Bracket Assembly and Installation Manual POA-CHB … · (Used together with POA-CHS-PS02 and...
Transcript of Bracket Assembly and Installation Manual POA-CHB … · (Used together with POA-CHS-PS02 and...
Be sure to consult with a qualifiedinstallation specialist.
This bracket is only for use with Sanyo projectors. Do not use for any other equipment or purposes. Be especially careful that children do not hang from it. Perform proper assembly and installation by following these instructions. Be sure to follow all precautions.
BracketAssembly andInstallation Manual
Model POA-CHB-DWL2500
■ Installation Precautions
The diagram shows the ceiling bracket for low ceilings by way of example.
✽ This product is used together with the products listed below. It cannot be used together with any products other than those listed below.
●POA-CH-EX03A (Wall hanging bracket)+POA-CHS-PS02 (Low-ceiling Bracket) ●POA-CHS-PS02 (Low-ceiling Bracket) ●POA-CHL-PL02 (High-ceiling Bracket)
Contents
Installation Precautions ------------------------- 1
-------------------------------------------- 2Parts list
Attach the Projector bracketto the projector ------------------------------------ 2
------------------------------------- 4
------------------------------------ 3
Attach the projector to theceiling bracket
Attach the drop-prevention wireto the projector
---------------------------------------- 6
How to adjust the projection angle
Dimensions
----------- 7-8Approximate projection distance
----------- 5
When hanging a projector from the ceiling using this bracket (hereinafter called “the projector bracket”), the ceiling must have adequate strength to support the projector, the ceiling bracket and the projector bracket. Furthermore, if installing to a wall, the wall must have enough strength to support the combined weight of the projector, the wall mount bracket, the ceiling mount bracket and this projector bracket.Before installation, check the combined weight of the projector, ceiling mount bracket and wall mount bracket (if installing to a wall) and this projector bracket as well as the strength of the ceiling or wall based on that weight. If the strength is insufficient, provide adequate reinforcement before proceeding.
●Always install to a level ceiling. Never install to an inclined ceiling.●During installation, take appropriate measures to prevent lateral swaying due to earthquakes or
vibration (using wires, etc.).
The total weight of the projector bracket is 4.0 kg.
2
Projector bracket......1
Drop-prevention wires...2 Assembly and InstallationManual (this manual)
Fastening plates......2
Turn over the projector and use the included Screws B (x5) to attach the Projector bracket.
■ Attach the Projector bracket to the Projector
Screws D......4M3 x 8mm(Phillips head machine screw with integrated spring washer)
Screws B......5M4 x 18mm(Phillips head machine screw with integrated spring washer and flat washer)
Screws A......4M4 x 10mm(Phillips head machine screw with integrated spring washer and flat washer)
Screws C......4M6 x 14mm(Phillips head hex bolt with integrated spring washer and flat washer)
■ Parts list
Projector bracket
Screws B (included) ... 5
3
2. Wind the drop-prevention wire around the adjuster two more times.
2. Wind the drop-prevention wire around the bar one more time.
3. Attach the drop-prevention wire to the projector bracket with the two included screws A, and then lower the adjuster.
3. Attach the drop-prevention wire to the projector bracket with the two included screws A.
1. Lift up the adjuster of the projector, and then wind the included drop-prevention wire around it as shown in the illustration.
1. Wind the included drop-prevention wire around the theft-prevention wire installation bar as shown in the illustration.
Installing to the adjustersq Installing to the theft-prevention wire installation barw
To prevent the projector from falling down, use the included drop-prevention wires to connect the projector and the projector mount bracket. (2 locations)
■ Attach the drop-prevention wire to the Projector
Preventing the projector from falling:✽Be sure to follow these instructions to keep
the projector from falling.
Adjuster
Drop-prevention wire (included)
Screws A (included) ... 2
Screws A (included) ... 2
Drop-prevention wire (included)
Theft-prevention wireinstallation bar
Wind around two more times.
Theft-prevention wireinstallation bar
Adjusterq
w
Wind around one more time.
w Use the included Screws C (x4), fastening plates, Screws D (x4) to secure the projector bracket to the ceiling bracket✽ (sold separately).
4
■ Attach the projector to the ceiling bracket✽
q Install by sliding the projector bracket with the projector installed into the ceiling mount bracket✽
(sold separately) which is secured to the ceiling or to the wall mount bracket (sold separately).
Be careful not to drop the projector while this process. Although the projector is supported, it is not secured in place.
Ceiling bracket✽
Projector bracket
Screws D (included) ... 2
Screws D (included) ... 2
Screws C (included) ... 2
Screws C (included) ... 2
✽High-ceiling Bracket : POA-CHL-PL02Low-ceiling Bracket : POA-CHS-PS02The diagram shows the low-ceiling bracket by way of example.
Fastening plates(included)
Fastening plates(included)
5
Loosen the angle adjustment nut using the wrench included with the ceiling bracket✽ (sold separately) and align the projector to project the image in the center of the screen. Then fasten the nut securely.
Before adjusting: • Read the projector instruction manual carefully, turn on the power, and project an image. • Loosen the slide mechanism fixing screws, and then move the ceiling mount bracket forward or
back to provisionally determine the projection size. Then retighten the slide mechanism fixing screws and adjust the angle.
Slides forward and back 170 mm
After securing the projector angle, if the angle is readjusted without loosening the screw, the fastening area could be deformed, which could prevent it from being tightened again. When readjusting the angle, loosen the angle adjustment nut before adjusting the angle.If the adjustment is off center, readjust the angle.
Caution
After making the adjustment, be sure the screw is securely tightened.
■ How to adjust the projection angle
✽High-ceiling Bracket : POA-CHL-PL02Low-ceiling Bracket : POA-CHS-PS02The diagram shows the low-ceiling bracket by way of example.
Angle adjustment nut
Turns left and right 360°
Slide mechanism fixing screws
Slide mechanism fixing screws
15° horizontal tilt
15° horizontal tilt
WrenchIf using a commercially-available wrench, use one with a size of 24mm.
(Unit: mm)
(Unit: mm)
(Unit: mm)
6
(Used together with POA-CH-EX03A, POA-CHS-PS02 and POA-CHB-DWL2500)
(Used together with POA-CHS-PS02 and POA-CHB-DWL2500)
When using the wall hanging bracket
When using the low-ceiling bracket
(Used together with POA-CHL-PL02 and POA-CHB-DWL2500)A length shows distance from ceiling to lower side of projector when suspended from ceiling.
When using the high-ceiling bracket
■ Dimensions
160.5160.5
77.5
77.5
177209
374.
3-40
0.1
(Hei
ght a
djus
tabl
e)
386
160.5 160.5209
77.5
177386
352.
3A
leng
th
209160.5 160.5
177386
Center of lens
Center of lens
Center of lens
Min
A length
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
1071.3
1101.3
1131.3
1161.3
1191.3
1221.3
1251.3
1281.3
1311.3
1341.3
1371.3
1401.3
1431.3
1461.3
1491.3
1521.3
1551.3
1581.3
1611.3
1641.3
(Unit: mm)
(Unit: mm)
(Used together with POA-CHS-PS02 and POA-CHB-DWL2500)When using the low-ceiling bracket
(Used together with POA-CHL-PL02 and POA-CHB-DWL2500)When using the high-ceiling bracket
7
X(mm)
A le
ngth
233
Y(m
m)
209 177
386
Sliding width170mm
Y(m
m)
233X(mm)
209 177
386
Sliding width170mm
PDG-DXL2000
PDG-DWL2500Screen size X(mm) Y(mm)
80”(16:10)90”(16:10)
100”(16:10)110”(16:10)
2469
114159
A length+87A length+107A length+127A length+147
Screen size X(mm) Y(mm)70”(4:3)80”(4:3)90”(4:3)
3488
141
A length+115A length+141A length+168
PDG-DXL2000
PDG-DWL2500Screen size X(mm) Y(mm)
80”(16:10)90”(16:10)
100”(16:10)110”(16:10)
2469
114159
439.3459.3479.3499.3
Screen size X(mm) Y(mm)70”(4:3)80”(4:3)90”(4:3)
3488
141
467.3493.3520.3
* Height values are intended as a guide only. The screen sizes may vary depending on the content of the projected images, so use the slide mechanism to adjust the position.
Slide mechanism fixing screws
Slide mechanism fixing screws
■ Approximate projection distance (1) (When using projector: PDG-DWL2500 or PDG-DXL2000)
8
(Unit: mm)
(Used together with POA-CH-EX03A, POA-CHS-PS02 and POA-CHB-DWL2500)When using the wall hanging bracket
Check that the slide mechanism fixing screws are fully tightened even when not using the sliding mechanism.
Y(m
m)
X(mm)
386
177209
Sliding width170mm
374.
3(W
hen
heig
ht a
djus
ted
to th
e m
inim
um)
PDG-DXL2000
PDG-DWL2500Screen size X(mm) Y(mm)
80”(16:10)90”(16:10)
100”(16:10)110”(16:10)
2469
114159
461.3-481.3-501.3-521.3-
Screen size X(mm) Y(mm)70”(4:3)80”(4:3)90”(4:3)
3488
141
489.3-515.3-542.3-
Slide mechanism fixing screws
* Distance Y can be adjusted to a height of 25.8 mm with the POA-CH-EX03A (sold separately).Refer to the assembly and installation manual for the POA-CH-EX03A (sold separately) for details on the adjustment method.
* Height values are intended as a guide only. The screen sizes may vary depending on the content of the projected images, so use the slide mechanism to adjust the position.
■ Approximate projection distance (2) (When using projector: PDG-DWL2500 or PDG-DXL2000)
Caution