Brake sistem Nissan
Transcript of Brake sistem Nissan
BRAKE SYSTEM DIAGNOSIS
1
STEP 2 CHA BRTN0202AJ
Diagnose & Repair Electronic Brake Systems
PERFORMANCE: • Be able to describe the basic electronic controlled brake system
outline for ABS, EBD, TCS and VDC. • Be able to describe the function of the electronic controlled brake
system. • Be able to diagnose the trouble diagnosis of the electronic controlled
brake system.
RESOURCES: The following resources have been prepared for this module.
• NISSAN vehicle • Digital multi-meter • CONSULT-ll • ESM
OBJECTIVE
CHA0038
BRAKE SYSTEM DIAGNOSIS
2
STEP 2 CHA BRTN0202AJ
• Perform inspection for the electronic brake system of a NISSAN vehicle within 30 minutes.
SKILL CHECK
BRAKE SYSTEM DIAGNOSIS
3
STEP 2 CHA BRTN0202AJ
CONTENTS
1. ELECTRONIC BRAKE CONTROL SYSTEM
OUTLINE
2. ABS (ANTI-LOCK BRAKE SYSTEM) 1) ABS Outline 2) ABS Operation
Here’s what you do . . . . (1)
3. EBD (ELECTRONIC BRAKE-FORCE DISTRIBUTION) 1) EBD Outline 2) EBD Operation
Here’s what you do . . . . (2)
4. TCS (TRACTION CONTROL SYSTEM) 1) TCS Outline 2) TCS Operation
Here’s what you do . . . . (3)
5. VDC (VEHICLE DYNAMICS CONTROL) 1) VDC Outline 2) VDC Operation
Here’s what you do . . . . (4)
6. SYSTEM COMPONENTS 1) System Layout 2) Wheel Rotation Sensor (Sensor and
Sensor Rotor) 3) Control Module 4) Yaw Rate/Side G-Sensor (Vehicle with
VDC) 5) G-sensor (Vehicle with 4WD) 6) Steering Angle Sensor (Vehicle with VDC) 7) VDC OFF Indicator Lamp (For vehicle with
VDC) 8) SLIP Indicator Lamp (For vehicle with VDC
and TCS) 9) ABS Warning Lamp
7. HYDRAULIC CIRCUIT
1) Component Parts and Functions of Oil Pressure Devices
TARGET
Ability to go to an ESM topic destination
Ability to read an ESM
Ability to describe the operation of the electronic brake control system
Ability to describe the operation of ABS
Ability to describe the operation of EBD
Ability to describe the operation of TCS
Ability to describe the operation of VDC
Ability to perform the trouble diagnosis of the electronic brake control system
BRAKE SYSTEM DIAGNOSIS
4
STEP 2 CHA BRTN0202AJ
CONTENTS 8. TROUBLE DIAGNOSIS WORK FLOW
1) Locate Malfunction Area 2) Confirm Precautions and For Correct and
Quick Diagnosis 3) Perform Preliminary Check 4) Confirmation of Warning Lamp and
Indicator Lamp 5) Confirmation of CONSULT-ll Display 6) When ABS is Not Displayed on the
CONSULT-ll Screen 7) Perform Self-Diagnosis 8) Check or Repair Malfunctioning Part 9) Erase the Self-Diagnosis Result 10) Perform Diagnostic Procedure for
Symptom 11) Confirm Symptom 12) Perform Self-Diagnosis Again
Here’s what you do . . . . (5) SKILL CHECK
TARGET
If you feel confident about your knowledge and skills of these tasks, you can proceed to the next module. Ask your course instructor for guidance.
BRAKE SYSTEM DIAGNOSIS
5
STEP 2 CHA BRTN0202AJ
1. ELECTRONIC BRAKE CONTROL SYSTEM OUTLINE
The electronic brake control system improves the driving stability by satisfying the braking performance, starting performance and turning performance at the same time. These performances can be obtained by each function of ABS, TCS, EBD and VDC. These systems are related to each other as shown in the figure below. You will study these systems to understand what kind of control is performed by each system.
2. ABS (ANTI-LOCK BRAKE SYSTEM)
1) ABS Outline The vehicle becomes unstable if the wheels lock when braking on a slippery road. Moreover, the braking distance will become longer. The ABS controls the braking force (wheel cylinder fluid pressure) electronically detecting wheel rotation while braking and avoids the locking of each wheel. Thus, the vehicle stability while fully braking and the turning performance while braking are increased. The ABS system consists of electronic and hydraulic units and components.
FUNCTION AND EFFECT OF ABS 1) To ensure the proper steering operation while braking 2) To be able to turn away from obstacles because the steering is secured 3) To ensure the vehicle stability by preventing flat spins
Watch a video to obtain technical information regarding the ABS function and effect.
Watch a video
CHA0039
TCS
ABS
EBD
VDC
BRAKE SYSTEM DIAGNOSIS
6
STEP 2 CHA BRTN0202AJ
CHA0040
Brake pressure
Slip
Vehicle speed
Vehicle stops
Speed of wheels
Bra
ke p
ress
ure
Spe
edWheels are locked
Time
2) ABS Operation
ABS is designed to control brake fluid pressure so that the wheels are prevented from locking during abrupt braking. More specifically, adequate control of brake fluid pressure maintains the optimum “slip” ratio between the wheels and road surface, thus stopping the vehicle firmly and quickly.
When full braking is applied, the wheel speed becomes lower than the vehicle speed resulting in slippage between the tires and road surface. The amount of slippage is shown as the red shaded area in the figure on the right. The ABS controls the brake fluid pressure to minimize the slippage in order to prevent the vehicle from losing driving control due to wheel locking. This slippage is called the slip ratio. Slip ratio= (Vehicle speed – Wheel speed) /Vehicle speed The slip ratio is controlled by the ABS to maintain the optimum condition (0.15 - 0.30).
The maximum braking performance can be obtained when the slip ratio is controlled to be around these figures.
The operation of the ABS is explained in the e-Learning program provided here.
e-Learning
Here’s what you do . . . . (1)
What are the three functions and effects of the ABS? 1) 2) 3)
Self-check
BRAKE SYSTEM DIAGNOSIS
7
STEP 2 CHA BRTN0202AJ
CHA0041
Front brake force Rear brake force
Front brake force Rear brake force(same as 1.)
Front brake force Rear brake force(larger than 1.)
EBD effectiveness (same braking force)
1. Light load
2. Heavy load(without EBD)
3. Heavy load(with EBD)
CHA0042
Ideal braking force distribution: loaded
EDB braking force
Current type (P-value)
Ideal braking force distribution: unloaded
Bra
king
forc
e of
rear
whe
el
3. EBD (ELECTRONIC BRAKE-FORCE DISTRIBUTION)
1) EBD Outline
EBD is adopted into the ABS system in order to keep the brake performance stable (regardless of the loading condition of the vehicle). Its function is to control the braking force distribution to the front and rear electrically according to the loading condition. When the load distribution on rear wheel side increases, it divides brake force ideally according to the skid ratio difference of the tires between the front and rear. A load sensing valve (LSV) and a proportioning valve (P-valve) control the fluid pressure of the rear brake mechanically. Instead of these systems, EBD logic is built into the ABS system, and it operates the brake force ideally.
The load sensing valve (LSV) mechanically controls the rear brake force depending on the weight of the load. EBD works the same as LSV operation, but it does not sense the load on the vehicle. EBD monitors the front and rear wheel skid ratio by using ABS components. The EBD does not have any components, but its logic is built into the ABS system. The rear brake force is controlled on demand electrically and ideally. As a result, the system provides better brake effect for any vehicle weight.
BRAKE SYSTEM DIAGNOSIS
8
STEP 2 CHA BRTN0202AJ
CHA0043
ABS valve operation
Inlet valve
Outlet valveOFF
OFF
OFF
OFFOFF OFF
ON ON
EBD control threshold
Rear wheel speed
Front wheel speed
Vehicle speed
ABS control threshold
Spe
ed
Time
Front wheel fluid pressure
Rear wheel fluid pressure
EBD controlABS control
Flu
id p
ress
ure
Time
2) EBD Operation The EBD monitors the difference of front wheel skid and rear wheel skid. When the difference becomes greater than a certain specification, EBD holds the rear brake fluid pressure to increase in order to make the front and rear wheel skid become equal. And after the difference is returned to the specification, EBD allows for increasing the rear brake fluid pressure again. The figure on the right shows how EBD works and ABS valve operates. When the difference of the front wheel skid and rear wheel's one exceeds EBD control threshold, the inlet valve of ABS will close and hold the brake pressure that applies. After the difference is returned into the EBD control threshold, the inlet valve of ABS opens and allows the fluid pressure to apply to the rear wheel cylinder.
The operation of the EBD is explained in the e-Learning program provided here.
e-Learning
Here’s what you do . . . . (2)
Describe the function of the EBD briefly.
Self-check
BRAKE SYSTEM DIAGNOSIS
9
STEP 2 CHA BRTN0202AJ
CHA0044
(2) Rear wheel speed
(1) Front wheel speed
(4) Secondary throttle opening
(3) Throttle openinig
(5) Rear brake pressureTCS OFFTCS ON
TCS OFFTCS ON
TCS OFFTCS ON
Wheel speed
Throttleopeningangle
Rear brakepressure
0
0
100%
Time
Time
Time
0%
TCS ON thresholdTCS OFFthreshold
4. TCS (TRACTION CONTROL SYSTEM)
1) TCS Outline On a road surface that is easy to cause slippage, a decrease in driving stability due to tail spin or unsatisfactory acceleration due to driving wheel spin occurs when starting or during sudden acceleration. The TCS controls the engine torque and brake force of the driving wheels using the various devices that are electronically controlled. As a result, the TCS prevents the driving wheels from spinning to increase the starting and acceleration performance and the driving stability and safety. 2) TCS Operation 1. Taking the average speed of the front
wheels as a base (1), the wheel speed of the rear (driving) wheels (2) is continuously monitored and compared.
2. The driver opens the throttle (3) and the speed of the rear wheels increases as a result. When the wheel speed exceeds the preset TCS ON threshold, the TCS turns itself ON. The secondary throttle (4) closes as the rear brake oil pressure is increased (5).
3. When the rear wheel speed decreases to a level between the thresholds of TCS ON and TCS OFF, the throttle position and the brake oil pressure level are maintained.
4. Finally, when the rear wheel speed drops below the TCS OFF threshold, the system switches itself OFF, opening the throttle and decreasing the brake oil pressure.
5. Until all tendencies have completely disappeared, steps 2 through 4 are repeated. The TCS function is explained in the e-Learning program provided here.
e-Learning
Here’s what you do . . . . (3)
Describe the function of the TCS briefly.
Self-check
BRAKE SYSTEM DIAGNOSIS
10
STEP 2 CHA BRTN0202AJ
5. VDC (VEHICLE DYNAMICS CONTROL)
1) VDC Outline The VDC automatically improves the driving stability by controlling the braking force of the four wheels respectively and the engine output while avoiding obstacles. The system is operated by the controlling function according to the deviation of the calculated side skid from the target while steering. 2) VDC Operation The control unit calculates the actual status of the vehicle during cornering based on the steering angle, yaw rate, deceleration, vehicle speed, etc. If the vehicle is in the oversteer/understeer status, VDC applies the brake force to the 4 wheels respectively to prevent these statuses. The VDC function is explained in the e-Learning program provided here.
e-Learning
CHA0045
Fuel cutsignal
Throttle control signal
CAN communication line
Electrical controlledthrottle
Front RH wheel sensor
Rear RH wheel sensor
: Electrical circuit: Fluid pressure circuit
Rear LH wheel sensor
Master cylinder
Pressure sensorActuator drive signal
VDC/TCS/ABC actuator
Yaw rate/side G-sensor
Front LH wheel sensor
Steeringanglesensor
A/T C/UECCS C/U Combination meter
VDC/TCS/ABS C/U
BRAKE SYSTEM DIAGNOSIS
11
STEP 2 CHA BRTN0202AJ
Oversteer:
The rear tires produce too much cornering force, and the vehicle has the tendency to go to the inside of the curve.
Understeer:
The front tires do not produce enough cornering force, and the vehicle has the tendency to go to the outside of the curve.
Slip angle:
The angle between the direction in which a tire is aimed or steered and the actual direction of tire travel.
Yaw :
The rotation force of the vehicle’s body around its center point as viewed from above.
CHA0046
Slip angle
Direction of wheel
Actual
BRAKE SYSTEM DIAGNOSIS
12
STEP 2 CHA BRTN0202AJ
CHA0058
Yaw rate signalLateral acceleration signalAcceleration/Deceleration signal
Steering angle signal
Calculating target slip angleCalculating actual slip angle
Controlling brake force Controlling engine torque
Comparing the actual and the targetCalculating the compensation level
CHA0047
Oversteer
Slip angle
time
time
time0
0
0
Front RH wheelbrake force
Engine torquereduction
Actual slip angle
Target slip angle
OUTLINE OF OPERATION FLOW VDC compares the actual slip angle of the vehicle and the target slip angle that is calculated by the control unit based on the steering angle signal and brake pressure signal that are controlled by the driver. Then, it controls the brake force and engine output torque to obtain the target slip angle.
The figure on the right shows the VDC operation. The situation is: A vehicle is in oversteer during a left turn while accelerating. When the actual slip angle deviates from the target value, the system applies the brake force and reduces the engine output torque.
BRAKE SYSTEM DIAGNOSIS
13
STEP 2 CHA BRTN0202AJ
Here’s what you do . . . . (4)
Describe the function of the VDC briefly.
Self-check
BRAKE SYSTEM DIAGNOSIS
14
STEP 2 CHA BRTN0202AJ
CHA0048
13. Yaw rate/side G-sensor*
1. Front RH wheel sensor rotor
4. Front LH wheel sensor rotor
7. Rear RH wheel sensor rotor
10. Rear LH wheel sensor rotor
2. Front RH wheel sensor
5. Brake booster and master cylinder
8. Rear RH wheel sensor
11. Combination meter (Brake warning lamp, ABS warning lamp, VDC OFF indicator lamp, SLIP indicator lamp)
3. Front LH wheel sensor
6. ABS actuator and electric unit (control unit)
9. Rear LH wheel sensor
12. VDC OFF switch
16. Electric throttle control actuator
19. Transaxle assembly
14. Steering angle sensor
17. Engine
15. Throttle control signal
18. ECM
20. TCM
6. SYSTEM COMPONENTS
1) System Layout
Numbers in the illustration with display additional information when they are clicked. : Component parts in the shaded area in the figure above are common to ABS, EBD, TCS and
VDC. *The G-sensor is used for the ABS system of vehicles with 4WD.
BRAKE SYSTEM DIAGNOSIS
15
STEP 2 CHA BRTN0202AJ
CHA0056
Sensor
Knuckle
Front wheel sensor
Sensor housing(The sensorrotor is inte-grated into thebearing.)
2) Wheel Rotation Sensor (Sensor and Sensor Rotor) The sensor detects the rotational speed of each wheel and sends it to the control unit.
ACTIVE SENSOR (MAGNET ENCODER TYPE J31, V35, C11, K12, ETC.) • With IC in the detector and magnetized
sensor rotor, downsizing and weight reduction are promoted.
• Power is supplied to the detector circuit to read out magnetic flux. Magnetic force is detected electrically, and it is and converted to a current signal.
• As the sensor rotor rotates, the magnetic field changes. Changes in the magnetic field are converted to current signals (square wave signal). Signals are sent to the ABS control unit. Changes in the magnetic field are proportional to the wheel rotation speed.
The circuit in the wheel rotation sensor of an active sensor type may be damaged if a multi-tester is used to measure the resistance. Use CONSULT-ll for examination to check whether the sensor is OK or NG.
CHA0057
Line of magnetic force
Magnetic rotorN
N
N
N
S
S
S
S
Sensor Amplification circuit
S N S N S N
Control unit
Sensor
Magnetic
Magneticencoder
flux
IC
SIG
V+
14mA
7mA
BRAKE SYSTEM DIAGNOSIS
16
STEP 2 CHA BRTN0202AJ
CHA0059
Sensor
Sensor rotor
Moving time of one tooth
Magnet
Magnetic flux
Tooth
V : Induced electromotive force
V
V
Control unit
Low carbon steet
Coil
CHA0060
ABS actuator and electric unit (control unit)
PASSIVE SENSOR (N16, A33, ETC.) The sensor unit consists of a gear-shaped sensor rotor and a sensor element. The element contains a bar magnet around which a coil is wound. The sensor is installed on the back side of the brake rotor. Sine wave current is generated by the sensor as the wheel rotates. The frequency and voltage increase(s) as the rotating speed increases.
Use the AC range to measure the sensor output.
3) Control Module The ABS actuator and control unit are integrated. The vehicle with VDC/TCS/ABS controls each function of VDC/TCS/ABS synthetically. The vehicle with the EBD function is equipped with the built-in EBD control function. The control unit receives a signal sent from each wheel speed sensor, computes wheel speed, etc. and sends a signal to the actuator which controls (decreases, increases and maintains) the brake fluid pressure in the wheel cylinders so that the wheels do not lock. 4) Yaw rate/side G-sensor (Vehicle with VDC) The sensor detects the yaw rate/lateral G/longitudinal G of the vehicle and sends the analog voltage signal to the ABS actuator control unit.
CHA0061
Yaw rate/sideG-sensor
BRAKE SYSTEM DIAGNOSIS
17
STEP 2 CHA BRTN0202AJ
5) G-sensor (Vehicle with 4WD) The G-sensor senses deceleration during braking to determine whether the vehicle is being driven on a high µ* road (asphalt road, etc.) or a low µ* road (snow-covered road, etc.). It then sends a signal to the ABS control unit. µ* (mju:): Symbol that stands for the friction coefficient. The reed switch turns on when it is affected by a magnetic field. During sudden deceleration (braking on a high µ road), the weight moves and the magnet in the weight moves away from the reed switch. The magnetic field then diminishes, and the reed switch turns OFF.
CHA0062
Braking (high road surface) Braking (low road surface)and Normal position.
Reed switch
G-sensor
Magnet Weight
Front
Under the driver's seat
Front
ONOFF
BRAKE SYSTEM DIAGNOSIS
18
STEP 2 CHA BRTN0202AJ
CHA0064
CHA0065
CHA0063
Steering angle sensorScrew
Spiral cableSteering anglesensor connector
BACK OF SPIRAL CABLE ASSEMBLY
6) Steering Angle Sensor (Vehicle with VDC) The sensor detects rotation, angular velocity and turning direction of the steering wheel and sends the signals to ABS actuator control unit through CAN communication. 7) VDC OFF Indicator Lamp (For vehicle with VDC) The lamp turns ON when a malfunction occurs in the electric system of EBD and VDC/TCS/ABS. It also turns ON when the VDC/TCS function is arbitrarily canceled. When the ignition switch is turned ON for the lamp check, the lamp turns ON for about one second and then turns OFF.
8) SLIP Indicator Lamp (For vehicle with VDC and TCS) The lamp turns ON when a malfunction occurs in electric system of EBD and VDC/TCS/ABS. It turns ON when the VDC or TCS function operates. When the ignition switch is turned ON for the lamp check, the lamp turns ON for about one second and then turns OFF.
BRAKE SYSTEM DIAGNOSIS
19
STEP 2 CHA BRTN0202AJ
CHA0066
CHA0067
ABS actuator and electric unit (control unit)
Master cylinder
Primary side Secondary side
Pump
Outlet valve
Outlet solenoid valve
Outlet solenoid valve
Outlet solenoid valve
Outlet solenoid valve
Returncheck valve
Returncheck valve
Returncheck valve
Returncheck valve
Inlet solenoid valve Inlet
solenoid valve
Inlet solenoid valve
Inlet valve
Inlet valve
Motor
Reservoir Reservoir
Front RHcaliper
Rear LHcaliper
Front LHcaliper
Rear RHcaliper
Inlet solenoid valve
9) ABS Warning Lamp When a malfunction occurs in the electrical system, the lamp turns ON and warns that the brake system is in the fail-safe mode and the conventional brake system is in operation. The system is functioning normally if the lamp turns ON and then turns OFF after one second when the ignition switch is turned ON. The ABS warning lamp and the brake warning lamp turn ON at the same time when a malfunction occurs in the EBD system.
7. HYDRAULIC CIRCUIT
HYDRAULIC CIRCUIT DIAGRAM
BRAKE SYSTEM DIAGNOSIS
20
STEP 2 CHA BRTN0202AJ
1) Component Parts and Functions of Oil Pressure Devices
Components Contents Solenoid valve (ABS control valve)
The solenoid valve increases, maintains or decreases hydraulic pressure in each wheel cylinder according to the signal from the ABS actuator control unit.
Reservoir The reservoir temporarily reserves the brake fluid pulled out from wheel cylinders to perform decompression of wheel cylinders effectively.
Pump The pump returns the brake fluid reserved in the reservoir by decompression to the master cylinder.
Motor The motor drives the pump according to the signal from the ABS actuator control unit.
Inlet valve (pressure increasing)
The inlet valve stops the sucked brake fluid from the reservoir to the pump from returning to the reservoir again.
Outlet valve (pressure decreasing)
The outlet valve stops the brake fluid discharged from the pump from returning to the pump again.
Return check valve The return check valve returns the brake fluid in the wheel cylinder to the master cylinder bypassing the orifice of the solenoid valve when the brake is released.
Damper room The damper room damps pulsation of the brake fluid and reduces vibration of the pedal when VDC/TCS/ABS is in operation.
Cut valve The cut valve blocks the fluid route from the master cylinder for the conventional brake system when VDC/TCS is in operation.
Suction valve The suction valve supplies the brake fluid from the master cylinder to the pump when VDC/TCS is in operation.
Obtaining technical information regarding the fluid circuit operation is explained in the e-Learning program provided here.
e-Learning
BRAKE SYSTEM DIAGNOSIS
21
STEP 2 CHA BRTN0202AJ
8. TROUBLE DIAGNOSIS WORK FLOW
Perform diagnosis referring to the flowchart described in the ESM in case a malfunction occurs in the electronic brake control systems.
CHA0068Inspection end.
Inspection start.Locate trouble area (using diagnostic worksheet).
Confirm “PRECAUTIONS” and “For Correct andQuick Diagnosis”.
Perform PRELIMINARY CHECK.
Do (Does) ABS warning lamp, brakewarning lamp, SLIP indicator lamp orVDC OFF indicator lamp light?
Erase self-diagnotic results, then drive the vehicle for more than one minute at 30 km/h (19 MPH) or more. Perform self-diagnostic.
Perform self-diagnostic again.
Check harness connector betweenABS actuator and electric unit (controlunit) and data link connector.
Perform diagnostic procedure forsymptom.
Confirm symptom.
Does “ABS” appear on CONSULT-II display?
Perform self-diagnostic.
Check or repair malfunctioning part.
Yes
Yes
OK OK
NGNG
NONO
1)
2)
3)
4)
9)
12)
6)
10)
11)
5)
7)
8)
BRAKE SYSTEM DIAGNOSIS
22
STEP 2 CHA BRTN0202AJ
CHA0069
Customer name MR/MS
Engine #
Incident Date
Symptoms
Engine conditions
Road conditions
Driving conditions
Applying brake conditions
Other conditions
Model & Year
Trans.
Manuf. Date
VDC/TCS does not work(Drive wheels slip whenaccelerating, etc.)
VIN
Mileage
In Service Date
Warning / Indicatoractivate
ABS does not work.(wheels slip whenbraking)
Firm pedal operationLarge stroke pedaloperation
Lack of sense of acceleration
When starting After starting
Low friction road ( Snow Gravel Other )
Bumps / potholes
Full-accelerationHigh speed corneringVehicle speed: Greater than 10 km/h (6 MPH)Vehicle speed: 10 km/h (6 MPH) or lessVehicle is stopped
Suddenly
Gradually
Operation of electrical equipment
Shift change
Other descriptions
Noise and vibration(from engine compartment)Noise and vibration(from axle)
TROUBLE DIAGNOSIS
ASKING COMPLAINTS
• Complaints vary depending on the person. It is important to clar- ify the customer's actual remarks. WHAT
KEY POINTS
Vehicle model
• Ask the customer about what symptoms are present and under what conditions. Use the information to reproduce the symptom while driving.• It is also important to use diagnosis sheet so as not to miss vital information.
[VDC/TCS/ABS]
......
WHEN Date, Frequencies......
WHERE Road conditions......
HOW Operating conditions,Weather conditions,Symptoms
......
1) Locate Malfunction Area Obtain detailed information from the customer to clarify the incident using the DIAGNOSIS SHEET described in the ESM.
BRAKE SYSTEM DIAGNOSIS
23
STEP 2 CHA BRTN0202AJ
2) Confirm Precautions and For Correct and Quick Diagnosis Check the items below before performing trouble diagnosis. Be careful that the customers do not misunderstand a normal operation to be an incident. 1. Motor operating sound During ABS operation, brake pedal lightly vibrates and
a mechanical noise may be heard. This is normal. 2. Sound of system operation
check Just after starting vehicle after ignition switch is turned ON, the brake pedal may vibrate or motor operating noise may be heard from the engine compartment. This is a normal status of the operation check.
3. Braking distance of ABS Stopping distance may be longer than that of vehicles without ABS when vehicle drives on rough, gravel, or snow-covered (fresh, deep snow) roads.
4. Improper tire size Improper brake pads
If the tire size and type are used in an improper combination, or brake pads are not Genuine NISSAN parts, the stopping distance or steering stability may deteriorate.
5. During sudden acceleration or abrupt steering
When the TCS or VDC is activated by sudden acceleration or a sudden turn, some noise may occur. The noise is a result of the normal operation of the TCS and VDC.
6. Driving on steep hill or bank When driving on roads that have extreme slopes (such as mountainous roads) or high banks (such as sharp curves on a freeway), the VDC may not operate normally, or the VDC OFF indicator lamp and the SLIP indicator lamp may turn ON. However, this is not a problem if normal operation can be resumed after restarting the engine.
It is important to obtain detailed information about the occurrence of the incident at the time of reception because it may be resolved by an explanation of the items above. 3) Perform Preliminary Check 1) Check the quantity of brake fluid, brake fluid leakage and brake pads. 2) Check loosening of electric terminal and battery. 3) Check ABS warning lamp, brake warning lamp, VDC OFF indicator and SLIP indicator.
Check the items above.
See the ESM for the actual description
BRAKE SYSTEM DIAGNOSIS
24
STEP 2 CHA BRTN0202AJ
CHA0070
Condition
Ignition switch OFF
EBD error
Soon after ignition switch isturned ON
When VDC/TCS is not func-tioning normally.
Soon after ignition switch isturned ON(System normal)
When the VDC OFF switchis turned ON. (VDC functionOFF)
VDC/TCS/ABSerror
ABS warninglamp
Brake warninglamp (Note 2)
VDC OFF indica-tor lamp
SLIP indica-tor lamp
(Note 1)
(Note 1)
Remarks
Goes out 2 secondsafter ignition switch is
turned ON.
There is an ABS actu-ator and electric unit
(control unit)error. (power groundor system malfunc-
tion)
Note 1 : Turns off after engine start.Note 2 : The brake warning lamp turns on during parking brake operation (when switch is on) and brake fluidlevel sensor operation (insufficient brake fluid).
: ON : OFF
4) Confirmation of Warning Lamp and Indicator Lamp Confirm the lighting status change of the warning lamp and indicator lamp according to the system malfunction.
5) Confirmation of CONSULT-Ⅱ Display Confirm that ABS is displayed on the CONSULT-ll screen. 6) When ABS is Not Displayed on the CONSULT-ll Screen Check the wiring of the ABS control module and CAN communication line, etc. when ABS is not displayed on the CONSULT-ll screen. 7) Perform Self-Diagnosis Perform self-diagnosis with CONSULT-ll. (Refer to the link for the method of diagnosis without CONSULT-ll.) 8) Check or Repair Malfunctioning Part Referring to ESM, check and repair the malfunctioning parts.
BRAKE SYSTEM DIAGNOSIS
25
STEP 2 CHA BRTN0202AJ
CHA0071
Symptom 4 : ABS does not workCAUTION:
ABS does not operate when the vehicle speed is 10 km/h (6 MPH) or lower.
Make sure that the warning lamp turns off approximately 2 seconds after the key switch is turned on or whendriving.
1. CHECK ABS WARNING LAMP DISPLAY
OK or NG
OK >> GO TO 3. Vehicle Speed Sensor Inspection in BRC -98 “Symptom 1 : Excessive ABS Function Operation Frequently”
NG >> Perform self-diagnosis. Refer to BRC-71. “SELF-DIAGNOSIS” (With CONSULT-ll). BBC-79. “On Board Self-Diagnosis” (Without CONSULT-ll).
9) Erase the Self-Diagnosis Result When the repair is completed, erase the self-diagnosis result and perform self-diagnosis again after running for more than 1 minute at a speed of 30 km/h or higher. 10) Perform Diagnostic Procedure for Symptom If the warning lamp is not turned ON, check and repair the detected malfunctioning system using the symptom matrix chart described in the ESM. 11) Confirm Symptom Confirm that the malfunction is not occurring again. 12) Perform Self-Diagnosis Again
Perform the final self-diagnosis and confirm that there is no malfunction.
BRAKE SYSTEM DIAGNOSIS
26
STEP 2 CHA BRTN0202AJ
Here’s what you do . . . . (5)
There is a malfunctioning vehicle whose ABS warning lamp is ON and the ABS does not operate. Perform trouble diagnosis by referring to TROUBLE DIAGNOSIS WORK FLOW described in the ESM. 1) Which warning lamp is ON?
2) Write down the self-diagnosis result.
3) Check the malfunctioning part indicated by the self-diagnosis result. What kind of malfunction is it?
Self-check
At this point, if you feel confident about your knowledge and skills of these tasks, you can proceed to the next page for the skill check for this module.
BRAKE SYSTEM DIAGNOSIS
27
STEP 2 CHA BRTN0202AJ
Diagnose & Repair Electronic Brake Systems
• Use an actual NISSAN vehicle and perform the following skill check.
• Your course instructor will inform you about the location of the workstation and how you will perform this skill check.
• Complete the skill check within 30 minutes. Tell your course instructor when you are ready to start. Your course instructor will time you accordingly.
There is an incident in the brake control system on this vehicle. Diagnose and repair the incident and pinpont the location on the wiring diagram provided by your course instructor. The time limit is 30 minutes.
1. What is malfunctioning?
2. Write the items what you checked. For each item, diagnose and judge the result OK or NG.
What did you check? Result Judgement
1 OK / NG 2 OK / NG 3 OK / NG 4 OK / NG 5 OK / NG 6 OK / NG
3. What is the reason for your answer to the above question? Reason:
SKILL CHECK
BRAKE SYSTEM DIAGNOSIS
28
STEP 2 CHA BRTN0202AJ
COURSE INSTRUCTOR’S SIGNATURE
Signature:
Name:
Date: / /
Technician
Name:
Number:
Company:
Sign-off