Bridge Bearings. Use of BS 5400: Part 9: 1983"Bearing Schedule. The bearing design requirements and...
Transcript of Bridge Bearings. Use of BS 5400: Part 9: 1983"Bearing Schedule. The bearing design requirements and...
Bridge Bearings. Use of BS 5400: Part 9: 1983
DN-STR-03004 December 2000
Design Standards DN
TRANSPORT INFRASTRUCTURE IRELAND (TII) PUBLICATIONS
About TII Transport Infrastructure Ireland (TII) is responsible for managing and improving the country’s national road and light rail networks. About TII Publications TII maintains an online suite of technical publications, which is managed through the TII Publications website. The contents of TII Publications is clearly split into ‘Standards’ and ‘Technical’ documentation. All documentation for implementation on TII schemes is collectively referred to as TII Publications (Standards), and all other documentation within the system is collectively referred to as TII Publications (Technical). This system replaces the NRA Design Manual for Roads and Bridges (NRA DMRB) and the NRA Manual of Contract Documents for Road Works (NRA MCDRW). Document Attributes Each document within TII Publications has a range of attributes associated with it, which allows for efficient access and retrieval of the document from the website. These attributes are also contained on the inside cover of each current document, for reference. For migration of documents from the NRA and RPA to the new system, each current document was assigned with new outer front and rear covers. Apart from the covers, and inside cover pages, the documents contain the same information as previously within the NRA or RPA systems, including historical references such as those contained within NRA DMRB and NRA MCDRW. Document Attributes
TII Publication Title Bridge Bearings. Use of BS 5400: Part 9: 1983 TII Publication Number
DN-STR-03004
Activity Design (DN) Document Set Standards
Stream Structures (STR) Publication Date December 2000
Document Number
03004 Historical Reference
BD 20
NRA DMRB and MCDRW References For all documents that existed within the NRA DMRB or the NRA MCDRW prior to the launch of TII Publications, the NRA document reference used previously is listed above under ‘historical reference’. The TII Publication Number also shown above now supersedes this historical reference. All historical references within this document are deemed to be replaced by the TII Publication Number. For the equivalent TII Publication Number for all other historical references contained within this document, please refer to the TII Publications website.
National Roads Authority Volume 2 Section 3 Design Manual for Roads and Bridges Part 1 BD 20/92 Addendum
December 2000 1
NRA ADDENDUM TO
BD 20/92
BRIDGE BEARINGS USE OF BS 5400: PART 9: 1983
Standard BD 20/92 - Bridge Bearings, Use of BS 5400: Part 9: 1983 - is applicable in Ireland with the
following amendments:
GENERAL
1. The Standard provides specification requirements for use in public purchasing contracts. It does not
lay down legislation requirements for products and materials used in road construction in Ireland.
2. At several locations:
For: “Specification for Highway Works (December 1991) (MCHW 1)”
Read: “NRA Specification for Road Works”;
For: “highway”
Read: “road”;
For: “Overseeing Department”
Read: “National Roads Authority”.
National Roads Authority Volume 2 Section 3 Design Manual for Roads and Bridges Part 1 BD 20/92 Addendum
December 2000 2
SPECIFIC
1. Page 1/1, Paragraph 1.3:
Delete text and replace with:
“1.3 This Standard should be used forthwith for
all schemes for the construction and/or
improvement of national roads. The Standard
should be applied to the design of schemes already
being prepared unless, in the opinion of the
National Roads Authority, application would result
in significant additional expense or delay progress.
In such cases, Design Organisations should
confirm the application of this Standard to
particular schemes with the National Roads
Authority.”
2. Page 3/1, Paragraph 3.1, line 4:
For: “Notes for Guidance on Specification for Highway Works (December 1991)(MCHW 2).”
Read: “NRA Notes for Guidance on the Specification for Road Works.”
3. Page 4/1, Paragraph 4.2:
Delete Paragraph 4.2 and replace with:
“4.2 NRA Manual of Contract Documents for Road Works:
Volume 1: Specification for Road Works
Volume 2: Notes for Guidance on the Specification for Road Works”.
4. Page 5/1, Section 5:
Delete text and replace with:
“5.1 All technical enquiries or comments on this Standard should be sent in writing to:
Head of Project Management and Engineering
National Roads Authority
St Martin’s House
Waterloo Road
Dublin 4”
……………………………………………
E O’CONNOR
Head of Project Management and
Engineering
Bridge Bearings
Use of BS 5400: Part 9:1983
Summary: This Standard gives the requirements for the design of bridge bearings usingBS 5400: Part 9: 1983
THE HIGHWAYS AGENCY BD 20/92
THE SCOTTISH OFFICE DEVELOPMENT DEPARTMENT
THE WELSH OFFICEY SWYDDFA GYMREIG
THE DEPARTMENT OF THE ENVIRONMENTFOR NORTHERN IRELAND
Volume 2 Section 3Part 1 BD 20/92 Registration of Amendments
ELECTRONIC COPY - NOT FOR USE OUTSIDE THE AGENCY
October 1992 PAPER COPIES OF THIS ELECTRONIC DOCUMENT ARE UNCONTROLLED
REGISTRATION OF AMENDMENTS
Amend Page No Signature & Date of Amend Page No Signature & Date ofNo incorporation of No incorporation of
amendments amendments
Volume 2 Section 3Registration of Amendments Part 1 BD 20/92
ELECTRONIC COPY - NOT FOR USE OUTSIDE THE AGENCY
PAPER COPIES OF THIS ELECTRONIC DOCUMENT ARE UNCONTROLLED October 1992
REGISTRATION OF AMENDMENTS
Amend Page No Signature & Date of Amend Page No Signature & Date ofNo incorporation of No incorporation of
amendments amendments
DESIGN MANUAL FOR ROADS AND BRIDGES
ELECTRONIC COPY - NOT FOR USE OUTSIDE THE AGENCY
October 1992 PAPER COPIES OF THIS ELECTRONIC DOCUMENT ARE UNCONTROLLED
VOLUME 2 HIGHWAYSTRUCTURES:DESIGN(SUBSTRUCTURESAND SPECIALSTRUCTURES),MATERIALS
SECTION 3 MATERIALS ANDCOMPONENTS
PART 1
BD 20/92
BRIDGE BEARINGS USE OF BS 5400:PART 9: 1983
Contents
Chapter
1. Introduction
2. Use of the British Standard
3. Additional Requirements
4. References
5. Enquiries
Annex A Amendments to BS 5400: Section 9.1:1983
Volume 2 Section 3 Chapter 1Part 1 BD 20/92 Introduction
ELECTRONIC COPY - NOT FOR USE OUTSIDE THE AGENCY
October 1992 PAPER COPIES OF THIS ELECTRONIC DOCUMENT ARE UNCONTROLLED 1/1
1. INTRODUCTION
1.1 This Standard updates and replaces BD 20/83:Bridge Bearings - Use of BS 5400: Part 9: 1983. Themajor changes in this revision are as follows:-
i. All references relating to the specificationclauses in BS 5400: Part 9: Section 9.2: 1983,are withdrawn. Specification clauses given inthe Specification for Highway Works(December 1991) (MCHW 1) shall be used.
ii. In clause 10.6 of BS 5400: Section 9.1: 1983the equation for ," is modified.
Scope
1.2 This standard covers the use of BS 5400: Part9: Section 9.1: 1983 for the design of bearings inhighway bridges.
Implementation
1.3 This Standard should be used forthwith on allschemes for the construction, improvement andmaintenance of trunk roads, including motorways,currently being prepared provided that, in the opinion ofthe Overseeing Department, this would not result insignificant additional expense or delay progress. Design Organisations should confirm its application toparticular schemes with the Overseeing Department.
Volume 2 Section 3 Chapter 2Part 1 BD 20/92 Use of the British Standard
ELECTRONIC COPY - NOT FOR USE OUTSIDE THE AGENCY
October 1992 PAPER COPIES OF THIS ELECTRONIC DOCUMENT ARE UNCONTROLLED 2/1
2. USE OF THE BRITISH STANDARD
2.1 The design of bearings for the OverseeingDepartment's highway bridges shall be carried out inaccordance with BS 5400: Section 9.1 as amended bythis Standard. The amendments to Section 9.1 are givenin Appendix A to this standard.
2.2 The British Standard BS 5400: Section 9.1 asamended by this Standard supersedes the following:
i. Technical Memorandum (Bridges) No BE1/76; Design Requirements for ElastomericBridge Bearings.
ii. Interim Memorandum (Bridges) No IM 11;PTFE in Bridge Bearings.
2.3 Where reference is made to any Part of BS5400, this shall be taken as a reference to that Part asimplemented by the Overseeing Department.
Volume 2 Section 3 Chapter 3Part 1 BD 20/92 Additional Requirements
ELECTRONIC COPY - NOT FOR USE OUTSIDE THE AGENCY
October 1992 PAPER COPIES OF THIS ELECTRONIC DOCUMENT ARE UNCONTROLLED 3/1
3. ADDITIONAL REQUIREMENTS
3.1 Specification clauses for bearings for use in theOverseeing Department's highway bridges are given inthe Specification for Highway Works (December 1991)(MCHW 1). Advice on these is contained in the Notesfor Guidance on the Specification for Highway Works(December 1991)(MCHW 2).
3.2 The clauses in BS 5400: Section 9.1 areexpressed in the form of recommendation generallyusing the word "should"; however these shall beconsidered as mandatory for the purpose of thisStandard.
3.3 Proprietary bearings, and structuralcomponents of bearings (eg in aluminium alloy), whichfall outside the scope of BS 5400: Part 9, are notcovered by this Standard.
3.4 Where bridge bearings are procured through acontract incorporating the Specification for HighwayWorks (December 1991) (MCHW 1) productsconforming to equivalent standards or specifications ofother member states of the European Community willbe acceptable in accordance with the terms of the 104and 105 Series of Clauses of that Specification. Anycontract not containing these Clauses must contain asuitable clause of mutual recognition having the sameeffect regarding which advice should be sought.
Volume 2 Section 3 Chapter 4Part 1 BD 20/92 References
ELECTRONIC COPY - NOT FOR USE OUTSIDE THE AGENCY
October 1992 PAPER COPIES OF THIS ELECTRONIC DOCUMENT ARE UNCONTROLLED 4/1
4. REFERENCES
4.1 BS 5400: Steel, Concrete and CompositeBridges Part 9: Bridge bearings. Section 9.1:1983, Code of Practice for design of bridgebearings.
4.2 Manual of Contract Documents for HighwayWorks:-
Volume 1: Specification for Highway Works(December 1991): HMSO (MCHW 1).
Volume 2: Notes for Guidance on theSpecification for Highway Works(December 1991): HMSO (MCHW 2).
Volume 2 Section 3 Chapter 5Part 1 BD 20/92 Enquiries
ELECTRONIC COPY - NOT FOR USE OUTSIDE THE AGENCY
October 1992 PAPER COPIES OF THIS ELECTRONIC DOCUMENT ARE UNCONTROLLED 5/1
5. ENQUIRIES
All technical enquiries or comments on this Standard should be sent in writing as appropriate to:-
Chief Highway Engineer The Department of Transport St Christopher House Southwark Street T A ROCHESTER London SE1 OTE Chief Highway Engineer
The Deputy Chief Engineer Roads Directorate The Scottish Office Industry Department New St. Andrew's House J INNES Edinburgh EH1 3TG Deputy Chief Engineer
The Director of Highways Welsh Office Y Swyddfa Gymreig Government Buildings Ty Glas Road Llanishen K J THOMAS Cardiff CF4 5PL Director of Highways
Chief Engineer Dept. of the Environment for Northern Ireland Commonwealth House Castle Street W J McCOUBREY Belfast BT1 1GU Chief Engineer - Roads Service
Orders for further copies should be addressed to:-
DOE/DOT Publications Sales Unit Government Building Block 3, Spur 2 Lime Grove Eastcote HA4 8SE Telephone No: 081 - 429 5170
Volume 2 Section 3Part 1 BD 20/92 Annex A
ELECTRONIC COPY - NOT FOR USE OUTSIDE THE AGENCY
October 1992 PAPER COPIES OF THIS ELECTRONIC DOCUMENT ARE UNCONTROLLED A/1
AMENDMENTS TO BS 5400: SECTION 9.1: 1983
Page 4
5.6 Add the following at the end of clause:-
"For bearings in halving joints access for inspection and replacement is practically impossible for slab typebridges and extremely difficult for beam and slab construction."
Page 7
5.17 Delete clause and insert the following
"Bearing Schedule. The bearing design requirements and acceptance tests shall be listed in a bearing schedule. A typical bearing schedule for this purpose is set out in Appendix A of Section 9.1."
Page 10
10.1.1 After the last sentence, insert additional sentence as follows:-
"The use of pad and strip bearings shall be restricted to small and simply supported structures of spans less than10 metres."
Page 11
10.6 Delete the equation for ," and insert the following:
" ," = (b "b + l "l) te e i2 2
))))))))))))))) 2 G(t )i
3
The outer protective layers shall be ignored in the calculation of ,"." Page 12
10.6 Delete definition for Gt .i
10.11 Delete `Numerically, H < 0.1 (V+ 2A )'; and insert1
"H is less than each of the following:-
i. 0.1 (V + 2A )1
ii. 0.2V"
Volume 2 Section 3Annex A Part 1 BD 20/92
ELECTRONIC COPY - NOT FOR USE OUTSIDE THE AGENCY
PAPER COPIES OF THIS ELECTRONIC DOCUMENT ARE UNCONTROLLED October 1992A/2
Page 15
Table 9 Extend the typical bridge bearing schedule by adding the following items and additional footnote at thebottom:-
Number ofcompletebearings to besubjected toacceptancetesting
Bearings other horizontal load** testthan elastomeric at serviceability limitbearings state
Combined vertical and
Combined vertical andhorizontal load** testat ultimate limit state
Laminated Quick production testelastomericbearings
Compressive stiffnesstest
Shear stiffness test
** Load values for testing shall be derived from the design load effects above multiplied by the appropriatevalue of partial material factor ( .m
Ionad Ghnó Gheata na
Páirce,
Stráid Gheata na Páirce, Baile Átha Cliath 8, Éire
www.tii.ie
+353 (01) 646 3600
Parkgate Business Centre,
Parkgate Street,
Dublin 8, Ireland
+353 (01) 646 3601