BPD14302 CONSTRUCTION DRAWING
Transcript of BPD14302 CONSTRUCTION DRAWING
BPD14302CONSTRUCTION DRAWING
INTRODUCTION TO CONSTRUCTION DRAWING
LEARNING OUTCOME
• At the end of this chapter students will be able to:-• Use the drawing tools.• Draw title block, lettering and dimension.
CONTENTS
o Introductiono Variety of Drawing Tools Applicationo Preparation of Drawing Paper and Title
Blocko Lettering, Dimension and Working Lineso Engineering Drawing, Architectural Drawing, Mechanical and
Electrical Drawingo Conclusiono Lab work 1
INTRODUCTION
o This topic discuss on introduction of variety of drawing tools application, preparation of drawing paper and title block, lettering, dimension, and working lines.
VARIETY OF DRAWING TOOLS APPLICATIONo(1) Drawing board
VARIETY OF DRAWING TOOLS APPLICATIONo(2) Drafting table
VARIETY OF DRAWING TOOLS APPLICATIONo(3) T- Square
VARIETY OF DRAWING TOOLS APPLICATIONo(4) Set Squares
oDrawing of Angle
Method to use Set Square
VARIETY OF DRAWING TOOLS APPLICATION
o(5) Drawing pencil
VARIETY OF DRAWING TOOLS APPLICATIONo(6) Compass
VARIETY OF DRAWING TOOLS APPLICATION
o(7) Convex Compass
VARIETY OF DRAWING TOOLS APPLICATION
o (8) French curve
Sampling Template, Lettering and Lettering
VARIETY OF DRAWING TOOLS APPLICATION
o(9) Ruler, Eraser and Eraser Shield
VARIETY OF DRAWING TOOLS APPLICATION
o(10) Drawing Paper
VARIETY OF DRAWING TOOLS APPLICATION
o(11) Drafting Tape
VARIETY OF DRAWING TOOLS APPLICATION
oDrawing Tools
o (1) Paper setting on the drawing boardPREPARATION OF DRAWING PAPER AND TITLE BLOCK
o (2) Prepare the border lines and title block
NAME: COURSE: 1 BPC SCALE: 1:1 DATE: 09.09.2013
MATRIC: AP 123456 TITLE: LETTERING DRAW NO: UTHM/FPTP/ED/01
Section
PREPARATION OF DRAWING PAPER AND TITLE BLOCK
Step 5
100mm
UNIVERSITI TUN HUSSEIN ONN MALAYSIA
BPD 10102 ENGINEERING DRAWING
DRAWING TITLE:1. TITLE BLOCK2. LETTERING
NAMA
SCALE AS SHOWN
DATE
CHECKED PROF. MADYA DR. NARIMAH KASIM
DRAW NO. UTHM/FPTP/ED/01
LETTERING, DIMENSION AND WORKING LINES(1) Title block
The contents
change to
o (2) Types of Working Lines
Line name Form FunctionPencil grade
Construction line
Object line
Hidden line
Centre line
Border line
Light
Dark and heavy
Light
Light
Dark and heavy
Basic line to start drawing
To show an object
To show a hidden part in an object
To show a center part of a circle / curve
To draw a line outside the drawing
LETTERING, DIMENSION AND WORKING LINES
o Working Lines
Border line (HB) Drawing paper
Hidden line (HB)Centre line (H)Construction
line (2H)
Object line (HB)
o (3)LetteringThickness Application
5 mm or 6 mm Drawing title or important explanation
3 mm Dimension and important note
2 mm Additional notes
LETTERING, DIMENSION AND WORKING LINES
o Straight and Gradient Lettering
o(4) Lettering techniques
distance between lines of letters, usually from 3/5 to the full height of the letters
5mm
3mm
o(5) Dimension
Dimension line
o DimensionArrow size Dimensional angle
Dimensional curve
Dimensional circle
Small space dimension
Components of Construction Drawing
• 5 basic parts of construction drawing• (1) Title Block• (2) Border• (3) Drawing Area• (4) Revision Block• (5) Legend
ENGINEERING DRAWING
ENGINEERING DRAWING• 6 major types of drawing:
• Civil Drawing• Architecture Drawing• Structural Drawing• Plumbing• Electrical
CIVIL AND STRUCTURAL DRAWINGCIVIL ENGINEERING DRAWING
CIVIL AND STRUCTURAL DRAWINGSTRUCTURAL DRAWING
ARCHITECTURAL DRAWING
ARCHITECTURAL DRAWING
MECHANICAL (PIPING) DRAWING
MECHANICAL (PIPING) DRAWING
ELECTRICAL DRAWING
CONCLUSION
o After completion this chapter, students should be able to use the drawing tools, and draw title block, lettering and dimension in engineering drawing.
Thank You