time

    Sub HeaderFrequencyWeighting

    Setting

    TimeWeighting

    Setting

    Table 8.2 (cont.) Sub-header and parameter settings for the PArameter?

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    64/74

    Chapter 8 Appendix 2: Interface

    Controlling Mediator via the Serial Interface

    810 Brel & Kjr2238 MediatorLogging SLM Software BZ7124

    User Manual

    Fig.8.9 Syntax for the SEtup command

    Sub Header Parameter Comments

    No Setting Type

    Aux_1 OutIn

    CharSets Aux1to AC OutputSets Aux1to DC Input

    Aux_1_FW

    Linear_Frequen-cy_WeightingDetector_1_Freq-uency_Weighting

    Char

    Sets Linear Frequencyweighting for Detector 1output to the Aux 1out-put

    Aux_2

    OutInTrigger_InTrigger_Out

    Char

    Sets Aux2to DC Out-

    putSets Aux2to DC InputSets Aux 2 to TriggerInputSets Aux2to TriggerOutput

    Destination FileInterface

    Char

    Directs the loggingresult to Mediatorsmemory or to the inter-face

    Exchange_Rate 45

    NR1Sets Exchange Rate to4 or 5dB

    Table 8.3 Sub-header and parameter settings for the SEtup command

    980466e

    Te: :

    ,

    SE

    TUP Sub Header

    See tableSee table

    To Mediator

    SP

    If more than one parameter

    Parameter

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    65/74

    Chapter 8 Appendix 2: Interface

    Controlling Mediator via the Serial Interface

    BB1125 11 8112238 MediatorLogging SLM Software BZ 7124

    User Manual

    Log_Meas_Time

    ContinuousPreset

    Char

    Sets continuous meas-urement or selects thepre-defined measure-ment time (total loggingtime)

    Log_Time

    1 (Hour)0 ... 7440

    NR1Sets the overall meas-urement time (total log-ging time)

    2 (Minute) 0 ... 59

    3 (Second) 0 ... 59

    Logged_Every_Normal

    1 (Minute) 0 ... 60

    NR1

    Sets the logging periodfor each logging in aNormal logging meas-urement

    2 (Second) 0 ... 59

    Sub Header Parameter Comments

    No Setting Type

    Table 8.3 (cont.) Sub-header and parameter settings for the SEtup com-mand

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    66/74

    Logging_Param-eter_Normal

    1 Selector 1 ... 12 NR1Selects the position ofthe succeeding parame-ter

    2

    LMAXLMINLTM5LEQLIEQLAVLN01 ... LN07OVERLOADUNDERRANGEPEAKSPKMAXAUX1AUX2L_LOG_NONOPAR

    CharSets the logging param-eters for normal loggingmode

    3 DETector_NoneDETector_1DETector_2

    Char Selects the detector

    4

    FastSlowImpulseNone

    Char Sets the time weighting

    Logging_Param-eter_Short

    1 Selector 1 ... 3 NR1Selects the position ofthe succeeding parame-

    ter

    2

    LEQAUX1AUX2NOPAR

    CharSets the logging param-eters for short loggingmode

    Sub Header Parameter Comments

    No Setting Type

    Table 8.3 (cont.) Sub-header and parameter settings for the SEtup com-mand

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    67/74

    Chapter 8 Appendix 2: Interface

    Controlling Mediator via the Serial Interface

    BB1125 11 8132238 MediatorLogging SLM Software BZ 7124

    User Manual

    N1N2N3N4N5N6N7

    1 ... 99 NR3Sets the percentile lev-els

    Peaks_Over 0 ... 180 NR3Sets the peak countinglevel

    Preset_Time

    1 (Hour)0 ... 99 NR1Sets the measurementtime for each measure-ment in an Auto Startsequence

    2 (Minute) 0 ... 59 NR1

    3 (Second) 0 ... 59 NR1

    PEriod_Time NormalShort

    CharSelects normal or shortlogging mode

    Random_Frontal RandomFrontal Char Sets Random or Frontalfrequency correction

    Recall 0 ... 4 NR1Recall measurementset-up 0 to 4 (0 is defaultset-up)

    SAve 1 ... 4 NR1Saves measurementset-up in memory 1 to 4

    SEquence OFf, ON CharSwitches the Auto Start

    sequence On or Off

    STatistics_Time-weighting

    FastSlowImpulse

    CharSets the time weightingfor the statistics distribu-tion

    Sub Header Parameter Comments

    No Setting Type

    Table 8.3 (cont.) Sub-header and parameter settings for the SEtup com-mand

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    68/74

    Chapter 8 Appendix 2: Interface

    Controlling Mediator via the Serial Interface

    814 Brel & Kjr2238 MediatorLogging SLM Software BZ7124

    User Manual

    Wind_Screen OFf, ON CharSwitches the wind-screen frequency cor-rection On or Off

    Fig.8.10 Syntax for the SEtup?query and Mediator response

    Sub Header

    Aux_1?

    Aux_1_FW?

    Aux_2?

    Destination?

    Exchange_Rate?

    Log_Meas_Time?

    Log_Time?

    Table 8.4 SEtup queries

    Sub Header Parameter Comments

    No Setting Type

    Table 8.3 (cont.) Sub-header and parameter settings for the SEtup com-mand

    980216/1e

    Te

    To Mediator

    : :ETUP

    Te

    From Mediator

    :

    Sub Header?

    See table

    :ETUP Sub Header

    See table

    ParameterSP

    ,

    If more than one parameter

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    69/74

    Chapter 8 Appendix 2: Interface

    Controlling Mediator via the Serial Interface

    BB1125 11 8152238 MediatorLogging SLM Software BZ 7124

    User Manual

    Example (checking the Preset Time set to 10 minutes):

    Query from controller:

    SEtup:Preset_Time?

    From Mediator:

    :SETUP:PRESET_TIME 0,10,0

    Logged_Every_Normal?

    Logged_Every_Short?

    Logging_Parameter_Normal?

    Logging_Parameter_Short?

    N1 ... N7?

    Peaks_Over?

    Preset_Time?

    Period_Time?

    Random_Frontal?

    SEquence?

    STatistics_Timeweighting?

    Wind_Screen?

    Sub Header

    Table 8.4 (cont.) SEtup queries

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    70/74

    816 Brel & Kjr2238 MediatorLogging SLM Software BZ7124

    User Manual

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    71/74

    BB1125 11 9 12238 MediatorLogging SLM Software BZ 7124

    User Manual

    Chapter 9

    Index

    A

    AC Output ..........................................310, 64Application

    programs.................................................. 22Auto Start............................................. 44, 63

    set-up ....................................................... 44Aux 1............................... 16, 310, 311, 64

    AC Output .............................................310DC Input ................................................ 310

    Aux 2.......................................... 1 6, 310, 64DC Input ................................................ 311DC Output .............................................311Trigger Input ......................................... 311Trigger Output ...................................... 311

    AUX1 .................................................. 18, 110AUX2 .................................................. 18, 110A-weighting ................................................... 15

    BBacklight ....................................................... 24

    pushkey.................................................... 24Bandwidth

    command .................................................83Batteries (saving).......................................... 24Broadband data.................................... 53, 54

    CCalibrate pushkey......................................... 22Calibration

    set-up ....................................................... 52time .......................................................... 52

    Cancel pushkey .................................... 23, 24Command

    Bandwidth ...............................................83Destination ............................................ 810Frequency_Weighting_1 ......................... 8 6Frequency_Weighting_2 ......................... 8 5Log_Every_Normal ............................... 811Log_Time ...............................................811Logging_Parameter_Normal ................ 811Logging_Parameter_Short.................... 811message overview.................................... 82PEriod_Time.......................................... 812SEtup ....................................................... 89

    Aux_1 ...............................................810Aux_1_FW ....................................... 810Aux_2 ...............................................810Exchange_Rate ................................ 810

    Log_Meas_Time............................... 811N1 ... N7........................................... 812Peaks_Over...................................... 812Preset_Time..................................... 812Random_Frontal.............................. 812Recall ...............................................812SAve ................................................. 812SEquence ......................................... 812STatistics_Timeweighting .............. 812Wind_Screen.................................... 812

    Continuous mode .......................................... 34Controlling Mediator via the interface ........8 2Cursor keys ................................................... 22

    C-weighting ................................................... 15

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    72/74

    Index

    9 2 Brel & Kjr2238 MediatorLogging SLM Software BZ7124

    User Manual

    D

    DAT recorder ...............................................311Data

    files menu .................................................22

    Files pushkey ...........................................22DCInput...................................310, 311, 64Output ...........................................311, 64

    Decimal separator .........................................86Default parameters .......................................72Destination ....................................................34Detector 1 and 2 ..........................15 , 36, 37Detector setting .............................................39Detectors ..................1 5, 35, 311, 85, 86

    bandwidth .......................................36, 37frequency weighting .......................36 , 37

    EElapsed time ........ 1 9, 110, 112, 113, 53EMC ...............................................................65External

    DC supply...............................................312trigger.....................................................311

    F

    Fast (F)...........................................................15File

    Manager ..........................................15, 22setting.......................................................34

    size............................................................34File_Space? query ..........................................83Filter set.......................................36, 37, 84Fixed logging period .............................14, 33Frequency weighting .......15, 17, 111, 35,

    37, ...................................................311, 85Frequency_Weighting_1 command...............86Frequency_Weighting_1? query ...................87Frequency_Weighting_2 command...............85Frequency_Weighting_2? query ...................85

    GGeneral

    results.......................................................53

    IImpulse (I)......................................................15Info field .........................................................39Input/Output

    function ..................................................310Window...................................................310

    Instantaneous values ....................................43

    LLAFTm5 .........................................................18

    Left/Right Arrow pushkey ............................22

    Linear weighting ...........................................15LN........................................................39, 310Log no.........................................19, 110, 53Log.

    Control Window ..............................33, 42Periods Window .......................................32Logging

    data...........................................................52Normal mode ......................................53Short mode .........................................54

    Measurement Window.............................42Normal .....................................................14parameters ...............................................43period...............................................15, 32Short ................................................14, 83time...........................................................15

    Logging_Parameter_Normal? .....................813Logging_Parameter_Short? ........................813LXeq .............................. 18, 110, 111, 112LXIeq...................................................18, 111LXpk....................................................19, 112LXpkMax ..............................................53, 54LXpkmax.............................................18, 111LXYav4...........................................................18LXYav5...........................................................18LXYinst ...............................................19, 112LXYmax ..............................................18, 111LXYmin ...............................................18, 111LXYN..............................................................18

    MMarker

    1 ... 4 pushkey ..........................................24settings .....................................................44status box ........................................42, 44

    Markers............................... 15, 43, 53, 54Maximum measurement time ......................14Meas. Window pushkey.................................24Measurement

    data..................................................52, 53parameters .............................17 , 62, 89range.........................................................23Result pushkey ........................................23

    settings .....................................................32set-up ........................................................52Set-up menu...........................16 , 22, 32Time..........................................................34Window...................................22, 23, 39

    Memorysize............................................................14space .........................................................15

    Menu items (selecting) ..................................22Microphone (type)..........................................52Minimum measurement time .......................34

    N

    Normal logging ..............................................14

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    73/74

    Index

    BB1125 11 9 32238 MediatorLogging SLM Software BZ 7124

    User Manual

    mode.......................................3 3, 38, 62mode (parameters) .................................. 17

    Number ofloggings .................................................... 14

    peaks ........................... 19, 112, 53, 54

    OOverall

    measurement parameters.............. 1 4, 38Measurement Window ............................4 2results ............................................. 52, 54

    Overload ...................................... 52, 53, 63Overload% ............................... 18, 111, 113

    PParameter...................................................... 17

    default...................................................... 72Elapsed? query ........................................ 88Inst? query............................................... 88LEq? query ..............................................88LIeq? query..............................................88LMA? query .............................................88LMIn? query ............................................88LP? query.................................................89LPK? query..............................................89LPKMax? query ...................................... 89No_Peaks? query ..................................... 89Overload? query ...................................... 89selecting ................................................... 22set-up ....................................................... 39text ...........................................................13Underrange? query ................................. 89

    PArameter? query ......................................... 87Parameters Window ..................................... 38Pause

    Continue pushkey ................................... 23mode......................................................... 22

    Peakdetector data................................... 53, 54weighting .................................................85

    Percentile levels ................................. 17, 310Period Time .......................................... 32, 33Power pushkey ..............................................22Printing data .................................................54Pushkeys

    Backlight .................................................24Calibrate .................................................. 22Cancel ............................................. 23, 24Data Files ................................................ 22definitions ................................................ 22Left/Right Arrow ..................................... 22Marker 1 ... 4 ...........................................24Meas. Result ............................................23Meas. Window ......................................... 24Pause/Continue ....................................... 23pictograms ...................................... 13, 22

    Power ....................................................... 22

    Range ....................................................... 23Reset ........................................................ 23Select............................................... 23, 24Set-up....................................................... 22

    System ..................................................... 22Up/Down Arrow....................................... 22

    QQuery

    Destination? .......................................... 813File_Space? ..............................................83Frequency_Weighting_1?........................8 7Frequency_Weighting_2?........................8 5Log_Meas_Time? ................................... 813Log_Time? ............................................. 813Logged_Every_Normal? ........................ 8 13Logged_Every_Short? ........................... 8 13

    message overview.................................... 82Parameter

    Elapsed?.............................................88Inst? ................................................... 88LEq? ................................................... 88LIeq? .................................................. 88LMA?.................................................. 88LMIn?.................................................88LP? ..................................................... 89LPK? .................................................. 89LPKMax? ...........................................89No_Peaks?.......................................... 89Overload? ...........................................89Underrange? ...................................... 89

    PArameter?..............................................87SEtup

    Aux_1?.............................................. 813Aux_1_FW? ...................................... 813Aux_2?.............................................. 813Exchange_Rate? .............................. 813N1 ... N7? ......................................... 813Peaks_Over? .................................... 813PReset_Time? .................................. 813Random_Frontal? ............................ 8 14SEquence?........................................ 814

    STatistics_Timeweighting?............. 814Wind_Screen? .................................. 814

    SEtup? ..................................................... 89

    RRange pushkey ..............................................23Remaining time.............................................14Reset pushkey ...............................................23RMS detector...............................................311

    SSaved data ..................................................... 52

    Select pushkey ..................................... 23, 24

  • 7/21/2019 Bruel&Kjaer-2238 Logging Slm Software

    74/74

    Index

    SelectingMeasurement Window.............................42menu items...............................................22parameters ......................................22, 38

    Sensitivity value ............................................52Serial number ................................................52Setting

    logging control..........................................33logging periods .........................................32

    Setting upAux 1 ......................................................310Aux 2 ......................................................311bandwidth for Detector 1 ...............36, 37Destination...............................................34frequency weighting ...35, 36, 37, 311input/output function ............................310measurement range.................................23Measurement Time..................................34Mediator to start automatically..............44percentile levels .....................................310Period Time ..............................................32statistics parameters ...............................39time weighting ................................35, 39

    SEtupAux_1 command.....................................810Aux_1? query .........................................813Aux_1_FW command.............................810Aux_1_FW? query..................................813Aux_2 command.....................................810Aux_2? query .........................................813command ...........................................