BMW S54 Valve Adjustment...

19
Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal safety of those performing the repairs. Standard safety procedures and precautions (including use of safety goggles and proper tools and equipment) should be followed at all times to eliminate the possibility of personal injury or improper service which could damage the vehicle or compromise its safety. BMW S54 Valve Adjustment Procedure

Transcript of BMW S54 Valve Adjustment...

Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal safety of those performing the repairs. Standard safety procedures and precautions (including use of safety goggles and proper tools and equipment) should be followed at all times to eliminate the possibility of personal injury or improper service which could damage the vehicle or compromise its safety.

BMW S54Valve Adjustment Procedure

ECS TUNING 1000 SEVILLE RD. WADSWORTH, OH 44281 1.800.924.5172 WWW.ECSTUNING.COM 2

BMW S54 VALVE ADJUSTMENT

Table of Contents

®

If you own a BMW with the S54 6 cylinder engine, don’t overlook the valve adjustment. It’s a critical part of the routine maintenance required for this engine, and it’s part of the inspection I & II services that the Service Interval Indicator will alert you to. Even though the actual service intervals will vary depending on your driving habits, the valve adjustment is required at approximately every 30,000 miles.

Thanks to the forward thinking of the engineers at BMW, these are very simple valve adjustments, however you will need to have a few special things like a shim kit, shim tool, and feeler gauges, as well as the standard basic hand tools. While you’re at it, this is also a perfect time to replace the valve cover gasket. Just to make sure you have everything on hand before you begin, take a look at the specialty and required tools, and give these instructions a quick read through. Thank you for looking to ECS Tuning for all your performance and repair needs. We appreciate your business!ECS Difficulty Gauge

I I I I I I I I I

I I I I

I I I

I I I I I

I I I I I I I I I I I I I I I I I I I I I I

1

2 4

3

Advanced - 3

Pro - 4

2 - Moderate

1 - Easy

BMW S54 Valve Adjustment

INTRODUCTION

This complete valve cover gasket kit will put the finishing touches on your valve adjustment!

ES#1893860

ECS TUNING 1000 SEVILLE RD. WADSWORTH, OH 44281 1.800.924.5172 WWW.ECSTUNING.COM 3

BMW S54 VALVE ADJUSTMENT

Table of Contents

®

Required Tools and Equipment ................................................................................pg.4

Specialty Tools ................................................................................................................pg.5

Shop Supplies and Materials .....................................................................................pg.7

Installation and Safety Information ........................................................................pg.8

Getting Started...............................................................................................................pg.9

Adjusting the Valves .....................................................................................................pg.10

Torquing Tips ..................................................................................................................pg.16

Torque Specifications ...................................................................................................pg.17

Schwaben Tools .............................................................................................................pg.18

TABLE OF CONTENTS

ECS TUNING 1000 SEVILLE RD. WADSWORTH, OH 44281 1.800.924.5172 WWW.ECSTUNING.COM 4

BMW S54 VALVE ADJUSTMENT

Table of Contents

®

• Protecta-Sockets (for lug nuts) ........................................................ES#2221243• 3/8” Drive Ratchet ..................................................................... ES#2765902• 3/8” Drive Torque Wrench ....................................................... ES#2221245• 3/8” Drive Deep and Shallow Sockets ................................. ES#2763772• 3/8” Drive Extensions ............................................................... ES#2804822• Hydraulic Floor Jack ................................................................... ES#240941• Torx Drivers and Sockets ...................................................................ES#11417/8• 1/2” Drive Deep and Shallow Sockets ................................. ES#2839106• 1/2” Drive Ratchet• 1/2” Drive Extensions• 1/2” Drive Torque Wrench ........................................................ ES#2221244• 1/2” Drive Breaker Bar ................................................................ ES#2776653• File Set• Air Nozzle/Blow Gun• Bench Mounted Vise• Crows Foot Wrenches• Hook and Pick Tool Set .............................................................. ES#2778980

• 1/4” Drive Ratchet ...............................................................................ES#2823235• 1/4” Drive Deep and Shallow Sockets ................................. ES#2823235• 1/4” Drive Extensions ............................................................... ES#2823235• 1/4” Drive Torque Wrench• Plier and Cutter Set ................................................................... ES#2804496• Flat and Phillips Screwdrivers .......................................................ES#2225921• Jack Stands .............................................................................................ES#2763355• Ball Pein Hammers• Pry Bar Set ...............................................................................................ES#1899378• Electric/Cordless Drill• Wire Strippers/Crimpers• Adjustable (Crescent) Type Wrenches• Drill Bits• Punch and Chisel Set• Hex Bit (Allen) Wrenches and Sockets ..........................................ES#11420• Thread Repair Tools .............................................................................ES#1306824• Open/Boxed End Wrench Set ........................................................ES#2765907

Standard Automotive Tools Available On Our WebsiteRequired For This Install

Note: The tools required for each step will be listed by the step number throughout these instructions.REQUIRED TOOLS

ECS TUNING 1000 SEVILLE RD. WADSWORTH, OH 44281 1.800.924.5172 WWW.ECSTUNING.COM 5

BMW S54 VALVE ADJUSTMENT

Table of Contents

®

SPECIALTY TOOLS

These OE feeler gauges have the length and angle for easy measurements

ES#197828 ES#2748830

These shims are a must-have for the valve adjustment.

ES#197892

This special crankshaft socket may be required on early M3 models (see page 11)

ECS TUNING 1000 SEVILLE RD. WADSWORTH, OH 44281 1.800.924.5172 WWW.ECSTUNING.COM 6

BMW S54 VALVE ADJUSTMENT

Table of Contents

®

SPECIALTY TOOLS

This valve shim tool has a special bend on the end and a magnet in just the right spot to reach in and pick up the valve shims.

ES#2986423

The BMW fan clutch tools are very helpful for removing the fan/clutch. The wrench fits the large nut that holds the fan/clutch to the water pump and the holding fixture will lock onto two of the water pump bolts so you can hold it stationary to break the fan loose.

ES#2627584

ECS TUNING 1000 SEVILLE RD. WADSWORTH, OH 44281 1.800.924.5172 WWW.ECSTUNING.COM 7

BMW S54 VALVE ADJUSTMENT

Table of Contents

®

Standard Shop Supply Recommendations: We recommend that you have a standard inventory of automotive shop supplies before beginning this or any automotive repair procedure. The following list outlines the basic shop supplies that we like to keep on hand. Shop supplies with a hyperlink are available on our website.

• Hand Cleaner/Degreaser - Click Here• Pig Mats - for protecting your garage floor and work area from spills and stains - Click Here• Spray detailer - for rapid cleaning of anything that comes into contact with your paint such as brake fluid - Click Here• Micro Fiber Towels - for cleaning the paint on your car - Click Here• Latex Gloves - for the extra oily and dirty jobs - Click Here• Medium and High Strength Loctite Thread lock compound - to prevent bolts from backing out - Click Here• Anti-Seize Compound - to prevent seizing, galling, and corrosion of fasteners - Click Here• Aerosol Brake/Parts Cleaner - for cleaning and degreasing parts• Shop Rags - used for wiping hands, tools, and parts• Penetrating oil - for helping to free rusted or stuck bolts and nuts• Mechanics wire - for securing components out of the way• Silicone spray lube - for rubber components such as exhaust hangers• Paint Marker - for marking installation positions or bolts during a torquing sequence• Plastic Wire Ties/Zip Ties - for routing and securing wiring harnesses or vacuum hoses• Electrical tape - for wrapping wiring harnesses or temporary securing of small components

SHOP SUPPLIES AND MATERIALS

ECS TUNING 1000 SEVILLE RD. WADSWORTH, OH 44281 1.800.924.5172 WWW.ECSTUNING.COM 8

BMW S54 VALVE ADJUSTMENT

Table of Contents

®

• RH refers to the passenger side of the vehicle.• LH refers to the driver side of the vehicle.• Always use the proper torque specifications.• If applicable to this installation, torque specifications will be listed throughout the document and at the end as well.• Please read all of these instructions and familiarize yourself with the complete process BEFORE you begin.

• Park your car in a safe, well lit, level area.• Shut the engine off and remove the key from the ignition switch.• Make sure any remote start devices are properly disabled.• ALWAYS wear safety glasses.• Make sure the parking brake is applied until the vehicle is safely lifted and supported.• If using an automotive lift, be sure and utilize the factory specified lift points. Lifting a vehicle in an incorrect location can cause damage to the• suspension/running gear.• When lifting a vehicle using a jack, always utilize the factory specified lift points. Lifting a vehicle in an incorrect location can cause• damage to the suspension/running gear. ALWAYS support the vehicle with jack stands.• ALWAYS read and follow all safety information and warnings for the equipment you are using.

ECS Tuning cares about your health and safety. Please read the following safety information. This information pertains to automotive service in general, and while it may not pertain to every job you do, please remember and share these important safety tips.

Never get underneath a vehicle that is supported only by a jack. Always make sure that the vehicle is securely supported on jack stands.

INSTALLATION NOTES

PREPARATION AND SAFETY INFORMATION

ECS TUNING 1000 SEVILLE RD. WADSWORTH, OH 44281 1.800.924.5172 WWW.ECSTUNING.COM 9

BMW S54 VALVE ADJUSTMENT

Table of Contents

®

There are a few things you’ll need to remove in order to perform a valve adjustment, and we’re betting if you’re going to tackle this job you don’t need us to step you through the easy stuff, but we’ll give you a quick run-down anyhow. The following items will need to be removed:

2. Radiator Fan and Shroud

1. Air Box

3. Cabin Filter Housing

4. Suspension Cross Brace

5. Engine Top Cover, Valve Cover, and Ignition Coils

1

3

5

2

4

GETTING STARTED

The engine should be cool before performing the valve adjustment (no more than 95 degrees Fahrenheit).

ECS TUNING 1000 SEVILLE RD. WADSWORTH, OH 44281 1.800.924.5172 WWW.ECSTUNING.COM 10

BMW S54 VALVE ADJUSTMENT

Table of Contents

®

ADJUSTING THE VALVES

Step 1:

Step 2:

5/8” Spark Plug Socket, Ratchet

OK, now that you have the valve cover off, you’re almost ready for the valve adjustment, but first, remove the spark plugs. This will make it easy to rotate the engine over as you move through the cylinders.

Valve adjustment is achieved by checking and adjusting the clearance between the cam lobe base circle and rocker arm directly underneath.

Intake valve clearance:0.18 - 0.23mm (0.0070 - 0.0090 in.)

Exhaust valve clearance:0.28 - 0.33mm (0.0110 - 0.0130 in.)

Since the clearance is different for the intake and exhaust valves, it’s easiest to start with one camshaft, adjust all valves, then move on to the other. This way, you will not have to switch out the feeler gauge sizes over and over.

ECS TUNING 1000 SEVILLE RD. WADSWORTH, OH 44281 1.800.924.5172 WWW.ECSTUNING.COM 11

BMW S54 VALVE ADJUSTMENT

Table of Contents

®

Step 3:

Step 4:

Decide which camshaft you would like to start with, then using the socket identified in step 3, rotate the engine in a clockwise direction so one set of camshaft lobes is pointing upwards. It is not necessary to begin with any particular cylinder, so you can start with the first set of lobes that point upward.

Inspect the front of the crankshaft pulley (you may need to use a mirror). You will see either a large hex or four Torx bolts. The large hex will require a 32mm socket, and if equipped with the four Torx bolts, you will need a special crankshaft socket, ES#197892.

O T O T

Requires 32mm Socket

Cam lobes pointing upwards

ADJUSTING THE VALVES

ECS TUNING 1000 SEVILLE RD. WADSWORTH, OH 44281 1.800.924.5172 WWW.ECSTUNING.COM 12

BMW S54 VALVE ADJUSTMENT

Table of Contents

®

Step 5:

Step 6:

Precise cam lobe position is not necessary as you adjust the valve clearance. It can be checked anywhere along the cam lobe base circle (the lowest part of the lobe where the valve is closed). For clearance and access it is easiest to measure and install shims with the lobes pointing straight up.

Using the feeler gauge, measure the clearance on the lobes you are starting with. Remember, the intake and exhaust valves have different clearance specifications.

ADJUSTING THE VALVES

Base Circle

Intake valve clearance:0.18 - 0.23mm (0.0070 - 0.0090 in.)

Exhaust valve clearance:0.28 - 0.33mm (0.0110 - 0.0130 in.)

Rocker Arm

Feeler Gauge

Cam Lobe

Valve Shim

Cam Lobe

ECS TUNING 1000 SEVILLE RD. WADSWORTH, OH 44281 1.800.924.5172 WWW.ECSTUNING.COM 13

BMW S54 VALVE ADJUSTMENT

Table of Contents

®

Step 7:

Step 8:

If the valve clearance is correct, move onto the next. If it is too tight or too loose, you will need to replace the shim with a different size. Use multiple different feeler gauges to determine how much of a change is required.

There is a rocker arm retaining clip behind each set of cam lobes. Pull it up and remove it (these will come off very easily).

ADJUSTING THE VALVES

In preparation to change a valve shim, place clean shop rags over the exposed timing chain openings, oil returns and vents, and spark plug holes.

ECS TUNING 1000 SEVILLE RD. WADSWORTH, OH 44281 1.800.924.5172 WWW.ECSTUNING.COM 14

BMW S54 VALVE ADJUSTMENT

Table of Contents

®

Step 9:

Step 10:

Now, using your finger, simply slide the rocker arm off to the side, and you will have clear access to the valve shim.

This is where the special valve shim tool is needed. Simply reach in with the magnet and pick up the valve shim. It’s easy - but this is also where you’ll have to be careful. These are fairly easy to drop, so you’ll want to move slowly and carefully as you draw out the shim.

ADJUSTING THE VALVES

Rocker Arm

Valve Shim

Valve Shim

Valve Shim Tool

ECS TUNING 1000 SEVILLE RD. WADSWORTH, OH 44281 1.800.924.5172 WWW.ECSTUNING.COM 15

BMW S54 VALVE ADJUSTMENT

Table of Contents

®

Step 11:

Step 12:

Measure the valve shim that you removed, then calculate the new size you will need in order to obtain the correct adjustment. Select the correct new shim from your kit.

Carefully install the new shim, slide the rocker arm back in place, and install the rocker arm retaining clip.

ADJUSTING THE VALVES

Check the valve clearance to make sure you have used the correct shim, then repeat the procedure for all valves.

Reassemble the vehicle and your valve adjustment is complete!

Rocker Arm

Feeler Gauge

Cam Lobe

Valve Shim

See page 17 for some helpful torque specs.

ECS TUNING 1000 SEVILLE RD. WADSWORTH, OH 44281 1.800.924.5172 WWW.ECSTUNING.COM 16

BMW S54 VALVE ADJUSTMENT

Table of Contents

®

Torque to Yield or “Stretch” Bolts

A ribbed bolt is identified by the ribs on the contact surface

A non-ribbed bolt is identified by the smooth contact surface

Ribbed vs. Non-Ribbed Bolts

Many bolts will have a torque specification listed in the format - xx Nm (xx Ft-lbs) + xx degrees. These bolts are torque to yield bolts, commonly referred to as “stretch” bolts. The correct procedure for torquing these bolts is:

Note - Some bolts may have two or more stages of torquing before the final stage of “stretching” the bolts.

All Torque to Yield bolts should only be used once and should be replaced each time they are removed. If they are reused, they will not be able to achieve the proper clamping force with the specified torque.

When tightening more than one bolt in a specified sequence, be sure to mark each fastener with paint immediately after performing the final stage or “stretching” of the bolts. This will ensure that you keep track of which bolts have already been “stretched”.

Stage One - Torque the bolt(s) to the initial Nm or Ft-lb specification. If there is more than one, be sure to torque them in the correct sequence.Stage Two - Tighten or “stretch” the bolt(s) the additional specified number of degrees. If there is more than one, be sure to follow the correct sequence.

Lubrication

Torque specifications are always listed for a dry fastener (no lubrication) unless specified otherwise.

Some fasteners require lubrication on the threads -or- on the contact surface while torquing. These fasteners will be listed with the specific location and type of lubrication required. Always follow manufacturers recommendations exactly.

Do not lubricate the threads of any fastener unless it is specifically recommended by the manufacturer.

Lubricating a fastener that is intended to be installed dry and then torquing it to factory specifications will increase the clamping force and stress on the fastener and components, which can result in damage or failure.

Ribbed and Non-Ribbed bolts in the same location generally require a different torque specification.

TORQUING TIPS

ECS TUNING 1000 SEVILLE RD. WADSWORTH, OH 44281 1.800.924.5172 WWW.ECSTUNING.COM 17

BMW S54 VALVE ADJUSTMENT

Table of Contents

®

TORQUE SPECIFICATIONS

Coil Pack Mounting Screws ......................................................................................................................... 4 Nm (3 Ft-lbs)

Valve Cover Oil Drain Hose Banjo Bolt ...................................................................................................... 25 Nm (18.5 Ft-lbs)

Valve Cover Mounting Bolts ........................................................................................................................ 8 Nm (6 Ft-lbs)

Spark Plugs ....................................................................................................................................................... 25 Nm (18 Ft-lbs)

ECS TUNING 1000 SEVILLE RD. WADSWORTH, OH 44281 1.800.924.5172 WWW.ECSTUNING.COM 18

BMW S54 VALVE ADJUSTMENT

Table of Contents

®

At ECS Tuning, we carry a line of high quality Schwaben tools and equipment to help you build your ultimate tool collection. Never before has affordability and quality been so closely related. Our entire Schwaben line is subjected to strict in house testing for strength and durability. See what we have to offer and equip your garage without breaking the bank.

SCHWABEN - BUILD THE ULTIMATE TOOL COLLECTION

Your BMW S54 valve adjustment is complete!

These instructions are provided as a courtesy by ECS TuningProper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal safety of those performing the repairs. Standard safety procedures and precautions (including use of safety goggles and proper tools and equipment) should be followed at all times to eliminate the possibility of personal injury or improper service which could damage the vehicle or compromise its safety.

Although this material has been prepared with the intent to provide reliable information, no warranty (express or implied) is made as to its accuracy or completeness. Neither is any liability assumed for loss or damage resulting from reliance on this material. SPECIFICALLY, NO WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR ANY OTHER WARRANTY IS MADE OR TO BE IMPLIED WITH RESPECT TO THIS MATERIAL. In no event will ECS Tuning, Incorporated or its affiliates be liable for any damages, direct or indirect, consequential or compensatory, arising out of the use of this material.