BRC Catalogue

2007

the essential guide to reinforcing concrete

Bar & fabric products

Spacers & accessories

Slab products

Formwork

Weldmesh and gabions

We reserve the right to substitute any product described in this catalogue with a similar product of the same or better qualitywithout prior notice. Similarly, products supplied may differ from the profiles illustrated, but will offer the same functionality.

Please note: drawings are for reference only and are not to scale. Usage information, where offered, is for guidance only.

Errors and omissions excepted. March 2006.

Bar & fabricproducts

p5-15

Spacers &accessories

p16-19

Slab products

p20-26

Formwork

p27-29

Weldmesh & gabions

p30-31

the essential guide to reinforcing concrete

Midlands 01623 555111North 01226 730330North East 01325 381166

North West 0161 620 1001South 01794 521158South East 020 7474 1800

South West 01752 894660Scotland 01698 732343Wales & West 01633 244002

Sales offices:

� Quality Managementsystems to BS EN ISO 9001:2000

� National coverage

� CARES approvedat all locations

� After sales support

� Dedicated contractmanagement

� Technical support

� Capacity to handleall sizes of project

� Competitive pricing

� Commitment to total customer service

Customer service, quality systems, technical support, competitive prices

BRC is the UK’s largest supplier of steel reinforcementand associated products for concrete. With a networkof strategically placed manufacturing locations, we areable to meet all your requirements regardless of thesize of project.

We have tried to make this catalogue as comprehensive aspossible, but cannot include every single item from our hugeproduct range. So, if you do not see the product you are looking

for, please give us a call. Youwill find contact numbers for

all our sales offices at thebottom of every page.

ContractmanagementA nationwide networkof dedicated,professional teamsmonitor the flow of informationfrom site call-off,through manufacturingto point of delivery, toensure that yourrequirements are

fully met.

850303





Sales offices:5

� High yield reinforcing bar to BS4449:2005 in diameters 8mm to 40mm*.� 6mm and 50mm are non-preferred sizes available to special order.� Strategically placed manufacturing and distribution locations throughout the UK.� All cut and bent reinforcement conforms to the relevant British Standard.

* BS4449:2005 does not cover mild steel

Cut and bent reinforcement

BRC offer a prefabricated solution tailored to suit individual needs. Whether it is to speed construction or solve skill shortages, BRCcan provide the answer. By recognising that the skill level on sites will vary, BRC are able to offer a solution that can be easily applied.

BARWELD®

� A range ofsolutions areavailable to suitsite skill levels.

� Can be suppliedin packages forease of planning.

Housing� Heavy duty

solutions.

� A range of splicedetails areavailable.

� Beam sizes can bedetailed to suitlifting equipment.

Industrial and piled foundations

� Single piece units for speed of placing.

� Larger units canbe supplied insections.

� Pile cages arealso available.

Bases and pile caps� Heavy bars

can be convertedto mats for fasterconstructioncycles.

� Sheet sizes canbe detailed tosuit specificapplications.

Bar mats

Prefabricated reinforcement

The pressures of today’s construction industry continue to requireinnovative solutions. Skill shortages, confined sites and thedemands for faster construction, all need clear thinking.

BRC have accumulated a wealth of experience in this field, and can support you through all stages from design to construction. Our engineering teams will work with you to identify a solution that meets your needs.

For projects ranging from a house extension to a high-rise apartment scheme, we can offer an extensive package utilising those products and services that will give you the best result.

Reinforcement solutions

To explore the opportunity to save time and money, please contact your local BRC sales office

850303





Sales offices:6

Reinforcement shape codes to BS8666:2005

A

B

A

(C)

(C)

A

BD

A

B

(C)

D

A

C

D

B (E)

(D)

B

(C)

A

A

R

C

B

A

A

B

(C)

(E)

A

C D

B

C

A

(D)

B

E

B

A

(D)

C

A

(C)

(D)

B

A

(B

B is the overlap

)

(B)

A

A

B

(C)

A

B

(C)

D

A

C

(D)

B

C

DB

(E)

A

C

(E)

B

(F)

A

D

A

B

C = number of turns

(B)

AR

B

CA

(D)

Semi-circular

A

D

B

(C)

(C)

A

Semicircular B

A

C

BD

(E)

A

(D)(C)

B

A

Isometric sketch

B

C

(D)

B

A

Semi-circular

(C)

B

A

B

(C)

B

A(C)

D

C

(E)B

A

D

A

D DB B

C

(E)

A

BD

C(F)

E

SHAPE CODE 00 SHAPE CODE 01 SHAPE CODE 11 SHAPE CODE 12 SHAPE CODE 13






SHAPE CODE 67 SHAPE CODE 75 SHAPE CODE 77 SHAPE CODE 98

All other shapes areShape Code 99 andrequire fully dimensionedsketches.

L=A L=A L=A + (B) – 0.5r – d L=A + (B) – 0.43R – 1.2d L=A + 0.57B + (C) – 1.6d

L=A + (C) - 4d

L=A + B + (C) – r – 2d L=A + B + C + (D) – 1.5r – 3d L=A + B + C + (D) – 1.5r – 3d L=2A + 1.7B + 2(C) – 4d L=A + B + C + (E) – 0.5r – d

L=A + 2B + C + (E)L=A + B + C + D + (E) – 2r – 4dL=A + B + C + D + (E) – 2r – 4dL=A + B + C + (D) – r – 2dL=A + B + C + (E) – 0.5r – d

L=2A + B + 2(C) + 1.5r – 3d L=2(A + B + (C)) – 2.5r – 5d L=A + B + C + D + 2(E) - 2.5r - 5d L=2A + 3B + 2(C) – 3r – 6d L=A+B+C+2D+E + (F) – 3r – 6d

850303

L=A + 2B + C + (D) – 2r – 4dL=Cπ(A – d)L=π (A–d) + BL=A

L=A + B + (C) – r – 2dL=A + B + C + (D) – 1.5r – 3dL=A + B + (C) – r – 2dL=A + (C)

L=A + B + (C) L=A + B + (E) L=A + B + (C) L=A + B + (C) – 0.5r – d L=A + B + (C) – 0.5r – d

Stock lengths

Nominal Minimum radius Minimum diameter Minimum end projection (P)size for scheduling for bending former General Links where

(min. 5d straight) bend <150°(min.10d straight)

6 12 24 110 1108 16 32 115 115

10 20 40 120 13012 24 48 125 16016 32 64 130 21020 70 140 190 29025 87 175 240 36532 112 224 305 46540 140 280 380 58050 175 350 475 725(B)

P5d

Table of minimum dimensions

*6mm and 50mm are non-preferred sizes available to special order

*

*





Sales offices:7

Sectional area (mm2) of bars per metre width for various c/c (mm)

C/C (mm) 6* 8 10 12 16 20 25 32 40 50*

75 377 671 1050 1510 2680 4190 6550 10700 ——- ——-100 283 503 785 1130 2010 3140 4910 8040 12600 ——-125 226 402 628 905 1610 2510 3930 6430 10100 15700150 189 335 523 754 1340 2090 3270 5360 8380 13100175 162 287 449 646 1150 1800 2810 4600 7180 11200200 142 252 393 566 1010 1570 2450 4020 6280 9820250 113 201 314 452 804 1260 1960 3220 5030 7850300 94.3 168 262 377 670 1050 1640 2680 4190 6540350 80.9 144 224 323 575 898 1400 2300 3590 5610400 70.8 126 196 283 503 786 1230 2010 3140 4910450 62.9 112 174 251 447 698 1090 1790 2790 4360500 56.6 101 157 226 402 628 982 1610 2510 3930


Properties of high yield bars

Size (mm) 6* 8 10 12 16 20 25 32 40 50*

Dims (max O/A mm) 7 10 12 14 19 23 29 37 46 58

Mass (kg per m) 0.222 0.395 0.616 0.888 1.579 2.466 3.854 6.313 9.864 15.413

Metres per tonne 4504 2531 1623 1126 633 405 259 158 101 64


Radius of bendingReinforcement to be formed to a radius exceeding that specified in the table below shall be supplied straight. The required curvaturemay be obtained during placing. For shapes with straight and curved lengths (e.g. shape codes 13 and 33) the largest practical radiusfor the production of a continuous curve is 200mm, and for larger radii the curve may be produced by a series of short straightsections.

Bar size (mm) 6* 8 10 12 16 20 25 32 40 50*Radius (m) 2.50 2.75 3.50 4.25 7.50 14.00 30.00 43.00 58.00 75.00

Tolerances on cutting & bending dimensionsThe tolerances for cutting and/or bending dimensions shall be inaccordance with the table to the right and shall be taken intoaccount when completing the schedule. The end anchorage or thedimension in parentheses in the shape codes specified in the tableopposite shall be used to allow for any permissible deviationsresulting from cutting and bending.

Cutting & bending tolerances Tolerance (mm)Cutting of straight lengths (incl. reinforcement for subsequent bending) +25 -25Bending ≤ 1000mm +5 - 5

> 1000mm to ≤2000mm +5 -10> 2000mm +5 -25

Reinforcing bar technical dataWeight per m2 in one direction (add both directions for total m2 weight)

BAR SIZE SPACING OF BARS (mm)(mm) 75 100 125 150 175 200 225 250 275 300

6 2.959 2.220 1.776 1.480 1.268 1.110 0.986 0.888 0.807 0.7408 5.261 3.946 3.157 2.631 2.255 1.973 1.754 1.578 1.435 1.315

10 8.220 6.165 4.932 4.110 3.523 3.083 2.740 2.466 2.242 2.05512 11.838 8.878 7.103 5.919 5.073 4.439 3.946 3.551 3.228 2.95916 21.044 15.783 12.627 10.522 9.019 7.892 7.015 6.313 5.739 5.26120 32.882 24.661 19.729 16.441 14.092 12.331 10.961 9.865 8.968 8.22025 51.378 38.534 30.827 25.689 22.019 19.267 17.126 15.413 14.012 12.84532 84.178 63.133 50.507 42.089 36.076 31.567 28.059 25.253 22.958 21.04440 131.528 98.646 78.917 65.764 56.369 49.323 43.843 39.458 35.871 32.88250 205.512 154.134 123.307 102.756 88.077 77.067 68.504 61.654 56.049 51.378



*

*


Electrically welded fabric to BS4483:2005

All standard sheets (A, B, C and D) are 4.8 x 2.4m.A142, A193, A252, A393 and B785 are also availablein merchant size sheets 3.6 x 2.0m.

See below for Flying End® range.

BS8666:2005 FABRIC MESH SIZE NOMINAL DIAMETER OF WIRE CROSS SECTION AREA NOMINAL MASS NO. OF SHEETS

BRC REF. PITCH OF WIRES PER METRE WIDTH PER m2 PER TONNE

Main Cross Main Cross Main Crossmm mm mm mm mm2 mm2 kg

Square meshA393 200 200 10 10 393 393 6.16 15A252 200 200 8 8 252 252 3.95 22A193 200 200 7 7 193 193 3.02 29A142 200 200 6 6 142 142 2.22 40Structural meshB1131 100 200 12 8 1131 252 10.90 8B785 100 200 10 8 785 252 8.14 11B503 100 200 8 8 503 252 5.93 15B385 100 200 7 7 385 193 4.53 20B283 100 200 6 7 283 193 3.73 24Long meshC785 100 400 10 6 785 70.8 6.72 13C636 100 400 9 6 636 70.8 5.55 16C503 100 400 8 6 503 70.8 4.51 21C385 100 400 7 6 385 70.8 3.58 26C283 100 400 6 6 283 70.8 2.78 34Wrapping meshD98 200 200 5 5 98 98 1.54 57D49 100 100 2.5 2.5 49 49 0.77 113

Standard fabric




Sales offices:

8

BRC Flying End® fabrics are stocked in manyBritish Standard references, offering considerablebenefits over traditional fabric sheets:

� Accurate cover – extended overhangs caneliminate wire build-up at laps.

� Faster laying cycle – simplified lap detailsimproves speed of laying and assists checking.

� Reduced wastage – in certain cases, largersheet sizes can reduce on-site cutting andwaste.

� Increased flexibility – reducing the lap build-upallows improved flexibility when positioningBRC circular spacers.

� Reduced quantity – the larger sized sheets andthe use of deformed wire can reduce laplengths and overall quantity of fabric.

B.S. FABRIC SHEET MAIN CROSSREF. SIZE WIRE WIRE

(m) O/H (mm) O/H (mm)A Types 5.9 x 2.3 100/400 100/400A Types 4.8 x 2.4 100/500 100/500B Types 4.8 x 2.4 100/500 50/350

The standard Flying End® fabric range comprises:

930102

Standard Flying End® fabric


9

BRC made-to-measure fabric reinforcementBRC can manufacture standard A, B & C types in sizes to suit your application(subject to machine capability, transport and handling on site). With or withoutFlying Ends®, a more cost effective solution can be achieved by reducing cutting,wastage and lapping congestion.

BRC tailored fabric reinforcementDesigned to suit specific projects, BRC can provide mesh that offers an alternativeto conventional loose rebar. Supplied with or without Flying Ends®, reinforcement invarious diameters can be offered in sheet sizes to suit your contract (subject tomachine capability, transport and handling on site).

A cost-effective alternative to loose rebar inheavily reinforced areas.

Standard, Flying End® and made-to-measurefabrics can be supplied cut to size or bent.

Most British Standard shape codes can beaccommodated but it may be necessary tomanufacture them in sections for ease oftransportation or to enable the shape to becompleted.

OL1,OL2 Overhangs of longitudinal wires OL3, OL4 Overhangs of cross wiresLL Length of longitudinal wires (not necessarily the longest wires in the sheet) LC Length of cross wiresPL Pitch of longitudinal wiresPC Pitch of cross wires

930102

Made-to-measure and tailored fabric reinforcement

One directional fabric

Cut and bent fabric




Sales offices:





Sales offices:10

Ancon Reinforcing Bar Couplers - strong, fast and easy to use

Standard Series - Connects rebars of the same diameter

Positional Series-For use where the continuation bar cannot be rotated

Transition Series - Connects rebars of different diameters

� Suitable for the majority of rebar joining applications� Fast and simple to install� Tested and approved by UK CARES to show compliance

with BS8110� Full destructive tests carried out to demonstrate

compliance with BNFL Specification E45 andBNF.ES.0039_I_B Category B

Bar Diameter 12 16 20 25 32 40 50Standard Series � � � � � � �Positional Series � � � � � � �Transition Series � � � � � � �

� No bar end preparation required� Installation requires no specialist equipment� No bar rotation required� The ET Series is the only BBA approved

rebar coupler� Suitable for use on imperial, plain round

or deformed bar� Ideal for remedial applications where replacement

of damaged or corroded baris necessary

Bar Diameter 10 12 16 20 25 32 40 50ET Series � � � � � � � �Continuity Series � � � � � �Transition Series � � � � � � �Headed Anchor � � � � � � � �

Bar Diameter 12 16 20 25 28 32 36 40 50Type A � � � � � � � � �Type B � � � � � � � � �Type C � � � � � � � � �

ET Series - Connects rebars of the same diameter

Transition Series - Connects rebars of different diameters

Headed Anchor - Provides dead end embedment for bars in concrete

Continuity Series - For use in phased construction

� Quick and easy to install� Designed for use on large scale, high coupler volume projects� Tested to demonstrate compliance with BNFL Specification E45 and

BNF.ES.0039_I_B Category A and BS8110, providing a full strength barbreak connection.

Type A - Used where the continuation bar can be rotated

Type C - Used where the continuation bar cannot be rotated

Type B - Used where it is difficult but not impossible to rotate thecontinuation bar

w w w. a n c o n . c o . u k

Tapered thread range

MBT range

Bartec range

TAPERED THREAD RANGEGROUP CBB32

MBT RANGEGROUP CBB30

BARTEC RANGEGROUP CBB12





Sales offices:11

The Ancon Eazistrip Reinforcement Continuity System is a quick and easy to install method of maintaining continuity ofreinforcement at construction joints in concrete. It consists of a galvanised steel casing with a dimpled surface toprovide an effective concrete bond. Pre-bent bars are housed within the casing and are enclosed by a protectivecover. Each end of the unit is sealed with a polystyrene block in order to prevent the ingress of concrete.

The unit is nailed to the formwork and the concrete is cast. After striking the formwork, the cover is

removed and the bars straightened, ready for lapping onto the main reinforcement.

Benefits� Accelerates the construction process� Simplifies formwork design � Removes the need to drill shuttering� Casing protects bars until required� Risk of site injuries from projecting bars

is minimised� Easy to install by site operatives

Ancon Eazistrip - Reinforcement Continuity System

Type H Hook(standard in 60mm and 80mm box)

h l

Type 2H Double Hook(not available in 60mm & 80mm box)

h l

Radiused Eazistrip is available.Please contact Ancon or BRCwith your requirements.

Where the potential for water ingress throughthe construction joint is a major concern,Eazistrip can be supplied with a Pentaflexhydrostatic seal.

b

Type RU U Bar

h l

b

Type U U Bar Type S Straight Bar

h l h l

Type S2 Double Straight Bar

h l

b b

Type SH Angle with legin horizontal plane

h l

b

Type RA Angle

h l

b

Type RA1 Double Angle

h l

bb


h l

b

b

c c


h l

b

b

c

w w w. a n c o n . c o . u k

Eazistrip Reinforcement Continuity Systems are manufactured using CARESapproved bar which meets the requirements of BS4449.

Ancon Eazistrip

Radiused Eazistrip Eazistrip Water Stop

ANCON EAZISTRIP GROUP CEE40

Applications� Floor slabs� Walls � Stairwells� Corbels� Diaphragm walls� Jumpforms� Brick support ledges

A

D

Max. Fo

B Fc

Max. Fo

B

D

Fc

A

P13

P14




Sales offices:12


Reinforcing Bar Couplers

LENTON® Taper Threaded Couplers

■ LENTON® Couplers hold CARES Approval TA1C 5003 on compliance for BS 8110: Part 1: 1997 andthe BNFL Specification for Couplers for use in tension under static loading conditions in sizes 12-50 mm.

■ LENTON® PLUS BAR BREAK on A12, P13/P14 holds CARES approval TA1C5009 complying withBS 8110 Part 1 1997 and BNFL Specification for couplers for Type A mechanical splices.

LENTON® Standard Coupler A12

■ LENTON® A12 Couplers splice the same diameter bars where one bar can be rotated.

LENTON® Position Couplers P13/P14

■ LENTON® P13 Position Couplers splice bars where the ongoing bar is restricted in its axialmovement or cannot be rotated and length adjustability of the coupler is required.

■ LENTON® P14 Position Couplers splice bars which cannot be rotated such as bent bars or hooks.

LENTON® POSITION COUPLERS P13/P14

GROUP CBB86

Rebar size 10 12 16 20 25 32 40 50DesignationMetric (mm)A 22* 22* 27* 33 41 52 64 80

B-P13 74 77 88 112 127 144 179 214

B-P14 42 45 54 75 83 95 114 140

Fc-P13 42 42 48 63 68 79 91 111

Fc-P14 42 42 48 63 68 79 103 111

Max Fo-P13 85 85 93 116 128 144 172 204

MaxFo-P14 53 53 59 79 84 95 131 130

D 18 18 24 36 41 46 58 71

*Use hex material (measured across the flats), others

use round material.

LENTON® STANDARD COUPLER A12

GROUP CBB75

Rebar size 10 12 16 20 25 32 40 50DesignationMetric (mm)A 17* 17* 22* 27* 33 42 52 64

B 48 49 61 88 96 107 131 163

D 18 18 24 36 41 46 58 71

Design benefits

• Allows maximum

bar cross-section to

be used

• Small diameter

reduces the need

for concrete cover

and eliminates

rebar congestion

• Short length and

slim design helps

ensure the least

disturbance to

uniform stiffness

• Splice strength is

independent of

rebar deformation

• Unique tapered

thread requires no

lock nuts and

provides a positive

locking, no-slip

connection

• Any length, shape,

diameter or

combination of bar

sizes can be

mechanically

spliced

www.erico.com

D

B

A

• LENTON®

R11 Transition Couplers are also available.

*Use hex material (measured across the flats),

others use round material.

LENTON® Terminator D14

� LENTON® TERMINATOR D14 is an over-sized end anchor that creates anchorage withinthe concrete.

LENTON® TERMINATOR D14GROUP CBB65

Rebar size 10 12 16 20 25 32 40 50DesignationMetric (mm)A 33 41 52 64 80 110 130 160B 23 23 29 41 46 52 64 79D 18 19 24 36 41 46 58 72E - - - - - 25 30 40F - - - - - 80 80 80

Installation benefits

• Takes approximatelyfour turns to engage

• LENTON® uniquetaper angle providesself centering andself aligning.

• Preventscrossthreading

• One of the fastestsystems to install- No special tools or

skills required- No power required

for installation- Reduces crane time

• Acceleratesconstructionschedules

• Unique LENTON®

colour coded capaids in field assembly

13Midlands 01623 555111North 01226 730330North East 01325 381166



Sales offices:


www.erico.com

Reinforcing Bar Couplers

D

B

E

AF

A

D

LENTON® Form Saver

� LENTON® FORM SAVER, the new economical alternative for protruding dowels, is available infixed lengths with the Standard LENTON® Tapered Thread.

Other available products

LENTON® Bolt Coupler S13 provides a full-strength joint between a reinforcing barand a standard metric bolt.

LENTON® INTERLOK uses the time-tested taper thread and an inorganic grout toprovide structural integrity between load-bearing members in precast construction.

LENTON® FORM SAVERGROUP CBB72

Description SA10/400 SA12/600 SA16/650 SA20/800A 400 600 650 800D 18 18 24 36





Sales offices:14

UNIT TYPE

UNIT TYPE

M8.5S M25S

M19S

M17S

M15S

M25D

M19D

M12D

DIMENSIONS DIMENSIONSBARTYPE

BARTYPE

T10T12

T10T12

T10T12

T10T12

T10T12

T16

T16

T16

BAR SPACINGS

C150/C200

C150/C200

C150/C200

C150/C200

C150/C200

C150/C200

C150/C200

C150/C200

BAR SPACINGS

LAP LENGTH

LAP LENGTH

410500

410500

410500

410500

410500

650

650

650

Kwikastrip standard units are 1.2m long. To order, please state quantity, unit type, bar type, and bar spacing.For example: 50 no. M8.5S T10 C150. See right hand page for ordering specials.

When only the best will do….Over a period of 20 years, Kwikastrip has become established as the UK’s brand leading reinforcement continuity system. Aside of the well established advantages of using continuity strip, there are essentially 3 qualities which have earned Kwikastrip its unique market position:

Manufacturing versatility and emphasis on specials Approximately 85% of Kwikastrip is purpose-made. The aim is always to replicate the reinforcement detailer’s design in a more buildable format for the contractor. No other system can rival Kwikastrip’s total fl exibility in this regard.

Service and support from a dedicated technical team Halfen’s long experienced reinforcement team ‘eat and breathe’ Kwikastrip every day of the week, and are very able to advise regarding the scope for any given application. You might be surprised just how inventive some of the solutions can be for seemingly ‘impossible’ applications.

Product ApprovalKwikastrip was the very fi rst product ever to be awarded CARES Technical Approval status. The approval followed full-scale structural testing of the product in concrete, which concluded that the performance of joints formed using Kwikastrip were no less than that of traditional construction (i.e. with loose/unbent reinforcement). This full product approval provides critical reassurance that CARES has evaluated Kwikastrip as being ‘fi t for purpose’. Please ask for a copy of the CARES Technical Approval report.

KWIKASTRIP STANDARD RANGE GROUP CEE11





Sales offices:15

Page of

Contractor: Tel:

Site: Fax:

Drawing No(s): Date:

Schedule Ref : Detailed by:

Structural Member Bar shape

Bar mark

No. of Mbrs.

Bars each

Bars total

Ty pe & Dia.

Bar Cntrs.

HHeight

WWidth

LLap

Alength

Klength

A

B

C

D

E

KWIKASTRIP SCHEDULING FORM

1st Pour 2nd Pour

38 or 21

38R or 21R

37A or 11A20C or 00C20B or 00B37B or 11B

32X or 13X20A or 00A38D or 21D20 or 0037C or 11C

53 or 4410061 or 5177

32 or 13S37 or 11X37 or 1139 or 13D

Select the required bar shape from the above illustrations, then complete the scheduling form below and forward to your local BRC sales office. There is no need to consider individual casing lengths, as we will determine the optimum arrangement as a result of the customer-supplied information below.

For scheduling advice, radiused applications, waterproofing options, kickerless fixings contact your local BRC sales office

GROUP CEE11KWIKASTRIP SPECIALS





Sales offices:16

Black annealed 16 gauge wire for tying reinforcementbar and fabric.

18 gauge stainless steel grade 304 tying wire.

Reelfix Tying Wire SystemQuality tying wire for faster and easier steel fixing with no waste.

Reelfix is available as a disposable 2kg coil or as a refillable cartridge with belt.

Tying wire

Double loop ties and tools

Continuous high chairs

REELFIXGROUP CWW01Ref. DescriptionDispos2 Disposable 2Kg Coils

16g2k Reelfix 2Kg Mini Coil CartridgesRefill2 2Kg Cartridge Refills

LOOP TIES AND TYING TOOLSGROUP CWW20

Ref. DescriptionRDLT100 Double Loop Tie 100mmRDLT125 Double Loop Tie 125mmRDLT150 Double Loop Tie 150mmRDLT200 Double Loop Tie 200mmRDLT250 Double Loop Tie 250mmRDLT300 Double Loop Tie 300mmWTT01 Wire Tying Tool

Simple method of supporting fabric in groundfloor conditions. Supplied flat in 3.0m lengths to be formed into a circle approximately 900mm diameter on site. Manufactured fromcold reduced wire to BS4482.UsageApproximately one circular spacer per 2m2 offabric.

CIRCULAR WIRE SPACERSGROUP CSS54

Ref. Height mm Pack Qty.CS050 50 25CS060 60 25CS075 75 25CS080 80 25CS090 90 25CS105 105 25CS120 120 25CS135 135 25CS150 150 25CS165 165 25CS180 180 25CS200 200 25

Pre-stressed wire and stabilised strand are also available. Please contact your local BRC sales office for details.

Pre-stressed wire and stabilised strand

TYING WIREGROUP CWW01Ref. Description16G 16 Gauge Black AnnealedSS304 18 Gauge Stainless Steel Grade 304

CONTINUOUS HIGH CHAIRSGROUP CSS52

Ref. Height mm Pack Qty.CHL50 50 25 x 2mCHL60 60 25 x 2mCHL75 75 25 x 2mCHL80 80 25 x 2mCHL90 90 25 x 2mCHL105 105 25 x 2mCHL120 120 25 x 2mCHL135 135 25 x 2mCHL150 150 25 x 2mCHL165 165 25 x 2mCHL180 180 25 x 2mCHL200 200 20 x 2mCHL230 230CHL250 250CHL280 280

For supporting fabric in ground floor slabs and spacing fabric in walls. Supplied instandard 2m lengths. Also available inheights up to 300mm. Manufactured fromcold reduced wire to BS4482.

UsageApproximately one 2m length per 2m2

of fabric.

Special lengthsContinuous high chairs are also available inspecial lengths to order. Minimum 1m,maximum 6m in 100mm increments.

Circular wire spacers

ISO9001:2000

ISO9001:2000





Sales offices:17

CONCRETE FABRIC SPACERGROUP CSS72

Ref. Cover mm Pack Qty.CFS40/50 40 or 50 100

For the vertical and horizontal spacing ofreinforcing bar providing maximum stabilityunder normal loading conditions.

Usage4 spacers per m2.

A more flexible spacer for the vertical andhorizontal spacing of reinforcement barproviding maximum stability under normalloading conditions.


Double cover concrete spacers

For use in vertical situations providingmaximum stability under normal loadingconditions and minimising the area of spacerat the form face.


Triple cover concrete spacer

Used for the spacing of fabric at the bottom ofslabs, they have a circular base for maximumstability under normal loading conditions.


Concrete fabric spacer

A heavy duty concrete spacer simply laid onthe sub-base or formwork for the fastplacement of reinforcement.

Usage2 linear metres per m2.Available in 1m lengths.

Concrete line spacers

SINGLE COVER CONCRETE SPACERSGROUP CSS70

Ref. Cover mm Pack Qty.C20 20 1000C25 25 500C30 30 250C35 35 250C40 40 250C50 50 200C60 60 100C75 75 100

DOUBLE COVER CONCRETE SPACERSGROUP CSS70

Ref. Cover mm Pack Qty.C25/30 25 or 30 500C30/40 30 or 40 250C40/50 40 or 50 200C60/75 60 or 75 50

TRIPLE COVER CONCRETE SPACERGROUP CSS70

Ref. Cover mm Pack Qty.C35/40/50 35, 40 or 50 200

CONCRETE LINE SPACERSGROUP CSS71

Ref. Cover mmCSB25X1 25CSB30X1 30CSB40X1 40CSB50X1 50CSB60X1 60CSB75X1 75

Single cover concrete spacers





Sales offices:18

A lightweight option for the spacing of fabric atthe bottom of slabs. Their wide base givesextra stability particularly on soft blinding.


Grade plate spacers

Use for bottom spacing of fabric or bar withlight loads against formwork and particularlymetal decking. Available in 2 metre lengths.

UsageMaximum 50d spacings.

Plastic line spacers

For spacing vertical reinforcement in columnsetc. The wheels easily clip onto thereinforcement bar and minimise the area ofspacer at the form face.

UsageDependent on bar diameter.

Wheel spacers

Plastic protection caps for exposedreinforcing bar.

Safety end caps

GRADE PLATE SPACERSGROUP CSS15

Ref. Cover mm Pack Qty.GP25/30 25 or 30 250GP40/50 40 or 50 250GP65/75 65 or 75 200GP90/100 90 or 100 100

PLASTIC LINE SPACERSGROUP CSS06

Ref. Cover mm Pack Qty.AHS20 20 100mAHS25 25 100mAHS30 30 100mAHS35 35 50mAHS40 40 50mAHS50 50 50m

WHEEL SPACERSGROUP CSS13

Ref. Cover mm Bar Dia. mm Pack Qty.UW20 20 8-12 1000UW25 25 8-12 500UW30 30 8-12 500UW40 40 8-20 250UW50 50 12-20 250

SAFETY END CAPSGROUP CVV99

Ref. To Suit Bar Dia. Pack Qty.RS616 6-16 250RS1632 16-32 250RS4050 40-50 100





Sales offices:19

A waxed conical cardboard bolt box, used to formvoids and accommodate movement of holding downbolts.

Waxed cardboard bolt boxes

Core diameter for bolt is approximately 25mm. Other sizes made to order.

Use proprietary dissolving agent for removal of boltboxes.

Polystyrene bolt boxes

A general purpose, non-shrink grout as a drypowder requiring only the addition of water toproduce a free-flowing or trowellable mortar,which will maintain its original volume aftercuring.

Yield12.5 litres per 25kg bag.

General purpose grout

Holding down bolt assemblies comprising bolt,washer plate, nut and washer.

Range from 16 - 30mm in lengths 200 - 600mmdepending on grade. Grade 4.6 or 8.8 available.

Holding down bolts

WAXED CARDBOARD BOLT BOXESGROUP CVV99

Ref. Length mm Dia. Top/BotCBW225 225 70/20CBW300 300 90/20CBW375 375 100/25CBW450 450 115/30CBW525 525 115/30CBW600 600 130/30

The new standard in foundation bolt conesPlastic conical void former that eliminates the need forremoval and disposal of cardboard or polystyrene typecones. Fully enclosed base removes the need for boltadjustment.

Void form is supplied at 380mm long and can be easilycut on site to suit shorter bolts.

* Centralising cap not shown for clarity.

Void form holding down bolt sleeve

POLYSTYRENE BOLT BOXESGROUP CVV01

Ref. Length mm Dia. Top/BotCB225 225 75/40CB300 300 75/40CB375 375 75/40CB450 450 75/40CB525 525 75/40CB600 600 75/40CB750 750 75/40

GENERAL PURPOSE GROUTGROUP CCCB2Ref. Weight/PackGPG25 25kg

HOLDING DOWN BOLTSGROUP CVV99

Please contact your local BRC sales office for details

VOID FORM HOLDING DOWN BOLT SLEEVEGROUP CVV99

Ref. Length BaseHDB100x100x375mm 380mm max 115 x 115mm

Slab products




Sales offices:

20

DYNA Quell is a high swelling material usedfor effective sealing of joints in concreteconstruction. It is produced from acombination of Bentonite and Butyl rubber.This material will expand on contactwith water to seal the gaps andpores in a concrete joint.

After expanding the materialretains its elasticity so that theseal will not be affected by anysubsequent movement of thestructure.

BBA GRADE POLYTHENEGROUP CGG03Ref. Thickness Roll Width Roll Length

mµ m mDP1000 250 4 25DP1200 300 4 25

PIFA GRADE POLYTHENEGROUP CGG03Ref. Thickness Roll Width Roll Length

mµ m mPDP1000 250 4 25PDP1200 300 4 25PDP2000 500 4 12.5

TEMPORARY PROTECTIVE SHEETINGGROUP CGG03Ref. Roll Width Roll Length

m mTPSM (medium duty) 4 50TPSH (heavy duty) 4 25

JOINTING TAPEGROUP CCCB9Ref. Roll Size Pack Qty.SST (single sided) 50mm x 66m 10DST (double sided) 50mm x 66m 10

The products are available in thicknesses of� 250 microns (1000 Gauge).� 300 microns (1200 Gauge).� 500 microns (2000 Gauge).

300 micron polythene is also available as a centrefold.

Standard polythene is folded twice and supplied as a 1m wide roll.Centrefold polythene is folded once and supplied as a 2m wide roll.

Polythene and joint tape

DYNA QUELL WATERSTOPGROUP CII52Ref. Dim. Roll Size Pack size

mm mDBWATERSTOP20/25 20x25 5 8FIXINGSTRIP1 1mFIXINGNAIL 100

DYNA Quell Waterstop

Slab products




Sales offices:21

Gas protection membranesBRC offer a range of gas barriers to provideprotection against methane or radon gas. Fullycertificated, the range briefly comprises:

Radon barrierManufactured from LDPE, reinforced with astrong multifilament yarn. Typical weight is370g/m2.

Methane barrierManufactured from LDPE, reinforced with astrong multifilament yarn and aluminium foil.Typical weight is 420g/m2.

AccessoriesAlso available is a full range of ducts, vents andsumps.

ServiceNon standard panels can be produced to suit anindividual layout. This minimises cutting andwaste, as well as simplifying the laying processand ensuring that a full seal is provided.

We can provide design assistance and layoutdrawings.

A supply and fix service can also be madeavailable.

Premseal

Pipe through slab

Premseal self-adhesivemembrane star cut around pipe

Pre-formed or bitumenmastic fillet

Prembboard 'O' Seriesprotecttion board

Premseal fillet

Premseal 'O' series protection board securedwith Premstik and boards joined with Premseal reinforcing tape

Premseal self-adhesive waterproof membrane

Internal corner

Concrete parapet

Premseal self-adhesive membrane reinforced at corner

Premseal fillet Premboard 'O' series protection board

Premseal solar shield

Insulation screed shingle or paving

Premkol 701 or other approved sealant

Premboard 'O' Series protection board secured with Premstik and boards jointed with Premseal reinforcing tape

lf-adhesivePremseal semembranewaterproof m

External corner

Waterproof membranesPremseal waterproof membranes combine the very best in modern polymer laminates with traditional bitumen and polymeradhesives to form extremely tough, hard-wearing waterproof membranes for even the most stringent applications.

All Premseal membranes are designed to have excellent situation-tolerant installation properties. Specialist membranes areavailable to give protection against landfill gases such as methane, naturally occurring radioactive radon and solar radiation.

Slab products




Sales offices:22

Ref. Bar Sleeve PackDia. Length Qty.mm mm

DB20/300 20 300 100DB25/300 25 300 100DB25/375 25 375 100

Sawn end plain roundA full range of sawn end, plain round dowelbars for use in movement joints.

High yield ribbed tie-barsA full range of high yield ribbed tie-bars foruse in tied joints where movement is to berestricted.

Stainless steel dowelsSupplied to order.

Dowel bars

Plastic debonding sleeves for usein dowelled movement joints.

Dowel bar sleeves

A bituminous based compound to allow dowelbars to completely break bond with concrete.Complies with clause 1011 DOT specificationfor highways work.

Coverage1.8 - 3.6m2 per litre.

Dowel bar debonder

Rigid PVC caps with compressible filler (25mm)to allow for expansion.

Expansion dowel caps

Contraction joint cradlesHeight is to the underside of the dowel. Supplied by the half cage.

SleevesFor use with contraction joint cradles.Usage: 5 sleeves per linear metre of joint.

Expansion joint cradlesHeight is to the underside of the dowel. Supplied by the half cage.

Dowel bar cradles

DOWEL BAR DEBONDERGROUP CCCB8

Ref. Pack SizeDB005 5LDB025 25L

Ref. Bar Sleeve PackDia. Length Qty.mm mm

DB12/450 12 450 100DB16/200 16 200 100DB16/450 16 450 100

EXPANSION DOWEL CAPSGROUP CGG05

Ref. Bar Dia. mm Cap Length mm Pack Qty.D12 12 100 100D16 16 100 100D20 20 100 100D25 25 100 100D32 32 100 100D40 40 100 100

DOWEL BAR SLEEVES - GROUP CMM01

EXPANSION JOINT CRADLESGROUP CSS60

Ref. Height Slab Depth Lengthmm Range mm mm

EJC65 65 150-180 2000EJC90 90 190-230 2000EJC115 115 240-300 2000

TIE BARSGROUP CGG07

Ref. Dia. mmT10 10T12 12T16 16T20 20T25 25

DOWEL BARSGROUP CGG07

Ref. Dia. mmR10 10R12 12R16 16R20 20R25 25

CONTRACTION JOINT CRADLESGROUP CSS60

Ref. Height Slab Depth Lengthmm Range mm mm

CJC75 75 150-180 2000CJC95 95 190-230 2000CJC125 125 240-300 2000

RCPS7 Sleeves Pack qty. 100

DOWEL BAR SLEEVES - continued

Slab products




Sales offices:23

Crack inducers

Closed cell polyethylene foam strip 35kg/m3

Perforated for easy removal of top section.Standard range supplied in 2m strips.

Also available in sheets or cut to size in 10mm,12mm, 15mm, 20mm and 25mm thicknesses.

Closed cell polyethylene blanketEffective as frost protection in winter and toaid curing during summer.

Air bubble blankets and hessian blankets alsoavailable.

Frost/curing blankets

Top crack inducer (two-part)Rigid PVC extrusions for use in induced joints.Total depth of crack inducer to be 1/4 to 1/3 ofslab depth.

Bottom crack inducerRigid PVC extrusions for use in induced joints.Total depth of crack inducer to be 1/4 to 1/3 ofslab depth.

TOP CRACK INDUCERGROUP CMM07

Ref. Top Section Bottom SectionWidth/Depth Section Depthmm Depth mm mm

BF10/50/25 10/25 25 50BF10/75/25 10/25 50 75

MIOTHENE JOINT FILLERGROUP CMM20

Ref. Width Thickness Perforatedmm mm mm from

edgeS100/10/10 100 10 10S140/10/10 140 10 10S150/12/12 150 12 12S150/20/20 150 20 20S175/12/12 175 12 12S175/20/20 175 20 20S200/12/12 200 12 12S200/20/20 200 20 20

FROST/CURING BLANKETGROUP CMM10

Ref. DescriptionFB75X2/10 75 x 2m blanket, 10mm thick

BOTTOM CRACK INDUCERGROUP CMM05

Ref. Section Depth mmCY40 Y 40CY50 Y 50CY75 Y 75

Concrete screed rail for accurate floor levelswithout the need to strike traditional road forms.

Concrete screed rails CONCRETE SCREED RAILSGROUP CPP11Ref. Height mm Length m Rails Per

BundleBR50 50 3 104BR100 100 3 48BR125 125 3 33BR150 150 3 27

Miothene joint filler

Plastic screed chairs are fullyadjustable and ideal for lightweightapplications. Use with a 50mmdiameter tube. Shaft is supplied in 2m lengths to be cut on site.

Metal screed chairs are fullyadjustable and supplied in two parts. Height is adjusted usingthread.

Screed chairs PLASTIC SCREED CHAIRSGROUP CGG01

Ref. DescriptionSCS SaddleSCC CollarSCB BaseT22 22mm Tubing for Shaft

METAL SCREED CHAIRSGROUP CGG01

Ref. Height Range mmMSC115-150 115-150MSC145-205 145-205MSC195-310 195-310MSC285-405 285-405

Slab products

Sales offices:24




PermaSteel is a low cost ‘leave-in-place’, light duty applicationscreed rail that takes the conceptof ‘leave-in-place’ formwork ontothe next stage. Using Permaban’sexperience in constructing floorsand formwork design, other ‘allsteel’ formwork systems wereexamined in depth and in everycase design or installation faultswere evident in some way.Permaban addressed theseshortcomings with thedevelopment of PermaSteel.

In addition PermaSteel provides some arris support,accommodates dowel bars, acts as a crack inducer and can be supplied with a sealantvoid former. Permasteel rails are easy to handle and transport as the weight is low and they are delivered in bundles that can be stacked.

PermaSteel

PERMASTEEL ALL STEEL SCREED RAILSGROUP CPP99Ref. Height mm Length mType 1MSR115mmx3m 115 3MSR155mmx3m 155 3PERMASTEEL/LFEET 115/155 extra feet*Type 1 comes with 3 feet. If a Bunyan striker is usedthen employ at least 4 feet per 115mm rail and 5 forthe 155mm.

Type 2MSR40mmx3m 40 3MSR70mmx3m 70 3SSVF Void former 3

For heavy duty applications, please use theAlphaJoint range of products.

Type 1

Type 2

Optional Sealant Void Former

BetaJoint

BETATOPGROUP CPP99Ref. Height mm Length mBDP-TP/SD-100 100 3BDP-TP/SD-125 125 3BDP-TP/SD-150 150 3BDP-TP/SD-175 175 3BDP-TP/SD-200 200 3

BETASTRIPGROUP CPP99Ref. Height mm Length mBDP-SP/SD-100 100 3BDP-SP/SD-125 125 3BDP-SP/SD-150 150 3BDP-SP/SD-175 175 3BDP-SP/SD-200 200 3

BETAJOINTGROUP CPP99Ref. Height mm Length mB-JT100 100 3B-JT125 125 3B-JT150 150 3B-JT175 175 3B-JT200 200 3

An easily installed, adjustable ‘leave-in-place’ formwork system for light tomedium duty applications with bolt-on leave-in-place’ feet, or use PermabanAlphaFix removable fixing system to provide ’Micrometer’ adjustment forsuperflat floors.

BetaStrip 2mm wide or BetaTop12mm wide screed rail for tied jointsor BetaJoint for contraction joints.

Available for 100mm to 225mm deepslabs and easily adjustable to level.Load transfer by 6mm DiamondDowels, round or square dowel, or tie bar.

Special Beta-products available forslab depths up to 400mm deep.

BetaJoint

BetaStrip BetaTop

ALPHAJOINTGROUP CPP21Ref. Height mm Length mDD6-120/140/150/175 150-200 3DD6-225 201-250 3AD10-120/140/150/175 150-200 3AD10-7-225 201-250 3AD10-7-250/275 251-300 3

Permaban AlphaJoint gives concrete floorsenhanced performancefrom free contractionjoints. It incorporatespatented systems of loadtransfer across joints,which enhance the loadingvalue of the concrete floor.AlphaJoint satisfies therequirements in ConcreteSociety TR34 and BS8204-2: 1999 for load transferand arris protection inheavy duty concrete floor slabs.

AlphaJoint

w/Alpha Dowel

w/AlphaFeet

w/AlphaFix

w/Diamond Dowel

Slab products




Sales offices:25

Permaban Dowel Systems providesuperior load transfer across thejoint compared to traditional round dowels. These innovationsspread stress over the full width of the dowel.

Permaban dowels allow sub basepreparation right up to the slab edge.

Permaban dowel systems eliminate vertical joint movementwhile allowing two-way lateral jointmovement between adjacent bays of the concrete slab.

Dowel systems

This new product allows virtually anymanhole to be isolated andfinished with far greater ease than before. It reduces the need to finish the awkward detailingaround these objects during themiddle of a large flood pour of concrete.

Each surround has jacking studs to giveaccurate adjustment to height and level aswell as effective load transfer featuresusing Permaban Diamond Dowels.

MANHOLE SURROUNDSGROUP CPP40Ref. Height mm Length mMHS-150-1000 150 1 x 1MHS-150-1500 150 1.5 x 1.5MHS-150-2000 150 2 x 2MHS-150-3000 150 1.5 x 3MHS-175-1000 175 1 x 1MHS-175-1500 175 1.5 x 1.5MHS-175-2000 175 2 x 2MHS-175-3000 175 1.5 x 3MHS-200-1000 200 1 x 1MHS-200-1500 200 1.5 x 1.5MHS-200-2000 200 2 x 2MHS-200-3000 200 1.5 x 3

Manhole surrounds

■ Composite flooring systems■ Pumpable flooring systems■ Terrazzo styling techniques■ Dry-Shake floor toppings■ PermaSeal floor sealant systems■ PermaFlex joint sealant systems

Other products

www.permaban.com

Alpha Dowel

PermaSleeve

Tri-Plate

Diamond Dowel

DOWEL SYSTEMSGROUP CGG07AD10-CS-NT Alpha DowelDD6-CS-NT Diamond DowelTR10 or 6 Tri-Plate

PERMASLEEVEGROUP CGG07Square dowel barGROUP CMM01Sleeve for square dowel bar

Slab products




Sales offices:26

Mould release oilA high quality mould oil for general site and precast yard use that achieves a topquality concrete finish in most situations.BCA category 2.UKWFBS listed.Spray or brush applied. Coverage: 20-30m2 per litre.

Chemical release agentSpecially blended reactive oils which give a high quality finish with mostformwork types.BCA category 5.UKWFBS listed.Spray applied. Coverage: 30-50m2 per litre.

Release

A surface hardener for new and old concrete floors to provide dustproofing andincrease durability.Brush applied. Coverage: 6m2 per litre (dependent on floor porosity).

Surface hardening and dustproofing

To provide an exposed aggregate finish for concrete or a key for subsequent pours.

Mould face For application to mould face prior to placing of concrete.Brush applied. Coverage: 15-16m2 per litre.

Top faceFor treatment to the top face of freshly cast concrete.Spray applied. Coverage: 5m2 per litre.

Surface retarders

Plastic and metal sprayer units

Sprayers

Curing compound – silicate basedAn aqueous solution of metalic silicates as a general curing aid. Also available tinted.UKWFBS listed.Spray applied. Coverage: 5.5-6m2 per litre.

Curing compound – resin basedFormulated with inert hydrocarbon resins to give excellent film and moisture retention. 90% efficiency rating.UKWFBS listed.Spray applied. Coverage: 5.5-6m2 per litre.

Curing and sealing compoundA clear acrylic polymer resin solution for application to surfaces of freshly laidconcrete to form a highly effective curing membrane and an in-depth sealer. 75% efficiency ratingSpray applied. Coverage: 6m2 per litre.

Water-based curing productsWater-based curing products are also available.Please contact your local BRC sales office for details.

MOULD RELEASE OILGROUP CCCB1

Ref. SizeMRO005 5LMRO025 25LMRO205 210L

Curing

SURFACE HARDENINGGROUP CCCB5

Ref. SizeSH025 25LSH200 210L

SURFACE RETARDERSGROUP CCCA4

Ref. Type SizeAMFS005 Mould Face Retarder 5LAMFS025 Mould Face Retarder 25LATFS005 Top Face Retarder 5LATFS025 Top Face Retarder 25LATFS205 Top Face Retarder 210L

SPRAYERSGROUP CCCN7

Ref. Type SizePLT1 Plastic 7LPLT125 Plastic 12.5LLMS07 Metal 9LLMS11 Metal 11L

CURING & SEALING COMPOUNDSGROUP CCCB5

Ref. Type SizeSCA025 Silicate Based 25LSCA205 Silicate Based 210LCM025 Resin Based 90% 25LCM205 Resin Based 90% 210LCSC025 Curing & Sealing 25LCSC205 Curing & Sealing 210L

CHEMICAL RELEASE AGENTGROUP CCCB1

Ref. SizeCRA25 25LCRA205 210L

H

Formwork




Sales offices:27

Formwork joint tapeA multi-purpose PVC adhesive tapein roll size 50mm x 33m.To assist in joint applications.

Rubber stopperFor sealing sleeve after a concrete pour.26mm diameters also available to suit 20mm tie rod.

Grout check foam tapeClosed cell tape for sealing formwork in rollsizes 12mm x 6mm and 24mm x 12mm.Helps to reduce grout loss.

Plastic sleeveTo allow the tie rod to be retrieved.To suit a 15mm tie rod system the sleeve has a22mm internal diameter.26mm also available to suit 20mm tie rod.

Plastic conesA 22mm diameter plastic cone to fit inside a22mm plastic sleeve.26mm also available to suit 20mm tie rod.

THREADED TIE BAR SYSTEMGROUP CTT08

Ref. DescriptionTTR 15mm Rod (6m Length)TTR20 20mm Rod (6m Length)TWN 15mm Wing Nut TWN20 20mm Wing Nut TPH Waler plate 120 x 120 x 12mm TPH20 Waler plate 120 x 120 x 12mm

FORMWORK TAPEGROUP CCCN1

Ref. Roll sizeFWT 50mm x 33m

GROUT CHECK FOAM TAPEGROUP CCCB9Ref. Roll sizeSF1210 12mm x 6mm x 10mSF2405 24mm x 12mm x 5m

PLASTIC CONESGROUP CTT02

Ref. Tube I.D. mmK22 22K26 26

PLASTIC SLEEVEGROUP CTT01

Ref. Internal Dia. mmT22 22T26 26

CHAMFER CORNER PROFILEGROUP CTT08

Ref. Type H mmCF10 Plain 10CF15 Plain 15CF20 Plain 20CF25 Plain 25CFF10 with Flange 10CFF15 with Flange 15CFF20 with Flange 20CFF25 with Flange 25

Formwork accessoriesChamfer corner profileA triangular plastic strip in 2.5m lengths. To form a chamfer in concrete columns. Available with or without a nailing flange.

Threaded formwork tie bar systemTie rod For securing formwork.Coarse self-cleaning threaded bar with a corediameter of 15mm and an overall diameter of 17mm.Available in 6m, 3m, 2m, 1.5m and 1.2m lengths.The ultimate fail load is 180KN.Also available in 20mm.

Wing nutTo suit a 15mm tie rod. Also available for 20mm tie rod.

Waler plates, hexagon nuts, connectors, water barriers, rock anchorsAll items are compatible with the 15mm tie rod system.Also available for 20mm tie rod.

RUBBER STOPPERGROUP CTT08

Ref. Tube I.D. mmF22 22F26 26

Column corner guards

Rapidobat




Sales offices:28

Formwork

RapidobatRound columns made easy!Rapidobat is a purpose made spirally wound rigid paper tube of extremely highquality. The tube is internally lined with a smooth faced plastic release sheetwhich provides the ultimate in concrete surface finish and appearance. Rapidobatis the fast and economical solution to the problems of forming round columnswhich is complicated with timber formwork and expensive with GRP or steelformwork. Rapidobat incorporates a unique and patented tear off strip whichmeans that stripping is achieved in a matter of seconds - without any risk ofdamage to the concrete face. Importantly, after column inspection, the strippedRapidobat tube then provides physical protection from potential site damage tothe attractive newly cast column.

®

Materials: Mild steel plate - hot dip galvanised, powder ornylon coated (colour to order).Stainless steel - standard mill finish orsatin/mirror polished.

Sizes: Standard 50 x 50 x 3mm x 1200mm long. Formed to various radii, lengths as required.

Fixings: Cast-in applications - anchors and threadedfixing points.Surface fix applications - countersunk holes.

RAPIDOBATGROUP CTT99Tube Internal Tube Wall Maximum PourDiameter (mm) Thickness (mm) Height (m)*150 4.5 12.30200 4.5 10.25240 5.0 10.25250 5.0 10.25300 5.0 10.25350 5.0 8.79360 5.0 8.79400 6.0 7.69435 6.0 7.00450 6.5 6.50500 7.0 7.30560 7.0 6.80600 8.0 6.15650 8.5 6.00700 9.5 7.03750 10.0 7.03800 10.5 7.69900 12.0 7.701000 13.5 7.65

COLUMN CORNER GUARDSGROUP CTT04Please contact your local BRC sales office for details

* The maximum recommended pour height of concrete in consideration of the internal pourpressure related to tube diameter and wall thickness.

� Use to form openings in concrete slabs.

� Shuttering strips are perforatedcrosswise every 50mm.

� The surface profile ensures proper bondto the concrete.

Shuttering StripsSHUTTERING STRIPSGROUP CPP50

Type Height Roll sizeSF15 150 mm 10 mSF17 175 mm 10 mSF18 180 mm 10 mSF22 225 mm 10 mSF25 250 mm 10 mSF27 275 mm 10 mSF30 300 mm 10 m

29Midlands 01623 555111North 01226 730330North East 01325 381166



Sales offices:

Formwork

Locking Steel Kickers

W E D G E L O C K

Speed Edge Formwork� Leave in place formwork for ground

supported slabs or bases.

� Self-supporting.

� Fast installation.

� Standard 2.25m long units.

LOCKING STEEL KICKERSGROUP CTT09

Type Wall width mmLSK150 150LSK175 175LSK200 200LSK225 225LSK250 250Other sizes are available on request

SPEED EDGE FORMWORKGROUP CPP60

Type B H Length(mm) (mm) (m)

R150 120 150 2.25 mR175 120 175 2.25 mR200 120 200 2.25 mR250 155 250 2.25 mR300 180 300 2.25 m

� Eliminates the need for costly set-up ofkicker shutttering.

� Ready to use.

� Fast and easy adjustment.

� Long body giving solid fixing.

� No tools required.





Sales offices:30

APPROX. WEIGHT KG/FT2

SPECIFICATION SELF COLOUR GALVANISED2 x 1 x 3.10mm 0.31 0.332 x 2 x 3.10mm 0.21 0.223 x 1/2 x 3.10mm 0.48 0.503 x 1 x 3.10mm 0.28 0.293 x 3 x 3.10mm 0.14 0.154 x 4 x 3.10mm 0.11 0.121 x 1 x 2.50mm 0.27 0.2911/2 x 11/2 x 2.50mm 0.18 0.192 x 1 x 2.50mm 0.20 0.222 x 2 x 2.50mm 0.14 0.153 x 1/2 x 2.50mm 0.32 0.343 x 1 x 2.50mm 0.18 0.19

4.8mm

2 x 23 x 33 x 675mm x 25mm x4.80/3.00mm

4.0mm

1 x 12 x 12 x 23 x 1/23 x 3

3.1mm

1 x 111/2 x 11/2

2 x 12 x 23 x 1/23 x 13 x 34 x 4

2.5mm

1 x 111/2 x 11/2

2 x 12 x 23 x 1/23 x 1

0.7mm1/4 x 1/4

1.0mm1/2 x 1/2** 1/2 x 1**1 x 1**

1.6mm1/2 x 1/21/2 x 1*3/4 x 3/4**1 x 1**2 x 2

Pre-galvanised Weldmesh2.5mm

2 x 2 50mm x 50mm

3.0mm

2 x 2 50mm x 50mm

Stainless steel Weldmesh 304 spec.3.0mm

3 x 1/21 x 12 x 2

2.5mm

3 x 1/21 x 12 x 2

1.6mm1/2 x 1/21 x 1

Weldmesh gauges guide

APPROX. SIZE mmSELF COLOUR GALVANISED

22g 0.66 0.7019g 0.91 1.0016g 1.52 1.6014g 1.93 2.0012g 2.44 2.5010g 3.00 3.108g 3.88 4.006g 4.69 4.80

APPROX. WEIGHT KG/FT2

SPECIFICATION SELF COLOUR GALVANISED2 x 2 x 4.80mm 0.51 0.523 x 3 x 4.80mm 0.34 0.353 x 6 x 4.80mm 0.26 0.2775mm x 25mmx 4.80mm/3.10mm 0.38 0.401 x 1 x 4.00mm 0.71 0.742 x 1 x 4.00mm 0.52 0.542 x 2 x 4.00mm 0.35 0.363 x 1/2 x 4.00mm 0.80 0.833 x 3 x 4.00mm 0.23 0.241 x 1 x 3.10mm 0.41 0.4311/2 x 11/2 x 3.10mm 0.28 0.29

Weldmesh size range – weight guide.To convert the panel weight into Kg/m2 multiply the Kg/ft2 value by 10.76

Quality standardsGauge sizesDimensions shown are for galvanised wire.Weldmesh self-colour specifications will vary between 0.04mm and 0.12mm below thegalvanised wire dimension as shown in the Weldmesh Gauges Guide.

Galvanised WeldmeshThrough our unique smooth inline galvanised process, Weldmesh is hot dip galvanisedto the highest standards and conforms to BS EN 10244-2 Class A. Should a thicker coatbe necessary, i.e. BS EN ISO 1461 (replaces BS729), this can be obtained on request.Pre-galvanised Weldmesh (mesh made from galvanised wire) can also be produced onrequest.

FLAT ON EDGE SPECIFICATION PANEL WEIGHTEDGE ON EDGE MESH x WIRE SIZES (Kg)

Panel size:1200mm x 2400mm 50 x 50 x 4/2mm 7.24Finish: Self Colour(bright wire) 25 x 25 x 4/2mm 14.25

50 x 50 x 5/2.50mm 11.3125 x 25 x 5/2.50mm 22.27

50 x 50 x 6/3mm 16.2825 x 25 x 6/3mm 32.07

Heavy Weldmesh rangeGalvanised after manufacture and self colour finish

Light Weldmesh rangeGalvanised after manufacture

Weldmesh flat Self colour finish

* Also available pre-galvanised** Also available self colour





Sales offices:31

MATTRESSESGROUP LRH75

Corrosion ProtectionZincalu Super (95% Zn / 5% Al)Mesh Size 76.2mm x 76.2mm

Ref: Mattress Dimensions Wire diameter75300MC1 3m x 2m x 0.150m 3mm75300MC2 3m x 2m x 0.225m 3mm75300MC7 3m x 2m x 0.300m 3mm75300MC4 6m x 2m x 0.150m 3mm75300MC5 6m x 2m x 0.225m 3mm75300MC3 6m x 2m x 0.300m 3mm

Also available in 4.5mm wire and PVC coated on galvanised wire

The use of gabions as an effective solution to combat erosion and tostabilise and strengthen embankments has been in evidence forseveral centuries.

Rivers, coasts roads and railways can all be subject to continuous orfluctuating erosion, demanding planned defences that counteract theforces involved.

Concertainer gabions are used in many modern civil engineeringschemes to provide economic and effective solutions.

In recent years Betafence Ltd have concentrated on quality ofmaterials, manufacture and installation techniques resulting inextensive use for civil engineering and architectural applicationswhere quality and aesthetics are paramount.

All Concertainer gabions and mattresses are BBA certified for Roads& Bridges and General Building Regulations.

Weldmesh Concertainer Gabions and MattressesGABIONSGROUP LRH75

Corrosion ProtectionZincalu Super (95% Zn / 5% Al)Mesh Size 76.2mm x 76.2mm

Ref: Gabion Dimensions Wire diameter75300GC1 1m x 1m x 0.5m 3mm75300GC2 1m x 1m x 1m 3mm75300GC17 1.5m x 1m x 0.5m 3mm75300GC9 1.5m x 1m x 1m 3mm75300GC3 2m x 1m x 0.5m 3mm75300GC4 2m x 1m x 1m 3mm75300GC5 3m x 1m x 0.5m 3mm75300GC6 3m x 1m x 1m 3mm75300GC7 4m x 1m x 0.5m 3mm75300GC8 4m x 1m x 1m 3mm

Also available in 4.5mm wire and PVC coated on galvanised wire

Other BRC companies

34

ISO9001:2000

BRCA division of BRC Limited

CONDITIONS OF SUPPLY

1. Interpretation1.1 In these Conditions:

"Buyer" means the party which accepts a quotation given to itby the Seller for the sale of the Goods.

"Conditions" means the standard terms and conditions ofsupply set out in this document and (unless the contextotherwise requires) includes any special terms and conditionsagreed in Writing between the Buyer and the Seller.

"Contract" means the contract for the sale and purchase of theGoods.

"Goods" means the goods set out in the Quotation (includingany instalment of the goods or any part of them) which theSeller is to supply in accordance with these Conditions.

"Order Confirmation" means confirmation given by the Seller tothe Buyer that the Seller agrees to supply an order of the Buyeron these Conditions.

"Price" means the price of the Goods.

"Quotation" means a quotation given by the Seller to the Buyeron the basis of these Conditions.

"Seller" means BRC Limited of Edstone Hall, Wootton Wawen,Solihull, B95 6DD. Registered in England No. 3721267.

"Specification" includes any plans, drawing, data, formulae,instructions or other information relating to the Goods.

"Writing" includes facsimile transmission and comparablemeans of communication.

1.2 Any reference in the Conditions to a statute or aprovision of a statute shall be construed as a reference to thatstatute or provision as amended, re-enacted or extended at therelevant time.

1.2 The headings in these Conditions are for convenienceonly and shall not affect their interpretation.

2. Basis of Purchase2.1 The Quotation shall constitute an invitation to treat bythe Seller.

2.2 An order submitted by the Buyer shall constitute anoffer by the Buyer to purchase the Goods subject to theseConditions.

2.3 No order shall be accepted or deemed to be accepted bythe Seller unless and until confirmed in Writing by the Seller’sauthorised representative by way of Order Confirmation.

2.4 All quotations made by the Seller in respect of materialex-stock are subject to the material being in stock at the timethe Buyer’s order is received and the Seller accepts no liabilityshould such material be sold before the Buyer’s order isreceived.

2.5 The Seller shall supply and the Buyer shall acquire theGoods in accordance with the Seller’s Order Confirmationsubject to these Conditions, which shall govern the Contract tothe exclusion of any other terms and conditions subject towhich any such quotation is accepted or purported to beaccepted, or any such order is made or purported to be made,by the Buyer.

2.6 No variation to these Conditions shall be binding unlessagreed in Writing between the authorised representatives of theBuyer and the Seller.

2.7 The Seller’s employees or agents are not authorised tomake any representations concerning the Goods unlessconfirmed by the Seller in Writing. In entering into the Contractthe Buyer acknowledges and agrees that it does not rely on anysuch representations which are not so confirmed.

2.8 Any advice or recommendation given by the Seller or itsemployees or agents to the Buyer or its employees or agents asto the storage, application or use of the Goods which is notconfirmed in Writing by the Seller is followed or acted uponentirely at the Buyer’s own risk, and accordingly the Seller shallnot be liable for any such advice or recommendation which isnot so confirmed.

2.9 Any typographical, clerical or other error or omission inany sales literature, quotation, price list, acceptance of offer,Order Confirmation, invoice or other documentation orinformation issued by the Seller shall be subject to correctionwithout any liability on the part of the Seller.

2.10 The Buyer shall be responsible for the efficacy orotherwise of any information, advice or instructions regardingthe Goods given by the Buyer or attached to the Goods and theBuyer shall be liable for and shall indemnify the Seller againstall losses, damages, costs and expenses incurred by the Selleror awarded against the Seller in connection with or arising fromsuch information, advice or instructions.

2.11 Where the Contact provides for testing and inspection ofthe goods before delivery, the Buyer may carry out testingand/or inspection of the Goods at its own expense and at theSeller’s producing works within 7 days of notification by theSeller to the Buyer that the Goods are ready for delivery. TheBuyer shall pay for all test pieces which comply with theSpecification.

2.12 At the expiry of 7 days from the notification referred to in2.11, the Seller shall be entitled to deliver the Goods to theBuyer as provided in these Conditions whether or not the Buyerhas carried out any testing or inspection.

3. Orders and Specifications3.1 No order submitted by the Buyer shall be deemed to beaccepted by the Seller unless and until confirmed in Writing bythe Seller’s authorised representative by way of OrderConfirmation.

3.2 The Buyer shall be responsible to the Seller for ensuringthe accuracy of the terms of any order (including any applicablespecification) submitted by the Buyer, and for giving the Sellerany necessary information relating to the Goods within asufficient time to enable the Seller to perform the Contract inaccordance with its terms.

3.3 The quantity, quality and description of the Goods shall,subject as provided in these Conditions, be as specified in theQuotation and/or in any applicable Specification supplied by theBuyer to the Seller or agreed in Writing by the Buyer.

3.4 The Seller reserves the right to make any changes in thespecification of the Goods and the substances, chemicals andmaterials used to manufacture the Goods but any such changesshall not materially affect the quality or performance of theGoods.

3.5 The Goods shall be supplied subject to the tolerancesset out in the Seller’s catalogue and sales literature when theContract is made.

3.6 If the Goods are to be manufactured or any process is tobe applied to the Goods by the Seller in accordance with aspecification submitted by the Buyer, the Buyer shall indemnifythe Seller against all loss, damages, costs and expensesawarded against or incurred by the Seller in connection with orpaid or agreed to be paid by the Seller in settlement of anyclaim for infringement of any patent, copyright, design, trademark or other industrial or intellectual property rights of anyother person which results from the Seller’s use of the Buyer’sspecification.

3.7 No order which has been accepted by the Seller may becancelled by the Buyer except with the agreement in Writing ofthe Seller and on the terms that the Buyer shall indemnify theSeller in full against all loss (including loss of profit), costs(including the cost of all labour and materials used), damages,charges and expenses incurred by the Seller as a result ofcancellation.

4. Price4.1 Subject to 4.2, the Price shall be the Seller’s ruling priceas at the date of delivery of the Goods. Payment shall be madein sterling unless otherwise agreed.

4.2 The Seller reserves the right, by giving notice to theBuyer at any time before delivery, to increase the Price beyondthe ruling price referred to in clause 4.1 to reflect any increasein the cost to the Seller which is due to any factor beyond thecontrol of the Seller (such as, without limitation, any foreignexchange fluctuation, introduction of the Euro. currencyregulation, alteration of duties, significant increase in the costsof labour, materials and other costs of manufacture), anychange in delivery dates, quantities or specifications for theGoods which is requested by the Buyer, or any delay caused byany instruction of the Buyer or failure of the Buyer to give theSeller adequate information or instructions.

4.3 Except as otherwise stated under the terms of anyquotation and unless otherwise agreed in Writing between theBuyer and the Seller, the Price shall be on an ex works basis,and where the Seller agrees to deliver the Goods otherwisethan at the Seller’s premises, the Buyer shall be liable to paythe Seller’s additional charges for transport, packaging andinsurance.

4.4 The Price and any additional charges payable hereundershall be exclusive of any applicable value added tax or other taxor duty relating to the sale or delivery of the Goods, which theBuyer shall be additionally liable to pay to the Seller.

4.5 The cost of pallets and containers unless otherwiseagreed in writing between the Buyer and the Seller will becharged to the Buyer in addition to the Price.

5. Terms of Payment5.1 Subject to any special terms agreed in Writing betweenthe Buyer and the Seller, the Seller shall be entitled to invoicethe Buyer for the Price on or at any time after delivery of theGoods, unless the Goods are to be collected by the Buyer or theBuyer wrongfully fails to take delivery of the Goods, in whichevent the Seller shall be entitled to invoice the Buyer for theprice at any time after the Seller has notified the Buyer that theGoods are ready for collection or (as the case may be) theSeller has tendered delivery of the Goods.

5.2 The Buyer shall pay the Price by the last day of thecalendar month following delivery and the Seller shall beentitled to recover the Price, notwithstanding that deliverymight not have taken place and the property in the Goods hasnot passed to the Buyer. The time of payment of the Price shallbe of the essence of the Contract. Receipt for payment will beissued only upon request.

5.3 All amounts due under these Conditions shall be paid infull without any deduction or withholding and the Buyer shallnot be entitled to assert any credit set-off or counterclaimagainst the Seller in order to justify withholding payment of anysuch amount in whole or in part.

5.4 If the Buyer fails to make any payment on the due datethen, without prejudice to any other right or remedy available tothe Seller, the Seller shall be entitled to:

5.4.1 cancel the Contract or suspend any further deliveries tothe Buyer;

5.4.2 appropriate any payment made by the Buyer to such ofthe Goods or the Services (or the goods or services suppliedunder any other contract between the Buyer and the Seller) asthe Seller may think fit (notwithstanding any purportedappropriation by the Buyer); and

5.4.3 charge the Buyer interest from the due date up to thedate of actual payment in full (both before and after anyjudgement) on the amount unpaid, at the rate of 4 per cent perannum above Barclays Bank base rate from time to time. Suchinterest shall accrue on a daily basis and be compoundedquarterly.

6. Delivery6.1 Delivery of the Goods shall be made by the Buyercollecting the Goods at the Seller’s premises at any time afterthe Seller has notified the Buyer that the Goods are ready forcollection on payment of the collection charge then specified inthe Seller’s price list or, if some other place for delivery isagreed by the Seller, the Seller delivery the Goods to that place.

6.2 In the event that the Seller is to deliver the Goods otherthan by making the same available for collection at itsproducing works, the method of carriage shall, unlessotherwise agreed in Writing, be at the discretion of the Seller.Any transport or freight arranged or undertaken by the Sellershall be arranged or undertaken as agent for the Buyer and theSeller shall have no liability for any loss or damage to theGoods after the same have left the Seller’s premises. TheSeller may supply the Goods from any of its producing works.

6.3 The Seller shall only be obliged to deliver the Goods to asafe and suitable site at the place of delivery such as an area ofhard standing. The Seller shall decide in its absolutediscretion upon the safeness and suitability of any such site.

6.4 The Seller reserves the right to charge to the Buyer anycosts, charges or expenses incurred by the Seller as a result ofvehicle detention or demurrage of ships in consequence of anyact or omission of the Buyer, its employees or agents, or as aresult of special requirements or stipulations of the Buyer notprovided for in the Contract.

6.5 Any dates quoted for delivery of the Goods areapproximate only and the Seller shall not be liable for any delayin delivery of the Goods howsoever caused. Time for deliveryshall not be of the essence of the Contract. The Goods may bedelivered by the Seller in advance of the quoted delivery dateupon giving reasonable notice to the Buyer.

6.6 Where the Goods are to be delivered in instalment, eachdelivery shall constitute a separate contract and failure by theSeller to deliver any one or more of the instalments inaccordance with these Conditions or any claim by the Buyer inrespect of any one or more instalments shall not entitle theBuyer to treat the Contract as a whole as repudiated.

6.7 If the seller fails to deliver the Goods (or any instalment)for any reason other than any cause beyond the Seller’sreasonable control or the Buyer’s fault, and the Seller isaccordingly liable to the Buyer, the Seller’s liability shall belimited to the excess (if any) of the cost to the Buyer (in thecheapest available market) of similar goods to replace thosenot delivered over the Price.

6.8 If the Buyer fails to take delivery of the Goods within 7days of notification that the Goods are ready for collection orfails to give the Seller adequate delivery instructions at the timestated for delivery (otherwise than by reason of any causebeyond the Buyer’s reasonable control or by reason of theSeller’s fault) then, without prejudice to any other right orremedy available to the Seller, the Seller may:

6.8.1 deliver the Goods to the Buyer’s address on the Buyer’sorder; or

6.8.2 store the Goods until actual delivery and charge theBuyer for the reasonable costs (including insurance) of storage:or

6.8.3 sell the Goods at the best price readily obtainable and(after deducting all reasonable storage and selling expenses)charge the Buyer for any shortfall below the price under theContract.

7. Risk and Property7.1 Risk of damage to or loss of the Goods shall pass to theBuyer:-

7.1.1 in the case of the Goods to be delivered at the Seller’spremises, at the time when the Seller notifies the Buyer thatthe goods are available for collection; or

7.1.2 in the case of Goods to be delivered otherwise than atthe Seller’s premises, after the time the Goods have left theSeller’s premises.

7.2 Notwithstanding delivery and the passing of risk in theGoods, or any other provision of these Conditions, the propertyin the Goods shall not pass to the Buyer until the Seller hasreceived in cash or cleared funds payment in full of the Priceand the price of all other goods and services agreed to besupplied by the Seller to the Buyer for which payment is thendue.

7.3 Until such time as the property in the Goods passes tothe Buyer, the Buyer shall hold the Goods as the Seller’sfiduciary agent and bailee, and shall keep the Goods separatefrom those of the Buyer and third parties and properly storedand protected and insured and identified as the Seller’sproperty, but shall be entitled to resell or use the Goods in theordinary course of its business.

7.4 Until such time as the Property in the Goods passes tothe Buyer (and provided the Goods are still in existence andhave not been resold), the Seller shall be entitled at any time torequire the Buyer to deliver up the Goods to the Seller and, ifthe Buyer fails to do so forthwith, to enter upon any premises ofthe Buyer or any third party where the Goods are stored andrepossess the Goods.

7.5 The Buyer shall not be entitled to pledge or in any waycharge by way of security for any indebtedness any of the Goodswhich remain the property of the Seller, but if the Buyer doesso all moneys owing by the Buyer to the Seller shall (withoutprejudice to any other right or remedy of the Seller) forthwithbecome due and payable.

7.6 The Seller shall have a first and paramount lien over anygoods or property of the Buyer in its possession for all sumsdue and payable to the Seller.

7.7 Risk of damage to or loss of any free issue materialsupplied by the Buyer to the Seller shall remain at all time withthe Seller who shall bear full responsibility for insuring orotherwise safeguarding such material.

8. Warranties and Liability8.1 Subject to the conditions set out below the Sellerwarrants that the Goods will correspond with the Specificationat the time of delivery.

8.2 The above warranty is given by the Seller subject to thefollowing conditions:

8.2.1 the Seller shall be under no liability in respect of anydefect in the Goods arising from any Specification supplied bythe Buyer;

8.2.2 the Seller shall be under no liability in respect of anydefect arising from fair wear and tear, wilful damage,negligence, improper or unsuitable storage conditions,abnormal working conditions, failure to follow the Seller’sinstructions (whether oral or in writing), misuse or alteration ofthe Goods without the Seller’s approval;

8.2.3 the Seller shall be under no liability under the abovewarranty (or any other warranty, condition or guarantee) if thetotal Price has not been paid by the due date for payment;

8.2.4 the above warranty does not extend to goods ormaterials not manufactured by the Seller, in respect of whichthe Buyer shall only be entitled to the benefit of any suchwarranty or guarantee as is given by the manufacturer to theSeller.

8.3 Subject as expressly provided in these Conditions allwarranties, conditions or other terms implied by statute orcommon law are excluded to the fullest extent permitted bylaw.

8.4 Any claim by the Buyer which is based on any failure ofthe Goods to correspond with the Specification shall (whetheror not delivery is refused by the Buyer) be notified to the Sellerwithin 7 days from the date of delivery or (where the defect orfailure was not apparent on reasonable inspection) within areasonable time after discovery of the defect or failure and inany event within 30 days of delivery. If delivery is not refused,and the Buyer does not notify the Seller accordingly, the Buyershall not be entitled to reject the Goods and the Seller shallhave no liability for such defect or failure, and the Buyer shallbe bound to pay the Price as if the Goods had been delivered inaccordance with the Contract.

8.5 Where any valid claim in respect of any of the Goodswhich is based on any defect in quality or condition thereof ortheir failure to meet the Specification is notified to the Seller inaccordance with these conditions the Buyer shall give the Sellera reasonable opportunity to inspect the Goods prior to use orprocessing. The Seller shall be entitled to replace the Goods(or the part in question) free of charge or, at the Seller’s solediscretion, refund to the Buyer the Price (or a proportionatepart of the price), but the Seller shall have no further liability tothe Buyer.

8.6 Except in respect of death or personal injury caused bythe Seller’s negligence, the Seller shall not be liable to theBuyer by reason of any implied warranty, condition or otherterm, or any duty at common law, or under the express termsof the contract, for any indirect, special or consequential loss ordamage (whether for loss of profit or otherwise), cost, expensesor other claims for compensation whatsoever (whether causedby the negligence of the Seller, its employees or agents orotherwise) which arise out or in connection with the supply ofthe Goods or their use or resale by the Buyer, and the entireliability of the Seller under or in connection with the contractshall not exceed the Price, except as expressly provided inthese Conditions.

8.7 The Buyer acknowledges and accepts that it does notrely on, and shall have no remedy in respect of, any statement,representation, warranty or understanding (whether negligentlyor innocently made) of any person (whether party to theContract or not) other than as expressly set out in theseConditions as a warranty. Nothing in this clause shall,however, operate to limit or exclude any liability for fraud.

8.8 The Seller shall not be liable to the Buyer or be deemedto be in breach of the Contract by reason of any delay inperforming, or any failure to perform, any of the Seller’sobligations in relation to the Goods, if the delay or failure wasdue to any cause beyond the Seller’s reasonable control.Without prejudice to the generality of the foregoing, thefollowing shall be regarded as causes beyond the Seller’sreasonable control:

8.8.1 Act of God, explosion, flood, tempest, fire or accident;

8.8.2 war or threat or war, sabotage, insurrection, civildisturbance or requisition;

8.8.3 acts, restrictions, regulations, bye-laws, prohibitions ormeasures of any kind on the part of any governmental,parliamentary or local authority;

8.8.4 import or export regulations or embargoes;

8.8.5 strikes, lock-outs or other industrial actions or tradedisputes (whether involving employees of the Seller or of a thirdparty);

8.8.6 difficulties in obtaining raw material, labour, fuel, partsor machinery

8.8.7 power failure or breakdown in machinery or computerequipment;

8.8.8 failure of sub-contractors.

8.9 In the event that any of the circumstances referred to in8.8 continue for a continuous period of 30 days and iscontinuing at the end of that time to such an extent thatsubstantial performance of the contract is prevented theneither the Buyer or the Seller shall be entitled to give writtennotice terminating the contract with immediate effect. In theevent that the contract is so terminated, the Seller shall beentitled to be paid in full for all work completed to the date oftermination and a fair proportion for any work partiallycompleted.

8.10 The Seller shall endeavour to ensure that its businesssystems are year 2000 compliant but does not make anyrepresentations nor give any warranties in respect of suchcompliance. The Seller shall not be liable to the Buyer or bedeemed to be in breach of the Contract by reason of any delayin performing or any failure to perform any of the Seller’sobligations in relation to the delivery of the Goods, if the delayor failure arises from or is connected to the changes arisingbefore, during or after the year 2000

9. Insolvency of Buyer9.1 This clause applies if:

9.1.1 the Buyer makes any voluntary arrangement with itscreditors or (being an individual or firm) becomes bankrupt or(being a company) becomes subject to an administration orderor goes into liquidation (otherwise than for the purposes ofamalgamation or reconstruction); or

9.1.2 an encumbrancer takes possession, or a receiver isappointed, of any of the property or assets of the Buyer: or

9.1.3 the Buyer ceases, or threatens to cease, to carry onbusiness or (being a company) is wound up or dissolved (andno such step shall be taken by or on behalf of the Buyer withoutthe Seller being given at least 5 business days’ prior writtennotice thereof); or

9.1.4 steps are taken, proposed or threatened in respect ofany of the events mentioned above or the Seller reasonablyapprehends that any of the events mentioned above is about tooccur in relation to the Buyer and notifies the Buyeraccordingly.

9.2 If this clause applies then, without prejudice to any otherright or remedy available to the Seller, the Seller shall beentitled to cancel the Contract or suspend any furtherdeliveries under the Contact without liability to the Buyer, and ifthe Goods have been delivered but not paid for the Prices shallbecome immediately due and payable notwithstanding anyprevious agreement or arrangement to the contrary.

10. Export Terms10.1 Where the Goods are supplied for export from the UnitedKingdom, the provisions of this clause 11 shall (subject to anyspecial terms agreed in writing between the Buyer and theSeller) apply notwithstanding any other provision of theseConditions.

10.2 The Buyer shall be responsible for complying with anylegislation or regulations governing the importation of theGoods into the country of destination and for the payment ofany duties on them.

10.3 The Buyer shall be responsible for arranging for testingand inspection of the Goods at the Seller’s premises beforeshipment. The Seller shall have no liability for any claim inrespect of any defect in the Goods which would be apparent oninspection and which is made after shipment, or in respect ofany damage during transit.

10.4 Unless otherwise agreed in Writing between the Buyerand the Seller, the Goods shall be delivered FOB the air or seaport of shipment and the Seller shall be under no obligation togive notice under section 32(3) of the Sale of Goods Act 1979.

10.5 Any marine insurance required to be effect by the Sellerunder the Contract shall, unless otherwise agreed in writing, be10% over the invoice price and shall cover the interest from thecommencement of transit to the destination named in theContract as provided and contained in the Institute of LondonUnderwriters ("the Institute") Cargo Clauses, the Institute’s WarClauses and the Institute’s Strikes, Riots and Civil CommotionClauses, current at the time of shipment.

11. ECSC11.1 The Order must show the final destination of the Goodsand this destination may not be altered without the priorwritten consent of the Seller.

11.2 The goods are sold on the condition that they will not bere-sold by the Buyer or its buyers or sub-buyers for delivery inan unprocessed state outside the Territory of the ECSC. TheBuyer shall be responsible for any breach of this condition andthe Buyer shall also be responsible for ensuring that no goodssold to him by the Seller for delivery outside the ECSC shall bere-imported in an unprocessed state into the ECSC either bythe Buyer or any of its buyers or sub-buyers. On receipt of awritten demand from the Seller, the Buyer shall produceevidence of the ultimate destination of the Goods.

11.3 If the Buyer re-sells in an unprocessed state any goodsbought from the Seller then, unless such resale is made fromstock, the Buyer shall comply in respect of such resale with therequirement of High Authority Decision NO. 30/53 (as amendedfrom time to time) and also comply, as appropriate, with HighAuthority Decision No. 31/53 (as amended from time to time) orHigh Authority Decision No. 37/54 (as amended from time totime) and also comply with all other applicable requirementsfrom time to time of the High Authority or of the Europeancommission. The references in this Condition of the HighAuthority are to the High Authority of the ECSC constituted bythe Treaty of Paris of 18 April 1951.

12. General12.1 Any notice required or permitted to be given by eitherparty to the other under these Conditions shall be in Writingaddressed to that other party at its registered office or principalplace of business or such other address as may at the relevanttime have been notified pursuant to this provision to the partygiving notice.

12.2 No waiver by the Seller of any breach of the Contract bythe Buyer shall be considered as a waiver of any subsequentbreach of the same or any other provision.

12.3 If any provision of these Conditions is held by anycompetent authority to be invalid or unenforceable in whole orin part the validity of the other provisions of these conditionsand the remainder of the provision in question shall not beaffected.

12.4 The Contract shall be governed by the laws of England,and the Buyer agrees to submit to the exclusive jurisdiction ofthe English courts.

BRC Newhouse Block 14, Newhouse Industrial Estate, Newhouse, Motherwell ML1 5SETel: 01698 732343 Fax: 01698 833894Email: [email protected]

Scotland

www.brc.ltd.uk

BRC Darlington Skerne Works, Dodsworth Street, Albert Hill,Darlington, County Durham DL1 2NGTel: 01325 381166 Fax: 01325 284124Email: [email protected]

North East

VIR

CO-0

3.06

BRC OldhamGould Street, Oldham, Lancashire OL1 3LZTel: 0161 620 1001Fax: 0161 620 1660Email: [email protected]

North WestBRC BarnsleyWhaley Road, Barugh, Barnsley,South Yorkshire S75 1HTTel: 01226 730330Fax: 01226 771797Email: [email protected]

North

BRC Newport Corporation Road, Newport, Gwent NP19 4RDTel: 01633 280816Fax: 01633 283469Email: [email protected]

Wales & WestBRC Mansfield 79 Station Road, Sutton in Ashfield, Mansfield,Nottinghamshire NG17 5FRTel: 01623 555111Fax: 01623 440932Email: [email protected]

Midlands

BRC LondonUnit 13, Kierbeck Business Complex,North Woolwich Road, Silvertown, London E16 2BGTel: 020 7474 1800Fax: 020 7474 8686Email: [email protected]

South EastBRC SouthamptonBelbins Business Park, Cupernham Lane,Romsey, Hampshire SO51 7JFTel: 01794 521158Fax: 01794 521154Email: [email protected]

South

Finance officeBRC Plymouth Unit C, Kingsley Close, East Way, Lee Mill TradingEstate, Ivybridge, Plymouth, Devon PL21 9LLTel: 01752 894660Fax: 01752 896761Email: [email protected]

BRC Wokingham11 Mulberry Business Park, Fishponds Road,Wokingham, Berkshire RG41 2FHTel: 0118 977 3822Fax: 0118 977 3913Email: [email protected]

South West

BRC Special ProductsCarver Road, Astonfields Industrial Estate, Stafford ST16 3BPTel: 01785 222288Fax: 01785 240029Email: [email protected]: www.brc-special-products.co.uk

Weldgrip GeotechnicalUnit 19, Redbrook Business Park, Wilthorpe Road,Barnsley, South Yorkshire S75 1JNTel: 01226 280567Fax: 01226 731563Email: [email protected]: www.weldgrip.com

Other BRC companies

BRC Catalogue

Documents

Transcript of BRC Catalogue