Direction générale de l'inspection

Montréal, 22 novembre 2016.

We bring your attention to certain requirements of the regulation respecting pressure vessels, and the codes and standards adopted :

The Régie du bâtiment du Québec (RBQ) informs you that your application for the registration of designs has been evaluated and that the design was registered the 22-11-2016 under the Canadian Registration Number (CRN\NEC) :

MR. W.A. MILLER WEST

Manufacturer : JINAN MEIDE CASTING CO. LTD.

3 NANMEN ROAD

PINGYIN COUNTY JINAN

CHINE

Dear Sir,

LIGHTHOUSE ASSISTANCE INC.

P.O. BOX 488

MONTAGUE P.E.I.

CANADA C0A 1R0

OUR REFERENCE : 955867

Subject: Registration of designs - Confirmation of approval

The drawing number, including the revision number registered under this CRN, must be indicated on the Manufacturer's Data Report for equipment manufactured according to the CRN.

■

■

■

This notice of approval does not relieve the constructor of his responsibilities with respect to the design or construction of equipment manufactured according to this CRN.

Yours sincerely,

The manufacturer must maintain a valid quality control program to produce according to the CRN.

The manufacturer shall submit to the RBQ a copy of Manufacturer's Data Report for equipment manufactured according to this CRN within 30 days following the signing of this Declaration.

PIPE FITTINGS CATALOGSDesign number :

Bureau d’expertise et d’homologation en équipements sous pression

0A11253.56.

www.rbq.gouv.qc.ca

545, boul. Crémazie Est, 7ième étageMontréal (Québec) H2M 2V2Téléphone : 514 873-6459Sans frais : 1 866 262-2084

Montréal

September28, 2016 MILLER WEST LIGHTHOUSE ASSISTANCE INC PO BOX 488 MONTAGUE PE C0A 1R0 CA Service Request Type: BPV-Fitting Registration Service Request No.: 1938990 Your Reference No.: 11921 Registered to: JINAN MEIDE CASTING COMPANY Dear MILLER WEST, Technical Standards and Safety Authority (TSSA) is pleased to inform you that your submission has been reviewed and registered as follows: CRN No.: 0A11253.5R2 Main Design No.: see attached "Part of CRN" for the scope Expiry Date: 28-Sep-2026 Please be advised that a valid quality control system must be maintained for the fitting registration to remain valid until the expiry date. CRN Note: See attached “Part of CRN’ for the scope. The stamped copy of the approved registration and the invoice are mailed separately. Should you have any questions or require further assistance, please contact a Customer Service Advisor at 1.877.682.TSSA (8772) or e-mail customerservices@tssa.org. We will be happy to assist you. When contacting TSSA regarding this file, please refer to the Service Request number provided above. Yours truly, Charley Dong, M.Sc. P.Eng. Mechanical Engineer Tel.: 416-734-3436 Fax: 416-231-6183 Email: cdong@tssa.org

Inspection and Technical Services Manitoba 500 - 401 York Avenue Winnipeg Manitoba R3C 0P8 T (204) 945-3373 F (204) 948-2309

www.firecomm.gov.mb.ca/codes_steam_pressure.html December 23, 2016

Lighthouse Assistance

Box 488

Montague, PEI C0A 1R0

Attn: Miller West

REGISTRATION OF VALVES AND FITTINGS

Manufacturer: JINAN MEIDE CASTING CO. LTD.

The design(s) for the following Valves/Fittings has been received by us and has been examined and accepted

for registration in the Province of Manitoba as follows.

DRAWING / CATALOGUE CRN FILE

PIPE NIPPLES AND DUCTILE IRON CAST IRON

FITTINGS CATALOGUES AS NOTED 0A11253.54 37092

An invoice covering survey and registration fees is enclosed.

NOTE: CRN registered under reciprocal agreement & is conditional based on compliance with the notes set

by the original issuing Jurisdiction: ABSA. This registration expires September 28, 2026.

This registration is valid until the indicated expiry date only if the Manufacturer maintains a valid quality

management system approved by an acceptable third-party agency until that date. Should the approval of the

quality management system lapse before the expiry date indicated above, this registration shall become void.

The registration of this design does not relieve the manufacturer, the owner or his agent of the responsibility

for the design or construction of a fitting in accordance with the applicable Acts, Codes and Standards.

Inspection and Technical Services assumes no responsibility by registering designs, examining plans and/or

inspecting equipment or facility.

Regards,

Ryan Orlesky, C.E.T. Design Surveyor Office of the Fire Commissioner Inspection and Technical Services Manitoba 508 - 401 York Avenue Winnipeg, Manitoba, R3C 0P8 Phone: 204-945-3373 Email: ryan.orlesky@gov.mb.ca

O F F I C E o f t h e F I R E C O M M I S S I O N E R

9410 - 20 Ave N.W.Edmonton, Alberta, Canada T6N 0A4

Tel: (780) 437-9100 / Fax: (780) 437-7787

October 18, 2016

NIPPLES, COUPLINGS,CAST IRON FITTINGS

MONTAGUE, PE C0A 1R0294 LOWER MONTAGUE ROADPO BOX 488

CRN :

Drawing No. :

Accepted on:0A11253.52

Reg Type: Addition to Acc. Fitting September 28, 2026

October 18, 2016

Design registered in the name of : JINAN MEIDE CASTING CO LTD

Expiry Date:

CATALOGUES MECH JINAN PIPE NIPPLES & PIPE FITTINGS As Noted

Fitting type:

Attention:

The design submission, tracking number 2016-05233, originally received on September 30, 2016 wassurveyed and accepted for registration as follows:

Sincerely,

GRYNCHUK, MILLA

An invoice covering survey and registration fees will be forwarded from our Revenue Accounts.

If you have any question don't hesitate to contact me by phone at (780) 433-0281 ext 3330 or fax (780)437-7787 or e-mail grynchuk@absa.ca.

The registration is conditional on your compliance with the following notes:

As indicated on AB-41 Statutory Declaration form and submitted documentation, the code of construction isother engineering analysis.

This registration is valid only for fittings fabricated at the location(s) covered by the QC certificate attached to theaccepted AB-41 Statutory Declaration form.

This registration is valid only until the indicated expiry date and only if the Manufacturer maintains a valid qualitymanagement system approved by an acceptable third-party agency until that date.

Should the approval of the quality management system lapse before the expiry date indicated above, thisregistration shall become void.

This is CRN renewal CRN covers :Page #7 (size 1/8” thru 8”) & Page 10 (size 1/8” thru 6”) Pipe NipplesCataloguePage # 17 (size ½” thru 4”) Pipe Fittings Catalogue

LIGHTHOUSE ASSISTANCE INC

Miller West mwest@mrcrn.comEmail:

Page 1 of 12016-05233

Amra :1C1 PAL AFFAIRS ~'l~

Alberta Boilers Safety Association

STATUTORY DECLARATION Registration of Fittings

SU ZHAOXIA"

SALES DIRECTOR

AB-41 00111

In this space, show facsimile of manufacturer's logo or trademark as it will appear on the fitting.

«®>

(company title, e.g. v:ce president. plant manager, chief engineer) (must be in a position of authority)

of JINAJ\ MEIDE CASTING CO. LTD.

(name of manufacturer)

located at linan Meide Technopark, South of No. I05 National Highway, Industrial Park, Pingyin, linan, China 250400

(plant address)

do solemnly declare that the fittings listed hereunder, which are subject to the Safety Codes Act (check one)

C8J comply with the requirements of AST\1 A733,ASTM A53/Al06/A333/A865,ASTM A126, ASME B I6.4/B1 6.14.ASME B 1.20.1 which specifies the dimensions,

(titl" of recognized North American Standard)

maicrials of construction, pressure/temperature ratings and identification marking of the fittings, or

re DOt covered by the provisions of 2. :ccognized North American standard and are therefore manufactured to

comply \vith as supported by the attached data which identifies the dimensions,

materials of construction, press;rre/temperature ratings and the basis for such ratings, and the marking of the fittings

for identification.

I further declare that the manufacture of these fittings is controlled by a quality control program which has been verified by the

following authority, BVQI as being suitable for the manufacture of these fittings to the

stated standard. The fittings covered by this cxlaration, for which I seek registration, are CAST IRON FITTINGS,

EA.,\1 LESS AND WELDED NIPPLES, STEEL MERCHANT COUPLINGS

- support of this application, the following information, calculations and/or test data are attached:

CATALOGUE

DECLARED before me at in the _________ of

t.;-js day of __--::-,----.,..,-__ _ __ (Month) '-(Year) j;jJ~(print)----___________~ ~

(Signature of Applicant) (sign) ______________

(A Commissioner of Oaths)

For Office Use Only

-=-,J the best of my knowledge and belief, the application meets the requirements of the Safety Codes Act and CSA Standard 8 51 , Clause 4.2, and is accepted for registration in Category ___+L.L________________---,-."",-__

Registration Number: 0 All 25 3. 5 2 t-:;~,. /) c · I ~C.<4 :. ~. /\ ----'

- (For the Administrator/Chief Inspector of Alb~lta) Dale Registered: OCT 1B 2C;ti Expiry Date: ,J:,-err.';;!'0 ,;J-C: .:L6­