BROOKFIELD CT3 TEXTURE ANALYZER - Cole-Parmer

Brookfield Engineering Labs., Inc. Page � Manual No. M/08-37�A0708

SPECIALISTS IN THE

MEASUREMENT AND

CONTROL OF VISCOSITY

TEL 508-946-6200FAX 508-946-6262

or 800-628-8139 (USA excluding MA)INTERNET http://www.brookfieldengineering.com

BROOKFIELD ENGINEERING LABORATORIES, INC.11 Commerce Boulevard, Middleboro, MA 02346 USA

with offices in: Boston • Chicago • London • Stuttgart • Guangzhou

BROOKFIELD CT3

TEXTURE ANALYZER

Operating Instructions

Manual No.M/08-37�A0708


TABLE OF CONTENTS

I. INTRODUCTION.................................................................................................................................................................................... 3I.1 Components .................................................................................................................3I.2 Utilities ........................................................................................................................4I.3 Units .............................................................................................................................4I.4 Specifications ...............................................................................................................4I.5 Installation ...................................................................................................................5I.6 Safety Symbols and Precautions ..................................................................................6I.7 Key Functions ..............................................................................................................7I.8 Cleaning .......................................................................................................................8

II. QUICK START......................................................................................................................................................................................... 9

III. OPERATION...................................................................................................................................................................................... �0III.1 Principle .......................................................................................................................10III.2 Emergency Stop ...........................................................................................................10III.3 Base Table ....................................................................................................................11III.4 Probes ...........................................................................................................................12III.5 Fixtures ........................................................................................................................12III.6 Operating Menu ...........................................................................................................12III.7 Running A Test .............................................................................................................15III.8 Texture Loader Software ..............................................................................................21 III.9 Checking Calibration ...................................................................................................22

IV. TEST METHOD DEVELOPMENT............................................................................................................................................... �4IV.1 Sample Preparation ......................................................................................................24IV.2 Test Probe / Fixture ......................................................................................................24IV.3 Test Parameters.............................................................................................................25IV.4 Recommendations ........................................................................................................25

V. APPLICATIONS................................................................................................................................................................................ �6V.1 Comparison of Low Fat and Virtually Fat Free Yogurt Consistencies ..........................26V.2 A Comparison of the Textural Characteristics of Biscuits (Cookies) ............................29V.3 Review of Solid Chocolate Tablet at Ambient Temperature ........................................31

Appendix A - Probes, Fixtures, Calibration Accessories and Gelatin Accessories ........................34A-1 Probes ...........................................................................................................................34A.2 Fixtures..........................................................................................................................38A.3 Calibration Accessories .................................................................................................41A.4 Gelatin Accessories .......................................................................................................41

Appendix B - Troubleshooting....................................................................................................43Appendix C - Texture Loader Programming ..............................................................................44Appendix D - CT3 to Computer Command Set ..........................................................................46Appendix E - Warranty and Repair Service ................................................................................47

Brookfield Engineering Labs., Inc. Manual No. M/08-37�A0708

I. INTRODUCTION

The CT3 Texture Analyzer is the most recent development of the original Boucher Jelly Tester. The original product was created as the Stevens Texturemeter and evolved into the CNS Farnell LFRA TA (LeatherheadFoodResearchAssociationTextureAnalyzer).BrookfleldEngineeringfirstenhancedthe design of the LFRA, maintaining the characteristics of the original equipment, while expanding its measurement capabilities and ease of use by incorporating modern digital technology.

ThenewBrookfieldCT3TextureAnalyzeristhethirdgenerationofthisvenerableproduct,addingtension testing capability, increased load cell options, space for large samples, two options for base tablesandawiderrangeofaccessoriesformoreflexibility.Themainobjectiveistocharacterizeyour samples in a way that best represents their perception by human senses. This is the essence of texture analysis.

TheprincipleofoperationoftheCT3TextureAnalyzeristosubjectasampletocontrolledforcesin compression using a probe, or in tension using grips. The resistance of the material to these forces is measured by a calibrated load cell and shown in either grams or Newtons. These forces are a function of the properties of the sample and the parameters of the test method.

TherearefiveloadcellrangesavailablefortheCT3TextureAnalyzerofferedbyBrookfield:

Model Load Cell Range CT3-100 0.1kg or 100gCT3-1000 1.0kgCT3-1500 1.5kgCT3-4500 4.5kgCT3-10k 10.0kg

I.� Components

Please check to be sure that you have received all components, and that there is no damage. If youaremissinganyparts,pleasenotifyBrookfieldEngineeringoryourlocalBrookfieldagentimmediately. Any shipping damage must be reported to the carrier.

Component Part Number Quantity

CT3 Texture Analyzer varies 1Operating Manual M08-371 1USB Cable DVD-202 1Power Cord 1 115 Volt or DVP-65 1 230 Volt DVP-66 TextureLoader CD CD Prog A 1Probe Adapter M6 to M3 Threads TA51 1

OptionalProbe varies per orderTemperature Probe DVP-94Y 1Rotary Base Table TA-RT-KIT 1Fixture Base Table TA-BT-KIT 1Bloom Strip CT3-CS-100 or 1 CT3-CS-1000Calibration Weight Set (TA-”varies”-100C, -1000C, -1500C, -4500C, -10kgC) 1Standard Probe Kit TA-P-KIT2 1TexturePro CT Software TA-CT-PRO 1

NOTE: Optionalcomponentsmayincludeprobesorfixtures.SeeAppendixAfordetails.


I.� Utilities

Input Voltage: 90-265 VACInput Frequency: 50/60 HzPower Consumption: 150 VAFuse: Two 4 amp, 5 x 20mm, Time-lag

Power Cord Color Code:. United.States. Outside.United.StatesHot (live) Black BrownNeutral White BlueGround (earth) Green Green/Yellow

Mainsupplyvoltagefluctuationsarenottoexceed±10%ofthenominalsupplyvoltage.

I.3 Units

The CT3 Texture Analyzer uses the SI system of units for all parameters.

Parameter Unit AbbreviationLoad Grams or Newtons g or NDeformation Millimeter mmTime Seconds sSpeed Millimeter per second mm/sWork MilliJoules mJ

I.4 Specifications

Load: Range Resolution Model Grams Grams Accuracy* CT3-100 0-100 0.01 ±0.5%FSR CT3-1000 0-1000 0.10 ±0.5%FSR CT3-1500 0-1500 0.20 ±0.5%FSR CT3-4500 0-4500 0.50 ±0.5%FSR CT3-10kg 1-10000 1.0 ±0.5%FSR FSR = Full Scale Range

*ThisvalueappliestothefullrangeofoperatingtemperaturesasdefinedinSectionI.4Environmental Conditions. Accuracy will be greatly improved when the instrument is operated in a stable ambient temperature.

Trigger Point: Range Resolution Model Grams Grams CT3-100 0.1-10 0.01 CT3-1000 0.2-100 0.10 CT3-1500 0.2-150 0.2 CT3-4500 0.5-500 0.5 CT3-10k 1-1000 1.0

Recommended trigger value settings are given in Table II.1


Speed: 0.01 to 0.1 mm/s in increments of 0.01 mm/s 0.1 to 10 mm/s in increments of 0.1 mm/s Accuracy:±0.1%ofsetspeed

Position: Range: 0-101.6 mm Resolution: 0.1mm Accuracy: 0.1mm

Temperature: -20°C to 120°C (Requires optional probe, DVP-94Y) Output: RS232 Compatible Serial Port, USB Port

Environmental 0°C to 40°C temperature range (41°F to 104°F)Conditions: 20%-80%relativehumidity,non-condensingatmosphere

Use: Intended for indoor use only Altitude: up to 2000m

Dimensions: 10.5” x 10.5” x 24”

Weight: 37 lbs. (16.8 kg)

I.� Installation

1) Prepare a clean, level surface.

NOTE: This instrument is a sensitive load measuring device. It should be installed on a clean, solid, level bench surface which is free from external vibrations.

2) Unpack and remove the CT3 Texture Analyzer from the shipping container.

The CT3 Texture Analyzer weighs 16.8 kg (37 pounds). Use caution when lifting the unit out of the packaging.

3) PlacetheCT3TextureAnalyzeronasturdy,levelsurface.Adjustthefourfeettoensurethat the instrument is stable.

4) Remove any additional components from the shipping package. Save the shipping container and packaging for future use.

5) Install base table using the supplied pair of T-bolts and thumbscrews. Position the base table so that it is approximately centered under the probe. More accurate alignment may berequiredforcertainfixtures.

6) Make sure that the AC power switch at the rear of the CT3 Texture Analyzer is in the OFF

lo

onoff

position. Connect the power cord to the socket on the back panel of the instrument and plug it into the appropriate AC line. Position instrument so that the power cord can be removed easily.

The AC input voltage and frequency must be within the appropriate range as shown on the model and serial tag of the instrument (located on the back of the CT3).


The CT3 Texture Analyzer must be earth grounded to ensure against electronic failure!

7) If appropriate, connect communication cable which is supplied with Texture Loader software to the appropriate port for connection to a computer.

8) TurnthepowerswitchtotheONposition.Thestartupscreenwillindicatethefirmwareversion and load range of the CT3 (Figure I.1).

CT3 VERSION X.XTEXTURE ANALYZER XXXX GRAM UNIT INITIALIZING

Figure I.1

9) Allow the instrument to warm up for 10 minutes.

10) If desired, check calibration according to Section III.8.

I.6 Safety Symbols and Precautions

SafetySymbols

The following explains safety symbols which may be found in this operating manual, or on the instrument itself.

Indicates hazardous voltages may be present.

Refertothemanualinallcaseswherethissymbolisevident.Usedforspecificwarningorcautioninformationtoavoidpersonalinjuryordamagetotheinstrument.

Keep hands, fingers and other body parts clear of moving parts when operatinginstrument.

Functional Earth Terminal - Main power entry module must have an earth conductor.

Precautions

Ifthisinstrumentisusedinamannernotspecifiedbythemanufacturer,theprotectionprovided by the instrument may be impaired.

This instrument is not intended for use in a potentially hazardous environment.

In case of emergency, turn off the instrument and then disconnect the electrical cord from the wall outlet.


The user should ensure that the substances placed under test do not release poisonous, toxicorflammablegasesorliquidsatthetemperatureswhichtheyaresubjectedtoduring the testing.

I.7 Key Functions

The CT3 Texture Analyzer is operated through two keys and a knob located on the keypad. Additionally, there is an emergency stop button located above the base and to the right of the probe rod.

Brookfield

Display

Start

EmergencyStop

Select/ScrollResetStop

Figure I.2

ProbeAdapter

RESET./.STOP This key is used to stop a test in progress and return to starting position.

START This key is used to start the test. During the descent of the probe, prior to the trigger

point, this key can be used to accelerate the rate of descent.

. SELECT./.SCROLL.(see.section.III.6) This knob has multiple functions: 1. The knob is pressed to select the option currently highlighted. 2. The knob is rotated to change the value of the parameter being selected. 3. During a test, pressing this knob will display test parameters. 4. Holding knob depressed while turning on power will switch the load display units

between grams and Newtons.

EMERGENCY.STOP This button is used to abort a test in case of an emergency condition.


1).USB.Type.B.Port

2).RS-232.Serial.Port..

3)..Temperature.Probe.Plug

4). Power.Entry.Module. Power.ON/OFF.Switch

Figure I.3

1) USB TYPE B PORT Use with USB Cable P/N DVP-202 to connect instrument to a computer. Cable USB 2.0 A

Male to B Male. See Appendix D, (CT3 to Computer Command Set)2) RS-232 Serial Port Use with RS-232 Cable P/N DVP-80 to connect instrument to a computer. See Appendix D, (CT3 to Computer Command Set)3) Temperature Probe Plug - 4 pin plug. Use with Temperature Probe P/N DVP-94Y4) Power Entry Module: ON/OFF switch-fused (see I.2 Utilities). Voltage: 90-265 VAC

I.8 Cleaning

Instrument and Keypad: Clean with a dry, nonabrasive cloth. Do not use solvents or cleaners.

ProbesandFixtures: Probesandfixturesaremadefromavarietyofmaterialsfrom metals (stainless steel, aluminum) to plastics (acrylic, Black Delrin, Nylon). Clean with a nonabrasive cloth using solvents that are appropriate for both the sample materialandthematerialoftheprobeand/orfixture.

Donotapplyexcessiveupward,downwardorsidewaysforcetoprobewhilefixedtoCT3. Damage may occur to the load cell.

.BACK PANEL


II. QUICK START

1. Unpack the instrument according to Section I.5.

2. Install base table in accordance with the instruction sheet that is enclosed with the base table.Placethesampleonthebasetable.Adjustthetableheightsothatthesurfaceofthe sample is within 5 mm of the probe.

3. Attach the selected probe. See Section IV.2 for more information.

4. Set the test mode to Normal. Please review section III.6 for detailed explanation of operation of Select/Scroll knob.

5. Set the trigger value as recommended below.

Load Cell Recommended Minimum Trigger Value

100g 0.5g1000g 2g1500g 3g4500g 4.5g10kg 10g

Table II.1

6. Set the test speed and distance. See Section IV.3 for more information.

7. Press the START button. The weight of the probe will autozero and then the test will start.

8. Record all test results.

9. Remove sample and clean the probe.

Brookfield Engineering Labs., Inc. Page �0 Manual No. M/08-37�A0708

III. OPERATION

III.� Principle

TheBrookfieldCT3TextureAnalyzercanbeoperatedineithercompressionortensionmodes.

In compression mode a probe moves slowly at pretest speed until a threshold value (the trigger) is reached. The probe then moves a set distance at a set speed into the sample material that is placed(orfixed)onthebasetable.Theloadiscontinuouslymonitoredasafunctionofbothtimeand distance until the probe again returns to its starting position.

In tension mode the sample is typically held between a pair of grips. The test starts when the trigger load is reached as the grips move apart. The load resistance as the sample is stretched or pulled apart is recorded as a function of both time and distance.

III.� Emergency Stop

The CT3 Texture Analyzer can operate with up to 10,000g (10 kg) of force dependent on load cell. Be sure to place only the sample for test under the probe.

Keep body parts and clothing away from the probe during the test.

The CT3 Texture Analyzer uses applied forces to evaluate a material. The user must take care not to place any body part or clothing in the testing zone while the machine is moving. The CT3 Texture Analyzer is provided with an Emergency Stop Button (see Figure I.2) for use in case of an operational problem.

Pressing the Emergency Stop Button will cause different immediate actions depending upon the type of test in use.

Compression: Pressing Emergency Stop Button during a compression test will:

1) Stop the test in progress and display emergency stop screen.

EMERGENCY STOP

RESET EMERGENCY STOP

Figure III.1

2) The probe immediately returns to the home position.

3) The Emergency Stop condition can be canceled by rotating the Emergency Stop Button clockwise.ThiswillresettheCT3firmwaretothepowerupcondition.

Tension: Pressing Emergency Stop Button during a tension test will:

1) Immediately stop probe movement and display the emergency stop screen.

2) Probe returns to test start position, after resetting the emergency stop.

3) A sequence of menus then leads user back to the home position.

Brookfield Engineering Labs., Inc. Page �� Manual No. M/08-37�A0708

III.3 Base Table

The CT3 Texture Analyzer offers two options for Base Tables on which the test sample is placed. Both tables should be secured to the slotted base of the CT3 with thumbscrews and T-bolts. This designprovidesampleadjustmentside-to-sideandfront-to-backtocorrectlyalignfixturesandposition a wide range of samples for testing.

NOTE:Alwaysbesureallpositionandheightadjustmentsaresecurelylockedbeforestart-ing every test.

Rotary.Base.Table

Fine.Adjustment.Nut

Locking.Knob

Brookfield

Fixture.Base.Table

Brookfield

Figure III.2

See Appendix A forfixtureswhichcanbeusedwitheachBaseTable.

RotaryBaseTableThe Rotary Base Table (P/N TA-RT-KIT) is a disc shaped surface and should always be centered undertheprobewhenconductingcompressiontests.Therearetwomethodsofadjustingtheheight in order to place the sample close to the probe for testing. The locking knob on the base oftheRotaryTableallowsquickheightadjustment;justunlocktheknob,raiseorlowerthetable,thenlockitintoposition.Thetableisalsomountedonathreadedshaftheldsecurelywithafineadjustmentnut.Unlockingthefineadjustmentnutandrotatingthetablewillraiseorlowerthetestsurfacetogiveevenmorerangetotheheightadjustment.

Always hold the Rotary Base Table with one hand while loosening the Locking Knob. This will prevent the Rotary Base Table from falling abruptly to the CT3 housing.

KeepfingersawayfromtheFineAdjustNutwhenloweringtheRotaryBaseTabletopreventapinchinjury.


FixtureBaseTableThe Fixture Base Table (P/N TA-BT-KIT) is a rectangular test surface with a removable center. Manyofthetestfixturesfitintothiscenterareasothistablebecomesthemountingbaseforthesesampletestfixtures.TheFixtureBaseTableissuppliedwithavarietyofextensionlegstosetthetestsurfaceatthecorrectheightforallaccessoryfixtures.Somedisassemblyisrequiredto add or remove extension legs by loosening the Phillips head bolts in the underside of the base table.

III.4 Probes

There are a wide range of probes available for use with the CT3 Texture Analyzer as described in Appendix A. One should always be aware that the probe chosen will have an impact upon the test result. Choice of a probe must be made with consideration toward the purpose of the test and the nature of the sample.

The probes may be cleaned while attached to the CT3. Follow recommendations in Section I.8.

Alwaysattachprobesonlyfingertighttopreventthreaddamage.Donotapplyexcessive upward, downward or sideways force. Damage may occur to the load cell.

Inspect a probe before use for any damage and always handle them carefully as some have sharp points or edges. Most probes require the TA51 thread adapter to attach to the CT3. This adapter is installed at the factory before your instrument was shipped. A few probes and most accessory fixturesrequireremovaloftheprobeadapter.Keepitinasafeplaceasitisneededformostprobes.

III.� Fixtures

TherearearangeoffixturesavailableforusewiththeCT3TextureAnalyzerasdescribedinAppendix A. These devices are designed to hold a sample in place during measurement. Each fixtureisdesignedtoattachtoeithertheRotaryBaseorFixtureBaseTable.Refertotheinstructionsprovidedwiththefixtureforproperinstallation.

NOTE:Brookfieldcandesigncustomfixturestomeetyourapplication.ContactBrookfieldor our authorized dealer for details.

III.6 Operating Menu

The CT3 Texture Analyzer offers six test modes and one calibration mode.

Normal – single compression cycle.Hold Time – compress and hold.Cycle Count – compress sample several times.Bloom – compression test measures gelatin bloom strength.TPA–twocycleTextureProfileAnalysiscompressiontest.Tension – pulls apart a sample using tensile force.Static Load – monitors load while hanging calibration weights.


Each test mode requires parameters to be set. All test mode selection and parameter setting is doneusingtheSelect/Scrollknob(seefigure1.2).Thisknobisbothrotatedanddepressedduringoperation.

NOTE: When setting the test speed, pressing the RESET button will toggle the increments from 0.1mm/s to 1mm/s.

Thespecificparametersrequiredwilldependuponthetypeoftestchosen:

Normal Test requires: trigger, deformation, speedHold Time Test requires: hold time, trigger, deformation, speedCycle Count Test requires: cycle count, trigger, deformation, speedBloomTestrequires: AllparametersarefixedaccordingtoindustrystandardTPA Test requires: trigger, deformation, speedTension Test requires: trigger, deformation, speedStatic Load Test requires: none

These parameters, once set, will be maintained by the CT3 during power down to facilitate re-petitive testing. The test mode used prior to powering down will be presented on the screen at the next power up. A test is started by depressing the start button.

Thetestparametersaredefinedasfollows:

Trigger: The load, in grams, measured by the CT3 to indicate that the probe is in con-tact with the sample. Once the trigger value is reached, the test will begin at the definedspeed.BrookfieldrecommendstriggervaluesasspecifiedinTableIII.1

Deformation: The total downward distance the probe will travel once the trigger value is

reached.

Speed: Thespeedatwhichtheprobewilltravelthespecifieddistance.

Time: Thenumberofsecondsthattheprobewillbeheldatthedefineddistanceduringa Hold Time test.

Count: The number of cycles (Speed and Distance) that will be applied to the sample during a Cycle Count test.

All parameters can be set within the ranges shown in Table III.1.

Load Cell RangeParameter �00g �000g ��00g 4�00g �0kTrigger*. 0.1.–.10g. 0.1.–.100g. 0.2.–.150g. 0.5.–.500g. 1.0-1000gDeformation. 0.1.–.101.6mm. 0.1.–.101.6mm. 0.1.–.101.6mm. 0.1.–.101.6mm. 0.1.–.101.6mmSpeed. 0.01.–.10.mm/s. 0.01.–.10.mm/s. 0.01.–.10.mm/s. 0.01.–.10.mm/s. 0.01.–.10.mm/sHold.Time. 0.–.9999.s. 0.–.9999.s. 0.–.9999.s. 0.–.9999.s. 0.–.9999.sCycle.Count. 0.–.99. 0.–.99. 0.–.99. 0.–.99. 0.–.99*..Minimum.recommended.values.for.trigger.are.shown.in.table.II.1.

TableIII.1


Defineatestbyfirstselectingatestmode.RotatetheSelect/Scrollknobuntiltherequiredtestmodeisdisplayed,thenpresstheSelect/Scrollknobtoconfirmyourchoice.Asthetestmodesaredisplayed,theparametersspecifictothatmodewillbeshownwiththepreviouslyselectedparameters.

Onceatestmodeisselected,thecursorwillmovetothefirstparameter.Youmayeitherselectthat parameter to enter new values by pressing the Select / Scroll knob or you may scroll to the next parameter by rotating the Select / Scroll knob.

Data entry is accomplished by setting each digit individually. For example: to set a value of 57.0 as the target distance, rotate the Select / Scroll Knob until the “D” in “Distance” is blinking. Depress the Select / Scroll knob to get to the tens digit, then rotate the knob to the value 5. Depress the Select / Scroll knob again to get to the ones digit, then rotate the knob to the value 7. Depress the Select / Scroll knob to get to the tenths digit, and depress it again to leave the value at 0.

A data entry of zero in all columns for any parameter will result in that parameter being reset to thepreviousvalue.PressingtheSelect/Scrollknobwithoutfirstrotatingitduringthedataentryprocess will result in a zero being placed in that column. This can expedite the entry of Trigger valuessinceinmostcasesthefirstoneortwocolumnswillbezero(004.0grams).

Display Conventions

The CT3 display contains four lines, but some result screens contain additional lines of information. In order to show more than four lines of information, screens are allowed to scroll usingtheScrollknob.Scrollablescreensareidentifiedbytheèê symbols in the upper right corner of the display. Whenever these symbols appear, the display can be scrolled up or down as indicated to show the lines above or below those presently displayed. In the following section describing test modes, all possible displays are shown. For those having more than four lines, the additional lines are shown in grey textasseeninfigureIII.3.

HARDNESS1: XXXX.X gèêHARDNESS2: XXXX.X gCOHESIVENESS: XXX.XXSPRINGINESS: XX.X mmADHESION: XX.X mJTEMP: XXX.X F

HARDNESS1: XXXX.X NèêHARDNESS2: XXXX.X NCOHESIVENESS: XXX.XXSPRINGINESS: XX.X mmADHESION: XX.X mJTEMP: XXX.X C

Load shown in grams Load show in NewtonsFigure III.3


III.7 Running A Test

A test is initiated by depressing the start button. The operator is reminded to attach a probe, then press start again to zero the weight of the probe and begin the test.

* ATTACH PROBE * PRESS START TO CONTINUE

Figure III.4

Depressing the Select/Scroll knob at any time during the test, or even while test results are displayed,willshowthecurrenttestparameters.Atthecompletionofthetest,thefinalresultswill be displayed until the start button or rest button is pressed. The reset button will return the instrument to the default display where the test mode may be selected. The start button will begin the same test again.

A test may be repeated simply by depressing the start button while viewing test results.

The test may be stopped at any time by using the stop/reset button or by pressing the emergency stop button. We recommend that the stop/reset button be used for normal operation. The emergency top is intended for emergency use only.

It may happen that the instrument overloads during a test. This will happen if the load exceeds 120%oftheloadcellcapacity.Whenanoverloadconditionoccursthedisplaywillshowthefollowing:

TEST TERMINATEDMAXIMUM LOAD REACHEDPRESS RESET FOR MENU

Figure III.5

Depressing the reset button will return to the test mode menu. Correct the reason for the overload and retest.

NORMAL TEST – performs a single compression of the sample then immediately returns to HOME starting position.

The operator sets the trigger value, target deformation (travel distance into the sample) and the test speed using the Normal menu screen:

TEST: NORMALTRIGGER: XXX.X gDEFORMATION:XXX.X mmSPEED: X.XX mm /s

Figure III.6


A normal test performs a single compression cycle when the operator depresses the start button. Beginning at the position where the trigger load is measured, the probe descends at the programmed test speed to the target deformation, then returns immediately to home/starting position. Return travel speed is 4.5mm/s. During the test the running screen is seen as shown below:

TEST: NORMALDEFORMATION:XXX.X mmLOAD: XXXX.X g

Figure III.7

Deformation and Load will remain live displays during the test.

Test results are shown on the reporting screen:

PEAK LOAD: XXXX.X gêèDEF@PEAK: XXX.X mmWORK: XXXX.X mJFINAL LOAD: XXXX.X gTEMP: XXX.X F

Figure III.8Peak load is reported as the maximum measured load during the test.

Deformation at peak is the distance to which the sample was compressed when the peak load occurred.

Workisdefinedastheareaunderthecompressionstrokeandisreportedinmilli-Joules.Finalloadistheloadatmaximumdeformation.Oftenthepeakloadandfinalloadwillbethesame value.

HOLD TIME TEST - performs a single compression of the sample. The sample remains compressed for programmed hold time before the probe returns to starting position.

The operator sets the hold time, trigger value, target deformation and test speed using the Hold Time menu screen:

TEST:HOLD TIME: XXXX STRIGGER: XXX.X gDEFORMATION: XXX.X mmSPEED: XX.X mm/S

III.9

A hold time test performs a single compression cycle when the operator depresses the start button. The test runs at the programmed test speed to the target deformation, then holds at this position while monitoring sample load for the programmed hold time. The countdown clock shows remaining hold time. During the test, the running screen is seen as shown below:


TEST:HOLD TIME: XXXXSDEFORMATION:XXX.X mmLOAD: XXXX.X g

III.10

Deformation and Load will remain live displays during the test. When the countdown clock reaches zero, the probe returns to home/starting position at 4.5mm/s.


HOLD TIME: XXXX SèêPEAK LOAD: XXXX.X gDEF@PEAK: XXX.X mmFINAL LOAD:XXXX.X gTEMP: XXX.X F

III.11

Peak load usually occurs at the target deformation, but may occur before the target is reached. Final load is the load recorded at the end of the hold time and is usually lower than the peak due to sample relaxation.

CYCLE COUNT TEST – performs a programmed number of compression cycles upon a sample.

The operator sets the number of cycles, trigger value, target deformation and test speed using the Cycle Count menu screen:

TEST: CYCLE COUNT: XXXXTRIGGER: XXX.X gDEFORMATION :XXX.X mmSPEED: XX.X mm/s

III.12

When the operator depresses the start button, the cycle count test performs multiple compressions on a sample at the programmed test speed to the target deformation, then returns immediately to home/starting position. Return travel speed for each cycle is the same as compression speed.

During the test the running screen is seen as shown below:

TEST: CYCLE COUNT: XXDEFORMATION: XXX.X mmLOAD: XXXX.X g

III.13


Cycle count will show a count down of the number of cycles remaining. Deformation and Load will remain live displays during the test.


CYCLE:XX êèPEAK MEAN: XXXX.X gPEAK STDEV: XXXX.X gPEAK LOAD: XXXX.X gFINAL LOAD: XXXX.X gTEMP: XXX.X F

III.14

Mean and standard deviation of all peaks is reported. Peakloadisthehighestpeakandfinalloadisthepeakloadofthelastcycle.Temp shows temperature at time of last cycle peak, only if probe is connected.

BLOOM TEST – performs a single compression cycle using industry established test parameters and reports gelatin bloom strength.

DeformationandtestspeedarefixedintheBloomTestspecification.

TEST: BLOOMTRIGGER: 4.5 GDEFORMATION: 4.0 mmSPEED: 0.5 mm/s

III.15

When the operator depresses the start button the Bloom test performs a single compression cycle at 0.5mm/s to the target deformation of 4mm. During the test the running screen is seen as shown below:

TEST: BLOOMDEFORMATION:XXX.X mmLOAD: XXXX.X g

III.16

Both Deformation and Load displays are live during the test. The probe then returns immediately to home/starting position at 4.5mm/s.


BLOOM LOAD: XXXX.X gTEMP: XXX.X F

III.17


Bloom load in grams is generally reported as “grams bloom”

NOTE: It is not recommended to conduct bloom testing with load cells greater than 1500g.

TPA TEST–performstwocompressioncyclesonthesampleandreportsfiveestablishedTextureProfileAnalysisresults.

The operator sets the trigger value, target deformation (travel distance into the sample) and the test speed using the TPA menu screen:

TEST:TPATRIGGER: XXX.X gDEFORMATION: XXX.X mmSPEED: XX.X mm/s

III.18

The operator depresses the start button to begin the test. In a TPA test the compression and return strokes of both cycles occur at the programmed test speed. Target deformation for both cycles begins atthetriggerpositionofthefirstcycle.


TEST: TPA CYCLES: 02DEFORMATION: XXX.X mmLOAD: XXXX.X g

III.19TPA cycles will count down to show the number of cycles remaining. Deformation and Load will remain live displays during the test.


HARDNESS1: XXXX.X gêèHARDNESS2: XXXX.X gCOHESIVENESS: XXX.XXSPRINGINESS: XX.X mmADHESION: XXXX.X mJTEMP: XXX.X F

III.20

Hardness1isthepeakloadofthefirstcompressioncycle.Hardness2 is the peak load of the second compression cycle.

Cohesiveness is the ratio of A2/A1. A2 is the area under the compression stoke of the second cycle andA1istheareaunderthecompressionstokeofthefirstcycle.Ifthestructureofthesampleiscompletelydestroyedonthefirstcompression,thisratioiszero.Ifthesampleisperfectlyelasticandnotdamagedatallbythefirstcompressionthisratiois1.0Mostfoodproductswillfallsomewherein between 0 and 1.


Springiness is a measure of how far the sample returns after being compressed to the target deformation.

Adhesiveness is a measure of stickiness and is calculated as the area under the negative peak as probewithdrawsafterthefirstcompression.

TENSION TEST–thistestcanbeusedtopullapartasample,usuallyusinggripfixturestoapply tension load on the sample.

The operator sets the trigger value, target deformation and the test speed using the Tension menu screen:

TEST: TENSIONTRIGGER: XXX.X gDEFORMATION:XXX.X mmSPEED: XX.X mm/s

III.21

After pressing Start the operator is presented with this reminder screen:

*ATTACH TENSION FIXTURES *PRESS START TO CONTINUE

III.22

BesuregripsorothersamplefixturesaresecureandalignedthenpressSTART.TheScroll/Selectknobnowbecomesatoolforadjustingthepositionofthegripssothatthesamplecanbeclamped.Rotate knob to move 1mm/click or hold knob down to descend at 4.5mm/s:

*ADJUST POSITION USING SCROLL/SELECT *PRESS STARTDEFORMATION:XXX.X mm

III.23

The deformation value shown in this screen is the current distance from the top Home position and as such shows how much travel is possible once the test begins. Be sure this value is greater than the sum of the distance necessary to reach the trigger plus the programmed target deformation.

When clamping the sample try to exert only minimal lateral loads on the probe shaft. Pressing Start as shown below will start the test:

*CLAMP SAMPLE *PRESS START TO CONTINUE

III.24



TEST: TENSIONDEFORMATION:XXXX.X mmLOAD: XXXX.X g

III.25

Deformation and Load will remain live displays during the test. When deformation reaches the target value, the test stops.


PEAK LOAD: XXX.X gêèDEF@PEAK: XXX.X mmWORK: XXXX.X mJFINAL LOAD: XXXX.X gTEMP: XXX.X F

III.26

Peak load is the maximum load measured during the test. Temperature at peak load is only shown if temperature probe is used.

Def@Peak is the sample deformation at the peak load. The trigger position is the zero deformation reference point.

Workistheareaundertheloadcurveandismeasuredinmillijoules.

Final load is the load at the target deformation.

NOTE: It is not possible to perform tension tests with the 100g load cell.

III.8 TEXTURE LOADER SOFTWARE (See Appendix C for details)

Texture Loader software was supplied with your CT3 on the bundled software CD. After installing this software into a computer you can add up to 10 additional test programs to the CT3 menu based upon any one of the test methods described above. For example, suppose you routinely test rye bread using a TPA test with a trigger value of 5g, deformation of 18mm and a test speed of 3mm/s. You can create a test called RYE with these test parameters. After downloading this test to the CT3, you will see the RYE test appear in the display as you scroll through the test methods. The Texture Loader program is supplied as a convenience for our customers who routinely run tests with established parameters.


III.9 Checking Calibration

TheloadcalibrationoftheCT3TextureAnalyzercanbeverifiedusingtheStaticLoadmode.WerecommendthatyouusetheBrookfieldweightsetappropriateforyourCT3loadrange:

BELPartNo. LoadRange •TA-CW-100C 100 gram •TA-CW-1000C 1000 gram •TA-CW-1500C 1500 gram •TA-CW-4500C 4500 gram •TA-CW-10KGC 10kg

Thefrequencyofthecalibrationverificationshouldbesetinaccordancetoyourcompanyprocedures.

Startthecalibrationverificationprocessusingtheselect/scrollknobtosetthetestmodetoStaticLoad and press the start button. The display will request that you attach the hanger mount to the probe shaft.

TEST: STATIC LOAD*ATTACH HANGER MOUNT *PRESS START TO CONTINUE

III.27

The weight of the hanger mount itself will be zeroed by pressing the start button.

TEST: STATIC LOAD*PRESS START TO ZEROLOAD XXXX.X g

III.28The display will change to show static load active parameters once the autozero process is complete.

TEST: STATIC LOADADD HANGER AND MASSLOAD XXXX.X g

III.29

TheHangeristhefirstweighttobefixedtothe Hanger Mount.

Hanger Mount

Primary hanger to which additional mass is added

Figure III.30


NOTE: The Hanger is part of the calibrated weight set, and it has a calibrated weight value. This weight must be included as part of the total weight applied to the load cell.

Attach the desired weight to the Hanger and record the load value from the display. Multiple weights may be attached to the Hanger to achieve a range of test points.

Do not apply excessive upward, downward or sideways force to the Hanger Mount or Hanger while adding or removing weight. This may damage the sensing mechanism of the CT3.

As successive weights are added, the CT3 will show the total weight, which should be within thespecifiedinstrumenttoleranceshownintableIII.2.TheaccuracyoftheCT3isdefinedby the rating of the load cell as detailed in Table III.2. If the CT3 Texture Analyzer produces dataoutsideoftheacceptablerange,contactBrookfieldorourauthorizedrepresentativeforinformationonrepair/calibrationservices(seeAppendixDforBrookfieldlocations).

Load Range Load Accuracy Model Grams. CT3-100g. 0.–.100g. 0.5. CT3-1000g. 0.–.1,000g. 5.0. CT3-1500g. 0.–.1,500g. 7.5. CT3-4500g. 0.–.4,500g. 22.5. CT310kg. 0-10kg. 50

TableIII.2

Example of Calibration Verification

A4500gramCT3TextureAnalyzer,accordingtoTableIII.2,hasanaccuracyof±22.5grams.The spreadsheet shown below can be used to easily evaluate a calibration check using the appropriateBrookfieldcalibrationweightset.

Calibration SpreadsheetCT3 TEXTURE ANALYZER. serial.#..6514047

. . . Load.Cell.Capacity......4500

. #. 1. 2. 3. 4. 5. . Load.Cell.Accuracy

. Mass. 999.84. 994.04. 993.96. 994.05. 497.12. . 22.5g

. Serial.#. 59. 87. 92. 106. 153.. . . Weight. . 1. 999.84. . 1.&.2. 1993.88. . 1,.2.&.3. 2987.84. . 1,.2,.3.&.4. 3981.89. . 1.-.5. 4479.00

.

INSTRUCTIONS FOR USE

The Calibration workbook can be downloaded from our website,www.brookfieldengineering.com

Low.Limit. . High.Limit. Reading. . Difference. 977.34. 999.�. 1022.34. -0.3. 1971.38. �993.�. 2016.38. -0.4. 2965.34. �987.�. 3010.34. -0.3. 3959.39. 398�.�. 4004.39. -0.4. 4456.51. 4479.�. 4501.51. 0.�


IV. TEST METHOD DEVELOPMENT

The measurement results provided by the CT3 Texture Analyzer will be dependent on several factors relating to the sample, the test probe, and the test parameters. A variation on any of these elements may result in a change in measurement results. For good test repeatability it is suggested that a clear and complete test method be developed. The following sections describe theseelements.Brookfieldsuggeststhatyourmethoddevelopmentincludesometrialanderrortesting to determine the best test method for your sample material.

IV.� Sample Preparation

The measurement of texture using the CT3 Texture Analyzer requires contact between the test probe and the sample. The shape and surface of the sample may affect the measurement results. Consider for example an orange: the test of a peeled orange will likely give a different result from the test of a single wedge from the same fruit. This is likely the same for any bulk material when compared to a neatly prepared cube of material. Consideration should be given to the preparation of the sample to facilitate repeatability of the test. For example a material that has a flatsurfaceoffersaconsistentinterfacewiththeprobeevenifthematerialisnotcenteredinthetestfixture.Ifyourtestsampleisuneven,partofthetestmethodcouldbetocut/shape/modifythesamplesuchthatthesampleisflat;consider,forexample,thedifferencebetweenaloafofbread versus a slice of bread.

IV.� Test Probe / Fixture

TheCT3TextureAnalyzermaybeusedwithawidevarietyofprobesandfixtures.Brookfieldoffers a set of standard items while also providing special design services. Each type of probe offersbenefitsforcertainsampletypes.Thefollowingtableprovidessomebasicguidelines.Although this table represents our general experience, it is important to note that there are fewestablishedstandardtestsforphysicalmeasurementsoftexture.Themainobjectiveistocharacterize your material in a way that best represents its perception by human senses. This is the essence of texture analysis.

Probe Type Typical Application

Cylinder. well.defined.samples.with.uniform.surfaces,.. general.purpose,.TPA.(texture.profile.analysis)

Sphere. samples.with.small.scale.variations.on.surface,.. general.purpose

Cone. samples.with.rigid.outer.layer...Also.used.for.. penetrometry.and.spreadability

Wire. used.for.cutting.or.slicing.samples.such.as.cheese

Magness.Taylor. used.for.puncturing,.often.used.for.determining.. ripeness.of.fruit/vegetables

Extrusion.Cell. samples.that.can.be.made.to.flow,.general.purpose

Shear.blades. meat.tenderness

TableIV.1


Withinaprobecategory,variationsofgeometrycanbesignificant.Itmayrequirealargerforceto drive a cone of shallow angle as compared to a cone of steep angle. Similarly, a cylinder of large diameter may require a larger force than a cylinder of small diameter. The selection of the probe (type and size) will affect the test result.

Keephands,fingersandotherbodypartsclearofmovingtestprobeswhen operating instrument.

IV.3 Test Parameters

The CT3 Texture Analyzer will require the setting of several parameters depending upon the test method selected (see Table III.1). In general, the following relationships will hold true for Speed and Distance.

1) The measured load tends to increase as the test speed increases.

2) The measured load tends to increase as the compression distance increases. An exception to this could be a material with an outer layer such as an apple, or one that fractures.

The Trigger Point establishes the minimum load required to begin the test. This is how the CT3 knows when the probe is touching the sample. This parameter should be set to a low value for a material with a very delicate outer layer. Trigger value depends upon you load cell. Minimum recommendations are shown in Table II.2.

The Hold Time allows for monitoring the response of a material as it is held compressed. Normally, an increase in the Hold Time will result in a lower measured value, as the sample relaxes.

The Cycle Count provides a way of working a sample by compressing it repeatedly and monitoring its response.

IV.4 Recommendations

The test results of a texture measurement are very dependent on both sample preparation and the testmethod.Whendevelopingamethod,Brookfieldrecommendsthateachparameterbevariedin turn to determine its effect on the results. (Note: vary only one parameter at a time.) Once this information is considered and a method established, the method should be documented in significantdetail.Thiswillensuregoodrepeatabilityofresultsandgoodcomparisonwithotherswho attempt to duplicate your method.


V. APPLICATIONS

Thisapplicationssectionshouldbeusedasaguidetothedevelopmentoftechniquesspecifictoyour own application and requirements. These notes are empirical in nature. Deviation from the describedtestconfigurations(parametersettings,samplesize,shape,formulation,etc.)willresultin deviations from the observations discussed in each application.

V.� Comparison of Low Fat and Virtually Fat Free Yogurt Consistencies

PRODUCT: Low-fat(1%)andvirtuallyfat-free(0.05%)naturalyogurt

OBJECTIVE: Comparison of textural properties in order to identify differences between protein networks formed as an indication of product creaminess.

BACKGROUND: The textural properties of yogurts are critical in determining consumer preference where variation in fat content of formulation has a direct influenceonthesensorycharacteristicsoftheproduct.TheelevatedSolids Not Fat (SNF) content of low-fat yogurts forms strong casein-casein bonds uncharacteristic in a full-fat yogurt, where homogenized fat globules are partly covered with casein, facilitating protein-protein interactions. Fat becomes trapped within this protein network where it imparts a smooth creamy mouthfeel and spoonable glossy consistency characteristic of full-fat yogurts.

Back Extrusion is an ideal method for the assessment of yogurts and other gelled, semi-solid foods. This compression extrusion test consists of applyingaforcetotheproductuntilitflowsthroughthespacebetweenthe probe perimeter and the container. A wide range of complex forces are generated. However, the test gives good measures of peak force and area of work during compression indicative of the strength of the gel and product consistency. These forces may also be recorded in reverse on the negative portion of the force-time curve where they are indicative of sample viscosity.

CT3.SETTINGS: MODE: Normal TRIGGER: see table II.2 DISTANCE: 30mm, or appropriate for your container SPEED: 1mm/s

PROBE REF: TA4 38.1mm Ø Perspex Cylinder, or larger if your container allows.

METHOD: Samples were removed from refrigerated conditions of 5°C and centrally positioned beneath the probe within the container in which they were packed. Tests were conducted at ambient conditions of 18.2°C while the test temperature of the low-fat yogurt was 8.7°C and the virtually fat- freewas7.9°C.Itwasessentialthatasufficientdistance(circa20mm)was left between the sample surface and the base of the probe. This was left to ensure that a complete break between probe/sample interface was made during probe retraction so that adhesiveness characteristics could be evaluated.


NOTE: Samples were tested with original containers as supplied. Use of different dimension holding vessels will change results obtained, therefore, operators must be consistent with the test setup used.

. READING:

. .

Peak Positive ForceHARDNESS

Total Negative AreaAdhesiveness (Indication of Viscosity)

t

F

Peak Negative ForceADHESIVE FORCE

Total Positive AreaConsistency

Fat Free

Low Fat

ModulusGradient

(from initialcurve only)

. DISCUSSION: Once the trigger is attained, the force continues to increase until a surface fracture occurs. The modulus changes at this point to a less steep gradient, and the force nearly reaches a plateau.

The low-fat sample appears much softer than the fat-free, having increased flowovertheplungerwithavisuallylessgrainyandmoreglossyfluidappearance. The softer set is characterized by the lower forces and areas of work measured, as well as the shallower slope. The softer set is also characterized by the failure to form sample fracture and the absence of peaks within the curve.

The fat-free sample has a much steeper initial gradient and subsequently higher values for all measured parameters. Its grainy set structure is characterized by the large number of peaks attained within the curve, while the increased viscosity or spoonability is shown within the negative portion of the curve.

. PARAMETER COLLECTION: Peak force and work (area under load curve) will show on CT3 display

when used as stand alone. With an attached computer and TexturePro CT software modulus and many other parameters are available.


PARAMETERS: HARDNESS Force necessary to attain a given deformation

WORK Internal strength of bonds within a product(Total Positive Area)

ADHESIVENESS Work necessary to overcome attractive forces(Total Negative Area) between surface of the food and the materials

with which it comes into contact.

ADHESIVE FORCE Force required to “pull” probe from sample (suction).

MODULUS Ratioofstressdividedbystrainduringthefirstcompression cycle (e.g., the slope of the force:deformation curve). It is representative of sample rigidity.

RESULTS:. LOW-FAT FAT-FREE

MODULUS (g/mm) 7.0 15.7 HARDNESS (g) 122 227 WORK (mJ) 1592.7 3199.9 ADHESION (mJ) -246.4 -522.6 ADHESIVE FORCE (g) -58 -112 BREAK LOAD (g) 122 223

CONCLUSIONS: Creaminess of samples was evaluated as a comparison between low-fat and fat-free samples. This is a comparative measure between two samples, but does give good indication of the effect of formulation on the protein:protein network and resulting gel set. Such a test would be excellent both within the Quality and Development environments, where product matching as well as process control could be facilitated.

The modulus values are also considerably different where the higher valuesforthefat-freefatproductdenotethefirmer,moreboundconsistency of the product.

EMPIRICAL Test conditions which will affect results generated: FACTORS: 1. Sample size 2. Sample age 3. Sample temperature 4. Base and edge effects 5. Sample container and/or test probe employed


Sample conditions which will effect results generated: 1. Fat content 2. Protein content 3. pH 4. Set/Stirred product 5. Syneresis and surface characteristics 6. Presence of inclusions e.g. fruit 7. Temperature and uniformity

. RELATED TESTS: 45° cone penetrometer test utilizing hold until time function to determine relaxation.

BIBLIOGRAPHY AND REFERENCES:

Anon. 1988. Facts About Yogurt. National Dairy Council, London.

Anon.1996.Yogurt:ATechnicalProfile.NationalDairyCouncil,EducationDepartment.

Bylund, G. 1995. Diary Processing Handbook. Tetra Pak Processing Systems AB, Sweden.

Prentice, J. 1992. Dairy Rheology A Concise Guide. VCH Publishers, USA.

Tamime, A. and Robinson R. 1985. Yogurt Science and Technology. Pergamon Press Ltd., Oxford.

Varnam. A. and Sutherland, J. 1994. Milk and Milk Products - Technology, Chemistry and Microbioogy. Chapman and Hall,

Great Britain.

V.� A Comparison of the Textural Characteristics of Biscuits (Cookies)

PRODUCT: Biscuits

OBJECTIVE: To compare the textural characteristics of the two different types of biscuit while utilizing parameters generated using penetration test.

BACKGROUND: The textural characteristics of hygroscopic foods (those which take up water from the atmosphere) such as biscuits is of critical importance in the assessment of their quality. The hardness of a sample is indicative of its freshness, while the crispiness parameter evaluated within this investigation, characterizes its inner crumb structure and bake characteristics.

The test may be employed as part of any quality control procedure, whether that is to evaluate staling of product life, bake characteristics throughquantificationofhardnessatdifferentpointswithinthebiscuitscircumferenceoranyotherapplicationspecifictoyourorganization.

CT3 SETTINGS: MODE: Normal TRIGGER: See table II.1 DISTANCE: 3mm SPEED: 0.5mm/s

PROBE REF: 2 mm stainless steel cylinder probe (REF: TA39)


METHOD: Biscuits approximately 6 mm thick were located beneath the probe and clamped to the analyzer bed using low pressure clips. The probe then penetratedsampletotargetdistanceandtheprofileofcharacteristicswasrecorded through the interface package.

READING:

F Hardness(H1)

Quantity.of.Fractures

Calculate.mean.of.all.values(HAV)

DistanceFracture.Point Final

H1/HAV.=.Indication.of.Crispiness(Crispiness.becomes.a.function.of.hardness)

Relate.the.mean.value.of.peaks.obtained.to.the.original.hardnessvalue...Empirically.our.investigations.highlighted.that.highervalues.of.the.ratio.were.indicative.of.increased.crispiness.

X Y

DISCUSSION: As the probe travels through the sample an initial fracture of the surface is recorded. This fracture is greater in relation to other peaks within the chocolate coated sample due to surface characteristics. A range of internal fractures are then recorded as the probe progresses to the target deformation of 3 mm. The level of peaks within the sample are indicative of crispiness e.g. harder samples showed greater fracture force and were thus considered as being more crispy. The overall force:deformation curve highlights various peaks and troughs as the aerated structure of the sample is penetrated, peaks may be caused through the presence of sugar crystals or where the probe makes contact with air pockets within the dough structure. The overall positive area of the curve is indicative of sample hardness (as is peak force) and may be taken as a direct indication of bake conditions imposed e.g. hotter oven or longer residence time produces a harder biscuit within a sample batch. As two different varieties of biscuit were evaluated, the overall hardness characteristics were considered to be the result of variations in formulation, composition and process conditions imposed. Please note that if inclusions such as chocolate chips or oats are inthebiscuit,theywillcontributedirectlytoresultfluctuations.

PARAMETER COLLECTION: Use with TexturePro CT software is necessary to obtain fracture

calculations.

Brookfield Engineering Labs., Inc. Page 3� Manual No. M/08-37�A0708

PARAMETERS: HARDNESS Load detected at highest peak during compression WORK Integrated area under the compression cycle. Total energy required to penetrate the sample QUANTITY AND NUMBER OF FRACTURES Internal ruptures and fracture of sample as structure is

broken. Indicative of sample brittleness and internal bond strength

CONCLUSIONS: Crispiness is an extremely complex parameter to quantify being a function of many artifact attributes. This investigation has excluded the inclusion of number of peaks in order to simplify the equation employed, however, it should be noted that the number of internal factors is an important considerationwhenevaluatingtheforce:deformationprofilesformed.More comprehensive equations should include the calculation of peaks per mm penetration as well as the internal strength or bake characteristics of the product.

EMPIRICAL Results will be affected by a large number of factors including: FACTORS: 1. Biscuit composition 2. Sample age 3. Atmospheric exposure 4. Positioning beneath probe (closeness to sample edges) 5. Surface characteristics

V.3 Review of Solid Chocolate at Ambient Temperature

PRODUCT: Milk Chocolate (single chunk 27.25mm x 7.92mm)

OBJECTIVE: To determine the optimum penetration distance to detect hardness of solid chocolate tablet through the employment of penetration forces.

BACKGROUND: The CT3 is restricted to maximum force generation in the region of 1kg thus the relatively solid consistency of chocolate determined that a very smallØprobewasutilizedatminimaltestspeed.Thispermittedaflowof molecules within the sample and minimized the forces generated while maximizingtheforce:deformationprofileoftheproduct.

LFRA SETTINGS: MODE: NORMAL TRIGGER: See table II.1 SPEED: 0.1 mm/s DISTANCE: 2, 4, or 6 mm PROBE REF: Stainless steel needle probe, 10° Taper (Ref: TA9)

Confectionery holding rig TA-CJ


METHOD: Samples were removed from wrappers and broken into individual chunks. TheindividualchocolatepiecewasthenheldwithinjawsofconfectioneryholderclampedtoadjustablebedofCT3approximately2mmbelowsurface probe.

. READING:

CONSISTENCYTotal.+ve.Area

HARDNESSPeak.+ve.Force

F

ADHESIONTotal.-ve.Area

ADHESION FORCEPeak.-ve.Force

Note:. Graph.shows.continuation.of.penetration.at.2mm,.4mm. and.6mm.parameter.values.recorded.at.set.points.for. each.penetration.depth.

2mm 4mmD

. .

DISCUSSION: Force: deformation curves generated indicate a linear relationship between forces generated and depth of penetration. It was therefore recommended that the 4mm mid penetration value is utilized to permit evaluation of a range of chocolate types thus enabling comparison of a range of results.

PARAMETER All parameters are automatically calculated within the a test report once COLLECTION they are selected on the test results tab. Thus calculate parameters for

each curve individually and record results.

PARAMETERS: HARDNESS Force necessary to attain a given deformationWORK Internal strength of bonds within a productADHESIVENESS Work necessary to overcome attractive forces

between surface of the food and materials as the probe retracts.

ADHESION Maximum negative load (stickiness)

RESULTS:. PARAMETER UNIT 2mm 4mm 6mm HARDNESS (g) 334 722 1159 WORK (g.mm) 3192.3 1278.6 23878.9 ADHESIVENESS (g.mm) -0.4 -4.1 -180 ADHESION (g) -18 -60 -15.1

where: gs = work NOTE: Adhesion forces give greatest differentiation.


. CONCLUSIONS: This empirical procedure generates key information related to chocolate hardness and consistency, while additional information relating to adhesion is also acquired. Adhesion forces were not considered paramounttotheinvestigationduetodifficultiesinimitatingoralmasticationproperties.Apenetrationdepthof4mm(approx.50%deformationorstrain)wasconsideredoptimumingeneratingkeyprofiledata and is recommended for future investigation using the 1500g CT3 where prevention of upload forces is critical.

EMPIRICAL Test conditions will be affected by: FACTORS: 1. Sample temperature 2. Proximity of test holes within sample 3. Ambient temperatures 4. Base effects where probe compresses against analyzer test bed

Rheologyofchocolateisinfluencedby: 1. Cocoa solids content 2. Cocoa butter content 3. Solid fat content 4. Crystalmodification(actingasanindicationoftemperatureabuse).


Appendix A - Probes, Fixtures, Calibration Accessories and Gelatin Accessories

Thissectionprovidespartnumbersanddetaileddescriptionsforthetestprobesandfixturesthatcanbe used with your CT3 Texture Analyzer. Also included is information on calibration accessories and the equipment used to perform gelatin Bloom tests.

A-� Probes

SELECTED PROBE KITS

TA-P-KIT2 RECOMMENDEDGENERALPROBEKITIncludesthefollowingprobes:60degreeconeTA2/1000;12.7mmcylindrical(BSstd)TA5;60mmwideknifeedgeTA7;1.0mmdianeedleTA9;12.7mmcylindrical(AACCstd)TA10;25.4mmcylindrical(AOACstd)TA11/1000;45degreeconeTA15/1000;30degreeconeTA17;12.7mmballTA18;50.8mmcylinderTA25/1000;0.33mmcuttingwireTA26;2mmrodTA39;38.1mmcylinderTA4/1000;6mmcylindricalTA41;25.4mmballTA43;4mmcylinderTA44 and TA-PCC

TA-P-KIT3 CURDPROBEKIT

Includesthefollowingprobes:5mmdiscTA46;8mmdiscTA-47;10mmdiscTA48 and storage case.

CYLINDER / ROD PROBES * included in TA-P-KIT2 TA3/100 25.4mmDIAMETERCYLINDERPROBE

Clear Acrylic. 35mm Long. Rad .35 - .43mm (Low mass for CT3100) TA3/1000 25.4mmDIAMETERCYLINDERPROBE

Clear Acrylic. 35mm Long. Rad .35 - .43mm. TA4/100 38.1mmDIAMETERCYLINDERPROBE

Clear Acrylic. 20mm Long. Rad .35 - .43mm. (Low mass for CT3100) TA4/1000*38.1mmDIAMETERCYLINDERPROBE

Clear Acrylic 26g. 20mm Long. Rad .35 - .43mm. TA5*12.7mmDIAMETERCYLINDERPROBE

Black Delrin 5g. 35mm Long. Rad .35 - .43mm. TA6 6.35mmDIAMETERCYLINDERPROBE

Black Delrin. 20mm Long. Rad .35 - .43mm. . (Low mass for CT3100)


TA10*12.7mmCYLINDERPROBEClear Acrylic 5g. 35mm length with sharp edge. Gelatin Bloom Probe

TA11/100 25.4mmAOACSTANDARDCYLINDERPROBE

Clear Acrylic. 35mm Long. (Low mass for CT3100) TA11/1000*25.4mmAOACSTANDARDCYLINDERPROBE

Clear Acrylic 21g. 35mm Long. TA19 1cm²KOBETESTPROBE

Stainless Steel. 11.3mm Diameter. 25mm Long. TA24 4mmDIAMETERRODPROBE

Black Delrin. 20mm Long, Flat End TA25/1000*50.8mmDIAMETERCYLINDERPROBE

Clear Acrylic 23g. 20mm Long. Rad .35 - .43mm. TA35 5mmDIAMETERCYLINDERPROBE

Black Delrin. 20mm Long. TA36 7mmDIAMETERCYLINDERPROBE

Stainless Steel. 35mm Long. TA39*2mmDIAMETERRODPROBE

Stainless Steel 5g. 20mm Long. Flat End (Margarine). TA40 4.5mmDIAMETERRODPROBE Stainless Steel. 20.5mm Long. Flat End (Margarine). TA41*6mmDIAMETERCYLINDERPROBE

Stainless Steel 7g. 35mm Long. TA42 3mmDIAMETERCYLINDERPROBE

Stainless Steel. 35.8mm Long. TA44*4mmDIAMETERCYLINDERPROBE

Stainless Steel 10g. TA45 1mmDIAMETERCYLINDERPROBE

Stainless Steel.

CONICAL PROBES * included in TA-P-KIT2 TA2/100 60ºCONEPROBE

Clear Acrylic. 30mm Diameter. (Low mass for CT3100)


TA2/1000* 60ºCONEPROBEClear Acrylic 15g. 30mm Diameter, 36mm L

TA15/100 45ºCONEPROBE

Clear Acrylic. 30mm Diameter. (Low mass for CT3100) TA15/1000* 45ºCONEPROBE

Clear Acrylic 13g. 30mm Diameter, 40mm L TA16 40ºCONEPROBE

Clear Acrylic. 29mm Diameter 41mm L TA17*30ºCONEPROBE

Clear Acrylic 8g. 24mm Diameter, 46mm L TA27 20ºCONEPROBE

Clear Acrylic. 12.4mm Diameter. TA29 15ºCONEPROBE

Stainless Steel. 8mm Diameter. TA32/100 90ºCONEPROBE

Clear Acrylic. 30mm Diameter. (Low mass for CT3100) TA32/1000 90ºCONEPROBE

Clear Acrylic. 30mm Diameter. TA-PCC PROBECARRYINGCASE

For Texture Analyzer Probes And/Or Calibration Weights. (Foam Insert Cut To Order). Black Polypropylene - 225mm(L)X 200mm(W) X 70mm(H).

SPHERICAL PROBES* included in TA-P-KIT2 TA8 6.35mmDIAMETERBALLPROBE

Stainless Steel. TA18*12.7mmBALLPROBE

Stainless Steel 30g TA28 2mmDIAMETERBALLPROBE

Stainless Steel. TA31 1mmDIAMETERBALLPROBE

Stainless Steel. TA33 3mmDIAMETERBALLPROBE

Stainless Steel.


TA38 10mmDIAMETERBALLPROBEStainless Steel.

TA43*25.4mmDIAMETERBALLPROBE

Nylon 14g TA50 5mmDIAMETERBALLPROBE

Surimi application

MISCELLANEOUS PROBES * included in TA-P-KIT2 ** included in TA-P-KIT3

TA-DGA DUALGRIPASSEMBLYThese are multipurpose general grips for tensile type testing. The 25mm wide gripsarefittedwithrubberinsertstomaximisecontactadhesionwithsampleand are capable of holding rectangular samples up to 5mm thick. Each grip clamps from both sides of sample with two opposing thumbscrews for precise alignment. Includes one pair of T-Bolts for mounting to base. Base table kits areNOTUSEDwiththisfixture.

TA7*KNIFEEDGEClear Acrylic 8g. 60mm Wide.

TA9*NEEDLEPROBE

Stainless Steel. 1.0mm Diameter. 43mm Long. 10º Maximum Taper.

TA22 18SWGBARFRAMEPROBE

Aluminium Frame. 39mm Wide.1.2mm Dia TA23 12.7mmDIAMETERROUNDENDPROBE

Black Delrin. 35mm Long. TA26*0.33mmDIAMETERCUTTINGWIREPROBE

Aluminium Frame 67g, 40mm Wide, Connects to M3 Male Thread TA46**TACURDPROBE5mm

Stainless Steel, 5mm dia disc ( 0.2 sq cm ) TA47**TACURDPROBE8mm

Stainless Steel, 8mm dia disc ( 0.5 sq cm ) TA48**TACURDPROBE10mm

Stainless Steel, 10mm dia disc ( 0.8 sq cm ) TA37 2.36mmDIAMETERCUTTINGWIREPROBE

Aluminium Frame. 40mm Wide.


TA49 25.4mmDIAMETERROUNDENDClear Acrylic.

LFRATrain LFRAOn-SiteInstallationandTraining

one day on-site time CT3Train CT3On-SiteInstallationandTraining

one day on-site time TA52 SmallScaleMOHRSShearBlade

Includesonebladeholderandfiveblades.Bladesare9mmWidex35mmLength x .5mm Thick

TA53 .33mm Dia Cutting Wire Probe Aluminum Frame, 40 mm Wide, Connects to M6 Female Thread

A.� Fixtures

ACCESSORIES FOR ROTARY BASE TABLE

TA-RT-KIT ROTARYBASETABLERoundbasetableprovidesquickandeasyheightadjustmenttoaccommodatevarious samples. Accessories listed below are mounted onto this table to facilitate special sample holding requirements. Includes pair of T-bolts for securing table.

ALLACCESSORYFIXTURESBELOWMOUNTONTOROTARYBASETABLE TA-ATT ADHESIVETACKTESTER

Small scale assembly for testing adhesive strength. Requires Rotary Base Table TA-RT-KIT.

TA-AVJ ADJUSTABLEVICEJIG

Small scale assembly for sample positioning. Requires Rotary Base Table TA-RT-KIT.

TA-BEC BACKEXTRUSIONCELL

Small scale back extrusion testing consisting of 3 containers with internal dimensionsof38.1mmdiameter,24mmdeep;includesone25.4mmdiameterprobe. Requires Rotary Base Table TA-RT-KIT.

TA-JTPB JUNIORTHREEPOINTBENDASSEMBLY

Small scale three point bend assembly for fracture test of brittle materials. Probe used with this accy, TA7 Knife Edge Blade, is included in General Probe Kit TA-P-KIT2. Otherwise, please order TA7 separately. Requires Rotary Base Table TA-RT-KIT.


TA-JPA JUNIORPUNCHASSEMBLY

Small scale accessory for controlled puncture testing of solid materials. Probe used with this accy, TA10, is included in General Probe Kit TA-P-KIT2. Otherwise, order TA10 separately. Requires Rotary Base Table TA-RT-KIT.

TA-TBOLTS Pair of T-bolts with nuts and washers.

ACCESSORIES FOR FIXTURE BASE TABLE

TA-BT-KIT FIXTUREBASETABLERectangular base table with removable insert, secured by two screws, which is used as a test surface. With insert removed, all below accessories mount onto this table. Pair of T-bolts for securing table are included.

ALLACCESSORYFIXTURESBELOWMOUNTONTOFIXTUREBASETABLE TA-CJ CONFECTIONERYJIG

Simplesupportjigusedtopermittheaccuratepositioningofirregularshapedsamples beneath the travelling beam. Requires Fixture Base Table TA-BT-KIT

TA-DE DOUGHEXTENSIBILITYJIG

Comprising of 2 aluminium plates - 1 with 25.4mm hole and 1 with 38.1mm holecompletewithupperfixingplatestoholdsample.(ForusewithTA181/2 inch ball probe and TA43 1 inch ball probe respectively). Requires Fixture Base Table TA-BT-KIT

TA-DEC DUALEXTRUSIONCELLFORBOTHBACKANDFORWARD EXTRUSION

Allows back extrusion and forward extrusion. Cylindrical cell 40mm diameter and 50mm in depth. Forces a semi-solid sample through an outlet of known geometry. Complete with 4 plungers of 34mm, 36mm, 38mm and 39.9mm in diameter and interchangeable base plates with apertures of 8mm, 6mm, 4mm, 2mm and one blank. Requires Fixture Base Table TA-BT-KIT

TA-DGA DUALGRIPASSEMBLY

Thesearemultipurposegeneraljigsfortensiletypetesting.Thefixturesutilizeauniversalfittingenabling360ºrotationforcomprehensivetestconfiguration.The25mmwidegripsarefittedwithrubberinsertstomaximisecontactadhesion with sample and are capable of holding rectangular samples up to 5mm thick. Each grip clamps from both sides of sample with two opposing thumbscrews. Attaches to slot in CT3 base. Does not require any base table.

TA-DSJ DOUGHSTICKINESSJIG

Specialsamplefixtureforassessingthestickinessofuncookedbakerydough.May be used with either base table TA-RT-KIT or TA-BT-KIT. TA3/1000 or TA11/1000* Probe.


TA-FMBRA FMBRADOUGHPOTSETStandard accessory used in the preparation of dough samples prior to textural assessment. The set comprises of two test cells and two plungers: An aeration plunger and a compacting plunger. A known weight of sample is placed in the pot and the aeration plunger is used to remove air pockets through gentle rotation.Thedoughisthenassessedforfirmnessusinga6mmindiameterstainless steel probe. Includes Dough Aerator, Dough Compactor & 2 Containers.

TA-JMPA JUNIORMULTIPLEPROBEASSEMBLY

Small scale multiple probe assembly consisting of nine 2mm probes and correspondingbaseplatespecificallydesignedtoholdsmallsamplesofirregular geometry. Requires Fixture Base Table TA-BT-KIT

TA-OC OTTAWACELLThe Ottawa cell follows principles of the Ottawa Test Measurement System (OTMS). An acrylic fronted test cell and corresponding plunger are used to compress and extrude samples. Test samples are extruded by the travelling plunger. Complete With 3 Plates and 2 Plungers for forward and back extrusion. Requires Fixture Base Table TA-BT-KIT

TA-VBJ VOLODKEVITCHBITEJAWS

Compression test used to simulate the shearing action of the front incisors as they bite through a food item, generating an indication of sample toughness orfibrousness.Consistingofbothupperandlowerjaws,thecompressivemovement of the travelling beam imitates the human “biting action”. Requires Fixture Base Table TA-BT-KIT

TA-WSP WIRESHEARPLATE

Aluminium plate with aperture to pass wire cutting blade through for shear type testing. Includes TA 53 cutting wire probe. Requires Fixture Base Table TA-BT-KIT

TA-SB SETOF4SHEARBLADES

IncludingWarnerBratzlertestjigcompletewithslottedbase.Thebladesetincludesfourshearblades,firmlyheldwithinaspeciallydesignedbladeholder.Thejigisutilizedinthemeasurementofshearingandcuttingforces,astheblades pass through a sample. Requires Fixture Base Table TA-BT-KIT

TA-CTP COMPRESSIONTOPPLATERectangular plate 150mm X 100mm, used for compressing large samples. Fixture Base Table TA-BT-KIT is normally used to support sample while testing with this large compression plate.

T-BOLTSTA-RT-5 T-BOLT(2)

TA-RT-3 THUMBNUT(2)


A.3 Calibration Accessories TA-CW-100C CALIBRATIONWEIGHTSET,100gWITHCASE&CERTIFICATE

Set of weights (total mass 100g) to be used to check calibration of the 100g LFRATextureAnalyzer.IncludesverificationcertificatetraceabletoNISTstandards.

TA-CW-1000C CALIBRATIONWEIGHTSET,1000gWITHCASE&CERTIFICATE

Set of weights (total mass 1000g) to be used to check calibration of the 1000g LFRATextureAnalyzer.IncludesverificationcertificatetraceabletoNISTstandards.


Set of weights (total mass 1500g) to be used to check calibration of the 1500g CT3TextureAnalyzer.IncludesverificationcertificatetraceabletoNISTstandards.


Set of weights (total mass 4500g) to be used to check calibration of the 4500g CT3TextureAnalyzer.IncludesverificationcertificatetraceabletoNISTstandards.

TA-CW-10KGCCALIBRATIONWEIGHTSET,10kgWITHCASE&CERTIFICATE

Set of weights (total mass 10kg) to be used to check calibration of the 10kg CT3TextureAnalyzer.IncludesverificationcertificatetraceabletoNISTstandards.

TIA-8013 HANGERMOUNTINGRING

Used to hang calibration weights. Included with each weight set. Replacements may be ordered with this number.

CCSCT3 Calibration&CertificationServiceforCT3

A.4 Gelatin Accessories

TA-GBB-2 BROOKFIELDGELATINBLOOMBOTTLEKIT(12pcs)OnedozenBrookfieldgelatinbloomsamplebottlesw/BELlogobottleholds120ml volume and includes TA-SBS stoppers

GELATINBATHPREPARATIONSYSTEM GelatinPreparationBathSystem


TC-402D(qty2)TC-351D(qty1)

System is used by attaching TC-351 to one TC-402D bath set to 10C. Second TC-402D bath is set to 60C providing rapid transfer between the thermal environments necessary for conditioning gelatin for Bloom testing. Each bath has29Lreservoirandcapacityfortwelve(12)gelatinjarsandaremovablerackforeasyhandling.21Lofwaterisrequiredforproperfluidlevelwithrackand12bloomjars.

TA-SB BROOKFIELDSAMPLEBOTTLES(6pcs)Alternative sample bottle similar to TA-BSB. Order stoppers TA-SBS separately

TA-SBS BROOKFIELDRUBBERSTOPPERS(12pcs)

RubberstoppersforTA-SB(BrookfieldSampleBottles)

CT3-CS-100 BLOOMTESTSTRIPFor use with 100g CT3 Texture Analyzer to check load calibration.

CT3-CS-1000 BLOOMTESTSTRIP

For use with 1000g & 1500g CT3 Texture Analyzer to check load calibration.


Appendix B - Troubleshooting

Ifnopowertotheinstrument:

Check:• User replaceable fuses: two (2) fuses, 4 amp, 5 x 20mm, time-lag located behind removableredcolorpaneljustaboveswitch.

• Fuses located within power entry module on the rear of the instrument.

• If fuses blow continually, serious damage to the instrument could result. Contact repair services immediately.

Probewon’tattach:• Check thread on probe and probe shaft - remove any dirt

RotaryBasetablewon’tmove:• Ensure locking knob is loose

• Ensurefineadjustnutisloose

RotaryBasetablewillnottraveltothelowestposition:• Loosenfineadjustnutandrotatebasetable

• Locate table in center of T-slot

Instrumentisunsteady:• Ensure that bench top is stable

• AdjusttheCT3feet

Probedoesn’tmovewhenstartispressed:• Ensure emergency stop button is not pressed in (rotate clockwise)

• Ensure test mode is not Static Load

• Ensure probe is not in contact with sample (or base table)

Displayshows“REMOTEOPERATION”• This will always show when the computer interface cable is connected to the CT3. To

use the CT3 without the computer program, the serial cable must be disconnected.


Appendix C - Texture Loader Programming

OVERVIEW

Texture Loader software is provided to allow you to create on a PC and download into the CT3 uptotentestmethodsspecifictoyourproduct.YoumaysetupanyCT3test(Normal,HoldTime,Cycle,TPAorTension)withtestparametersspecifictoyourproduct.Yourproductnamemayevenappearasthetestname,subjecttoaneightcharacterlimit.

There are ten memory slots for such programs available in the CT3, labeled 0-9. All memory slots containing tests will appear in sequence as the SELECT/SCROLL knob is rotated. Memory slots can later be hidden by erasing a test using the Erase Test button when its Test No. is selected.

OPERATION OF TEXTURE LOADER

The supplied communication cable, USB or RS232, must be connected to both the CT3 and any valid port on your computer. Turn on the CT3, select StandAlone mode and rotate the SELECT/SCROLL knob to *DOWNLOAD TEST FROM PC

Start TextureLoader software. Be sure to select the correct load cell of your CT3 and choose the correct communications port on your computer. You are now ready to create and load custom programs into your CT3 Texture Analyzer


Userdefinedtestwindow1) Test mode: Choose the type of test you wish to create.

2) Test Number.: Select from the list the number of the memory slot in the CT3 where you wish to load the test.

3) Name: Enter the name of test as you wish it to appear on the screen of the CT3.

TestParameterswindowEnterthedesiredtestparameters.Thespecifictestparametersavailablewillvarydependingupon the test mode chosen.

Now that you have created the test, you may:

1) Save test if desired by clicking on diskette icon button.

2) Click Send Test button to download the test to the CT3.

3) If you decide to change a parameter in a test that has been downloaded to the CT3, you can make the change and download the test to the same memory slot in the CT3. This will overwrite the initial program.


APPENDIX D - CT3 to Computer Command Set

Serial (RS-�3�) Communications Parameters

Baud Rate 115200Data Bits 8Stop Bits 1Parity NoneHandshake None

2

3

4

5

6

7

8

9

1No Connection

Transmit Data (TxD)

Receive

Cable SensingCable Sensing

Serial Ground

No Connection

No Connection

No Connection

Data (RxD)

Pins 4 and 5 are used to sense presence of serial cable.

USB Type B Port Communications Parameters

PIN 1: POWER PIN 3: + Data PIN 2: - Data PIN 4: Cable Gnd


Appendix E- Warranty and Repair Service

BrookfieldTextureAnalyzersareguaranteedforoneyearfromdateofpurchaseagainstdefectsinmaterials and workmanship. The Texture Analyzer must be returned to BrookfieldEngineeringLaboratories,Inc.ortheBrookfielddealerfromwhomitwaspurchasedfornochargewarrantyservice. Transportation is at the purchaser’s expense.

For repair or service in the United States return to:

BrookfieldEngineeringLaboratories,Inc.11 Commerce Boulevard

Middleboro, MA 02346 U.S.A.

Telephone: (508) 946-6200 FAX: (508) 923-5009www.brookfieldengineering.com

ForrepairorserviceoutsidetheUnitedStatesconsultBrookfieldEngineeringLaboratories,Inc.orthedealer from whom you purchased the instrument.

For repair or service in the United Kingdom return to:

BrookfieldViscometersLimited1 Whitehall Estate

Flex Meadow, Pinnacles WestHarlow, Essex CM19 5TJ, United Kingdom

Telephone: (44) 27/945 1774 FAX: (44) 27/945 1775www.brookfield.co.uk

For repair or service in Germany return to:

BrookfieldEngineeringLaboratoriesVertriebsGmbHHauptstrasse 18

D-73547 Lorch, Germany

Telephone: (49) 7172/927100 FAX: (49) 7172/927105www.brookfield-gmbh.de

For repair or service in China return to:

GuangzhouBrookfieldViscometersandTextureInstrumentsServiceCompanyLtd.Room C1, 5/F, Tianxing Building East Tower, No. 21, Zhongshan Yi Road, Yuexiu District

Guangzhou, 510600, P. R. China

Telephone: (86) 20/3760-0548 FAX: (86) 20/3760-0548www.brookfield.com.cn

On-site service at your facility is also available from Brookfield. Please contact our Service Department in the United States, United Kingdom, Germany or China for details.

BROOKFIELD CT3 TEXTURE ANALYZER - Cole-Parmer

Documents

Transcript of BROOKFIELD CT3 TEXTURE ANALYZER - Cole-Parmer