Box Culverts & Rigid Frames.ppt - virginiadot.org
Transcript of Box Culverts & Rigid Frames.ppt - virginiadot.org
1
Precast Box Culverts & Precast Rigid Frames
2018 Bridge Construction Inspection School
Steve Malcolm
VDOT Staunton District
District Bridge Maintenance Manager
Learning Objectives
1. Identify basic components of box culverts and rigid frames.
2. Explain a procedure for field checking length of box culverts and rigid frames.
3. Show how box culverts and rigid frames are set into place.
4. Identify potential problem areas when setting box culverts and rigid frames.
2
2
PRECAST BOX CULVERTS3
PRECAST BOX CULVERTS
Did you know?...
Staunton District has approximately 3,500 total structures in inventory
Nearly 1,500 Culverts
3
PRECAST BOX CULVERTS
Box culverts are to have a minimum 36 ft² opening in order to be taken into our structure inspection system.
PRECAST BOX CULVERTS
Typical Section for a set of plans
Headwall
Invert Location
Curtain wall *
* Can be formed or unformed (poured against undisturbed earth)
4
PRECAST BOX CULVERTS
Stakeout work shall be in accordance with the Department’s current Survey Manual (Issued 2009)http://www.virginiadot.org/business/resources/LocDes/SurveyManual/SurveyManualEntire.pdf
The Contractor shall provide the Engineer with a record copy of survey drawings, field notes and computations prior to the use of said stakeout information for construction.
PRECAST BOX CULVERTS
(refer to Survey Manual)
5
PRECAST BOX CULVERTS
Lengths and Inverts to be field verified
Procedure for checking Box Culvert (from VDOT Survey Manual)
PRECAST BOX CULVERTS
Sample stakeout from VDOT Survey Manual
6
PRECAST BOX CULVERTS
Curtain Wall Installation Tips:
• Placement according to design (length and width)
• Skew or square end sections
• Allow for joint growth
• Form according to invert grade
• Right of Way limits
11
PRECAST BOX CULVERTS
12
Curtain Wall Installation - Formed
7
PRECAST BOX CULVERTS
13
Curtain Wall Installation - Formed
PRECAST BOX CULVERTS
14
Curtain Wall Installation - Unformed
8
PRECAST BOX CULVERTS15
Countersinking
PRECAST BOX CULVERTS
16
Curtain Wall Installation - Bedding
9
PRECAST BOX CULVERTS
Typical setting of box culvert sections
PRECAST BOX CULVERTS
18
Field verify size of box – Span x Height
10
PRECAST BOX CULVERTS
19
Lifting Slings and Cups
PRECAST BOX CULVERTS
20
Shims necessary when lifting holes are mislocated during fabrication
11
PRECAST BOX CULVERTS
Typical setting of box culvert sections
PRECAST BOX CULVERTS
Typical setting of box culvert sections
12
PRECAST BOX CULVERTS
Pulling sections together
PRECAST BOX CULVERTS
24
Pull pins and chains
13
PRECAST BOX CULVERTS
25
Pull hole size andpull pin diameter!
PRECAST BOX CULVERTS
26
Waterproofing joints and backfilling
14
PRECAST BOX CULVERTS
27
Staged construction
PRECAST BOX CULVERTS
Setting multiple barrels
15
PRECAST BOX CULVERTS
3” to 6” buffer zone betweenmultiple barrels - VDOT Spec. 302.03
PRECAST BOX CULVERTS
30
Setting width of buffer zone with dimensional lumber
16
PRECAST BOX CULVERTS
Buffer zone after concrete closure pour after the closure pou
PRECAST BOX CULVERTS
Precast Segmental Box Culvert
17
PRECAST BOX CULVERTS
Precast Segmental Box Culvert
PRECAST BOX CULVERTS
Problem areas – wing walls
18
PRECAST BOX CULVERTS
Problem areas – wing walls
PRECAST BOX CULVERTS
Problem areas – lack of cover from fabricator causes future maintenance issues (delamination and spalling)
19
PRECAST BOX CULVERTS
37
Approach guardrail and delineators
Need picture with approach guardrail!
PRECAST BOX CULVERTS
38
Multi-barrel mono box
20
Refer to VDOT Spec. 302 for Box Culverts
Scarify a Road Surface (Show video)
Comments/Questions?
PRECAST BOX CULVERTS
PRECAST RIGID FRAMES
Precast units are similar to box culverts except…
21
PRECAST RIGID FRAMES
…they have no bottom.
PRECAST RIGID FRAMES
Walls of rigid frame units rest on cast-in-place footings.
22
PRECAST RIGID FRAMES
Used where high rock is present in stream bed.
PRECAST RIGID FRAMES
Sub-footing used to provide stable base for footing that supports frames.
23
PRECAST RIGID FRAMES
Plan sheet drawing for typical rigid frame design(Route 220 over Chimney Run in Bath County)
Plan sheet drawing for typical rigid frame design(Route 220 over Chimney Run in Bath County)
PRECAST RIGID FRAMES
24
PRECAST RIGID FRAMES
Keyway Section (for Rigid Frame to sit in)
PRECAST RIGID FRAMES
Setting frame on Route 220 over Chimney Run in Bath County
25
PRECAST RIGID FRAMES
Sections usually transported on their side.
PRECAST RIGID FRAMES
Once sections are lifted from the truck…
26
PRECAST RIGID FRAMES
they are temporarily set back down…
PRECAST RIGID FRAMES
and are repositioned before being set onto the footing.
27
PRECAST RIGID FRAMES
Sections may also be skewed
PRECAST RIGID FRAMES
Frame sections are set on neoprene bearing pads
28
PRECAST RIGID FRAMES
Watch out for damaged sections and exposed reinforcing steel
PRECAST RIGID FRAMES
Pulling sections together
29
PRECAST RIGID FRAMES
Make sure sections come together
PRECAST RIGID FRAMES
Use high-strength, non-shrink grout to fill keway joints
30
PRECAST RIGID FRAMES
Typical wing joint details
PRECAST RIGID FRAMES
Backfilling and installing guard rail posts
31
PRECAST RIGID FRAMES
Completed project!
PRECAST RIGID FRAMES
In Review, Precast Rigid Frames:
Sit on sound rock and require no bottom slab (unlike box culverts)
Can be set in an efficient manner once footings are in place
Are designed to be used in various situations that may require skews or being on a grade
Comments/Questions?